"Arrived onsite for dishwasher not working. On inspection found error F4E3. The error is motor failure, ran the unit in diagnostics mode and the motor never came on. Installed a new motor and retested, the unit is operating as designed. No warranty leaks detected during service."

Arrived onsite for damaged panels. Replaced damaged compressor compartment cover and front panel. Job complete

Unit A. Arrived onsite for unit not latching and not starting a cycle. Inspected and found failed strike. Replaced strike. Unit is now functioning properly. Job complete

Arrived on site to install previously ordered part. Replaced water valve. Test unit and is now operating as designed. No leaks present at this time. Job complete

Arrived onsite for unit not making ice. Upon arrival inspected unit. Ran test 96 and confirmed valve is functioning but no water to ice tray. Ice maker motor is cycling properly. Tested and found failed fill tube heater. Replaced and tested. Unit is now functioning properly. No leaks present at this time. Job complete

"Arrived on site and found no ice production, found freezer temperature it is showing 13? removed evaporator cover and found Frost pattern is good but there is ice on the left-hand side of evaporator blocking airflow to icemaker, took pictures. Used steamer to remove ice buildup and requested the customer continue to monitor for correct operation of the next several days, job complete"

Arrived on site to test unit for no power. Found unit receiving proper voltage. Found console not connected. Secured connections and installed zip ties to ensure connection doesnt pop out of place. Unit now working as designed. Job complete.

Arrived onsite for a wall oven the has no power. Upon inspection I found that they was no power going into the unit at all I checked the that breaker was not tripped I found that it was not but I reset it anyway and tested again and tested l1 and l2 and found no power still. I advised the customer to check the oven circuit.

"Arrived on site to,install previously diagnosed and ordered parts. Due to the compressor failure, I led and replaced the compressor, access valve and UV dye drier. Vacuumed the system and pressures held good. Installed 8.11oz of R134a refrigerant and monitored pressures. Pressures held good and unit is beginning to cool. No water leaks observed during service, job completed. I recommended they allow the unit to cool for 48 hours before placing items back inside."

"Arrived on site to diagnose dryer that is not heating at all. Examined unit and found the heating element ruptured. Provided estimate for new heating element. Replaced heater and vacuumed unit out. Tested unit and confirmed proper function. Customer advised they need to clean the vent to prevent any more issues, large lint buildup was present. Repair completed."

"Arrived on site to install previously diagnosed and ordered parts. Due to the gearcase, cam and belt failures, I removed and replaced the mentioned parts and calibrated. Tested the unit and found the actuator has failed as well. I removed and replaced the actuator and calibrated again and retested. Unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site. Replaced deli harness,replaced freezer evaporator fan motor that includes defrost thermistors,powered unit on ran diagnostics all test passed deli ui working as designed.

"Arrived on site for LG refrigerator, inspected unit and work area. Customers complaint was unit not cooling. At arrival unit is on and running, compressor was humming and fans are also operating. No signs of defrost witch means the sealed system has failed and will need to be repaired. Customer has decided to no proceed with repairs. /

"Arrived on site for no water or ice. Tested water dispenser no water dispensing,test measure fill same issue no power to valve,power cycled unit same issue,deli control working correctly,ran diagnostics tested paddle test passed tested force fill working. Exited diagnostics water dispenser working possible issue with controls ran icemaker test passed harvest ran fill failed. Advised customer on replacing controls and heater or just the fill tub heater customer will call into the office if they approve repair.

"Arrived on site and inspected dishwasher and found right hand side linkage pulleys have broken off of mounting point on dishwasher. After replacement door is working properly. job complete"

Arrived on site and and found Customer complaint was this is the noisiest washer theyve ever owned. Previous washer in the home was 20 years old. Set washer into a diagnostic cycle and didnt find any saved error codes. ran all functions manually and discussed what every noise is And its related function with customer. Discussed correct loading for this model and detergent usage. Washer is operating as designed documented with tech line. 7736475727

"Arrived on site for washer making abnormal noise during agitation. Upon arrival confirmed sound during agitation. Found no errors in diagnostics, and found no voltage issues. Inspected rotor stator and slider but found no cracks, breaks, or oil leaks. Retested unit in multiple cycles but couldnt replicate noise. Instructed customer to let us know if issue returned.

Arrived on site for not heating. Upon arrival test unit. Unit tumbles but does not heat. Did polarity test and test failed. There is no voltage from L1-N. Showed readings to customer and Uploaded picture on SD. L2-N is correct with 119v. Customer signed incoming voltage waiver

Arrived onsite for a MW that is not heating. Upon inspection I found that the diode had failed. I installed the diode correctly this time and tested the unit using a resettable fuse and found the unit operating as designed. I am ordering a fuse and setting return

Arrived on site for kerosene smell. Upon arrival inspected unit. There are no gas leaks detected. Test unit and operates correctly. Found that home had lots of staining and varnishing done. The kerosene smell is from chemicals used during home improvement work. Customer states that the smell has slowed. Let customer know that the smell will eventually pass. Unit is operating as designed. Job complete.

"ZISB42DCA Arrived to inspect no ice. The customer said the unit made about ten cubes, shortly after the sealed system repair, but then never produced any again. I found the FC at 25?, too warm for production and the RC at 41?. I found pressures were outside of expected ranges and after 20 min. at rest, the system was still 20psi on the high side. Frost pattern was minimal and only at the entry point. Office to schedule return service for sealed system. No leaks observed during service. ; O-emld tckt"

Arrived onsite for unit not cooling. Upon arrival inspected unit. Found unit room temperature in both compartments. Checked amp draw on compressor and was .4amps. Checked pressures and was 10psi. Inspected compressor and evaporator compartment and found no signs of dye. Ran nitrogen through unit and found leak at center divider. Removed hinge screw and found screw covered in dye and dye underneath hinge . Called tech line for assistance. Spoke to Andrew SR#7736478302. Submitting pictures. Submitted for review. Whirlpool will contact customer within 3 business dayS

Arrived on site for upper rack falling down . Found left front wheel assembly wheel broken off and not staying in track. ordrng 1 WPW10571738 (Wheel)

"Arrived on site for lid not locking. Upon arrival test unit and selector knob is not responding. Removed console to access controls. Cleared lint build up from controls board. Found a loose connection. Secured all connections. Test unit and knob now responds. Started several cycles , lid latches and cycles begin every time. Unit is operating as designed. Job complete

"Arrived on site diagnose washer that is vibrating and banging when spinning. Tested unit and confirmed excessive vibration, and banging. Found the hub teeth worn out, causing the basket to vibrate by on the shaft. Advised we need a new hub and to test, and suspension may be needed.

Arrived on site to test unit for water leaking into RC and freezing items. Found drain was restricted and unit way over packed. Accessed drain tube and found it was not sealing properly causing air leak. Also found gap in liner and cabinet. Sealed liner with silicone and sealed drain tube to prevent air leaks. Removed obstruction from drain and unit now working as designed. Advised unit will need to be unpacked a bit to allow for proper air flow. Job complete.

"JGP932SEC2SS Arrived to inspect weak ignition on RR burner. The unit will require the ignition module. Customer has requested tech GC. Office to contact the customer the arrange return service. No gas leaks detected during service. ; ordrng 1 WB13T10046 (Ignition Module)"

"Arrived on site to test unit for no ice production. Customer stated she ran a clean cycle and replaced filter and it never produced after that. Found water filter was not installed all the way preventing unit from getting water. Ran diagnostics and found reservoir drain receiving proper voltage(13vac) but not engaging. Removed pump and inspected, found no obstructions. Reassembled and pump now working as designed. Advised to monitor and if unit stops making ice recommend reservoir pump W11542868.

Arrived onsite for refrigerator not cooling. On inspection the FC was 39? and the RC was 49?. Gain access to the FC and found a ice ball up in the right corner of the evap. Defrosted the evap and tested the thermistor (12.9k)and the thermostat (55k) both good. Looked at the door gasket and they were fine. On further inspection found the gasket that goes on the door that seals the icemaker to the door was bad. Order a seal. Office to reschedule when part arrives and no water leaks detected during service.; ordrng 1 WPW10287601 (IM gasket)

Arrived on site and replaced previously diagnosed latch. Unit now working as designed. No leaks detected. Job complete.

Arrived onsite for a range with front right burner that is not turning off. Upon arrival a found that this is true. Upon testing I found that the control will need to be replaced to resolve the issue. I am ordering the control. ordrng 1 316272401 (Control)

Arrived on site to test unit for unit not getting hot. Test unit and found and glow igniter. Replaced igniter

"Arrived onsite to replace faulty parts. Upon disassembly found basket shaft sheered of from the rest of the basket. Tried removing spanner and block, but seized to gearcase shaft. Unit will need complete rebuild.

"Arrived on site to diagnose refrigerator that was not cooling. On arrival the unit was powered on but silent. No fans running, no compressor. I power cycled the unit and retested. When I power cycled the unit things powered on, compressor came on, fans were running normally. Advised customer wait 24 hours to see if unit cools and stays cooling. If compressor stays running and unit doesn't cool then customer is advised on needing a Sealed system repair, or possibly a control if unit locks up again. No repair made since unit needs time to run and may be resolved now. Repair completed."

"Arrived onsite for a washer that is not spinning the clothes out when set to the normal cycle. I found spin turned off in the normal cycle and showed the customer. I explained to the customer that the washer will automatically default to what options were selected and run dining the previous cycle. I checked stored error codes and there was a slow fill, off balance, and suds error code. I went over detergent and loading. The customer stated they had just cleaned the hose screens and when I ran the auto test cycle the machine filled properly and worked as designed.

"Arrived onsite for a dryer not heating. I tested the incoming voltage and had 123VAC L1-G, 12VAC L2-G, & 110VAC L1-L2. I reset the circuit breaker and had 243VAC L1-L2. The breaker didnt lock in strong like it should when resetting it. I ran the dryer and lost L2 and could smell a faint electrical smell coming from the wall receptacle. I disassembled the dryer and inspected the L2 circuit at the control and all the heater components. All tested good and visually looked good. I went over all this with the customer and they are going to pull the receptacle and change it then test the dryer and if needed have the breaker replaced. Call complete."

"Arrived on site for dishwasher, inspected unit and work area. Customers complaint was error code F2E2 for lost communication of UI. Found that the user interface was good and no corrosion was found. I then found that the control was causing the problems. I then ran a diagnostic cycle and found everything operational good. No leaks where observed during service. /

"Arrived on site. Replaced left side door hinge,screw and cam tested door operation good.

"Arrived on site to test unit for front right burner not igniting, tested unit found no loose connections in spark module, moved connection over to the other burner and it is still not sparking, need front right igniter and spark module as precautionary, ordering parts, office to reschedule ; ordrng 1 W11590249 (Spark module) and 1 W11666003 (FR igniter)"

Arrived onsite and found unit thickly frosted in the evap causing cooling loss. Advised customer on manual defrost and will return Thursday to follow up. Suspect wiring backed out of molex.

"Arrived onsite and found unit with crack. Sr#7736476514 techline will have us patch the crack to repair, advised customer can follow up with customer care with any other questions or concerns. Customer does not want unit to be repaired before pursuing replacement with whirlpool customer care. ; O-emld tckt"

"Left side panel, belt, retrieve vent screw from blower housingArrived on site to inspect dryer noises. Upon further inspection, I turned the unit on and immediately it began to make a clanking noise. I raised the top panel and tested again and found the left side panel badly dented inward. Also found the belt beginning to fray. I am ordering the left panel and belt and CNOTE-2HOUR JOB and office to schedule return service. Also, returning tech will need to retrieve the vent screw from the blower wheel housing at the back of the unit. Unit left unplugged for safety and no lint observed during service.; ordrng 1 8533643 (Cabinet) and 1 CNOTE (2 HOUR JOB)"

"Arrived on site to diagnose dryer that is not starting cycles. Tested unit and found proper voltages and polarity. When I plugged in unit I could hear crackling coming from the timer. I replaced the timer and tested the unit. Unit does not start. Confirmed that the push to start button tests good, door switch good. All safety devices working as designed. Issue has to be in the timer / motor. Ordering time and motor to resolve. Office to schedule. ; ordrng 1 279827 (Motor) and 1 WPW10450286 (Wiring Harness) and 1 W10857612 (Timer)"

Arrived on site for odd smell . Ran diagnostics and found flame was not correct . Found house is on LP not natural gas . Will need to convert to LP. Ordering LP a kit . Customer also has venting issues to address on house side . No gas leaks at this time. ordrng 1 W10606694A (Lp kit)

"Arrived on site for fridge not making ice . Ran diagnostics,got E5 code . IM wouldnt run harvest , timed out . Found ice maker stuck upside down in a flex . Ordering ice maker . Call to set return . No water leaks detected at this time. ; ordrng 1 W11115534"

Arrived on site for fridge not making ice . Got E5 errror code in diagnostics. Unit will fill but not harvest-ordering ice maker . No water leaks detected at this time. Call to set return; ordrng 1 W11658802 (Ice maker)

Arrived on site to test unit for display on board turning off when oven get to hot. Found board shorting out with the head from the vent under console. Will order new board reschedule for Tuesday the 30. When display goes off the cooktop still works so its still getting power but no display. ; ordrng 1 W11126814 (Control board)

"Arrived on site for range, inspected unit and work area. Customers complaint was oven not igniting properly. Tested and found a bad igniter replaced and same issue. Im re-ordering the make igniter and returning with the manifold to replace both. No leaks where observed during service. ; ordrng 1 W10764654 (Bake burner) and 1 WPW10324262 (Igniter)"

Arrived on site. Per customer water or ice will randomly dispense from dispenser ran diagnostics all test passed ordering a new ui and main control. ; ordrng 1 W10848301 (Ui) and 1 W10843055 (Main control)

"Arrived on site for dishwasher, inspected unit and work area. Customers complaint was unit would not work properly. Tested unit and it will need the UI AND CONSOLE replaced. Im ordering parts and reschedule. No leaks where observed during service. ; ordrng 1 W11460908 (Console)"

"Arrived on site to test unit for scrapping noise, tested unit found front panel clips broken causing drum to move excessively in cabinet, rear drum felt gasket failed causing drum to rub against metal bulkhead damaging it, will need to replace panel clips, repair kit and drum to fix issue, ordering parts, offer to reschedule ; ordrng 2 WP98234 (Clips)s and 2 W10854425 (Clip front panel)s and 1 W10899578 (Drum)"

"Arrived on site and found old style tub Ring is still in place,per service pointer W11651001 It will need to be replaced with a new stock. Ordered replacement.; ordrng 1 W11094304 (New style tub Ring)"

Arrived on site for front left and front right burners clicking but taking too long to ignite. Upon arrival test unit and found electrode intermittently not giving a good spark. Need to replace burner heads for both right and left front burners. Replaced front left burner head and unit ignites correctly. Need to order burner head for front left. Office to reschedule ; ordrng 1 WPW10515455 (Burner head)

"Arrived on site to diagnose oven that would stop heating when running. Spoke with customer who clarified that when the door was opened the cycles would stop and she would have to reset the cycle to get it to restart. She also had difficulty getting button presses to work on the console, and there was a crack on it. Ordering a new console to resolve. All issues can be tied to steam hitting console/cracked panel causing all issues. Changing panel and updating software should resolve. Office to schedule when part arrives.; ordrng 1 W11600370 (Console)"

Arrived onsite for damaged panel. Upon arrival inspected unit and found damage control panel. Took pic. Ordering panel. Office to reschedule ; O-emld tckt

"Arrived onsite for new unit, scratched. Upon arrival inspected unit. Found scratch on right side of outer cabinet . Customer requesting touch up paint. Ordering parts research for grey touch up paint. Office to reschedule. ; ordrng 1 Partsresearch (Grey touch up paint)"

"Arrived onsite for unit making scraping noise. Upon arrival inspected unit. After running unit for a few minutes noise was apparent and increased as unit continued to run. Disassembled and ran test. Found that unit element would not cycle. With element assembly disassembled the scraping noise went away. It seems like the unit is overheating and causing the panel to warp and rub. Attempted to replace element assembly however assembly was damaged in box, Element defective. Reordering element assembly, heating duct and rear bulkhead. Need 2 hrs. ; ordrng 1 W11519683 (Heating element) and 1 W11519685 (Heater duct) and 1 W11516794 (Rear bulkhead)"

Arrived onsite for a refrigerator to replace the previous diagnosed parts. When I arrived I found the customer had emptied out the unit but both compartments were cold and at temp. The customer stated this is whats been happening and sometimes when it stops cooling he can hear the overload tripping on the compressor. I turned the temp down and when the compressor tried to start it stayed at 6.5 amps and tripped the overload. I pierced the drier to remove the refrigerant and had no pressure. I cut the steel line and the capillary tube at the drier and still nothing came out. I cut the high side line at the compressor and nothing came out. I cut the low side line at the compressor and refrigerant and oil would come out and stop. I would hear oil gurgling in the suction line and more would come out. I gained access to the evaporator and it had a full frost pattern and the lines were not kinked. I explained to the customer that the evaporator has to be full of oil for this to be happening and we will need to replace the evaporator also. I will blow thru the yoder loop and condenser with nitrogen when I return but am ordering the condenser just in case it is needed. Ordering W11550396 evaporator and W11644420 condenser. Office to RS.; ordrng 1 W11550396 (Evaporator) and 1 W11644420 (Condenser)

"Arrived on site to diagnose microwave oven combo that has a failing gasket. Examined unit and found that what looks like rubber or a seal is sticking out of the front panel glass. Ordering a new outer door to resolve, looks like it wasn't sealed right at the factory. Office to schedule when PSP item arrives ; ordrng 1 W11600215 (Outer Door)"

"Arrived on site for dryer. To heating upon arrival confirmed issue. Found cause of failure was broken terminal block as well as damaged wiring, was able to temporarily redo wiring and found unit heating as designed but found terminal to damaged behind screws to hold wires properly and rescheduled customer for 05/20/23 to complete repairsW11164044 harness/terminal).; ordrng 1 W11164044 (Harness) and 1 Cnote (Harness has all the pieces of terminal needed for repairs.)"

Arrived on site for ice machine not making ice. Upon arrival confirmed issue and found bin empty. Checked equalized pressures and found them at 60 high/low. Ran unit and found psi lvls at 160/-15. Replaced drier and recharged system. Found psi lvls equalized at 60 again then found run time pressures at 125/-5 but evap plate wasnt frosting over. Found no leaks in system and low side pressure would equalize back to 60 psi when powered off within 4 seconds indicating weak compressor windings. Will need office to reschedule once availability of parts is known.; ordrng 1 W10536005 (Compressor) and 1 2313624 (Condenser coil) and 1 W10218037 (Evap) and 1 W10843121 (Non uv drier) and 1 W10913906 (Access valve)

Arrived on site for knob issues. On inspection the timer will not advance once set on time. Everything is working ordering a timer W11566735. Office to reschedule once part arrives.; ordrng 1 W11566735 (Timer)

Arrived onsite and found unit operating with failed pump. Unit was installed unconventionally without brackets and could not be safely removed in a timely manner. Advised customer that the unit had been installed without brackets and would need to be made accessible to allow for repair. Customer requested that the sump assembly be left onsite to increase the likelyhood of a sameday repair once the unit is uninstalled. ; ordrng 2 WP8269145 (Mounting bracket)s

"Arrived on site for dryer noisy while running. Found rattling is coming from broken fan blade. Will need a new one, housing, and motor to complete repair it. At this time dryer is still heating properly and found a vent flow to the exterior of the apartment building is showing restricted. Recommended that apartment maintenance correct this before return visit.; ordrng 1 W11327190 (Blower wheel) and 1 WPW10211911 (Blower housing) and 1 W11234001 (Motor)"

"MVW7230HW0 Arrived to inspect shaking. I found the legs were not set correctly and the unit would rock, corner to corner. I corrected the legs and centered the basket within the chassis and re-calibrated. The unit operated in manual and automatic test modes as designed. No leaks observed during service."

"Diagnosed a defective led module,per service pointer removed all leds,installed updated leds all leds working as designed. AUTHO S84638 ; used 4 W11632139 (Led module) from stock"

Arrived onsite and tested unit for leaking. No leaks detected. Corrected felt pad alignment to improve rotation of drum. Unit is now operating as designed with no leaks. All checks good. Advised customer on repair.

Arrived onsite and replaced left side support and feet. Unit is now operating as designed. All checks good. Advised customer on repair.

Arrived onsite for broken microwave panel and repaired unit with new console. All checks good. Advised customer on repair.

Arrived onsite and found lid unlock failure due to bent lid. Corrected lid to con vex position and function is now restored. Advised customer on repair. All checks good.

Arrived onsite and found dishwasher water had not been turned on to unit. Repaired by turning on water to unit. All checks good. Advised customer on repair.

Arrived onsite and replaced the freezer door to restore ice maker production. Unit is now operating as designed. Advised customer on repair. All checks good.

Arrived on site and replaced previously diagnosed ice door/separator. Unit now working as designed. Job complete.

Arrived onsite to install previously diagnosed parts. Upon arrival I installed the new door and found the unit sealing up properly now W16VNS0APL1

"Arrived onsite for a DW that is flashing all lights on the console. Upon arrival I ran the unit and found that this did not happen. Due to the seemingly intermittent nature of the issue, I replace the control and tested the unit several time and found unit operating as designed"

"Arrived onsite of a vent hood with light that flicker on the low setting upper inspection I found this to be true. I contacted Rich as techline and toll him of my findings and found out that there was nothing I could do to fix the issue it was explained to me that it has something to do with how our power is delivered here in the u.s, the way the bullies pick up the high side of the sign wave more what the low side causing a perceptible flicker i relied this to the customer and advised them to contact whirlpool if they have any questions sr#7736475354."

Arrived on site to relaxed heating element. Replaced element test unit and unit test good job complete.

Arrived on site to test unit for Loud noise when its windy outside. Test unit and can hear the damper opening and closing. Customer advised it only happens when its windy. Advised customer to get with the vent people to check damper on the outside and where the wind is coming in from. Job complete.

"Arrived on site to install previously diagnosed and ordered parts. Due to the control panel being cracked/broken, control clip being broken, upper rack wheel broken, and inner door panel missing screws, I removed and replaced the control panel, control clip, upper rack wheels and installed screws and tested the unit. Unit is operating as designed. No water leaks observed during service, job completed. Customer advised they performed a wash cycle earlier and the unit did not leak.."

"Arrived on site to inspect dryer not operating. Upon further inspection, the customer demonstrated that they can turn the power on, but the dryer does nothing. I disassembled the unit and tested the fuse, cutoff, thermostat and element and found the fuse and element both have failed. I removed and replaced the fuse and element and cleaned the u;it (before & after photos) and reassembled the unit and tested. Unit is operating as designed. No lint observed at the end of service, job completed."

"WRF555SDFZ12 Arrived to inspect items freezing in RC. The issue was isolated to the area near the air vent and I advised the customer to keep items away from the area, unless they have a higher sodium or sugar content. I explained that the vent is where all of the cold air for the RC comes from and the customer will attempt the different loading strategy. I also described changing temperature. Operational test good, no leaks observed during service."

"WDT750SAKZ1 Arrived to inspect no heat. F10E2 was the only stored error code and likely generated during initial installation, and I cleared. Within service test mode, all functions of the unit were present and I verified the heater drawing the expected current. Discussion with the customer revealed they pre-rinse quite well. I advised that this is fine and preferable to many customers, as it prevents eventual buildup and odor, but they must adjust the amount of detergent they use, due to less oils and debris for the detergent to emulsify with. I also discussed the benefits of purging the cold water from the hot water supply at the adjacent sink. Operational test good, no leaks observed during service."

KRFC704FPS05 Arrived to instal previously diagnosed and ordered parts. I removed and replaced the RC door and installed the UI. The unit operated as designed and I set it to standard defrost. No leaks observed during service.

"WDF520PADM9 Arrived to instal previously diagnosed and ordered part. I removed the failed drain tube and installed the replacement. I ran the unit through several tests after making a thorough inspection of the sump and other areas, exposed to water and found no leaks after the repair was completed."

KOCE500ESS20 Arrived to inspect door damage. I verified the microwave door had a damaged area at the top right. I removed and replaced the door and tested. Operational test good.

Arrived on site for no power dishwasher . Found one of the wires had come loose from power cord . Rewired power cord . Unit controls lit up . Ran quick diagnostic wash test . All checked normal. No water leaks detected at this time. Job complete

Arrived on site for washer making noise . Found leveling feet on pedestal were not level. Adjusted feet . Ran 12 test on diagnostics. Unit is performing as designed . No water leaks detected at this time. Job complete

"Arrived on site ,replaced UI . Tested unit . All operations are normal. Job complete"

"Arrived onsite for a vent hood with flickering lights, upon testing the unit several times and found that the light are operating as designed. Job complete"

"Arrived on site for popping sound. Ran diagnostics couldnt recreate issues in diagnostic test,ran normal operating cycle"

"Arrived onsite for dryer making a noise. Ran the unit and could a pumping noise. Gain access to the drum and found the blower wheel was free spinning and hitting the blower housing. I had break off the blower wheel, I installed a new motor and blower wheel. Tested unit and the dryer is operating as designed."

"Arrived onsite for washer making a noise. I ran the unit in diagnostics mode and when it went into agitation cycle there was a loud grinding noise. I flipped the unit and found oil on the sides of the unit. Installed a new gear case, cam and actuator. Retested the unit and it is operating as designed now and no water leaks detected during inspection."

Arrived on site to replace control board and console. Replaced both parts test unit and unit test good job complete.

"Arrived on site for washer, inspected unit and work area. Customers complaint was unit making taping noises on a spin cycle. I ran unit in diagnostics and found no error codes stored. I then ran a high spin and found that the drain hose was taping agains the wall. I adjusted the hose and re-tested and its now running ad designed. No leaks where observed during service."

Arrived on site to install parts previously diagnosed. Installed both doors and name plate. Cleaned with stainless steel cleaned and unit is now good. No leaks where observed during service.

"Arrived on site for washer, inspected unit and work area. Customers complaint was the washer would not detect the door closed sometimes. Inspected the strike and found it it was lose. I tighten the screws and retested. Unit is now operating as designed. No leaks where observed during service. Job completed."

"Arrived on site for water leaking. Found water leaking from hinge assembly,removed cover found leak at fill tube connection,disconnected connector found o ring warped in female end of water line entering cabinet,removed oring reinstalled oring correctly into female connector,reconnected fill tube ran icemaker fill test passed no leaks."

"Arrived on site to test unit for burn smell and rumbling, tested unit found shorted diode, replaced and tested, u it is now running as designed, called safety to document, recommended to safety if issue happens again, then capacitor, diode and magnetron will need to be replaced, at this time job complete"

"Arrived on site to test unit for no ice production and water not dispensing, tested unit found full bin of ice and water is dispensing, customer stated that is is intermittent and it will stop dispensing water for days, removed front and found a loose connection for the paddle and UI not sitting properly in housing secured connection and installed it properly, removed back panel and found control box dangling inside the drain pan, moisture potentially getting on control but did not detect any at this time, secured control box and advised customer to monitor if issues persists then UI and control will be needed, at this time job complete"

"Arrived on site and found incoming power is correct. When dryer is started motor will home but not move. With door switch pressed if drum is spun by hand motor will kick on and run. Disassembled dryer to replace motor and found blower fan is seized. Ultimately had to drill And melt off old blower fan plastic to remove motor. Replaced blower fan and motor and dryer is now running properly, job complete"