Arrived on site for dryer not heating upon arrival conf8rmed issue. Upon further testing I found cutoff broken and element coils bowing/sagging. Replaced both parts. Found dryer could heat as designed but found clog in venting of home with vent tester. Informed customer they would need a proper dvc done prior to using dryer. Unit is functioning as designed. Call complete

"Arrived on site for washer, inspected unit and work area. Tested unit and found low water pressure on the cold side. Removed water hose on the wall valve and found the screen clogged. Explained to CX that those screens need to stay clean to have good water pressure. Tested unit and its operating as designed. No leaks observed during service. Job completed."

Arrived on site to test unit for unit not draining. Test unit and found drain pump disconnected. Secured connection test unit and unit test good job complete.

"Ride down site over the range fented making noise when fan is on . Found construction debris in blower housing . Removed debris, fan is normal sounding now and venting properly . No other issues found. Job complete"

"Arrived on site and found water filter is jammed, filter housing will not disengage. Replaced filter housing and customer has a new water filter already on hand. Refrigerator is now dispensing water properly, job complete"

Arrived onsite and found installation failure which resulted latch strike bending. Repaired installation and latch. Unit is now operating as designed. All checks good.

Arrived onsite and found no cool issue caused by locked compressor. Compressor will need to be replaced to repair. Advised customer on wait time for parts and scheduling. ; ordrng 1 R600a (R600a)

Arrived on site to test unit for unit not heating. Test unit and found and tod. Ordering new tod ; ordrng 1 WP9759242 (Tod)

Arrived on site for washer not draining and leaving load wet . Found slider ring out of position . Also gear case is leaking oil ; ordrng 1 W11393685 (Gearcase)

"(JM) Arrived onsite to inspect washer not draining excess water at the end of a cycle. I entered diagnostics and found error codes F8E1, F5E2, F0E2, F1E1, F5E3. I entered the service test mode and ran a test cycle. The drain pump turned on and drained the tub as designed. The water valves filled as designed. However, at the end of the test cycle the unit was still filled with water. I manually tested the the drain pump outside of the diagnostic test cycle and it is working as designed. Unit will need a new control board and I advised the CX to purchase a surge protector. I may also need to replace the water valve, but I need to rule out the board first. Ordering W11448786 (electric control). Office to RS.; ordrng 1 W11448786 (CNTRL-ELEC)"

"Arrived onsite for Not Cooling. Upon arrival inspected unit and is hot in both boxes. Found compressor turning on then after a few seconds, clicks and shuts off. Compressor Is pulling 12.8 amps. This is a r134a sealed system. Need to order sealed system parts.ordering evaporator, compressor, access valve, and uV drier ; ordrng 1 WPW10507886 (Compressor) and 1 W10836706 (Evaporator) and 1 Wpw10143759 (UV drier) and 1 W11506635 (Access valve)"

Arrived on site for refrigerator not cooling. Upon arrival confirmed issue and found temps around 15/51 (fc/rc). Found all fans and compressor running. Found no defrost issues. I then found fist sized rust hole in liner insulation causing internal cool air to escape to escape

"Arrived on site for micr not working. I inspected the unit and work area.I used my watt meter and tested the unit, I found it pulling less then 5 amps. I removed the unit from the cabinet and tested the magnetron, I found it ohming out correctly. I tested the transformer and found the secondary winding open. I spoke to the customer about what was needed; ordrng 1 W11371718 (Transformer)"

"Arrived on site for an ice machine that was not draining water. Upon arrival the customer stated they thought the external drain pump stopped working, and that the ice machine had leaked all onto the floor. They went out of town and when they came back the ice machine was completely full of water and a very large portion of their floor was covered in water. I put the unit into diagnostics mode and found the valve never energized. I checked voltage going to the valve and found none. This indicates a possibly bad water level sensor or control. I am ordering the recirc pump with the sensor integrated to install, and will order the control too. We will install the pump and test the unit. If the pump does not work then we will install the control. I gained access to the back of the unit and found the water line and drain line leaking. I showed and advised the customer on replacing these. I found the unit still within warranty, for it has a 36 month manufacture warranty. ordrng 1 W11542867 (Recirc Pump) and 1 W11034363 (Control)"

"Arrived on site to test unit for F2E1 error code, tested unit found error code present cycled power to unit but error is still present, will need console and control to fix issue due to this unit being a flush mount 2 men will be required for this job to prevent ant potential damage to cabinets, ordrng 1 W11232121 (Console)"

"Arrived on site for wall oven getting hot on the outside. I spoke to the customer and found out it is the floor next to the oven that is getting hot. The wall oven is installed into a cabinet below a cooktop. I inspected the unit and work area.I found the door hinges in good condition and the gasket it good shape. I put the unit into diagnostics and found no error codes. I tested the blower and found it working as designed. I explained how air flows in this unit. That it pulls air from the top and it blows out the bottom, and that with the oven on and the blower circulating air, the floor will heat up due to the unit venting down towards the floor. There is no way to change the air flow direction. The unit is working as designed. Job complete.

Arrived onsite for has a crack on the inner top part of the door. Upon arrival inspected unit and found the console has failed. Need to order console. ; ordrng 1 W11095590 (Console)

"Arrived on site. Found unit not powering on,ui unresponsive ui not powering unit on or entering diagnostics,reset power to unit,compressor and fans powered on ui responsive.

Arrived on site for no ice. Ran diagnostics E2 error code ran harvest test passed ran fill test no water removed housing found damaged heater unit will need a new heater and icemaker ; ordrng 1 W11226501 (Heater)

Arrived on site for dishwasher flashing and not staying on. I inspected the unit and work area. I powered the unit on and found it flashing and then not responding. I opened the junction box and tested voltage. I found no voltage at the junction. I gained access to the outlet and found no power at the outlet. I checked the breaker and found the breaker not tripped. I switched the dishwasher to the disposal outlet and tested it. It is working as designed. I spoke to the customer about having a electrician come out and inspect the outlet and switch.

Arrived onsite for oven door coming off hinge. Upon arrival inspected unit. Found left hinge came out of receiver. Repositioned hinge. Inserted door and door is now opening and closing properly.

"Arrived on site and inspected refrigerator and found fresh food evaporator Is frosted over, took one picture. Will need another fan scroll to correct issue. Also found fresh food door gasket Magnetic strip is not making contact with cabinet on the bottom. Took one picture. And sent it to tech line. 7734386939 User interface was already replaced on previous visit due to service pointer W11512766. Techline does not have any further recommendations other than replacing fan strobe and ensuring thermistor is in the correct location. If issue continues door seal maybe the issue and this cannot be corrected.

"Arrived on site for range, inspected unit and work area. CX complaint was both oven doors rubbing with each other. Removed lower oven door and found frame damage. CX was not able to see it when delivered. I called thechline and spoke to Steve SR#7734390675 and I sent pictures to him and based on what he saw unit is Then he transferred me to 1800-874-4698 and spoke to him Debra SR#7734243137 and they will be contacting CX for further action. O leaks where observed during service. Job completed."

"Arrived on site to test unit for not cooling in both compartments, tested unit found unit unplugged plugged unit back in and compressor starts right away, exposed evaporator, unit developed a good frost pattern, customer stated that he did not noticed evaporator frozen over just ice started to melt, ran diagnostics on ice maker to see is a potential water leak could be causing ice to melt, due to unit running good advised customer to monitor unit and when it does stop cooling not to unplug unit and call us back,

"Arrived on site to test unit for leak from under door area. Found in diagnostics lower spray arm not rotating as designed. When in certain positions spray arm is spraying water directly in corners causing water to bypass tub door lip and leak. Replaced spray arm, tested unit, unit working as designed. Recommended replaced middle spray are too.

Arrived on site to test unit for unit leaking and drain pump staying on. Test unit and found damaged tub will need to replace tub 2 hour job ; ordrng 1 W11409866 (Tub) and 1 2hours (2 hours)

"Arrived to inspect no ice. Another servicer had recently replaced the ice maker and I found they did not correctly instal the upper cover and fascia, creating excessive air movement within the low profile ice maker housing. I correctly reassembled the unit and tested the ice maker, ice maker fan, bin level sensor and thermistor. I also tested fill at the end and all operations were present. The FC was 10 and dropping during testing. The unit required chassis squaring and door matching. The CX will contact us if there are further issues. No leaks observed during service.

"Arrived on site for a washing machine getting an LF error and that was not dispensing water properly. I put the unit into diagnostics mode and found stored error codes F3E2 for inlet water temp fault, F0E3 for overload, and F8E1 for long fill. I cleared the error codes. I then ran a diagnostics cycle and found the hot valve not working properly. I found good voltage to it indicating a bad valve. I installed the valve and then test the unit. I found it now working as designed with no leaks observed at the time of service.

"Arrived on site to inspect dishwasher leaking water inside the tub. Upon further inspection, I found the tub full of water and the inlet was leaking into the tub. I found the water line is copper tubing as well. I recommended that the customer have the copper tubing replaced with a braided water hose due to the possibilities of the copper tubing leaking later on. /// to replace it. I am ordering the braided water hose and will return with all prescreened parts. Water left turned on at the customers request as they will turn the drain pump on occasionally to drain any water that leaked in from the valve. ; ordrng 1 TJ10SS72DW (Water hose) and 1 CNOTE (LSO FOR TRAINING)"

"Arrived on site to test unit for no heat at times, customer stated that unit drying good on timed dry but no on sensor mode, ordering moisture sensors, harness and vent tester,### ; ordrng 2 WP3387223 (Moisture)s and 1 WPW10298258 (Harness) and 1 WPW10106710 (Vent tester)"

Arrived on site to diagnose a range with an oven not heating.

Arrived on site to replace previously ordered parts for oven. Replaced lower blower and tested unit. Found all is functioning properly at this time and upper fan was not needed.

Arrived on site to diagnose a refrigerator that is not dispensing ice. Found dispenser chute clogged and cleared clog. Tested unit and found all is functioning properly at this time and no leaks were found at time of service.

Arrived on site to diagnose a dryer that is making unusual noise. Found front motor clip not installed properly and rubbing on motor shaft. Installed clip properly and tested unit. Found all is functioning properly at this time.

Arrived on site to diagnose a dryer that was making unusual noise. Customer already had another company correct issue and just wanted unit inspected. Tested all parts and components and found no failures to unit at this time. Advised customer on findings and no further repairs needed.

Arrived on site to diagnose a refrigerator that is slow to produce ice. Found freezer temps ok and icemaker cycling. Also no water issues found. Did not airflow in unit blocked by items and advised customer on airflow channels for proper operation. No further repairs needed and no leaks were found at time of service.

Arrived on site to diagnose a dishwasher that was damaged during installation. Found back left cornet of tub cracked and lower rack damaged. Both parts will need to be replaced to complete repairs and office to set return appointment. ; ordrng 1 W11513977 (Tub) and 1 W10161215 (Rack)

Arrived on site to diagnose a range that was damaged during installation. Found right side panel damaged and it will need to be replaced to complete repairs. Office to set return appointment. ; ordrng 1 WPW10162245 (Panel)

"Arrived on site to diagnose dishwasher with no power at unit, will not start. Examined unit and found good voltage to the unit.

Arrived on site to install new heater per SP W11540964. Installed new element and verified no water leaks or damage present. Call complete.

"Arrived on site to diagnose dryer that is not fully drying clothes. Ran unit and found it is heating, but not venting. Ran vent tester and found a bad airflow reading from it. Customer advised to have vents cleaned since unit isn't venting. Call complete."

Arrived on site to diagnose refrigerator that was not cooling. On arrival customer told me they had already resolved the issue. Informed them they are out of warranty and to follow up if issue returns. Unit is rental so we would need approval from the landlord. Call complete.

Arrived on site to install refrigerator door due to dented door from shipping. Used provided door and replaced right side RC door. Unit working as designed. Call complete.

Arrived on site to diagnose range with front left cooktop burner locked to high. Tested burner and on single or dual element it will lock to high and does not cycle. Replaced cracked element and infinite switch. Tested unit and verified its properly cycling. Call complete.

"Arrived on site to diagnose refrigerator not making ice. Customer said they found an E5 error. Checked via diagnostic and also confirmed E5. Checked Temps and found FC at -2, RC at 41. Icebox also at 41. Found temp set to 41. Lowered RC Temps to 37 per recommended, also advised cleaning condenser coil regularly. Tested and found unit does harvest, but slowly. Ordering icemaker to resolve. Office to schedule when we get part. ; ordrng 1 W11294907 (Icemaker)"

"Arrived on site to diagnose vent hood that is not properly shutting down the motor when retracting up and down, also found unit has to have the switch pressed in to go both up and down and lost the auto function. Found the switches / motor cam are not properly making contact when the motor is reaching the correct positions. Replaced all 3 motor related microswitches. Retested unit and found problem is still persisting, indicating some contact/geometry inside the motor assembly isn't making contact. Ordering complete motor assy with switches to resolve. Office to schedule. ; ordrng 1 W11230930 (Control Switch)"

"Arrived on site for dishwasher not cleaning properly. I inspected the unit and work area. I found F6e1 low no water, f6e4 float switch open. I found the lower spray arm not seated properly onto the outlet cover. I inspected the cover and spray arm I found some of the locking tabs damaged. I reseated the spray arm. I also found the unit not fully installed into the cabinet. I leveled the unit as best as possible. I ran a diagnostics cycle and found the motor working properly. I recommend the customer replace the lower spray arm and outlet cover

Arrived on site for range knobs getting hot to the touch. I inspected the unit and work area. I found the door hinges have lost some tension and are allowing the door to fall open and not hold tension while closed. I installed a new hinges. We leveled the unit properly. We ran a bake and found the knobs heating to around 90 degrees.

Arrived on site for dryer not heating. I inspected the unit and work area. I tested the unit and found it tumbling but the ignitor not glowing. I gained access to the ignitor and found it in good condition. I gained access to the thermal fuse and found it open. I installed a new fuse. I reassembled the unit and tested it. I found it working as designed.

"Arrived on site for fridge not making ice or producing water. I found the water line turned off and the inlet valve not seated properly. I reseated the valve and turned the water on. I tested the icemaker and water dispenser. Both are working now. The sound the tenant is hearing is the water valve opening while the ice maker is filling, this noise is usual. The unit is working as designed. Job complete."

Arrived on site to install a new heating element. I verified the model and serial number fall in range for service pointer W11540964. I installed the new heating element and tested it. It is now working as designed. Job complete. No water leaks detected.

Arrived on site to install previous diagnose parts. I gained access to the control and transformer. I replaced both. I reassembled the unit. I tested the light and blower motor. The unit is working as designed. Job complete.

"Arrived on site for washer not spinning out the clothes. I inspected the unit and work area. I inspected the gearcase and found it leaking oil. I ran a diagnostics cycle and found the gearcase starting to howl, like the bearings are going out.; ordrng 1 W11393685 (Gearcase)"

"Arrived on site for dishwasher not cleaning. I inspected the unit and work area. I found fault codes f10e2 vent wax motor failure f1e1 acu fault f8e2 inlet valve failure. I ran a diagnostics cycle and found the unit Leaking from the wash motor. I am ordering the vent motor, control, and returning with the sump and motor assembly to complete the repair. The office will reschedule. ; ordrng 1 W11416460 (Vent) and 1 W11410066 (Control)"

Arrived for cooling issue. FC 23?RC 58? Discussed with CX that he put unit into manual defrost. Removed old defrost timer and was very warm to the touch. I removed and replaced the defrost timer and tested. The unit operated as designed and I am applying our warranty to this service. No leaks observed during service.

"Arrived to inspect no water flow. I entered service test mode and found F4E3 F7E1 stored. I tested the sump assembly and it showed the correct ohms. The control would only momentarily apply voltage and I removed and replaced it. The issue persisted and I found the pump motor had been leaked on from a faulty sump assy seal, causing the resistance reading to be nearly the expected of the motor circuit. I removed and replaced the sump assembly and the issue was corrected. Operational test good, no leaks observed upon completion of service.

Arrived to inspect knobs rubbing. I found the left two burner knobs would rub during ignition and were much closer to the cooktop than the others. There was a steady slant to all the knobs that denoted an issue with the manifold assy. The cooktop had several marks and decals had sections missing. No gas leaks detected during service. ; ordrng 1 W11204395 (Cooktop) and 1 W10594396 (Manifold Assy)

Arrived on site for dishwasher not draining. Gain access to unit put unit into diagnostics mode found error F6E4. On inspection water was standing in the bottom of DW. CX says it is a new build and the DW never worked. Pulled drain line off garbage disposal and found knock out still intact. Knocked the disk out. Reconnected drain hose and tested unit. During service noticed that the kick plate was missing and the insulation blanket was missing .Order parts for CX Unit working as designed. No water leaks observed during service.; ordrng 1 W10827631 (Access panel) and 2 WPW10503548 (Fastner)s and 1 W10896113 (Insulation blanket)

Arrived on site for a washing machine that is making a knocking sound as it goes into a spin. Inspected unit and work area. Ran unit through diagnostics and did not find any stored error codes. Ran the unit through an auto test in the unit ran as designed. Were on the unit through a high-speed spin and the unit ran as designed. Did notice that the unit was unlevel and leaning to the right where the tub was pressed up against the side wall. Did adjust the feet to level out the unit but did advise the customer that there were no issues that I could see with the unit. The unit is working as designed. Call complete.

"Arrived on site for a refrigerator that is not cooling properly. Inspected unit and work area. The customer advised that they had lost power this morning at 4 oclock and were not expecting power until later this afternoon. They did advise that a day after they called, the unit began to cool as designed. They did not know if there was still an ongoing issue with the unit or not but since they had no power they couldnt tell whether or not the unit would still work once the unit was powered back on. Luckily, power was returned to the customers unit prior to my departure. I did find the unit compressor kick on an attempt to cool. Ran the unit for 15 minutes and did find the unit continuing to cool down. I did explain to the customer that because the unit is working at this time, I could not verify what initially caused their issue. The unit is now working as designed. Call complete."

"Arrived on site for a range where the burners do not work properly. Inspected unit and work area. The customer advised that none of her burners really work properly as she has had issues with all burners staying at the proper temperatures. The customer pull out a pan to tear up some water. Found at the pan that she gave me it was not flat and rounded. Had the customer show me the other pans that she typically uses and found all of them not properly flat to touch against the security safety button. I did advise the customer that this unit requires that you have a flat surface for your pants because it is not going to function properly otherwise. Tested all the burners and found all working as designed except for the right rear burner. found the element not even attempting to turn on. I called Whirlpool Safety Team and spoke to David SR# 7734259745. He advised that based on the current information, whirlpool would not cover the repair and the customer would need to purchase new cookware for the unit. The customer advised that she did not wanna proceed forward with repair if whirlpool was not gonna cover it because she does not like this unit anyway and were just referred by her self in the unit. Call complete."

"Arrived on site for a dryer that is not starting any cycles. Inspected unit and work area. Confirm the customers complain and found wants the unit was started in the time start coming down, the basket was not spinning. Disassembled the unit and found the thermal fuse blown. I called Whirlpool tech line and spoke to Chris SR# 7734367381. He advised to go ahead and replace the thermal fuse in to measure temperature coming out of the exhaust. Found temperatures ranging from 164?F down to 131?F. I was advised this was good measurements and the issue would have to be we ventilation out of the home. Was advised to have the customer contact a vent cleaning service. Call complete."

Arrived on site for a refrigerator that is leaking water from the bottom of the freezer door onto the floor. Inspected unit and work area. Did confirm that there was ice buildup in the evaporator drip pan. Steamed out the ice and removed the clog out of the drain tube in the back of the unit. Ran water through and the unit is now working as designed. Call complete.

"Arrived on site for a washing machine that is not spinning out clothes. Inspected unit and work area. The customer advised at the unit on a wash cycle completely stopped draining and would not allow the letter to unlock. I did confirm the customers complaint and attempted to turn the unit on. Found the unit would not turn on but could not hear the drain pump running. Measured resistance through the drain pump and found that the drain pump it shorted.

"Arrived on site for a washing machine that is still having a drain issue. Inspected unit and work area. Did you from the customers complaint and found one of the wires on the drain pump connector separated from the actual connector. Fixed the connector and was able to drain the unit. Once the unit was fully drained, the unit stuck its self into the drain and would not Start draining until the unit was unplugged. A power cycled the unit several times and blew through the pressure hose. Found no blockage. Found the unit was still draining with the pressure hose removed from the control. The unit will need a new control for repair. Ordering the part but the office will need to contact the customer about a return date due to an out of stock and PSP item.; ordrng 1 W11419171 (Control)"

Arrived on site for a dishwasher that has a service pointer for a heating element replacement. Inspected unit and work area. Disassembled the unit and went to replace the heater. Found the heater in the box was missing but the box had the correct part number. Re-ordering the heater and the office will need to contact the customer about a return date due to limited parts availability.; ordrng 1 W11537778 (Heater)

Arrived onsite for oven intermittently heating. Sometimes does not heat at all. Upon arrival test unit 3 times and ignitor will not glow. Got 120 at ignitor. Resistance on ignitor is out of range. Need to replace ignitor. Replaced ignitor and unit operates as designed. Job complete

Arrived onsite for Too Cold in Freezer . Upon arrival inspected unit and found frost build up in FC cavity as well as top of FC door. Found 8long 1/4 in gap on bottom of RC right corner and 4 long of 1/16 inch o right side of Rc. Called techline for assistance. Submitted pictures via text to techline. Tech stated that there is no repair for me to make at this time. He is submitting case to engineering department Tech gave SR #7734370782

Arrived onsite for Not Filling or Long Fill Times . Upon arrival ran diagnostics and unit would go straight to draining continuously. Found error code F1-E1 control fault. Need to replace control. Replace control. Test unit and unit operates as designed. No leaks present at this time. Job complete

Arrived onsite for Ice maker not producing ice. Upon arrival found ice bin empty and no water in tray. Got good water pressure at supply. Reset icemaker to run harvest. Unit is now receiving water. No leaks present at this time. Job complete

"Arrived onsite for Not Operating or Won't Start . Upon arrival error F7-E1 tachometer missing or wrong signal, Is displayed on screen. Replaced actuator with truck stock. Test unit on a quick cycle with load of clothes.Unit operates as designed . No leaks present at this time. Job complete"

"Arrived onsite for customer states'The dishwasher initially stopped in between after 1 hour of washing and we had to manually press the start button again After that the buttons stopped working. Now after a day or two, we are able to operate the dishwasher again but the lights on the LCD do not show.Also, once the dishwasher finishes, it used to show CLEAN in the LCD. which is not showing now and all the lights go off in the LCD once the cleaning is finished . Upon arrival ran diagnostics and got F3-E3 owi failure.also found a couple of ui buttons are hard to push and lights intermittently blink. Also found failed filter.need to order owi sensor, ui, filter. ### ; ordrng 1 W11028325 (UI) and 1 W11084121 (OWI Sensor) and 1 W10872845 (Filter)"

"Arrived onsite for call back for same issue, Ice maker not producing ice.. upon arrival the ice bin made a few small pieces f ice since last visit. Tried running a harvest test and unit would only reset intermittently. Also found frozen fill tube. Ordering icemaker and valve. ###.; ordrng 1 W11455232 (Icemaker) and 1 W11455388 (Valve)"

Arrived on site for a dryer needing to be cleaned. On arrival the customer stated they wanted a lint cleaning. I cleaned the unit and then test it. I found it working as designed.

"Arrived on site to install previously diagnosed parts. I installed the valve housing, stator, and rotor. I then test the unit. I manually activated high spin and ran a diagnostics cycle to find them running as designed. I activated the unit with the valves exposed and verified the unit was no longer leaking. I then ran a quick cycle and found the unit running as designed. Call complete."

Arrived on site for a cooktop with broken regulator. Installed new regulator. Unit is now as designed. Call complete.

"Arrived on site for a washing machine that was excessively bouncing around during the cycle. On arrival the customer stated they were washing towels or sheets on the quick cycle and they found it would bounce the tub around, would cause the unit to move, and would be very loud. I put the unit into diagnostics mode and found stored error code F0E2 for over suds. I then manually activated spin and agitate to find it working as designed. I ran a diagnostics cycle and found it ran through as designed. I then tested the suspension and found it good. I gained access to the bottom of the unit and found no sign of any issue. I could not replicate a failure and found the unit working as designed at the time of service. I found that the unit would work as designed when the customer washed things like shirts or shorts on quick cycle. I informed the customer that it is most likely due to over loading and washing bulky items on the wrong cycle. I walked the customer through proper loading per the user care guide.

"Arrived on site for a washing machine not spinning out water from clothes and now making a loud thumping noise prior the last service. I put the unit into diagnostics mode and found no stored error codes. I then ran a diagnostics cycle and during the spin I heard an abnormal click, but no abnormal thumping. However, I found it still ramping to a good spin speed. I called techline and spoke to Rick and received SR# 7734368943. Rick recommend running a quick cycle with clothes in it to try and observe the failure. If issue was found then to replace console. I ran the cycle and found the unit started thumping abnormally loud on the ramp up. Upon further inspection I found the tub would only thump the right side of the chassis. I found the back right side shock sagging more than the rest. Due to this we will replace the two right side (from the front) shocks again. I am also ordering the console to install. ###. ; ordrng 1 W11325572 (Console) and 2 W11545322 (Shock)s"

"Arrived on site and inspected washer and did not find any saved error codes and all functions are working in diagnostic cycle. Customer is experiencing unbalanced load and discussed correct loading procedure and detergent usage. No further repair is required at this time, job complete"

"Arrived on site and inspected refrigerator and found door switch is broken. After replacing switch light is on, Job complete"

"Arrived on site and inspected refrigerator and found noise customer is describing is compressor on startup. Replaced start device. Explained that this is normal also discussed several other possible noises that might be heard while refrigerator is running. Refrigerator is operating as intended, job complete"

"Arrived on site and inspected refrigerator and found rails are broken in freezer. Replaced both and freezer door is now closing properly, job complete"

"Arrived on site and inspected dryer and found it is heating properly but airflow is showing restricted on airflow meter, took one picture. Removed vent hose from rear of dryer and airflow is now working properly. No further repair is required at this time, job complete"

"Arrived on site and inspected washer and did not find any saved error codes and all functions are working in diagnostic cycle. Customer is experiencing unbalanced load and discussed correct loading procedure and detergent usage. No further repair is required at this time, job complete"

"Test 56 shows error E2 motor lost position, Icemaker does not cycle on test 57 and gives 02 error. Ran test 45 and water fills icemaker properly. Will need a new icemaker to complete repair; ordrng 1 W11483245 (Icemaker) and 1 W11087201 (Fill tube heater)"

"Arrived on site and inspected refrigerator and found compressor will run for five seconds and then stops. Compressor service temperature is 115?, spoke with SW parts will be ordered for sealed system. See sticky notes for further details.; O-emld tckt"

Arrived onsite for dishwasher not washing dishes. Upon inspection I found a wash motor not running code and after testing the unit the motor did not come on. I replaced the Sump&motor and tested the unit and found that the unit is now operating as designed. No leaks Job complete.

Arrived onsite to perform Heating Element - SP W11540964 - Special Project S17304 - PRE-ID Heater Bushing W11537778 - . . . After doing so I tested unit and found unit as designed. No leaks job complete.

Arrived onsite for dryer that would not tumble/heat. Upon inspection I found that the thermal fuse had popped. I installed new fuse WP3392519. and tested unit and found unit operating as designed. Job complete.

Arrived onsite for a dryer that is not operation. Upon inspection I found that the belt had broken tensioner pulley received. I installed a dryer repair kit and tested the unit and found unit operating as designed. Office to charge card on file. Job complete.

"Arrived onsite for refrigerator that is not making ice upon inspection I found that the fill tube and the cup where frozen I found Service Pointer #: W11560805 and I am ordering IM,fill tube, and water valve. ###.; ordrng 1 W11397137 (Ice maker) and 1 W11395429 (Fill tube) and 1 W11455388 (Water valve)"

Arrived on site to test unit for front panel dented. Found dents on from panel replaced panel test unit and unit test good job complete.

Arrived on site to test unit for oven not igniting. Test unit and found glow igniter giving 2.85 amps but valve not opening. Will need new valve

Arrived on site to test unit for unit not draining. Pulled unit out and found pinched drain hose. Secured drain hose test unit and unit test good job complete.

Arrived on site to resolve heating element due to special project. Replaced element test unit and unit test good job complete no leaks present at this time.

Arrived on site to replace heating element due to special project. Replace element test unit and unit test good no leaks present job complete.

Arrived on site to replace fan blower. Replaced blower test unit and unit test good job complete.

Arrived on site to test unit for unit not washing. Test unit and unit working as designed at this time. Advised customer it could be the sump and motor over heating. Job complete.

Arrived on site to test unit for unit not starting. Test unit and found shorted keypad and control board.

Arrived on site to test unit for center front burner not igniting. Found cracked cooktop on top of center front burner. Will order new cooktop and will replace cooktop and burner and infinite switch; ordrng 1 W11051486 (Cooktop black)