"Unit 2230Arrived on site for no cool. Unit powered off,powered unit on compressor powered on removed evaporator cover frost forming on evaporator,checked harness connections good checked heater good. Ran diagnostics all test passed."

"Arrived on site for dryer not starting. Upon arrival confirme failure, found door switch broken leading to failure. Bypassed switch and found unit could work. Ordering WPW10237959 door switch to complete repairs. Rescheduled customer for 12/8/23; ordrng 1 WPW10237959 (Door switch)"

Arrived onsite for not spinning and found cam cracked causing failure to spin. Ordering cam to repair. Office to reschedule. ; ordrng 1 W10721967 (Cam)

Arrived onsite and tested unit for having not finished a preheat properly. Reset control and tested all functions. Temps are accurate and preheating as designed. Advised customer on findings. How to reset the control and to watch for proper door closure because a door that is not fully closed will prevent preheat due to the door switch not being engaged. All checks good.

"Arrived on site for damaged door panel . On arrival unit was uninstalled due to floor work, took pic. Replace panel. Job complete"

Arrived on site opened new console found damaged console. We will need to re prefer new console office to reschedule ; ordrng 1 W11624798 (Console)

KUIX535HPS01 Arrived to install previously diagnosed and ordered parts. I removed and replaced the faulty cutter grid and circulation pump/level sensor and tested. The unit resumed all normal functions and operated as designed. No leaks observed during service.

Arrived on site for range where inner liner of oven was warping. Upon arrival confirmed issue and found inner liner flooring of oven was warping upwards in front right corner. Called techline and reported findings Sr#7737939046. Techline stated that warping in lower liner is normal and expected to happen. Stated nothing can be done to adjust liner. Reported findings to customer per Techline recommendation. Unit works as designed call complete

Arrived onsite for previously diagnosed parts. Installed the UI and tested the unit with a cup of water. Before the new ui you could not heat a cup of water for 2 minutes because the screen would blank out. After the new ui we heated 3 cups of water up and had the oven heating up to 350?. The ui never went blank!! The unit is operating as designed.

"Arrived on site to inspect unit for clean light flashing. Upon closer inspection found error code f8e4, f9e2. Dried out float switch and cleared error codes, unit now running as intended. Recommended to customer to use liquid soap and not pods due to being on rain water system to help with over sudsing. Job complete."

Arrived on site to insect gas range error code. I found error code F3E0. I tested the sensor and found it open. I removed and replaced the oven sensor and tested. The unit now operates as designed. No gas leaks detected during service.

"Arrived on site for different components turning on and off by themselves and door. Remains locked. Upon arrival, power cycled unit and door remains locked. Found latch motor has seized. Need to replace latch and control . Replaced latch W11598123 and control W11649136. Test unit by preheating oven to 350. Unit is now operating as designed. Job complete"

Arrived on site to inspect dryer. I found the dryer heating and cycling properly. I found poor airflow while the unit is running. I removed the vent hose and found good flow from the dryer. The house vent is clogged. I instructed the customer to get their vent checked before using the unit further. No gas leaks detected during service.

Arrived on site for washer now working. Making a loud noise. Confirmed noise is coming from coupler. Found motor was damaged as well. Replaced motor and coupler. Verified operation. Call complete.

Arrived on site for washer making a loud grinding noise. Upon arrival confirmed issue. Found no errors in diagnostics but didntraced sound to rotor screw coming loose from gearcase and not allowing slider to activate properly. Replaced slider and screw from slider kit and found noise no longer present call complete

"Arrived on site for noise complaint and level complaint. Replaced front left level leg and axle. Replace motor, fan scroll, retainer and harness. Verified operation. Call complete."

"Arrived on site to install previously ordered parts. Replaced tub assembly W11460604, all 4 shock absorbers W11316766, stator W113554541, rotor W11314361, and bolt W11557803. Test unit and is spinning correctly without any abnormal sounds. Unit is operating as designed No leaks present at this time. Job com"

Arrived on site as helper to JZ for tub replacement. Job completed

"Arrived on site to test unit for spray arm issue, tested unit found spray arm popped off and melted on the heater, replaced spray arm and tested, unit is now running as designed, no leaks detected job complete"

Arrived on site to install previously diagnosed and ordered parts. I removed and replaced the Ui control. I ran a diagnostic cycle to calibrate. I then ran a normal cycle and found the unit now operates as designed. No leaks observed during service

"Arrived on site to replace UI due to control not fixing all present items on previous trip. Was able to put unit into diagnostics this trip and ran through diagnostics cycles, unit is running as designed. Job complete."

Arrived on site to diagnose icemaker not making ice. Tested unit and found icemaker stuck in harvest location but will not return home. Replaced icemaker and cycled. Verified proper function. Repair complete.

"Arrived on site to replaced previously diagnosed agitator, replaced agitator and tested, unit is now running as designed, no leaks detected, job complete."

Arrived onsite to replace control and both elements per service pointer. Replaced components and tested. Unit has no improvement. Recommend using a standard breaker or switching to a GE beaker that has had more success with GFCI\AFCI nuisance tripping.

Arrived on site to test unit for damaged handle. Replaced handle test unit and unit test good job complete.

"Arrived onsite for unit too warm. Found customer complaint was due to surface temperatures getting hot. Oven door glass ,handle and console. Instructed customer on surface temperature limits and that some components have no limit and can get uncomfortable to the touch . Job completed"

Arrived on site for washer needing previous diagnosised gearcase. Upon arrival confirmed issue and installed part. Tested unit and found no abnormal noises and no leaks. Washer works as designed call complete

Arrived on site to test unit for flames to high. Found unit on LP and orifice on natural gas. Will need LP conversation. Replaced orifice test unit and unit test good job complete.

Arrived on site to inspect dryer. The customer informed me a company came and cleaned her vents recently. I found poor airflow with my vent tester. I removed the vent hose and ran a cycle and found good airflow. I inspected the inside of the vent hose and found no kinks and also clear. I called Whirlpool techline and spoke with Robert 7737915958. The house vent is clogged. I instructed the customer to get their vents checked again.

Arrived on site and replaced previously diagnosed compressor. Vacuumed system and charged to specs. Compressor humming for five second and pulling 11amps then kicks right off. Charged system with nitrogen at145psi and allowed nitrogen to sit in system for 25mins with no signs of leaking. Under charged refrigerant and allowed to stabilize at 45psi on both low and high side. Compressor now kicking on. Running pressures are -10psi on low side and 80psi on high side. Documented findings with Techline and was advised unit will be submitted for review. Left unit undercharged so it would still run for customer while being reviewed. SR#7737916373

"WRS325SDHZ08 Arrived to inspect cooling issue. The customer had defrosted the unit fully and I inspected the evaporator area, after thermistors operative and the defrost element inoperative. I found one of the connectors had dislodged and after correcting, the issue was resolved and the defrost element heated as designed. I corrected the original defrost wiring mis-routing and reassembled. Operational test good, no leaks observed during service."

"Arrived on site for dryer making noise,this is a washer dryer combo. Removed panel. Found blower wheels turning independently from motor. Had to break off. Replaced motor and blower wheel. Verified operation. Call complete."

"Spoke with customer over the phone and explained unit would need to be rescheduled due to not having part/s on handed needed for repair, rescheduled customer for 12/06/23 to complete repairs with W10823720(FL burner), W11517959(FR burner); ordrng 1 Cnote (Spoke with sr who ordered parts for repair)"

"WRS315SDHW06 Arrived to install previous ordered parts. I removed and replaced the faulty compressor, noting no visible refrigerant leaks via UV dye, from the UV drier that had been previously installed with the weakened compressor. The unit began to cool as designed after the compressor replacement and I verified via thermography. No leaks observed during service."

Arrived on site to test unit for gas smell when oven on. Replaced valve test unit and unit test good. Job complete. No leaks present at this time.

Arrived on site to test unit for unit not starting. Replaced control board test unit and unit test good job complete.

Arrived on site to test unit for condensation building on mullion and FC door gasket. Found top 10 inches of mullion was 58 degrees and remaining mullion was 89 degrees. Unplugged condenser motor for 10mins and top 10inches was 61 degrees and remaining mullion raised to 104. Documented findings with Techline and unit will be sent for review for replacement due to separation. Job complete. SR#7737908923

"On arrival reverified complaint of noise. Replaced the ice maker fan as it is humming. Reassembled and ran test 3 to check operation. No noise noted. Showed customer, job complete no leaks detected during service. All operational test good."

"Arrived on site to replace previously diagnosed basket and suspension, replaced basket and suspension, tub ring was damaged also and needed to to replace, replaced and tested, unit is now running as designed, job completed"

"Arrived on site to inspect washer error codes. Upon further inspection, I placed the unit in diagnostics showing error code F8E1-long fill. Cleared the code and continued with testing. The unit failed to fill properly, but continued to test and it operated as designed other than the valves. I removed and replaced the valves and retested and unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site to inspect unit for not cooling freezer or fridge compartment. Upon arrival found frost build up on evaporator cover, saw the thermistor was in the wrong location per service pointer. Replaced damaged motor and moved thermistor to the correct location. Tested unit, unit is running as intended. Job complete."

"Arrived onsite for a dryer that only works in time dryer. Upon arrival I ran the unit with some towels in it and found that they were not making contact with the moisture sensor I adjusted the unit so that they did then tested the sensor at the P13. Red to black wire. And found that it ohmed out properly. I then ran the unit and found that the count down was stable but gas due to the fact the the towels where already dry. I got the washer wet and on the same cycle add the wet towels in and the time increase with the moisture content in the cloth like normal. Unit is operating as designed, I did ask the customer to monitor the unit."

"Arrived on site for unit not washing. Upon arrival ran diagnostics and got error code F4-E3 motor not running. Test unit and fills correctly, but wash motor is energizing but just not operating. Unit drains correctly. Need to replace sump and motor. Replaced sump and motor W11025157. Test unit and is operating as designed. No leaks present at this time. Job complete"

Ive been on site for a range that is not heating during bake cycles. Inspected unit and work area. The customer advised that it takes several hours to get to preheat and that it does not hold temperature. Gained access to the bake element and found it burned up. Replaced the bake element and tested the unit. The unit is working and operating as designed. Call complete.

Arrived onsite for walk making a noise. Customer said that during spin cycle it makes a squeaky noise. I ran diaper mode and found no noise. I tilt the unit back and the bolt holding the rotor on was lose. I pulled the rotor off and I inserted a new clutch and slider. Told customer to use the unit that I never heard the noise but did find a bolt lose on the rotor. The unit is open as designed and no water leaks detected during service.

Arrived on site to install previously diagnosed and ordered parts. I removed and replaced the dispenser and tested. The unit now operates as designed. No leaks observed during service.

Arrived onsite for WiFi issue . Replaced console. Unit is now connected to wifi all checks good.

Arrived on site to test unit for console not responding. Found start button and cancel buttons not working. Relaxed console test unit and unit test good job complete.

"Arrived on site to inspect washer not getting enough water. Upon further inspection, I found the unit settings on Normal wash with cool water, Medium deep fill and medium extra rinse. I placed he unit in diagnostics showing no error codes and tested. Unit is operating as designed. I tested the unit in a Normal wash cycle with a High Deep Fill and left all other settings the same as mentioned above. The unit began to sense then went to soak/fill and the basket was empty. Once the unit filled and went to a wash cycle, I paused the unit and advised the customer that the unit fills based on the weight of the clothing and with no clothing in the basket, the water level was correct for the settings. I made recommendations for use and care, as well as, detergent use. Unit is operating as designed. No repairs needed at this time and no water leaks observed during service, job completed."

I dont say for a dryer that has a broken handle. I confirmed the customer complaint and replaced the handle. Tested the unit in the unit is working and operating as designed. Call complete.

Arrived on site for refrnot making ice in either compartment. Upon arrival confirmed issue but found no errors for upper ice maker in diagnostics and both units harvested as designed. Found triple valve had failed and replaced it. Tested both ice makers and found no leaks. Informed customer to give unit 24 hrs to stabilize temps. Call complete

"Arrived on site to test unit found not turning on, tested unit found knob cracked and timer stripped, will need to replace timer and knob to fix issue, knob is run without but it is on order, office to reschedule when knob is in stock; O-emld tckt"

Arrived on site to test unit for F6E1. Found faulty console. Replaced console test unit and unit test good job complete.

"On arrival verified complaint of smell. Replaced cam and be,t as diag last time. Operational test good. Job complete no leaks detected during service."

"Arrived on site with additional fuses to test unit for blowing fuse every time. Upon arrival, removed unit from cabinet. Removed outer skin to inspect all wiring and components. All wiring appears good with no grounding. Found upper interlock has failed internally. Test unit using min breaker. Unit did not trip mini breaker and remained powered on. Test unit by heating cup of water for :30. Unit heats correctly. I used 1 fuse W10138793 and upper interlock switch W11551558. Test unit again and is operating as designed. Job complete"

MVWC555DW0 Arrived to install previously diagnosed and ordered parts. I removed and replaced the drive hub assembly and re-calibrated. Testing within automatic service mode showed the unit had regained all functions. No leaks observed during service.

"Arrived on site for front panel not working, confirmed buttons are not responding. Replaced ui panel. Verified operation. Unit was not responding the same to customers touch. Works just fine when I try. Called tech line. Sr# 7737913345. No further recommendations. Call complete."

"Arrived onsite for a DW that is showing 1 Pause 1 Pause - pause, repeat - Error Code. Upon arrival I found that there was no one home, I contacted the office about it and the office reached out to the customer but Gino answer. I waited 10mins and still no one showed."

Arrived onsite for a refrigerator that is not making ice. I found the motor on the icemaker defective. I replaced the icemaker and tested it. It went thru a harvest and filled properly. There were no water leaks present at the time of service. Call complete. Use Authorization Number W19ET30APL1.

Arrived on site to install previously diagnosed parts. Inspected unit and work area. I replaced the fill tube heater and icemaker and tested the unit. The unit is working and operating as designed. Call complete.

Arrived on site. Replaced defective mullion rail tested door operation good.

Arrived onsite for a refrigerator not making ice. I found the icemaker motor failing. I replaced the icemaker and tested it. It went thru harvest and filled correctly. There were no water leaks present at the time of service. Call complete.

Arrived onsite and replaced the shield. Unit is now operating as designed. All checks good.

"Arrived on site to inspect washer not working. Upon further inspection, I placed the unit in diagnostics showing no error codes and tested. The unit completed testing, but during agitation, it began to make a loud thumping noise and operated as designed in spin mode. I tilted the unit back and removed the rotor and found gearcase oil in the rotor (photo). I advised the customer of my findings and placed the rotor back on the unit and manually tested the agitation and it continued to make the thumping noise. I am ordering the gearcase, clutch, slider, agitator assembly, rotor and CNOTE-LSO PER CUSTOMER REQUEST and scheduled return service for 12/07/23 (MS). No water leaks observed during service.; ordrng 1 W11449841 (Gearcase) and 1 W10754448 (Clutch) and 1 W10734521 (Slider) and 1 W11260238 (Rotor) and 1 W11550891 (Agitator) and 1 CNOTE (LSO PER CUSTOMER REQUEST)"

Arrived on site to inspect gas range. The right cooktop grate is cracked which caused the grate to not sit level. I removed and replaced the grates and tested. The unit now operates as designed. No gas leaks detected during service.

Arrived on site for noise complaint. Ran diagnostics noise from damper control replaced damper control.m

"Arrived on site to inspect dishwasher door falling open. Upon further inspection, I tested the door functions and when I opened it at 45 degrees and let go of the door, it fell open. I pulled the unit out to find the right side door hinge spring had popped off again. I removed and replaced the hinge assembly and retested door functions and the unit is operating as designed. Tested in diagnostics showing no error codes and the unit is operating as designed. No water leaks observed during service, job completed."

Arrived on site to install previously diagnosed valve. Removed log valve and replaced with new. Updated software on unit with smarthq. Ran and verified proper operational noises. Repair completed.

Arrived onsite with new door. Removed old door. Replaced outer door and hinges. Door no aligned properly. Rails sent was white and the unit has black. Reordering. Office will call when parts arrive. ; ordrng 1 W11235462 (Rail right hand (black)inspect)

"Arrived on site to inspect microwave popcorn settings. Upon further inspection, I found the customer had a small countertop microwave on the counter and were comparing it to their built in microwave. Customer advised that the popcorn setting on their built in unit does not pop all of the kernels and theyre left with basically a half empty bag of popcorn, but when they use the small countertop microwave, it pops the bag of popcorn fully. I advised the customer that the bags of popcorn cook based off the wattage of the microwave and the more wattage there is, the more popcorn will be made. The built in unit only provides approximately 900 watts versus the countertop unit which is providing 1350 watts according to the label, which makes sense that the smaller countertop unit is cooking the popcorn better than the built in unit. I recommended the customer experiment with the times and leave the cooking level at 100% to find how long the built in will take to cook popcorn. Tested the unit and it is operating as designed with no error codes. I made recommendations for use and care and no repairs needed at this time. Job completed."

Arrived onsite for door glass separation. Inspected and used temp rated adhesive to Secured door. Secured and tested. Unit is functioning properly. Job complete.

"WDF331PAHS1 Arrived to inspect drying issue. There were no stored error codes within the service test mode and all functions were present, including the heating system. Discussion with the customer revealed they pre-rinse prior to loading and I encourage that action, but they were using very high-strength detergent pods. I advised this causes excessive foaming, which blocks heat transfer, which adversely affects drying and is a very frequent cause of dishwasher drying issues. The customer was also not utilizing rinse agent and I set the dispenser to the correct setting for their use and advised on how to fill it. I recommend the customer attempt use with a liquid, or powder, automatic dishwasher detergent and to only fill the dispenser cup 1/4, or around one TBSP. Use of the Pre Wash is also not advised, as it can also add to over-detergenting and drying issues. I also advised to run the hot water at the sink until hot, prior to starting the unit. The unit may have been in a safety heater lockout and service mode testing and reset could have cleared it. Operational test good, no leaks observed during service."

"WRS335SDHM00 Arrived to inspect leaking from dispenser. I found evidence of water that had pooled within the dispenser area and then steadily dripped into the drip pan and then onto the outer door and down to the floor area. There were remnants of melted and then re-frozen ice within the ice bucket and the customer advised they did have some power interruptions recently. I explained that power interrupted long enough, can allow the ice within the bin to start melting. This causes water flow into the dispenser area and subsequent dripping within the dispenser area, as experienced. I advised the customer to remove the ice storage bin anytime there is a prolonged power outage in the further. Operational test good, no leaks observed during service."

"Arrived on site to install new cold valve per tech line recommendations. Customer also provided me with new water lines to install. I replaced the valve and lines and verified good flow. I advised the customer that logical good repairs have been performed, and tech line recs. Only other possible cause can be low pressure from the house supply, and no other repairs should affect. Repair completed, no water leaks found."

"Arrived onsite for a washer that is making noise in spin. Upon inspection I found that the shield had come off and damaged the cam, I replaced the cam and temporarily installed what was left of the shield and will be ordering it and some new screws. I tested the unit and found the unit operating as designed ; ordrng 1 W11409708 (SHIELD) and 2 W11573574 (SCREW)s"

Arrived onsite to replace faulty basket. Replaced and tested. Unit is operating properly. Job complete

Arrived onsite and found unit operating with failed gasket. Replaced gasket taking care to install it without tears. Unit is now operating as designed.

"Arrived onsite for unit door falling apart and heat escaping from cavity. Tested and found door assembly separating. Need to order and replace Outer glass, name plate, , returning with handle. Igniter working during visit returning if needed. Office to reschedule ; ordrng 1 W11176456 (Outer glass) and 1 W11178521 (Nameplate)"

"Arrived onsite for a gas dryer that is not operating. Upon inspection I found that the unit tumbled and heated. Upon further inspection I found that the towels that in was using it tested the unit would,not touch the moisture sensor when tumbling. I adjusted the unit till they did and tested the unit and found unit operating as designed"

"Arrived on site to inspect unit for not heating or drying clothes. Upon closer inspection found cut off was faulty and open replaced cut off and the heater thermistor. Tested unit, unit is running as intended. Job complete."

On arrival verified complaint of noise. Found during visual check a toy under the pulley cover. During spin and agitate it would scratch against the tile. During component activation all components activated except drain pump. Ran drain and spin and drain pump activated. Drain pump is working but will need to order main board. Door latch was intermittent ordering door latch. ; ordrng 1 W11633359 (Main ACU) and 1 W11394572 (Latch)

Arrived on site to diagnose range with center burner not lighting. Tested and confirmed unit sparks but doesn't light. Disassembled burner head and found it full of grease/oil. Cleaned it out and reassembled. Tested and found burner lights properly every time. Repair completed.

Arrived on site to install previously ordered parts. Replaced motor 279811and blower wheel WP697772. Test unit and is operating as designed. Job complete

Arrived on site for a refrigerator that is leaking from the filter area. Inspected unit and work area. The customer advised the unit is not leaking from the filter but leaking at the evaporator. She advised that she had her home warranty company come out for this machine several times and they replaced the compressor. She advised that when they call back that they found the evaporator and that their home warranty would not cover the evaporator replacement. She showed me a photo of what the unit looked like. Took temperature inside the freezer section and found it at 25?F. Did find an ice ball up on the upper right hand corner in the freezer section. Ordering all sealed system components including lokring. The office will need to contact the customer when all parts are made available and I need to schedule for a three hour service.; ordrng 1 W11598433 (Evaporator) and 1 W11504423 (Cap to evaporator coupler) and 1 W11547313 (Compressor) and 1 Lokringkit (Lokring kit) and 1 W11506635 (Access valve) and 1 WPW10143759 (Drier)

Arrived onsite for a washer with the lid not closing. I found the lid plastic stressed and the hinges bent. I replaced the right hand hinge and was able to straighten the left side hinge. I replaced the lid and tested it. The lid is opening and closing correctly now. Call complete.

Arrived onsite for refrigerator not cooling. On inspection found the fc evap cover with 1/2 inch of frost. Informed the customer that it needed to be defrosted before we can work on the unit. Customer sign the waiver form on how to defrost refrigerator. Setup return for 12/07/23.; schdld next appmnt for 12/7 THU PM

Arrived onsite to install previously ordered part. Replaced sump and motor W11025157. Test unit. Unit is operating as designed. No leaks present at this time. Job complete

Arrived on site for dryer not drying. On inspection I put my meter in to monitor the heat. It went up 265? down to 120? then backup to 265? then back down. I felt the clothes n the washer and they seem to have to much water still in them. I told them to run the drain and spin cycle to extract more water for a week and see if the dryer dries the clothes faster. No water leaks detected during service.

On arrival verified complaint of multiple burners not adjusting correctly. Replaced RIght front left rear and left front inf switch. Used 2x wp3149404 and 1x wp3149400. Right rear needs to be ordered. All burners are now operating correctly except right rear. Ordering WP3148952. Rescheduled for 12/7; ordrng 1 WP3148952 (Right rear switch)

"Arrived on site to inspect unit for unit being stuck on choose language screen. Upon closer inspection unit is stuck on the screen to choose language and will not respond at all. Customer stated they turned the breaker off for 15 minutes and unit got stuck at same option screen. Took off console found a loose connection on display, reconnected the loose connection. Tested unit, unit is running as intended. Job complete."

18308Arrived on site to inspect OTR microwave. I found the cooktop bulb stays on 24/7. The control is needed to resolve. ; ordrng 1 W11552018 (Main control)

Arrived onsite to replace faulty basket. Replaced basket and tested. Unit is functioning properly. Job complete

Arrived on site to test unit for unit not washing. Test unit and found and wash motor. Replaced sump and motor test unit and unit test good job complete.

"Arrived on site for not operating correctly. Upon arrival ran diagnostics and got error code F7-E5 shifter fault. Ran automatic test cycle and unit filled, and drained correctly. Unit will not agitate or spin. Ran manual test and agitate and spin test failed. Need to order actuator, and control. Office to reschedule ; ordrng 1 W11607637 (Control) and 1 W11481722 (Actuator)"

"Arrived on site to replace previously diagnosed thermal fuse, replaced and tested, unit is now running but noticed that the heater is not disengaging, removed heater and found a toe ring making a contact with element and chassis, removed and tested, unit is now running as designed, job complete"

Arrived on site and installed new basket. Calibrated and leveled unit. Verified vibration is gone. Repair completed.

Arrived on site found console damaged again. Will order new console office to reschedule ; ordrng 1 W11620706 (Console)

"Arrived on site. Found insulation exposed and door not closing correctly,removed bottom kickplate installed insulation correctly and kickplate."

"Arrived on site for dryer not heating. Found heating element working properly, not venting properly. Used test kit to confirm vent is restricted. Advised customer vent need to be cleaned before being used. Left vent unplugged. ; used 1 W10106710 (Test kit) from stock"

Arrived onsite for unit will not shut off.and found unit is stacked. Found unit full of water. Found trickle from valve into tub in standby. Will require 2 man to unstack and replace valves. Ordering valves and 2 man. Called safety to report findings. Sr#7737837061; O-emld tckt