"Arrived on site to inspect microwave door damage. Upon further inspection, I found a piece of tape indicating where the damage on the microwave door was located. It was a very small dent (photo). I removed and replaced the door and tested the unit and it is operating as designed. Job completed."

"Arrived on site to inspect dryer damage. Upon further inspection, I found the front panel badly dented just below the vent area (photo). Also found the unit is in a closet, just behind the front door (photo), stacked on top of the washer (photo). I found some small dings in the door panels on the right side of the unit and on the closet door (photos). Also found a dent in the door on the back side where the closet handle has previously hit (photos). All apartment damages done before arrival. I placed my towel on the closet door handle to prevent it from doing further damage to the front door (photo). I slid the unit out just far enough to where I could reach the top panel screws and removed the top panel. I removed the front panel of the dryer and replaced the front panel transferring the door and strike to the new panel, along with the model/serial placard. Placed the unit back into the closet and tested operations. Both units are operating as designed. No water leaks; no, lint observed during service, job completed."

"Arrived on site to inspect unit for not tumbling but has power. Upon arrival custstated that the unit would stop tumbling during cycle and continue to heat and count the timer down. Found motor getting proper voltage, and no signs of belt slipping on idler. Will need to order motor and return. W11549461 rescheduled for 4/3/24; ordrng 1 W11549461 (Motor)"

Arrived on site for a dishwasher. That is good news on the beeping at the customer when they were trying to use it. Inspected unit and work area. The customer advised of the unit does not even fill with water and just makes an alarm sound. I ran the unit through diagnostics and found an F8 E4 (float switch open) errr code. I gained access to the float switch and found water residue inside the float switch area. I remove the water and tested the unit again. Found the unit still showing a float switch open issue. I went ahead replaced the float switch and tested the unit. See you in it began to work and operate as designed with no leaks present during operation. I did notice that the customer has oversuds inside of her dishwasher and did advisor to lessen the amount of soap used to use. The unit is working as design. Call complete.

On arrival verified complaint of no ice. Found ui is dim and ice maker has E2 error. Confirmed ice maker function and fill. Recommend replacing ice maker and ui. Temps are all correct. Rescheduled for 4/4; ordrng 1 W10864261 (UI)

"Arrived on site to test unit for not dispensing ice. Inspected unit found door switch was not getting pushed in enough due to the door being too low. Leveled unit, dispenser is now activating. Unit is running as designed, no leaks detected, job complete."

"Arrived on site for frost in freezer and gasket not sealing. Upon arrival, found left side of Fc door had about 12 of gasket that is not formed correctly. Formed gasket and door is now sealing correctly. Job complete"

"Arrived on site for F2-E0 error code. Upon arrival, inspected unit and error code F2-E0 appears on display. F2-E0 does not appear on tech sheet. Power cycled unit and none of the buttons are responding. Need to replace control. Replaced control and test unit. Unit is now operating as designed. Job complete"

Arrived on site for fridge making high pitch noise . Also complained about moisture building up between doors . No cooling issues found. Compressor is pulling correct amps . Ran temp checks on mullion got avg 34 . Ran compressor with condenser fan disconnected. Got an avg of 80. Called tech line and documented . Tech is passing it to customer service for exchange .Sr 7738776664. No water leaks detected at time of service. Job complete

Arrived on site for leaking dishwasher . Ran diagnostics and found leaking from the back . Pulled unit out and found large dent at upper corner left side at weld and leaking . Ordering tub . Call to set return ; ordrng 1 W11409866 (Tub)

Arrived on site to install previously ordered part. Replaced damper control. Test unit and is operating as designed. Job complete

"Arrived on site to test unit for no ice production. Found cutting grid was broken. Replaced damaged grid, allowed sheets of ice to form. Unit now working as designed. Job complete."

Arrived onsite for partial heating problems. Determined the product was miswired. Correct wiring. All checks good.

Arrived on site for unit Not wanting to start a cycle. Indicator kept beeping to close the lid. Inspected and found failed latch assembly. Replaced latch and tested. Unit is functioning properly. Job complete.

"Arrived on site for unit burner turning on by itself. Upon arrival found that what customer was trying to say was that the burner was turning off by itself. Inspected and found out what customer was experiencing was cool down On the burner element. notified customer that this cycling is normal operation. Also notified customer that the two main burners, when set to high, will stay on for a longer period of time. Tested several times with customer and customer now understands operations. Unit is functioning as design. Job complete."

"On arrival verified complaint of interior damage. Found liner is scraped on the right side above the drawer shelf, the top right shelf is scraped, the bottom bucket shelf on both doors are dented. The shelf support on the left and center are scratched as well. Documented with TL Rob 7738781120. TL requested we document with Jenn air and see how they want to proceed as well as confirming paint color for liner if needed. SW is calling JA for me. ; O-emld tckt"

On arrival verified complaint of unit not powering on. Found breaker is tripped. Us to sr had attempted to use the oven when breaker tripped. Verified voltage and polarity are correct. Took amp draw of L2 and had 10.6 on bake and 14.23 amps on broil. Set to max and max read 14.23 when breaker tripped. Retested with green wire disconnected and unit worked and L1 and L2 matched amps. Unit is working correctly but breaker failed. Spoke to TL Rory 7738778383. Customer signed voltage waiver. Completed check list. Job complete.

"Arrived on site to inspect wall oven microwave combo unit with the microwave light not working. Upon further inspection, I opened the microwave door and found the interior light is not coming on when opening the door. Using my microwave tester, I tested the unit to make sure its heating and when I started the microwave, I found the light continues to fail but the unit is heating. I placed my flashlight to the bulb and found the element is broken. I am ordering the microwave bulb and CNOTE-LSO PER CUSTOMER REQUEST and scheduled return service for 04/04/24 (MS). ; ordrng 1 W10886919 (MW bulb) and 1 CNOTE (LSO PER CUSTOMER REQUEST)"

"Arrived on site for unit with po message. At time of visit unit cooling correctly,per customer unit happened one day with po message and power cycle,ran diagnostics fan powered on,ran heater test passed ran all fans passed. Changed defrost setting to basic unit working correctly"

Arrived on site to test unit for clicking noises. Verified with customer damper is source of noise. Replaced faulty diffuser. Unit now working as designed. Job complete.

1221 is washer apt Arrived on site for washer making loud grinding noise . Found during diagnostics cam has failed . Replaced cam and actuator and capacitor. Reran diagnostics. All checked normal. No water leaks detected at time of service . Job complete

"Arrived on site to inspect unit for not draining properly. Upon arrival customer stated that the unit doesnt wash the dishes. Placed unit into test cycle confirmed unit is filling with water, but unit never sprayed water through spray arms. Will need to order pump and motor and return W11613570. Rescheduled for 4/5/24; ordrng 1 W11613570 (Pump and motor)"

Arrived on site to test unit for oven not getting to temp. Test unit and found unit average temp to be at 359? when set at 350?

Arrived onsite to test unit for unit no power. Found tripped breaker and turned breaker on and found right front burner not igniting. Will need to order burner head and orifice holder and screws due to rusted screws. Will need to research for burner screws office to reschedule ; ordrng 1 W11050487 (Orifice holder) and 1 WPW10515455 (Burner head) and 2 Partresearch (Burner screws)s

"Arrived on site for unit not heating correctly. Upon arrival, test unit by preheating oven to 350. Monitored temperature using thermocouple. Unit is cycling correctly but averaging about 10 degrees too cool. calibrated unit by 10 degrees. Unit is operating as designed. Job complete"

"Arrived on site to inspect wall oven vent issues. Upon further inspection, I found the black vent trim badly damaged and bent (photo). The vent appears to be good. I am ordering the vent trim, screws, and CNOTE-SCHEDULE AFTER 130PM and scheduled return service for 04/04/24. ; ordrng 1 W11648974 (Vent trim) and 1 CNOTE (SCHEDULE AFTER 130PM) and 2 WPY706189 (Screw)s"

"Arrived on site for a dryer. That is non-responsive. Inspected unit and work area. The customer advised that the unit does work most of the time, but that when they run several loads in a row, sometimes the unit will have a lit screen, and the touch buttons do not work with it. She advised that if she gives the unit an hour to two hours, itll turn back on and start working again. I checked the vac hose off the back of the unit and found part of the vent hose crunched. I tested the unit and found the unit tumbling and heating but did find an airflow issue within the unit. I did explain to the customer their issues with her airflow and that they are getting steam heating up into the user interface which is causing the control panel not to register any buttons being pressed. I did explain this is normal, but that they will need to fix their vent hose situation. The unit is working an operating as designed. Call complete."

"Arrived on site. Diagnosed a defective icemaker,replaced icemaker ran harvest test passed icemaker filled with water; used 1 W11700250 ( Icemaker) from stock"

Arrived onsite for ice machine shutting down. On inspection the unit would power down when the unit dumped water and the drain pump would turn on. The pump is going into flood stage and powering the unit down. Installed new drain pump and tested the flood stage. Poured water into the unit and it did not power down. The ice machine is operating as designed and no water leaks detected during service.

Arrived on site for washer being off balance. Damaged the wall. Found Service Pointer - W11684122. Will need new tub. No error codes stored. No evidence of oil underneath. Office will call to schedule. ; ordrng 1 W11172199 (Basket.)

Arrived onsite for a refrigerator to replace the previous diagnosed parts. I replaced the FC door. There were no water leaks present at the time of service. Call complete.

"Arrived on site to diagnose range with dead oven. Tested unit and could not get oven to heat. Found igniter glowing, but no gas. Tried moving igniter closer to manifold and saw the element crack and fall off. Replaced igniter and continued troubleshooting. Found igniter getting white hot, and could only barely smell gas. Ordering a safety valve since cooktop is working, but gas isn't being delivered to oven. Rescheduled for 4/4; ordrng 1 W11590292 (Regulator) and 1 W11620481 (Control) and 1 W11465032 (Main Harness)"

"Arrived onsite and found unit operating with f9e1 error code. Found no hi loop. Installed a hi loop. Cleared error and tested and determined the disposal plug had not been knocked and the unit was unable to drain. Corrected, All checks good."

"Arrived on site for not powering on. Upon arrival,test polarity and is correct. Removed top panel to access control. Am getting correct dc voltage to console. Console just will not respond. Need to replace console. Replaced console and test unit. Unit is operating as designed. Job complete"

"Arrived on site to inspect unit for broken door switch. Upon closer inspection found plastic tab of door switch broken off. Replaced door switch, tested unit, unit is running as intended. Job complete"

Arrived on site to replace igniter. Found DSI board shorted out. Will need to order new dsi board rescheduled for 4/3 ; ordrng 1 WPW10511278 (Dsi board)

Arrived onsite and replaced refrigerator door. Unit is now operating as designed. Advised customer on repair.

"Arrived on site to inspect washer being non responsive. Upon further inspection, I found the unit full of clothing and the door locked. I attempted to place the unit in diagnostics and the control panel failed to respond. Customer advised they checked the breakers and they were on. I found the breaker box in the laundry room and checked it and found the breaker tripped. When I cycled the breaker, the red indicator began to flash. I advised the customer that they should have the breakers checked and possibly replaced. Once I had the breaker reset, I placed the unit in diagnostics showing no error codes. Customer removed the clothing and I tested the unit in diagnostics. Unit is operating as designed. After testing, again, I recommended the customer have the breaker checked/replaced. I made recommendations for use and care, as well as, detergent use. No water leaks observed during service and no repairs needed at this time, job completed."

Arrived on site for drum not spinning when in use.Disassembled and found failed motor pulley. Replaced using truck stock WP8066184. Also used truck stock belt 341241. Reassembled and tested. Unit is functioning properly. Job complete

"Arrived on site for dryer, making a thumping noise. Upon rival inspected unit. Ran unit and could not duplicate any noise. Customer stated the noise had happened a few cycles in a row and was immediate upon starting the cycle. Loaded the dryer and tested again, but still could not duplicate any issues. Customer believes an item may have gotten stuck, but eventually worked its way out and is now functioning properly. Customer will monitor. Job complete."

Arrived onsite for door dishwasher falling down. On inspection the left spring is was off the hook. Attached the spring and add zip ties to the spring to prevent them from pops back off. The door is operating as designed no no water was detected during service.

"Arron site to inspect unit for not working properly. Upon closer inspection found unit jumping at beginning of cycle and shutting off within one minute. Motor sound like it has extreme load even while attempting to run empty. Also found unit unbalanced due to a broken leveling foot will need to order motor and leveling feet and return. Feet 49621, motor W11364931. Unable to find project manager or get him to answer phone. Office to reschedule ; ordrng 1 W11364931 (Motor) and 4 49621 (Feet)s"

"Arrived on site to test unit for no water. Tested unit found water valve was shut off. Turned valve on and tested, all components are engaging properly. Advised customer to use rinse aid with this unit and to prop open door after every cycle to help with the drying of dishes. Unit is running as designed, no leaks detected, job complete."

Arrived onsite for unit with failed load and go dispenser. Lid broken. Repaired the lid. Unit is now operating as designed. Advised customer on repair. Advised on basic checkup. Unit is in good working order.

"Arrived on site to inspect unit for not spinning and being unbalanced and shaking. Upon arrival leveled unit and raided legs up. Ran diagnostic cycle all components are activating. Ran drain and spin cycle to confirm unit spins and drains outside of diagnostic mode. It is spinning and draining on drain and spin. Replaced suspension due to age and wear and tear. Tested unit again, unit is running as intended. Job complete."

"Arrived on site to inspect unit for plastic door to filter not closing properly. Upon closer inspection found housing twisted due to over tightening of bolts on plastic housing. Adjusted unit, unit is now closing and not popping open. Job complete."

Arrived on site to test unit for oven not igniting. Test unit and found and igniter. Replaced igniter test unit and unit test good job complete.

"Arrived on site for a washing machine. That is not completing cycles. Inspected unit and work area. The customer advised that the unit will go through most of the cycle but that it sometimes does not complete out the cycle. I found the unit stuck in the drain upon entry and canceled out the cycle. Around the unit through diagnostics and found an F1 E1 (main control fault) and F2 E1 (UI stuck key) error codes. Due to the error codes, I went ahead and replaced the main control. Find the washer, unlevel and leaning towards the front left panel. I went ahead and adjusted the feet to level out the unit. I ran the unit through calibration cycle and then threw an auto test. Found the unit working an operating as designed. I did advise the customer that the issues with their main control, but did explain that off-balance loads will cause the unit to go into a drain mode and that they will have to cancel out that cycle in order to get the unit to start a new cycle. The customer was unaware of how to do that so I did show him. The unit is working an operating as designed. Call complete."

Arrived onsite and found unit is now working as designed following the last service. Spoke with property manager. All checks good.

"Arrived on site for a washing machine that is going off balance and is making loud noises during operation. Inspected unit and work area. The customer stated that the unit runs all right if there are no clothes in the washer. However, when the unit has closed in it, it goes off balance on every load. She advised that she has to run lighter loads in order to be able to get the unit to at least finish out the cycle. The customer had clothes in the washer and I ran the unit through a drain and spin. I confirmed the customers complaint and found that as the unit was starting to ramp up, the unit was going off-balance, and every which direction causing the basket to hit the side walls and start screeching. I gained access to the back and found the shocks worn, but still in place. I found part of the tub, starting to show signs of where, on the off-balance, and as I was spinning the rotor, I felt something stuck between the tub in the basket. I could not get the item removed and so I am ordering a full rebuild for this washer. The office will need to contact the customer about a return date due to an out of stock and PSP item.; ordrng 1 W11460604 (Tub) and 1 W11354541 (Stator) and 2 W11314394 (Spring)s and 6 W11314661 (Stator screws)s and 1 W11557803 (Rotor screw)"

Ordering ui control; ordrng 1 W11655738 (Ui)

"Arrived on site to inspect dishwasher damage to door. Upon further inspection, I found the lower right corner dented on the outer door panel (photo). I removed and replaced the outer door panel and transferred the control panel and handle to the new panel and tested the unit. Unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site to inspect range for error code and tripping breaker. Found breaker only tripped while using bake. All 4 cooktops powered on no issue, and broil worked. Heated unit with broil to dry out faulty bake element. After drying out element, set unit to bake and confirmed bake element is now working and not tripping the breaker. Picture of bake element glowing while reaching temperature included. Unit is running as intended. Job complete."

"Arron site to inspect clicking noise. Found rollers and idler had to much play as well as various places where unit could be tapping on itself. Replaced rollers, idler, and added pads. Tested unit, unit is no longer clicking and is running as intended. Job complete."

Arrived on site to add feet and sound pads. Replaced feet and added sound pads. Customer stated unit sounds way better. Unit is running as intended. Job complete.

"Arrived on site to install previously diagnosed parts. Replaced damper control no issues or noise after testing. Installed foam strip under gasket per Whirlpool service video. Fluffed up gasket with heat gun, FC door is sealing properly. At this time unit is running and functioning as designed, no leaks detected, job complete."

"Arrived on site to test unit for not drying dishes. Tested unit found all components engaging properly. Stated to customer that unit requires rinse aid to help the drying process. Advised customer to start using rinse aid and to prop open the door after cycle is complete to aid in the process of drying. Unit is running as designed, no leaks detected, job complete."

"KCGS556ESS05 Arrived to inspect ignition issue. The only affected burner was the center one and while down within the detention area, it would not ignite every time. This being an issue specific to the dual burner valve assembly, I advised the customer to keep the knob pressed during rotation and the issue is fully corrected. The customer was able to perform the ignition in that manner and I advised it on all of the other burners as well. Operational test good, no gas leaks detected during service."

"Arrived on site to test unit for power cord issues. Upon inspection power cord was uninstalled. Installed power cord with the hardware provided, tested unit, unit is now running as designed, job complete."

Arrived on site for me about powering on at all. Inspected unit and will not respond. Verified supply voltage and found plug was not inserted All the way into socket. Secured plug and tested. Unit is functioning as designed. Job complete

Arrived on site to install previously ordered part. Installed appliance manager. Test unit and unit is operating as designed. Customer will monitor unit.

"Arrived on site ,replaced basket ,suspension,gearcase ,cam and actuator . Basket came with new hub. Ran calibration and test wash . All checked normal . No water leaks detected at time of service . Job complete"

Arrived on site for dishwasher not washing dishes. Upon arrival confirmed issue and found f4e3 in diagnostics. Found wash motor failing and replaced it. Tested unit and found dishwasher working as designed with no leaks. Call complete

Arrived on site for a refrigerator that is frosting in the freezer section. Inspected unit and work area. The customer showed me exactly what was going on and we found frost buildup in the upper left-hand corner of the freezer section at the door. I found that the left-hand side of the door was not closing fully. I removed the door and check the slides. Found the left hand slide had not been fully pushed back at the factory. I adjusted the left-hand slide and tested the unit. Found the door opening and closing as designed with no air gaps present leading towards the frost buildup. I remove the frost up at the top of the freezer and advise the customer that they can either remove the rest of the frost or let it dissipate over the next few weeks. The unit is now working an operating as designed. Call complete.

"Arrived on site to inspect refrigerator light not working. Upon further inspection, the customer opened the right RC door and the RC interior light failed to turn on. I closed the switch and let it pop open and the light came on. I found the switch is sticking and will need to be replaced. I tested the unit and it is operating as designed other than the switch. I am ordering the RC right door switch, CNOTE-LSO PER CUSTOMER REQUEST and CNOTE-SCHEDULE RETURN SERVICE WITH TICKET #408284 and scheduled return service for 04/24/24 at the customers request. No water leaks observed during service.; ordrng 1 W11291138 (Switch) and 1 CNOTE (SCHEDULE WITH TICKET #408284) and 1 CNOTE (LSO PER CUSTOMER REQUEST)"

"Arrived onsite to replace previously diagnosed LED lights in FC. Replaced and tested, unit is functioning as designed, job complete."

"Arrived on site to test unit for excessive noise. Found no signs of gearcase failure. Basket is nice and balanced. Replaced gearcase, splutch assembly, suspension kit, belt, shift actuator and motor run capacitor. Unit working as designed. Advised customer to monitor and if issue persists to contact Maytag. No leaks detected. Job complete."

Arrived onsite to install trim on refrigerator. On inspection the trim part was broken. Ordering new trim. ; ordrng 1 W10714136 (Trim)

"Arrived on site for unit not powering on. Upon arrival, inspected unit and console is dark and not responding. Test polarity and is correct. Inspected junction box and connections are good. Found voltage ends between L1-fuse ( blk) wire in harness. No voltage is reaching control. Need to order harness. Office to reschedule ; ordrng 1 W11397505 (Harness)"

Arrived on site for cooktop being scratched by previous tech and burners not working right. Replaced panel. Front left burner flame is uneven and center burner has large flame. Switched burner head and now all problems are in front center. Does not have a simmer orifice. Will need new burner head and will require proper orifice. Reset for wed pm. ; ordrng 1 W11428599 (Convertion kit lp) and 1 W11319683 (Burner head)

Arrived on site to install new mounting bracket in right side. Secured bracket and unit to cabinet test unit and unit test good job complete.

Arrived on site to test unit for sparking. Test unit and found shorted doodle. Replaced diode test unit and unit test good unit heating correctly at this no sparking.

"Arrived on site to inspect washer not spinning out the clothing. Upon further inspection, I placed the unit in diagnostics showing error code F8E1-long/no fill. Cleared the code and continued with testing. The unit completed testing, but I noticed the water level not over the washplate when filling. The customer described the amount of clothing theyre putting into the unit which told me that shes not putting enough clothing into the unit and its not getting enough water which in turn is causing the unit to get off balance and not completing the cycle. Also found the customer is using too much detergent. I retested a few more times and each time I noticed the unit not getting enough water. I tilted the unit back and inspected the components underneath and found all components good. When I went to check the valve screens, I found the hot water valve, at the wall, was not turned on. Removed the hoses from the unit valve and inspected the valve screens and they are good and clear. Re-attached the hoses and retested the unit in diagnostics and this time the water level was correct and the unit completed testing. I made recommendations for use and care, as well as, detergent use. No repairs needed at this time. No water leaks observed during service, job completed."

Arrived on site for lights flickering. Found what seems like flickering on level 1. When switched to level 2 they are working normally. Called tech line. Level 1 has lower voltage and can appear to flicker but they are not. Working as designed. Call complete. File # 7738766335

"Arrived on site to replace top cabinet. Replaced cabinet, unit is now functioning as designed, job complete."

"Arrived on site to install previously diagnosed and ordered parts. Due to the gearcase failure of leaking oil and leaking oil onto the clutch and rotor, I removed and replaced the gearcase, slider, clutch and rotor and calibrated the unit. Tested the unit in diagnostics and it is operating as designed. No water leaks observed during service, job completed"

"Arrived on site ,replaced side trim pieces . Top panel is now sitting flush . No other issues found . No water leaks detected at time of service . Job complete ."

"Arrived on site to test unit for not being able to pull bin out. Found ram was stuck down preventing door from being opened. Found breaker was tripped. Reset breaker and replaced switch, unit now working as designed. Job complete."

"Arrived on site to replace suspension diagnosed on previous trip. Replaced suspension due to bounce in basket, replaced suspension bounce has decreased significantly. Ran diagnostic cycle unit is running as intended. No leaks present at this time. Job complete."

"Arrived on site for a refrigerator that is not making ice. Inspected unit and work area. The customer advised the unit had stopped making ice so they bought store-bought ice to be able to Spence ice other ice dispenser. After this, they noticed that the ice is completely clumped in the ice container and was causing the bay alarm on the icemaker not to be able to open and close properly. Since then, they have been able to get the icemaker to work. However, she advised that when they remove the ice clump from her ice container, the food inside of the freezer was falling out, and their ice cream was almost like soup. I took temperature of the refrigerator and freezer sections and found the freezer sitting at 3?F. I found the refrigerator temperature at 36?F. I found no evidence of any defrost issue or compressor issues with the unit. I ran the unit through diagnostics and did not find any stored error codes. I called whirlpool techline and spoke to Aaron SR# 7738770363. He had me ask the customer several questions about what happens with the machine whenever theyre losing their cool. The customer advised that the unit still has lights on in the refrigerator and freezer sections and that the machine just fixes itself when it wants to. Can you advise that it usually recovers within 24 hours of when they initially find The items defrosting. Aaron advised that because theyre not losing power and they are starting to re-cool within 24 hours of losing the call every single time, the issue would have to be with the door being left a jar. Advised to make no repair at this time and advise the customer to take a video of what is happening so that they can see if theres anything going on with the unit itself. I did advise the customer of techlines findings. Call complete."

"Arrived on site for a refrigerator that is not making ice. Inspected unit and work area. The customer advised the unit got stuck in the middle of a harvest and has not been able to be reset since. I did confirm that the twist tray was angled diagonally, and not moving. I tested the icemaker and found that the motor would not turn. I replaced the icemaker and tested the unit. Found the unit harvesting and filling as designed. The unit is working as designed. Call complete."

Arrived onsite for previously diagnosed parts. Installed the control board and ran the unit in diagnostic cycle. The unit completed the diagnostic mode with no issues. No water leaks detected during service.

Arrived on site to test unit for leaking. Ran unit for over 40 minutes no leaks present. Found customer had a lid on bottom rack blocking the spray arm from turning and can cause unit to leak. Advised customer to check unit after loading to make sure not is obstructing the spray arms from turning. Job complete.

Arrived on site to install previously diagnose to park. Inspected unit and work area. I replaced the door switch and found the unit working and operating as designed. Call complete.

Arrived onsite for dishwasher with error F7E2. Installed a new pump & motor and tested unit. Dishwasher completed the diagnostic cycle with no issues. The unit is operating as designed and no water leaks detected during service.

"Arrived onsite for knobs in wrong position. On inspection the 2 right knobs were interchanged, I switched back to the original spot."

"Arrived on site. Found filter housing defective,ran icemaker through a cycle diagnosed a defective icemaker,replaced icemaker and filter housing tested housing operation good ran harvest test passed ran fill test passed"

"Arrived on site for flames too large and melted knobs. Upon arrival, inspected unit and found all knobs have melted. Flames are too large. Adjusted all valves and flames are now correct. Replaced all knobs. Unit is operating as designed. No leaks present at this time. Job complete"

"Arrived on site to install previously diagnosed damper. Installed damper no noise present when tested. Sealed gap between liner and cabinet. Unit is now running as designed, job complete."

Arrived on site for dishwa needing upper rack. Upon arrival reconfirmed issue. Installed part and found it working as designed. Call complete

Arrived on site for a washing machine that wont drain. Inspected unit and work area. The customer advised the unit was doing just fine until it stopped draining at all. I checked underneath the washer and found no evidence of any broken wires. Gained access to the drain pump and found a piece of copper wire stuck inside the drain pump assembly and had eaten up at the impeller on the drain pump itself. Went ahead and replaced the drain pump and ran the unit through an auto test. Found the unit working and operating as designed with no leaks present during operation. Call complete.

Arrived on site to complete sealed system repair. On arrival. Customer stated they had went ahead and replaced the refrigerator. No need to complete todays visit.. Job complete

Arrived onsite to test unit for spark damaged in holders and rack. Replaced all holders and rack test unit and unit test good job complete.

Arrived on site for dishwasher not dissolving all the soap. Ran test and found no errors. Found spring on dispenser door broken so it never fully opened. Replaced dispenser. Verified operation. Call complete.

"Arrived onsite to replace faulty components. Replaced main board, UI and thermistor. Unit is functioning properly. Job complete"

Arrived on site to test unit for not washing. Test unit and found bad wash motor. Replaced sump and motor test unit and unit test good job complete. No leaks present at this time.

Arrived on site for dryer making a noise. Ran test and found lower wheel turning separate from motor. Removed door panel. Confirmed motor welded to blower and not turning. Had to break off motor. replaced motor and blower. Verified operation. Call complete.

Arrived on site for unit not dispensing ice. Replaced Auburn motor and coupling as instructed by previous tech. Tested unit and unit is functioning properly. Job complete.

"Arrived on site to inspect range oven damage and control issues. Upon further inspection, I found the control panel lower console pushed up into the control panel on the left side. I was able to pull it down and seat it properly. Customer advised the oven wasnt cooking properly and I found the unit temp display reading in Celsius. I went into the tools function and demonstrated to the customer how to change the temp reading and changed it to Fahrenheit. Demonstrated how to make changes in he control panel and made recommendations for use and care. Unit is operating as designed, job completed."

"Arrived on site to inspect unit for no power. Upon closer inspection found fuse blown replaced fuse, tested unit, unit is now powering on and heating. Job complete."