"WFES3030RS0 Arrived on site for a range with no power. On arrival, I verified that the range was tripping the breaker. I removed the ground wire and preheated to five hundred degrees temperature reached without tripping breaker. I checked polarity, and voltage readings were correct . I took amp draw only oven on it was 15.13 amp draw. With all burners on high and oven on, it was 40.24 over the 40 amp breaker to clients' homes. I rewired the ground wire back on and preheated to five hundred degrees temperature reached without tripping breaker. I recommend that the client leave the oven running for one hour. I recommend that the client contact the breaker company for information on the correct gfci breaker for the range and also to notify the home builder to replace the gfci breaker. No parts used calling whirlpool safety case# 21027907"

"EED4300TQ0 Arrived on site for a dryer not powering on. On arrival, I verified no power I tested the thermal fuse part has failed. I replaced thermal fuse, and now we have power.Timer was failing, so I replaced it then tested. Dryer is working as its designed. I recommend client have a professional clean the ducts to there home it was in terrible condition. working as its designed."

"WDF341PAPB2 Arrived on site for a dishwasher not filling with water. On arrival, I verified that the motor pump has failed. I replaced the motor and then tested product is working as its designed no water leaks visible from main water supply."

Arrived on site for dishwasher not drying. Found F7e1. Cleared codes. At control I checked OWI and got 48k ohms. This is within range. Heater circuit checks good. Heater pulls 7 amps while running. Unit is working as designed. Suspect code was not reset. Call complete.

"Arrived on site for refrigerator not dispensing ice. On arrival found teeth, jammed in the bucket, causing unit not to dispense. Replace w 11185686 container and found unit dispensing ice as design call complete."

"wmh31017hs10 Arrived on site for a otr microwave making nosies. On arrival, I verified that the blower fan is failing. I replaced the blower motor then tested product is working as its designed."

Arrived on site for a WOS51EC0HS20 oven gettingan error for the cooling fan. Found the control wasn't sending the correct voltage. I replaced the control w11261167 and heated the oven without any errors.

"Arrived on site (unit was moved to apt#2301) for refrigerator model number WRS325SDHZ08 needing SS repair. Upon arrival, inspected unit and confirmed the compressor (W11580057), filter drier (WPW10143759), and access valve (W11506635) needed to be replaced. Unit is now operational; job complete. No leaks observed during service."

"Arrived on site for refrigerator model number WRS571CIH04 not cooling. Upon arrival, we discovered the evaporator cover was frozen over. I called the whirlpool tech line and spoke with George SR#21054679 who suggested replacing the heater W11546981 and bimetal strip W11566475 Parts have been ordered and told customer to unplug fridge 2 days prior to follow up service on 10/13. NEEDS MORE WORK.; ordrng 1 W11546981 (Heater) and 1 W11566475 (Bimetal harness)"

"Arrived on site for dishwasher model number WDP540HAMZ2 with no heat/hot water. Upon arrival, initiated a test cycle and observed a F7/E1 error code but all components were functional to include the heating element. Informed customer that a test cycle may have been needed after the wash motor was replaced on the previous visit. Customer also mentioned that rinse aid was leaking from dispenser which also explains why dishes weren't drying. Ordered new dispenser W10861000 and told customer we would return for repair on 10/13. No leaks observed during service. NEEDS MORE WORK.; ordrng 1 W10861000 (Dispenser)"

"Arrived on site to install shaft into microwave KMBS104EBL03. Removed unit and turntable motor, then affixed turntable inner shaft W11126044. Reassembled unit and tested. Verified unit working as designed. Repair completed."

"Arrived on site for dryer model number WED560LHW2 with unit not spinning. Upon arrival, ran diagnostics and observed F3/E1 error code. Inspected unit and noticed the belt was broken, replaced belt with repair kit 4392067. Unit is now functioning properly. Job complete."

"Arrived on site for oven too hot. Upon arrival, customer stated sometimes their food will burn. Check oven temp with thermocouple and found 395F when preheating to 350F bake. Advised customer to calibrate unit to desired setting. Customer agreed. Unit is functioning as designed. No parts needed"

Arrived onsite for WDT531HAPM0 and installed a new dispenser W10861000. Unit is now operating without dispenser leak. Advised maintenance on repair.

Arrived onsite and tested unit MDB4949SKZ0 and found operating properly. Replaced vent W11649995 and Found operating properly following last service. Unit is now operating properly.

"Arrived on site for oil present on top of unit. Upon arrival, proceeded to test unit and found no issues heating and tumbling. Upon closer inspection, found orange scented cleaning oil on the top rack above the dryer. Smelled tested the oil on the dryer and the cleaning oil and its the same smell. Possible spillage from cleaning oil that dripped down to the dryer. Showed customer and understood how that could have been a possibility. Unit is functioning as designed. No parts needed"

"Arrived on site for range JDRP636HL01 for not heating to temperature. Upon arrival, test unit by preheating to 400 and monitored using thermocouple and only heats to 347. ran diagnostics and there are no saved error codes. I test polarity and is correct. Test resistance of bake element and is 20 ohm. Am getting 235 v at bake element. All components test good. After power cycling unit I test bake again and this time reached 400 and began heat cycling . Unit is now operating correctly. I believe the unit needed to be power cycled to restart the control. Unit is operating as designed. Job complete"

"Arrived on site to diagnose dishwasher WDT751SAPZ1 that is not filling with water. Tested unit, could hear valve buzzing loudly but no water coming in. Builder says they confirmed there is water at the tap. I moved the unit out to check the hose and found it folded in half, cutting off all water flow. I straightened the hose and replaced the inlet valve W11434044 due to it running dry several times. Tested and confirmed proper operation. Verified no water leaks observed during service. No one on site to sign for ticket."

"Arrived onsite for WMH31017HZ09 and found bad diode burnt. Repaired by replacing the diode W11256462. Unitnis now operating as designed, tested by heating glass of water. Advised tenant on repair."

"Arrived on site for washer model number WTW4855HW3 with pump running continuously. Ran diagnostics and observed F3/E1 error code, replaced control board W116076 via service pointer S153EB. Unit is now functioning properly. Job complete. No water leaks observed during service."

Arrived on site for washer MVW5430MW1 with complaint of not operating with lights blinking. Upon arrival inspected unit and found water in tub. Found harness to pump is not connected. I secured connection and all water drains correctly. Test unit running a normal cycle and unit is operating as designed. No leaks present. Job complete. &172.36 c.c autho # R99NHY

"Arrived on site to inspect washer drain pump constantly on. Upon further inspection, I placed the unit in diagnostics showing error code F3E1-pressure sensor fault. Following Service Pointer W11766193, I removed and replaced the main control and calibrated the unit. Tested in diagnostics, and the unit is operating as designed. No water leaks observed during service, job completed. W11607637 No one available to sign for receipt."

"Arrived on site for unit not heating correctly. Upon arrival, performed vent test and found it was good. Inspected behind unit and found a lot of lint. Upon closer inspection of the vent hose, found some areas where the collar meets the joint that it has some exposed holes. Used silver tape to seal all openings. Tested unit and now unit is functioning as designed. No parts needed"

"Arrived on site for unit slowly producing ice. Upon arrival, customer stated the ice will stay stuck on the grid cutter and all the ice will stay in front of the bin but empty in the back. Proceeded to replace W11542867 recirc pump and W10919199 grid cutter. Tested unit and now unit is functioning as designed. Also confirmed water pressure to reservoir is good and condenser coil is clean. No water leaks detected at this time"

"Arrived on site for water leaking from icemaker. Removed upper covers found leak from corner edge of icemaker housing,ran icemaker diagnostic E2 error. Removed housing cleaned ice from housing, replaced defective icemaker,reinstalled housing,power cycled unit to erase error,ran harvest test passed,ran fill passed no leaks,drained water from icemaker ran fill test again no leaks. Installed cover upper and freezer leds not powering on,chexked voltage no DC voltage Removed freezer led module no voltage,checked each led on icemaker housing no voltage no voltage at cover harness. Ordering led control. Used w11658802; ordrng 1 W10830288 (Led control) and 1 W11753078 (Main control) and 1 W11484840 (Leds) and 1 W11483116 (Led) and 1 W11753077 (Ui)"

"Arrived on site to diagnose a unit that was tripping the breaker as soon as it was plugged in. Verified the complaint and confirmed the breaker tripped immediately upon connection. Inspected all wire connections at the terminal block and junction box wiring tested good and was properly secured. Proceeded to inspect the main control board. Disconnected the main control board and found that the breaker no longer tripped, indicating the issue was either with the board or wiring connected to it. Replaced the main control board with a new one and reconnected power. The breaker tripped again immediately. Traced the wiring harness and found damage to the main harness causing a short to ground. A new main harness will be ordered to complete the repair. Job scheduled for Friday.; ordrng 1 W11736786 (Main harness)"

Arrived on site to diagnose the unit for the left front burner not turning on fullyonly the center portion of the element was heating. Tested the unit and confirmed the issue. Inspected the burner and found the switch for the left front burner was faulty and not sending proper voltage to the outer element. Replaced the burner switch. Reassembled and tested the unit. Verified that both the inner and outer elements are now heating properly. Unit is operating as designed. Job complete.

Arrived on site for defrost timer making noise . Found belt had slipped off dampner cog. Reinstalled belt . Noise has gone away . Collected 162.36 autho UY4EC9. No water leaks detected at time of service. Job complete

"Arrived to 2605 to replace previously ordered part. Upon arrival, proceeded to replace 661570V belt. Tested unit and now unit is functioning as designed. Tenant not home. No one available to sign"

"MHW8630HC4 customers stated that wash machine was not washing properly and was shutting off and would get an s d.Error code ran diagnostics and verified suds fault code. Ran auto test and wash machine passed.All component tests on auto test. Adjusted auto dispenser to lower the amount of detergent. It dispenses. the customer has a whole house. Water filtration system, which can cause an issue with excess suds. Also advise customer to do. The clean wash cycle at least once a month due to the fact that he does a lot of laundry. Advised customer to not use the auto dispense feature due to their whole house filtration system, which is causing an excess of suds.But instead to use just about two tablespoons for a full size load, and for anything smaller than that to use about a tablespoon of soap.And that is all no leaks detected at time of service"

Arrived on site for washer MVW5430MW2 not starting kid won't lock. Inspected unit and found error code f7 e1 stored tested capacitor found bad. Replaced capacitor w11395618 and tested. Unit lid lock not locking properly replaced lid lock w11670519 and tested. Unit is now functioning properly and as designed to. No leaks present at this time job completed

"Arrived to 201 for F3E3 inlet thermistor short. Upon arrival, tenant stated they just moved in and tried 3 loads of laundry. During the 3 times, unit shut off during mid cycle within 5 to 10 minutes and displayed F3E3 code and the last cycle they done, it passed with no issues. Performed diagnostics with no issues. Ran vent test and found poor airflow with vent on. Picture attached. Removed vent hose and found airflow was good. Advised maintenance to check outside damper to make sure its not painted shut. Unit is functioning as designed. No parts needed"

"Arrived on site to inspect washer model WFW560CHW4 displaying error code F9E1 and not draining. Upon further inspection, verified the code and problem. Gained access to drain pump, removed filter, and found multiple pieces of clothing trapped, blocking water flow. Removed obstruction, reassembled, and tested washer. Washer now operating as designed. No water leaks observed during service."

"Arrived on site to inspect range oven not heating properly. Upon further inspection, I tested the oven at 350 degrees. I monitored preheat time and operating temperatures. I measured the temperatures for 4 cycles and got an average temperature of 344 degrees. I advised the customer on proper loading and preheating. The oven is operating as designed. No gas leaks observed during service."

"Arrived on site to inspect refrigerator WRS315SDHM13 noises. Upon further inspection, I found the unit operating as designed with no unusual noises being made. The customer advised that the noise gets very loud, like a loud buzzing noise. I gained access to the evaporator to find ice built up to the left of the evap fan (photo). I removed the ice and traced it back to the ice maker fill tube, which is leaking a small amount of water during the fill. I found the fill tube had an extension and a ziptie holding it in place from the manufacturer. I tested the ice maker, and when it filled, a small amount of water leaked from the bottom of the fill tube. Using some permagum from my van stock 212643, I placed a bead ar9und the fill tube to seal off the small gap and retested. The unit is operating as designed. No water leaks were observed at the end of service, job completed. 212643-van stock"

Arrived onsite KSGB900ESS5 for front left burner not igniting well. Found small simmer orifice blocked with spill over residue. Cleaned port to restore normal ignition. Explained findings to customer. Demonstrated normal ignition. No parts. Signer not available.

Cx stated unit would syart by itself or not syart at all. Ran diagnostics and found 2-1 5-1. Stuck key and door lock fault. Start button not working on console. Ordering console and door lock. W11589973 W10653840; ordrng 1 W11589973 (Control console) and 1 W10653840 (Door lock)

Arrived on site for range WFGS5030RZ0 center burner not working properly 1 year builder inspection. Inspected unit found center burner built up with grease not allowing burner to work properly. Replaced burner and tested. Unit is now functioning properly and as designed to job completed

"Arrived on site to inspect washer MVW6500MBK1 not draining. Upon further inspection, I found the unit in the garage and not connected to water or an outlet. The customer had an extension cord, and when I plugged the unit in, I placed it in diagnostics and checked error codes. I found F9E1-drain pump failure. I tilted the unit back and found the drain pump harness broken free from the connector at the pump. I removed and replaced the lower main harness and calibrated the unit, and tested (without water). The unit is operating as designed as far as I could test without water. No water leaks observed during service, job completed. W11591637"

Arrived onsite for WDP540HAMZ2 complaint of leaking when used. Found cracked tub. Ordering tub to repair. PSP item. Office to reschedule. No parts used today. ; ordrng 1 W10909756 (Dishwasher)

"Arrived on site to inspect washer WTW4816FW3 not spinning out the clothing. Upon further inspection, I placed the unit in diagnostics showing error code F8E1-long fill. Cleared the code and continued with testing, and found the cold valve is not fully opening. I removed the inlet hoses and inspected the valvd screens and found a large amount of debris in the screen on the cold valve. I removed and replaced the valve assembly and calibrated the unit. Retested, and the unit is operating as designed. No water leaks observed during service, job completed. W11210463"

"Arrived onsite apartment 103 for unit wdf332pamw0 with no power and no function. Restored function by turning the power on to the unit at the wall switch. Then tested unit, wash pump also doesn't work. Replaced pump and motor W11613570. Tested unit. Operating as designed. No leaks."

"Arrived on site for a WRS325SDHZ08 refrigerator making sounds. Found the evaporator fan had ice around it so i removed it. Freezer was at 39 degrees and the amp draw was .080 at the compressor. Customer said his ice packs have been thawing out also. I'm ordering W11580057 compressor, W11546692 evaporator, wpw10143759 dye drier, w11506635 service port, lokring and a 2 hour ss tech for the return visit. Office will need to reschedule. ; ordrng 1 W11580057 (Compressor) and 1 W11546692 (Evaporator) and 1 wpw10143759 (Dye drier) and 1 w11506635 (Service port) and 1 Lokring (Cap tube) and 1 2hoursstech (2 hour ss tech)"

"Arrived on site for refrigerator needing w10309994 compressor, w p w 10143759 u v dryer, & w1156635 access valve. On arrival confirmed issue and installed ports, then pull vacuum and recharge system with five ounces of r134a. Found even frost pattern forming an informed customers to allow twenty four hours for unit to stabilized temps, call complete."

Arrived on site to install ordered parts for a MFX2571XEM0 refrigerator. When I turned the valve behind the refrigerator it started leaking. I opened it up and it stopped leaking. I advised the customer to have the valve repaired and call us back to complete the repair. Office will need to reschedule ; O-emld tckt

Arrived on site to install ordered parts for a WOS97ES0ES01 oven. I installed the blower w11713858 and heated to 350 degrees. Unit is operating as designed.

"Arrived on site for unit shutting off every 10 minutes, tested the terminal block and discovered a loose connection. Terminal block was replaced with part# 279320 and customer was instructed to monitor the unit. Job complete."

"WTW4957PW0 Arrived on site for a washer that keeps draining. On arrival, I verified long drain a failed control board under service pointer they recommend replacing the control board.I replaced the control board, calibrated then tested product is working as its designed no water leaks visible from the main water supply."

"Arrived on site for dishwasher start button not working. Upon arrival, confirmed the start button did not work but the other buttons on the control panel were operational. Replaced the control board with part# W116834, unit is now functioning properly. Job complete."

"Arrived on site for a WRT549SZDM06 refrigerator leaking. Found the evaporator completely frozen, also a lot of ice build up in the freezer. Also found the water valve leaking. I turned the water off and dried the floor behind the refrigerator. I talked to maintenance and he's going to move the refrigerator to his shop to thaw it out. Will return with a icemaker kit w11729596 to replace the valve. ; schdld next appmnt for 10/10 FRI !"

"Arrived on sign for washer's stuck in drainloop. An arrival confirmed issue and found control board bad, it fell under sp. s153eb. I replaced w 11607637 control unit works as design call complete"

Arrived onsite for previously diagnosed part. I replaced the main harness and ran the oven to 350. Unit is now heating as designed and no errors are popping up. No leaks. Call complete. Installed W11461074 HRNS MAIN.

"MVWC465HW2 Arrived on site for a washer with pump running. On arrival, I verified the pump running. I ran diagnostic and found an error code of F3E1 a failed pressure switch. Service pointer recommends replacing the control board. I replaced the control board, calibrated then tested product is working as its designed no water leaks visible from the main water."

Arrived on WTW4850HW3 for washer pump running. I found a F3E1 pressure sensor failure present. I replaced the control W11607637 per s code S153EB and tested unit. Unit now operates as designed and no leaks have occurred. Call complete.

"WRF560SEHV00 Arrived on site for a refrigerator, making too much ice and the mullion not making contact. On arrival, I verified that the mullion had failed.I replaced the part and tested the mullion . Mullion is making contact. The icemaker was hanging, not sure how, but I reinstalled it. Nothing was wrong with the icemaker. The client thought that when it was full, it would stop on its own. I explained to the client he had to raise the lever in order to stop the icemaker from producing ice. Product is working as its designed no water leaks visible from the main water supply. Client didn't sign"

"Arrived on site for an ice machine model KUIX505ESS2 with a reported leak. Inspected the unit and work area. The customer had removed the front cover and pointed out the suspected leak area. When the water was turned on, water was found leaking from the inlet valve. Replaced the inlet valve and tested the unit. The machine filled and operated as designed with no leaks present during operation. NO WATER LEAKS OBSERVED DURING SERVICE. Call complete"

Arrived on WDT970SAHZ0 dishwasher not draining. I found the drain pump to run but no water flow coming out. I found the drain pump impeller broken. I replaced the drain pump andnunit now operates as designed. Customer informed me that the top rack was broken and I found the wheels broken. Ordering 2 W10712395 upper rack wheels. RS for 10/10/25.; ordrng 2 W10712395 (Upper rack wheels)s

"WRF555SDFZ19 Arrived on site for refrigerator not making ice. On arrival, I tested temperature in the RC 38 degrees, and the FC was -1 degrees . The temperature was great further inspection I found that the icemaker has failed ,arm was locked. I replaced the icemaker and tried to test it, but I wasn't sure how to do it on this mode .I called Whirlpool techline, case# 2104359 and they helped run a quick test on the icemaker. The product is working as its designed no water leaks visible from the main water supply. Turn off 5 seconds then on wait 10 and then push the button twice Case # 21043459"

"Arrived on site for a washing machine model MHW3505FW1 that won't start cycles. Inspected unit and work area. The customer stated that the machine will flash error codes whenever the unit won't start and that when this happens, he can wait a few minutes, and then the machine will start working. He advised that this does not happen on every cycle, but seems to be intermittent. I ran the unit through diagnostics and found an F9 E1 (long drain), F3 E1 (pressure system fault), and F8 E1 (long fill) error codes in diagnostics. I ran the init through an auto cycle and found the machine complete each step in the cycle without an issue. I checked the pressure hose and did not find it kinked. I found all electrical connections properly connected. I replaced the main control W11201284 and tested the unit. I found the unit working and operating as designed with no leaks present during operation. Call complete."

Arrived on WRFF3736SV00 for crisper door issues. I found the customer saying that there's a gap in the crisper drawer at the top. I installed the new crisper drawer and explained to the customer that the gap is normal and there's nothing wrong with the gap there as it is only a cover and not a flipper. Unit is operating and looks as designed. No leaks. Call complete. Supplied part doesn't show on service matters.

"WRF767SDHZ04 Arrived on site for a refrigerator not releasing ice. On arrival, the client stated ice was sticking together. In the top ice bin. The client wasn't aware that they had to keep a steady flow to keep ice from sticking together. I tested the despenser with a cup, and the product is working as its designed .The refrigerator has two icemakers, and they were using the bottom one more. I noticed that there was a blue piece of tape covering the laser in the top bin, that determines the level of ice, I removed it. No parts used product is working as its designed no water leaks visible from main water supply."

Arrived on MDB4949SKZ3 Dishwasher for F8E4. Customer stated it intermittently comes up. I inspected the drip pan and no water is present. When looking at the float switch is found a wire on the harness is broken. Will need to order the lower harness W11726283 for repair. RS for Thursday 10/09/25.; ordrng 1 W11726283 (HRNS Lower)

"MED4500MW0 Arrived on site for a dryer with water inside and not heating. On arrival, I tested ventilation to clients home it was in terrible condition. I recommend that the client contact a duct cleaning company. Further inspection I found a failed hi limit tstat. I replaced the part and tested without the vent on the product is working as its designed."

"Arrived on site for washing machine model MVW4505MW2 not completing cycles. Inspected unit and work area. Customer advised they ran two loads that didn't complete the spin cycle, with no water in the basket but clothes coming out soaked. Ran diagnostics and found F0 E9 (off balance pause) error code, indicating stop during off balance load. Checked suspension in good condition but machine on unlevel ground, with tub leaning against front panel. Adjusted feet to level washing machine properly. Checked basket properly secured to drive shaft. Ran diagnostic cycle; all portions working and operating as designed. Asked customer about load; they explained washing a few pairs of sweatshirts and sweatpants. Explained to customer that as a suspension-based model, light or bulky loads can cause off balance issues occasionally. No other stored error codes to cause premature shutdown, so issue tied to off balance. Reviewed loading procedures with customer. Unit working and operating as designed. Call complete. No parts installed. NO WATER LEAKS OBSERVED DURING SERVICE."

"Arrived on KRMF536RPS00 for previously diagnosed parts. I replaced the W11482384 Filter head, W11658802 Icemaker, and W10843055 CONTROL HV. I had the unit unplugged the whole time so I could do a power reset for the icemaker. Powered unit on and unit now dispenses water with the new filter installed. No leaks are present. Call complete."

"WTW6157PB0 Arrived on site for a washer stopping mid cycle. On arrival, the washer wasn't connected to a power or water source. I moved the washer to an area with water and power. I connected and tested I found control board has failed . I replaced ,calibrated, and then tested the washer started leaking from the water valves onto the carpet. I used my shop vacuum and removed water from carpet.I notified the manager on duty. I replaced the water valves and then tested again product is working as its designed with no water leaks visible from main water supply. I uploaded photos as well ."

"Arrived on site for an electric oven model WEC530H0DS0 that is not getting to proper temperature. Inspected unit and work area. The customer explained that when he turns his oven on that the oven will take longer than normal to reach preheat, and with that when he does finally reach preheat, his temperature thermometer says the unit is only at 200?F. I test the unit in diagnostics and found the bake element would not come on. I gained access to the bake element and found that the element had imploded due to a weak spot and broke, causing the issue. I replaced the bake element W10779716 and tested the machine again on a 425?F bake cycle. I found the unit it begin to work and operate as designed fluctuating between 388?F and 453?F, averaging a temperature of 420.5?F. The unit is now working and operating as designed. Call complete."

"Arrived on site to replace previously diagnosed tub nuts, installed 4 tub nuts and tested unit is now running as designed no leaks detected job complete installed 4 x W11545286"

"Electric dryer WED4850HW0. Verified no heat. Removed back panel and checked voltage at terminal block: 120V L1 to neutral, 230V L2 to neutral, 240V L1 to L2. Checked thermal fuse, high-limit thermostat, thermal cutoff, and operating thermostatall good. Heating element checked good with continuity. Replaced timer wpw10436303, but unit still would not heat. Ordering temperature switch w11661755 which has a resistor that's most likely open and causing the no-heat issue.; ordrng 1 W11661755 (Temperature switch)"

Arrived on site for front left burner not always working. Customer said she pushed it in and it worked once. Replaced receptacle for fornt left burner. Verified operation. Call complete.

"Arrived on site to test unit element issues, tested unit found missing bake element, installed element, heated unit to 500 and advised customer to keep it there for 2 hours unit is now running as designed job complete W11182108"

Arrived on site for no heat dryer . Found elemnt coli broken . Replaced heating elemnt WP8544771. Thermostats and fuse in good shape . Recommended haved exterior vents cleaned . Cleaned large amounts of lint from unit . No one on hand to sign ticket . Job complete

"Arrived on site for dishwasher, leaving streaks on the dishes. Picture taken. Entered diagnostics and found no error codes. Ran automatic test mode and all components pass. Loud noise when dispenser was activated, indicating dispenser may be going out. Lots of suds during the first test. Advised customer on soap usage. Reset for Friday am. ; ordrng 1 W11412300 (Dispenser)"

"Arrived on site to test unit for not working properly, tested unit found drain pump not turning off, inspected pressure hose and found no issues, replaced control and tested unit is now running as designed no leaks detected job complete installed W11607637"

Arrived on site for danage to the door on the inner right side panel. Confirmed damage to door panel. Removed door. Replaced outer door panel. Call complete. WPW10634271

"Arrived on site for customer complaint of unit not spinning after filling, found issue with actuator. Ordering actuator. ; ordrng 1 W10913953 (Actuator)"

"Arrived on site to test unit for not working properly, tested unit found drain pump not turning off, inspected pressure hose and found no issues, replaced control and tested unit is now running as designed no leaks detected job complete installed W11603811"

Arrived onsite for washer in 2084 model number WTW5010LW0. Foundnbroken drain harness at the molex. Repaired using the harness W11643701. Unit is now operating as designed. Advised maintenance on repair. No signer available.

"Arrived on site to test unit for not heating, tested unit found broken timer, replaced timer checked all other sensors found no issues, could not test unit out completely do to no available power connection, if the issue persists then unit will need to be installed and connected to a proper power source, at this time job complete installed W10857612"

Arrived on site for refrigerator not cooling. Also the freezer stopped making ice. Found temps at 59f and 20f. Unit looks to have a frozen over evaporator coil. Entered diagnostics and confirmed thermistor are good. Entered heater test and confirmed 122v coming into heater. Disconnected and found heater was open. Will need new heater. Office will call to schedule. Advised used customer to unplug or shut off power day before so unit can be properly serviced. ; ordrng 1 W11626107 (Heater)

"Arrived on site to test unit for not heating, tested unit found broken timer, replaced timer checked all other sensors found no issues, could not test unit out completely do to no available power connection, if the issue persists then unit will need to be installed and connected to a proper power source, at this time job complete installed W11742939"

"Arrived on site to test unit for not working properly, customer stated only some buttons work on the panel, inspected wiring did not find any loose connection but most buttons are unresponsive, replaced front panel and tested unit is now running as designed job complete installed W11177576"

"Arrived to unit 307 for unit stuck on drain mode. Upon arrival, unit was unplugged. Plugged in unit and immediately started draining. Proceeded to replace W11629601 control and made sure there are no restrictions and kinks on the pressure hose. Ran diagnostics and passed with no issues. Unit is functioning as designed. No water leaks detected at this time. Special project S153EB performed"

Arrived onsite for a control replacement with a one stop provision. Replaced the control w11548749 to repair. Unit is now operating as designed. Tested to 350f preheat. No signer available.

"Arrived on site for for downdraft not working. Upon arrival, found blower motor only working on 1 speed. Called LC and stated its either going to be the switch or the motor. Ordering W11083804 blower motor and W11690658 blower switch. Weighing call for 2 hours. No parts replaced. Office to reschedule ; ordrng 1 W11083804 (Blower motor) and 1 W11690658 (Blower switch) and 1 2hours (2 hours)"

Arrived on site for wiring harness issue on electric oven WEE515S0LS2. Removed and replaced main harness W11766509. Tested the unit and ran bake to 200 degrees; verified it's not shutting off. Unit working as designed.

Arrived onsite WRS325SDHZ14 for ice not dispensing and found ice clamped in bin. Removed clump3d ice and explained the necessity of an occasional bin refresh due to clumping. All else checks good. No parts.

"Arrived onsite WRT112CZJW01 and found compressor locked and unable to turn over. Replaced compressor W11370574, access valve W11506635, dye drier WPW10143759 and coupler W11504434. Pulled vacuum and checked joints. Charged to spec and observed for proper cooling. Unit has positive heat exchange and is beginning to cool. Advised customer onnthe repair."

Arrived on site to diagnose electric dryer WED8500DC4 making excessive noise when running. Tested unit and confirmed excessive screeching noise. Disassembled unit and found seizing tensioner pulley and two sticking rollers. Replaced tensioner pulley and rollers from repair kit 4392067. Reassembled and tested unit. Verified noise resolved. Unit working as designed and heating normally.

Arrived on site to replace console. Replaced control panel test unit and unit test good job complete.

"Arrived on site to diagnose dishwasher with the dispenser door not opening during the wash cycle. Verified the issue and proceeded to remove the front panel to inspect the dispenser assembly. Upon inspection, found the solenoid had come off the plastic tab that actuates the dispenser door. Secured the solenoid properly back onto the plastic tab and ensured it was locked into place. Reassembled the front panel and ran a full diagnostic cycle to test dispenser operation. The dispenser door now opens and closes properly during the cycle. Unit is operating as designed. Job complete."

"Arrived on site for washing machine model WTW4957PW0 not completing cycles. Inspected unit and work area. Customer advised they ran two loads that didn't complete the spin cycle, with no water in the basket but clothes coming out soaked. Ran diagnostics and found an F0 E5 (off balance load) error code. Checked suspension and found it was in good condition but machine on unlevel ground, with tub leaning against front panel. Adjusted feet to level washing machine properly. Checked basket properly secured to drive shaft. Ran diagnostic cycle; all portions working and operating as designed. Asked customer about load; they explained washing sheets, towels, and clothes together because he lives by himself and only runs the washer once a week. Explained to customer that as a suspension-based model, mixed or bulky loads can cause off balance issues occasionally. No other stored error codes to cause premature shutdown, so issue tied to off balance issue. Reviewed loading procedures with customer. Unit working and operating as designed. Call complete. No parts installed. NO WATER LEAKS OBSERVED DURING SERVICE."

"Arrived on site for customer complaint of unit running drain pump constantly. I replaced control under S153EB, calibrated and tested, unit tested good. Part used w11607637"

Arrived on site for washer WTW5010LW0 to install previously ordered part. Replaced cabinet assembly. Test unit and is operating as designed. No leaks present. Job complete

Arrived on site for left front burners having unusual flame . Burner is performing normally at time of service. Customer had video. Advised to make sure nothing is under burner caps like water of food particals . No gas leaks detected at time of service. Job complete .

"RECOMMENDED NOTE: KFIS29PBMS02: Verified waterline at isolation valve was split and leaking. Need to order water tube from isolation valve up to filter housing. Tried using PEX line and couplers, but they were the wrong size (needed 5/16' and 1/4'). Did not have the right size coupler. Ordering inlet water tube w11209890. No leaks detected during service.; ordrng 1 W11209890 (Fill tube)"

"Arrived on site for washer model number WTW4855HW3 with pump running continuously. Ran diagnostics and observed F3/E1 error code, replaced control board W116076 via service pointer S153EB. Unit is now functioning properly. Job complete. No water leaks observed during service."

Arrived on site for drain pump constantly running. Ran diagnostics and found error code f3 e1 pressure system failure. Replaced control under s code S153EB and tested. Unit is now functioning properly and as designed to. No leaks present at this time job completed

"Arrived on site to test unit WFE515S0JS4 for RF burner operating only on high. Upon arrival verified issue, burner engages solely at high setting with no variable control. Performed inspection and found the RF infinite switch shorted internally, causing continuous full voltage to the element. Prescreened switch is incorrect. Ordering correct switch to complete repair. No parts installed, no one on site for signature, rescheduled for 10/10.; ordrng 1 WP3149400 (Right front switch)"

"Arrived on site . For leaking from filter area. . Removed cover and found water leaking from housing . Ordering housing . No other leaks detected at time of service. Call, to set return ; ordrng 1 W11758337 (Filter housing) and 1 Permagum"