Near Dripping Springs, TX 78620
Brandon
Job Details: 07/25/2018
Arrived on site for part hanger, I replaced thermistor and installed screws as directed my tech line. Unit tested good, water lines were dry at time of service.
Near Killeen, TX 76549
Arthur B.
Job Details: 07/25/2018
WED8000DW3 (Dryer) - Arrived onsite for customer complaint of dryer making noises when tumbling. Removed front door assembly and blower housing cover. Found paper lodged inside housing rubbing on blower wheel. Removed obstruction and ed dryer. Dryer now heats and tumbles quietly. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Round Rock, TX 78681
Thomas L.
Job Details: 07/25/2018
Customer unloaded freezer prior to arrival. I defrosted frozen evaporator. I replaced or Mr. per manufacturers recommendations. Reassembled unit. Customer will reload.
Near Round Rock, TX 78681
Thomas L.
Job Details: 07/25/2018
Arrived on site for door and upper rack binding. With two people pulled unit from cabinet and tighten mounting screws for racks. Also leveled unit. Racks and doors now move smoothly. All water connections were dry. Please note that the replacement tank was damaged In the box. Return defective tank to James.
Near Round Rock, TX 78681
Lou
Job Details: 07/25/2018
arrived on site to inspect dishwasher not working and no lights coming on on the control panel. Upon further inspection, the customer turned the power on to the unit as its hard wired. No lights came on to the control panel and it had no functions. I quoted the customer DW135 $169.99 and $161.31 for a control panel for a total including tax of 358.63. The customer agreed to the repair and paid in full and I removed and replaced the control panel and tested the unit. Unit showed error codes 2/1 and 10/1 ate the beginning, so I cleared them and continued with diagnostics. The unit operated as designed with no error codes are the end of testing. No water leaks observed during service, job completed.
Near New Braunfels, TX 78130
Robert
Job Details: 07/25/2018
Near , TX 78617
Luis
Job Details: 07/25/2018
Refrigerator-replaced compressor
Near Georgetown, TX 78633
Tyler B.
Job Details: 07/25/2018
Near Killeen, TX 76549
Arthur B.
Job Details: 07/25/2018
MVWB725BW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer grinding when spinning. Found oil leaking from bottom and bearing grinding. Unit will need new bearing kit to complete repair. P&L are as follows; W10435302(Bearing) $111.51,TL230 $239.99 plus taxes. Customer declining repair due to to cost. Collected SVC call fee of $108.24 today. All water connections were dry at time of service
Near Manor, TX 78653
Nathaniel B.
Job Details: 07/25/2018
Model WGE745C0FS00, Arrived on call for f1 e1 which is upper rtd is uncalibrated, checked upper oven sensor and got 1.094 k ohms at 75 degrees, called whirlpool tech line and talked to mike, sensor is with in range, also checked lower oven sensor and got 1.154 k ohms which is with in range, cleared error codes after reseting power and the heated both ovens and with in 20 seconds got f1 e1 error, was instructed to replace the main control, file number 7722544437, preheated both ovens after installing control and all checks good errors did not return, call complete.
Near Manor, TX 78653
Nathaniel B.
Job Details: 07/25/2018
Model WGE745C0FS00, Arrived on call for f1 e1 which is upper rtd is uncalibrated, checked upper oven sensor and got 1.094 k ohms at 75 degrees, called whirlpool tech line and talked to mike, sensor is with in range, also checked lower oven sensor and got 1.154 k ohms which is with in range, cleared error codes after reseting power and the heated both ovens and with in 20 seconds got f1 e1 error, was instructed to replace the main control, file number 7722544437, preheated both ovens after installing control and all checks good errors did not return, call complete.
Near Round Rock, TX 78681
Lou
Job Details: 07/25/2018
arrived on site to install previously diagnosed and ordered parts. I tested the unit before replacing parts and found that the left front burner would not ignite. I removed and replaced the burner head and tested and the unit operated as designed. I noticed that the flames were too high on all of the burners so I adjusted each one. No gas leaks detected during service; job completed.
Near Austin, TX 78739
Kevin
Job Details: 07/25/2018
Arrived on site and found or a pool has sent freezer door directly to customer, after replacing freezer door interior liner is properly engaging with door switch. No water leaks from connections at time of service, job complete
Near Kyle, TX 78640
Leonardo
Job Details: 07/25/2018
Whirlpool oven turning off and not coming back on model: WEG745H0FS. Arrived on site to test unit for oven turning off and not coming back on. Test unit and found igniter not making contact with bake burner. Replaced ignitor test unit and unit test good job complete no leaks present.
Near Austin, TX 78748
Kevin
Job Details: 07/25/2018
Arrived on site and set washing machine into diagnostic cycle And found washer Motor will not engage but capacitor is buzzing. Capacitor will need to be replaced in order to correct issue. No water leaks from connections at time of service.
Near Killeen, TX 76549
Arthur B.
Job Details: 07/25/2018
NTW4516FW1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer “FINAL SPIN” light flashing and could not complete cycle. Was able to cancel out and ran calibration. Unit calibrated successfully. Did find water valve to home was shut off. Advised to make sure valve turned on before using unit. That way unit will not error out. No other issues found. All water connections were dry at time of service.
Near Killeen, TX 76543
Arthur B.
Job Details: 07/24/2018
MVWB865GW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not completing cycles. Ran diagnostics and found F0E3 (Off Balance) error. Ran test 052 and found gearcase grinding and clutch not engaging. Unit will need new gearcase and clutch to complete repair. R/S for Friday. All water connections were dry at time of service.
Near Elgin, TX 78621
Nathaniel B.
Job Details: 07/24/2018
Model WDT970SAHV0, Arrived on call for dishwasher top rack has to force it in to allow door to close and dispenser is not dissolving soap packs and there is a discoloration on inner dishwasher, found that discoloration is from calcium buildup, also found adjuster kit for top rack was bad so replaced it today and also found that the dispenser door is jamming, will need to order dispenser, will reschedule for 7/30/18, customer request 4-6 pm service, did instruct customer time frame is not a guarantee that he will get that time frame. And if there is a opening for sooner service to call him to see if he is available, did instruct customer on running hot water at sink before starting dishwasher and instruction on soap and rinse aid use.
Near Elgin, TX 78621
Nathaniel B.
Job Details: 07/24/2018
Model WDT970SAHV0, Arrived on call for dishwasher top rack has to force it in to allow door to close and dispenser is not dissolving soap packs and there is a discoloration on inner dishwasher, found that discoloration is from calcium buildup, also found adjuster kit for top rack was bad so replaced it today and also found that the dispenser door is jamming, will need to order dispenser, will reschedule for 7/30/18, customer request 4-6 pm service, did instruct customer time frame is not a guarantee that he will get that time frame. And if there is a opening for sooner service to call him to see if he is available, did instruct customer on running hot water at sink before starting dishwasher and instruction on soap and rinse aid use.
Near Leander, TX 78641
Lou
Job Details: 07/24/2018
arrived on site to inspect cooktop not working. Upon further inspection, I found that the breaker had been tripped. I verified voltage to the unit at the terminal block and voltage to all switches before testing unit. Once the breaker had been turned on and I verified voltage, I turned each burner on and the unit operated as designed. The customer advised that the last time he used the unit, he turned the left rear burner on and a red streak of light went from the switch to the burner. I also verified all wiring was good. I recommended that the customer have an electrician inspect the breaker to be on the safe side. Job completed.
Near Austin, TX 78753
Wesley
Job Details: 07/24/2018
Arrived on site and restored slipped suspension on washer.
Near Manor, TX 78653
Nathaniel B.
Job Details: 07/24/2018
Model MDBH945AWW, Autho. R173BV , Arrived on call to install rework element heater kit, installed kit and all checks good no leaks after repair, call complete. Installed heater rework that the customer was sent, see pic.
Near Manor, TX 78653
Nathaniel B.
Job Details: 07/24/2018
Model MDBH945AWW, Autho. R173BV , Arrived on call to install rework element heater kit, installed kit and all checks good no leaks after repair, call complete. Installed heater rework that the customer was sent, see pic.
Near Austin, TX 78754
Wesley
Job Details: 07/24/2018
WGD7500GC0 Arrived on site and found squeaking from dryer back rubbing against exhaust. Adjusted position squeaking subsided.
Near Austin, TX 78754
Wesley
Job Details: 07/24/2018
WTW7500GC0 Arrived on site and found chirping during spin from lid frame on main cabinet. Insulated with foam strip. Chirping subsided.
Near New Braunfels, TX 78132
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for icemaker issues. Found temperature at 61° inside refrigerator compartment and 0° in freezer. Found evaporator in refrigerator frosted over completely. Replace cover assembly and updated control and thought out evaporator. Instructed customer to allow 24 hours for unit to cool down completely and to start making ice.No leaks present. Job complete
Near New Braunfels, TX 78132
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for icemaker issues. Found temperature at 61° inside refrigerator compartment and 0° in freezer. Found evaporator in refrigerator frosted over completely. Replace cover assembly and updated control and thought out evaporator. Instructed customer to allow 24 hours for unit to cool down completely and to start making ice.No leaks present. Job complete
Near New Braunfels, TX 78132
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for icemaker issues. Found temperature at 61° inside refrigerator compartment and 0° in freezer. Found evaporator in refrigerator frosted over completely. Replace cover assembly and updated control and thought out evaporator. Instructed customer to allow 24 hours for unit to cool down completely and to start making ice.No leaks present. Job complete
Near Georgetown, TX 78628
Thomas L.
Job Details: 07/24/2018
Arrived -17 and 58 in fresh food . Found air return to freezer is totally frozen closed. Found no reason for possible air leak. Removed ice blockage for customer. Factory recommended no parts be replaced. Kesha and then Bruce at tech line assisted me. SR# 7722540992
Near Buda, TX 78610
Kevin
Job Details: 07/24/2018
Arrived on site and found top of frame glass is broken, quoted customer for Frame glass $140.98 total labor WO220 $189.99. After replacement oven door is now safe again and no further repair is required at this time, Job complete
Near Manor, TX 78653
Nathaniel B.
Job Details: 07/24/2018
Model DU1055XTSS3, Arrived on call for dishes not getting clean when washing, unit fills with water and drains and soap resolves but is leaving oily residue, found that customer is using to much soap with the finish gel packs, will need pump motor due to is pumping but only a trickle from lower spray arm and also will need dispenser due to rinse aid dispenser is broken, installed pump motor assem. Today and know is spraying as it should, instructed customer on soap and rinse aid use and will order dispenser, will reschedule for 7/27/18, customer requests morning appointment 8-10 am., see note. No water leaks after repair.
Near Manor, TX 78653
Nathaniel B.
Job Details: 07/24/2018
Model DU1055XTSS3, Arrived on call for dishes not getting clean when washing, unit fills with water and drains and soap resolves but is leaving oily residue, found that customer is using to much soap with the finish gel packs, will need pump motor due to is pumping but only a trickle from lower spray arm and also will need dispenser due to rinse aid dispenser is broken, installed pump motor assem. Today and know is spraying as it should, instructed customer on soap and rinse aid use and will order dispenser, will reschedule for 7/27/18, customer requests morning appointment 8-10 am., see note. No water leaks after repair.
Near Leander, TX 78641
Lou
Job Details: 07/24/2018
arrived on site to inspected no water entering dishwater. Upon arrival, the customer advised that she recent.y had a plumber come out and switch the hot and cold hoses on the kitchen faucet and the dishwasher did not work after that. She advised that the plumber came back and advised there was nothing wrong with the unit. I placed the unit in diagnostics and tested and there were no error codes. I continued with diagnostics and the unit operated as designed with no error codes at the end of testing. No water leaks observed during service. Job completed.
Near Cedar Park, TX 78613
Thomas L.
Job Details: 07/24/2018
Arrived on site or no operation. Found unit inoperable. In diagnostics I determined that the L2 failure code was present. It would not clear. The voltage was not a problem. Replaced control. Unit now powers up but will not start. Replaced open fuse. Operations are now normal and vent is clear.
Near Lampasas, TX 76550
Arthur B.
Job Details: 07/24/2018
WFW75HEFW0 (Front Load Washer) - Arrived onsite for customer complaint of front load washer locked and getting code F3E1. Ran diagnostics and confirmed F3E1 (Pressor Sensor) error. Removed top and found pressure hose was twisted throwing the error. Readjusted pressure hose. Clear error code and ran test cycle. Unit completed successfully. Advised customer to complete “Basket Clean” cycle. No other issues found. All water connections were dry at time of service.
Near New Braunfels, TX 78130
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for agitation issues. Found cam and belt worn causing unit not to agitate correctly. Replaced cam assy and belt and tested in diagnostics, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for agitation issues. Found cam and belt worn causing unit not to agitate correctly. Replaced cam assy and belt and tested in diagnostics, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for agitation issues. Found cam and belt worn causing unit not to agitate correctly. Replaced cam assy and belt and tested in diagnostics, all functions tested OK. No leaks present. Job complete
Near Cedar Park, TX 78613
Lou
Job Details: 07/24/2018
arrived on site to inspect dryer not working. Upon further inspection, I attempted to turn it on and when I pushed the start switch the unit did nothing. I verified voltage at the outlet and terminal block. I verified ohms at the fuse, cutoff and element. I verified voltage to the motor as well. I checked voltage at the start switch and found it open. I am ordering a start switch and scheduled return service for 07/27/18. No lint observed during service. I will return with roe screened parts in case there is something else going on with the unit.
Near Buda, TX 78610
Leonardo
Job Details: 07/24/2018
Whirlpool range no display on board model: WFE550S0HZ0. Arrived on site to test unit for no display on board. Test outlet and found 240 from red to black and 120 from red to white and 120 from black to white outlet checked good. Plugged unit and and checked voltage at terminal block from red to white and got 240 instead of 120 and 0 from black to white. Found bad power cord customer will go buy new cord and install job complete
Near Georgetown, TX 78633
Tyler B.
Job Details: 07/24/2018
Near Austin, TX 78737
Brandon
Job Details: 07/24/2018
Arrived on site for washer not opening door and not completing cycle. Put unit into diagnostic mode found water level error code and long drain error code, I found drain was very weak. I removed the back panel and gained access to drain pump, I removed the filter and found a clog. I removed the clog, unit tested good. Water lines were dry at time of service.
Near Lampasas, TX 76550
Arthur B.
Job Details: 07/24/2018
KUDS01FLSS2 (Dishwasher) - Arrived onsite to install new control, thermal fuse and latch assembly. Removed all parts and install new replacements. Reassembled. Tested unit. Unit now comes on fills,washes,drain and heats as intended. No other issue found. All water connections were dry at time of service.
Near Georgetown, TX 78628
Tyler B.
Job Details: 07/24/2018
Near San Marcos, TX 78666
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for no operation issues. Found terminal block bad. Replaced terminal block and secured power cord. Cycled all components, all functions tested OK. Job complete autho#wfq2yfqepl1
Near San Marcos, TX 78666
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for no operation issues. Found terminal block bad. Replaced terminal block and secured power cord. Cycled all components, all functions tested OK. Job complete autho#wfq2yfqepl1
Near San Marcos, TX 78666
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for no operation issues. Found terminal block bad. Replaced terminal block and secured power cord. Cycled all components, all functions tested OK. Job complete autho#wfq2yfqepl1
Near Cedar Park, TX 78613
Lou
Job Details: 07/24/2018
arrived on site to inspect dryer having a burnt smell. Upon further inspection, I found a large amount of lint debris inside the chassis. I vacuumed the lint out and found a small amount of lint debris inside the element chamber. I vacuumed the debris out and out the unit back together and tested and the burnt smell was gone. No lint observed at the end of service. Job completed.
Near Austin, TX 78723
Wesley
Job Details: 07/24/2018
UXT5230BDS1 Arrived on site to instruct on removal of mesh grease filter. Original filter damaged from install. Sending new filter d2c. All else checks good.Unit is operating as designed.
Near Kempner, TX 76539
Arthur B.
Job Details: 07/24/2018
UMC5200BAS (Wall Microwave) - Arrived onsite to install new mag,cap,diode to wall mount microwave. Removed all parts and installed new replacement. Reassembled. Tested with 1 cup for 2 mins. Unit heated as intended. No other issues found. Reinstalled back to wall cavity.
Near Lago Vista, TX 78645
Thomas L.
Job Details: 07/24/2018
Arrived on site for door issues. Found that the side and top trims have failed which cause the glass to fall and shatter. Removed and replaced all defective parts.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 07/24/2018
Model WFE320M0EW1, Arrived on call for cooktop cracked while cooking, replaced white cooktop and all checks good, call complete.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 07/24/2018
Model WFE320M0EW1, Arrived on call for cooktop cracked while cooking, replaced white cooktop and all checks good, call complete.
Near Austin, TX 78732
Cliff
Job Details: 07/24/2018
Kitchenaid oven KEBC107KSS05. Arrived on site to diagnose an oven that will not heat. Tested unit and found high limit thermostat open cutting power heating circuit. Failure is due to normal wear and tear. Replaced time limit thermostat and tested unit. Found all is functioning properly at this time.
Near Austin, TX 78752
Wesley
Job Details: 07/24/2018
WTW4815EW1 repaired clogged valve. Replaced valve and tested unit. All checks good.
Near Bee Cave, TX 78738
Brandon
Job Details: 07/24/2018
Arrived on site for customer complaint of soap residue on clothes after cycle. Found long fill error code, I put unit into diagnostic mode and found hot side fill valve was not functioning. I replaced water valve and housing, unit tested good. Also explained how to use washer for best results and soap usage. Water lines were dry at time of service.
Near Driftwood, TX 78619
Kevin
Job Details: 07/24/2018
Arrived on site and found three knobs are either broken or melting, quoted customer for knob replacement. Each knob $19.95, total labor CO350 $149.99, -$99.99 covered by jenn air safety team. Customer will not be continuing with repair at this time.
Near Buda, TX 78610
Kevin
Job Details: 07/24/2018
Arrived on site and inspected dishwasher and found that it will not go into diagnostic cycle. However normal cycle will start properly, it will also start with the door open. Inspected latch assembly and found handle is broken off. Quoted customer for latch assembly $52.65 and total labor DW155 $159.99 -$50 multiple appliance discount. No water leaks from connections at time of service.
Near Kempner, TX 76539
Arthur B.
Job Details: 07/24/2018
MEDB835DW4 (Dryer) - Arrived onsite for customer complaint dryer not heating and getting error code F4E4 (L2 Low Voltage). Checked incoming voltage and found only 120V coming into unit. Checked outside breaker and found one pole tripped. Reset breaker and retested voltage. Found 240V coming into unit. Tested unit. Unit now heats as intended. Collected SVC call fee of $108.24 due to 90 day customer instruct period. Dryer vent and lint trap was clean of lint at time of service.
Near Austin, TX 78753
Nathaniel B.
Job Details: 07/24/2018
Model WRT348FMES00, Apartment 5105, Arrived on call for food freezing in fresh food section, previously diag. That main control no reading fresh food sensor, today installed control and instructed customer to allow for 24-48 hours for proper cooling in fresh food section, no water leaks at time of call, call complete.
Near Austin, TX 78753
Nathaniel B.
Job Details: 07/24/2018
Model WRT348FMES00, Apartment 5105, Arrived on call for food freezing in fresh food section, previously diag. That main control no reading fresh food sensor, today installed control and instructed customer to allow for 24-48 hours for proper cooling in fresh food section, no water leaks at time of call, call complete.
Near Cedar Park, TX 78613
Lou
Job Details: 07/24/2018
arrived on site to inspect refrigerator lights not working. Upon further inspection, I found that the rc lights were barely on and the fc light was not on when the door was open. I removed and replaced the fc light and all lights began to work as designed. No water leaks observed during service. Job completed.
Near Austin, TX 78744
Leonardo
Job Details: 07/24/2018
Whirlpool range damaged panel model: WFG505M0BS3. Arrived on site to test unit for damaged panel. Replaced panel test unit and unit test good no damaged found on new panel job complete no leaks present at this time.
Near Leander, TX 78641
Thomas L.
Job Details: 07/24/2018
Arrived on site for improper fresh food temps. Found temp at 52. Found evap fan not running. Found fan harness not properly connected. Corrected. Fan now runs. All water connections were dry.
Near Cedar Park, TX 78613
Lou
Job Details: 07/24/2018
arrived on site to inspect dishwasher door not closing. Upon further inspection, the customer advised that the unit is not getting water and the right side of the door is not sealing. I found that the valve to the water coming out of the house was turned off. I turned the valve on and the unit began to dispense water into the tub. The unit is sitting on an uneven floor which makes it look like the door is sagging or not closing well. I demonstrated to the customer that if I were to raise the unit on the right side, the door would drag when closing causing it to hit on the right side of the chassis. The floor is uneven approximately 1/8 of an inch. I placed the unit in diagnostics and tested and the unit operated as designed. I found a large amount of soap debris in the tub and advised the customer to stop using detergent pods as they produce too much soap and can damage the unit. I recommended that they use liquid or liquid gel and no more than two teaspoons and to use rinse aid as wel
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 07/24/2018
Model WMH32519FS0, Autho. WFN9800EPL1, Arrived on call for burn mark by light casing, found that the burn mark was on the plastice cover ends of wires for under light and socket for under light which is normal on the plastic but did not melt just has a discoloration which i see on all models that have use, installed under light socket and new light bulb that customer purchased and checked operation and under light is working as it should, original bulb the glass part of it separated from the metal part of the bulb, all checks good, call complete. No parts needed.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 07/24/2018
Model WMH32519FS0, Autho. WFN9800EPL1, Arrived on call for burn mark by light casing, found that the burn mark was on the plastice cover ends of wires for under light and socket for under light which is normal on the plastic but did not melt just has a discoloration which i see on all models that have use, installed under light socket and new light bulb that customer purchased and checked operation and under light is working as it should, original bulb the glass part of it separated from the metal part of the bulb, all checks good, call complete. No parts needed.
Near Fort Hood, TX 76544
Arthur B.
Job Details: 07/24/2018
MEDX655DW1 (Dryer) - Arrived onsite for customer complaint of no heat on dryer. Checked voltage and getting proper 240v. Removed back panel to check element and cutoff. All checks ok. Did checked voltage from motor to element and found no voltage. Unit will need new motor to complete repair. Ordering motor and timer just in case but may not need. Dryer vent and lint trap was clean of lint at time of service.
Near Austin, TX 78753
Wesley
Job Details: 07/24/2018
Wes571cIDM02 arrived on site and found unit with very slow trickle of water flow. After replacing water line parts found unit pressure from house super low. Advised customer on findings. All else checks good.
Near Lakeway, TX 78734
Brandon
Job Details: 07/24/2018
Arrived on site for customer complaint of dryer not working properly on auto dry, I used the vent test to check for clog in exhaust vent, I found vent was clogged and needed cleaning. I showed customer the vent test and explained how it works, and instructed him to get the vent cleaned before using the dryer again. Vent was not clear at time of service.
Near Buda, TX 78610
Kevin
Job Details: 07/24/2018
Arrived on site and set oven to preheat and it reached temperature in expected amount of time. Bank barn or turned off at 372° and reignited at 361° lower temperature 10° overall I showed customer how to make further adjustments if they wish to. No for the repair is required at this time, job complete.
Near Austin, TX 78756
Luis
Job Details: 07/24/2018
Refrigerator-installed deli control
Near Round Rock, TX 78665
Tyler B.
Job Details: 07/24/2018
Near Bee Cave, TX 78738
Brandon
Job Details: 07/24/2018
Arrived on site for dishwasher dispenser not staying closed, found dispenser was broke and needed replacing. I removed the outer door and replaced soap dispenser, unit tested good, no leaks at time of service.
Near Austin, TX 78739
Leonardo
Job Details: 07/24/2018
Maytag dishwasher no high rise loop. Model:MDB4949SDZ0. Arrived on site to test unit for no high rise loop. Got high rise loop and secured high rise loop to make sure it would stay. Test unit for back flow and no back flow present at this time. Job complete
Near Killeen, TX 76549
Arthur B.
Job Details: 07/24/2018
WDTA50SAHB0 (Dishwasher) - Arrived onsite for customer complaint of dishwasher scrapping when closing door on RH side. Found RH leg on tub had came off raised tile floor. Was able to adjust leg back to tile. Used mounting brackets to secure unit to under counter. No other issues found. All water connections were dry at time of service.
Near Liberty Hill, TX 78642
Lou
Job Details: 07/24/2018
arrived on site to install previously diagnosed and ordered part. I removed and replaced the drain tube that goes from the drain pump to the drain pipe. I verified my connections and placed the unit in diagnostics to test. Unit operated as designed and no water leaks were observed during service. Job completed.
Near Lockhart, TX 78644
Joseph C.
Job Details: 07/24/2018
WTW8040DW4 Arrived on site for “shaking, during spin cycle” complaint. Inspected unit and found it in level condition. Rear right suspension sprung and dropped down. F0E5 error code present. Removed and replaced suspensions. Tested unit. Unit tests good. No leaks detected, at time of service.
Near Austin, TX 78731
Luis
Job Details: 07/24/2018
Refrigerator-installed updated control kit to allow water to dispense correctly
Near Austin, TX 78738
Brandon
Job Details: 07/24/2018
Arrived on site for washer lid locked and unit did not complete cycle, found no power was getting to unit and breaker was tripped. I reset the breaker and put unit into diagnostic mode, found unit was functioning properly on all test cycles. Water lines were dry at time of service.
Near Leander, TX 78641
Thomas L.
Job Details: 07/24/2018
Arrived on site for no ice condition. Found inlet fill tube frozen solid. Removed ice blockage and replaced inlet water valve. All water connections were dry.
Near Killeen, TX 76542
Arthur B.
Job Details: 07/24/2018
WRV986FDEM01 (5 Door Refrigerator) - Arrived onsite to install new deli pantry control to 5 door refrigerator from my prior diagnosis. Removed deli control and installed new replacement. Removed all ice from RC evaporator cover. Reassembled and powered unit. Unit now powers on and does not reset. No other issues found. All water connections were dry at time of service.
Near New Braunfels, TX 78130
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for no operation issues. Found error for overload. Ran through diagnostic test to test all components, all functions tested OK. Instructed customer that king size comforters will not wash correctly in the washer and will have issues. No leaks present. Job complete.
Near New Braunfels, TX 78130
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for no operation issues. Found error for overload. Ran through diagnostic test to test all components, all functions tested OK. Instructed customer that king size comforters will not wash correctly in the washer and will have issues. No leaks present. Job complete.
Near New Braunfels, TX 78130
Diego G.
Job Details: 07/24/2018
Arrived on site. Check for no operation issues. Found error for overload. Ran through diagnostic test to test all components, all functions tested OK. Instructed customer that king size comforters will not wash correctly in the washer and will have issues. No leaks present. Job complete.
Near Round Rock, TX 78665
Tyler B.
Job Details: 07/24/2018
Near Austin, TX 78735
Brandon
Job Details: 07/24/2018
Arrived on site for part hanger, I replaced ice maker fill tube, unit tested good. Water lines were dry at time of service.
Near Austin, TX 78757
Wesley
Job Details: 07/23/2018
Kfcs22evms8 Arrived on site and found unit operating quietly and at the right temperatures. No ice build up on Evap. Noise had come and gone after diagnostic test. Seal check good and heat treated to restore suppleness. Advised customer on use and care.
Near Buda, TX 78610
Kevin
Job Details: 07/23/2018
Arrived on site and found no excessive noise from refrigerator, wall to the right Has been damaged, took one picture. Found lower grill is in place, took one picture. Since there is no excessive noise did not move refrigerator forward to prevent further damage to wall. No water leaks from connections at time of service.
Near Leander, TX 78641
Lou
Job Details: 07/23/2018
arrived on site to inspect washer stopping in the middle of cycle. Upon further inspection, I found that the unit was full of water and unplugged with the water turned off. Customer advised that the unit stopped while washing and was leaking from underneath so they unplugged the unit and turned the water source off. I plugged the unit in and turned the water back on and found the unit full of water. I pressed and held the start button until the unit went into drain mode and pumped all of the water out. I verified that the drain hose was zip tied down at the drain pipe too. I placed the unit in diagnostics mode and checked for error codes and there were none. I cleared codes anyway and continued with testing and the unit operated as designed with no error codes at the end of testing. I checked underneath the unit for any signs of leaking and found none. I snapped photos of the drain pump and drain hoses from underneath the unit. I put the unit back into place and leveled the unit and pl
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 07/23/2018
Model WRV986FDEM01, Arrived on call for fresh food not cooling but freezer temp is good found fresh food set at 33 degrees and actual temp on fresh food product is 53 to 59 degrees, called whirlpool tech line and talked to bruce then kurt 7722529740, found fresh food compartment sensor and evap sensor are checking good and evap sensor has the correct placement per tech line and is secure to the freon line, was instructed to replace the ui control for not reading sensors, ui control controls the operation of cooling for the sensors per tech line, also found that ice room fan is only getting 6 dc volts to it when forced on and is running very slow, will need main control and also adapter kit due to moisture and ice at rear adapter kit, will need autho. For repair, office will reschedule with customer if autho. Is approved. No water leaks at time of call., will need autho.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 07/23/2018
Model WRV986FDEM01, Arrived on call for fresh food not cooling but freezer temp is good found fresh food set at 33 degrees and actual temp on fresh food product is 53 to 59 degrees, called whirlpool tech line and talked to bruce then kurt 7722529740, found fresh food compartment sensor and evap sensor are checking good and evap sensor has the correct placement per tech line and is secure to the freon line, was instructed to replace the ui control for not reading sensors, ui control controls the operation of cooling for the sensors per tech line, also found that ice room fan is only getting 6 dc volts to it when forced on and is running very slow, will need main control and also adapter kit due to moisture and ice at rear adapter kit, will need autho. For repair, office will reschedule with customer if autho. Is approved. No water leaks at time of call., will need autho.
Near Austin, TX 78752
Wesley
Job Details: 07/23/2018
W!H31017DS0 Arrived on site and installed control due to scratching. Unit now checks good.
Near Buda, TX 78610
Brandon
Job Details: 07/23/2018
Arrived on site for refrigerator not cooling at all, found compressor, and fan motors were not running, found UIB was non responsive to commands and I could not access diagnostic mode. I found control board was bad, I replaced control board, unit tested good.
Near Leander, TX 78641
Lou
Job Details: 07/23/2018
arrived on site to inspect oven showing error code 5/1. Upon further inspection, I checked for voltage at the P5-5/neutral and P5-6/neutral and received no voltage. Per the diagnostics in Service Matters, I removed and replaced the main control and tested the unit and the unit operated as designed. Job completed.
Near Austin, TX 78738
Luis
Job Details: 07/23/2018
Refrigerator-installed updated icemaker kit
Near Temple, TX 76501
Arthur B.
Job Details: 07/23/2018
MFF2557HEQ (French Door Refrigerator) - Arrived onsite customer complaint of icemaker not making ice on French door refrigerator. Found water valve cracked in rear and icemaker stuck mid harvest. Removed valve and icemaker and installed new replacements. Reassembled. Turned water supply on. No leaks found. Icemaker called for water immediately. No other issues found. All water connections were dry at time of service. Unit is cover per thru Assurant Ext Warranty.
Near Buda, TX 78610
Connor M.
Job Details: 07/23/2018
Wdf510pay82 whirlpool dishwasher Arrived on site to test unit for wash quality issues. Found complaint to be missing leds on control and dishes not drying. Replaced control and confirmed operation of element. Unit working properly, no leaks detected.
Near Liberty Hill, TX 78642
Thomas L.
Job Details: 07/23/2018
Arrived on site for icing in freezer section. Found items in the left side of the pizza bin pushing against crisper causing left side of door to push out and not seal. Corrected and adjusted door gasket. All water connections were dry.
Near Austin, TX 78733
Luis
Job Details: 07/23/2018
Refrigerator-replaced water line to dispenser,compressor,evaporator and filter drier.