Service History 86 - Appliance Express

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FPS06

Near Austin, TX 78748

Matthew

Job Details: 10/24/2023

Arrived onsite for unit not leveled. Upon arrival inspected unit. Found unit needed leveling and also the cabinet surround was not leveled. This made the gap between the two exaggerated. Corrected unit and is level. Notified customer that due to cabinet the gap around wil not be even. Job complete

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW3

Near Kyle, TX 78640

Joe Z

Job Details: 10/24/2023

Arrived on site for failed suspension. Upon arrival inspected unit and found defective basket caused suspension to fail. Need to replace suspension and basket. Ordering basket and wash plate and returning with suspension. Office to reschedule ; ordrng 1 W11172199 (Basket) and 1 W10919191 (Washplate)

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT511SZDM02

Near Austin, TX 78752

David Z

Job Details: 10/24/2023

Arrived on date to follow up on refrigerator with locked compressor. Pierced system and found 0 pressure and 0 refrigerant present. I replaced the drier and compressor and vacuumed. Could not get vac. Traced leak to evaporator and also a 1/8' hole in the low pressure side of the evap tubing. I was able to patch the hole and replaced the evaporator. Verified good vacuum. Unit was heavily contaminated and got vacuumed for an extended period of time (found moisture and oil mixed). Charged and tested. Verified cooling and frost pattern starting. Repair completed.

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS03

Near Waco, TX 76712

Jonathan M

Job Details: 10/24/2023

"Arrived on site for a refrigerator that is not making ice. Inspected unit and work area. The customer advised theyve been fiddling with the arm bar and that that has seemingly gotten the thing to work on Acacian but this last time, the unit has not continue to make ice. Didnt find ice in the mold and found proper voltage going to the icemaker. Found temperature in the freezer at 3?F. Replaced the icemaker and immediately found the unit harvesting and feeling as designed. Advise the customer to call back if any other issues persist. Call complete."

We serviced a

WHIRLPOOL MICROWAVE

Model WMH32519HZ07

Near Maxwell, TX 78656

Andrey

Job Details: 10/24/2023

"Arrived on site to test uni5 for control not working, tested unit found unit is working but has cosmetic damage on the door and console, contractor wants this replaced asap do to home is closing, will need to replace door and console on next appointment ordering parts office to reschedule ; ordrng 1 W11173823 (Door)"

We serviced a

KITCHENAID RANGE

Model KSEG700ESS6

Near Waco, TX 76712

Jonathan M

Job Details: 10/24/2023

Arrived on site for an oven that is not heating properly. Inspected unit and work area. The customer advised that the unit did not hear through one of the ready meal cook items that she bought from H-E-B and she believes that the unit is a little under temperature. The customer advised that she had to cook the food for an extra 5 to 10 minutes so she doesnt think its too far off but wanted to have it checked. Ran the unit through a 375?F eight cycle and found the unit cycling between 403?F and 348?F indicating an average temperature of 374.5?F. did explain to the customer that the unit appears to be heating and operating as designed but did show the customer how to calibrate her unit. I did explain that some of those ready meals may have different sizes of chicken and that may have been what caused the issue due to a thicker cut of chicken needing more time. The unit is working as designed. Call complete.

We serviced a

AMANA DRYER

Model NED4655EW1

Near Georgetown, TX 78626

Lou

Job Details: 10/24/2023

"Arrived on site to inspect dryer not heating. Upon further inspection, I tested the unit and found the element not coming on. I tested voltage at the wall and got 245V. Pulled the unit out and removed the back panel and tested the cutoffs, thermostat, fuse, element and timer and found the hi-limit thermostat had shorted due to a loose connector and the timer was not providing voltage. Removed and replaced the thermostat and retested and found the timer continues to not provide voltage. Removed and replaced the timer and retested and unit is operating as designed."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ1

Near Canyon Lake, TX 78132

Andrew

Job Details: 10/24/2023

Arrived on site to test unit for error f8e4(overfill/float switch). Cleared error code and found unit tilting slightly forward. Also found RO system drain tied into dishwasher drain. Leveled unit and advised to have RO drain inserted into drain directly. Ran diagnostics and found no signs of overfilling and no signs of leaking. Advised customer to minimize soap use as unit is supplied soft water to prevent over sudsing. Job complete.

We serviced a

WHIRLPOOL COOKTOP

Model WCG97US0HS00

Near Leander, TX 78641

Maurice R

Job Details: 10/24/2023

Arrived onsite for cooktop flame going out. On inspection this the center burner that goes out when going from high flame to simmer flame. Installed a new dual valve and tested the unit. The unit now is operating as designed and no gas leaks detected during service. W

We serviced a

WHIRLPOOL FREEZER

Model WRT112CZJW00

Near Hewitt, TX 76643

Jonathan M

Job Details: 10/24/2023

Arrived on site for a refrigerator that is not cooling. Inspected unit and work area. The customer explained that the unit started making a really loud buzzing and clicking sound and then the unit completely lost its temperature. He advised that the unit makes the sound every 5 to 10 minutes at this point and will not cool. Found the compressor in touch. Unit will need a new compressor for repair. Ordering all sealed system components and the office will need to contact the customer about a return date due to limited parts availability and need for a two hour service.; ordrng 1 W11370574 (Compressor) and 1 W11559685 (Drip tray) and 1 W11506635 (Access Valve) and 1 WPW10143759 (Drier) and 1 Nitrogen (Nitrogen) and 1 Lokringkit (Lokring kit) and 1 W11504448 (Cap tube to drier coupler)

We serviced a

KITCHENAID REFRIGERATOR

Model KRSC700HPS04

Near San Marcos, TX 78666

Luis

Job Details: 10/24/2023

"Arrived on site. Replaced defective hinge assembly on fresh food side,found unit uneven added shims to right back side adjusted front wheel stop tested door operation good."

We serviced a

WHIRLPOOL WASHER

Model WTW5105HW3

Near Austin, TX 78759

David Z

Job Details: 10/24/2023

Arrived on site to follow up on washer not draining. Replaced harness due to harness repairs not holding. I advised customer if issue repeats I can upgrade the wiring. Unit is working as designed with the new harness. Repair completed.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFSS2625TS0

Near Georgetown, TX 78626

Lou

Job Details: 10/24/2023

"Arrived on site to inspect refrigerator water dispenser not dispensing properly and water flow is slow. Upon further inspection, I tested the dispenser and found the water flowing very slowly and taking too long to fill a cup. I found the filter head was new and the customer has a new filter installed. I found previous tech replaced the filter head and valve. I tested the water pressure at the wall and it was good. I tested the valve and found it bad. I removed and replaced the valve and retested the dispenser and found the unit operating as designed. No water leaks observed during service, job completed."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ10

Near Buda, TX 78610

Luis

Job Details: 10/24/2023

"Arrived on site for cooling complaint. Per customer freezer temp raised to 14 degrees,at time of visit unit cooling correctly ran diagnostics all test passed checked door seals good."

We serviced a

WHIRLPOOL WASHER

Model MVW4505MW0

Near New Braunfels, TX 78132

Andrew

Job Details: 10/24/2023

Arrived on site to test unit for not starting. Found customer was pressing power and start button simultaneously. Cycled power to unit and advised customer to double push required to start unit. Either press start or power to wake unit up and then hold start button till all indicator lights have illuminated then let go. Unit is currently working as designed. No leaks detected. Job complete.

We serviced a

JENN-AIR RANGE

Model JJW2430LL00

Near Spicewood, TX 78669

Leonardo

Job Details: 10/24/2023

Arrived on site to replace left trim. Replaced trim test unit and unit test good job complete.

We serviced a

WHIRLPOOL WASHER

Model wtw4855hw3

Near Manor, TX 78724

Gerald

Job Details: 10/24/2023

WTW4855HW3 arrived on site to install previously diagnosed and ordered parts. Removed and replaced the suspension rods and wash basket. Ran a calibration cycle. No water leaks observed during service.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS2

Near Round Rock, TX 78665

Blake

Job Details: 10/24/2023

Arrived on site to install previously diagnosed and ordered parts. I removed and replaced the inlet valve and the flow meter and tested. The unit now operates as designed. No leaks observed during service.

We serviced a

KITCHENAID DISHWASHER

Model KDTM704KPS1

Near Austin, TX 78723

Gerald

Job Details: 10/24/2023

KDTM704KPS1 arrived on site to inspect a leaky dishwasher. Upon inspection I noticed water leaking from the back of the unit. Pulled the unit out and ran a diagnostic cycle and found water leaking from a dented seam at the top of the unit (see photo). Showed my findings to the customer. Ordering the tub for R/S. Office to contact customer when part arrives. ; ordrng 1 W11409866 (Tub)

We serviced a

WHIRLPOOL REFRIGERATOR

Model ASI2575GRS08

Near Temple, TX 76504

Sterling

Job Details: 10/24/2023

On arrival verified complaint of no ice. Found twist tray ice maker stuck mid harvest and unable to reset. Verified correct voltage to ice maker. Ordering W11546935 ice maker. Rescheduled for 11/7 per customer schedule. Return with icemaker and water valve for repair and further testing. ; ordrng 1 W11546935 (Ice maker twist tray)

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ1

Near Leander, TX 78641

Maurice R

Job Details: 10/24/2023

"Arrived onsite for dishwasher handle loose. On interior the nut was loose, tightened the not up reinstall the handle and it is working as designed. No water leaks detected during service."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Tow, TX 78672

Miguel

Job Details: 10/24/2023

"Arrived on site for refrigerator not dispensing ice and making a loud noise, removed back panel. Found noise went away. Adjusted tubing away from cover. Removed and replaced auger motor and shaft. Verified operation. Call complete."

We serviced a

WHIRLPOOL REFRIGERATOR

Model wrt541szdm01

Near Hutto, TX 78634

Blake

Job Details: 10/24/2023

Arrived on site to install door gasket. I removed and replaced the door gasket and heated with my heat gun. The unit now operates as designed. No leaks observed during service.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF736SDAM14

Near Harker Heights, TX 76548

Sterling

Job Details: 10/24/2023

On arrival verified complaint of FC freezing. Found FC gasket is falling off the door. Will not seal or seat into place. FC door liner is too loose. Will require an FC door with gasket. As well as full defrost of FC section as evap is freezing up due to increased hot air in system. Ordering FC door LW10422791 office to reschedule ; ordrng 1 LW10422791 (FC door)

We serviced a

WHIRLPOOL MICROWAVE

Model WMH31017HS09

Near Kyle, TX 78640

Joe Z

Job Details: 10/24/2023

Arrived on site for light does not turn off. Upon arrival inspected unit. Found relay is stuck on closed position. Need to replace control. Replaced control W11552018. Test unit and is operating as designed. Job complete

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF757SDHZ04

Near Austin, TX 78757

David Z

Job Details: 10/24/2023

Arrived on site to diagnose refrigerator making noise when doors are opened/closed. Had customer confirm the noise when u was there. I identified the noise as ramping fans and compressor. Noise was not abnormal in volume and is working as designed. Asvised customer this noise is normal and within spec and consistent with other units.

We serviced a

GE RANGE

Model PGS960SEL2SS

Near Cedar Park, TX 78613

Maurice R

Job Details: 10/24/2023

Arrived onsite for gas leak in range. Customer had plumper go through the gas connections to make sure that there is no gas in the house. I tried to remove the bottom bake cover and could not get it off. Turn the unit on to bake at 350? for 20 minutes and could not smell any gas form the range. I informed the customer that we will get a technician that has worked on this unit. No gas leak detected during service.; saved tckt

We serviced a

WHIRLPOOL DISHWASHER

Model WDF331PAMS0

Near Liberty Hill, TX 78642

Miguel

Job Details: 10/24/2023

"Arrived on site for dishes not drying, ran diagnostics and found no error codes. Water fills. Wash pump working. Heater pulls 7 amps. Water drains. All components check ok. Found rinse aid empty. Advised customer of drying procedure. Call complete. Techline sr#7737625449"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS09

Near San Marcos, TX 78666

Luis

Job Details: 10/24/2023

"Arrived on site for moisture issue. Checked mullion,removed mullion secured harness reinstalled mullion ran diagnostics on unit,unit working as designed."

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Troy, TX 76579

Sterling

Job Details: 10/24/2023

Customer complaint is washer tub disconnected from the frame. Found no evidence of disconnect. Customer states reason for thinking it was on the ground when loaded up with clothes. Replaced suspensions due to some excess shaking and advised if problem persists customer may be overloading unit. Spoke with customer on proper use and care and they were loading unit incorrectly. Instructed on proper loading. Operational test good. No leaks detected during service. Job complete

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHZ02

Near Leander, TX 78641

Maurice R

Job Details: 10/24/2023

Arrived onsite for refrigerator not dispensing water. On inspection there was very little ice and no water would dispense. Gain access to the back of the unit and found that the valve would only mist water. Installed new valve and now the water is being dispense as a designed. No water leaks detected during service. Talked with Melissa about warranty and payment.

We serviced a

WHIRLPOOL DRYER

Model WED4850HW0

Near Austin, TX 78758

Wesley

Job Details: 10/24/2023

Arrived onsite and repaired unit with failed door switch by replacing door switch. Unit is now operating as designed. All checks good.

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW3

Near Austin, TX 78758

Wesley

Job Details: 10/24/2023

Arrived onsite for not agitating. Found actuator lost position. Replaced actuator. Unit is now operating as designed. All checks good.

We serviced a

WHIRLPOOL DRYER

Model WED4815EW1

Near Dripping Springs, TX 78620

Matthew

Job Details: 10/24/2023

"Arrived on site for unit, making a scraping noise. Upon arrival inspected unit and found part of the felt had pulled back allowing metal to metal contact on the drum. Replace the drum. Insured the drum seal was good. Tested and unit is no longer making noise. Job complete"

We serviced a

WHIRLPOOL FREEZER

Model KBSD708MPS00

Near Bertram, TX 78605

Miguel

Job Details: 10/24/2023

Arrived on site with new icemaker. Replaced Icemaker. Verified assembly. Call complete.

We serviced a

MAYTAG WASHER

Model MVW6500MBK0

Near Round Rock, TX 78681

Paul

Job Details: 10/24/2023

Arrived onsite for a washer that will fill with water then start to agitate and just stop with the tub full of water. I checked stored error codes and had an F7E1 tachometer signal missing & F0E9 off balance pause. I tested the tachometer circuit and could not find anything wrong. I replaced the control and the actuator. I spoke with the customer and he stated he never opened the door at anytime during the load. He just turned the unit off and it would drain. I tested the unit in a wash cycle and found it staying on sensing and the door not locking. I found the door switch circuit open from the control with the lid shut. I replaced the door latch. I ran a load of towels on the towel setting and tested the washer. The washer is working as designed. There were no water leaks present at the time of service. Call complete.

We serviced a

WHIRLPOOL RANGE

Model WFG505M0MS0

Near Andice, TX 78628

Maurice R

Job Details: 10/24/2023

"Arrived onsite for previously diagnosed parts. Installed new screws into the Handel, the door is operating as designed and no gas leaks detected during service."

We serviced a

KITCHENAID DISHWASHER

Model KDFE104KPS0

Near Manor, TX 78653

Kimo

Job Details: 10/24/2023

Arrived onsite for a DW that is leaking. Upon inspection I found water in the drip pan and signs of leaking coming from the the tub gasket. You can see there the soap and water left streaks on the door where it got pats the gasket. I found that the dispensary had a leak and am ordering one to replace it. I did find that the unit had a lot of detergent residue left behind on the gaskets door as. Even on the inner skin of the door. Signs of a over suds issue I did advise the customer on detergent sue and set the return date 10/30/23; ordrng 1 W11412300 (DISPENSER)

We serviced a

WHIRLPOOL RANGE

Model WFE975H0HZ2

Near Taylor, TX 76574

Blake

Job Details: 10/24/2023

Arrived on site to inspect range. The customer states the LF element is cycling off too much causing them to not be able to boil water or cook properly. I found the LF element heating properly and cycling. I was unable to recreate the issue. I am ordering the LF element to resolve. Office to order parts and schedule service. ; ordrng 1 W11563195 (LF element)

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF707ESS01

Near New Braunfels, TX 78132

Luis

Job Details: 10/24/2023

"Arrived on site. Diagnosed a defective led,replaced all leds with led kit."

We serviced a

KITCHENAID REFRIGERATOR

Model KRSF705HPS05

Near Austin, TX 78730

David Z

Job Details: 10/24/2023

Arrived on site to install new refrigerator door due to damage. Replaced new door and verified proper function. Repair completed.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAHZ0

Near Austin, TX 78717

Paul

Job Details: 10/24/2023

Arrived onsite for a dishwasher not heating or drying the dishes. I ran diagnostics and there were no stored error codes. I ran the machine and found it working as designed. I found the heater drawing 7.40 amps in the wash cycle and starting out the same in the drying cycle. I went over detergent use and rinse aid use with the customer and how to watch for suds and how to listen to the pump motor for cavitation. I showed him that the rinse aid was turned up to high and showed him the suds in the machine. I turned the rinse aid down to the minimum setting. I explained to run the hot water at the faucet and get it as hot as possible before starting the machine. I explained how to properly use a dishwasher cleaner in the machine. This machine is working as designed at this time. There were no water leaks present at the time of service. Call complete.

We serviced a

WHIRLPOOL ICE MACHINE

Model KUID508HPS00

Near Austin, TX 78730

David Z

Job Details: 10/24/2023

Arrived on site to diagnose icemaker overproducing ice. Found failed bin thermistor reading that bin was not full. Replaced and verified bin reading properly. Repair completed.

We serviced a

WHIRLPOOL MICROWAVE

Model WMH32519HZ10

Near Hutto, TX 78634

Blake

Job Details: 10/24/2023

Arrived on site to inspect OTR microwave. I tested all functions of the microwave and found no issues. I found no stored error codes. The unit is operating as designed at this time.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT318FZDB09

Near Austin, TX 78744

Joe Z

Job Details: 10/24/2023

Arrived on site for hanging FC gasket. Upon arrival inspected Fc door and gasket. Found gasket is not inserted into liner correctly. Reattached gasket. Door liner is not able to stay secure. The liner is to wide of a gap. Need to replace door

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SWHZ00

Near New Braunfels, TX 78130

Luis

Job Details: 10/24/2023

"Arrived on site for cooling complaint. Per customer unit stopped cooling then on its own it started operating correctly. Diagnosed a defective control,replaced control ran diagnostics all test passed."

We serviced a

MAYTAG DRYER

Model MED7230HW3

Near Temple, TX 76502

Sterling

Job Details: 10/24/2023

"On arrival verified complaint of no heat. Checked voltage and polarity is correct at plug found 240, 120, 120. Started test cycle found no heat. Checked heater, and thermostats. All checked good. Checked voltage at heater and found 120. Checked voltage at heater relay found 120 vac output to heater. This indicates failed centrifugal switch as the motor runs during cycle. Tech to replace motor. Bring harness just in case. Ordering motor W11549461 and harness main W11556656. Resched for 11/2; ordrng 1 W11549461 (Motor) and 1 W11556656 (Main harness)"

We serviced a

WHIRLPOOL RANGE

Model WFG505M0BS3

Near Waco, TX 76704

Jonathan M

Job Details: 10/24/2023

Don site for an oven that is not heating. Inspected unit and work area. Customer advised the unit was working really well until they went to make some pizza the other day and the unit would not heat. Tested the unit and found the glow bar would not ignite despite voltage going to it. Replaced the oven igniter and tested the unit. The unit began to work and operate as designed. Call complete.

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Taylor, TX 76574

Blake

Job Details: 10/24/2023

"Arrived on site to inspect top load washer noise. The customer informed me the unit makes a loud noise during fill and while spinning. It is spinning unbalanced as well. I found the cam teeth sheered off. I installed a cam from truck stock and retested. I heard no valve noise but could still hear a screeching sound from the gearcase. I am ordering the gearcase, cam, actuator, capacitor, belt, and valve to resolve. No leaks observed during service. ; ordrng 1 W11449840 (Gearcase) and 1 W10721967 (Cam) and 1 W11481722 (Actuator) and 1 W11395618 (Cap) and 1 W11239857 (Belt) and 1 W11513255 (Valve)"

We serviced a

WHIRLPOOL RANGE

Model WFG320M0MS0

Near Manor, TX 78653

Kimo

Job Details: 10/24/2023

Arrived onsite for a range that would not heat in the oven. Upon inspection I found that the bake burner found not ignite all the way. I adjusted the burner and got it to ignite properly and tested the unit and found that it ignites fully every time and the unit heated as well

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ09

Near Belton, TX 76513

Sterling

Job Details: 10/24/2023

On arrival verified complaint of over cooling. Unit is set to 45 RC but internal temps are 38. If temp set correctly unit will freeze over. Found damper section for ice maker is suck open. Will not stop air flow. Spoke with TJ at TL 7737495900 advised to replace the damper assy. Ordering and reschedule for 10/30. ; ordrng 1 WPW10196393 (Damper motor)

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ0

Near Harker Heights, TX 76548

Sterling

Job Details: 10/24/2023

On arrival verified complaint of no wash motor. Replaced wash motor and ran operational test. All test good. Job complete no leaks detected during service.

We serviced a

MAYTAG WASHER

Model MVWB765FC3

Near China Spring, TX 76633

Jonathan M

Job Details: 10/24/2023

"Arrived on site for a washing machine that is flashing an F60 error code. Inspected unit and work area. Around the entry diagnostics and found an F0 E5 (off balance load), F0 E3 (overload), and F2 E1 (UI stuck key) barcodes. The customer showed me a video of what happened and I could see an OFB error message appear. They advised that they saw the unit was going off balance, and removed all clothes. They said that even with just a tub full of water that the unit was going off balance. Around the unit through a spin cycle and could hear evidence of some grinding going on underneath. removed the rotor and found the slider, broken and grinding against the clutch. Replaced the slider with a truck stock slider and tested the unit. The unit began to work and operate as designed. Call complete.; used 1 W10734521 (Slider) from stock"

We serviced a

WHIRLPOOL WASHER

Model WETLV27HW3

Near Georgetown, TX 78628

Lou

Job Details: 10/24/2023

"Arrived on site to inspect washer not completing cycles. Upon further inspection, I found the wash LED lit up on the control panel. I placed the unit in diagnostics showing error code F8E1 & F2E1. Cleared the codes and continued with testing. The unit operated as designed. Per code F8Eq-long fill/no fill, I manually tested the valves and they continue to operate as designed. Due to the F2E1-stuck key code, I removed and replaced the main control and when I disassembled the panel, I found the water level sensor tube not connected to the control (photo). Once I had the control replaced, I calibrated the unit and retested and the unit operates as designed. No water leaks observed during service, job completed."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS05

Near San Marcos, TX 78666

Luis

Job Details: 10/24/2023

"Arrived on site for cooling issue. Per customer unit stopped cooling customer had to power cycle unit and unit started cooling again,unit cooling correctly at time of visit. Ordering main control and ui; ordrng 1 W11577100 (Ui control) and 1 WPW10675033 (Main control)"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ1

Near Georgetown, TX 78628

Maurice R

Job Details: 10/24/2023

Arrived onsite for dishwasher rack broken. On inspection found the top rack would not pull out. On further inspection found that the back wheel on the left side was out of the track. Removed the rack and reinstalled the wheel in to the rail.the rack is working as designed now. No water detected during service

We serviced a

WHIRLPOOL COOKTOP

Model WCG55US6HS00

Near New Braunfels, TX 78130

Andrew

Job Details: 10/24/2023

Arrived on site to test unit for loose knobs and unable to properly adjust flames. Found valve was cracked to LR burner. Replaced manifold and unit now working as designed. Applied bubble solution and found no leaks. Verified now working as designed. Job complete.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHW06

Near Belton, TX 76513

Tyler

Job Details: 10/24/2023

"Arrived on site for refrigerator needing previously diagnosed fill tube, clamps, and slide. Upon arrival installed parts then tested ice maker found no leaks and unit working as designed. Call complete"

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW3

Near Manor, TX 78724

Gerald

Job Details: 10/24/2023

WTW4855HW3 arrived on site to inspect washing machine not working. Checked for voltage at the wall and discovered that there was none. Checked the breaker and found it tripped. Cycled the breaker and tested the GFCI and it failed. Informed the customer of my findings and informed maintenance.

We serviced a

WHIRLPOOL DISHWASHER

Model WDF331PAHS1

Near Jarrell, TX 76537

Blake

Job Details: 10/24/2023

Arrived on site to inspect dishwasher not running. I found error code F4E3 and F7E1. I tested and found the pump open. I removed and replaced the motor assembly and tested. The unit now operates as designed. No leaks observed during service.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS555SIHZ00

Near Hutto, TX 78634

Blake

Job Details: 10/24/2023

Arrived on site to inspect ice maker not making ice. I found the fill tube frozen once again. I removed and replaced the FC door to resolve. The unit now operates as designed. No leaks observed during service.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ08

Near Pflugerville, TX 78660

Gerald

Job Details: 10/24/2023

WRS321SDHZ08 arrived on site to install previously diagnosed and ordered parts. Removed and replaced the ice container and the customer said that in the on position the ice maker was still not producing ice. Tested the unit and the ice maker would not harvest or fill. Replaced the ice maker and tested and the unit passed with no water leaks observed during service.

We serviced a

KITCHENAID DISHWASHER

Model KDFE204KPS1

Near Austin, TX 78758

Wesley

Job Details: 10/24/2023

Arrived onsite and found unit with lower wash arm failure. Ordering lower wash arm to repair. Stacking Thursday to return and repair because call will not take a full time slot. ; ordrng 1 W11550888 (Wash arm)

We serviced a

KITCHENAID MICROWAVE

Model KOCE500ESS22

Near Georgetown, TX 78633

Lou

Job Details: 10/24/2023

"Arrived on site to inspect wall oven microwave combo unit with the microwave element support broken. Upon further inspection, I found the microwave element hanging down and the support missing. I pulled the unit out and disassembled and installed a new support and reassembled the unit. Tested and unit is operating as designed. Job completed. No one available to sign for the receipt."

We serviced a

KITCHENAID DISHWASHER

Model KDFE204KPS0

Near Seguin, TX 78155

Andrey

Job Details: 10/24/2023

"Arrived on site to test unit for beeping noise, tested unit found control not allowing me into diagnostics and activating erratic, replaced control and tested, dishwasher drain connections to sink is extremely loose and may pop out and flood the kitchen, attempted to tighten but its still loose because the sink connection is only 1/2 inch and needs to be 3/4, advised customer to get someone to fix this issue, unit is now running as designed, no leaks detected job complete"

We serviced a

WHIRLPOOL MICROWAVE

Model WMH32519HZ07

Near Jarrell, TX 76537

Blake

Job Details: 10/24/2023

Arrived on site to inspect OTR microwave fan noise. I inspected the fan and found something rubbing the blades. I removed the restriction and tested. The fan now sounds normal. The damper was bent. I removed and replaced the damper from truck stock(W10843943). The unit now operates as designed.

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near New Braunfels, TX 78132

Andrew

Job Details: 10/24/2023

Arrived on site to test unit for grinding noise. Found rotor retention bolt was missing. Replaced slider as a precautionary and secured bolt with blue locktite. Unit working as designed. No leaks detected. Job complete.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT311FZDW02

Near Georgetown, TX 78628

Lou

Job Details: 10/24/2023

"Arrived on site to install previously diagnosed and ordered parts. Upon arrival, I began to evacuate the system and found no refrigerant in the system. I isolated the exchanger and evaporator and heat loop and found no leaks. Using my black light, I searched for an6 signs of dye leaking from the evaporator and found nothing. I checked at the compressor area and found dye under the compressor and spray marks on the access valve. I removed and replaced the compressor, access valve and UV dye drier and vacuumed the system. Pressures held good at -30/0. I installed 47g of R600 refrigerant and plugged the unit in and monitored the unit. I found a good frost pattern on the evaporator and the unit is beginning to cool. I recommended the customer monitor the unit for approximately 24 hours before placing items inside. No water connections to the unit/no leaks observed during service, job completed."

We serviced a

JENN-AIR FREEZER

Model JBZFL30IGX10

Near Lakeway, TX 78738

Matthew

Job Details: 10/24/2023

"Arrived onsite for unit not making ice again. Upon arrival checked temperature. Recorded 6 degrees before unit went into defrost. Ran Test 16 ice maker thermostat reads 32 degrees then 5 degrees. Ran Ice maker test 120, went from 01 to 04 then E2. Tried again and 1-4 did not complete full cycle then BF on display. Called tech line for assistance. Spoke to Bruce SR#7737625331. Tech determined the ice maker is bad. Reordering ice maker assembly. Office to reschedule ; ordrng 1 W11646196 (Ice maker)"

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Taylor, TX 76574

Blake

Job Details: 10/24/2023

Arrived on site to inspect top load washer noise. I found the belt slipping and also damage to the cam. I removed and replaced the cam and belt and tested. The unit now operates as designed. No leaks observed during service.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT318FZDM06

Near Bertram, TX 78605

Miguel

Job Details: 10/24/2023

Arrived on site for refrigerator not cooling. Found refrigerator and freezer only slightly cooler than room temp fan is working. Removed back panel and confirmed condenser fan and compressor running. Pulls 0.46 amps. Removed evaporator cover. Confirmed no frost pattern. Will need sealed system repair. R134a with aluminum cap. 162.36 Auth code: 949C3J; ordrng 1 Lokring (Lokring) and 1 Nitrogen (Nitrogen) and 1 W11480426 (Compressor) and 1 W11480426 (Coupler) and 1 WPW10143759 (Drier) and 1 W11407409 (Evaporator)

We serviced a

KITCHENAID OVEN

Model KOSE500ESS20

Near Briarcliff, TX 78669

Leonardo

Job Details: 10/24/2023

Arrived on site to test unit for oven heating to fast. Test unit and found unit pre heated to 350? with in 15 minutes perfect time. Unit maintained average temp of. 356? when set at 350?. Unit test good job complete.

We serviced a

WHIRLPOOL OVEN

Model WOD51EC0HS02

Near Canyon Lake, TX 78132

Andrew

Job Details: 10/24/2023

Arrived on site and replaced previously diagnosed lower oven TOD. Tested both top and bottom oven to 350 with no issues. Unit currently working as designed. Job complete.

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near San Marcos, TX 78666

Joe Z

Job Details: 10/24/2023

"Arrived on site for making noise, upon arrival, ran diagnostics and there are no saved error codes. Ran a spin cycle and can hear squeaking from belt. Inspected belt and found worn and frayed. Need to replace belt. Replaced belt W11239857 from truck stock. Test unit and is operating as designed. No leaks present at this time. Job complete"

We serviced a

WHIRLPOOL COOKTOP

Model WCG97US6HS00

Near New Braunfels, TX 78130

Andrew

Job Details: 10/24/2023

Arrived on site to test unit for gas leak. Applied bubble solution to connections and found no signs of leak. Customer stated smell happened when RF burner was in use. Was unable to replicate issue. Advised customer to ensure burner caps are always on properly to ensure even distribution of fuel. SR#7737425784

We serviced a

MAYTAG WASHER

Model MVW7232HW0

Near Harker Heights, TX 76548

Tyler

Job Details: 10/24/2023

Arrived on site for washer needing previously diagnosed inner basket. Upon arrival reconfirmed failure and installed part. Found no leaks and unit working as designed call complete

We serviced a

KITCHENAID OVEN

Model KODE500ESS20

Near Austin, TX 78748

Leonardo

Job Details: 10/24/2023

"Arrived on site to test unit for front door glass broken. Found broken glass, went to replace front door glass and found we had the wrong model. We had wrong door. Ordering new front door office to reschedule ; ordrng 1 W11600222 (Front door glass)"

We serviced a

WHIRLPOOL OVEN

Model KFGC506JSS00

Near Austin, TX 78745

Leonardo

Job Details: 10/24/2023

Arrived on site to test unit for unit not getting to pre heated temp. They reset the breaker and the unit works correctly. Will need to replace the control board and appliance manager. Also found door not closing correctly will need to order new left hinge and right hinge. Ordering new MPC board office to reschedule ; ordrng 1 W11394663 (Control board) and 1 W11568941 (Left hinge) and 1 W11568813 (Right hinge)

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF606ESS01

Near Elgin, TX 78621

Kimo

Job Details: 10/24/2023

"Arrived onsite for a refrigerator that is not cooling upon arrival I found 58* in RC. 5*in fc. Upon further inspection I found water in the pantry ui. And the RC evap frozen over. I also found that the RC door gasket torn. I am ordering the drain pan it may be downed due to icing, damper due to icing the ice may have damaged it. Wire harness due to the RC fan not running, drain tube and adhesive to help seal up the drain hole from air seeping in at the back of the unit. I am also ordering the gasket as it is torn and leaking warm air in to the unit. And returning with all controls to replace the water found in the pantry Ui may have caused some damage to the other controls in the unit. I rescheduled the customer for 11/02/23 ; ordrng 1 W11457241 (PAN-DRIP) and 1 WPW10248595 (Damper) and 1 W11087438 (HARNS-WIRE) and 1 W10846057 (GASKET-FIP) and 1 W11661573 (Drain tube EXTENSION) and 1 W10841140 (ADHESIVE)"

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Leander, TX 78641

Maurice R

Job Details: 10/24/2023

Arrived onsite for dishwasher leaking. On inspection found drain hose had a leak in it. Installed new drain hose and tested the unit. No more leaks detected during service.

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Elgin, TX 78621

Kimo

Job Details: 10/24/2023

Arrived onsite for a washer the is leaking from the cold water inlet valve upon arrival I found this to be true I replaced the water valve/drawer. And tested the unit and found unit operating as designed. No leaks.

We serviced a

AMANA DRYER

Model NED4655EW

Near Austin, TX 78744

Joe Z

Job Details: 10/24/2023

"Arrived on site to install previously ordered parts. Upon arrival, customer states that he does not need service and says everything has been fine since last visit"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ15

Near San Marcos, TX 78666

Luis

Job Details: 10/24/2023

Arrived on site for noise complaint. Per 1 customer sounds like a shotgun noise per husband tapping noise. Ran multiple test through diagnostics no odd noises from functioning parts. Advised customer to call customer service if set for a return visit follow service pointer W10266810

We serviced a

JENN-AIR ICE MACHINE

Model JUIFX15HX00

Near New Braunfels, TX 78130

Luis

Job Details: 10/24/2023

"Arrived on site for little and to no ice. Ran diagnostics weak to no water flow,removed filter better flow however still weak replaced the defective water valve,ran diagnostics good water flow. Customer will need to replace the filter"

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Seguin, TX 78155

Andrey

Job Details: 10/24/2023

"Arrived on site to test unit for water leak, customer stated that its not leaking but condensation is developing on the top of counter top, inspected and found that unit does have the insulation wrap, advised customer to buy a 1/4 inch insulation and glue it the bottom of the countertop so heat from the dishwasher will not heat up the countertop, unit is running as designed, no leaks detected job complete"

We serviced a

WHIRLPOOL DRYER

Model WED5100HW2

Near Copperas Cove, TX 76522

Tyler

Job Details: 10/24/2023

"Arrived on site for dryer tripping breaker. Upon arrival was only able to get unit to trip once and bulk/normal cycle. Ran unit on other cycles for over 40 minutes but couldnt replicate issue further, customer opted to see if issue reoccurs. Call complete"

We serviced a

WHIRLPOOL DRYER

Model WED4850HW0

Near San Marcos, TX 78666

Andrey

Job Details: 10/24/2023

"Arrived on site to test unit for no power, tested unit found unit is running but not heating, found shorted thermal cutoffs, replaced cutoffs W10900067 from truck stock, tested, unit is now running as designed, job complete"

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS1

Near San Marcos, TX 78666

Joe Z

Job Details: 10/24/2023

Arrived on site for not operating. Upon arrival got error code F7-E2 variable speed wash motor failure . Replaced sump and motor and same issue. Ran normal operation and unit not filling. Replaced fill valve and there is no change. Replaced control and there is no change. Contacted service management. Recommend ordering harness as well aswith float switch and flow meter switch ( flow assembly). Office to reschedule ; ordrng 1 W11535094 (Inlet water assembly) and 1 W11545764 (Float switch) and 1 W11677715 (Harness)

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Waco, TX 76708

Jonathan M

Job Details: 10/24/2023

Arrived on site for a wash machine. That will not lock the lid. Inspected unit and work area. Found the unit attempting to lock the lid but would just try over and over again without doing so prior to starting a cycle. Did confirm the customer complaint and replaced the latch assembly. tested the unit and the unit began to work and operate as designed. Call complete.

We serviced a

WHIRLPOOL COOKTOP

Model KCGC506JSS00

Near Meridian, TX 76665

Jonathan M

Job Details: 10/24/2023

Arrived on site for a cooktop that is slow to ignite on the left front burner. Inspected unit and work area. Found the unit taking 10 to 15 clicks before turning on the left front burner. When ahead and replaced the burner head and tested the unit. The unit began to work and operate as designed. Call complete.

We serviced a

WHIRLPOOL MICROWAVE

Model WMH31017HS09

Near Austin, TX 78728

Paul

Job Details: 10/24/2023

Arrived onsite for a microwave that has no power but there is power at the outlet. I found the cavity thermostat open and it will need to be replace. Ordering W11224856 cavity thermostat. RS for Mon 10/30.; ordrng 1 W11224856 (Cavity thermostat)

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KPS1

Near Austin, TX 78717

Paul

Job Details: 10/24/2023

Arrived onsite for a dishwasher to replace the previous diagnosed parts. I replaced the console and tested the functions. All are working as designed. Call complete.

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW2

Near Elgin, TX 78621

Kimo

Job Details: 10/24/2023

Arrived onsite to install previously diagnosed part. Upon arrival I installed the back and tested the unit and found that the unit is operating as designed.

We serviced a

WHIRLPOOL WASHER

Model MVWC565FW1

Near Austin, TX 78753

Wesley

Job Details: 10/23/2023

Arrived onsite and found unit operating with failed suspension. Replaced the suspension. Unit is now operating as designed. All checks good.

We serviced a

WHIRLPOOL DRYER

Model WED4950HW0

Near Austin, TX 78719

Joe Z

Job Details: 10/23/2023

Arrived on site for not turning on. Upon arrival unit is not plugged in. Restored power to supply. Test polarity and is correct. Test unit and is operating correctly. Cannot duplicate the unit. Job complete

We serviced a

WHIRLPOOL OVEN

Model KFGG504KPS3

Near Marble Falls, TX 78654

Gerry C

Job Details: 10/23/2023

"KFGG504KPS3 Arrived to inspect oven light not shutting off. I found the actuator rod had popped out of its thru-hole and corrected. During service, I noted the faint odor of LPG. I checked all connections within the unit and found no signs of leaks. The wall behind the unit had an entry point and gas could be detected at that point. On the other side of the wall, the unit was connected to a refillable LPG/regulator system and gas odor was detected at the penetration point as well. I suspect the supply line has a pinhole leak and I shut the gas to the unit off and advised the customer of the repair and my findings of the gas leak."

We serviced a

KITCHENAID COOKTOP

Model KCIG556JSS01

Near Austin, TX 78739

Scott

Job Details: 10/23/2023

"Arrived on site for center burner not working on cooktop. Did power reset and set correct model number . Ran heat test , pot is heating up now . Job complete"

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS1

Near Austin, TX 78731

Kimo

Job Details: 10/23/2023

Arrived onsite for a DW with a top ran that is falling down. Upon inspection I found that the right hand side of the deck was falling off. I replaced both adjusters and tested the unit and found the unit operating as designed.

We serviced a

WHIRLPOOL RANGE

Model WFG505M0BS3

Near Leander, TX 78641

David Z

Job Details: 10/23/2023

"Arrived on site to diagnose range with broken door. On arrival customer had said the handle screw had come out, and door slammed when handle got loose and resulted in outer glass shattering. Confirmed only needed part is the outer glass. Called ext warranty to request autho due to nature of damage. Was informed to close out ticket and customer will have follow up from ext warranty. Call complete."

We serviced a

WHIRLPOOL RANGE

Model WFG505M0MS0

Near Austin, TX 78747

Matthew

Job Details: 10/23/2023

Arrived onsite for gas smell. Inspected and tested unit. Found no indication of a gas leak. Inspected ignition process and flam burn and unit is functioning properly. Inspected during cycling and valve is shutting off properly. House is in a new subdivision with construction throughout and customer may experience occasional burning off of debris while other homes are being tied in. Customer may be experiencing the gas additive smell but unit does not have a leak. Job complete