We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Lago Vista, TX 78645
Vincent
Job Details:
09/19/2022
"Arrived on site for refrigerator, inspected unit and work area. CX complaint was leds not working. Inspected the led control and found it good. Found the front left led module under the icemaker housing flickering. I used my jumper and to test and make sure thats the only one out. Replaced the module with new one and its covered under the warranty. Unit is now operating as designed. No leaks where observed. Job completed."
We serviced a
MAYTAG WASHER
Model MVWC500VW1
Near Austin, TX 78746
David S
Job Details:
09/19/2022
Arrived on site for washing machine filling slow. I inspected the unit and work area. I found the cold valve filling slow. I tested the water flow from the wall and found good pressure. I replaced the water valve and tested it. It is now working as designed. Job complete.
We serviced a
WHIRLPOOL FREEZER
Model WRF767SDHZ00
Near Lago Vista, TX 78645
Vincent
Job Details:
09/19/2022
"Arrived on site for refrigerator, inspected unit and work area. CX complaint was that FC light and RC top lights stopped working. Inspected unit and found freezer door switch getting stuck and found FC module out. Replaced module and switch and unit is now operating as designed. No leaks where observed. Job completed."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Austin, TX 78732
David S
Job Details:
09/19/2022
Arrived on site to install previous diagnose parts. I gained access to the fc led and replaced it with new. I replaced the fc gasket as well. The lights are coming on and the freezer is sealing. Job complete.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Meadowlakes, TX 78654
Vincent
Job Details:
09/19/2022
"Arrived on site for dishwasher, inspected unit and work area. CX complaint was that DW would not dry. Ran diagnostics and tested amp draw on heating element. Unit did not have any error codes and amp draw was holding around 7.2. CX stated she just switched from pods to liquid and is using drying agent now. Adjusted drying agent level down to one from two to prevent excessive suds. Unit is working as designed. No leaks were present during time of service. Job complete."
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS4
Near Pflugerville, TX 78660
Cliff
Job Details:
09/19/2022
Arrived on site to diagnose a range with an oven not heating properly. Tested all parts and components and found no failures to unit at this time. Advised customer on findings and no further repairs needed.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Hutto, TX 78634
Cliff
Job Details:
09/19/2022
Arrived on site to diagnose a dishwasher that is not cleaning properly. Found owi not registering properly and replaced it. Tested unit and found all is functioning properly at this time and no leaks were found at time of service.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near New Braunfels, TX 78130
Andrew
Job Details:
09/19/2022
"Arrived on site and replace heating element per special project. Unit working as designed, no leaks detected. Job complete."
We serviced a
MAYTAG DRYER
Model MED7230HW2
Near New Braunfels, TX 78132
Andrew
Job Details:
09/19/2022
Arrived on site to test unit for console loosing power. Unable to replicate issue. Replaced console as a precautionary. Unit working as designed. Advised to download Maytag app and get units connected to Wi-Fi. No leaks detected. Job complete.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS09
Near Hutto, TX 78634
Cliff
Job Details:
09/19/2022
Arrived on site to diagnose a microwave that is making unusual noise. Found screws in bottom plate not tight causing rattling. Tightened screws and all is working properly at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX988SIBM01
Near Marion, TX 78124
Andrew
Job Details:
09/19/2022
"Arrived on site to test unit for no ice production. Found ice maker ran full harvest with no issues. No stored error codes. Fill tube and fascia heater received proper voltage(120vac). FC and RC temps were correct. All air flow motors working. Tried to fill ice maker but water did not reach ice maker. Found fill tube was obstructed. Removed water line and ran test on valve. Valve opening and closing as designed. Removed obstruction and ice maker filled properly. Found water pressure at 78psi. Spoke with CS and adjusted temps to recommended 3degrees in FC and 37 in RC. Advised customer to monitor. If issue persists recommend main single inlet valve, pressure regulator and fill tube heater. No leaks detected. Job complete."
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ1
Near Austin, TX 78724
Matthew
Job Details:
09/19/2022
"Arrived onsite for potential gas leak. Upon arrival inspected unit. Customer stated unit emits smell when oven in use and cooktop burners do not ignite. Tested all cooktop burners and all are functioning properly. Ran bake cycle at 350 degrees and unit heated fine. Tested multiple times and could not duplicate any issues. While talking to customer, may have been an instance of spillover causing burners to temporarily not ignite. Unit is functioning properly. No gas leak detected. Gas smell coming from ignition process. Customer is used to electric range. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Austin, TX 78723
Matthew
Job Details:
09/19/2022
Arrived onsite for unit filling slowly. Upon arrival inspected unit. Found low water supply from hot water. Supply is sputtering. Tried disconnecting supply but will need plumber to resolve issues. Water supply will not shut off in either direction. Unit is functioning properly. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model MDB8959SKZ0
Near Austin, TX 78739
Leonardo
Job Details:
09/19/2022
Arrived on site to replace 3rd rack wheels. Replaced both side test unit and unit test good job complete.
We serviced a
WHIRLPOOL COOKTOP
Model JGD3536GS00
Near Austin, TX 78739
Leonardo
Job Details:
09/19/2022
Arrived on site to replace cooktop. Replaced cooktop test unit and unit test good job complete.
We serviced a
MAYTAG DRYER
Model MGDB835DW4
Near Austin, TX 78747
Scott
Job Details:
09/19/2022
Arrived on site for dryer making a squealing noise. Found idler pulley wheel locked up and causing belt to squeal . Replaced idler with truck stock ( part W10547287 ) . Unit also had a lot of lint build up . vacuumed out unit . Unit is performing normally. Advised customer to have exterior vent cleaned
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS06
Near San Marcos, TX 78666
Luis
Job Details:
09/19/2022
"Arrived on site. Temp reading 0? at time of visit,found defective tracks on ice bin,added adhesive to liner gaps,replaced glide assembly tested drawer operation good."
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0HS02
Near Andice, TX 78628
Gerry C
Job Details:
09/19/2022
"BT Arrived on site to replaced pre diagnosed parts. I replaced the oven door, and the console. After replacement unit operates as designed."
We serviced a
WHIRLPOOL FREEZER
Model KRSC703HPS00
Near Leander, TX 78641
Gerry C
Job Details:
09/19/2022
"Arrived to instal previously diagnosed and ordered part. Prior to installation, I found the mullion badly mis-molded and preventing both the FC and RC doors from closing fully at the lower mullion to front border area and the upper FC was gapped as well. I contacted the MFG, tech Robert and advised of my findings. The unit is non-repairable due to an incorrectly manufactured cabinet/liner and will be referred to Customer Service at 800-253-1301, file# 7734620401. No leaks observed during service."
We serviced a
WHIRLPOOL WASHER
Model WTW5100HC3
Near Leander, TX 78641
Gerry C
Job Details:
09/19/2022
BT arrived on site to inspect washer. CX has concerns washer lid closes too fast and easily. I replaced dampened hinges. Unit required basket centering within chassis. I recalibrated the unit. No leaks found during service.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Andice, TX 78628
Lou
Job Details:
09/19/2022
"Arrived on site to inspect dishwasher error codes. Upon further inspection, I found the display showing error code F2E2. I attempted to place the unit in diagnostics and it failed. I cycled power to the unit and attempted again and it continued to fail. I removed the outer door panel and inspected the user interface (UI) and found no debris on it to cause it to fail. I replaced the UI and retested and unit is operating as designed. I made recommendations for use and care, as well as, detergent and rinse aid use. No water leaks observed during service, job completed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model MFI2570FEZ09
Near Gatesville, TX 76528
Jonathan M
Job Details:
09/19/2022
"Arrived on site to install previously diagnosed parts. Inspected unit and work area. Replaced the separator, dispenser motor, spacer, impeller, and damper gasket. Reassembled the unit and tested the unit and crushed and cubed ice. Found the unit dispensing ice as designed. Found the icemaker completing a full harvest immediately after getting everything in so the unit is now working as designed. Call complete."
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near McGregor, TX 76657
Jonathan M
Job Details:
09/19/2022
Arrived on site for a dryer that will heat but will not turn the drum. Inspected unit and work area. Tested the unit and found the motor turning but the drum not turning inside of the dryer. Remove the top cover and the front panel and found the dryer belt had snapped in half. Tested the rollers and found the rollers also needing to be replaced. Replaced both rollers and dryer belts and tested the unit. The unit began to work and operate as designed. Call complete.
We serviced a
AMANA WASHER
Model NTW4516FW
Near Moody, TX 76557
Jonathan M
Job Details:
09/19/2022
"Arrived on site for a washing machine that is not advancing. Inspected unit and work area. Confirmed the customers complaint and ran the unit three diagnostics. Found an F8 E1 (low/no water detected during fill) error code. Tested the valves and found both hot and cold water valves working properly. Checked the drain and found the PVC pipe the customer has this draining into is approximately 8 inches to a foot off the ground. I explain to the customer that the reasoning why theyre having this issue is because as the unit is filling past 1/3rd to half the way up the tub, it is siphoning out of the drain due to the water pressure inside of the washer. Advised the customer to get an extension for the drain pipe and to keep it at least 36 inches off the ground. The unit is working as designed. Call complete."
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Austin, TX 78752
Wesley
Job Details:
09/19/2022
Arrived onsite and found shift actuator not shifting properly causing issues. Replaced the shift actuator. Unit is now operating as designed.
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Austin, TX 78754
Wesley
Job Details:
09/19/2022
Arrived onsite for not running properly on sensor cycles and found the thermostat out of range. Replaced the thermostat with truck stock. Unit is now operating as designed. All checks good. Advised customer that using timed dry feature can be useful for consistent drying of heavier loads. ; used 1 WP8577274 (Thermostat) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Austin, TX 78723
Wesley
Job Details:
09/19/2022
Arrived onsite and found that the doors on the unit with the matching model and serial were cosmetically correct and able to be cleaned to restore like new finish.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32519HZ7
Near Austin, TX 78724
Wesley
Job Details:
09/19/2022
Arrived onsite and found loose connection at the cavity thermostat. Secured connection. Unit is now operating as designed without the power supply intermittently cutting out.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS09
Near Manor, TX 78653
Wesley
Job Details:
09/19/2022
SR#7734585102 arrived onsite and found failed mag with no dangerous or unusual damage. Reported to safety. Recommended replacing mag cap and diode. Completed repair. All checks good.
We serviced a
WHIRLPOOL COOKTOP
Model KCED600GBL01
Near Round Rock, TX 78681
Kimo
Job Details:
09/19/2022
Arrived onsite to installed new glass cooktop. Upon inspection I did find that the cooktop was warped. I replaced the cooktop top and installed new knobs and tested the unit and found it operating as designed. Job complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Round Rock, TX 78681
Paul
Job Details:
09/19/2022
"Arrived onsite to install previously diagnosed and ordered parts. No ice was present in freezer. R/R lower freezer bin and tested. Operational test good, no leaks observed during service. Call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near San Marcos, TX 78666
Luis
Job Details:
09/19/2022
Arrived on site for a defective compressor. Replaced compressor and drier vacuumed system down unit kept vacuum recharged system to manufacture spec powered unit on checked low side pressure good.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF954CIHB01
Near Austin, TX 78749
Luis
Job Details:
09/19/2022
"Arrived on site. Found high water pressure installed reducing valve tested water dispenser unit working as designed. ; used 1 W10786952 (Valve), and 1 8212547RP (Tube) from stock"
We serviced a
KITCHENAID REFRIGERATOR
Model KBSN608ESS01
Near Austin, TX 78735
Luis
Job Details:
09/19/2022
"Arrived on site for loud noise. Diagnosed loud vibration noise from compressor compartment,removed cover found discharge tube vibrating against cabinet,adjusted tubing noise no longer present. Repair covered by manufacture 2 year warranty"
We serviced a
WHIRLPOOL COOKTOP
Model WCG55US0HS00
Near Bastrop, TX 78602
Joe Z
Job Details:
09/19/2022
Arrived onsite to install previously diagnosed parts. Replaced gas valve. Test unit and unit operas designed. No leaks present at this time. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Austin, TX 78744
Joe Z
Job Details:
09/19/2022
"Arrived onsite for Neither Spray Arm is Working . Upon arrival ran diagnostics and got error codeF4-E3 motor not running. Ran auto test and unit fills correctly. Motor is receiving voltage,just not energize. Need to replace sump and motor. Replaced sump and motor and test unit. Unit operates correctly. No leaks present at this time. Job complete"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Austin, TX 78744
Joe Z
Job Details:
09/19/2022
"Arrived onsite for Oven Odor and Smells . Upon arrival inspected unit and found DO NOT USE TAG from gas company with gas supply valve shut off. Checked for gas leaks with electronic sniffer at all4 cooktop burners as well as oven . No leaks were present. Pulled unit from wall to check supply hose,connectors and valve. Sniffer Found leak coming from valve area. Used bubble leak detector to pinpoint leak. Found leak at tubing connector between valve and regulator. The connector was not secure. Secured tubing connector and test unit with bubble leak detector. Unit is no longer leaking. Test unit by preheating oven to 350. Unit operates as designed. Job complete"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS4
Near Leander, TX 78641
Gerry C
Job Details:
09/19/2022
"BT arrived on site to inspect range. I checked all gas connections with bubble leak detector and found no leaks. Further discussion with CX said leak came while using bake setting and during heavy use. I found the air shutter on bake element to be adjusted incorrectly causing a incorrect gas mixture. This also causes a loud sounding bake burner due to the very lean air/fuel mixture. I adjusted the air valve and and now the burner is quiet and efficient with no use of excess gas. After adjustment, I tested with bake and all burners running simultaneously and there was no raw gas odor. I advised the CX to always utilize the vent fan during any operation. No gas leaks detected during service."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ02
Near Austin, TX 78725
Joe Z
Job Details:
09/19/2022
Arrived onsite to install previously diagnosed parts. Replaced right side RC door hinge. Unit is operating as designed. Verified ice bin is full per previous visit. No leaks present at this time Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ09
Near Killeen, TX 76543
Tyler
Job Details:
09/19/2022
Arrived on site for refrigerator leaking from filter housing. Upon arrival confirmed issue. After further testing I found filter head not sealing to filter correctly. Replaced head asm and tested unit. Found no leaks and unit functioning as designed. Call complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Liberty Hill, TX 78642
Lou
Job Details:
09/19/2022
"Arrived on site to inspect dishwasher not cleaning properly. Upon further inspection, the customer handed me a spring that had fallen out of the dispenser and advised the unit is not cleaning their dishes well and is leaving soap at the end of the cycle. I found an unused detergent pod in the dispenser and removed it. I placed the unit in diagnostics showing no error codes. Continued with testing and monitored the amp draw to the components. I found the unit operating as designed minus the dispenser. I found suds at the end of testing as well. I removed and replaced the dispenser and retested and unit is operating as designed. I made recommendations for use and care, as well as, detergent and rinse aid use. No water leaks observed during service, job completed."
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Austin, TX 78736
Leonardo
Job Details:
09/19/2022
Arrived on site to replace heating element from special project. Replaced element test unit and unit test good job complete.
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ2
Near Briarcliff, TX 78669
Leonardo
Job Details:
09/19/2022
Arrived on site to test unit for not light. Test unit and found wire disconnected. Also found breaker for range is also attached to the disposal. Advised customer Whirlpool recommens the unit to be in its own dedicated circuit.
We serviced a
JENN-AIR MICROWAVE
Model JMC2427DS01
Near Spicewood, TX 78669
Leonardo
Job Details:
09/19/2022
Arrived on site to replace console. Replaced console test unit and unit still not working. Unit giving F1E6 still called Techline and they advised to get electrician to check unit under a load. Everything has been replaced at this time SR#7734616370
We serviced a
WHIRLPOOL MICROWAVE
Model WOC54EC0HS04
Near Dripping Springs, TX 78620
Leonardo
Job Details:
09/19/2022
Arrived on site to test unit for temp not being correct. Replaced sensor and showed customer how to calibrate the unit. Customer will use the unit to make sure it working correctly. Job complete.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Blanco, TX 78606
Kevin
Job Details:
09/19/2022
"Arrived on site and Customer is still experiencing water dripping down the front fa?ade of the icemaker box. Set refrigerator into a diagnostic cycle and found saved error code E2 on test 56. Ran 57 and icemaker dispensed properly, ran test 45 and it filled properly. Spoke with techline and they recommended replacing dual valve in fresh food ceiling. If issue continues tech line will need to be contacted on every visit moving forward 7734613625."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Austin, TX 78703
Luis
Job Details:
09/19/2022
"Arrived on site for no ice in fresh food compartment icemaker. Ran diagnostics E5 error code diagnosed a defective thermistor on icemaker,replaced icemaker,power cycled unit ran icemaker test passed,icemaker ran harvest test and filled with water"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Austin, TX 78722
Matthew
Job Details:
09/19/2022
Arrived onsite for ice maker not functioning. Upon arrival inspected unit. Found not power to unit. Notified customer that a power supply would be needed to insure a good repair can be made. Customer will need reschedule when power is restored.
We serviced a
WHIRLPOOL RANGE
Model KFGC558JSS01
Near Austin, TX 78722
Matthew
Job Details:
09/19/2022
Arrived onsite for front burners not igniting properly. Upon arrival inspected unit. Found delayed ignition with 3 front burners. Upon further inspection found front center burner cap was on left front burner and vice-versa. Switched caps and center burner ignites without error. Right and left front burners needed adjustment to allow better flow. Made Burner adjustment and now all burners are igniting properly. Invited customer to test. Customer was satisfied. Job complete
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Austin, TX 78757
Kimo
Job Details:
09/19/2022
"Arrived onsite for a washer that is Not completely filling with water, flashing sensing, doesn't agitate, then drains the water. Upon inspection I found that the unit would not let me get into diagnostics mode. Upon further inspection I found that all harness connections in the unit were good. I found that the drain hose was not in a standpipe and was laying on the ground and as the unit would fill with water a Siphon would be created and the unit would not fill properly causing the issue. I Adjusted the hose and tested unit in diag mode and found the unit operating as designed. Job complete."
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Pflugerville, TX 78660
Kimo
Job Details:
09/19/2022
Arrived onsite for washer that wont Agitate. Upon arrival I put unit into diagnostics mode and ran cycle and found that the unit was not agitating properly. I check the shit actuator and found that it was not connected to the cam arm. I replaced it and tested unit and found unit operating as designed. No leaks found. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ01
Near Pflugerville, TX 78660
Kimo
Job Details:
09/19/2022
Arrived to install previously diagnosed. Upon arrival I installed new con and ui. And when to test unit and found that the unit burnt up the new control. I removed the new control and installed the old one same with the ui. Upon further inspection I found that the was some damage to the harness inside the chassis where we can not reach to repair due to a lighting strike. Did not collect dance due to these factors. Job complete.
We serviced a
AMANA WASHER
Model NFW5800HW3
Near Round Rock, TX 78681
Paul
Job Details:
09/19/2022
"Arrived onsite to inspect washer not spinning during some cycles. Placed unit into diagnostics and Ran a test cycle. Unit went into a spin cycle during test. I went into settings and the unit was set to no spin when set to color cycle. I ran a color cycle. Operational test good, light suds during test. Advised CX on detergent use. No leaks observed during service. Call complete."
We serviced a
GE MICROWAVE
Model JVM6172SK2SS
Near Cedar Park, TX 78613
Paul
Job Details:
09/19/2022
Arrived onsite to inspect microwave not heating. I tested the capacitor and it was good. I volt tested the harness to the transformer and it read 120. I ohm tested the magnetron and it read as good. Tested unit with power and unit is still not heating properly. Retested magnetron and now it is not reading properly. Magnetron is bad. R/R magnetron and tested. Operational test good. Call complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Cedar Park, TX 78613
Paul
Job Details:
09/19/2022
Arrived onsite for a refrigerator with the ice sticking in the chute and the water dispenser dropping. I found the ice door not sealing correctly causing moisture to build up in the chute and ice to stick to the sides. I found the water dispenser tube not clipped in correctly allowing water to siphon out of the tube after dispensing water. I replaced the ice door and corrected the tube. I went over ice use and dumping the bin after two weeks if all the ice hasnt been used with the customer. Call complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ03
Near Cedar Park, TX 78613
Paul
Job Details:
09/19/2022
"JM: Arrived onsite to install previously diagnosed and ordered parts. R/R control and tested. Ice maker harvested and filled with water. Operational test good, no leaks observed during service. Call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Round Rock, TX 78665
Maurice R
Job Details:
09/19/2022
Arrived onsite for refrigerator freezing upper shelf. On inspection the freezer was 9? and the refrigerator was 44? tested the RC thermistor and it was 5.7K= 46? actual was 44? FC 14.7k=13? actual was 9? tested the damper it was operating as designed. Squared the chaise of the unit. Set the defrost to ever 8 hrs. Temps are set FC 0 RC 37. CX will call if the unit still having issue. No water leaks detected during the inspection
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Georgetown, TX 78626
Maurice R
Job Details:
09/19/2022
"Arrived onsite for dishwasher not drying. On inspection found The unit had no rinse agent,explained to CX how the new dishwasher do not dry like the old unit did and that rinse agent helps dry dish and help dispense the water off the walls of the dishwasher. No leaks detected during time of service."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Austin, TX 78717
Vincent
Job Details:
09/19/2022
"Arrived on site for dryer, inspected unit and work area. CX complaint was that the dryer had zero heat. Inspected dryer and unit failed vent test. Advised CX to get vents cleaned. Opened dryer and found thermal cutoff open; ordrng 2 W10900067 (Cut off)s"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF954CIHZ03
Near New Braunfels, TX 78133
Andrew
Job Details:
09/19/2022
Arrived on site to test unit for not cooling in RC department. Tested thermistors in diagnostics and directly from connections and got same readings at 67 degrees. tested FC thermistors and were also in range at control and directly from connections. RC temps were 67 degrees and fc temp was 22 degrees but ice bin was full and not melted. All air flow fans working as designed. In service test 40 found everything working as designed. Spoke with Techline with finding and advised to replace compressor and tap into lines to get better readings. Ordering recommended parts from rd home along with precautionary parts. 1 W11099748 (FC evap) and 1 W11592010 (Compressor) and 1 W11109499 (Non-UV drier) and 1 W11575001 (3-way valve) and 1 W11443923 (Suction tube) and 1 W10735062 (Process tube) and 1 W11533212 (Control kit)
We serviced a
WHIRLPOOL FREEZER
Model WZF34X18DW04
Near Copperas Cove, TX 76522
Tyler
Job Details:
09/19/2022
Arrived on site for freezer leaking. Upon arrival confirmed confirmed issue but also found unit not cooling. Customer stated ui lights stoped working. After further testing I found ui control box had large burn mark. Found stable power connection and no resistance failures with heater or compressor. Based on customer observation prior to issue its possible unit had defrost issue before failure. ; ordrng 1 W11496873 (Control box) and 1 WPW10383615 (Thermistor (evap)) and 1 WPW10384183 (Thermistor (rc))
We serviced a
KENMORE DISHWASHER
Model 665.14743N510
Near Austin, TX 78739
Leonardo
Job Details:
09/19/2022
Arrived on site to test unit for unit not washing. Test unit and found bad sump and motor. Ordering sump and motor ; ordrng 1 WPW10605058 (Sump and motor)
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Austin, TX 78753
Wesley
Job Details:
09/19/2022
Arrived onsite and replaced latch for unit responsive but unable to start cycle. Symptom unchanged. Ordering control and drain pump to repair. Unable to access error code translation using available tech sheets. ; ordrng 1 W11626074 (Control) and 1 W11399437 (Pump)
We serviced a
WHIRLPOOL MICROWAVE
Model WOC54EC0HS20
Near Manor, TX 78653
Wesley
Job Details:
09/19/2022
Arrived onsite and found unit is having UI glitching. Customer had already power cycled unit. Ordering the UI to repair. ordrng 1 W11600630 (Console)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHW08
Near Bastrop, TX 78602
Joe Z
Job Details:
09/19/2022
"Arrived onsite for Not Cooling - Both Sections. Upon arrival inspected unit and found evaporator covered in ice. Ran diagnostics and all fans, compressor and sensors checked out good. Forced heater and will not energize. Need to order control, ui, heater, harness, ice maker; ordrng 1 W11405276 (Harness) and 1 W11449482 (Control) and 1 W11169239 (UI) and 1 W11546610 (Heater)"
We serviced a
FRIGIDAIRE FREEZER
Model FCFS201LFB4
Near Georgetown, TX 78628
David Z
Job Details:
09/19/2022
"Arrived on site to diagnose standalone freezer that is no cooling. Customer said unit started making noise and stopped cooling. Ran unit and could hear the compressor scraping and what sounds like a bearing banging around / rolling around inside the compressor. Compressor has failed. ordrng 1 216894100 (Compressor) and 1 297311300 (Evaporator) and 1 TJ90SF8404 (Non WP access Valve) and 1 Wpw10143759 (Drier)"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Austin, TX 78704
Matthew
Job Details:
09/19/2022
Arrived onsite to replace previously diagnosed parts. Replaced sump and motor assembly and OWI sensor. Tested unit and found unit leaking. Inspected and found tub is dented in rear ( took pics) weld joint is broken and is leaking. Took pic of area. Will need to order and replace tub. Customer will be reaching out to KitchenAid to see if anything can be expedited ; ordrng 1 W11409866 (Tub) and 1 W11537778 (Heater) and 1 2hr (2 hr)
We serviced a
KITCHENAID RANGE
Model KSGG700EBS3
Near Austin, TX 78758
Kimo
Job Details:
09/19/2022
Arrived onsite for a range that is not sparking. Upon inspection I found that the harness was damaged.I am ordering a harness ; ordrng 1 W11454287 (HARNS-WIRE)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF130PAHB1
Near Georgetown, TX 78626
Maurice R
Job Details:
09/19/2022
Arrived onsite for dishwasher with no power. On inspection found that the breaker was tripped. I put the unit into diagnostics mode and found that water was turn off. Turn on water started test over and the pumps were caveating and no water was present in the dishwasher. Turn the unit off. Ordering parts. No water leaks detected during service.; ordrng 1 W10876537 (Drain pump) and 1 W10888591 (Pump assembly) and 1 W11175771 (Water inlet valve) and 1 WPW10195039 (Overfill switch) and 1 WPW10346525 (Overfill float)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHV00
Near Georgetown, TX 78633
David Z
Job Details:
09/19/2022
Arrived on site to diagnose refrigerator that isn't dispensing ice or water. Tested unit and found the paddle switch is barely making contact and has to be forced hard to get it to dispense. Ordering new paddle assembly to resolve ; ordrng 1 W10853387 (Dispenser Pad)
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0HS02
Near Georgetown, TX 78633
David Z
Job Details:
09/19/2022
"Arrived on site to diagnose oven that has unresponsive console. On arrival found unit stuck in powering up state. Power cycle does not resolve, attempted numerous times. Unit needs new console to resolve due to failed console. Customer has 2nd year builder warranty with Coventry homes, will need to contact WP for concession per SP. ; ordrng 1 W11296171 (Console)"
We serviced a
JENN-AIR FREEZER
Model JBZFL18IGX00
Near Austin, TX 78759
David S
Job Details:
09/19/2022
Arrived on site for Lights not working. I inspected the unit and work area. I found The upper switch not connected. I reconnected the switch and power cycled the unit. I still found no lights. I tested the bottom switch and found it working as designed. I found only 30 vac to the switch. I am ordering the hv control. The office will reschedule when we have eta on the parts.; ordrng 1 W11302062 (Hv control) and 1 W11233638 (Led control)
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM604KPS0
Near Austin, TX 78746
David S
Job Details:
09/19/2022
Arrived on site to possibly install previous diagnose parts. I replaced the dispenser. I found the unit already has the insulating shield. I ran the dishwasher and heard the grinding noise when the upper two rows are activated. I pulled the third row and spun the gears. I could hear some unusual noise coming from the assembly I am ordering the third row assembly. The office will reschedule when we have eta on the parts.; ordrng 1 W10830523 (Manifold third row) and 1 W10831864 (Third row jet tubes)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Lago Vista, TX 78645
Vincent
Job Details:
09/19/2022
"Arrived on site for refrigerator, inspected unit and work area. CX complaint was that unit had power, but not cooling at all. Tested temps and they where to hot. Found compressor locked up. Unit I will need a sealed system repair. Copper cap tube. Office will contact CX when parts are available. Leaks where observed during service. Unit is in garage, plz try to set appointment for morning.; ordrng 1 W11370574 (Compressor) and 1 WPW10143759 (UV DRYER) and 1 W11506635 (Access valve) and 1 Nitrogen (Nitrogen) and 1 R600kit (R600 Kit)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Pflugerville, TX 78660
Cliff
Job Details:
09/19/2022
Arrived on site to diagnose a dishwasher that is missing parts. Found kickplate and clips missing. Ordering needed parts and return date ; ordrng 1 W10827631 (Kickplate) and 2 WPW10503548 (Clips)s
We serviced a
WHIRLPOOL OVEN
Model WFE320M0EB1
Near Marble Falls, TX 78654
Lou
Job Details:
09/19/2022
"Arrived on site to install previously diagnosed and ordered parts. Per previous techs diagnosis, I removed and replaced the front left and right burner switches. In the process, I found both back burner switches were burnt (photos). I tested the burners and found they only operate on high heat. I removed and replaced the back right burner switch and inspected the burners. The burners are good. I tested the front left, right and back right burns and all are operating as designed. I am ordering the back left burner switch ; ordrng 1 WP3149404 (Back left switch)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS311SDHM08
Near Austin, TX 78723
Matthew
Job Details:
09/19/2022
"Unit in Second floor garage storage area. Upon arrival inspected unit. Unit is having defrost issues. Compressor is running and evaporator is frosting. Ordering control, UI and defrost sensor. ; ordrng 1 W11546609 (Control) and 1 W11203289 (UI) and 1 W11546681 (Harness) and 1 Defrostsensor (Parts research)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model MSS25C4MGZ06
Near Gatesville, TX 76528
Jonathan M
Job Details:
09/19/2022
Arrived onsite to install previously diagnosed parts. Inspected unit and work area. I removed the back cover and went to test the new compressor to make sure the new compressor would work. Found the new compressor would not allow the starting device to fit. Found the new start device located with the compressor would not work with the current compressor wire harness. Spoke to SR and was advised that we ordered the right part according to Marcone and to the part number that subs over but that Whirlpool had updated the subbed part number and will need to be reordered. I couldnt find the part number she sent but was advised to just order the part number and it would be taken care of. Ordering the correct compressor and the office will need to contact the customer to reschedule service due to an out of stock and PSP item. Please schedule for at least three hours on return trip.; ordrng 1 W11635510 (Compressor)
We serviced a
MAYTAG WASHER
Model MVWC465HW2
Near McGregor, TX 76657
Jonathan M
Job Details:
09/19/2022
"Arrived on site for a washing machine that is making a knocking noise during the spin cycle. Inspected unit and work area. The customer showed me a video of what she was hearing and it sounded like a knocking noise coming from a loose agitator. Did inspect the agitator and did not find any evidence of it being loose. Ran the unit through diagnostics in an auto test and through manual high-speed spin and could not replicate the issue. I called Whirlpool Techline and spoke to Scott SR# 7734617645. He advised me over to a service pointer (W11520474) that del with this issue. He advised if the unit could not replicate the sounds in diagnostics, the issue was with the triad on the control. Ordering the control and the office will need to contact the customer to reschedule due to limited parts availability.; ordrng 1 W11498797 (Control)"
We serviced a
KITCHENAID COOKTOP
Model KCGS350ESS00
Near Georgetown, TX 78628
David Z
Job Details:
09/19/2022
"Arrived on site to follow up on cooktop that had a sputtering middle valve when switching between simmer and normal flame. After experimenting with the valve/knob: if you move the knob very slow to where it's transitioning between the inner and outer orifices, flame can sputter out going in either direction. Tried adjusting the valve but saw no difference. Called tech line and spoke with Rich, who advised we replace that valve only. If no change occurs then this is working as designed, but valve needs to be replaced to verify. Return visit set for 9/23. ; ordrng 1 W11246817 (Valve)"
We serviced a
WHIRLPOOL DRYER
Model WGD9620HC1
Near Cedar Park, TX 78613
Paul
Job Details:
09/19/2022
"Arrived onsite to inspect dryer stopping midway through a cycle. I tested temperatures at the lint screen. Hi-cycle was 160 and the low-cycle was 130. Thermistors are out of range. Ordering inlet thermistor, outlet thermistor, sensor harness. CX has an extended warranty and the call needs to be switched over to an extended warranty dispatch per JA. Office to RS.; ordrng 1 W11396709 (Outlet thermistor) and 1 WPW10298258 (Sensor harness)"
We serviced a
WHIRLPOOL COOKTOP
Model KCGC506JSS00
Near Leander, TX 78645
Vincent
Job Details:
09/14/2022
Arrived on site for front right burner not working properly. Inspected unit and work area. Front right burner head would not ignite. Replaced front right burner head. Unit it working as designed. No leaks observed during service. Job complete.
We serviced a
WHIRLPOOL WASHER
Model WFW75HEFW
Near Austin, TX 78705
Wesley
Job Details:
09/14/2022
Arrived onsite and tested washer for noisy drain pump. Unit had no error codes and unit is quiet and operating properly in diagnostics advised customer on findings. Customer advised that unit noise was an electrical hum that came in and out periodically while the unit is in standby. Customer will record incident next time it occurs for diagnostic aid. All functions testing properly while onsite.
We serviced a
WHIRLPOOL RANGE
Model WGE745C0FS01
Near Austin, TX 78734
Leonardo
Job Details:
09/14/2022
Arrived on site to test unit for right front burner not working. Found bad burner replaced burner test unit and unit test good job complete.
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JS3
Near Bastrop, TX 78602
Matthew
Job Details:
09/14/2022
Arrived onsite for range not powering on. Upon arrival inspected unit. Unit non responsive and no display. Checked incoming supply voltage and found no voltage. Inspected further and found breaker was off. Established supply and tested. Unit is heating and operating properly. Tested all cooktop burners and oven function. Job complete
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW1
Near Kyle, TX 78640
Justin
Job Details:
09/14/2022
Arrived on site for a dryer with a physically broken component. Upon further inspection I found the door switch broken. I replaced the switch and test the unit. The unit is now working as designed. Call complete.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Bastrop, TX 78602
Matthew
Job Details:
09/14/2022
Arrived onsite for dryer not heating. Upon arrival inspected unit. Found unit would start and tumble but not heat. Inspected further and found failed cutoff. Replaced cutoff and tested. Unit is cycling and heating properly. Recommended customer have external ventilation cleaned to insure proper ventilation. Job complete
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCF72DKL04
Near Bastrop, TX 78602
Matthew
Job Details:
09/14/2022
"Arrived onsite for refrigerator leaking, not making adequate ice and door not closing properly. Upon arrival inspected unit. Pulled unit forward and found water underneath unit. Found that fill tube for Ive maker was not inserted into valve properly. Secured line and leaking stopped. This was also the reason the ice maker was making little ice. Also adjusted the leveling to allow door to close properly. Unit is now functioning properly. Job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHB08
Near Paige, TX 78659
Matthew
Job Details:
09/14/2022
Arrived onsite to follow tech line recommendations. Checked amp draw and was .5 amps. Checked pressure and was slightly off. Still limited frost pattern. Evacuated system. Ran nitrogen to purge system. Pulled vacuum and held. Recharged per spec. Tested unit for additional 5 minutes and frost was now accumulating throughout evaporator. Recommended customer monitor temperature with bottle of water in freezer. Called customer back later in the evening and no answer. Will need to call customer next day to verify cooling. Job complete
We serviced a
IKEA REFRIGERATOR
Model IX6HHEXDSM01
Near Round Rock, TX 78664
Wesley
Job Details:
09/14/2022
Arrived onsite and found unit had been left running since prior visit and absolute no cool. Replaced compressor and dye drier. Exposed evap and inspected joints under heat shrink for dye leaks. No dye leaks detected. Vacuumed for 20 minutes. Charged system and tested pressures holding at 0 and 130 psi. Unit is now operating as designed. Advised customer on repair.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAHN0
Near Leander, TX 78641
Kimo
Job Details:
09/14/2022
Arrived onsite for dishwasher that is not washing dishes. Upon inspection I found that the was a motor not running code. And through the diagnostics cycle I found that the motor would not run. I replaced the Sump&motor and tested unit and found unit operating as designed no leaks.
We serviced a
KITCHENAID REFRIGERATOR
Model KBFC42FTS03
Near Spicewood, TX 78669
Justin
Job Details:
09/14/2022
"Arrived on site for a refrigerator with lights out after the last service and with it still leaking water. Upon further inspection I found a connector was left unplugged at the control after the last service. I plugged it in and the lights began working. I also found the water coming from the FC. The units drain line was frozen over and the defrost was causing water to come out of the front. I advised the customer on letting the unit thaw for 72 hours and see if it fixes the issue. However, if it does not then the drain line may be clogged. Due to the unit being a built in the drain line was not readily accessible. No fee collected due to being related to the prior service. Call complete."
We serviced a
WHIRLPOOL FREEZER
Model WRS588FIHZ04
Near Seguin, TX 78155
Andrey
Job Details:
09/14/2022
"Arrived on site to test unit for popping noise, tested unit found gasket sealing good sealed some excessive gaps around RC and FC, leveled doors per customer request, reposition wiring harness due to it rubbing against bottom refrigerator panel causing a crackling sound, unit is functioning properly, no leaks detected job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Seguin, TX 78155
Andrey
Job Details:
09/14/2022
"Arrived on site to test unit for not advancing in cycle,tested unit for cold water is not flowing, valve is activating, removed water line and found no water flow, showed customer the issue customer will contact plumber to address issue, all other components checked out in diagnostics, job complete"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF707ESS01
Near San Marcos, TX 78666
Andrey
Job Details:
09/14/2022
"Arrived on site to replace previously diagnosed deli UI assembly, replaced part, advised customer not to set temps in deli drawer lower then 36 to prevent condensation buildup around drawer due to temp difference in RC and drawer, unit is running as designed job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM06
Near Austin, TX 78738
Luis
Job Details:
09/14/2022
"Arrived on site for a defective damaged door,replaced defective freezer door checked door seal and operation good."
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD602ESS01
Near Austin, TX 78749
Luis
Job Details:
09/14/2022
"Arrived on site for light issue. Diagnosed 2 defective led modules,replaced upper left wall freezer led module and lower left wall fresh food led,all leds working as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Austin, TX 78701
Luis
Job Details:
09/14/2022
Arrived on site. Found damaged left side fresh food door replaced defective fresh food door checked door seal good.
We serviced a
WHIRLPOOL DRYER
Model MED7230HW2
Near Jarrell, TX 76537
David Z
Job Details:
09/14/2022
Arrived on site to follow up on dryer making noise when running. Customer showed me video that sounded like rubbing metal and not vibration. I removed the lint screen housing and found the blower wheel was cracked. Removed blower wheel and replaced. Tested unit and found all items working properly. Call complete.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Austin, TX 78735
Scott
Job Details:
09/14/2022
"Arrived on site ,replaced heater . Ran diagnostics per whirlpool specs. All tested normal. No water leaks detected at time of service"