Arrived onsite and leak tested for 30 minutes. No leaks. Unit is operating as designed. Advised that unit may be leaking from steam condensation on the granite counter. All else checks good.

"Arrived on site for doors not sealing properly. Upon arrival, inspected unit and found completely un leveled. Leveled unit and doors no close correctly. Have perfect suction all the way around every door. Job complete"

Arrived onsite for unit continuing to run. Upon arrival powder unit. Found drain pump automatically kicked on. Tried running diagnostics but drain pump would stay on. Inspected and found control failed. Replace control and tested. Unit is operating properly. Job complete

"WED4850HW0 Arrived to inspect long dry times. I found the unit was heating, but it was very damp internally. Further testing revealed the venting in the residence was severely restricted and with the venting connected there was very little airflow. Disconnecting the venting, the unit operated and cycled as expected and the blower assembly was operating as designed. I advised the customer they will need to contact the builder to have the venting issue corrected."

"Arrived on site for oven not getting hot enough . Ran temp checks . Recalibrated upper oven 20 digress, lower oven 15 degrees. Reran temp check . Unit is heating properly . Job complete"

Arrived on site for a dishwasher that has a broken control panel. Inspected unit and work area. Did confirm the customer complaint and replace the control panel assembly. Tested the unit and the unit is working. An operating as designed. Call complete.

Arrived on site for dryer not heating correctly. Upon arrival confirmed failure. Found dryer could heat but moister was staying trapped in dryer. Found home had a clog in outside exhaust exit. Instructed customer they would need a dryer vent cleaning to ensure dryer was working as designed with proper airflow. Call complete

Arrived onsite for a washer the is not operating properly. Upon arrival I checked the drain pump and found that the connector was not connected properly it slipped off. I corrected this by replacing the connector with new connectors and tested the unit and found the unit operating as drain no leaks.

Arrived on site to test unit for console acting erratic. Replaced control per service pointer W11682433. Found wash motor is showing signs of failure. Recommend sump assembly replacement. Scheduled for 09/25. ; ordrng 1 W11416362 (Sump)

Unit 120. Arrived onsite for unit leaking. Upon arrival inspected unit. Ran diagnostics and found oversuds condition. The wrong detergent was used in unit causing overflow from door panel. Took picture. Also utensil blocking spray arm from turning freely. Advised customer on how to flush unit to get rid of excess suds. Job complete

"Arrived on site to inspect dishwasher in kosher mode. Upon further inspection, I found the clean light flashing an error code. I advised my customer that the unit is not in kosher mode, but is showing error code F8E4-overfill/switch open. I cleared the code and before starting testing, I removed the toeplate and found a large amount of water in the drip pan below (photo). I found the water source connection with a droplet of water at the elbow (photo). I advised my customer of the leak and removed the drip pan and cleared the water from it (photo). I found water on the floor underneath the unit (photos). I continued with testing and found the water leaking from the valve area. I stopped testing and drained the water and pulled the unit out to inspect underneath the unit. I found the water hose connection cross threaded (photo). I removed the connection from the valve and inspected the threads and they are good. Reconnected the hose (photo) and retested in diagnostics and the unit is operating as designed with no further leaks. I obtained photos of the water damage on the cabinet to the left of the unit; the floors in front of the unit and the floors in front of the refrigerator located to the left of the unit. Customer was able to get a video of the water sloshing under the wood floors at the front of the unit (photo). Unit is operating as designed. No water leaks observed at the end of service, job completed."

"Arrived on site for a wash machine that has a tub that is leaning against the back wall. Inspected unit and work area. The customer advised they were running a load of blankets in the unit and that the unit went completely off-balance, and they have been unable to get the tub to level out sense. Found the tub ring stuck underneath the rear panel bar. I removed the tub ring from underneath that bar and check the suspension. Found the suspension was good. I did advise the customer that they cannot wash those types of loads in this machine due to issues with the problem they experienced. The unit is working as designed. Call complete."

"Arrived onsite for dishwasher not working. On inspection found that the circulating pump is not working. Pump is on order, office to reschedule once part arrives. No water leaks detected during service. ; O-emld tckt"

"Arrived on site to test unit for no ice production. Found error E5(ice maker thermistor out of range). Also found full tube was frozen over. Recommend replacing inlet valve, fill tube heater and ice maker. Also needing to seal fill tube where enters ice maker with permagum. Office to reschedule. ; ordrng 1 W11658802 (Icemaker) and 1 W11087201 (Fill tube heater) and 1 212643 (Permagum)"

"Arrived onsite for sealed system repair. Upon arrival found unit not made accessible. Tried, and unit will not budge. Notified customer that unit will need to be made accessible prior to service visit. ; O-emld tckt"

Arrived on site to replace inlet hose. Replaced hose test unit no leaks present job complete.

Arrived onsite for refrigerator not able to reverse the door. On arrival the customer showed that the holes on the door to reverse it were not showing. On inspection you could see about 1/2 the hole. I took a rill bit and modified the frame so you could see the complete hole. Reversed the doors for customer. During the reversing the door a plastic door shelf got cracked. Ordering bin to drop off the to customer. W10803530; ordrng 1 W10803530 (Door bin)

Arrived on site to test unit for water in drill pan. Removed drip pan and cleared water. Test unit and unit test good job complete.

"Arrived on site with assistance from another tech sm. Removed defective panel,installed new panel checked with customers approval,reinstalled trims tested door operation good."

Arrived onsite for unit not powering on. Upon arrival inspected unit. Found control is powered and sending voltage to console. Console is not responding. Ordering console. Set to return Tuesday 26th.; ordrng 1 W11413566 (Console) and 1 W11406681 (Control)

"KBFN502ESS01 Arrived to install previously diagnosed and ordered parts. I found the unit cold upon arrival, FC 5? and RC 43? and the FC evaporator was completely encased in frost, with ice at the lower portion of the evaporator and defrost element, denoting a working defrost system. Further inspect revealed the FC lower drawer had a rigid, open cell foam block placed in the area of the light switch contact point. The block prevented full closure of the FC door and likely the cause of the persistent evaporator freezing. I removed the block and defrosted the evap, noting the unit started cooling as expected. The customer will contact us if issues persist. Warranty applied to service, no leaks observed during service."

Arrived onsite and found unit intermittently power cycling itself. Replaced the HV control and UI. Was unable to replicate symptom before or after repair. Advised customer to observe for sign of repeat failure. Unit is now operating as designed. Called to report findings to safety. Spoke with Kent. Sr#7737303022

"Arrived on site ,replaced lower harness . Unit is tripping breake when powering up . Replaced motor . Ran calibration and diagnostics wash . All checking normal. No water leaks detected at this time. Job complete"

"MHW5630HW3 Arrived to inspect cycle starting issues. I discussed the issue with the customer and advised on starting the cycles, after selecting cycles. Operational test good, no leaks observed during service."

"Arrived onsite for lost ice production following the filter replacement. Fridge temp was set to 36f and Customer was unaware of need to flush the filter. Icemaker fill line froze, advised customer on thawing line and flushing water for filter replacement. Adjusted temp setting to 38. Harvested in diagnostics. All checks good."

"MED5630HW2 Arrived to inspect difficulty starting cycle. During testing, I found the unit would respond to temperature settings very erratically, skipping settings and randomly changing. I removed and replaced the console and tested. Operational test good."

Arrived onsite for a refrigerator to replace the previous diagnosed parts. We replaced the lower door hinge and the side trim pieces. The door is working as designed and it is quiet. Call complete.

Arrived onsite to install previously diagnosed parts. Upon arrival we removed the outer door skin to gain access to the bottom hinge and replaced it the reinstalled the out door and tested the unit and found that the door closed properly and the sound is no longer there.

Arrived onsite and replaced the pts switch due to switch intermittently not starting the load. Unit is now operating as designed. All checks good.

Arrived on site to test unit for right hand RC deli drawer preventing door from closing properly. Found right hand rail was not held in place properly with mounting studs. Secured rail and leveled unit. Unit now working as designed. Doors and gaskets are now sealing properly. No leaks detected. Job complete.

"Arrived onsite for icemaker not working. On inspection the water pressure was good, the FC temp was 1?. Ran service test 56 and got error E5 thermistor bad. Ran service test 58 tested the thermistor and it said it was a to warm for icemaker to make ice. Ordering a RC icemaker W11658802. Office to reschedule when part arrives. No water leaks detected during service. ; ordrng 1 W11658802 (RC icemaker)"

"Arrived on site to inspect refrigerator ice maker not working. Upon further inspection, I tested temps in the left FC compartment=0 degrees. I tested the ice maker and it harvested as designed and I could hear the valve opening. I checked the fill tube line and found it blocked with ice. Following service pointer #W11560805, I am ordering the ice maker, valve and fill tube and office to schedule return service due to the availability of the ice maker. No water leaks observed during service.; ordrng 1 W11455232 (Ice maker) and 1 W11677731 (Fill tube)"

"Arrived onsite for washer making a grinding noise. On inspection ran the unit In diagnostic and the noise was not there. Customer showed me a video of the noise and it was a plastic grinding noise. I gain access to the bottom of the unit and found a white powder in the pulley cover, pulled the cover and dropped the clutch and the teeth on the pulley were round off. Found the teeth on the clutch were round off to. Did not see any oil or other evidence of any other issues. Replaced the splutch and tested the unit. It passed the diagnostics mode, true test will be with clothes in the unit. No water leaks detected during service."

Arrived on site to test unit for loud tapping/knocking sound. Verified noise caused by damper opening/closing. Recommend damper replacement. Scheduled for 09/25. ; ordrng 1 WPW10479155 (Damper)

"Arrived on site for refrigerator needing previously diagnosed ice maker, upon arrival reconfirmed failure and installed ice maker. Retested 7nit and found no leaks and ice maker working as designed. Informed customer to allow for 24-48 hrs to fill bin. Call complete."

"Arrived on site to install previously diagnosed and ordered parts. Due to the sealed system having a leak, I was to performed a sealed system repair. However, when I pulled the unit out onto my floor protector, I found the water line was too short to pull the unit all the way out. Since customer was not home, I contacted them and advised of the situation and that either they would need to pull the unit out and disconnect the hose or I would reschedule to get another tech to assist me. I am ordering a CNOTE-2ND MAN and CNOTE-AUTHORIZATION. Office to,schedule return service. ; ordrng 1 CNOTE (2 man job) and 1 CNOTE (AUTHORIZATION)"

"Arrived on site for refrigerator needing previously diagnosed drip pan,cover, and sh8ms due to ice forming under rc evap. Upon arrival reconfirmed failure and found ice build up in drain line of rc due to clogged drain line behind unit, cleared drain and siliconed drain hose back on to prevent air leaks. Replaced previously diagnosed parts and found unit working as designed. Informed customer to give unit 24 hrs to stabilize temps. Call complete"

Arrived on site to replace previously diagnosed drum. New drum was damaged in box. Needing to reorder drum. Needing to inspect drum prior to ensure no damage. Office to reschedule. ; ordrng 1 W10381481 (Drum)

Arrived on site for water issues. Adjusted water lines behind drawer tested water dispenser working adjusted settings

"Arrived on site for no,ice. Removed bin found extension stuck on icemaker housing adjusted extension icemaker ran through a cycle dumped ice and filled with water."

Arrived on site to test unit for no power. Found breaker was tripped. Reset breaker and verified unit now working as designed. Advised customer to monitor and if issue persists to have contractor replaced faulty afci/gfci breaker. Job complete.

"Arrived on site for no ice. Removed bin found icemaker tray warped and upside down,replaced defective icemaker,ran harvest test passed ran fill test passed."

Arrived on site for no ice. Ran diagnostics E2 error code ran harvest test failed ordering a new icemaker ; ordrng 1 W11658802 (Icemaker)

"Arrived on site for a washing machine that is still making abnormal sounds during the spin portion of the cycle. Inspected unit and work area. The customer advised that the sound generally happens during the medium spin between the wash cycle and the rinse cycle. She advised that the heavier the load, the less the unit makes the sound, but it will still make the sound. She also said that during the final spin , the noise will be less prevalent at higher speeds. I checked the suspension and found the suspension was good. Ran the unit through diagnostic testing, and everything ran and operated as designed. I checked underneath the unit and found it a slight issue with the belt slipping on the cam. I spoke to GC and was advised to replace the belt, Kim, and actuator in case, if the shifter wasnt properly shifting the unit into a proper spin and causing possible, rubbing sounds. Went ahead and replaced all three parts. I called Whirlpool techline and spoke to Butch SR# 7737233030. I advised him as to what has been done to this unit and all of my checks. The customer requested to show him a video of the sound that she was hearing. He advised that the video did not sound completely abnormal in regards to these units. He stated that because this unit is filled with a lot of mechanical parts, that she may be hearing noises that she may have heard before or new noises from these units, but that because the unit is fully operational and working as designed, he would not repair any other parts due to, the complaint, the customer is giving. Advised that based on what the customer is saying, there is nothing that he can say that would be an issue with the unit, and that there may be some issue with the hoses off the back of the unit or water inside of the water ring making more sound during lower speed spins. The unit is working as designed. Call complete."

"Arrived on site for unit not draining and door locked. Upon arrival customer stated that she pulled out filter and drained about a gallon of water. Once water was drained, door then unlocked. Ran diagnostics and got error code F03 drain pump failure. Ned to replace drain pump. Replaced drain pump and test unit. Ran a quick cycle and unit operates correctly. Ran a rinse and spin cycle and unit operates correctly. Unit is now operating as des. No leaks present at this time. Job complete"

"Arrived on site for washer making a grind8ng noise during agitation at beginning of wash cycle after filling. Upon arrival confirmed noise failure and traced it back to rotor/ stator motor, then found slider completely cracked and splitt8ng as well as rotor teeth breaking down. Replaced rotor and slider. Retested unit. Found noise removed and washer working as designed. Call complete"

"Arrived on site for cycle not advancing and sensing light just blinks. Upon arrival, ran diagnostics and there are no saved error codes. Ran manual test and all components operate correctly. Ran automatic test cycle and unit operates correctly. Found issues customer is have is per service pointer W11648603 for 2 step start behavior. Instructed customer on use and there is no longer issues. Unit is operating as designed. No leaks present at this time. Job complete"

"Arrived on site to install previously diagnosed and ordered parts. Due to the unit not heating properly, I removed and replaced the magnetron, capacitor and diode and tested. Unit is operating as designed. Job completed"

Arrived on site to test unit for unit not heating. Arrived on site to test unit and found no heat from magnetron. Will order new magnetron and new control board. Office to reschedule ; ordrng 1 W11646740 (Control)

"Arrived on site to follow up on dryer that was not running. Tested unit and confirmed no function. Checked voltages and found good 120/120. Tested safety devices and verified thermal fuse open again, ventilation good. I replaced the fuse and ran temps. I found the temp just kept rising and was not cycling. I replaced the operating thermostat and retested. I verified temps were cycling in the drum with the new thermostat. Unit was overheating due to a failed operating thermostat. Repair completed."

"Arrived on site to inspect dishwasher gasket issues. Upon further inspection, I found the door gasket was hanging off the tub in the upper left corner. I was able to adjust the gasket and set it back in place. Tested the racks by pulling them out and sliding them back in and found when pulling the 3rd level rack out, the slide lock was grabbing at the gasket. I made recommendations on 3rd level rack use and its movements to my customer as there is no repair to correct this issue other than changing the way the rack is pulled out and slid back in. No water leaks observed during service, job completed."

"Arrived onsite and found stripped washplate causing failure to wash. Replaced the washplate, unit is now operating as designed. All checks good."

Arrived on site for wall oven needing previously diagnosed vent. Upon arrival reconfirmed failure and installed vent. Found no further failures. Call complete

Arrived on site for rusty door panel around vent area . Send wrong door . Ordering door and badge . No water leaks detected at this time. Call to set return ; ordrng 1 W11659651 (Ss door panel) and 1 WPW10612925 (Badge)

"Arrived on site to install previously diagnosed parts. Upon arrival I installed the new gearcase, splutch, belt,and actuator.and I tested t unit and found unit operating as designed no leaks"

Arrived on site to test unit for frost building up in FC. Found all gaskets sealing properly. Removed frost off door switch and now working as designed. Sealed gaps between liner and cabinet with silicone. Advised customer to open and close FC door directly from center to ensure FC door closes and seals as designed. No leaks detected. Job complete.

"Arrived on site ,replaced oven burner tube and center burner head . Both are lighting correctly. No gas leaks detected at the time . Job complete"

"Arrived on site to diagnose washer that was not spinning. On arrival customer informed me it seemed like it dod spin, but after they ran their last load they checked it the next morning and stuff was not fully spun out and unit was dead. I tried to power on the unit as got no response. After several tries I was able to get the unit into diagnostic mode, where it threw an F6E2 error for UI not able to hear ACU. Ordering new console and UI to resolve, and possible harness. Office to schedule based on location, autho also needed. ; ordrng 1 W11135391 (Console / UI) and 1 W11401710 (Control) and 1 W10876600 (Drain Pump) and 1 W11409746 (Lower Harness)"

Arrived onsite for unit not functioning properly. Upon arrival inspected unit. Ran unit and unit is functioning properly. Unit heating and running normal. No odors found. Could not duplicate any issues. Customer will monitor.

Arrived onsite to install previously diagnosed part. Upon arrival I installed the new heater and tested the unit and found the unit operating as designed.

"Arrived on site for noise complaint. Listened to recorded let unit run noise is from refrigerant expanding into the evaporator,removed existing sealer,placed two sealer pads one on lower section of inlet of the evaporator and one on upper section of cap tube,placed a larger sealer pad around both pads. Powered unit on let unit run noise no longer present ; used 3 4318168 (Sealer) from stock"

Arrived onsite for unit center burner orifice not converting properly. Upon arrival inspected unit. Found orifice holder stripped. Replaced orifice holder. Tested and unit is functioning properly. Job complete

"Arrived on site to install previously diagnosed parts. Inspected unit and work area. Spoke to TG and was advised to replace just a RCA event, fan control, and user interface due to the unit prioritizing the refrigerator and the refrigerator their masters being off. Replaced all the parts I was directed to and reassembled the unit. Found the unit cooling and operating as designed but to tell the customer to call back if any other issues persist. Call complete."

Arrived onsite to replace faulty door. Replaced freezer door. Unit is cooling properly. Job complete

"Arrived on site to inspect dishwasher door hinge not working. Upon further inspection, I tested the door operation and found it opens too fast. I pulled t( unit out from the cabinets and found the right hinge had jumped off track. I reset the hinge and tested operations and the unit is operating as designed. No water leaks observed during service, job completed."

Arrived site for a wall oven that wont keep the clock time correct. The customer stated the time speeds up. I found the UI defective and replaced it. Call complete.

Arrived on site to test unit for F9E1 error. Did a reset to test unit and unit heating on the microwave side and oven side no error codes. Job complete

"Arrived on site for refrigerator needing previously diagnosed sealed system. Upon arrival reconfirmed failure and installed compressor, evap coil, access valve and uv drier. Pulled vac and recharged system with 68g of r600. Found no leaks and I formed customer to allow 24 hrs to stabilize temps and an additional 3 days after to fill ice bucket. Call complete"

"Arrived on site to inspect washer noises. Upon further inspection, I found the unit had moved itself out from the wall possibly due to it getting off balance. I placed the unit back in its space correctly and placed it in diagnostics. Unit showed no error codes and I continued with testing in test 12. The unit operated as designed. I found the unit rocking back and forth from front left to back right. I adjusted the leveling feet and retested the unit and it continues to operate as designed. I advised the customer of my findings and repairs. No water leaks observed during service, job completed."

(SV) Thin ice complaint. Verified thin ice. Checked reservoir and it was not full of water. Ran diag mode verified pump is working but water level sensor is incorrect. Replaced the RECIRC pump. Ran unit found unit is now filling correctly. Verified harvest. Set ice thickness to max. Job complete.

Arrived onsite for unit not heating. Upon arrival inspected unit. Found heating element failed. Replaced element and tested. Unit is now functioning properly. Job complete

Arrived on site to install new icemaker to resolve no ice condition. Replaced icemaker with new and cycled icemaker. Verified proper harvest completion. Repair completed.

"Arrived on site ,replaced capacitor. Ran diagnostics and all is checking normal. No water leaks detected at this time. Job complete ."

"Arrived on site to test unit for not dispensing ice. Found dispenser motor had a connection that popped loose. Secured connection, unit now working as designed. No leaks detected. Job complete."

"Arrived on site for a MW that stopes heating 3mins into heating up your food. Upon arrived I tested the unit with a cup of water and ran it for 5mins and found the the unit did heat but after 3mins the unit turns off. I am ordering the mag thermistor, control and returning with the mag, cap and diode. Reschedule for the 09/22/23; ordrng 1 W11552018 (CNTRL-ELEC) and 1 W11224856 (THRMST-FIX) and 1 W10832024 (THRMST-FIX)"

"Arrived on site to inspect venthood fan cover cracked and unit not working on low setting. Upon further inspection, I found the blower grill cover is broken and not supporting the blower properly causing the blower wheel to rub on the motor conveyor (photos). According to the manufacturer parts diagram, the grill cover is to be included with the blower assembly and the part prescreened for today does not have it in the box. I am ordering the grill cover and blower assembly and CNOTE-LSO PER CUSTOMER REQUEST and office to schedule return service due to the availability of parts. Unit left unplugged for safety.; ordrng 1 W11099743 (Grill cover) and 1 W11100651 (Blower assembly)"

Arrived onsite and found ui not receiving power. Determined door harness to have continuity. Replaced main control and UI. Unit is still not operating. Verified that the control is generating power to the ui but the harness at the door connection does not have voltage. Reported findings to techline. Sr#7737335406.

"KBFC42FTS03 GP arrived on site to inspect water leaking from underneath refrigerator and ice in the freezer. Upon arrival the FC door was slightly ajar on the right side and there was water pooling underneath the unit and a sheet of ice on the FC floor. Further inspection revealed gapping in the lower right side of the FC gasket and moisture where the gasket should have been in contact with the cabinet. Discovered a square of foam taped to the back of the main FC drawer on the right side making contact with the light switch preventing the right side from fully seating when the door is closed. I suspect that one of the servicer(s) that had worked on the unit prior to Appliance Express, had applied the 1/8 foam, self stick spacer, to prevent some unknown symptom. I removed the non-factory spacer and tested. The door function and fitment was as expected and the gasket started sealing around the FC cavity opening. Operational test good, no leaks of the water supply observed during service."

Arrived on site for unit heating but not tumbling . Found belt broken . Ordering belt . Call to set return ; ordrng 1 W10849499 (Belt)

Arrived on site to install previously ordered part. Replaced console and test unit by preheating to 350. Unit preheated correctly. Unit is operating as designed. Job complete

"KFEG500ESS6 GP arrived on site to inspect range oven not heating properly. Set the unit to preheat to 350 degrees at 2:10 with a starting temp of 79 degrees. After 11 minutes unit claimed to preheat with internal temp of 397. Monitored the heat cycle and temperatures ranged as follows, low 327, high 373, low 323, high 373 averaging out at 349. Unit is operating as designed. Leveled the unit and I nformed the customer of my findings."

KDTE204KPS1 GP arrived on site to inspect drain loop not being adequate. Inspected and found the drain loop slightly lower than ideal. Readjusted and secured the loop in 2 locations to prevent future issues. Gave customer tips on usage. No water leaks observed during service.

Arrived onsite to replace receivers per tech line recommendation. Replaced receivers and had no effect on the door closing and gap was still present on the left side. Call tech line for assistance. Spoke to Andrew-7737173987. Tech sent up for review.

"Arrived on site to diagnose washer not draining. Verified no drain error, and pump just buzzing. The unit is stuck on a drain loop with or without the pressure hose attached. I replaced the control to resolve. Unit still did not drain, likely due to pump burning out. Replaced drain pump and tested. Verified all working aa designed. Repair completed."

"Arrived onsite for a refrigerator not making ice. On arrival I found the bottom of the ice bucket with some ice. The customer stated it was all the ice made in the last 24 hours. I checked temps and found the temperature at the icemaker only getting down to 13 degrees. I tested the FC thermistor and found when it was in a 32 degree ice bath it was reading resistance for 37 degrees and when it was dropping it would show open at times. The thermistor needs to be replaced. The customer has received two orders from Whirlpool for the metal grille and the plastic skirt and both do not fit this unit. The mounting holes for the grille line up correctly but the punch out for the filter housing is an 1 5/16 to far to the right to go over the filter housing. I sent all this info to SR for parts research along with photos. We also called techline and spoke with Steve and we found out someone had put in a parts research for this same issue, SR# 7737341938. Techline had us move the filter housing over to the right and there was another hole there that we mounted it to and the grille fit properly. There was not a hole in the top for the other screw but the filter housing is secure. Ordering WP2188820 thermistor. Office to RS.; ordrng 1 WP2188820 (Thermistor)"

"Arrived on site found deli ui unresponsive,removed ui found broken wires at deli harness unit will need a new deli ui and deli door,tested water dispenser working cause of water issue can be due to broken wires at deli harness. Ordering a new deli door and ui; ordrng 1 W10815668 (Deli door)"

"Arrived on site to install previously ordered parts. Upon arrival,customer indeed has unit thawed. Inspected defrost components and found RC drain pan bowed. Used shims to correct issue. Test drain using quart of water and all water drains correctly. Ran diagnostics to test all components and all components operate correctly. Unit is operating as designed. Job complete"

(SV) Ui not responding correctly. Ui will activate the wrong component. Replaced ui and verified ui function by manual touch to the springs. When properly installed ui will activate on its own. Reverified the ui is functioning correctly on its own. Found glass ui plate is shorting across the buttons. Called TL spoke to Robert. Found glass panel is not replaceable SR #7737335074 Submitted for review.

Arrived onsite and repaired unit by replacing the compressor. Installed uv drier and access valve. Checked for restrictions and leaks. Pulled vacuum for 20 minutes which held. recharged the system with 57g of r600a. Unit is running properly. Advised customer on repair and that normal function should be observed prior to loading the unit full with groceries.

Arrived on site to test unit for condensation build up on horizontal mullion between pantry drawer and RC doors. Switched heater setting to always on per Techline. Advised to monitor. No leaks detected. Job complete. SR#7737337230

Arrived on site to test unit for unit taking for ever to preheat and not getting to temp correctly. Test unit and found broken bake element. Replaced bake element test unit and unit preheated correctly job complete.

Arrived on site to install icemaker per previous diagnosis. Replaced leaking icemaker with new. Unit should produce ice as soon as temps get back to harvest level. Repair completed.

"Arrived on site for a dryer that wont start a cycle. Inspected unit and work area. The customer advised that the unit was working fine and then when she went to change the cycle, it stopped working all together. I attempted to turn the timer knob over and felt, no resistance. Checked the knob and found it broken. The unit will need a new timer and knob for repair. Ordering the knob and the office will need to contact the customer about a return date due to limited parts availability.; ordrng 1 W11675852 (Knob), O-SMS tckt"

Arrived on site to replace control board. Replaced board test unit and unit test good job complete.

Arrived onsite for slow flooding from unknown dishwasher cause. Determined that the inlet valve was weeping into the tube and causing overflow. Ordering valve to repair. ; ordrng 1 W11434044 (Inlet valve)

"Arrived on site for washer not staying balanced during final rinse/spin. Upon arrival found the following errors: F8E1, F5E4, F0E2, F0E1. Inspected rotor and stator and found no failures. Dampener rods were intact. Found inlet valves failing and will need office to reschedule due customer not being available for repairs. Ordering W11316255 valve, W11316256 valve, ; ordrng 1 W11316255 (Valve) and 1 W11316256 (Valve)"

Arrived onsite for a rand with a damaged cooktop. Upon arrival I inspected the top and found that the Silicone was damaged. I will return with the cooktop on 09/22/23; schdld next appmnt for 9/22 FRI !

Arrived onsite to install properly diagnosed parts. Upon arrival I installed the new sump&motor W11613479. And tested the unit and found unit operating as designed

"WRV986FDEM01 GP arrived on site to install previously diagnosed and ordered parts. Installed the LH &RH stops, removed and replaced the adapter and replaced the door gasket. Properly seated and sealed the drain tube and leveled the unit. No water leaks observed during service."

"Arrived on site for a washing machine that will not power on. Inspected unit and work area. The customer had unplugged the unit after the unit was unresponsive and has not tried it since. I confirmed the customers complaint, and as the unit was plugged in, I found the unit stuck in a drain. held down the start button for 5 to 7 seconds for the drain pump to check off and turn the unit back on. On the unit illuminating and working as designed. I ran the unit through diagnostics and did not find any stored error codes. I ran the unit through an auto test, and the unit worked and operated as designed. I started a cycle and found the unit working in operating as designed. I did explain to the customer that if their unit gets off balance that this can happen, and that they just need to press and hold the start button until the drain pump stops to cancel out the cycle. The unit is working as designed. Call complete."