Arrived on site to install 3 way valve. Recovered refrigerant and De-braced old valve and braced new valve. I then vacuumed the system and charged it with 5.75 oz of R134. Unit should be working ass designed after this repair. Job completed.

"Arrived onsite for F8-E4 . Upon arrival,power to unit is off. Customer restored power and F8-E4 error code for open float switch automatically appears. Removed kick plate to access drip pan. Drip pan is full of water. Found a drip of water coming from supply hose to valve. Removed hose for inspection. Found rubber washer is good just out of position. Reinstalled rubber washer and reconnected hose. Test unit and no longer leaking. Job complete."

"Arrived on site for refrigerator, inspected unit and work area. Installed all parts ordered previously. Tested and its operating as designed. No leaks where observed during service. Job completed."

"Arrived onsite for a cooktop that would continue to klick when lit. Upon inspection I found that This issue was Intermittent I begin with replacing the Spark module, but found that there was no change. I replaced the harness and tested unit one last time I found that clicking went away job complete."

"Arrived on site for dishwasher, inspected unit and work area. Customer complaint was dishwasher not working. Found a bad pump with error codes 9-1, 10-2. Replaced pump and tested. Unit is now operating as designed. No leaks where observed during service. Job completed."

Arrived onsite for a MW that is malfunctioning the display was not functioning. But all other functions worked. I am ordering the control and the display.; ordrng 1 W11467778 (CNTRL-ELEC) and 1 W11194422 (CNTRL-ELEC)

"Arrived on site to inspect refrigerator no cool. Upon further inspection, I found the unit plugged in and the FC evap fan on. I checked the FC section and found it warm and the evap fan circulating air. I pulled the unit out and checked the compressor and found it not on and neither is the condenser fan. I placed the unit in diagnostics and tested the compressor and condenser fan and when I turned the compressor and condenser fan on I could hear a relay popping on the hv control. Also, I found digits missing on the User Interface (UI). I found at the P1, the compressor and condenser fan is not getting voltage. I am ordering the HV control, UI and will return with the condenser fan motor. Scheduled return service for 02/08/23. Unit left unplugged for safety and no water leaks observed during service.; ordrng 1 W10854027 (Hv control) and 1 W10852669 (UI)"

Arrived on site for refrigerator making noise on inspection found the evap fan was hitting the fan shroud. The bearings on the fan motor our out and the shaft is making the fan blade hit the shroud. Ordering the motor and will replace lights on return.; ordrng 1 W11127829 (Evap fan motor)

Arrive onsite for a refrigerator that is not cooling. Upon inspection I found that the compressor was not running I used a known good start device to test and found that the unit began running and a frost pattern formed. I did find that the door gasket was torn; ordrng 1 W11378944 (GASKET-FIP)

Arrived on site for no cool. Powered unit on loud odd noise from compressor diagnosed a defective compressor ordering a new compressor; ordrng 1 W11547313 (Compressor) and 1 Wpw10143759 (Drier uv) and 1 W11506635 (Access valve) and 1 R600kit (R600kit)

"Arrived on site and found oven is not showing any power. Found thermal fuse has failed. Used a jumper and confirmed oven will work properly once fuse has been replaced. ordrng 1 WPW10545255 (Fuse)"

"Arrived on site for not dispensing ice. Tested ice dispenser ice door motor powered on auger motor not running,checked harness at auger motor no power diagnosed a defective Niagara control ordering new control. ordrng 1 WPW10200659 (Main control), used 1 WP2318054 (Niagara control) from stock"

Arrived on site for center burner not igniting and some of the knobs being broken. I found several of the valves on the manifold are seized and wont open. I replaced the center burner assembly. Because of the valves being seized the manifold needs to be replaced. I am ordering the manifold and authorization. The office will reschedule when we have eta on the part and AUTHO.; ordrng 1 WPW10204705 (Manifold) and 1 Autho (Autho)

Arrived on site for refrigerator with broken gasket. Upon arrival confirmed issue and found rc right side gasket tearing and had exposed magnet strip falling out of place. Replaced and shaped new gasket to door. Found unit sealing as designed. Call complete ; ordrng 1 Cnote (Used 1 gasket)

Arrived on site to possibly install previous diagnose part. I found the correct part not ordered. I am ordering a new filter. The office will reschedule when we have eta on the part.; ordrng 1 W10754439 (Filter)

Arrived on site to diagnose an oven that is not turning on. Found thermal fuse open preventing unit from operating. T-fuse will need to be replaced to complete repairs and office to set return appointment.; ordrng 1 WPW10545255 (Thermal Fuse)

"Arrived on site to inspect dishwasher issues. Upon further inspection, the customer had questions regarding the dispenser. They advised that they dont know if its dispensing rinse aid or not because they cant see the rinse aid in the eyelet. I found they are using a clear colored rinse aid and I recommended they use a blue colored rinse aid. Also, I found the dial is broken and the dispenser is, more than likely, disposing too much rinse aid during each wash. I am ordering the dispenser and scheduled return service for 02/13/23. I made recommendations for use and care and detergent and rinse aid use. No water leaks observed during service.; ordrng 1 WPW10671905 (Dispenser)"

"Arrived onsite fo oven not heating. On inspection found the ignitor was open, went to replace the ignitor and the new one was damaged. No gas leaks detected during service.; ordrng 1 W11176454 (Ignitor) and 1 98005659 (Screw for ignitor)"

"Arrived on site for a stand up freezer that is not cool and Hasnt been cooling since they Bought it. Upon inspection I found the evap fan running but there was no frost pattern. Upon further inspection I found that the compressor was running and pulling 00.31amps. I am ordering a ss r600. Compressor, access valve,up drier. Office to reschedule ; ordrng 1 W11547313 (COMPRESSOR) and 1 Accessvalve (Access valve) and 1 Uvdrier (Uv drier)"

"Arrived on site to test unit for lights not working, tested unit found RC LED module very dim, all other led lights look good, ordering RC led module and control, office to reschedule ; ordrng 1 W11043011 (LED module) and 1 W11043763 (Control)"

Arrived onsite for foam coming out of refrigerator door. Upon arrival inspected unit and found foam insulation seeped through right top corner of RC door. Need to replace replace door. Ordering RC door and name plate. Office to reschedule.; ordrng 1 LW10912110 (RC stainless door) and 1 W11223753 (Badge)

Arrived onsite for not agitating. Upon arrival ran diagnostics and and there are no error codes. Ran a quick overview test and agitation and spin did not operate. Ran a normal cycle and unit fill but intermittently does not agitate. Need to replace control. Ordering control. Office to reschedule ; ordrng 1 W11411581 (Control)

"Arrived on site for no,ice. Ran diagnostics icemaker passed harvest ran fill no water entering icemaker valve energized removed fill line from coupling unable to blow through line diagnosed frozen water line due to a defective fill tube heater ordering a new freezer door.; ordrng 1 LW11026425 (Freezer door ss)"

"Arrived on site for no ice and water dripping from ice container. Ran diagnostics ice box fan not running,E5 errror code on icemaker freezer cooling correctly,power cycled unit ran fast ice fan would power on diagnosed unit will need a new main control and icemaker. ; ordrng 1 WPW10675033 (Control) and 1 W11579560 (Icemaker)"

Arrived on site to test unit for unit leaking and kit advancing. Test unit and found unit leaking from heating element getting wash motor wet and shorting out board. Will need to order new element and control board. Office to reschedule. Unit is in a tight area will order 2 hour job. ; ordrng 1 W11537778 (Heating element) and 1 W11410066 (Control board) and 1 2hourjob (2 hour job)

"Arrived on site to diagnose range with damaged door and left door that shifts slightly while closing. Examined unit and found the right oven door had a protrusion on the right side. Replaced door skin to resolve. Found the new skin was dented in the corner and not an acceptable replacement. Ordered new door skin. I tested the smaller oven door and noticed that when the door gets almost fully closed and seats, it shifts to the left slightly, likely due to how the hinges are angled. Advised customer we can replace the hinges, but based on their design it may not alter the behavior of the door, and it may shift on closing based on the design. Ordering left side hinges. Returning tech can try and swap positions as well. Customer also advised me that the left front burner does not light. Verified that the igniter is sparking, but not lighting. Found service pointer W11643965 applies, to adjust the flame spreader. Ordering a new flame spreader if SP does not resolve. Office to schedule when all parts arrive. ; ordrng 1 W11643896 (Left Small Door Hinge) and 1 W11643900 (Right Small Door Hinge) and 1 W11315557 (Large Door Skin and Glass) and 1 W11319683 (Flame Spreader)"

Arrived on site for refrigerator not cooling. Upon arrival confirmed issue and found temps at room temp in both compartments. Found all fans running but compressor was locking up and turning off. Tried new start device and found same results indicating compressor would need to be replaced. Spoke with sr while on site about part availability and then rescheduled customer for complete repairs ; ordrng 1 W11574734 (Compressor) and 1 WPW10143759 (Uv drier) and 1 W10913906 (Access valve) and 1 R600kit (R600 kit) and 1 Nitrogenkit (Nitrogen kit)

"Arrived on site to diagnose dryer that is not heating. Tested unit and found it is not starting. If you try and engage unit, motor just buzzes. If you hand turn the drum it will start, but will slow and seems to be struggling to turn the drum. Ordering new motor, belt kit and blower wheel to resolve. ; ordrng 1 279827 (Motor) and 1 4392065 (Belt Kit) and 1 WP694089 (Blower Wheel)"

"Arrived on site to inspect washer leaking water.upon further inspection, the customer advised the unit is leaking water from the right side at the back of the unit. I placed the unit in diagnostics showing no error codes. Continued with testing and and when the drain pump came on, I found the drain hose, at the back of the unit, spraying water from the bend at the bottom right corner of the unit (photo). I advised the customer of my findings and am ordering the drain hose. Scheduled return service. Water at the wall was turned off and the unit left unplugged for safety. I had my customer sign the waiver of damages when work with water. ; ordrng 1 W11244231 (Drain hose)"

"Arrived on site for washer, inspected unit and work area. Installed all parts by previous tech and after I was going to run a diagnostics unit would not do anything. I tried resetting by unplugging unit but nothing worked. Unit would not lock so Im ordering the door latch, strike and control if needed. ordrng 1 W11394572 (Latch) and 1 W11457841 (Strike) and 1 W11510463 (Control)"

"Arrived onsite for a refrigerator that is leaking water into the rc. Upon inspection I found that the ice bin was frozen in place I removed the ice and tested the ice door and found that it was leaking air Which can Cause the ice to melt then freeze and I am ordering the ice door the ice box because I found some damage to it, the ice maker. Office to reschedule. ; ordrng 1 WPW10577864 (DOOR-ICE) and 1 W11579560 (ICEMAKER) and 1 W11605504 (BOX-ICE)"

"Arrived on site to test unit for heating issues, the unit found top oven bake glow igniter not working, replaced part, tested unit, unit now functioning as designed, job complete"

"Arrived to instal previously diagnosed and ordered parts. I removed and replaced the front left orifice holder and installed the correct orifices in the rest of the burners. Operational test good, no gas leaks detected during service.

"Arrived onsite for tripping gfci. Upon arrival ran diagnostics and got F8-E3 drain stuck on, F6-E1 low or no water . Resistance of Drain pump is 36 ohms and is within specs. Getting continuous 120 to drain pump with out call for drain. Gfci tripps immediately when drain pump is connected. Need to replace drain pump and control

Arrived on site to investigate previously diagnosed parts. Installed the new Ui and tested the unit to 350?. The UI is worth as designed and the unit is operating as designed.

Arrived on site to installed a new UI and main control. I gained access to the UI and control. I replaced both with new. I powered on the unit and tested both the left and right side oven. I preheated them to 350. I found them both heating as designed.

Arrived on site for dishwasher not starting. I inspected the unit and work area. I ran a diagnostics cycle and found the unit filling with water but not spraying any water. I found the wash motor receiving power but not coming on

"Arrived on site for oven in demo mode. On inspection try following the instructions in the customer care manual and they were not working. I then went to the first step in the manual and thats where I held down the settings button and it went to the tool menu. Went down to info, that is where I found the setting to turn demo off. Showed the customer how to exit demo.

"Arrived on site to inspect refrigerator leaking water. Upon further inspection, the tenant advised water is leaking from the left side of the unit. I disassembled the FC section and found no ice or evidence of frozen water in the bottom of the freezer. I pulled the unit out and inspected the drain tube and removed it and cleared it. I found no ice in the drain and there was water in the evaporator pan from the evaporator defrosting. I checked the ice maker and found no ice or water in the tray. Using my jumper wire, I tested the ice maker from points T-H and it harvested and called for water but no water dispensed. I found the fill tube clogged with ice. Removed the ice and retested and unit is operating as designed. With the ice in the fill tube, when the valve would open and dispense water, the ice blocked the water and the water would back out through the water line at the back of the unit. No water leaks observed at the end of service, job completed. No one available to sign for ticket."

"Arrived on site to inspect refrigerator leaking water from the bottom and puddling in the freezer section. Upon further inspection, I disassembled the FC section and found a slab of ice in the bottom of the freezer and frozen water streaks coming from the right side of the evap drip pan. I removed the evap cover and found a slab of ice in the drip pan and the drain clogged with ice. I pulled the unit out and checked the drain tube at the back of the unit and found it was clear from previous service call and it was the correct P trap type tube. I removed the ice from the drip pan and blew out the drain with my steamer. Using my mirror and flashlight, I placed my flashlight in the drip pan and checked the drain from the back of the unit with my mirror and found the tube is clear now Advised office of agreement. No water leaks observed at the end of service, job completed. No one available to sign for receipt."

Arrived on site to diagnose a dryer that is not heating. Found failed heating element and replaced heater assembly. Tested unit and found all is functioning properly at this time.

Arrived on for a DW that is not filling with water. Upon arrival I put the unit in diag mode and found that the water inlet valve was not letting water in but it would hum. Upon further inspection I found that the valve was clogged. I installed new valve and tested unit and found unit operating as designed. Job completed.

Arrived onsite for a washer that will not turn on. Upon inspection I found that there was no power at the wall to the washer. I reset the breaker and tested for Power to the washer again and found none. I advised the customer that there maybe and issue with this particular circuit and the they are going to have breaker fixed. Job complete

Arrived on site to test unit for lights not working. Replaced bad FC module using S-code S191AQ. Unit now working as designed. No leaks detected. Job complete.

Arrived on site to test unit for periodically not wringing clothes out. Found drain hose was at least 2ft in drain tube. Ran diagnostics and found excessive hose in drain tube was creating a siphon and not draining properly. Referred customer to service pointer W10608624(drain hose installation). Adjusted drain hose for customer and completed diagnostics with no issues. No leaks detected.

"Arrived on site and inspected washer and found cold water valve is leaking. After replacing valve is no longer leaking ran test 51 to confirm operation, job complete

"Arrived on site and inspected washer and found cam inside agitator has worn down and coupler is broken.

Arrived onsite for ice maker overproduction . Upon arrival inspected unit. Found bale arm out of position and not allowing ice maker to recognize the bin is fill. Inserted arm correctly. Shifted arm into off and on position and unit is responding. If symptoms persist recommend replacing ice maker.

"Arrived onsite for built in microwave not powering on. Upon arrival inspected unit. Pulled unit from wall to inspect components and power supply. Inspected incoming supply voltage at block and found unit only receiving 120 vac , however this model is set for 240 vac due to convection cooking potential. Notified builder that unit is not receiving proper voltage. Tested and unit is functioning and heating properly. Job complete"

"Arrived on site to test unit for touch screen not working and loose parts in side door, tested unit found multiple brackets and mounting broken off in side door, when taking door apart door handle mount brackets where also cracked, will need new door to fix issue, job complete"

"Arrived onsite for refrigerator making noise. Upon arrival inspected unit. Ran several tests and found noise was happening when unit is calling for water for ice maker. Bypassed the filter and found noise stopped. Found filter housing needs replacement, internal seals are breaking down. Part W10502642. If customer chooses to move forward he will contact his home warranty for approval and reimbursement. Please contact customer to confirm if moving forward.

Arrived on site for refrigerator not cooling properly. Upon arrival confirmed issue. Couldnt replicate noise reported but was able to narrow down issue to compressor shutting off to early due to over heating/airflow restrictions at condenser coil. Informed customer of findings after I verified both ice bucket was full of ice and evap coil could frost over healthy and evenly. Customer stated they would clean coils themselves. Collected service and found unit working as designed.

"Arrived to instal previously diagnosed and ordered parts. I found the evaporator had ruptured somewhere within the finned area to the right side of the evaporator assy. I removed and replaced the evaporator and elected to replace the compressor due to prior report of it running extremely hot. I vacuumed the system and found no signs of leaks. I charged with the MFG prescribed refrigerant charge and tested. The FC light module would not operate and was causing the ceiling modules in the RC to dim and I found the unit out of serial number range for the MFG TSP. During inspection of the module,I found the wiring defective from manufacture and I contacted the MFG tech line, SR 7735653005 and advised of my findings that the FC LED module was unable to be changed due to incorrect harness routing and excessive insulating foam placement. The MFG tech deemed the issue and that nothing further could be done to correct the lighting system. No leaks observed during service."

Arrived to inspect ignition issues. I found the igniter resistance was 218 and expected was approximately 100 . I removed and replaced the igniter and tested. The unit heated and cycled as designed. No gas leaks detected during service.

"Arrived on site ,replaced evap harness . All checked normal. No water leaks detected at time of service. job complete"

"Arrived on site for dryer shutting off after couple seconds . Found motor centrifuge switch had failed . Replaced motor , unit is functioning properly . Motor is still covered. Job complete"

Arrived on site ge fridge not making ice or dispensing water. I isolated the filter housing and found it not allowing water to pass through. They agreed. I installed the housing and filter. I tested the unit and found it working properly.

"Arrived on site for dishwasher, inspected unit and work area. Customer complaint was dishes not was washing. Entered diagnostics and found error codes 5-1 , 2-1. Found low water pressure coming int the unit. Removed water supply hose and found calcium build up from water heater in the valve. I replaced valve and tested. Unit is now operating as designed. No leaks where observed during service. Job completed.

Arrived on site. Diagnosed a defective freezer led module per service pointer replaced defective led module autho S191AQ ; used 1 W11601310 (Led module) from stock

Arrived on site for light issues. Found a defective led module per service pointer removed all led modules installed updated led modules all leds working as designed. Autho S84638 ; used 4 W11632139 (Led module) from stock

"Arrived on site for no ice. Unit has been running for about 1 day checked icemaker mold ice in mold ran diagnostics no errors ran harvest test ice dumped to bin,power cycled unit ran harvest test passed ran fan test passed ran fill test passed."

Arrived on site to diagnose a microwave that has grease accumulating on cabinets. Found vent system working normally and advised customer on microwave installation and uninstall procedures and that they cannot be perfectly sealed to external venting. No repairs needed and job is complete.

Arrived on site to diagnose a dishwasher that is leaking. Found water leak from incoming water supply hose. Issue is a plumbing issue and builder will need to have supply line replaced to correct issue. Left water off to dishwasher and unit cannot be used until plumbing issue is corrected.

Arrived on site to test unit for gasket coming off on top left corner of RC door. Replaced gasket and formed with heat gun. Unit working as designed. Job complete.

"Arrived onsite for dryer not functioning. Upon arrival inspected unit. Tried running a cycle and unit would engage for 1 second, then quit. Ran diagnostics and found F1E1 error. Per tech sheet, control needed replacement. Replaced control and tested. Unit is now functioning properly. Job complete"

"Arrived on site to install previously diagnosed and ordered parts. Per previous techs diagnosis, I removed and replaced the compressor, access valve, UV dye drier and vacuumed the system. Pressures held and I installed 41g of R600 refrigerant and monitored the unit. Unit began to cool. I placed the unit in diagnostics and tested and unit is operating as designed. No water connections to the unit and no water leaks observed during service, job completed."

"Arrived on site for previously diagnosed parts. Installed gear case,actuator,belt,capacitor and cam . Tested unit in diagnostics mode and the squealing noise was not there. Unit operating as designed and no water leaks detected during service."

Arrived on site for dishwasher that wont latch. On inspection found the latch was sprung upward and the strike could not close into it. It damaged the strike so I replaced both pieces. The unit is operating as designed now. No water leaks were detected during shipment call.

Arrived on site to diagnose a range that is not baking. Found bake ignitor faulty and replaced it. Tested unit and found all is functioning properly at this time.

Arrived onsite to install previously diagnosed parts. Upon arrival I installed new oven boor glass and tested unit and found unit operating as designed. W15P811WPL1 Ref # 7735487430 job complete

"Arrived on site to test unit for element not working, customer stated that FR burner did not work from day one, removed top and found element disconnected, secured connection, tested unit, unit now running as designed, job complete"

"Arrived onsite for all burners starting giving off yelow flame and not adjusting to low burners. Upon arrival test unit and all burners are burning correctly with only blue flame. After series of questions. That customer said that the yellow flames only happened when using a vaporizer machine. I explained how vaporizers, and dehumidifiers can effect air quality and change the flame. Also adjusted each burner so that the low settings operate to customers liking. No leaks present at this time. Job complete"

"Arrived onsite for not washing correctly. Upon arrival customer stated that the unit spins just does not agitate. ran diagnostics and there are no saved error codes. Ran an automatic cycle and hear rubbing noise from agitator and grinding noise from belt area. Inspected unit and found failed hub, actuator is not shifting correctly causing cam to fail. Replaced hub, actuator and cam. Test unit and unit is operating as designed. No leaks present at this time. Job complete"

Arrived on site and found dryer vent hose connector is damaged and lint is blowing out. After resetting it confirmed dryer is working properly and airflow is good. Job complete

Arrived onsite for a wall oven that is no longer operational. Upon arrival I found unit with f6e4. Code. I replace the control but couldnt test unit because the power when out at the home. Customer to call if issues is not resolved. Job complete.

"Arrived on site and inspected refrigerator and found it is not defrosting. Found brown wire to heating element is not in harness connection, took one picture. After resetting wire set refrigerator into a manual defrost through diagnostic cycle and heating element is now heating properly. Customer will manually defrost refrigerator for48 hours after that refrigerator should be working properly, Job complete."

"Arrived on site and found wash motor has failed, after replacing wash motor dishwasher is operating properly. Discussed drying expectations, rinse aid usage and importance of running hot water at kitchen sink before starting dishwasher, job complete"

"Arrived on site and replaced igniter diagnosed on previous visit, after replacement bake cycle is working properly, job complete. took one picture"

Arrived on site . Replaced inner door liner and both hinges . Door is functioning properly. . Job complete

Arrive to install fill valve that is weeping. Installed the fill valve and tested unit no water was seen weeping into the dishwasher. Customer says that it takes a few days for it to fill up the dishwasher. No water leaks detected during service call

Arrived onsite to replace faulty hoses. Replaced hoses hoses and tested. No signs of leaking at this time. Job complete. Please mail customer a receipt. Job complete . Office to complete payment processing.

Arrived onsite for washer not starting a cycle. Upon arrival inspected unit. Found in diagnostics error code for latch failure. Tested latch and latch kept clicking. Replaced latch. Tested unit and unit is functioning properly. Job complete

Arrived onsite for ambient LED lights not functioning. Upon arrival inspected unit. Blower motor and main lights are functioning. Check wiring for light drivers and found issues with voltage. Called tech line for assistance. Tech provided SR#7735645409. Test showed 120 vac from blue to chassis and yellow to chassis but not across blue to yellow. Tech recommended uninstalling and dropping whole unit to inspect for wiring or break in harness. Will need two man due to installation setup. Discussed with SW and CS. Office to reschedule

"Arrived onsite for refrigerator making humming noise. Upon arrival inspected unit. Opened doors to get compressor to kick on. Could hear vibration noise, however noise was intermittent and would stop when moving unit . Accessed compressor compartment and found packing debris jammed. Removed debris and leveled unit. Unit now seems to be operating within normal spec. Customer will monitor. Job complete"

Arrived on site and customer said unit has been working she will call back if unit stops working.

"Arrived on site to test unit for no ice production, tested unit found ice maker was off, turned on ice maker and showed customer how operate it, ran diagnostics cycle, completed cycle and filled with water, unit is running as designed, job complete"

"Arrived on site to replace previously diagnosed infinite switch, replaced switch, tested unit, unit now functioning properly,job complete"

"Arrived on site for washer, inspected unit and work area. Customers complaint was they tried running a load and it was still not working after last tech left. I entered diagnostics and retrieved error codes F9E1, F8E6, F0E3 & F0E5. I erased all error codes and inspected the harness and found no shorts on any part of the lower harness. The connector to the drain pump did not look like it was plugged in properly. I ran the drain pump in diagnostics and inspected harness wile pump was on and never failed. I informed customer that its possible that when the error codes are not erased the unit can think its still not fixed. No leaks where observed during service. Job completed."

"Arrived on site to inspect cooktop center burner flame. Upon further inspection, I tested all burners and all burners except the middle burner are operating as designed. I found the middle burner flame will shut off when switching from simmer low to medium. I adjusted the flame through the valve and retested and unit is operating as designed. I demonstrated for the customer and made recommendations for use and care. No gas leaks detected during service, job completed."

"Arrived on site for range, inspected unit and work area. Customers complaint was oven not working properly. I re-diagnosed unit and found that the igniter was not having a good ground. I replaced igniter and bake burner and tested. Unit is now operating as designed. No leaks where observed during service. Job completed."

"Arrived on site for icemaker problems. Inspected unit and work area. Installed some parts ordered by previous tech. Installed icemaker, icebox fan and icebox. I cleared error codes from the icemaker and retested. Unit is now operating as designed and no leaks where present. Job completed."

"Arrived on site for water leaking during icemaker fill. Found fill tube not inserted into fill cup,removed icemaker installed fill tube correctly into fill cup tested icemaker fill passed with no leaks"

"Arrived on site and replaced previously diagnosed gearcase, rotor, slider, stator, clutch and suspension. Completed diagnostics with no issues. No leaks detected. Job complete."

Arrived on site to test unit for ice and water coming from dispenser when not engaged. Found ice maker is not being used enough causing ice to fuse together and get stuck in chute. Advised customer to periodically empty icemaker to allow fresh batches to be made and prevent ice fusion. Also rerouted water line to dispenser to prevent weeping on face of FC door. No leaks detected. Job complete .

"Arrived on site to test unit for excessive heat on top right side of oven door. Found gasket was opening. Replaced gasket, unit working as designed. Job complete."

"Arrived on site and replaced control board and motor diagnosed on previous visit, washer will now complete a calibration cycle and both agitations and both spins are operating properly. Washer will complete an automatic test cycle, job complete."

"Arrived on site diagnosed a defective led module,per service pointer removed all led modules,installed updated led modules autho S84638; used 2 W11632139 (Led module) from stock"

"Arrived on site for no water or ice. Found frozen water tank diagnosed air leaking between fan scroll and air tower causing tank to freeze,defrosted lines added sealer between gaps tested icemaker passed filled with water tested water dispenser passed. ; used 1 212643 (Sealer) from stock"

Arrived on site and inspected refrigerator and found ice production is good. Customer complaint is that there is frost buildup on bottom of iceman. Disassembled ice dispenser area and found some frost around perimeter Where ice chute connects to freezer door. took multiple pictures and documented with techline. 7735641254

"Arrived on site to inspect range oven not heating. Upon further inspection, I disassembled the oven and tested the oven on bake and found the ignitor not arcing properly. I removed and replaced the ignitor and retested and unit is operating as designed. No gas leaks detected during service, job completed."