Arrived on site for washing machine not starting. I inspected the unit and work area. I found the capacitor out of range. I replaced the capacitor and tested the unit. It is now working as designed. Job complete.

Arrived on site for the dryer showing clean vent error code. I inspected the unit and work area. I used my vent tester while the unit was connected to the exit or vent and is showed poor air flow. When I removed the dryer from the exterior vent I retested the dryer and found air flow drastically improved. Indicating the exterior vent has some kind of restriction or the exterior vent is not opening. The exterior vent needs to be inspected to ensure it has proper air flow for the dryer. Job complete.

Arrived on site for a dishwasher that is still not draining. Inspected unit and work area. Did confirm that the dishwasher drain was low. Went ahead and replaced the drain pump and tested the unit. The unit began to work and operate as designed. Call complete.

"Arrived on site to diagnose dryer that customer says is not fully heating clothes. On arrival customer let me know that it feels like it's heating, just not very hot. On inspection of the unit, I found the eco boost was enabled on their default cycle. Advised customer on making sure eco boost is off when running the unit for best heating. I disabled eco boost and adjusted temp on unit and ran. Verified with customer present rhe unit is working as designed. Call complete."

"Arrived on site to diagnose refrigerator making noise and also freezing items. On arrival customer showed me that some items on the 2nd shelf and 1st will freeze sometimes. I found items were touching the back wall, creating cold pockets. Advised customer they can not block the shelves, or items will freeze. Customer showed me a video of a noisy grinding. Traced to damper making the noise. Replaced damper and verified unit working as designed. Call complete."

"Arrived on site to inspect dryer noises. Upon further inspection, I tested the unit and immediately at start, I could hear a noise coming from the back of the unit. I removed the back panel and retested and found the the noise coming from the blower wheel. I removed the lint chute assembly and found where the blower wheel is rubbing on the chute. I adjusted the chute and retested and unit is operating as designed. No lint observed during service, job completed."

"Arrived on site to inspect dryer error codes. Upon further e, I placed the unit in diagnostics showing error code F4E3-poor airflow. Cleared the code and using my vent test kit, I tested the airflow to the unit. The first 2 tests failed (photos). I checked the vent that goes outside and its a direct shot from the unit to outside and it is clear. I pulled the unit out and remove the vent tube at the back of the unit and found a large amount of lint inside. Removed the lint and using my borescope, I scoped the vent pipe inside the unit and the vent going outside and both are clear (photos). I re-installed the vent tube to the unit and retested and unit vent test passed (photo). I advised the customer of my testing and findings and adjustments. No lint observed at the end of service, job completed."

"Arrived on site and replaced tub and heater diagnosed by previous technician, job complete"

"Arrived on site and found saved error E5 on test 56, ran test 57 and icemaker cycled properly, Replaced it anyway due to possible ice tray thermistor failure. Cycled power to refrigerator at breaker to clear error code. After replacing icemaker ran test 57, test 45, 36, and 15 and they all passed, job complete"

"Arrived on site and found dryer is getting power, display is on but control board just clicks when a cycle is started. Replaced control and dryer is Working and heating properly, job complete"

"Arrived on site for cooktop, inspected unit and work area. Customers complaint was gas leak detected at the gas line to the copper fitting. Used my bubble detector and found leak on the line. I tried to tighten up the gas line but unsuccessful. It was still leaking. Left gas turn off and explained to customer that its a installation issue and they would have to contact the installers."

"Arrived on site for dryer taking to long to dry, inspected unit and work area. Tested unit and had poor air flow. Advised customer to get maintenance from her apartment complex to take a look at the vent. Unit is operating as designed. Job completed."

"Arrived on site for washer, inspected unit and work area. Customers complaint was washer would leave white residue after wash. Entered diagnostics and found error code F0E5. Called techline and spoke to Scott SR#7735394741 and explained to him about what the customer was experiencing. Scott advised to informed customer to turn up the concentration level up to use less detergent. Unit is operating as designed at this time and no leaks where observed during service. Job completed."

"Arrived on site for door seal issues. Found defective right side fresh food door gasket,replaced defective gasket,remolded seal checked door seal good."

"Arrived on site for no water or ice. Diagnosed a frozen water tank,added sealer to gaps between fan scroll and air tower,defrosted lines tested water dispenser passed,ran harvest test passed,ran fill test passed."

Arrived on site to diagnose a washer that is not draining. Found drain pump clogged and cleared drain of all debris. Tested unit and found all is functioning properly at this time. No leaks were found at time of service.

Arrived onsite for washer filling and then not progressing correctly. Upon arrival inspected unit. Ran test and all components are functioning. Ran normal cycle and found that delay soak was selected. Turned selection off and tested. Found unit is now functioning properly. Job complete

"Arrived on site for washer throwing F4E1 error. Examined unit and followed service guide for error. Found resistance on heater is within spec, however the connector was barely seated in the control. I fully seated the connector and tested the unit. Found unit is running on cold wash, however no hot line is installed. Advised customer to get a new hot water line installed to unit to ensure proper operation, and to follow up if issue returns with a functional hot water line. If issue returns, control should be replaced, but as of testing time there are no errors popping up. Call complete."

Arrived on site to diagnose refrigerator that is not cooling. Customer advised me unit said cooling off. Found cooling was disabled from the user interface. Turned cooling back on and verified compressor came on and unit had cooling return. Advised customer on how to turn cooling on and off. Unit working as designed at this time. Call complete.

Arrived on site to diagnose undeveloped dryer that is wobbling when used. Customer advised installers never installed leveling feet on the unit and it's now rocking. Installed leveling feet and leveled unit. Verified its working as designed. Call complete.

"Arrived on site to diagnose dryer that is no longer heating, but took multiple cycles to dry prior. Examined unit and found the cutoff open, thermal fuse open as well. Replaced both parts and tested. Also found a bra wire in the heating element, causing it to ground. After testing verified unit working as designed. Unit is also not venting well, restricted airflow due to clogged vents. Advised unit is now working, but vents must be cleaned or issue will repeat. Call complete."

"Arrived on site and inspected refrigerator and found evaporator is frosted over, took pictures. Found ground wire to heating element is loose inside plastic connector, took picture. After resetting connection put refrigerator into a defrost using diagnostic cycle And took another picture of element heating. Recommended to homeowner that refrigerator be unplugged for two days to allow all ice to melt in freezer. Refrigerator should be operating normally after this, job complete"

"Arrived on site for refrigerator, inspected unit and work area. Gained access to remove old compressor and install new compressor. Braced new compressor, installed new pre cooler, access valve, dye drier and vacuumed the system for 15 min. After vacuuming the system I waited 15 to make sure system had no leaks and I did not lose any vacuum. I charged up the system with R134 5.5oz . Plugged unit in and advised CX to let cool for 24hrs. No leaks where observed during service. Job completed."

"Arrived onsite for washer giving long fill error code. Upon arrival inspected unit. Tested and confirmed code. Cleared code and tested. Found hot Valve making noise when energized. Removed supply hoses and checked pressure, pressure is good. Replaced hot valve . Ran test again and no noise. Ran test cycle and unit is functioning properly. No leaks present at this time. Job complete."

Arrived on site for unit missing trim on control panel. Found customer mistook oven vent for trim and was missing from other side of control panel. Instructed customer on oven vent . No gas leaks detected at time of service. Job complete

Arrived onsite for refrigerator not making ice. Upon arrival inspected unit. Found voltage to ice maker good. Forced harvest and ice maker not responding. Replaced ice maker. Tested unit and unit is functioning properly. Completed harvest and fill. No leaks present at this time. Job complete

Arrived on site for oven not heating . Found red wire on harness had burned out at connector at block . Repaired wire with new terminal connector. Ran preheat . Oven is now heating properly. Job complete

"Arrived on site ,installed light ,switch and icemaker. Light is coming on and responding to switch commands . Ran IM harvest all checked normal. No water leaks detected at time of service. Job complete"

Arrived on site to diagnose a washer that is not cycling properly. Found lock assembly broken and replaced it. Tested unit and found all is functioning properly at this time. No leaks were found at time of service.

Arrived on site to replace previously ordered parts for refrigerator. Replaced evap fan and light bulb. Tested unit and found all is functioning properly at this time. No leaks were found at time of service.

Arrived on site to test unit for damaged front panel. Found damaged and replaced panel test unit and unit test good job complete.

Arrived on site to test unit for not washing. Test unit and found bad wash motor. Replaced sump and motor test unit and unit test good job complete.

Arrived on site to test unit for no display. Test unit and found and fuse. Replaced fuse at no charge under 1 year warranty test unit and unit test good job complete.

Arrived on site to test unit for door handle hanging. Test unit and found missing screw on right side. Replaced screw and installed new screw to handle test unit and unit test good job complete.

"Arrived on site for washer not completed cycles. Upon arrival confirmed issue and found f7e4 in diagnostics.after inspection of rotor, stator and slider and verified parts integrity I then found cause of failure was control not sending any power to motor. Replaced control and found unit could cycle through all settings in normal operation as designed. Call complete"

"Arrived on site to test unit for not completing cycles, found cam melted. When idler retention bolt removed cam slid right out. Called Techline and was advised engineers working to correct issue but recommend to have customer contact customer service for further details. Was advised unit would be sent for review. No leaks detected. Job complete. SR#7735396404"

"Arrived on site for a washing machine that is not completing cycles. Inspected unit and work area. The customer also stated that beyond the washer not completing cycles, the unit is making screeching sounds when spinning. Ran unit through diagnostics and found an F8 E1 (low/no water detected during fill) error code. Tested both valves and found both valves pulling insufficient water. Filled up the basket a third of the way up the basket and attempted to drain out and did not find any siphoning conditions. Round the unit there an auto test in the unit ran as designed. I did hear the belt slipping on the cam causing the screeching issue. Ordering the cam and belt and will return with the water valve and control. The office will need to contact the customer about a return date due to limited parts availability. ; ordrng 1 W10721967 (Splutch Assembly) and 1 W11239857 (Belt) and 1 W11038689 (Valve assembly) and 1 W11417466 (Control)"

Arrived onsite for F8-E4 error code. Upon arrival unit is beeping with F8-E4 error code. F8-E4 is for open float switch. Inspected switch and found drip pan with water. Ran normal cycle and cannot find leak. Noticed water mark on drip pan from under fill valve. Uploaded pic on SD. Cleared water from pan and cleaned water marks. Water valve may be leaking intermittently. Ordering water fill valve. Office to reschedule ; ordrng 1 W11434044 (Valve)

Arrived on site for chiller flashing error codes and cabinet getting hot again . Customer had unit running hours prior to visit . Cabniet was cool and temp checks normal. Customer had video of error. Reordering control and fan . Call to set return ; ordrng 1 W10782254 (Cond fan) and 1 W10782230 (Fan) and 1 W11296649 (Thermistor)

"Arrived on site to follow up on washer that was making noise and now walking / banging. Found the fluid ring on the basket was separated and sliding. Unit needs a new basket to resolve. Ordering basket. Office to schedule, freight shipped part. ; ordrng 1 W11513243 (Basket)"

"Arrived on site to install parts ordered by previous tech. I tried to pull unit out but I was not able too. They had a custom cabinet built around it and its got nails and screws around the chassis that went though the wood into the metal of cabinet. I was unable to pull unit out, previous tech never pulled it out. Customer will have to reschedule to make the unit available for us to work on it. ; O-emld tckt"

"Arrived onsite for dent in oven door. On inspection found that the oven model # was wrong, corrected the # and order the correct door.; ordrng 1 W11600322 (Oven door) and 2 W11617225 (Screws)s"

Arrived on site for washer not removing water from dispenser drawer. Upon arrival confirmed issue and found all dispenser cups filled with water. Found inlet valve failing and replaced valve/dispenser housing asm. Found cycle on cups on drawer loose and will need office to reschedule once availability of part is known.; ordrng 1 W11400157 (Drawer)

"Arrived on site and inspected washer and found gear case is leaking oil, took pictures. Attempted to remove wash plate and it will not separate. Customer will contact the office if they wish to continue with repair

"Arrived on site and found control panel is unresponsive, replaced it and control board and dishwasher is now working properly and completed a diagnostic cycle, no water leaks detected. Also found drain hose connector to garbage disposal is being shared with a RO system explained why this should not be installed at his way, job complete"

"Arrived onsite for washer not completing cycle and making noise. Upon arrival inspected unit. Put unit in diagnostics and found stored error code F3E2 inlet faulty, f7E9 locked rotor. Tried spinning basket by hand and could hear lower drive components grinding. Inspected underneath unit and found oil leaking from gearcase. Also found worn stator and rotor. Had decided if over a certain amount would replace rather than repair."

Arrived onsite for a range with the oven not heating. I found the oven gas valve coil open and not passing neutral to the ignitor. I replaced the valve and tested the oven. All is working as designed. There were no gas leaks present. Call complete.

"Arrived onsite for previously diagnosed parts. Installed the water inlet valve, tested unit and water is now dispensing. Informed customer that it will take up to 48 hours to get a full ice bin. No water leaks detected

"Arrived on site for no power dishwasher . Found dishwasher dead . Outlet is getting proper voltage . Checked and found wires at terminal block has slipped out of screw . Properly installed power cores ,unit is powering up. Ran diagnostics and no error codes . No water leaks detected. Job complete"

"Arrived on site for washing machine leaking. I I inspected the unit and work area. I found the inlet valve split open from the freeze. I installed the new water valve and ran a diagnostics cycle. I found the unit working as designed. Job complete.

Arrived on site for the fridge not cooling. I inspected the unit and work area. I found the UI not responding or lighting up. I tested voltage to the control and found 120 vac. I tested voltage from the control to the thermistors and found none. The control is shorted and not sending power out. I installed the new control and programmed it. I entered diagnostics and confirmed all components are working.

Arrived onsite for a dishwasher leaking water from underneath it. I found no errors codes stored in the control. I found the float switch drip pan installed upside down and the brass elbow adapter only hand tight at the fill valve causing the leak. I took a pic of both. I tightened the fitting and stopped the leak. I corrected the installation of the drip pan. There were no other water leaks present . Call complete.

"Arrived on site for range, inspected unit and work area. Customers complaint was inner glass shattered. Replaced glass and tested to make sure the oven sensor is reading correctly. Unit is now operating as designed and no leaks where observed . Job completed."

Arrived onsite for a dryer not heating. I found the dryer working as designed. The issue is there was lint blowing out of the back of the dryer because the vent hose came off at the dryer. The vent hose is also ripped where it connects to the house and it is to short to cut off and reconnect.

"Arrived onsite for cooktop burner not staying on when set to,simmer. On inspection the burner would go out when set to simmer. I found debri in the orifice. Clean the orifice out in retested the burner. Now the flame does not go out when set on simmer. Informed the customer how to fix the issue for next time. No gas leaks detected

Arrived onsite for a refrigerator not dispensing ice. I found that foam in the center divider liner had swelled and unclipped the electrical molex connector not allowing voltage to the auger motor. I removed the extra foam and clipped the molex connector in correctly. I tested the auger motor and the unit is dispensing ice properly. There were no water leaks present. Call complete.

"Arrived on site for range, inspected unit and work area. Customer complaint was oven not heating. Tested unit and there was no gas flowing. Pulled unit out and found the oven shut off was set to the off position at the regulator. Flipped the valve to the on and tested. Unit is now operating as designed. No leaks where observed. Job completed."

Arrived on site to test unit for breaker tripping. Test unit and customer had not use the breaker for 4-5 days and the breaker still tripped. Ran unit and unit did not tie breaker advised customer to get to check the breaker. Called Techline and Techline agreed its not the unit tripping the breaker. Sr#7735380189

Arrived on site and replaced previously diagnosed drawer and detergent pump. Unit working as designed. No leaks detected.

"Arrived on site to inspect dryer no power. Upon further inspection, I tested the voltage at the outlet and got 0V. Checked the breaker at the box and found he GFCI breaker tripped. Reset the breaker and tested the unit and it is operating as designed. Customer advised that they were having power outages during the recent freeze. I recommended they contact their builder and advise them of the outages and check/replace the breaker. No lint observed job completed."

"Arrived on site to inspect refrigerator no cool. Upon further inspection, I found dye/refrigerant at the back right corner the unit. Pulled the unit out and found the UV dye drier had leaked. I removed and replaced the dye drier and vacuumed the system. Installed 4.27oz of R134a refrigerant and monitored pressures. Unit held pressures and is cooling. No water leaks observed , job completed."

"Arrived on site to inspect washer leaking water into the tub. Upon further inspection, I found the unit with the water turned off. As soon as I turned the hot water on, water began to flow into the tub. I turned the water off and removed the control panel and found water on the floor and had run down the back panel of the unit. I found the hot valve solenoid had popped off (photo). I removed and replaced the valve and tested. Unit is operating as designed. No water leaks observed, job completed."

"Arrived on site to install previously diagnosed and ordered parts. Due to the main control, gearcase, cam, drive belt and motor failures, I removed and replaced all parts and calibrated the unit. Tested in diagnostics and unit is operating as designed. No water leaks observed, job completed."

"Arrived on site to install previously diagnosed and ordered parts. Due to the filter head leaking and the reservoir frozen, I was to remove and replace both parts. When I removed the filter housing, I found both water lines were cracked. I placed the reservoir in s hot water and was able to get the ice out. I removed and replaced both water lines and the filter housing and tested the unit. Unit is operating as designed. No water leaks observed , job completed."

"Arrived on site to diagnose refrigerator that had flashing lights, and is not dispensing water or ice. Found the pantry co was unresponsive. Found deli control shorted, and a broken wire in the deli harness. Repaired broken wire and replaced deli control. Advised customer that if wiring repair does not hold, we can replace the harness.

"Arrived on site to install previously diagnosed parts to resolve frozen over refrigerator evaporator. Installed new fan scroll, UI and freezer top light. Tested unit and verified all working as designed.

"KRMF706ESS01 Arrived to inspect unit after defrost. I found all functions of the machine returned to normal after the customer defrosted for 48 hours. There was no remnant ice within the evaporator and all functions were present. Operational test good, no leaks observed

"Arrived onsite to install previously diagnosed parts. Upon arrival I installed new control and drain pump. Upon testing I found that the drain new pump would not come on. Upon further testing with My multimeter I found that the harness when bad. Too much resistance. I installed new harness with control and pump.. and tested unit and found unit operating as designed job complete. No leaks"

Arrived on site to replace previously ordered parts for oven. Found new control not the right one for this model. Repaired soldering on original control and tested unit. All is working properly at this time. Advised customer only 90 day warranty on control repair

"Arrived on site to install previously diagnosed parts. Upon arrival I installed new switch and found that the door Message did not go away, Upon further inspection, found that the 20 amp and the bus fuse where both blown, they were not on the first visit. I installed new fuses and tested unit and found unit operating as designed. Job complete"

"Arrived on site to install previously diagnosed and ordered parts. Due to the ice maker, dual valve failures and the ice maker divider being damaged, I removed and replaced the dual valve and divider. I found the ice maker operating as designed as the ice bin was completely full. Also removed and replaced the RC module due to it beginning to fail. Tested the unit and it is operating as designed.No water leaks observed, job completed."

Arrived onsite for not draining and found unit drain pump obstructed by a wire tie. Removed obstruction and unit is now operating as designed.

"Arrived on site for fridge not cooling properly. I spoke to the customer and found out he power cycled the unit and found it working properly afterwards. I entered diagnostics and found no fault codes. I tested the thermistor from the UI and found the, all in range and reading properly. I tested the defrost heater and found it working. I found the gaskets in good condition. I advised the customer that the unit is working properly, and offered suggestion on what areas to leave some space in for better air flow in the unit. The customer paid the diagnostics fee with credit card.

Arrived on site to install previous diagnose part. I installed the new switch membrane. I cleaned the glass and display on the UI. I reassembled the unit and tested it. It is now working as designed.

Arrived on site to install previously diagnosed parts. Inspected unit and work area. Replaced the main control and round the unit up to a 350? cycle bake. Found everything turning on an operating as designed. Call complete.

Arrived on site for a washer that is leaking. Inspected unit and work area. My customer advised of the unit which water all over their floor when they were washing some bedding material and had cause the sink next to it to fill up with water as well. Ran the unit through an auto test and found the unit working as designed until it got to the drain portion of the cycle. Found that the standpipe at the wall was backing up and overflowing leaking water onto the floor and causing the sink next to the washer to fill up with water as well. Did explain to the customer that the issue is not with the washer but with their drain pipe being clogged. Advised the customer that they will need to fix their draining issue for full resolution. Call complete.

"Arrived on site for a dryer that is not turning on. Inspected unit and work area. Check voltage at the terminal block and found 36.7 V from line 1 to neutral, 120 V from line to the neutral and 90.1 V going from line 1 to line 2. Went to check voltage at the plug and found the unit turn on. Found arcing going on inside of the plug potentially causing the issue. The customer also explained that the timer was not advancing prior to the no power issue. Did verify the timer would not advance when I was able to get the unit to start. Found the timer itself was bad. Replaced the timer and tested the unit. The unit began to work and operate as designed. Call complete."

Arrived on site for dishwasher leaking. I inspected the unit and work area. The customer showed me a video of the unit leaking out the door. Inspected the interior of the door and found water splashing out. I inspected the bottom door seal and found it in good condition. I inspected the lower spray arm and found it split spray water where its not supposed to. I installed the new spray arm. I tested the unit and found everything cycling properly.

"Arrived onsite for broken agitator. Upon arrival inspected unit and found agitator tube is fractured and separated from base of agitator. Need to replace agitator.Removed agitator and installed new agitator. Ran diagnostics and there are no saved error codes. No leaks present at this time. Job complete.

Arrived on site to test unit for no power test unit and found correct voltage. Will need new control and console.

"Arrived on site ,replaced gearcase ,clutch , stator ,slider , wash plate . Ran load calibration and test wash all checked normal. No water leaks detected . Job complete."

"Arrived on site and inspected dishwasher and found there is no power showing on display. How are is good at terminal block removed front panel to inspect control board

"Arrived to inspect no power. I found the foam block above the upper cooling fan appeared to be incorrectly placed during manufacture and after time, it fell and was drawn into the blower, stopping upper blower rotation and subsequent cooling. I found the thermal fuse open and after removing and replacing, the unit would not power up. I verified both L1 and L2 to the expected contact points and did find 32.6 and 12.7 VDC at the connector for the UIs VFD at points 1-7 and 1-8, respectively. None of the MFG documentation listed the voltages for the UI and I elected to contact the technical assistance line, MFG tech Steve,SR#7735385509. I advised the of the initial findings and that there were no low VDC voltages published, required to diagnose the no power issue as being the main control or the UI. The tech contacted engineering and they could not provide the required documentation. The MFG tech recommended replacing the user interface and the main control. Due to the voltages found, I suspected the UI to be the issue. The customer is going to discuss with family members and may contact the MFG due to fears of other issues, and will contact us if they elect to have us instal the UI.

Arrived on site to reinstall oven door. Found tabs were not locked into the door. I was able to reset them and get the door reinstalled. Door did not have to be disassembled. Call complete.

"Arrived on site , replaced suspension gearcase ,slider , clutch . Ran diagnostics all checked normal. No water leaks detected at time. Job complete"

"Arrived on site to diagnose refrigerator not making ice. Cycled icemaker and found it cycles, but never calls for water. Tried to jump the terminal to run the valve, and icemaker shorted / shot sparks. Unit needs a new Icemaker and Valve due to short. Replaced icemaker and Valve. Cycled unit and verified all working as designed.

"Arrived on site for washer, inspected unit and work area. Customers complaint was over the freeze the washer started to leak. Tested unit and found no leaks anywhere. I explained to customer its possible the drain line was frozen and when the machine tried to drain it back up and overflowed. Unit is now operating as designed and no leaks where observed. Job completed."

"Arrived on site for refrigerator, inspected unit and work area. Customers complaint was during the freeze unit started leaking. Inspected unit and found the main valve busted. Customer also informed me that the unit has been leaking water inside for a while. Inspected and found the RC drain tube clogged.

"Arrived on site for refrigerator, inspected unit and work area. Customer complaint was icemaker stayed in the twisted position. Tested unit in diagnostics and found that the ice maker was not responding. Inspected the wiring in the door hinge and found 5 broken wires. repair wiring by soldering wires no leaks where observed. Job completed."

"WRV986FDEM01 Arrived to inspect no cool. I found the unit was not cooling and tapping the system revealed 4 of vacuum after the system was balanced and 19 of vacuum with 71 psi while running and after settling for 10 minutes. I exposed both evaporators and found no signs of leaks or dye. The back of the unit had evidence of a cabinet cold spot two inches below the control board cover, at the right lower corner. The appearance of the evaporated condensate was more recent in appearance and the cabinet was not corroded, but the amount of internal cabinet cooling must have been substantial due to the size of the affected area and amount of condensate that had ran down the back of the unit and onto the lower unit cover. I contacted the MFG tech line and spoke with tech Andrew. I advised of my findings and was given file #7735380595 The tech agreed with my findings, but due to MFG constraints, had to require pressure testing. I isolated the suspected affected section and found no issue at 140 psi. I elected to isolate the Yoder and found a leak and contacted the MFG a second time. I spoke with tech Adrian and advised the yoder isolation showed 6 psi of drop in 5 minutes. The unit has been submitted for review and the customer will be contacted for further instructions. No leaks observed

"Arrived on site for microwave, inspected unit and work area. Customers complaint was no heating. Tested unit and it was snot heating. Pulled unit out from cabinet and found that the was plug was directly in the middle of the cavity and when the unit was installed is bending the plug and causing it not to have the correct voltage when in use for mag to activate. Advised customer to move outlet and run the plug t it. Unit is operating as designed at this time. Job completed."

Arrived on site to diagnose a dishwasher that has unusual odor. Found loose connection at pump causing damage to wiring. Repaired wiring and tested unit. Found all is functioning properly at this time and no leaks were found

Arrived on site to replace previously ordered parts for washer. Replaced cam and control and tested unit. Found all is functioning properly at this time and no leaks were found

Arrived on site to replace previously ordered parts for washer. Replaced clutch and slider and tested unit. Found all is functioning properly at this time and no leaks were found

Arrived on site to diagnose a refrigerator that is not dispensing ice. Found wiring at fc hinge broken and repaired wiring. Tested unit and found all is functioning properly at this time. No leaks were found

"Arrived onsite and found unit not drying because it could not exhaust due to slinky duct which had filled with water blocking all airflow. Removed water, determined that the the dryer would exhaust that far after water removed, advised that the unit should have the duct cleaned by building maintenance to repeat poor airflow symptom. Advised on findings and repair."

Arrived onsite for no cool complaint and found refrigerator operating as designed . Customer had experienced soft ice cream and thawing food at one time and hi freezer temp. Advised customer that if pattern occurs control may be shorting.

Arrived on site and inspected washer found drain pump catch is Full of pocket debris after clearing. Washer will complete by diagnostic cycle. Customer says clothes are hot when cycle completes and found waterlines are swapped. After collecting ran a quick wash cycle and it completed properly. Job complete

"Arrived on site and replaced control panel diagnosed by previous technician, job complete"

"Arrived on site and inspected refrigerator and found no ice production, found water fill tube is frozen, took one picture. Used steamer to clear ice and then cycled icemaker oh and its cycle properly and Filled with water, job complete"