"Arrived on site and replace spark module, cooktop will now stop igniting once burner has lit, job complete

Arrived onsite for a cooktop to replace previous diagnosed parts. I replaced the left center and center burner valves. I cleaned the orifices. I tested the cooktop and all is working as designed. There were no gas leaks present at the time of service. Call complete.

Arrived on site to test unit for unit not finishing cycle. Test unit and found bad control board shutting off. Will need new board customer

"Arrived to inspect door stuck shut and error code. The unit showed F21 steadily upon arrival and the door was stuck shut. The unit had failed several days prior and I had to remove a regular load of clothes water from the tub. I found the drain pump would not engage and upon removal, was able to see the impeller was canted and locked up. After replacing the pump assy, the unit operated as designed

"Arrived on site for dishwasher smoking and tripping breaker. Upon arrival confirmed issue and found the cause failure had been the control board spontaneously combusting and catching fire. Thoroughly inspected rest of unit and found no failures in the motor heating element drain motor or valve. I did find however that the main harness was completely burnt and ruined along with the entire main control board and housing it was put in being completely melted. called and reported findings to safety department and spoke with Steve Sr#7735074782, M14YWV0WL1. Customer stated they want to call whirlpool before continuing with any repairs and I provided in the file number to contact whirlpool with. Call complete"

"Arrived on site for lint screen and housing broken. Replaced housing and lint screen . Cleaned lint out of dryer .

Arrived onsite to replace the previous diagnosed parts. I replaced the upper convection fan and the upper temperature potentiometer. I calibrated the oven and tested. The upper oven is working as designed Call complete.

Arrived onsite and found unit unplugged and in storage opened evap cover and found one of the harness clips to the heater backed out and shorting the circuit. Restored connection. No parts needed. Advised maintenance on repair.

"Arrived on site to install previously diagnosed and ordered part. Due to the RC ice maker leaking, I removed and replaced the ice maker and tested. Unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on smite for cooktop, inspected unit and work area. customer complaint was same issue from last time. Had error code f47. Powered unit off and replaced the module. I then programmed it to #23 and and tested. Unit is now operating as designed. Job completed."

Arrived onsite and found oven door gasket failed allowing heat to escape. Replaced gasket and tested. Unit now functioning properly. Job complete

"Arrived onsite and repaired, the unit by replacing the bin. Unit is now operating as designed. All checks good."

Arrived on site to test unit for RC not cooling properly. Found thermistors in range. Found damper opening and closing as designed. Unit would cool then go into defrost cycle every 3mins. Per service pointer W11512008A replaced control. Unit starting to cool. No leaks detected. Job complete.

Arrived on site to test microwave not working. Its not a combo unit microwave its separated from the oven. Did not work on unit did not collect anything

Arrived onsite for freezer freezing over. Upon arrival found temperatures ideal. After inspection found fill tube to ice maker pinched and causing water to leak in cabinet and freeze. Corrected fill tube and tested. No leaks present at this time. Unit is functioning properly. Job complete

"Arrived on site to install broken/ missing part, customer received oven vent and it needed to be installed, installed vent, job complete"

Arrived on site and replaced previously diagnosed console. Unit now working as designed. Advised customer to connect unit to WiFi. Job complete.

"Arrived on site for dryer, inspected unit and work area. customer complaint was dryer not drying. Tested unit and found the vents clogged and unit not heating. Disassembled unit and tested the element and it showed open. Replaced element and used my shop vac to clean all debris inside unit. I recommended customer to get vents cleaned. Unit is now operating as designed."

"Arrived on site to replace previously diagnosed control, HV control, LED control, deli UI,Control UI, ice box fan, RC evaporator fan harness and support, FC evaporator motor harness, replaced parts tested unit the pulsating on the 12 volt Circuit is now gone, evaporator developed a good frost pattern, at this time unit is running as designed, customer will monitor and if any issues return will call us back, no leaks detected job complete"

"Arrived on site to inspect washer not responding. Upon further inspection, I attempted to place the unit in diagnostics and the control panel failed to respond. I tested the control panel harness and it is good and found the service LED flashing on the main control. I removed and replaced the control panel (W11319991 ) and retested and unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site to inspect refrigerator no cool. Upon further inspection, I found the Fc evap cover engulfed in frost/ice. I checked the bottom of the FC door at the gasket and chassis and found that there is still a gap causing airflow into the freezer section. I placed the unit in diagnostics and tested defrost and it is operating as designed. Checked the defrost thermistor and it is good. Contacted techline and spoke to Andrew and provided the SR number and sent another photo of the gap. Andrew advised that the file would be sent for review and attached to the same SR#7734912856. I advised the customer that they would normally hear from someone within 24-48 business hours but due to the holidays, it most likely wont be until the following Monday. Unit will need to be defrosted again. No water leaks observed during service, job completed."

"Arrived on site and inspected microwave and found fan blades are making noise while spinning. Removed vent cover and found debris stuck in fan blade. After clearing fan blade it is now quiet and running normally, job complete"

"Arrived on site for control buttons frozen . Found control unresponsive . Removed control and found control wasnt properly set in housing and button control wasnt pushing on control. Shifted control into proper position . Now control is responding to commands . Double checked and no ice or frost in either sections . Couldnt duplicate any issues with ice maker or dispenser at time of service . No water leaks detected at time of service. Called tech line , same sr #. Job complete."

"Arrived on site for washer needing previously diagnosed control, gearcase, and slider. Upon arrival reconfirmed issue and installed all 3 parts. Reassembled and tested unit. Found no failures, leaks, or errors. Informed customer unit was ready for use. Call complete"

"Arrived on site to replace valve found water shut off at wall and line was kinked . Unlinked supply line and turned water on. Ran harvest , All checked normal. No water leaks detected at time of service. Job complete"

Arrived on site for dryer not turning drum. Upon arrival confirmed issue and found belt had broken. After inspection of other hardware I replaced belt and found dryer functioning as designed. Call complete

"Arrived on site for a dryer that is not operating. Inspected unit and work area. The customer advised that whenever he tries to start a load, the unit does nothing. Checked voltage at the wall and found proper voltage with the unit idle. Checked the thermal fuse and found it showing continuity. Tested voltage from line one to neutral When they push to start was pressed and found voltage dropped from 124.4 V down to 1.6 V. Tested voltage on the line two side to neutral and found voltage go from 124.4 V to 244 V. Check voltage at the plug and confirmed the same issue. Advise the customer that his problem is an electrical supply issue and will need to be corrected to fix his issue. The unit is working as designed. Call complete."

Arrived on site to test unit for steam sprayer staying on. Customer stated she never used steam feature. Removed water supply from dryer. Ran ventilation test and found air circulation restricted. Advised to have venting leading to exterior cleared. Job complete.

Arrived onsite for washer making noise is agitating cycle. Upon arrival inspected unit. Put unit in diagnostics and found no stored error codes. Ran test cycle and could hear noise. Disassembled unit and found obstruction in between drive shaft and agitator. Removed obstruction and tested. Unit is now functioning properly. No excessive noise at this time. Job complete

"Arrived on site for loud noise. Customer played recording of noise,diagnosed noise from recirculating pump,replaced defective pump ran new pump no odd or loud noise from pump."

Arrived on site to diagnose a dishwasher with an upper sprayer that melted on heater. Found no failures to sprayer mount or manifold. Advised customer a dish in unit may have rotated collar on sprayer causing issue. Replaced sprayer and tested unit and documented with safety. All is working properly at this time and no leaks were found at time of service. File# 7735069591

Arrived on site to diagnose a washer that is making unusual noise. Found belt slipping and cam damaged. Replaced both parts and tested unit. Found all is functioning properly at this time and no leaks were found at time of service.

"Arrived on site to diagnose refrigerator that was not cooling in either compartment. On arrival unit was unplugged. Customer said they had noticed some frost on the evaporator cover, which likely means it had a defrost issue. When I moved the unit to give it power I did find water on the ground, so pan was full. When plugged in unit is cooling properly. I checked the defrost circuit and found the connector for the brown wire for the heater unseated, so heater could not be powered. Repaired connector and tightened. Unit should now be working as designed. Customer advised to leave unit in failure state so we can more accurately troubleshoot if issue returns. Call complete."

Arrived on site and replaced previously diagnosed harness. Unit now working as designed. Job complete.

"Arrived on site to replace previously diagnosed UI, replaced UI tested unit unit now functioning as designed, job complete"

"Arrived on site and found freezer door switch is jamming, Replaced freezer switch and Discussed with customer possibility that it may get frost in it which could also cause it to get stuck. At this time no one is working properly, job complete"

Arrived onsite for a washer that is still tearing holes in the clothing. I found the wash plate bolt that was tightened on the previous visit still tight. I inspected the entire inside of the basket and wash plate. There are no burrs in the unit. I went ahead and changed the capacitor per techlines recommendation on the previous visit just in case it is breaking down during use. Before replacing the capacitor I tested it again and it showed 45mf. I ran a calibration and a diagnostics cycle. The unit completed the cycle and worked as designed. No water leaks were present at the time of service. Call complete.

Arrived on site to test unit for flames to high on low. Adjusted all burner flames test unit and unit test good job complete.

"Arrived onsite for f3e2 and tested sensor bars from the control and found proper continuity. Inspected vent to the outside for proper airflow and determined airflow is good. Advised customer on findings and cleared error codes. Customer stated mostly not drying towels and throws using sensor cycles. Advised customer on using timed dry with custom settings for thorough drying of larger items, as there can tend to be premature end times with towels and bedding. All else checks good."

Arrived on site for refrigerator not allowing mullion bar to shut properly when closed. Upon arrival confirmed issue and found spring in bar failing. Replaced mullion and tested door. Found unit closing and functioning as designed. Call complete

Arrived on site to test unit for not drying properly. No stored error codes. Ran diagnostics with no issues and verified element engaging with proper voltage. Advised customer on use of jet dry and purging cold water prior to starting unit. No leaks detected. Job complete.

Arrived on site for a dishwasher that is leaking. Inspected unit and work area. Did confirm the customers complaint and found the pump and motor not sitting properly inside of the dishwasher. Went to set the washer motor in place and found that the brackets holding the wash motor in place were broken. Replaced the wash motor assembly and tested the unit. The unit began to work and operate as designed with no leaks present. Call complete.

"Arrived on site for microwave, inspected unit and work area. customer complaint was the microwave not heating. Tested unit and found it not heating. Removed unit and found bad magnetron and capacitor was reading to specs but it looked inflated. Replace mag, cap, and diode. Unit is now heating and operating as designed. Job completed."

Arrived on site for refrigerator not allowing lower door to seal. Upon arrival confirmed issue and found cause of failure was door to door being misaligned on hinge. Adjusted door and found unit sealing as designed with no failures. Call complete

Arrived on site to replace compressor for refrigerator. Replaced compressor and filter drier and followed r600 procedures for vacuum and charging. Tested unit and found all is functioning properly at this time. No leaks were found at time of service.

Arrived onsite to replace previous diagnosed parts and to check the unit for no ice. I replaced the left and right pantry door gaskets. Ms stated the icemaker never made ice. I found an E5 error. I ran the harvest and fill test and all worked as designed. I tested the fill tube heater and found it good. I found the icebox fan working as designed. I replaced the icemaker. There were no water leaks present at the time of service. Call complete.

Arrived on site and found customer intermittently experiences drain error. Found both dishwashers are sharing a drain connector to garbage disposal and there is also a reverse osmosis system training here as well. Showed customer that This is likely the cause of their experience. Left dishwasher also does not have a high drain loop. Reverse almost this train will need to be relocated. Documented installation type with tech line 7735105701

Arrived on site for range flashing error code . Found control not responding to any commands . Replaced ui main control. Tested all burners and preheated oven . Job complete.

"Arrived on site for a washing machine that is not filling with water. Inspected unit and work area. Tested the unit in manual filling and found both hot and cold not pulling in any water. Checked water pressure on the cold water valve and found proper water pressure. Checked water pressure on the hot water valve and found no water coming through whether the valve is open or not. Went ahead and replace the water valve but did explain to the customer of that without hot water, she may still encounter issues. Advise the customer to try the unit on top cold for the short period until they get their hot water supply issue fixed. Tested the unit and diagnostics and was able to get cold water to flow properly through the washer. All other functions of the unit were working as designed. The unit is now working as designed. Call complete."

Arrived on site to install new double valve due to recently replaced valve failing. Replaced valve and tested unit. Verified unit working as designed. Call completed with no water leaks.

Arrived on site to test unit for pots not working. Found customer no using induction cookware. Job complete

"Arrived on site to test unit for RF burner constantly clicking, center front burner flames not changing and LF burner no simmer. Found both outside front burners had summer orifices clogged. Cleared restriction and adjusted center front flame height. Unit now working as designed. No leaks detected. Job complete."

"Arrived on site to test unit for no drying dishes, put unit through diagnostics, all components are activating properly, heater is engaging, stated to customer to use rinse aid at all times and prop door to allow it to air dry, unit is running as designed no leaks detected job complete"

Arrived onsite for door hinge needs replacement. Upon arrival inspected unit and found left rear ofAnd found that left rear corner of lid has failed. Inspected and tested hinges and are goo. need to replace lid. Replaced lid and the lid. Lid open and closes correctly. Job complete

Arrived onsite for - SP W11632927 - Special Project S153AWB. Talking with the customer and the experience he was having with the unit I replaced the Capacitor on the unit. customer said that the noise was happening at the beginning of the spin cycle. Tested unit and it is working as designed. No water leaks detected during service.

"Arrived on site to install previously diagnosed parts. Inspected unit and work area. Replaced the compressor, dryer, and coupler. Ran the unit under a vacuum for 15 minutes and found the pressure hold for 15 minutes. Charge the unit up with 56 g of R600. Tested the unit and found the unit cooling and operating as designed. Advised the customer to keep an eye on the unit over the next 30 days and the car back if any other issues persist. Call complete."

"Arrived on site for refrigerator needing previously diagnosed control, harness, and thermistors. Upon arrival confirmed issue insured all ice was gone from evap coil and installed parts. Informed customer to give unit 24 hrs to cool. Call complete"

"Arrived on site to follow up on washer that leaked immediately following service. I thoroughly examined the area in and around the washer for leaks. I found no water leaks in the rear of the unit or the drain. I found water and soap trails coming from the bellow area due to large amount of crust and hair on the door and bellow. I ran the unit with the lid off and checked for leaks. Found a slight drip coming from the steam box pressure hose around the clamp. I adjusted the clamp to stop the leak. I also cleaned the bellow to allow for a better seal. I ran multiple cycles including a clean washer cycle for over an hour and did not get any other leaks from the unit. Unit had a large amount of suds, likely due to old soap buildup which can get in the pressure line and trigger the IE error. TG also informed the customer of the very low pressure he verified at times during the cycles, which needs a plumber to resolve. Low pressure can also trigger the IE error, which is a pressure / water error. Advised customer to run cleaning cycles to remove soap buildup and unit should return to normal function. At time of service completion there were no codes or leaks found. Call completed."

Arrived on site to replace door for refrigerator. Replaced fc door and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.

Arrived onsite for previously diagnosed parts. Installed magnetron & diode in the unit. The customer had a video of the MW making a loud noise. The noise sounds like the magnetron was struggling.

"Arrived to instal previously diagnosed and ordered parts. I evacuated the system and then removed and replaced the compressor, service port and dye drier. I vacuumed the system and found inconsistencies with readings and then pressurized the system and tested. After finding no leaks in either evaporator or within any accessible tubing, I re-vacuumed and then charged the system. The unit started cooling and I advised the customer to contact us if there are further issues. No leaks observed during service."

Arrived on site to replace previously ordered parts for range. Replaced control and tested unit. Found all is functioning properly at this time.

"Arrived on site to install previously diagnosed parts to resolve dead microwave. I checked voltage at the control and was able to find a reading of 120, but unit would not power on. I checked and also found 91v at neutral. Replaced the control and filter board. I checked the outlet and found its only reading 82v on my voltage tester. I tested the unit on another outlet and found it working as designed with no issues. Microwave outlet is bad, causing the unit not to work properly. Advised customer to have an electrician come out and fix the outlet, and can use the unit on an extension cord. Unit now working as designed. Call complete."

Arrived on site to install previously diagnosed heart. Inspected unit and work area. Replaced the evaporator fan assembly and tested the unit. The unit began to work and operate as designed. Call complete.

Arrived on site to test unit for center burner not working. Test unit and found bad burner head. Replaced burner head test unit and unit test good job complete.

"Arrived on site for water not dispensing. Found water line freezing,decreased temp setting to prevent water line freezing in fresh food compartment"

"Arrived on site for no cool. Replaced evaporator,3 way valve,solenoid and evaporator,vacuumed system down unit kept vacuum recharged system to manufacture spec powered u it on checked low side pressure good."

"Arrived on site to inspect dryer drum not turning. Upon further inspection, I tested the unit and found the drum not turning. Disassembled the unit and found the belt had flipped over and the smooth side was on the drum side and not providing any grip for the drum to turn with a load. Corrected the belt and retested and reassembled the unit and retested again. Unit is operating as designed. No lint observed during service, job completed."

Arrived onsite and replaced parts per diagnosis. Found gasket needed only to be heat treated to resume the proper shape. Unit is now operating as designed. Advised customer on repair.

"Washer is in a barndominium next to a winery, it is the large silver building on the right. Arrived on site and inspected washer and found all functions are operating properly but there is no water flow from hot water. Found hot water was off and customer was attempting to use a warm cycle. Turn hot water back on and it is now working properly. Informed customer that if they only want to use cold water tap cold setting is the only option that will complete a cycle. Job complete"

"Arrived on site to diagnose washer that was not starting cycles. On arrival tested unit and found unit responsive. I found the water hoses backwards and only hot turned on. Swapped hoses and ran test cycle. Verified all working as designed, with no verifiable issues. Call complete."

"Arrived on site to test unit for no power, tested unit found unit did not have a power cord installed, installed power cord provided by customer, powered on unit but no heat, checked voltage and found unit is not receiving proper voltage, advised customer to hire a electrician to address this issue, at this time job complete"

Arrived onsite for will not turn on. Upon arrival inspected unit. Console is not responding. Checked polarity and is good. Got correct voltage from control to console. Need to replace console. Replaced the control panel W11413567 and test unit. Unit operates as designed. Job complete

"Arrived onsite to install previously ordered parts. Replaced control W11546690, harness W11546681, and thermistor WPW10384183. Test unit and unit now goes into defrost . Job complete"

"Arrived to inspect ice dispensing continuously. I found the actual issue with the unit was the auger motor for the ice bin was that part running and the ice being dumped out was actually due to the pressure of the ice from the auger and not from being commanded open by the UI. I tested at P13 of the main board and found a closed circuit to the auger motor at all times, allowing line VAC to pass through anytime the door switch was closed. No leaks observed during service. ; ordrng 1 WPW10404689 (Main Control)"

Arrived on site for washer giving IE error towards end of cycle. Upon arrival confirmed issue and found cause of failure was cold side inlet valve. After getting customer authorization made repair and tested unit on 3 cycles and verified no errors were occurring. No leaks present. Call complete

"Arrived on site for washer, inspected unit and work area. customer complaint was washer not draining or spinning properly. Stored error codes F0E3 F8E1 F2E1. Called techline and spoke with Andrew sr#7735110171 and suggested to replace control board. Im ordering control and scheduled customer to return on 11/30/22 and office will contact customer with time frame. No leaks where observed during service.

"Arrived on site. Removed front cover found ice slabs made and sitting on grid cutter,found broken wire on fgrid cutter and found water leaking from drain cap. Unit will need a new cap and grid cutter ; ordrng 1 WP2185696 (Cap) and 1 WP2313637 (Grid cutter), states that autho needed"

Arrived onsite and found fresh food sectionn 65 degrees. Found freezer at 10f. Found evap frozen through with over an inch of ice. Called techline to report findings. Spoke with Bruce and with drew. Sr#7735106970 found thermistors in range and found the heater circuit open line from the control. Ordering sealed system repair to replace evap and heater assembly. ; ordrng 1 R600 (Evap heater circuit open line from control) and 1 R600 (LOKRING required Aluminum cap tube)

Arrived onsite for a refrigerator not cooling correctly in either compartment. I found out the unit is getting partially cold in the FC but the RC is at room temp except at the bottom. I found 123VAC to the evaporator fan and its not running. The fan will need to be replaced. The customer will not be back until December 25th. Ordering WP2315549 evaporator fan. Office to RS.; ordrng 1 WP2315549 (Evaporator fan)

Arrived onsite for Broken or Missing Parts. Upon arrival inspected unit and found ice tray detached from icemaker. Need to order icemaker. ordrng 1 W10873791 (Ice maker)

"Arrived on site to inspect dishwasher not cleaning dishes. Upon further inspection, the customer advised that the drain screen is missing and the lower spray arm is not attached and the unit is not cleaning the dishes well. I inspected the unit and found the screen missing and the lower spray arm not attached properly. Re-attached the spray arm and placed the unit in diagnostics showing error code F7E1-incoming water temps too low. I cleared the code and continued with testing. I tested amp draw at the harness mat the junction box and found the element is showing 7-9amps during wash and drying cycles of diagnostics. All of the other components are within amp draw range as well. Customer advised that they have a water softener system. I made recommendations for use and care, as well as, detergent and rinse aid use (see photo of LBH). No water leaks observed during service. Returning tech see sticky note; ordrng 1 WPW10463906 (Screen)"

"Arrived onsite for Not Cooling - Both Sections . Upon arrival inspected unit and found compressor energizing , then turning off after a couple seconds. Test compressor and found common to ground showing resistance. Contacted SW for assistance. Suspecting a burn out. Returning tech Check for possible burnout. This is a r134a system.Ordering complete sealed system components including compressor,evaporator,condenser,access valve,UI drier, nitrogen, tube kit. Office to reschedule ; ordrng 1 WPW10466675 (Compressor) and 1 876765 (Tube kit) and 1 WPW10608485 (Evaporator) and 1 W10559262 (Condenser) and 1 Nitrogen (Nitrogen) and 1 WPW10143759 (UV drier) and 1 W10913906 (Access valve)"

Arrived on site for fridge making rattling noise . Found compressor feet failing and allowing compressor to rattle . Ordering feet . No water leaks detected at time of service. Call to set return ; ordrng 4 W10806346 (Compressor feet)s

Arrived onsite for a freezer with the over temp light staying on. I checked the temp inside the freezer and found it at 0 degrees and the over temp light was on. I could not get the over temp light to reset using the control. I cycled power and was able to get it to reset and turn off. The customer stated that they did reset the light but after about three hours it had come back on. The customer stated that nothing in the freezer has ever thawed or become soft. I explained to the customer that I would order another control and to monitor and see if the light comes back on. If it doesnt turn back on then it should be good and the call should be cancelled. Ordering W11579401 control. Office to RS.; ordrng 1 W11579401 (Control)

"Arrived on site to diagnose oven throwing an F1E0 code. On arrival found code is present, which is a code for display board failure. I was able to cancel the error and check in diagnostic mode, and found an F2E1 error for stuck key. Ordering a console / UI assembly to resolve. ordrng 1 W11600643 (Control Panel)"

Arrived on site to test unit for no ice production. Found water level sensor thinking reservoir is full when empty. Also found compressor kicking on and off intermittently. Recommend compressor replacement. Needing 2hrs and SS tech on return visit. ordrng 1 WPW10605286 (Compressor) and 1 WPW10200037 (Dryer tube) and 1 W10913906 (Access)

Arrived on site for water still leaking from washer . Ordering per service pointer W11651001 new tub ring . Also reordering faucet switch assembly and bezel . Call to set return . C-NOTE ; ordrng 1 W11094304 (Ring tub) and 1 W11094976 (Bezel) and 1 W11175629 (Faucet switch)

Arrived on site for right front burner not lighting or taking long time to ignite . Found bottom of cap rough and not allowing cap to sit properly . Ordering caps . No gas leaks detected at time of service. Call to set return ; ordrng 1 W11121390 (Caps)

"Arrived on site to diagnose refrigerator that was not cooling in either compartment. Examined unit and found warm Temps on both compartments. Compressor was not running at time of service. Could hear the start device clicking and compressor not starting. Checked compressor and found it was hot and locked up, due to sealed system failure. Verified lines are steel and not aluminum, no lok rings needed. Ordering R600 sealed system parts. Office to schedule.; ordrng 1 W11635510 (Compressor) and 1 R600Kit (R600 Kit) and 1 W11546692 (Evap) and 1 Wpw10143759 (Dryer) and 1 W11506635 (Access Valve)"

"Arrived on site and found bake cycle will trip gfci on right oven only. Broil cycle works fine. Left oven bake works fine. Checked ignitor wire for damage and it is fine. Spoke with tech line and they recommended replacing control board. After replacing powermax control nothing changed. If bake is started with door open it will ignite but as soon as door is closed gfci trips. Same with convection bake. Broil, and convection roast work fine and do not trip gfci. Spoke with techline again and the recommended replacing UI, will also bring DSI and power max extension. 7735110870; ordrng 1 W11355250 (Control) and 1 W11406541 (Control)"

Arrived on site to test unit for not keeping temps properly. Tested unit and found no issues with unit. Advised against using hanging thermometers as they cannot keep up with temp fluctuations. Job complete.

"Arrived on site for cooktop, inspected unit and work area. customer complaint was cooktop broken. customer states cooktop was broken when delivered. Cooktop was uninstalled and unable to test. I explained to customer we will need the unit to be installed before we return to install glass. ; ordrng 1 W11051484 (Cooktop glass)"

"Arrived on site to test unit for no ice production, customer stated that RC is not cooling also, tested unit found defrost system failed, FC evaporator cover frozen over, ran ice maker through diagnostics, ice maker completed cycle and filled with water, defrost issue is effecting ice production, will need control box, FC thermistor and evaporator harness, ordering parts, office to reschedule ; ordrng 1 W11546609 (Control box) and 1 W11546681 (Evaporator harness) and 2 W10384183 (Thermistor)s"

Arrived onsite for previously diagnosed parts. On arrival found the pump was not working. Installed the pump and tested unit. Got a H20 error pulled the unit back out and found the hose was pinched. I put the unit back in diagnostics mode and was looking for water leaks and noticed water streaming in the right back corner. On inspection found that the unit had a seam that was leaking at the top right corner. Informed the customer that the dishwasher tub needed to be replaced. Ordering a new tub W11409865. There were water leaks detected during service. 3rd party warranty needs to approve the parts. ; ordrng 1 W11409865 (Tub) and 1 W11537778 (Heating element)

Arrived onsite for dishwasher not draining. Upon arrival inspected unit. Found that issue was actually wash motor failed. Unit does fill and drain. Diagnostics showed 4/3 motor failure and confirmed with test. Office to reschedule ; ordrng 1 W11025157 (Sump and motor) and 1 W10906426 (Control)

"Arrived on site for cooling complaint. Found fresh food evaporator heavily incased in ice. Ordering drip pan and harness to cover repair per service pointer,customer will defrost unit; ordrng 1 W11457241 (Drip pan)"

Arrived on site to diagnose a cooktop with a burner not lighting. Found ignitor clip missing and it will need to be replaced to complete repairs. Office to set return appointment. ; ordrng 1 8286863 (Clip)

"Arrived on site for a wall oven that wont turn on. Inspected unit and work area. The customer advised that the unit will turn on but the inside buttons inside of the white screen will not work. Did confirm that the home button, light button, and menu options button were functional but The inner screen would not except any selections. Checked wiring and found all wiring secured and connected. The unit will need a new user interface for repair. Ordering the user interface in the office will need to contact the customer about a return date due to an out of stock and PSP item.; ordrng 1 W11297709 (UI)"

"Arrived onsite for washer not spinning. On inspection found that the unit did not agitate or spin. Checked voltage to the actuator in had 5VDC, checked the cap and it was 45.7u found error F7E5 Installed new actuator. Tested again still no spin cycle. Ordering motor and capacitor W11428524. ; ordrng 1 W11497303 (Motor) and 1 W11428524 (Capacitor)"