"Arrived on site for no lights. Diagnosed a defective led module,per service pointer removed all leds,installed updated leds all leds working as designed. AUTHO S84638"

"Arrived on site for a refrigerator that is not making ice. Inspected unit and work area. The customer advised that the unit has been making ice on and off for several months, but that it finally just died and has not made any ice over the last several days. Found the icemaker stuck in the middle of a harvest and attempted to jump the icemaker. Found that the motor would not turn. Replaced the icemaker and tested the unit. The unit began to work and operate as designed. Call complete."

Arrived on site to inspect single wall oven. The UI is not responding properly. I was unable to get the unit into diagnostics. I tried cycling power but found no change. I am ordering the UI to resolve. The one I was sent was incorrect. Office to order parts and schedule service. ; ordrng 1 W11600370 (UI)

Arrived onsite for washer making a noise. On inspection had the unit in diagnostics mode and when the agitator started to shake violently and the cap came off and hit the lid. Stopped the unit and gain access to the gearcase found oil every where. Pulled the rotor and found oil all over it. Pulled the clutch and slider found oil on them. Went to pull the agitator off and broke it get it off. Since they have not approved the repairs and I did not have the agitator stopped the repair. Ordering a new agitator and will return next Friday since it is the only day open. No water leaks at the time of service.; ordrng 1 W11550891 (Agitator) and 1 W11551646 (Basket nut.)

On arrival.Verified DW not hooked up. Found drain hose not attached and water line not attached. Installed both correctly and ran diag test. All operations good no leaks detected during service. Job complete

"Arrived on site to test unit for not drying dishes at end of cycle. Upon closer inspection found open heating element. Replaced heating element, tested unit, unit is running as intended. No leaks present at this time. Job complete."

Arrived onsite for unit needing natural gas orifice replacement. Replaced all orifice according to tech sheet. Ran unit and found flame is nice and blue but weak. Customer has a restricted line. Unit was a new install. Customer will contact installer to check for restriction. Job complete

Arrived on site to inspect top load washer running out of balance. I found the suspension worn. I removed and replaced the suspension and tested. The unit now operates as designed. No leaks observed during service.

Arrived on site to inspect dryer. The customer informed me the timer makes a ticking noise when its in the off position. I removed and replaced the times and tested. The door handle has broken off the door. I am ordering the door and handle to resolve. Office to order parts and schedule service. ; ordrng 1 W10861225 (Handle) and 1 W10861224 (Door)

"Arrived on site to replace previously diagnosed door gasket, installed and it is perfect with no ripples on the corners, ran unit and found no leaks unit is running and designed, job completed"

"Arrived on site to follow up on refrigerator that was not defrosting. Checked heater and found it was not correctly installed and sitting in the drip tray. I also found the bimetal bulging in the harness and replaced. I put the unit in forced defrost with bimetal jumped and verified heater came on, and heater positioning was adjusted. Unit working as designed. Repair completed."

Arrived on site for dented cabinet. Found cabinet defective . Reordering part . Customer also mentioned scratched on front panel . Call to set return ; ordrng 1 W10806345 (Front panel)

Arrived on site to inspect side by side refrigerator. The filter door has broken off. Also the ice doesnt always dispense. I found the ice motor running but the gears not grabbing properly. And sometimes the gears strip. I am ordering the ice container and motor gear as well as the filter housing to resolve. No leaks observed during service. ; ordrng 1 W11244434 (Container) and 1 W11162042 (Housing) and 1 WP2220458 (Coupler)

Arrived on site to inspect top load washer noise. I removed and replaced the actuator and tested. The sound is still present. I found the cam has stripped the gearcase output shaft. The gearcase is needed to resolve. I am ordering the geacase cam and capacitor. ; ordrng 1 W11454372 (Gearcase) and 1 W10721967 (Cam)

"Arrived onsite for dryer not drying. On install found heat set for medium turn it to high and found the washer was set to medium spin. I set the spin to xtrra fast to get more water out of the clothes to help the dryer dry them. Informed the customer to wipe the moisture sensor once month to keep them working correctly. The unit heated to 267?, it is getting hot enough to dry clothes. Customer is going to try the new settings in see if it helps. The smell that is in the dry is the new heating element burning off the factory oils. Air flow was good on the unit. SR7737549540."

"Arrived onsite for washer dispensing to much detergent. Found that the unit was set on the lowest soil setting. Did not find and other settings to change the amount of detergent that gets distributed into the unit. The keys are not very responsive to the touch, informed the customer to connect the unit to the WiFi to get software updates. Sr 773754872 WP said there is no setting to change for softener, you can only set the amount detergent going in to the unit. No water leaks detected."

Arrived onsite for unit heeding a gearcase. Upon disassembly found agitator seized to shaft. Will need to break agitator off to replace gearcase. Ordering agitator and actuator. Set to return Friday the 20th; ordrng 1 W11550891 (Agitator) and 1 W11481722 (Actuator)

"Arrived on site to replace display, replaced display. Tested unit, unit is running as intended. Job complete."

Arrived onsite and repaired by replacing door skin. All checks good. Advised customer on repair.

"Arrived on site for a washing machine that is making a clicking noise during agitation. Inspected unit and work area. The customer advised that it is doing the same thing her previous washer did where it will make a clicking sound in the counterclockwise rotation of the agitation. The customer showed me two videos within the past three days where this is done this. I did confirm the customers complaint and checked the agitator. Found no abnormality with the agitator. Checked underneath and did not find any signs of rubbing from the rotor, stator, or slider. I called whirlpool tech line and spoke to Butch Sr # 7737550704. He advised that based on the complaint, the only three things that could cause that sound would be the slider, rotor, or gear case, and to replace all three. Replaced all three parts, and did advise the customer to contact us back if further issues persist. I call complete."

"Arrived on site for icemaker not making ice, found icemaker bail arm not setting properly. Replaced icemaker. Verified operation. Call complete."

"Arrived on site for previously diagnosed parts. Installed the RC gasket and checked for air gaps. No air gaps were found. Customer still say that there is a knocking noise randomly throughout the day. There are no visible issues with the unit, customer said that it is annoying when it wakes him up in the middle of the night."

Arrived onsite site for failed latch mechanism preventing operation. Replaced latch and Advised customer on repair. Unit is now operating as designed.

"Arrived on site to diagnose refrigerator not making ice. Customer said they can hear it cycling sometimes and sounds like it's filling but nothing is coming out. Found an E5 error for the thermistor, which can also be tied to unit not filling. The refrigerator compartment is packed with items and the back wall is fully blocked, which I believe is causing cold pockets to freeze the fill tube since most cooling air is right at the top shelves. I power cycled the unit and advised clearing out the RC and moving everything off the back wall so air can circulate, and function should resume. If this does not resolve we can replace the icemaker and control. Call completed."

On arrival verified complaint of hot water during cycle. Found hot and cold were flipped. Verified all components activated correctly. Correctly installed water hoses to correct valves and rechecked system. No leaks detected during service. Operational test good. Job complete.

"Arrived on site to inspect wall oven microwave combo unit microwave turntable not functioning. Upon further inspection, I tested the microwave and found the turntable not turning. Stopped testing and went into the Tools function and found the turntable turned off. Turned it on and tested the unit and it is operating as designed. Found the unit not connected to wifi and assisted the customer in downloading the Whirlpool app on their phone and connected the unit to WiFi. Retested and unit continues to operate as designed. I made recommendations for use and care, job completed."

"Arrived on site. Tested water dispenser,water dispensing correctly,replaced housing tested working advised if issue reoccurs to install a new whirlpool filter"

Arrived onsite and found unit operating with cosmetic dent from install. Not noticed until after the cosmetic period. Customer will appeal to kitchenaid for warranty care.

"Arrived on site for oven not heating. Upon arrival , inspected elements and are good. Test unit by preheating oven to 350. Unit heated correctly. Customer was not pressing start after desired temperature was selected. Instructed customer on oven operation . Unit is operating as designed. Job complete"

Arrived on site for dryer not heating. Upon arrival confirmed failure. Found stable power supply and disassembled unit. Found element and cuttoff broken. Replaced both parts and tested dryer on heated dry without vent hose and found unit heating as designed. I then found in air fluff setting with vent attached that vent within home was clogged and instructed customer on getting dryer vent cleaning preformed to prevent further issue with dryer. Call complete

Arrived onsite for a refrigerator to replace the previous diagnosed parts. I replaced the FC LED module. All lights are working as designed. Call complete.

"Arrived on site for a wall oven that is not working properly. Inspected unit and work area. The customer advised that the unit seems to have this screen pop up that they lost power when they did not lose power and when this happens, the unit will lose time and will stop The cooking cycle altogether. He advised that before this issue started, time seem to be going fast on his oven clock, and that he was always having to reset it. He advised that he had tried to hook up the unit to Wi-Fi and even called into whirlpool to try to get help with it. He advised that nothing seem to work. I ran the unit through diagnostics and did not find any stored error codes. Checked all connections and found all connections properly seated. Did verify proper voltage to the control and to the user interface. I called Whirlpool techline and spoke to Robert SR# 7737549347. He advised that based on the customers, complaints and issues, the issue would have to be with the user interface, and order the console. he did advise that the customer will need to be hooked up to the Wi-Fi because he stated that when the control senses that the unit needs to be updated and the UI is not hooked up to the Wi-Fi that it can cause issues such as a loss of power message, Ordering the part and the office will need to contact the customer about a return date due to an out of stock and PSP item.; ordrng 1 W11600370 (UI)"

Arrived on site to diagnose dryer not starting or running. Tested and confirmed no start or noise. Removed rear panel and found the thermal fuse was open. Replaced and tested. Verified proper function. Checked vents and found vents clear. Repair completed.

"Arrived on site to test unit for wet clothes at the end of cycle, customer stated that she did laundry and did not remove till the next day and control signaled done but when she opened the lid it had about 6 inches of water, tested unit found cold water valve not closing all the way causing a constant stream of water filling the tub, replaced valve and tested, unit is now running as designed, no leaks detected job complete"

Arrived onsite for unit taking 3 cycles to dry. Upon arrival inspected unit. Removed lint catch and found debris on the backside. Used air flow tester and found that with the unit connected to the external vent hose it recorded poor air flow. Ran same test with unit disconnected from vent and recorded good air flow. Took pic. Unit has External ventilation issues. Unit is heating and tumbling . Customer will notify builder. Job complete

Arrived onsite for a washer that has power but will not start. I found the tub full of water. I tested voltage out of the control to the pump and had 0VAC. I tested the resistance from the control to the pump and had 1.8 ohms. I verified the resistance at the pump and had the same. I changed the pump and the control. I tested the unit in the service diagnostics cycle and the unit completed the cycle and works as designed. There were no water leaks present at the time of service. Call complete.

"Arrived on site for no water or ice. Found frozen water tank due to air leaking out between fan scroll and air tower,defrosted tank and fill tube,added sealer to gaps between fan scroll and air tower ran diagnostics tested icemaker fill passed tested water dispenser passed."

On arrival verified no ice complaint. Ran temps found RC 37 and FC 0. Ice box was 12. FRan component test. Ice box fan and thermsistor passed. Ice maker failed with an E5. Order ice maker W11658802 for return. No leaks found during service. Office to RS. ; ordrng 1 W11658802 (RC ice maker)

"Arrived on site for washer not working, spins and is loud while running, and banging against the side. Customer turns it off when doing so, No error codes. Found unit was not level at all. Properly leveled. Found unit cannot find center of balance. Drain pump working. Water filling. When getting up to speed I can hear gear case rubbing. Agitator teeth are worn almost due. Recommend new gearcase, suspension, agitator, cam and actuator, over authorized amount, need approval. Advised customer they will be contact if approved. ; ordrng 1 Authorization (Authorization)"

Arrived on site for dryer not working. Found knob is just turning. Removed and confirmed knob is needed. Used different knob and found timer a bit restricted when turning. Operates properly. Will need new knob and timer. Also found vent is restricted in wall. Left unplugged from vent. Will need vents cleaned. Reset for wed am. ; ordrng 1 W11675852 (Knob)

Arrived on site for dishwasher not filling with water. Ran diagnostics and had no errors yet. Found harness was not inserted all the way to valve. Corrected and turned water on. Confirmed water now coming in and dishwasher is working as designed. Call complete.

Arrived onsite for unit making noise. Customer advised it was after getting ice and refilling. Ran test and found noise coming from Dual valve. Ordering valve and set to return on the 19th.; ordrng 1 W11548535 (Dual valve)

Arrived on site to inspect range. The cooktop is broken. I removed and replaced the cooktop and tested. The unit now operates as designed.

"Arrived onsite to replace inefficient compressor. Replaced compressor, dryer and access valve . Pulled vacuum and held. Charged per spec and tested. Unit is running and functioning properly. Notified customer to monitor over 24-48 hrs. Job complete"

Arrived onsite for a refrigerator to replace the previous diagnosed parts. I found ice on he evaporator cover and after pulling the cover off I found an ice and frost block under the fan and on the capillary inlet. I found the compressor only starting about every fourth try and tripping the overload all the other time and drawing 9 amps when tripping. I tried a different start device but had no change. I found the system fully charged. I changed the compressor and drier. I added an access valve to the compressor. I vacuumed the system and charged it with 5.25 ozs of R134A. The unit had good pressures and was working as designed. Call complete.

KDTE234GPS0 arrived on site to inspect a dishwasher tripping the circuit breaker. Upon arrival the customer stated that the circuit breaker trips at the beginning of the cycle. Cycled the breaker and the light blinked 6 times. Per the circuit breaker manufacturer 6 blinks is a fault that requires the unit to be replaced. Cycled the breaker and the unit stopped blinking. Ran service diagnostic test on the dishwasher and found that all of the components are working as designed with no water leaks observed during service. This requires safety call. But they are closed. Office to call safety with details.

"Arrived on site for unit not operating. Upon arrival, test polarity and is good. Ran diagnostics and got error code F7-E4 basket re engagement failure, and F6-E3 ACU cannot hear MCU. During test had to unplug and plug unit several times. Found all lower components have gearcase oil on them. Inspected slider and appears good. During test clutch does not activate slider. Need to replace Control, console, gearcase. Slider, clutch,washplate, stator, rotor. Need Autho. Office to reschedule ; O-emld tckt"

"Arrived on site for leaking and disposal overflow. Upon arrival, ran diagnostics and there are no saved error codes. Inspected unit and found drain, filter and disposal covered with debris. Instructed customer on maintenance of the unit. Cleared debris from all areas. Test unit and is operating as designed. No leaks present at this time. Job complete"

On arrival confirmed complaint for multiple heat issues. Replaced INF Switches for LF RF and RR as well as the corresponding elements. Ran operational test and all checks good. Job complete.

"Arrived on site. Found icemaker turned off,lowered shut off arm icemaker ran through a cycle and filled with water. No charge due to call back on prev tech"

Arrived on site for unit needing calibration and being 50? off. Upon arrival inspected unit tested unit and found unit is cycling within parameters. Found a third-party inspector Did not record temperature properly. Unit is functioning properly. Job complete

Arrived n site to test unit for not cooling properly. Found mullion area in Yoder loop was warmer than usual. Accessed compressor and found compressor box was hot to the touch. Removed access panel and took temp reading of compressor. Found compressor was running at 180degrees. Evap motor and condenser motor were working as designed. Spoke with Techline and found foam piece on top of compressor box was present allowing for proper air flow. Found unit grille was a solid piece and cabinet doors on unit are working against unit preventing proper air flow. This is the customers 3rd unit for doing the exact same thing. No signal around customers home so was unable(after multiple attempts) to document. Needing to call Techline with pics. Needing to provide time frame for calling Techline to allow for proper documentation. SR#7737542257#510(366)5962; O-emld tckt

"Arrived on site to test unit for not all burners lighting, tested unit found rear left burner not igniting, removed back panel and found loose connections on the igniter, connected and tested, unit is now running as designed, job completed"

"Arrived on site for dryer needing previously diagnosed terminal block, kit, and screws. Upon arrival reconfirmed issue and installed parts. Tested dryer and found dryer working as designed. Call complete"

Arrived on site for dryer needing previous diagnosised timer and knob. Upon arrival confirmed failure and replaced parts. Unti works as designed. Call complete

Arrived on site for pantry lid popping off. Removed end cap added spacer between endcap screw and liner tested pantry drawer operation unit working as designed.

On arrival verified complaint of front right corner is up off the counter. Took cook top off and found it is an install issue. Unable to fix install issue as unable to get access to clamp. As well as clamp is digging into the customers cabinet. Advised to have installer come and reinstall unit correctly. Replaced cooktop and foam seals for partial bend in original cooktop. Still doesnt sit right. It will be fixed once installed correctly. Job complete. No gas leaks detected at this time.

Arrived onsite and found burnt and deteriorating door gasket. Ordering new gasket to repair. All else checks good. ; ordrng 1 WPW10535778 (Door gasket)

"Arrived on site for washer, making loud screeching noise. Upon inspection found cam slightly worn no signs of oil present from gear case replace cam and tested, no noise was heard. If symptoms persist recommend gear case, cam, actuator, and control at the same time."

Arrived onsite for cooktop with broken parts. On inspection one of the rubber grommet was torn and there were 2 knobs broken. Ordering new parts to replace. No gas leaks detected during service. Office to reschedule once part arrives.; ordrng 2 W11366438 (Knob)s and 1 W11206740 (Rubber grommet)

Arrived on site for dishwasher leaking agains. Removed door panel. Confirmed vent still causing water and moisture. Removed and replaced vent and vent gasket. Verified air flow through vent tube. Verified operation. No leaks. Call complete.

"Arrived on site for failed knob. Upon arrival, inspected unit and found knob has failed and timer shaft is stripped. . Found Service pointer W11693378. Need to replace timer and knob. Ordering timer and returning with knob. ; ordrng 1 W11685947 (Timer)"

Arrived on site to replace RC door gasket. Replaced gasket and verified proper operation. Repair completed.

"Arrived onsite for dishwasher spray arm broken. Found the spray arm broken, installed the new one and ran the unit in diagnostics mode. The arm was working as designed and no water leaks detected during service."

Arrived on site for a refrigerator that is not making ice. Inspected unit and work area. The customer advise of the unit got stuck in the middle of the hardest and would not continue or make ice. Did confirm the customers complaint and replaced the icemaker. I tested the unit and the unit began to work and operate as designed. Call complete.

Arrived on site for dishwasher not cleaning dishes. Upon arrival confirmed failure and found f4 e3 in diagnostics. Upon further inspection I found the motor receiving 120v but not turning on. Will need office to reschedule once availability of motor is known. Ordering W11613479 motor ; ordrng 1 W11613479 (Sump)

"Arrived on site for washer skipping past rinse cycle and sometimes not starting properly. Upon arrival found f7e6 in diagnostics. Found motor windings both at 5.7 and capacitor functional. Found actuator could shift between agitation and spin settings. Found no rub marks, no oil leaking, or cam or gearcase failures under unit. Found control not sensing correct speed of motor and replaced it. Retested unit and found washer working as designed. Call complete"

Arrived on site to inspect dryer not heating. I verified the issue and found good airflow. I found the heating element broken. I removed and replaced the heating element and tested. The unit now operates as designed.

Arrived on site to test unit for drawer not closing properly. Replaced rails and customer stated unit is now closing better. Job complete.

Arrived onsite and found unit operating frozen fill spout. Updated the m/s and cleared the fill spout. Tested the valve. Unit is now operating as designed. All checks good. Cycled and filled while onsite.

"Arrived on site for a refrigerator that wont make ice. Inspected unit and work area. Took temperature of the freezer section and found it sitting at -1?F. Tested the icemaker and found that it would not turn. Attempted to remove the icemaker, but was unable to. Found the backside of the icemaker cover catching on something. I called Whirlpool Techline and spoke to Robert SR# 7737543721. He advised us to go ahead and yank it out and let him know if there was any damage done to the cabinet. I was able to successfully remove the icemaker and replaced the icemaker. Tested the unit and found the unit harvest and filled as designed. Call complete."

On arrival verified complaint of spray arm came off the sump. Visual check of sump shows no stress or damage. Replaced spray arm and operational check good. No leaks detected during time of service. Job complete.

Arrived on site for dishwasher not working. Will not power on. Found light switch to power dishwasher was off so dishwasher had no power. Ran diagnostics and found no errors. All components working as designed. No leaks. Call complete. Unit is IW

"Arrived on site for refrigerator not cooling and making a loud noise. Upon arrival confirmed failure and found large defrost issue in fc with ice frozen all over evap coil and frozen around fc evap motor, found the following results for thermistors and heater P5-1&2(6.31k),3&4(13.4k), 36.1ohms. Found 124 from hi control to heater in defrost mode. Called techline and reported findings Sr#7737538832. Was instructed based on findings that ui logic wasnt registering when unit needed to defrost. I replaced ui and hv control as well as evap motor asm. Instructed customer to give unit 24 hrs to stabilize temps after I removed all ice from coil and installed parts. Call complete"

Arrived onsite for unit with no display. Upon arrival inspected unit. Inspected wiring and found loose connection. Verified proper voltage to unit but found discrepancy. Inspected further and found Breaker was tripped. Customer stated breaker has recently tripped several times. Ran components test and all components passed without error. Customer stated unit tripped last when heating to 425 degrees. After components test ran cycle at 425. Unit was functioning properly. Notified customer that components that would cause a breaker to trip all test good. Unit is now functioning properly. Advised customer to have builder to replace breaker

Arrived onsite to replace previously diagnosed parts. On arrival found that customer did not give 24-48 hr thaw. Customer stated after previous tech made adjustments the noise and ice buildup stopped. Inspected and and found no buildup. Did however see the freezer door issue. Door was not closing properly allowing warm air in thru the bottom left side. Replaced brackets that included rails. Tested and door is now closing properly. Job complete

"Arrived on site found stopper was missing from top rack, instructed customer proper re-install of stopper. Tested unit unit is running as intended. Job complete."

WRS315SDHM08 arrived on site to inspect refrigerator making noise. Upon arrival I found the unit to be operating as designed. Inspected and found evidence of prior freeze up on the evaporator cover. Also found gapping in the chassis on the lower left FC compartment. Adjusted to solve gapping issue. Tested and made sure the evap heater and thermistor were within operating range. Advised the customer on use and care of the unit. No water leaks observed during service.

"Arrived on site for wall oven randomly showing of PF error message on display without tripping breaker. Upon arrival found no errors in diagnostics, upon further testing found ACU sending stable voltage to ui but ui would randomly shut down and restart. Found ui wouldnt connect to WiFi and couldnt be updated. Ordering W11600370 ui (stainless) to complete repairs. Office to reschedule once availability of part is known. Call complete ; ordrng 1 W11600370 (Ui stainless)"

"Arrived on site to diagnose washer that was not powering on. Tested unit and found it does power on, but just buzzes when you start a cycle. Found failed capacitor causing the failure. Customer said it was also very loud / vibrates a lot when it's spinning. I checked the basket and found a good amount of holes were not punched out, so I'm ordering a new basket and gearcase to resolve the noise and vibration. There's also some coins in the washplate that may be making the noise as well. Office to schedule when we get all needed parts. ; ordrng 1 W11395618 (Capacitor) and 1 W11513243 (Basket) and 1 W11164183 (Gearcase)"

Arrived onsite for leaking determined leak is coming from damaged tub weld. Ordering tub to repair. Office to reschedule. ; ordrng 1 W11409865 (Tub)

"Arrived on site for not dispensing ice. Upon arrival inspected unit and container is full of ice. Customer states that it makes ice, it just does not dispense. Found fc door intermittently does not reach switch. Need to order square spacer. Office to reschedule ; ordrng 1 Wp2177331 (Square)"

"Arrived on site. Removed defective compressor,installed a new compressor and drier,vacuumed system down unit kept vacuum recharged system to manufacture spec powered unit on checked low side pressure good."

Arrived on site to inspect single wall oven. The touchscreen is not working. The touch buttons do work but the touchscreen on the display does not. I tried resetting the breaker and found no change. I found the harness connection good. I am ordering the UI to resolve. Office to order parts and schedule service. ; ordrng 1 W11600370 (UI)

"Arrived on site to diagnose dishwasher not powering on or running. Tested unit and found it unresponsive. Checked voltage at control and found 120 at control. Replaced the control and traced wires to terminal block. Found the neutral wire on the power cord and harness fried, causing the failure. Ordering new power cord and harness to resolve. ; ordrng 1 W11590537 (Wiring Harness) and 1 W11365011 (Power Cord) and 1 W11132441 (Terminal Block) and 1 W11660284 (Console)"

"Arrived on site for not washing. Upon arriving ran diagnostics and got error code F4-E3 wash motor not operating. Inspected unit. Got correct voltage to motor, just not energizing. Need to replace sump and motor. Replaced sump and motor. Test unit and is operating as designed. No leaks present at this time. Job complete"

"Arrived on site to inspect dishwasher error codes. Upon further inspection, I found the unit display showing error code F6E1-no communication with UI. Attempted to clear the code and place in diagnostics, but the control panel failed to respond. I removed the outer door panel and inspected inside the door and found the vent gasket badly crimped allowing steam to enter inside the door and get to the UI causing it to short. I am ordering the vent and gasket and CNOTE-LSO PER CUSTOMER REQUEST and will return with the UI and control panel. Unit left turned off for safety and no water leaks, other than the vent gasket, observed during service.; ordrng 1 W11649995 (Vent) and 1 W11545539 (Gasket) and 1 CNOTE (LSO PER CUSTOMER REQUEST)"

Arrived onsite for failed microwave element support bracket. Replaced support (1). Unit is functioning properly. Job complete

"Arrived onsite for refrigerator with no water or ice production. On inspection the water was working fine, but the ice maker did not pass 2 of the test. It could not home and the thermistor said it was 2 warm, the fc was -2. Gain access to the icemaker and found a small black of ice on top of it. Ordering a icemaker and fill tube heater. No water leaks detected during service. ; ordrng 1 W11577195 (Icemaker) and 1 WPW10554299 (Fill tube heater)"

Arrived on site for washer making a noise. Customer has video of washer making a knocking noise. No error codes stored. Ran diagnostics and found noise during agitate was loud. Removed rotor. Removed cam. No evidence of any oil. Found wear on slider. Replaced slider. Adjusted level. Verified operation. Call complete.

"Arrived on site for a refrigerator. That is not making ice. Inspected unit and work area. The customer advise if the unit does make ice, but it does not make nearly as much rice as it used to. They advise that it is taking the icemaker four days to make recorders in a bin of ice. Check temperatures in the freezer and found temperatures at one degree Fahrenheit. When I had to replace the icemaker assembly and tested the unit. The unit began to work and operate as designed. Call complete."

"Arrived on site , replaced gear case slider and clutch. Ran diagnostics, all checked normal. No water leaks detected at this time. Job complete"

"Arrived on site to test unit for no ice production, tested unit found kinked water line, secured water line properly and tested water is now filling into ice maker, job completed"

"Arrived on site to test unit for no ice production, tested unit found kinked water line, do to water line being kinked for such a long time the water developed a permanent bend, secured water line properly and tested ice maker filled with water properly, stated to maintenance that if ice production stops, replace water line, at this time unit is running as designed, job complete"

"Arrived on site to replace consoleper PR. Replaced console, tested unit, unit is running as intended. No leaks present at this time. Job complete."

Arrived on site to test unit for squealing noise. Found idler was seized. Replaced idler and belt. Unit now working as designed. Job complete.

"Arrived on site to replace right wheel assembly, valve, fill tube heater and potentially housing, attempted to remove unit but unit side trim is behind the cabinet and cant be successfully removed with out heavy scratches to the cabinet and potentially the floor since right side wheel is broken, spoke to customer the in order to get the repair done contractor will need to remove left and right cabinet trim so the unit can be pulled out properly office to follow up with customer and reschedule ; O-emld tckt"

Arrived on site to test unit for not cooling. Unit was unplugged on arrival. Powered unit on and found compressor pulling .8amps. Frost pattern started to develop on evap coils. Applied bubble solution to all potential leak points and found no signs of refrigerant leak. After unit was running about 15mins frost pattern started to seize and would not form beyond first two coils. Recommend replacing compressor and evap for potential restriction in evap. Needing 2hrs on return visit. Office to reschedule. ; ordrng 1 W11547313 (Compressor) and 1 W11572047 (Evap) and 1 W10574478 (Exchanger) and 1 WPW10143759 (UV drier) and 1 W10913906 (Access valve)

Arrived onsite and found new filter would not seat properly due to print from old filter blocking proper engagement. Corrected. Advised customer on repair. All checks good. Unit is now operating as designed.

"Arrived on site to check unit for repeated f8e0 after console replacement. Upon closer inspection found both fans spinning but code f8e0 threw shortly into heating of cavity. Found error code f6e6 indicating appliance manager is faulted. Error code f6e0 indicating the user interface faulted as well. Error code f2e1 indicating shorted key pad as well. Called tech line per notes, tech line stated to replace harness, blower and keypad. Will need to order console. sr7737125349 Office to reschedule ; ordrng 1 W11600643 (Console) and 1 2hourjob (2 hour job) and 1 2manjob (2 man job)"