"Arrived on site to install previously diagnosed and ordered parts. Due to the RC evap motor failure and the right RC door gasket being torn, I removed and replaced the RC evap,cover with fan motor and right RC door gasket and sealed the drain tube at the back of the unit and tested. Used my heat gun to shape the gasket. Unit is operating as designed.No water leaks observed during service, job completed."

"Arrived onsite for a range that will turn itself off as though you unplugged it. Upon arrival I ran the unit in bake and found that it preheated properly and the cylinder off and the on like normal, I tested the voltage at the wall and found that it was a steady 120vac, the I tried running the unit again and it turned itself off like it was unplugged but it was still plugged in to the wall. I installed the new control/clock and tested unit ss time and found unit operating as designed. Job complete"

"Arrived on site to install previously diagnosed and ordered parts. Due to,the motor failure and the element bushings being incorrect, I removed and replaced the sump/motor assembly and element and tested. Unit is operating as designed with no leaks. No water leaks observed during service, job completed."

Arrived on site to test unit for unit not working no power. Test unit and found switch at wall turned off. Turned switch on test unit and unit test good job complete.

"Arrived on site for fridge leaking and lights . Found drain clogged with a sheet of causing drain to over flow and occasionally causing door not to close properly and cause it fridge to shut off lights . No other issues found .

"Arrived on site for tempmissues and dripping in fresh food . Found evap drip tray solid ice . Evap has normal frost . Removed ice ,drain tube clear and draining . Found heater ohm out at 105.8 . Recommended changing control due to inconsistent defrost times . Reran diagnostics all checked normal. No water leaks detected.

"Arrived on site to install previously ordered parts. Replaced motor, cam, and belt. Test unit and unit is operating as designed. No leaks present at this time. Job complete.

"Arrived onsite for unit not operating. Upon arrival test polarity and is good. Test. Pts switch , fuse, door switch, and motor and are all checking good. Need to replace harness.

Arrived onsite and determined washplate seized and unable to be removed. Advised customer on additional needed part and customer requested keeping the for gearcase at their home in the box. washplate and belt to repair. ; ordrng 1 W10752283 (Washplate)

Arrived onsite for refrigerator not cooling. On inspection unit was in the maintenance building and there was evidence that the evap was frozen. On further inspection found that the thermistor was reading 2.7k 77? the air temperature was 75? the heating element read 23 ohms. When I checked the evap fan motor it was OL. Ordering a new evap motor. ordrng 1 WP2315549k (Evap fan motor)

"Arrived on site for least front burner not sparking and igniting . Igniter is sparking when other knobs are turned . . Ordering valve with switch . ordrng 1 W10475147 (Spark module) and 1 W10371235 (Valve with switch)"

"Arrived on site for fridge making noise . Found freezer fan icing up also found FZ door rails are not closing properly at times and allowing warm air in . No water leaks detected at time of service"

"Arrived on site for refrigerator not working properly, inspected unit and work area. At arrival customer informed that the water dispenser had stopped working. I retrieved the temps in the RC 27? its to cold causing the water to freeze up. Also the customer made me aware that the ice bucket was broken from the previous company who serviced the refrigerator. ordrng 1 W11645127 (Diffuser) and 1 W11244434 (Ice container)"

"Arrived on site to test unit or not shutting off. Customer stated they use timed dry and unit will not shut off even when reached off cycle on timer on all options. Recommend replacing timer, fix thermostat and vent thermostat. Reached safety team outside of operating hours and could not document. Recommend reaching safety team prior to attempting any repairs for approval. ; ordrng 1 WP3977767 (Thermostat) and 1 WP3387134 (THRMST-FIX) and 1 279816 (Thermal fuse)"

"Arrived on site for refrigerator not cooling. Upon arrival confirmed complaint and found compressor screeching extremely loud indicating it was internally locked up found amperage staying over 9 amps even with new replacement start device. Found compressor failing, will need office to reschedule once availability of parts is known W11370574 compressor, W11368877 evap coil, r600 kit, nitrogen kit, WPW10143759 uv drier, access valve W10913906, and lokring kit; ordrng 1 W11370574 (Compressor) and 1 W11368877 (Evap coil) and 1 R600kit (R600kit) and 1 Nitrogenkit (Nitrogen kit) and 1 WPW10143759 (Uv drier) and 1 W10913906 (Access valve) and 1 Lokringkit (Lokring kit)"

Arrived onsite for MW door not closing. On inspection found that the door needs to be pushed in for the unit to turn on. I troubleshot the unit in found the interlock micro switches were bad. Replaced them and the unit would not turn on no matter what. It has power but when you select a time and push start nothing happens. Ordering parts from the conversation I had with Susie.; ordrng 1 W11033422 (Interlock) and 1 W11261167 (Appliance manger)

"Arrived on site to inspect wall oven error codes. Upon further inspection, I placed the unit in diagnostics and checked error codes and found F8E0-cooling fan speed. I tested the cooling fan on high and found the fan motor humming, but the blades failed to operate. I removed the unit from the cabinets and found the back panel badly damaged (photos). Removed the panel and found the fan mount bracket badly damaged as well (photo). Also found the fan housing badly damaged and pushed into the blades keeping them form rotating (photo). I removed and replaced the blower assembly and using my rubber mallet, I was able to semi straighten the back panel and get placed back on the unit. Tested the blower and it is operating as designed but the panel is vibrating. I am ordering the back panel, the mounting bracket & foam, along with CNOTE-LSO PER CUSTOMER REQUEST. Office to schedule return service due to the availability of parts. Unit is operable at this time, but making a vibration noise.; ordrng 1 W10491987 (Foam) and 1 W11166802 (Fan mounting bracket) and 1 W11134657 (Lower back panel) and 1 W11134657CNOTE (LSO PER CUSTOMER REQUEST)"

"Arrived on site for refrigerator not cooling. Upon arrival confirmed complaint and found compressor screeching extremely loud indicating it was internally locked up found amperage staying over 9 amps even with new replacement start device. Found compressor failing, will need office to reschedule once availability of parts is known W11370574 compressor, W11368877 evap coil, r600 kit, nitrogen kit, WPW10143759 uv drier, access valve W10913906, and lokring kit; ordrng 1 W10913906 (Access valve) and 1 WPW10143759 (Uv drier) and 1 Nitrogenkit (Nitrogen kit) and 1 W11370574 (Compressor) and 1 W11368877 (Evap coil) and 1 R600kit (R600kit) and 1 Lokringkit (Lokring kit)"

Arrived on site. Removed mullion found broken wire on mullion harness part that was ordered was incorrect ordering correct part; ordrng 1 W11649966 (Mullion)

Arrived on site for unit not cooling. Upon arrival customer stated that the evaporator cover was covered in ice. Unit is now in garage. Customer left unplugged to melt ice. Restored power to unit and compressor turned on. Removed evaporator to check defrost components. Got a good frost pattern throughout the entire evaporator. Found ui is not lighting up or responding. Did find voltage to ui. Test resistance of heater and is 30 ohms. Need to order ui. Office to reschedule ; ordrng 1 W11518204 (UI)

Arrived on site for refrigerator. Couldnt find unit on site. Will need office to reschedule once unit is found. ; O-emld tckt

"Arrived on site for unit not powering on. Upon customer has back panel of console removed. Customer has screw put away. Test polarity and is good. Not getting voltage from control to UI. Also found water in tub. Customer stated that unit shut off during wash cycle. Ran resistance test on drain pump and is 19 ohms. During inspection of drain pump found some yellow greasy residue on rotor. Cannot determine if unit has a leaking gear case. The drain pump has mechanically failed and need to replace before replacement of control. Need Autho for control, UI, and drain pump. Office to reschedule ; ordrng 1 W11396717 (Drain pump)"

"Arrived on site for loud noise. Diagnosed condenser lines vibrating in compressor compartment,adjusted tubing lines noise no longer present"

"Arrived on site to inspect cooktop burners taking too long to ignite. Upon further inspection, the customer explained that when they would go to turn the front right burner on, it would take a long time to ignite and when it ignited there would be a large flame. I tested all burners and all are operating as designed. With the front right burner, I moved the burner cap to the side of the burner head and demonstrated what happens when trying to light the burner and the customer advised thats what she was seeing. I advised that the burner cap is not seated correctly which causes the ignitor to not arc against the cap like the designed too which in turn allows more gas to escape and once it does ignite, it shoots out a large flame. I made recommendations for use and care. No gas leaks detected during service and no repairs needed at this time, job completed."

"Arrived on site to test unit for thumping noise. Customer stated noise has not been present recently and denied service. No service provided, no fee collected. Job complete."

Arrived on site and charged to specs. Unit took charge properly and no loss in vacuum since last visit. Evap developing frost as designed. Job complete.

"KRFF507HPS04 Arrived to instal previously diagnosed and ordered parts. I applied sound deadening material strategically throughout the lower unit area and after complete, could not recreate the noise during any refrigerator state, compressor running or not. Operational test good, no leaks observed during service."

Arrived onsite to install previously diagnosed parts. Installed ui and spoke with customer about the oven not cooling down. I explained the unit is designed to hold the heat. If it cools down really fast there is a issue. I said if the door it is not open it will hold the heat for hours. The unit is operating as designed.

"Arrived onsite to test unit for not drying clothes properly, customer stated that it take twice as long then before, tested unit with vent tester and found it completely restricted, inspected vent hose and found it blowing up under pressure, advised customer to hire vent cleaners to address this issue, stated to customer not to use unit until restrictions has been removed to prevent potential damage to unit, job complete"

"Arrived on site to test unit for chimney replacement, customer stated that chimney is not centered properly, and damage on the vent hood body, inspected chimney found it is not installed properly by installers, dent in the hood is no longer covered by cosmetic warranty, vent hood has multiple scratches as well, unit has no failed components, and is running as designed, customer stated that he will call contractor to resolve this issue, job complete"

"Arrived on site to test unit for loose console, tested unit did not find anything unusual about the movement, removed cook top, inspected console towers, all screws are in place and movement is within manufacture specifications, unit is functioning as designed, job completed"

"Arrived on site to test unit for not washing properly, tested unit found drain pump not receiving voltage, around, continuity through harness, and found a broken wire, fixed wire with butt splice, tested unit is now running as designed, if issue persist a new lower harness will be needed job complete"

Arrived on site to test unit for not starting. Found tub was full of water. Found drain pump had connection broken off preventing from draining. Verified receiving proper voltage. Installed spade connection and drained out water. Ran diagnostics with no issues. Advised customer on load sizes to prevent unit from bottoming out and causing damage to pump. No leaks detected. Job complete.

"Arrived on site and replaced previously diagnosed gearcase, slider and suspension. Was able to remove wash plate this time out. Ran calibration and completed diagnostics with no issues. No leaks detected. Job complete."

"Arrived on site to test unit for no ice production, tested unit found bin full of ice, ran diagnostics cycle and it passed, customer stated that she had issues with her water lines and once that was fixed ice production started, unit is running as designed, no leaks detected job complete"

Arrived on site. Replaced both damaged doors and nameplate. Job complete

Arrived on site to replace regulator. Replaced regulator test unit no leaks present job complete.

Arrived on site to test unit for door not closing. Test unit and found and hinges. Replaced hinges test unit and unit test good job complete.

"WTW4855HW3 Arrived to inspect noise complaint. I found the bolt for the cam assy had came off and I removed and replaced the cam assembly due to excessive wear from the bolt issue. I recalibrated and then tested within service test mode. Operational test good, no leaks observed during service."

"WED4985EW0 Arrived to inspect drying issue and excessive lint. The tenant expressed concerns about the amount of lint ejected from the external vent to the apartment unit. Initial testing was the timed heating/cooling to prove airflow and I found the unit would not heat above 165?F. I checked the electrical supply and it was L1 122.3VAC L2 121.4 and L1-L2 211.8, the combined expected as the complex is on a 3-phase supply. Under load, the 211.8 declined to 208.9 and is sufficient. I found no heater circuit shorts to chassis and reran the test, viewing the element. There was very little element that heated to glow, only at the very top of the element. 19.9 amps were measured at L2 and no heat, L1 was 6.2 amps. With heat, L1 registered 25.6 amps. The motor made a very loud vibration and I elected to replace it and the blower. The door switch was intermittently failing and I removed and replaced. Testing after service showed the unit still heating slowly, but I attribute that to very good airflow. I advised the tenant of my findings."

"KRMF706ESS05 Arrived to inspect noise. I was able to somewhat recreate the noise the customer heard, but at a lower intensity. The sound heard was vibration within the lower unit area and started at the condenser entry loop. I secured the loop and added sound deadening material to the general area. I found the drain tube assembly gapped and I corrected. I squared and leveled the chassis and found the left door hinge, badly bent downward, preventing proper fitment with the ice bin to fascia contact area. I removed the door and corrected the hinge issue and tested. The unit operated as designed, no leaks observed during service."

"Arrived on site for washer, inspected unit and work area. Customers complaint was stoped while washing bath rugs. Inspected and found water in tub. Used my jumper harness to activate water pump and drain water. Found that the harness on the water pump broke. I did a successful repair on the harness and tested. Unit is now operating as designed. Job completed."

"Arrived on site for microwave, inspected unit and work area. Customers complaint is that the food is catching on fire and styrofoam plates melting. I tested unit and found it operating as designed. Advised the customer to no use styrofoam in microwave. Job completed."

Arrived onsite and replaced heater under service pointer #w11540694 guidance. Unit is now operating as designed. Unit had not developed leak failure prior to repair.

"Arrived onsite for dishwasher not working. On inspection found that there was a error of F4E3. I found that the strainer in the dishwasher was clogged. Explained to them that the strainer needs to be clean at least once a month. Ran diagnostics cycle 3 times trying to Get the unit to fail, the motor never got hot. The spray from the arms was very significant. Information the customer that if it happens again lets know"

"Arrived onsite on refrigerator making a noise. On inspection the compressor was vibrating and make a noise, I secured the compressor to keep from vibrating and the noise quiet down, you can hardly hear the noise any minute. No water leaks detected during service."

"Arrived on site to inspect range oven door not closing. Upon further inspection, I tested the unit and found the door hinge drops when closing the oven door. I removed and replaced both hinges and retested and unit is operating as designed. No gas leaks detected during service, job completed. No one available to sign for receipt. New build/vacant home"

Arriving onsite for a cooktop with the rear deft burner not working. Upon inspection I found that the burner was shorted out. I replace it and tested the unit several times and found unit operating as designed.

"arrived on site for no ice. Ran diagnostics shorted evap sensor,unit passed all diagnostic test,good water flow filled pan,recirculating pump working good frost formation on evaporator plate. Replaced evaporator sensor."

Arrived on site to test unit for unit moving not secured to counter. Customer had the brackets but we dont have long enough screws. Advised customer to get installers back out to install the unit correctly. Job complete.

Arrived on site to test unit for unit not washing. Test unit and found bad sump and motor. Replaced sump and motor test unit and unit test good job complete.

"3276Arrived on site for ice build up in freezer section,opened fresh food doors found middle of door gasket not sealing to cabinet,removed sealer that was placed under gasket,found gears not aligned. Realigned gears raised freezer door checked seal good,heated gasket,door gasket sealing correctly to cabinet. Hold on to freezer door incase customer calls back"

"Arrived onsite for a refrigerator that is making growling/vibrating noise whe the compressor kicks on. Upon inspection I found that the noise was coming from the condenser making count with the chassis causing resonating vibration to solve this issue. I adjusted the chassis till the noise when I moved on to the ice clumping in the husband and found that the ice was clumping at the top, which is a sign that ice bin gasket at the top may not be sealing properly. I checked this and found that it was not I meant, and I made adjustments to the gasket as well. Make sure that it was not folding when the door closed now it is sealing much better. Unit is now operating as designed job complete"

Arrived on site for refrigerator. Upon arrival found unit out of warranty. Customer wants to contact whirlpool for further assistance. No service preformed.

Arrived on site for stove indicator light remains on. Upon arrival inspected unit and found that the right front infinity switch has failed. Need to replace front right infinity switch. Replaced 1 switch WP3149400. Test unit and unit is operating as designed. Job complete

Arrived on site for dryer taking long time in between loads to be used . Conrtol will die and flash 6-1 error . Ran diagnostics only ui error present . Replaced UI and unit is functioning properly. No gas leaks detected at this time. Job complete

"Arrived on site for cooktop, inspected unit and work area. Customers complaint was unit not igniting. Tested unit and found the cooktop unplugged. Unit is now operating as designed. No leaks where observed during service. Job completed."

"Arrived on site for vent hood, inspected unit and work area. Customers complaint was the light was not working. Tested and found the light bulb lose. Unit is now operating as designed. Job completed."

Arrived on site for dryer making loud noises. Inspected unit and work area. I confirmed the noises and found it was the motor bearings going out along with the wheels getting stuck. Replaced all parts needed and re-tested. Unit is now operating as designed. No leaks where observed during service. Job completed.

"Arrived on site for water leaking and bowed drain pan. Per service pointer replaced drain pan,secured thermistor to correct location on suction line,secured evaporator to liner using clamps and zip ties secured cover. Autho S16360; used 1 W11457241 (Drain pan) from stock"

"A arrived on site for range, inspected unit and work area. Customers complaint was unit not able to cancel the oven. Confirmed and fount the control not responding to the cancel button. Contacted the safety team from whirlpool and spoke to Eric SR#7736123395 and explained my findings. Replaced the control and tested. Unit is now operating as designed. No leaks where observed during service."

"Arrived on site to test unit for leak. Found drai hose leaking. Replaced hoses, unit working as designed. Job complete."

Arrived on site for unit not cooling. Upon arrival found lots of frozen condensation in FC. Found about 8 of gasket on bottom of RC door is not sealing. Found door is not securely mounted. Adjusted and secured the door. Gasket now seals correctly. Cleared all frost. Unit is operating as designed. Job complete

Arrived on site for blower not blowing . Found piece of sheet rock stuck in fan blades . Removed debris. Fan is operating properly. Job complete

Arrived on site for refrigerator not cooling. Upon arrival confirmed issue. Found cause of failure was cap tube breaking from drier. Replaced uv drier WPW10143759 and 6-2 coupler from lokring kit. Pulled vac then recharged system with 41g of r600. Found unit cooling as designed. Call complete

Arrived on site for dryer needing previously diagnosed blower wheel. Upon arrival reconfirmed issue and found blower would not safely come free from motor. Replaced motor and blower wheel and found unit working as designed. Call complete

Arrived on site for washer powering up and filling but not starting . Ran diagnostics got 7-1 error . Found nut had come off cam pulley and cased belt to slip off pulleys. Replaced cam with truck stock ( w10721967 ) . Ran calibration and diagnostics wash . All checked normal. No water leaks detected at this time. Job complete .

"Arrived on site for refrigerator with high side leak. Upon arrival reconfirmed leak. Replaced compressor, uv drier, and access valve. Pulled pulled vac and used nitrogen to verify there were no leaks. Found not could hold 130psi. Recharged system with 5.5oz of r134a and found psi stable at 0/150(L/H) after 25 minutes. Informed customer to give unit 24 hrs to stabilize temps. Call complete"

"Arrived to perform Heater Bushing W11537778?- SP W11540964 - Special Project S17304. I removed and replaced the copper colored bushing equipped heating element and then entered service test mode. Errors F8E2, F10E1 and F10E2 were stored and I cleared for testing. The unit passed all testing and I suspect the codes were from installation and they did not return. All testing was done in accordance with the SP W11540964. No leaks observed during service."

"Arrived onsite for dishwasher not draining. On inspection the new pump and motor had a bad drain pump on the unit. Replaced the drain pump,and the unit started to drain. The unit is well as designed and no water was detected during inspection."

Arrived onsite to install previously diagnosed parts. Upon arrival I installed new water feed line and tested unit and found unit operating as designed. Job completed

Arrived onsite to install previously diagnosed parts. Upon arrival I installed the new damper and tested unit and found unit operating as designed.

Arrived onsite for a ran that has a left door on the oven the wiggles when it closes. Upon inspection I found that this was caused by the left hing on the left door beeping weak. I replaced bothering hinges and tested the unit and found the door opening as designed.

"Arrived onsite for a ice machine that is no longer making ice and was making a crunching noise. Upon inspection I found that the water inlet valve was not operating correctly and the noise was coming form the circulation pump cavitated because there was not enough water reservoir. After installing the new water inlet valve, I found that the noise was gone and that the unit created a nice slab of ice after monitoring it for several minutes job complete."

Arrived onsite and tested unit for not closing properly. Determined unit installed well and when door is closed properly the the switches stay engaged properly. Customer experiencing reverberation from slamming the door disengaging one or both switches. Advised customer on design and the advantages of gentle closure to engage the switches both for consistent responsiveness and wear reduction. All checks good. Unit is operating as designed.

Arrived on site for oven too cold. Upon arrival customer stated that an inspector checked unit and that they were getting readings too cold. I preheated oven to 350 and used thermocouple to test readings. Oven reached 460. Began to let unit cycle several times and got 328 on the low and 380 on the high averaging 354. Unit is operating correctly as designed. No gas leaks present at this time.

Arrived on site for not spinning. Upon arrival ran diagnostics and got F7-E6 motor circuit open. Inspected motor and is good. Found actuator and cam have failed. Need to replace actuator and cam. Replaced actuator and cam. Test unit and unit is operating as designed. No leaks present at this time. Job complete

"Arrived on site to preform previously diagnosed sealed system, verified that it was needed, replaced compressor, dye drier and stub, vacuumed system down for 30 minutes, held good vacuum, charged system with R600 56g, unit developed a good frost pattern, advised customer to give unit 24 hours before loading, no leaks detected job complete"

Arrived on site to replace sump and motor. Replaced sump and motor test unit and unit test good job complete.

Arrived on site to test unit for not draining. Test unit and found slow drain due to disposal back filling. Cleared disposal test unit and unit test good job complete.

Arrived on site for washer leaking . Checked and found nothing wrong with bellow . Ran diagnostics only oversuds error . Ran diagnostics manual and auto test with top off . No water leaks detected. Drain stand is normal. Did find some water coming from dispenser . Replaced draw . Reran auto test . No leaks detected at this time. Job complete

Arrived on site for left side control panel wobbly . Tightened down bracket screws . No other issues found . No gas leaks detected at this time . Job complete

Arrived on site to test unit for F1E0 interior control. Replaced control test unit and unit test good job complete.

Arrived on site to replace turn table motor. Replaced motor test unit and found unit making noise from vibration. Took unit down and no noise job complete.

Arrived on site to test unit for oven not getting to temp. Test unit and found unit at average temp to be correct. Showed customer how to calibrate the oven job complete.

Arrived on site to test unit for F8E0. Replaced upper cooling fan test unit and unit test good job complete.

Arrived on site to test unit for unit not dissolving soap. Test unit and found unit not getting any water. Opened water valve under sink test unit and unit test good job complete.

Arrived on site to replace tub gasket. Replaced gasket test unit and unit test good job complete. No leaks present at this time.

Arrived onsite for complaint of shutting off after 30 seconds of use and having to be unplugged and replaced in to restore function. Tested unit and unable to replicate any symptoms. Cooling fan running properly and control operating as designed. Advised that in event of ongoing failure control and filter board will be ordered.

Arrived onsite for refrigerator not functioning properly. Upon arrival customer declined service. Did use prescreened control to service another unit in 304. Job complete

Arrived onsite for door alignment concern. Found door had not had cabinet face yet installed. Made manual adjustment to door alignment to correct. Unit is now aligned and operating properly. advised Customer on repair. All checks good.

Arrived onsite for refrigerator not cooling properly. Upon arrival inspected unit. Found frost buildup on evaporator cover. Ran diagnostics and forced defrost. Unit did energize. Replaced control. Control was marked with double sticker. Advised customer manually defrost unit then restart. Is symptoms persist recommend ordering defrost thermistor and UI. Job complete

Arrived onsite for washer hitting the walls. Upon arrival inspected unit. Ran diagnostics and found no stored error codes. Ran test cycle and all complete as normal. Spoke to customer and found that unit may have been loaded off balance. Tested all components and unit is functioning as designed. Instructed customer on proper loading. Job com.

"Arrived on site and Customer is experiencing dryer gets noisy after running for at least 8 to 10 minutes. found dryer is heating properly but found airflow is showing Blocked/clogged/restricted. Took one picture. Dryer is overheating which is causing it to rattle. With vent hose off observed dryer run for 10 minutes quietly. Recommend it to homeowner that vent to the exterior of the home be cleaned/cleared by a service, dryer should not be used until this has been done properly, job complete"

"Arrived onsite to replace faulty compressor. Unit R134a. Replaced compressor, dye dryer and access valve. Pulled vacuum and held. Charged per spect and powered unit. Unit is functioning properly. Job complete"

"Arrived on site I am found dishwasher drain pump is running dry and its noisy. Allowed cycle to start and dishwasher is working properly. Now that there is water in it drain pump is running normally/quietly, job complete"

"Arrived on site for loud noise. Found evaporator fan cover not installed correctly from manufacture,installed cover correct.y noise no longer present"

"Arrived on site to install previously diagnosed and ordered part. Due to the cooktop being damaged, I removed and replaced the cooktop and transferred the bezels from the old cooktop to the new and tested. Unit is operating as designed. Job completed."

"Arrived on site to install previously diagnosed parts. Upon arrival I installed the new slider, rotor and stator. And tested unit and found unit operating as designed. Job complete"

Arrived onsite to install previously diagnosed parts. Upon arrival I installed the key pad and control. And the unit regained functionality. I then ran a temp test at 350* and found unit operating as designed. I also adjusted customer to allow make sure that the oven door is shut firmly when in use