"Arrived on site for a wall oven that has an oven door that is rattling. Inspected unit and work area. Did confirm the customers complaint and disassembled the upper door. Found all screws in place and the issue with the metal glass rattling against the clips. Attempted to adjust all clips holding the glass and was unable to remove the light rattling sound occurring. I called Whirlpool Techline and spoke to Chris SR# 7734985265. He advised that this issue may just be due to having to be serviced out in the field but to go ahead and order the outer door, metal glass, and clips for repair. Ordering parts in the office will need to contact the customer about a return date due to several out of stock and PSP items.; ordrng 1 W11602609 (Outer glass) and 2 W11598131 (Glass clip)s and 1 W11600213 (Middle glass)"

"Arrived onsite for refrigerator not cooling after repair. Upon arrival inspected unit. Found ice block on cap tub right hand corner of evaporator. Checked pressure and recorded 0psi at high side with unit off, should have been equalized. Called tech line for assistance. Tech, Rob, Gas stated unit should be equalized at about 28 psi. Ran unit and high side did not move, low side dropped in pressure. Tech recommended running nitrogen at 140 psi to clear restriction. Running nitrogen Low to high. Then holding vacuum for 20 min. Provided SR#7734986741. Ran nitrogen and found blockage at cap tube to dryer. Cleared line and replace new dryer. Vacuum held and when to charge however refrigerant was leaking from charge tube. Will need to return with corrected charting tube, pull vacuum and recharge. ; ordrng 1 R600kit (R600 kit)"

Arrived on site to diagnose a refrigerator that is leaking. Found water valve seeping causing damage to icemaker fill line. Valve and line will need to be replaced to complete repairs. Return date set .; ordrng 1 W11415785 (Tube) and 1 WPW10312696 (Valve)

Arrived onsite for MW not powering up. On inspection found a sensor was burnt in the back side of the unit. Replaced the wiring harness and tested unit. The unit was heating a 1100 watts and heated a cup water to 212?. The unit was operating as designed.

Arrived onsite for Not Dispensing Crushed Ice . Upon arrival test unit and not dispensing neither cubed or crushed ice. Found Dispenser Impeller is stripped onto the dispenser motor shaft causing auger not to push ice out of bin. Need to order impeller and motor. Office to reschedule ; ordrng 1 WP63052 (Impeller) and 1 W11310391 (Motor) and 1 WPW10309864 (Ice box divider)

Arrived on site to diagnose range with deformed panel. On arrival found the trim on the right side of the outer door glass is peeling off and warped. Ordering new outer glass panel. ordrng 1 W11176456 (Outer Glass) and 1 W11178521 (Nameplate)

"Arrived on site for Maytag commercial washing machine not agitating. I inspected the unit and work area. I gained access to the gear case and tested the capacitor, motor and shift actuator, I found the shift actuator way out of range. I replaced the actuator, because the actuator was out of range I am ordering the control to complete the repair. ordrng 1 W11411581 (Control) and 1 W10528947 (Hub)"

Arrived onsite for previously diagnosed parts. On inspection found the Wrong part was sent with me. Reschedule when we get the right part. No water leaks detected during service ;

"Arrived onsite for a dishwasher displaying an F8E4 error. The customer stated the last couple of times they washed dishes they were not clean. I checked stored error codes and found an F8E4, FAE2, F8E2, & F7E1. I cleared the codes and started the service diagnostics cycle. The drain pump started immediately and the wash pump started a few seconds later. I found the unit drawing 4.5 amps because the wash pump was locked up. I tried a regular cycle and the same thing happened. The unit never tried to fill with water and there was no voltage to the valve. I found the float switch sticking so I replaced it and retested getting the same results. The control, sump and motor, & vent need to be replace then the unit tested. The fill valve could possibly need to be replaced. Ordering W11416362 sump and motor and W11434044 fill valve. Marking other parts as use on return visit. Office to RS.; ordrng 1 W11416362 (Sump and motor) and 1 W11434044 (Fill valve)"

Arrived on site for refrigerator not cooling properly. Upon arrival confirmed issue and found defrost issue in fc. Found thermistor value of evap thermos over 60k (buried in ice. Rc compartments was at 2-3k (around 60-70degrees). Found control was failing to read accurate temps. Will need office to reschedule once availability of parts is known.; ordrng 1 W11546690 (Contrl) and 1 W11546681 (Harness wires) and 2 WPW10384183 (Thermistor)s

"Arrived on site and inspected refrigerator and found both sections are 50?. Inspected freezer evaporator and there is no price pattern. Customer states it has slowly gotten worse over the past month. Sent pictures into TV/service management there is likely a leak in the refrigerant system. Seal system will need to be redone, They are 600 kit the process valve the dryer the compressor and the evaporator for parts; ordrng 1 R600kit and 1 W11580057 (Compressor) and 1 W11546605 (Evaporator) and 1 W11632924 (Condenser) and 1 Sf8404 (Stub)"

Arrived on site for range not allowing oven to heat. Upon arrival confirmed issue. Found cause of failure was loose connection on element wire leading to arching and element burnout. complete repairs with new bake element and wire connector

"Arrived on site for cooling complaint. Compressor running no air flow,found evaporator fan not running,ran diagnostics fan not powering on,checked voltage at liner harness reading 12.6vdc power at harness diagnosed a defective fan motor,ordering a new fan motor,informed customer part is on backorder and we will place the order. ; ordrng 1 W11578030 (Evap fan motor)"

"Arrived to instal diagnosed parts. I removed and replaced both actuator and the separator assembly. I tested the unit and all functions were present. I removed debris from the condenser and then squared and set the chassis. The FC door would not self close and after adjusting and lubricating the slides, the issue was resolved. Operational test good, no leaks observed during service.

"Arrived on site replaced left front switch . Tested unit and all rings on element are heating . No other issues found . Job complete."

"Arrived on site and inspected dryer and found gas flow sputters after it has ignited. After replacement started dryer on a normal cycle and it is no longer sputtering, job complete"

Arrived onsite for GE cooktop not lighting. On inspection the back left burner would spark and ignite the burner. The rest of the burner will not spark. You can get the left back burner sparking and the rest of the burners will ignite while the left back burner is sparking. The other burns will not spark individually.

"Arrived to inspect softener not dispensing. I found the softener cup had residue within it that was diluted with water. I removed and replaced the valve assembly and tested. Operational test good, no leaks observed during service.

"Arrived on site for a dryer that is not heating. Inspected unit and work area. Check voltage to the unit and found proper voltage in larity. Disassembled the unit and tested all heating components. Found the element open. Replaced the heating elements and tested the unit. The unit began to work and operate as designed. Call complete."

"Arrived on site. Removed front cover found broken wires on grid cutter ran diagnostics lower pressure from valve and valve making odd noise,unit passed all other diagnostic test. Replaced valve under appliance express 1 year warranty,installed a new grid cutter ran diagnostics good water flow.

"Arrived on site for defective compressor. Removed compressor and filter drier,installed a new drier found broken cap tube in liner wall called tech support sent pictures to tech support SR#7734974826"

Arrived on site to replace previously ordered parts for washer. Replaced lock assembly and tested unit. Found all is functioning properly at this time and no leaks were found at time of service.

"Arrived on site for dryer tripping breaker as soon as its plugged in .power cord is properly hooked up . Went thru element and fuses , wire harness . All checked normal. Recommended having electrician change out gfi breaker .

Arrived onsite for unit not heating. Upon arrival inspected unit. Heater is not energizing. Check polarity and is good. Inspected heater and is good. Found thermostat is open. Need to replace thermostat. Replaced thermostat and test unit. Unit now operates as designed.job complete.

"Arrived on site for no ice. Diagnosed a defective icemaker,removed icemaker installed updated icemaker kit,reassembled unit icemaker ran through a cycle and filled with water.

"Arrived on site to install previously diagnosed and ordered parts. Due to both blower failures, I removed and replaced the blowers and tested and unit is operating as designed. Job completed."

Arrived on site to test unit for not cooling properly. Found evap motor running. Compressor running but burning hot. Found restriction in evap. Low side pressure was at 20 and 225 on high side. Customer going to call LG and see if they would be willing to repair.

Arrived onsite for dryer rattle. Sounded like blower housing noise. Found unit clean and well maintained. Found worn penny in the blower housing base. Cleaning blower housing and verified the blower is not cracked. Advised customer on findings.

"Arrived on site for washing machine, not filling properly and the drain pump staying on. I plugged the unit in and canceled the drain. I entered diagnostics and found no fault codes. I ran a diagnostics cycle and found the unit filling with water, agitating and draining. When the unit went into a spin I could hear cpscreeching from under the unit. I gained access to the gear case and found it leaking, I also found the belt slipping on the cam pulley. The gearcase, pulley and belt all need to be replaced.

Arrived onsite to install previously diagnosed part upon arrival I installed new bracket. And tested unit several times and found unit dispensing both water and ice normally. Job complete no leaks.

Arrived on site to diagnose a dryer that is not starting. Tested all parts and components and no failures were found at time of service. Advised customer on findings and no further repairs needed.

Arrived onsite for a washer that has a mildew smell. Upon arrival I removed the top of washer and cleaned the tub ring and the inside of the cabinet and found that the smell was gone.

Arrived onsite to replace tube connector. Replaced connector and tested. No leaks present at this time. Job complete.

Arrived onsite to inspect dryer. Upon inspection I found that the unit had good airflow. It tumbled great no noise. And it heated well. I the inspected the inside of the unit and found that the belt looked good and there was Minimal Lint buildup. Job complete

"Arrived to inspect dishwasher not anchored. The original mounts were damaged and one of the screws was missing. The original anchor holes were stripped out. I replaced the mounting hardware and reinstalled the unit. I set the correct leg height and tested. Operational test good, no leaks observed during service.

"Arrived on site for not dispensing water. Removed filter installed by pass same issue not dispensing water good water pressure at filter head,removed drawers found frozen water tank.

Arrived on site to diagnose a range that is not baking properly. Found bake ignitor faulty and replaced it. Tested unit and found all is functioning properly at this time.

Arrived onsite for a washer with key stuck under the wash plate. Upon arrival I removed the wash plate to retrieve the key and reinstalled the plate and tested the unit and found that unit operating as designed.

"Arrived on site and inspected ice machine and found cutting grid is broken and there is a sheet of ice on top of it, took pictures. Recommended to homeowner replacing cutting grid,

Arrived on site to test unit for no display. Test unit and found bad console. Replaced console under 5 year warranty Test unit and unit test good all cycles working correctly job complete

"Arrived on site to diagnose dryer not powering on. On arrival tested unit and found no response from the user interface. Tested voltage and polarity st terminal block and found only 1 leg present, missing voltage at L1. Advised customer to have an electrician come out and correct the missing voltage. Call complete."

Arrived onsite for previously diagnosed parts. Installed parts and the door latch is working as designed.

"Arrived on site for washer, inspected unit and work area. CX complaint unit leaks foam on some load from the vent on the front load washer. I inspected unit and and tested it and found it not leaking. CX is also on a water softener and I advised to cut down the amount of detergent that they are using to a 1/4. Unit. Is operating as designed and no leaks where observed during service. Job completed.

Arrived on site to diagnose a microwave that is not turning on. Found no power to unit and customer will need electrical issue corrected

"Arrived on site to test unit for F27 error code, tested unit found pump is not disengaging triggering a F27 error code, inspected drain pump and found no blockage, parts are still covered under warranty, replaced pressure switch and ran diagnostics, unit is now functioning properly,

"Arrived on site for dryer, inspected unit and work area. Entered diagnostics and found stored error code F2E1. Tested unit for heat and found it not heating. Disassembled unit and tested fuses and igniter and found thermal cut off open. Replaced parts and tested. Unit is now operating as designed.

Arrived onsite with JR and determined control failure to be the cause of the F6e2 error. Replaced the control. Unit is now operating as designed.

Arrived on site for kenmore elite wall oven baking temperatures being off. I inspected the unit and work area. I put the upper oven into a bake and found it 17 degrees to low when cycling. I calibrated the upper oven properly. I set the lower oven into a bake at 350 and found it cycling 10 degrees low. I calibrated the lower oven.

"Arrived on site to inspect refrigerator not dispensing water and not producing ice. Upon further inspection, I tested the water dispenser and it failed. I removed the filter and retested and the water continued to trickle out. I bypassed the filter and retested and the dispenser operated as designed. I removed and replaced the reservoir/filter head assembly and retested. Unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site. Found main control shutting itself on and off and also loud chirping/beeping noise,diagnosed a defective main control,replaced main control powered unit on compressor and fans powered on

"Arrived on site for dishwasher, inspected unit and work area. Gained access to install new sump and motor. Tested unit and its now operating as designed. No leaks where observed during service. Job completed

Arrived onsite for dryer not heating. Upon arrival inspected unit. Verified supply voltage. Voltage was good. Unit does power on and is tumbling but no heat. Disassembled unit to access heating element. Found element OL. Sensors tested good. Replaced heating element and tested. Unit is now functioning properly. Job complete

"Arrived on site to inspect washer noises. Upon further inspection, I tested the unit in a wash cycle and once the tub filled and began to agitate, the drain pump began to make a whirling/whistling noise. I stopped the cycle and removed the pump from the motor shaft and started the cycle again and the noise was gone. I removed and replaced the pump and retested and the unit is operating as designed. I advised the customer of my findings. No water leaks observed during service, job completed."

"Arrived on site to diagnose dryer that is not drying clothes in one cycle most often. Ran unit and verified unit is heating as designed, but doesn't seem to be venting. Examined airflow with tester, found poor airflow reading. Could see lint around the screen as well, including lint on the back of the screen indicating airflow issues. Could barely feel any suction on the vent. Advised tonhave builder come out and inspect the vents due to an obstruction or failed vent cover. Unit is working as designed. Call complete."

"Arrived on site for no ice. Ran diagnostics weak water flow,pump powered on,good frost formation on evaporator plate. Installed a new valve same issue diagnosed weak water flow to unit customer will need a plumber"

"Arrived on site to inspect microwave noises. Upon further inspection, the customer advised that the noise they hear is a vibration noise. Using my MW tester and and cup of water, I tested the microwave on high for 1 minute. During this time, the unit made normal noises. I tested the microwave with the oven on and still no unusual noises. I tested the microwave several more times with the customer present and could not duplicate the noise. I recommended that the customer take a video with their phone should the noise occur again. No repairs needed at this time, job completed."

"Arrived on site to test unit for drum not spinning, tested unit for failed belt and damaged idler pulley, replaced idler pulley and belt, tested unit unit now running as designed, job complete"

Arrived onsite to install previously ordered parts. Replaced freezer led per special project. Replaced FC led (1)and there is no change. Customer will decide if she wants to call us back for further diagnosis. Job complete

"Arrived on site for dishwasher not drying dishes and door dropping open to quickLy. Upon arrival found no errors in diagnostics, found during testing that element was turning on. Found stable power supply to all hardware. Found left door spring fell out of place leading to door dropping to quickly. Reinstalled door spring and found door functionality restored. Instructed customer on best methods to improve drying capabilities. No leaks present call complete"

Arrived onsite to replace faulty bake element. Replaced element and tested. Tested at target temperature 350 degrees. Unit is now functioning properly. Job complete

"Arrived on site and found no saved error codes, ran automatic test cycle and it completed with no issues. Spoke with techline and ran it again with amp clamp attached. Recorded Drain pump 1.2amps, motor peaks at 8.4 amps then drops to 3.3 amps. This is all normal and techline said to show customer service pointer W11525530 to describe nuisance tripping, job complete. 7734981473"

Arrived on site to test unit for unit smoking. Test unit and found normal smoking for first time use. Ran unit and at 350 and unit test good job complete.

"Arrived on site and found saved error codes F9E1, f3e1, ran diagnostic cycle and found washer is not draining properly. Found drain pump is clogged with a clothing item again, took one picture. After removing it washer is draining properly and no new error codes generated, job complete"

"Arrived on site to install previously diagnosed and ordered part. Due to the diffuser/damper (W11164593) failure, I removed and replaced the part and tested. Unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site to diagnose dryer that was not heating. Ran unit and found it powers on and spins, but generates no heat. Checked safety devices and found all good, heating element good. Checked incoming voltage and found L1 only has 40v present, and missing voltage. Advised customer needs to contact an electrician to come out and resolve the dropped voltage. Call complete."

Arrived onsite to replace PCB board per tech line recommendations. Replaced board and tested. Unit is operating as designed. Job complete

Arrived on site to diagnose an oven that was not heating properly. Tested all parts and components and found no failures to unit at this time. Advised customer on findings and possible causes of issue.

"Arrived on site to follow up on washer that was tripping breaker during certain loads. Tested unit and found no error codes present. Ran high speed spin and found no problems present. Called into tech line and performed tech line tests. Found no shorts in unit. Found unit is on a GFCI breaker, which is known to have compatability issues with product under certain loads, SR77344978705. Per SP W11525530, provided info for Eaton breakers to follow up / contact electrician. Unit working as designed. Call complete."

"Arrived on site to test unit for Loud squeaking noise at the beginning of cycle, tested unit found squeaking noise coming from motor mount, applied sound pads to dampen the sound, also idler pulley was not turning freely removed wheel and cleaned the shaft, replaced idler wheel from car stock, tested unit unit is now running as designed, no leaks detected job complete"

Arrived onsite and repaired broken harness. Using truck stock w11335100 Unit is now operating as designed.advised customer on repair. All checks good. ; used 1 W11335100 ( Lower harness) from stock

Arrived onsite to perform sp W11540964 - Special Project S17304. Upon arrival I installed new heating element and tested unit and found unit operating as designed. No leaks Job complete

Arrived on site for washing machine going out of balance. I inspected the unit and work area. The customer provided a video of what was happening. I inspected the gearcase and hub. I found both in good condition. I tested the suspension and found them uneven. I replaced the suspension and retested. The unit is working as designed. Job complete.

Arrived on site to install previously diagnose timer belt switch and cycling stat. Upon arrival reconfirmed issue and installed required parts then reassembled and tested unit and found dryer working as designed. Call complete

Arrived on site for oven not heating properly . Ran diagnostics and found oven was about 25-30 lower then temp probe . Got into calibration and found unit calibration set for 30. Reset calibration to zero and reran calibration. Unit is within heating range now .Job complete

"Arrived on site to replace previously diagnosed FC door, replaced door, tested ice maker, all components are working properly, job complete"

"Arrived on site and inspected range and found all burners are working properly. Issue customer has is them turning off and on while she is cooking. Explain that this is due to a safety standards implemented in 2018, UL 858. Range elements are operating normally and cannot be adjusted or changed, job complete"

"Arrived on site to test unit for filter not locking in place properly. Found 3 metal rings sitting underneath filter preventing it from locking in place. Removed obstruction, unit works as designed. Job complete."

Arrived on site for whirlpool range leaking gas. I inspected the unit and work area. I used the gas detector and found the leak at the line at the wall. I found pipe dope was used on the compression fitting side of the line not allowing it to compress and seal. I removed the pipe dope and cleaned out the threads. I reattached the line and monitored the line for several minuets. It is no longer leaking. Job complete.

"Arrived onsite to replace suspension , washplate and hub assembly. After replacement calibrated and tested unit. Unit is functioning properly. Control is not an issue. Job complete"

Arrived on site for an ice machine that is not making ice. Inspected unit and work area. The customer advised that the unit was slowing down ice production and then completely quit. The unit was in the middle of making ice and I heard the recirculation pump having a hard time recirculating the water due to low water inside of the reservoir. Ran the unit through diagnostics and found the unit barely filling with any water when the unit was trying to fill the reservoir. Removed the filter and found immediate water flow difference. Had the customer replace the filter and found water flowing and operating as designed. Ran through a nice making cycle and found the unit filling and operating as designed. Call complete.

"KRFC704FPS04 Arrived to instal previously diagnosed and ordered part. I re-formed the gasket due to common shipping folding and subsequent deformation. The gasket being able to be successfully re-formed, I installed and tested. The chassis required light squaring and adjustment. Operational test good, no leaks observed during service. All funds collected on prior service."

Arrived on site to test unit for door falling. Test unit and found and left hinge. Replaced hinge test unit and unit test good job complete.

Arrived on site to install previous diagnosed parts. I gained access to the actuator and replaced it with new. I replaced the control and calibrated it. I ran a diagnostic cycle and found the unit working as designed. Job complete.

Arrived on site to test unit for no power. Test unit and found tod disconnected not sending power to elements. Secured connection test unit and unit test good job complete.

Arrived on site to diagnose a refrigerator that is making unusual noise. Found icmaker tilted causing cubes in front of tray to be too big. Releveled unit and all is working properly at this time. Also advised customer on expansion noise during defrost. No leaks were found at time of service and job is complete.

"Arrived onsite for a refrigerator that has a broken ice maker again. Inspected unit and work area. Did confirm the customers complaint with the icemaker being bowed and not operating properly. The customer advised that the cubes that were coming out or normal sized and the unit seem to have been running fine for the last three months up until about a week ago. I called Whirlpool Techline due to ongoing issues and spoke to Rich SR# 7734974343. He advised that because the unit is not over filling and creating an ice slab, the issue would have to be something customer related or something odd that is not typical of normal operation. We checked the liner for the door up against the icemaker and did not find any deformities. He advised that the issue could be with the customer putting things up in the ice container to cool them down quickly or issues with excess frost build up around the ice maker due to the door being opened for too long. He advised that there would be nothing within the icemaker itself that would cause this issue unless if it was a failed icemaker but couldnt imagine having two bad icemakers in a row. He advised to replace the icemaker and to call back if any other issue persist. I replaced the ice maker and tested the unit. The unit began to work and operate as designed. Call complete."

Arrived on site to diagnose a washer that is not cycling properly. Found capacitor open causing motor error code. Replaced capacitor and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.

Arrived on site for a washing machine that is leaking. Inspected unit and work area. Did confirm the customers complaint and found two tears in the door gasket. Replaced the Bellow and tested the unit. The unit began to work and operate as designed with no leaks present. Call complete.

Arrived onsite for SAFTEY gas leak. Upon arrival inspected unit and found broken knob for right front burner. The knob is not securely shutting off gas valve. Called SAFTEY with finding. SAGTEY gave SR#7734959772. Customer will order a knob her self. No leaks present at this time. Job complete

Arrived onsite for SEAL AROUND DOOR IS LOOSE AND FALLING APART. Upon arrival inspected unit and door seal has failed. Need to replace seal. Replaced door seal. Job complete

"Arrived on site to test unit for noise, customer stated that during fill cycle the water pipes make a thumping noise, ran test cycle on washer, all components are activating properly and no unusual sound detected from washer, advised customer to call a plumber and possibly look into installing water Arrestors , unit is running as designed no leaks detected job complete"

Arrived on site to test unit for not cooling properly. Found evap completely frosted over restricting air flow. Found brown connection to defrost element was popped out of molex connection. Secured connection and taped. Unit working as designed. Advised customer to leave unit unplugged and allow to thaw properly for 24hrs to ensure evap does not frost over again. Job complete.

Arrived on site to replace previously ordered parts for washer. Replaced control and motor and tested unit. Found all is functioning properly at this time and no leaks were found at time of service.

"Arrived on site to test unit for no ice production. Found ice maker mold had ice in it but icemaker not responding. Replaced icemaker, unit working as designed. No leaks detected. Job complete."

Arrived on site to resolve outer glass and name plate. Replaced both parts test unit and inky test good job complete.

Arrived on site to diagnose a refrigerator that is not cooling properly. Found hollows in cabinet of unit and heavy moisture build up freezing air channels shut. Insulation failure can not be repaired and unit will need to be replaced. Left message for owner but couldn't reach them to inform them on findings.

Arrived on site to replace both racks and pads. Replaced all parts test unit and unit test good job complete.

"Arrived on site for a refrigerator that is making different size cubes and is clumping ice. Inspected unit and work area. The customer advised that ice is clumping inside his ice container and its causing him not to be able to dispense ice. Did confirm the customers complaint and found the fill cup on the icemaker frozen over causing the issue with water leaking into the icemaker and ice bucket. Removed the ice buildup and tested the unit. The unit began to work and operate as designed. The customer also complained about his unit tripping the breaker when it was on the plug behind the refrigerator. He had the unit plugged into another outlet and advised that the unit has been working ever since on that outlet and extension cord. I checked his breaker box and found that the plug behind the refrigerator was a part of a series of kitchen plugs inside the kitchen and the lights above the kitchen. Did advise the customer that it is most likely that when the unit is playing the highest amount of amperage and other things are being plugged in and running, it is over-amping the breaker. With the unit not tripping the other breaker that they have the unit plugged into for over a week, it would indicate that the issue was not with the refrigerator. Advise the customer to get a dedicated circuit to his refrigerator for this issue to correct his problem. Call complete."

Arrived on site to test unit for F3E0 error code. Test unit and found bad control board. Replaced board test unit by heating to 375? and unit test good job complete.

Arrived on site to install previous diagnosed parts. I installed the new insulation. I ran the unit and found the noise has been lowered to acceptable ranges. Job complete.