We serviced a
AMANA DISHWASHER
Model ADB1400AGS3
Near Elgin, TX 78621
Scott
Job Details: 10/04/2022
"Arrived on site for dishwasher not filling . Ran diagnostics got 6-4 , 8-2 . Found metal shavings all over outside of drain motor , not getting any voltage to motor . Replaced control and drain pump. Ran diagnostics and unit is performing normally . No water leaks detected at time of service. Job complete ."
We serviced a
WHIRLPOOL COOKTOP
Model WCE55US0HS01
Near Elgin, TX 78621
Scott
Job Details: 10/04/2022
"Arrived on site , replaced left front switch . Tested and all burners are functioning properly . No other issues found . Job complete"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHB4
Near Elgin, TX 78621
Scott
Job Details: 10/04/2022
"Arrived on site for dishwasher not heating . Found element burned thru. Replaced element . Ran diagnostics, heater is getting hot at end of cycle . No water leaks detected at time of service. Job complete"
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Manor, TX 78653
Scott
Job Details: 10/04/2022
"Arrived on site for washer leaking . Ran diagnostics and found valve leaking out bottom . Replaced valve , reran diagnostics. No water leaks detected at time of service. Job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT519SZDM09
Near Manor, TX 78653
Scott
Job Details: 10/04/2022
Arrived on site for fridge not making ice . Ran harvest test and valve never activated. Getting voltage . Replaced valve . Reran harvest all checked normal. No water leaks detected at time of service. Job complete
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32519HZ07
Near Pflugerville, TX 78660
Scott
Job Details: 10/04/2022
Arrived on site for surface light not working . Removed bulb and found filement broken . Customer will supply own bulb. No other issues job complete
We serviced a
WHIRLPOOL VENTHOOD
Model WVU17UC0JS0
Near Austin, TX 78724
Leonardo
Job Details: 10/04/2022
Arrived on site to test unit for unit venting from the top. Test unit and found cover loose leaking air. Secured cover test unit and unit test good job complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Taylor, TX 76574
Cliff
Job Details: 10/04/2022
Arrived on site to diagnose a refrigerator that is not dispensing ice. Found ice cubes stuck in crusher area and preventing motor function. Removed ice and tested unit. Found all is functioning properly at this time and no leaks were found at time of service.
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Copperas Cove, TX 76522
David Z
Job Details: 10/04/2022
"Arrived on site to follow up on washer that is tripping breaker when spinning. Found no error codes present. Unit passes diagnostics. Found voltage and polarity good. Previous tech already replaced motor / cap / control. Called tech line and spoke with Travis, R7734741694. Unit is still running through a GFCI outlet, with a GFCI cutoff in the room, and breaker panel. Unit is operating as designed, breaker is not able to support the unit due to weak GFCI. Advised to contact electrician to try a stronger breaker / GFCI since unit is operating in spec, and is not recommended to be installed on GFCI breakers. Call complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LWO
Near Pflugerville, TX 78660
Wesley
Job Details: 10/04/2022
Arrived onsite and found unit tripping breaker half the time. Determined that the likely cause was a non compatible GFCI breaker being used on the dedicated washer circuit. Customer will test with separate circuit to determine cause. All else checks good.
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Georgetown, TX 78626
Lou
Job Details: 10/04/2022
"Arrived on site to inspect washer basket paint chipped and rusting. Upon further inspection, I found a dime sized paint chip in the bottom of the basket and it was beginning to rust. I removed and replaced the basket and tested the unit in diagnostics. Unit is operating as designed. No water leaks observed during service, job completed."
We serviced a
MAYTAG DRYER
Model MED6230HC2
Near Austin, TX 78738
Kevin
Job Details: 10/04/2022
"Arrived on site and inspected dryer and found loose wire connection at door switch. After resetting connector dryer is now running properly, job complete"
We serviced a
WHIRLPOOL DRYER
Model MEDC465HW0
Near Briarcliff, TX 78669
Kevin
Job Details: 10/04/2022
"Arrived on site and inspected dryer and found it is not heating. Found cut off has failed. After replacing cut off dryer is heating normally. Found airflow meter is showing restricted and recommended that vent to the exterior be serviced, job complete"
We serviced a
MAYTAG WASHER
Model MHW8200FW0
Near Dripping Springs, TX 78620
Kevin
Job Details: 10/04/2022
"Arrived on site and replaced UI, washer is now responsive and will complete a diagnostic cycle, job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM0A
Near Canyon Lake, TX 78130
Andrew
Job Details: 10/04/2022
"Arrived on site to test unit for water leaking from dispenser tube onto front panel of FC door. Adjusted water line, unit working as designed. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near New Braunfels, TX 78130
Andrew
Job Details: 10/04/2022
"Arrived on site to test unit for not starting. Found tub full of water. Found blue wire to drain pump was cut. Installed spade connection, unit working as designed. No leaks detected. Job complete."
We serviced a
KITCHENAID COOKTOP
Model KFGC506JSS01
Near Dripping Springs, TX 78620
Kevin
Job Details: 10/04/2022
"Arrived on site and inspected range and found front middle and right rear burner were not converted to propane. I have to correct and them customer also pointed out that oven is not working. Removed lower rear panel and Found igniter wire is not connected to igniter. After reconnecting wire oven is now working properly, job complete"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Cedar Park, TX 78613
Kimo
Job Details: 10/04/2022
"Arrived onsite for a dryer that is tumbling but is not heating. Upon arrival I tested unit and found that it would not heat. I tested the heating element, all thermistors and fuses and found the all good. I checked the vents and found that the airflow was good see pix. Upon further inspection I found that the unit was wired incorrectly and correcting this I tested the unit ad found the unit operating as designed. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Taylor, TX 76574
Cliff
Job Details: 10/04/2022
Arrived on site to replace previously ordered parts for washer. Replaced control and tested unit. Found all is functioning properly at this time and no leaks were found at time of service.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Killeen, TX 76549
David Z
Job Details: 10/04/2022
Arrived on site to diagnose refrigerator leaking from the rear. Found water dispenser hose had a Crack in it. Cut out damaged section and used a coupler from truck stock to connect the lines. Unit no longer leaking. Call complete.
We serviced a
KITCHENAID REFRIGERATOR
Model KFIS29BBMS02
Near Temple, TX 76502
Tyler
Job Details: 10/04/2022
"Arrived on site for unit not cooling and making a loud noise. Upon arrival was able to confirm issue and found following results for thermistors: Fc thermistor 10.7k, rc thermistor 6.1k, ice bin thermistor 7.3k, rc evap thermistor 8.2k. found no failures in the RC compartment but I did find a partial defrost issue in the freezer indicating unit was going to defrost too early and shutting down too quickly causing ice to build around the fan due to a failing by metal thermostat. Was able to replace evaporator fan motor in FC as well as high-voltage control and inform customer to give unit 24 hours to stabilize tips. Call complete"
We serviced a
MAYTAG DRYER
Model MED7230HW2
Near Belton, TX 76513
Tyler
Job Details: 10/04/2022
Dont type and drive I turned it on. Upon arrival was able to confirm issue and upon further testing found that unit would not power on due to a voltage issue in the outlet. Found left side of outlet giving 121 V that sound right side of outlet only giving 8 V and when combined between the left and right side of the L1 and L2 to unit overall was only receiving 108 V. Instructed customer they would need electrician to fix the power supply issue and unit would function as designed. Call complete
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS00
Near Austin, TX 78733
Luis
Job Details: 10/04/2022
"Arrived on site for a defective compressor and pump. Replaced pump,compressor,drier and evaporator,vacuumed system down unit kept vacuum recharged system to manufacture spec,reassembled unit checked available connections and tubing no leaks. Ran diagnostics all test passed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC704FPS05
Near Austin, TX 78757
Luis
Job Details: 10/04/2022
"Arrived on site for water leaking from dispenser compartment. Customer played video,water leaking from behind paddles,checked ice door operation good and sealing,tested water dispenser no leaks. Ran icemaker test,icemaker passed harvest,ran fill test passed no leaks,ran ice box fan good strong air flow. Unable to recreate issue."
We serviced a
MAYTAG DRYER
Model MED7230HW2
Near Round Rock, TX 78681
Gerry C
Job Details: 10/04/2022
"Arrived to inspect drying time issue. The CX said the unit had increased time on one load, but it was a single occurrence and operated normally on subsequent attempts. I found no issues with the unit and advised the CX that the timer can change values dependent upon moisture content within the garments. The unit would register a vent error message and I found excessive debris at the vent out let and removed it. Subsequent testing showed the error resolved. Operational test good, steam dryer, no leaks observed during service."
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Round Rock, TX 78681
Gerry C
Job Details: 10/04/2022
"BT arrived on site to inspect washer. The unit was making a squealing noise when spinning. I removed and replaced the gear case, shifter and belt. I ran the unit through diagnostics and the unit operates as designed. No water leaks observed during service."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS08
Near Jarrell, TX 76537
Paul
Job Details: 10/04/2022
Arrived Onsite to inspect microwave making noises. Upon arrival CX reports that the sound is a tapping like a fan tapping against something and the CX said that the noise stopped Sunday and has not returned since. I tested the output wattage and got 1000 watts. I tested the unit and was unable to reproduce the tapping the CX is reporting. I instructed the CX that the tapping may have been from a shaving falling into the microwave fan and must have blown out. Call complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Round Rock, TX 78665
Maurice R
Job Details: 10/04/2022
"Arrived onsite for refrigerator not cooling. On inspection found the evap was covered in ice.Tested the bi metal and it was working, retested the thermistor and they were in range. Called Tech line and went through few test with them. Let the tech that I had. Gap on the bottom of the T molding. The tech had me send him pics of the gap and it is under apex review. They will reach out to me in a few days to let us know what to do next. No water leaks detected during service. Sr 7734742713"
We serviced a
WHIRLPOOL DRYER
Model WED5100HC0
Near Waco, TX 76705
Jonathan M
Job Details: 10/04/2022
Arrived on site for a dryer that is not advising the customer when cycles are completed and is intermittently flashing an F2 E1 (stuck key). Add confirm the customers complaint and found the screen sitting on an F2 E1 error message before touching the unit. The customer advised that this will happen when she is not pressing any buttons. Checked power to the unit and found proper voltage and polarity. Checked voltage to the user interface and found proper voltage. Opens it replaced the user interface and tested the unit. The unit began to work and operate as designed. Call complete.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM6
Near Round Rock, TX 78665
Maurice R
Job Details: 10/04/2022
Arrived onsite for dishwasher not drying properly. On inspection the unit was working as designed. Informed CX on how the new dishwasher performed. CX complaint was that water stays inside the dishwasher. CX is not using rinse aid so informed on how rinse aid helps with drying of the dishes. Let CX know that plastic dish will hold water and that the plastic tub holds the water after it is done. Told CX to open the door once the cycle is done to help dry the dish. No water leaks detected during service.
We serviced a
WHIRLPOOL DRYER
Model MED8630HW2
Near Round Rock, TX 78665
Maurice R
Job Details: 10/04/2022
"Arrived onsite for dryer making noise. On inspection found that the drum was hitting the side of the dryer when spinning and there was moisture in the display. Reset the drum so it does not hit the side of dryer and switched out the UI, the UI had a piece of plastic that folded over the control board. The old UI did not have the plastic folded over the control board. Unit is working as designed. Took pics of where the dryer was hitting the side."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW2
Near Georgetown, TX 78626
Maurice R
Job Details: 10/04/2022
"Arrived onsite for previously diagnosed parts. Gain access to unit installed wash plate, agitator and resisted the hub. Tested unit in diagnostics mode and working as designed. Testing in the rinse and spin mode. No water leaks detected during service."
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Austin, TX 78723
Joe Z
Job Details: 10/04/2022
Arrived onsite for Dryer on but not turning. Making a loud noise. Motor sounds like it is seized.. upon arrival test unit and motor would hum and release smoke. Need to replace motor. Replaced motor and test unit. Unit is operas designed. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ01
Near Austin, TX 78723
Joe Z
Job Details: 10/04/2022
Arrived onsite for Fridge dmg bottom right door. Arrived on site to replace bottom right door. Replaced door. Job complete
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US0HS00
Near Pflugerville, TX 78660
Wesley
Job Details: 10/04/2022
Arrived onsite and found unit operating with difficult long ignition times on the front left and front right burner. Found both caps out of place following a cleaning. Secured caps in place and cleared debris out of orifices and tested unit. All checks good. Advised customer on repair.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Austin, TX 78730
David S
Job Details: 10/04/2022
"Arrived on site for dishwasher not drying. I inspected the unit and work area. I found no fault codes in diagnostic. Ibran a diagnostic cycle and found all components turning on. Including the heating element. I advised the leasing office to have the tenant run hot water at the sink till it get hot then start the dishwasher, and I advised on the use of rinse aid to help woth the drying. Job complete."
We serviced a
WHIRLPOOL MICROWAVE
Model KMHS120ESS11
Near Austin, TX 78704
David S
Job Details: 10/04/2022
"Arrived on site for microwave tripping the breaker. I inspected the unit and work area. I plugged the microwave into an outlet in the living room and found it working as designed. I found the outlet for the microwave not on its own dedicated breaker, I found it sharing a break with the kitchen outlets including a GFCI outlet. I plugged my outlet tester into all the outlets wired together and found the GFCI tripping every time I reset it. I plugged my outlet tester into an outlet in the living room and found it working. The microwave should be on its own breaker, and should not be wired into a GFCI outlet. The micr is working as designed. Job complete."
We serviced a
MAYTAG DRYER
Model MED7230HC2
Near Austin, TX 78731
David S
Job Details: 10/04/2022
Arrived on site to replace the dryer lid. I replaced the lid. The unit is in working order. Job complete.
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JS0
Near Jarrell, TX 76537
Paul
Job Details: 10/04/2022
Arrived onsite to inspect oven with a dent in the drawer. I found the dent in the drawer a took a picture of it. R/R drawer panel. Operational test good. Call complete.
We serviced a
WHIRLPOOL RANGE
Model WFE535S0LZ2
Near Waco, TX 76705
Jonathan M
Job Details: 10/04/2022
Arrived on site for a range that has a contract handle. Inspected unit and work area. Did confirm the handle had been cracked behind the actual handle. Replaced the handle assembly and tested the unit. The unit began to work and operate as designed. Call complete.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHW4
Near Waco, TX 76705
Jonathan M
Job Details: 10/04/2022
Arrived on site for a dishwasher that has a broken dispenser. Inspected unit and work area. Confirmed the customers complaint and replaced the dispenser. Tested the unit in the unit is now working as designed. Call complete.
We serviced a
WHIRLPOOL WASHER
Model WTW5100HC0
Near Waco, TX 76710
Jonathan M
Job Details: 10/04/2022
"Arrived on site to install previously diagnosed parts. Inspected unit and worked area. Replaced the basket, tub, gear case, drain pump filter, cam, capacitor, actuator, spanner nut, wash plate, and screws. Tested the unit and the unit began to work and operate as designed. Call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model MSS25C4MGZ06
Near Gatesville, TX 76528
Tyler
Job Details: 10/04/2022
Arrived on site for refrigerator needing previously diagnseale system. Upon arrival reconfirmed issue and installed required parts. Used nitrogen and found no leaks and then pulled vac and recharged system with 68grams of r600. Found unit temps dropping after 10 minutes of run time and found coil frosting over. Informed customer to give unit 24 hrs to stabilize temps. Call complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT138FFDW00
Near Leander, TX 78641
Kimo
Job Details: 10/04/2022
Arrived onsite for refrigerator with door gaskets that are falling off. Upon inspection I found that that door gasket had cam loose from the doors. I the reattached the gaskets after checking for another major damage and dining none. I used my heat gun to remove any deformities in the gaskets and made sure that they sealed up properly. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRMF706ESS05
Near Salado, TX 76571
David Z
Job Details: 10/04/2022
"Arrived on site to diagnose refrigerator thst will not reset the filter indicator. Tried process per use and care guide with no change. Called tech like and spoke with Ed, SR7734738451. Checked via test 67 and confirmed filter switch is working as intended. Power cycled unit per tech Line request. After power cycling found the display is properly reset. Advised if any further issues happen with the reset, we need to replace the UI. Call complete."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Temple, TX 76502
David Z
Job Details: 10/04/2022
Arrived on site to diagnose washer throwing F2E2 error. Found service pointer W11436350 applies. Removed console and found one ribbon cable disconnected from its connector. Tried to reseat and could not get console to power on again. Was going to replace console but found new one also had a disconnected ribbon cable and the fascia trim was broken. Attempted to reseat ribbon cable in original console and was able to get it to power on. Once I did it threw an F6E1 error for not able read control. Replaced control. Retested and verified all functions correct and its now starting cycles. Call complete.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Leander, TX 78641
Kimo
Job Details: 10/04/2022
Arrived onsite to install previously designed parts upon arrival I installed new oven bottom and found that it fit normally. Job complete.
We serviced a
MAYTAG WASHER
Model MVW7230HC0
Near Belton, TX 76513
David Z
Job Details: 10/04/2022
"Arrived on site to diagnose washer making loud noise when spinning. Customer showed me video of loud noise coming from spin, high pitched in nature. Even hand turning the agitator and basket you could feel bearings rubbing. Replaced gearcase and tested. Verified noise is at normal operating levels. Call complete."
We serviced a
KITCHENAID MICROWAVE
Model KOCE500ESS20
Near Georgetown, TX 78633
Paul
Job Details: 10/04/2022
"Arrived onsite to install previously diagnosed and ordered parts. R/R interlock harness, magnetron, and the inverter. I tested the unit and the unit is now operating as designed. Call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ02
Near Georgetown, TX 78633
Paul
Job Details: 10/04/2022
"Arrived onsite to install previously diagnosed and ordered parts. R/R ice bin door and tested. Ice bin door is no longer gaping at the bottom or on the sides. Operational test good,no leaks observed during service."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Driftwood, TX 78619
Kevin
Job Details: 10/04/2022
"Arrived on site and replaced heating element per service pointer, job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Austin, TX 78729
Vincent
Job Details: 10/04/2022
"Arrived on site for refrigerator, inspected unit and work area. Used the silicone to seal the cavity with frame on RC & FC. No more leaks where observed during service. Advised CX to remove all ice build up in the freezer or to fully defrost. Water leaks where observed during service. Job completed."
We serviced a
WHIRLPOOL MICROWAVE
Model WML55011HS07
Near Dripping Springs, TX 78620
Kevin
Job Details: 10/04/2022
"Arrived on site and replaced interlock kit diagnosed on previous visit. After replacement microwave is working properly, job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ00
Near Round Rock, TX 78681
Gerry C
Job Details: 10/04/2022
"Arrived to inspect no cool. I found the unit with no cooling ability and the compressor was running. The CX advised me it had operated about 15 days after the last repair. I checked pressures and found at rest, 1 psi within the system. I pressurized the entire system to 140 psi and found no leaks on any accessible joints in the lower unit area, or the evaporator area as well. I isolated the high side to include the compressor, condenser and Yoder and found a pressure drop of 3 psi in 15 min. But only observable when pressurized to above 200 psi and the drop notated occurred at 250 psi. I then isolated the Yoder and retested and found the same results, when the compressor and condenser were included. I contacted the MFG tech line, Chris. Advised of my findings and was given SR# 7734736511. The unit has been submitted for replacement due to a leak within the cabinet that is not repairable. The CX will be contacted by the MFG to arrange replacement. No leaks observed during service."
We serviced a
GE REFRIGERATOR
Model GNE27JYMNFFS
Near Round Rock, TX 78681
Gerry C
Job Details: 10/04/2022
BT arrived on site to inspect refrigerator. Packaging tape was on one of the rails for the freezer door I removed the tape and set the feet down to level the unit. Now the freezer door opens easily and the whole unit wont roll out. Office to charge service call only. No leaks observed during service.
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS
Near Austin, TX 78726
Vincent
Job Details: 10/04/2022
"Arrived on site for range, inspected unit and work area. CX complaint is that front right burner does not turn on. Removed glass top and found element broken. Replaced element and tested unit. Unit is operating as designed. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Austin, TX 78758
Vincent
Job Details: 10/04/2022
"Arrived on site for washer, inspected unit and work area. Entered diagnostics and tested unit. No error codes were found. Water pressure from home is good. Explained to CX that unit is operating as designed. No water leaks present at time of service. Job complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHV04
Near Austin, TX 78727
Vincent
Job Details: 10/04/2022
"Arrived on site for refrigerator, inspected unit and work area. Retrieved FC Temp 2?. CX complaint is that FC ice maker does not produce ice. Inspected IM and found motor seizing. Replaced IM and tested unit. Unit is operating as designed. Leveled feet on refrigerator. No water leaks present during service. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Austin, TX 78728
Vincent
Job Details: 10/04/2022
"Arrived on site for washer, inspected unit and work area. Replaced all parts ordered by previous tech. Gained access to gear case suspension and replaced with the new parts. When removed the old gear case there was premature of failing seals caused by to much detergent, CX is equipped with water softener and explained he needs to use way less detergent. Tested unit and its now operating as designed. No leaks where observed during service. Advised CX if he continues to have any more problems to call Whirlpool CX service."
We serviced a
MAYTAG WASHER
Model MVW7232HC0
Near Austin, TX 78741
Joe Z
Job Details: 10/04/2022
Arrived onsite for noise coming from washer . Upon arrival ran diagnostics and there were no error codes. Test unit and during draining the pump would make a clicking sound. Removed pump for inspection and found debris stopping impeller and causing a clicking sound. Need to replace pump. Replaced pump and test unit . Unit operas designed. No leaks present at this time. Job complete
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Del Valle, TX 78617
Joe Z
Job Details: 10/04/2022
"Arrived onsite to install previously ordered parts. Installed suspension,control , and latch. Test unit and unit operates as designed. No leaks present at this time. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW6120HC2
Near Buda, TX 78610
Joe Z
Job Details: 10/04/2022
Arrived onsite for Knocking or Thumping Noise. Upon arrival ran diagnostics and there were no error codes. Ran auto cycle and all components operate correctly. There is no shaking during spin. Ran a normal cycle with clothes . Found that during the start of spin cycle the drain hose was tapping the back panel. Secured the hose so that it is away from panel. No leaks present at this time. Job complete.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM03
Near Hutto, TX 78634
Cliff
Job Details: 10/04/2022
Arrived on site to diagnose a refrigerator that is not producing ice. Found icemaker turned off and reset bail arm to on position. Tested unit and found all is functioning properly at this time. Advised customer on findings and no further repairs needed. No leaks were found at time of service.
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Hutto, TX 78634
Cliff
Job Details: 10/04/2022
Arrived on site to diagnose an oven that is not heating. Found bake ignitor faulty and replaced it. Tested unit and found all is functioning properly at this time.
We serviced a
WHIRLPOOL FREEZER
Model WRF767SDHZ03
Near Buda, TX 78610
Joe Z
Job Details: 10/04/2022
"Arrived onsite to install previously ordered parts. Installed regulator,waterline,fill tube, and 3 way water valve . Test unit and unit is operating as designed. No leaks present at this time. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WFW92HEFCO
Near Round Rock, TX 78681
Gerry C
Job Details: 10/03/2022
BT arrived on site to inspect washer. The unit was draining at a slow rate. I removed the service port next to the drain pump and found debris clogging the drain hose. I removed debris and tested the unit. The unit now operates as designed. No leaks observed during service
We serviced a
JENN-AIR RANGE
Model JGRP436HL01
Near Liberty Hill, TX 78642
Vincent
Job Details: 10/03/2022
"Arrived on site for range, inspected unit and work area. I had arrived on site to install previously diagnosed parts while I was accessing to replace the door latch I tested it and showed to be good, so I proceeded to re/diagnosing and installed only the UI. Called techline and spoke to Drew sr#7734731485 and proceeded with testing and found the control good. After installing the Ui also found that the igniter for bake was reconnected and tested. Unit is now operating as designed. No leaks where observed during service. Job completed."
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GPS0
Near Cedar Park, TX 78613
Paul
Job Details: 10/03/2022
"JM: Arrived onsite to inspect dishwasher leaking water under the unit. I found error code F9E1. I found that the leak is coming from the diverter. The sump and motor assembly need to be replaced. R/R sump and motor assembly and tested. Operational test good, no leaks observed during service.
We serviced a
GE DISHWASHER
Model GLD5600N00BB
Near Georgetown, TX 78633
David Z
Job Details: 10/03/2022
"Arrived on site to diagnose dishwasher that was making a loud grinding noise. Traced grinding to drain pump. Replaced drain pump, tested, and confirmed no water leaks present. Call complete.
We serviced a
WHIRLPOOL WASHER
Model WTW7000DW0
Near The Hills, TX 78738
Scott
Job Details: 10/03/2022
"Arrived on site for washer leaking . Found valve leaking right away in diagnostics. Replaced valve . Reran diagnostics all checked normal. No water leaks detected at time of service. Job complete"
We serviced a
WHIRLPOOL MICROWAVE
Model KMBS104ESS02
Near Austin, TX 78739
Leonardo
Job Details: 10/03/2022
Arrived on site to test unit for touch panel not working sometimes on right side but when customer resets unit the buttons work. Will need new panel W11197501 and control board W10891907.
We serviced a
KITCHENAID RANGE
Model KDRS483VSS03
Near Austin, TX 78746
Leonardo
Job Details: 10/03/2022
Arrived on site to replace right front valve with switch. Resolved valve no leaks present burner igniting correctly job complete.
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPS00
Near West Lake Hills, TX 78746
David S
Job Details: 10/03/2022
"Arrived on site to clean the ice machine. I found the clean light on. I pulled the unit out of the cabinet and found the boards underneath uneven. I leveled the boards, and reinstalled the unit. I removed all the ice and used the cleaning solution to wipe down the interior of the ice machine. I started a clean cycle. I opened the kick plate and clean the condenser. I advised the customer after the unit is done running a clean cycle to let it run in normal operation for a couple of hours and then to dump out the ice, everything after that will be usable. job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW1
Near Bastrop, TX 78602
Joe Z
Job Details: 10/03/2022
Arrived onsite for continued issues with uni leaking. Found water leaking at front top of tub under tub ring. Removed and reinstalled tub ring securely. No leaks present at this time. Job complete
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF505ESS01
Near Austin, TX 78747
Scott
Job Details: 10/03/2022
Arrived on site for no cool fresh food . Found small amount of frost on evap . Steamed out cover . Customer had had another company out and they didnt plug fan back in . Ran diagnostics all checked normal. Set fridge to 8hr defrost and set temps back to recommend settings . No water leaks detected at time of service.
We serviced a
WHIRLPOOL ICE MACHINE
Model GI15NDXZS2
Near Belton, TX 76513
Tyler
Job Details: 10/03/2022
Arrived on site for ice machine no5 filling correctly and making loud noise. Upon arrival confirmed issue. Upon further testing I found cause of failure was the inlet valve failing to allow enough water into unit and leading to recirc. Pump to hum loudly.I installed required valve and tested unit. Found no leaks and unit could function as designed. Calll complete
We serviced a
GE WASHER
Model GFW450SSM1WW
Near Temple, TX 76502
Tyler
Job Details: 10/03/2022
Arrived on site for washer needing replacement of drain motor. Upon arrival customer provided part needed for repairs. Installed part then reassembled and tested u it. Found no leaks and unit cycled through normal selections mode as designed.
We serviced a
WHIRLPOOL WASHER
Model WFW92HEFCO
Near Round Rock, TX 78681
Gerry C
Job Details: 10/03/2022
BT arrived on site to inspect washer. I ran the unit through diagnostics and error code F9E1 showed. I removed the service port next to the drain pump and found it clogged with debris. I cleaned the port out and tested. The unit now operates as designed. No leaks detected during service.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Leander, TX 78645
Lou
Job Details: 10/03/2022
"Arrived on site to inspect refrigerator freezer light not working. Upon further inspection, I found the freezer light and the lights in the ice box and waterbox not working. Per service pointer #W11460554, I removed and replaced the module and tested and all lights came on.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ
Near Kyle, TX 78640
Kevin
Job Details: 10/03/2022
"Arrived on site and found refrigerator has been replaced,
We serviced a
WHIRLPOOL OVEN
Model WGG745S0FS00
Near Pflugerville, TX 78660
Cliff
Job Details: 10/03/2022
Arrived on site to diagnose an oven that is not heating. Found bake ignitor faulty and replaced it. Tested unit and found all is functioning properly at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDBM00
Near Round Rock, TX 78664
Cliff
Job Details: 10/03/2022
Arrived on site to replace previously ordered parts for refrigerator. Replaced door gasket and shaped it using applied heat. All is working properly at this time and no leaks were found at time of service.
We serviced a
WHIRLPOOL WASHER
Model CET9000GQ2
Near Blanco, TX 78606
Andrew
Job Details: 10/03/2022
6543-Arrived on site to test unit for not draining. Found error f27(excessive water in tub). Ran diagnostics 3x and two loads with no issues however did find extreme amount of suds. Advised customer soap needs to be cleaned out to prevent water level switch from reading suds and thinking it is water. No leaks detected.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ01
Near Austin, TX 78725
Matthew
Job Details: 10/03/2022
Arrived onsite to replace dispenser door and dispenser tube. Replaced parts and tested. Unit is functioning properly. No leaks present at this time. Job complete.
We serviced a
WHIRLPOOL WASHER
Model LSE7806ACE
Near Austin, TX 78703
Wesley
Job Details: 10/03/2022
"Arrived onsite and installed new roller due a roller seizing and causing some noise, also found loose blower. Secured blower with bolts and braced housing with copper wedge. Charged unit is now quieter to operate.
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Austin, TX 78745
Wesley
Job Details: 10/03/2022
Arrived onsite and found unit operating with significant backflow causing the sensor functions to end cycles prior to completed drying function. Advised customer on findings and recommended using the time dry function under the circumstances. All else checks good.
We serviced a
WHIRLPOOL WASHER
Model WFW87HEDW0
Near Lakeway, TX 78738
Justin
Job Details: 10/03/2022
"Arrived on site for a washing machine that was not draining nor spinning. On arrival the customer stated he was washing heavy mats on extra fast and the unit would not spin and they came out soaking wet. He stopped the cycle and put it on a drain & spin on the fast setting, but the same thing occurred. I put the unit into diagnostics mode and found stored error codes F5E4 for door not opened between cycles, F5E3 for for door unlock error, F5E2 for door lock error, and F8E3 for overflow condition. I cleared the error codes. I then ran a diagnostics cycle and a drain & spin cycle to find the unit running as designed. I informed the customer he may have overloaded the unit and I found the unit running as designed at the time of service.
We serviced a
WHIRLPOOL WASHER
Model MVW7232HW0
Near Kyle, TX 78640
Justin
Job Details: 10/03/2022
"Arrived on site for a washing machine showing a maintenance error on the UI. On arrival the customer stated it appeared to be some sort of error code on the screen and they were unsure what it was. They also found the unit walking forward and shaking excessively. I put the unit into diagnostics mode and found no stored error codes. I then ran a diagnostics cycle and found it ran through as designed. I then gained access to the bottom of the unit and found significant gearcase oil indicating a failing gearcase, which is most likely causing the excessive shaking. I checked the suspension and found it fine. I found the unit had a 5 year Home Depot warranty and advised the customer to reach out to them for the repair.
We serviced a
GE RANGE
Model JGBS30REK2SS
Near Georgetown, TX 78628
David Z
Job Details: 10/03/2022
"Arrived on site to diagnose range that is not lighting the oven. Tested unit and found voltage coming from thermostat going to igniter. Chrcked igniter and found resusgence good, indicating failure in the safety valve coil. Got approval from Jeanette for repair. Replaced safety valve and tested. Verified unit working as designed. Call complete."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH75021HZ1
Near Round Rock, TX 78665
Gerry C
Job Details: 10/03/2022
BT arrived on site to inspect microwave not heating. Upon inspection I found the magnetron to be not working
We serviced a
KENMORE DRYER
Model 110.61082
Near Georgetown, TX 78628
David Z
Job Details: 10/03/2022
"Arrived on site to diagnose dryer that will only run on one setting. Attempted to change settings and panel just beeps and resets to the same setting, likely indicating a failed button in the console membrane or ribbon cable.
We serviced a
LG WASHER
Model WT7305CW
Near Holland, TX 76534
Tyler
Job Details: 10/03/2022
"Arrived on site for washer not turning on. Upon arrival confirmed issue. After further testing found unit receiving proper voltage but had not control response. Found no shorts in drain motor, or other hardware. call complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ01
Near Georgetown, TX 78628
Gerry C
Job Details: 10/03/2022
"Arrived to inspect no cool. I found the unit powered up, but there was no compressor. The UI would respond to single button presses, but not to two keys at the same time and would not go into service mode or change cooling status. After unplugging for 30 seconds and re-applying power, the unit started up and operated as normal. It had been off in the prior condition for several days and was fully warm. I suspect the control issue due to excessive moisture within the chassis and the MFG tech agreed with the possibility. The compressor only drew .85 amps after five minutes and should have been higher, however, cooling was apparent. The compressor was loud, but there was a much louder vibration from within the cabinet and I found the evaporator fan shaft bent enough to cause the issue, even with the blades removed. I suspect ice in the evaporator as the cause for the bent shaft. Further inspection revealed the lower mullion area was gapped due to mis-manufacture and I contacted MFG tech Andrew. File# 7734721362 and advised of my findings.
We serviced a
MAYTAG FREEZER
Model MZF34X16DW01
Near Leander, TX 78641
Vincent
Job Details: 10/03/2022
"Arrived on site for freezer, inspected unit and work area. CX complaint is that freezer stopped freezing. Retrieved temps at 23?. Inspected unit and found ice buildup on evap. Ohmed heater out at 32ohms. Entered diagnostics to force defrost and found control shorted. Job complete.
We serviced a
MAYTAG WASHER
Model MHW3505FW1
Near Round Rock, TX 78681
Vincent
Job Details: 10/03/2022
"Arrived on site for washer, inspected unit and work area. CX complaint is that unit door locked with their clothes inside. Entered diagnostics and found error codes F9E1, F8E3, & F3E1. Ran unit through cycle and found excessive suds. Opened drain pump and cleaned filter screen of debris. Unit has a strong drain flow. (See attached photos.) Informed CX that we found an excess of suds. No water leaks present at time of service. Unit is operating as designed. Job complete."
We serviced a
WHIRLPOOL RANGE
Model WFE525S0JZ0
Near Georgetown, TX 78626
Maurice R
Job Details: 10/03/2022
Arrived onsite for burner not working correctly. On inspection the left front burner on high would come on then shut off for 45sec to a minute at a time. Replaced the burner and tested the unit again. When on high the new burner would turn off for 10 to 15 seconds then come back on. The unit is working as designed.
We serviced a
WHIRLPOOL MICROWAVE
Model WOC54EC0HS20
Near Georgetown, TX 78626
Maurice R
Job Details: 10/03/2022
Arrived onsite for previously diagnosed parts. On inspection installed parts that were ordered to fix install issues. The unit is working as designed.
We serviced a
WHIRLPOOL RANGE
Model WFG320M0BS3
Near Georgetown, TX 78626
Maurice R
Job Details: 10/03/2022
Arrived onsite for range oven door broken. Arrived onsite to replace the glass in door. Replaced the glass and unit is operating as designed. No gas leaks detected during service.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Liberty Hill, TX 78642
Vincent
Job Details: 10/03/2022
"Arrived on site for washer, inspected unit and work area. CX complaint is that unit leaks while using fabric softener on heavy loads. Inspected unit and found sock blocking fabric softener dispenser inlet on tub ring. Explained to CX what we found and that the tub and all hoses were good. Called WP techline and spoke to Chris 7734729651. Techline instructed to change tub ring if no issues were found. Advised CX to level unit once its installed back into their home. No water leaks present during service. Job complete."
We serviced a
WHIRLPOOL COOKTOP
Model WCG55US6HS00
Near Leander, TX 78641
Kimo
Job Details: 10/03/2022
Arrived onsite for a rang with Burners that clicking. Upon arrival I tested unit several time and couldnt find anything thing out of the ordinary I contacted safety and told Kent of my findings and got sr# 7734692660.. job complete