Need Appliance Repair Service? Have a general question?
We love solving problems! Let us know how we can help by reaching out below.

Robert J.

WASHER MAYTAG MVWB765FW1 Arrived on job for complaints of noise. Found clutch making scrap noise. Replaced clutch and test spin and agitat. No leaks detected

Robert J.

WASHER WHIRLPOOL WTW4855HW1 "Arrived on job for complaints of washer not starting. Attempted to run diagnostics but program wouldn’t run. When attempting to run cycle lock light flashing. Replaced latch and test no change. Need control to complete repairs, office to schedule because availability not showing for control. ; ordrng 1 W11256099 (CONTROL )"

Diego G.

DISHWASHER KITCHENAID KDTE104ESS4 "Arrived on site. Checked for control issues. Found control intermittently shutting down in between cycles. Replaced main control and cycle, all functions tested OK. No leaks present. Job complete"

Diego G.

WASHER MAYTAG MVWX655DW1 "Arrived on site. Check for no operation issues. Found control intermittently not cycling. Replaced main control and cycled I went through all components, all functions tested OK. No leaks present. Job complete"

Diego G.

RANGE MAYTAG MER6755AAS "Arrived on site. Check for oven issues. Found bake element bad not allowing oven to get up to temperature. Replaced bake element and cycled, all functions tested OK. Job complete"

Diego G.

RANGE MAYTAG MER6755AAS "Arrived on site. Check for oven issues. Found bake element bad not allowing oven to get up to temperature. Replaced bake element and cycled, all functions tested OK. Job complete"

Diego G.

WASHER WHIRLPOOL WTW8500BW0 Arrived on site. When disassembling unit was not able to remove basket to take off bearing. Bearing shaft and basket binded together with corrosion and tried multiple attempts to remove but couldn’t. After further diagnosis will need to replace tub assembly with bearing and basket. Will need autho. Allow 2hrs on call. Office to resch; ordrng 1 ALLOW2HRS (ALLOW 2HRS ) and 1 CNOTES (CNOTES ) and 1 W10381078 (outer tub) and 1 W10549509 (basket)

Robert J.

DRYER MAYTAG MEDB765FW0 Arrived on job for complaints of not starting. Ran several test starting every time.

Diego G.

WASHER WHIRLPOOL WTW8500BW0 "Arrived on site. Check for spinning issues. Found multiple problems with unit. Found bearing bad and also rotor screeching on stater. Will need bearing, stater, Rotor and RPS sensor to repair unit. Need autho and 2 hrs for repair. Office to reschedule; ordrng 1 280146 (rotor) and 1 CNOTES (CNOTES ) and 1 W10178988 (sensor) and 1 W10419333 (stator)"

Diego G.

DISHWASHER HOTPOINT HDA3400G02BB "Arrived on site. Replaced timer and cycled, After further diagnosis also found switchs sticking creating unit to intermittently run. Will need switches to repair unit. Reschedule for 10/23/18 ; ordrng 2 3135-0006 (switch,intrlock)s"

Diego G.

DISHWASHER WHIRLPOOL WDT720PADM2 "Arrived on site. Replace control and sump and motor. Ran diagnostic test, all functions tested OK. No leaks present. Job complete"

Diego G.

WASHER MAYTAG MVWX655DW1 "Arrived on site. Checked for no operation issues. Found unit not advancing. Removed console assy and found loose connection at main board. Reposition connector reconnected, all functions tested OK. No leaks present. Job complete"

Diego G.

DISHWASHER HOTPOINT HDA3400G02BB Arrived on site. Check for advancing issues. Found timer bad not allowing cycle to advance. Was able to press on timer knob and get it to work but when I let go it stops. Will need timer to repair unit. Rescheduled for 10/16/18; ordrng 1 WD21X10155 (timer)

Diego G.

WASHER AMANA NTW4516FW2 "Arrived on site. Checked for no operation issues. Found control not responding and verified voltage to control. Replaced control and cycled, all functions tested OK. No leaks present. Job complete"

Joseph C.

WTW5000DW1 Arrived on site for “making grinding noises” complaint. Inspected unit and found inlet valves clogged with debris. Removed hoses and flushed valves and hoses. Reconnected hoses. Tested unit with towels and water. Unit is performing as designed. No leaks detected, at time of service.

Connor M.

WTW7500GW0 whirlpool washer Installed both parts and calibrated unit. Unit working properly, no leaks detected.

Carlos G.

Arrived on site and checked the unit for agitator issues. Confirmed broken agitator. Office to order for return visit. Rescheduled per Sarah.

Carlos G.

Arrived on site and checked the unit for no operation. Checked components and found a faulty control. Removed and replaced control. Ran calibration cycle. Ran test cycle and no error codes present. No water leaks present after service. Job complete.

Carlos G.

Carlos G.

Arrived on site and checked the unit for not washing issue. Checked components and found a faulty pump & motor. Removed and replaced pump & motor. Ran test cycle and all checks ok now. No wtaer leaks present after service. Job complete.