Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.
Local Reviews
for Niederwald, TX
Powered by Fluid LOCALQuick, promo service
Kenneth - Niederwald, TX
Leonardo C.
COOKTOP WHIRLPOOL WFC150M0JB0 Arrived on site to test unit for burners not staying red hot when on high. Test unit and found unit working as designed. Unit is new unit with regulated elements. Job complete.
Richard P.
REFRIGERATOR WHIRLPOOL WRF767SDHZ00 Arrived onsite for the refrigerator damper control making a noise. Replaced damper control and noise is gone. Damper control tested good. Complete
Richard P.
REFRIGERATOR WHIRLPOOL WRF767SDHZ00 Arrived onsite for the refrigerator making a noise. Ran diagnostics and found that the damper control is causing the noise. Will need to replace it. Ordering parts and office to schedule ; ordrng 1 WPW10479155 (control)
Richard P.
DISHWASHER WHIRLPOOL WDF331PAHS0 Arrived onsite for the dishwasher not washing. Ran diagnostics and found error code for motor not running. During testing found that the sump motor is not working. Replaced sump and pump and dishwasher tested fine and no leaks detected complete.
Jacob S.
REFRIGERATOR WHIRLPOOL WRX988SIBM03 Arrived onsite for ice maker working from time to time and ice clumping together and finding some water leaking on the side of the ice maker door. Looked at unit. Found that unit is making full bucket of ice with no problem. Let customer know that the ice needs to used to allow the auger to break up the ice inside the bucket. No leaks at this time. Job complete
Jacob S.
DRYER WHIRLPOOL FEX831FS1 Arrived onsite for unit making squeaking noise. Took unit apart. Added grease to wheel and bearing.
Richard P.
RANGE WHIRLPOOL WFC150M0EB3 Arrived onsite for the oven range not preheating. Installed new control and thermal fuse that was ordered and oven tested good . Complete
Richard P.
MICROWAVE WHIRLPOOL WOC54EC0HS02 Arrived onsite for the microwave door with a gap. Inspected the door and found that it was a little out of adjustment causing the gap. Adjusted door and the gap is gone and all functions tested fine. Complete
Jacob S.
RANGE WHIRLPOOL WFC150M0EB3 Arrived onsite to replace parts ordered by previous tech. Replaced part. Tested unit. Unit test good. No issues at this time. Job complete
Leonardo C.
RANGE WHIRLPOOL WFC150M0EB3 Arrived on site to test unit for oven not working. Test power and unit getting correct power and elements test good. Will need to order new Control board W11122555 and fuse thermal WP3196548. ; ordrng 1 W11122555 (CONTROL BOARD ) and 1 WP3196548 (FUSE THERMAL)
Richard P.
RANGE WHIRLPOOL WFC150M0EB3 Arrived onsite for the oven door not closing properly. During testing found that the door hinge is not working properly. Causing the issue. Ordering parts and office to schedule. ; ordrng 1 WPW10299225 (hinge-door) and 1 WPW10299227 (hinge-door)
Robert J.
WASHER MAYTAG MVWX655DW1 Arrived on job for complaints of not washing. Found the door latch not working. Replaced latch and test. No leaks detected at time of service.
Kevin B.
DRYER WHIRLPOOL FEX831FS1 "Arrived on site and replaced belt diagnosed on previous visit
Kevin B.
DISHWASHER WHIRLPOOL WDF330PAHB0 "Arrived on site and replaced washer motor No water leaks from connections at time of service. Dishwasher is now operating normally, job complete"
Kevin B.
DRYER WHIRLPOOL FEX831FS1 "Arrived on site and dryer is making a screeching noise while running. Disassembled dryer and replaced bearings and shaft and after reassembly screeching has stopped. ordrng 1 134503600 (belt)"
Kevin B.
DISHWASHER WHIRLPOOL WDF330PAHB0 "Arrived on site and inspected dishwasher and found wash motor isn’t running wash motor is normally
Jacob S.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 Arrived onsite for lights not turning on in unit. Tested unit. Found that light in the freezer compartment was not working. Ordered part. Rescheduled with customer. Customer already has LBH; ordrng 1 W11205083 (module)
Kevin B.
DISHWASHER WHIRLPOOL WDF330PAHB0 "Arrived on site and inspected dishwasher and found power to heating element has been turned off by Control board due to incoming water below 86° ran a diagnostic cycle and heating element is working properly at the end of cycle. Recommended to customer that hot water be run at the kitchen sink to prevent this. Customer is already using pods and rinse aid, no water leaks from connections at time of service, job complete
Robert J.
WASHER MAYTAG MVWX655DW1 Arrived onsite to replace parts previously ordered. Replaced gearcase splutch and washplate. tested washer and calibrated. Everything working properly no leaks detected. Complete
Leonardo C.
OVEN KITCHENAID KOSC504ESS00 Arrived on site to replace fuse. Replaced fuse test unit and found blower broken not turning. Replaced blower test unit and unit working as designed job complete
Leonardo C.
DISHWASHER WHIRLPOOL WDF330PAHB0 Arrived on site to test unit for unit not heating. Test unit and found bad heater. Replaced heater test unit and unit getting hot job complete no leaks present at this time.
Robert J.
REFRIGERATOR WHIRLPOOL WRX986SIHZ00 "Arrived on job for complaints not cooling. After exposing evaporator found completely iced over. Defrosted ice and discovered heater was not plugged in from factory. Reconnected tested operation, all functionality working properly."
Leonardo C.
OVEN WHIRLPOOL WOD51EC0AB05 Arrived on site to test unit for liner being damaged. Took pictures and talked to whirlpool. Send picture to tech support and per whirlpool tech damaged was not caused by the unit. Job complete File#7723439887
Leonardo C.
OVEN WHIRLPOOL WOD51EC0AB05 Arrived on site to test unit for liner being damaged. Took pictures and talked to whirlpool. Send picture to tech support and per whirlpool tech damaged was not caused by the unit. Job complete File#7723439887
Robert J.
WFC150M0EB0 Arrived on job for complaints of f9 code. Check wiring for error non found. Replace control and tested heating correct.
Robert J.
WRS325FDAM04 Arrived on job to replace start device. After replacement of starter check for frost pattern, good and no leaks. Job complete
Robert J.
Arrived on job for complaints of not filling with water. Found the inlet valve not working on cold side. Replaced valve and test. No leaks detected and operation normal.
Connor M.
MDB4949SDE maytag dishwasher Arrived on site to test unit for leaking during cycle. Found no failed components. Found excess soap build up in unit. Instruct custome ron only using 1 pod and instructed on proper usuage. Unit working properly, no leaks detected. POP attached to sdquickpic