We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS0
Near Leander, Texas 78641
Brandon B
Job Details:
11/12/2025
Arrived on site for a dishwasher KDFM404KPS0 not draining. Found the pump was clogged so it replaced the pump/ motor w11416362. Tested in factory mode and everything is working as designed. No leaks detected.
We serviced a
WHIRLPOOL MICROWAVE
Model JMW2430LL04
Near Leander, Texas 78641
Brandon B
Job Details:
11/12/2025
Arrived on site for a oven JMW2430LL04 getting a F2E1 error. I cycled the unit but still got the error. I installed the console w11598173 and cycled it 2 times. I tested the microwave and oven. Unit is operating as designed.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Austin, Texas 78754
Justin
Job Details:
11/12/2025
Arrived on site to repair dishwasher dented front panel. Replaced panel and tested. Unit is functioning properly and as designed to. Uploaded picture on new panel onto SD. No one on site for signature job complete
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Manor, Texas 78653
Justin
Job Details:
11/12/2025
Arrived on site for drain pump constantly running. Upon arrival customer stated we already replaced control and unit is working. Verified serial numbers did not match. Maintenance said they will call it back in once they figure out we're unit is located.
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Leander, Texas 78641
Brandon B
Job Details:
11/12/2025
Arrived on site for a washer WETLV27HW3 not cycling. Found it couldn't agitate or spin. The capacitor tested bad so i installed a w11614512 capacitor. Used from 467285. Ran a factory cycle and everything is working as designed. No leaks detected while on site.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC336RPS00
Near Austin, Texas 78732
Miguel
Job Details:
11/12/2025
Arrived on site for refrigerator not making any ice. Found temp in freezer is 0f. Bucket was half full. Tested and icemaker cycled with no issues. Tested water fill and it passed and filled fine. Unit is working as designed. Advised customer this icemaker is slow. Will take 2-3 days to fill bucket. Call complete.
We serviced a
WHIRLPOOL WASHER
Model WTW4307SW0
Near Austin, Texas 78732
Miguel
Job Details:
11/12/2025
Arrived on site for washer not draining. Tub ismhalf full of water. Found display flashing f9e1. This is a long drain. Power and code do not reset. Checked at drain pump and found plastic cover broken off. Will need a new pump. Found no voltage at pump from bk/wh-bl. At control pr bk-bl=126. We will need lower harness. Use extension and supplied voltage direct to pump . Water all drained. Office will call to schedule once parts arrive. ; ordrng 1 W11782104 (Lower harness) and 1 W11741147 (Drain pump)
We serviced a
WHIRLPOOL OVEN
Model WOES3030LS01
Near Liberty Hill, Texas 78642
Brandon B
Job Details:
11/12/2025
Arrived on site for a oven WOES3030LS01 with no power. Found the breaker was tripped. Customer said that they weren't using it and it just turned off. I opened it up and checked for any visible issues. I found one of the relays wasn't seated fully. I replaced the control w11649136 and tested in bake. Amp draw is normal unit is operating as designed
We serviced a
JENN-AIR MICROWAVE
Model JMW3430LM03
Near Liberty Hill, Texas 78642
Brandon B
Job Details:
11/12/2025
Arrived on site for a oven JMW3430LM03 tripping the breaker when using the microwave. Customer said it made a pop sound near the interlocks when it tripped. Found no error codes. I heated a glass of water 2 times and ran it empty also without any issues. Also ran the oven and calibrated it while on site.
We serviced a
KITCHENAID MICROWAVE
Model KEMC378KSS04
Near Austin, Texas 78730
Miguel
Job Details:
11/12/2025
"Arrived on site for microwave light not working. Found the bulb was bad. Gave quote of 33.96 parts, 289.99 labor, total of 323.95 plus tax. On approval, I removed the oven from the wall. Replaced microwave bulb. Verified operation. Call complete $350.68. Auth code: M3K3MW"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Kyle, Texas 78640
Tim M
Job Details:
11/12/2025
"Arrived on site to test unit WTW4855HW3 for pump running. Upon arrival customer stated drain pump constantly runs unless power is removed. Applied power, drain pump immediately engaged indicating a pressure system fault. Entered diagnostics and found F3E1 (pressure system fault) error code stored. Per S code S153EB, followed TSP W11766193. Both model and serial number fall within the rework. Cleared error code and reset control, cycled power, drain pump still immediately engages. Inspected pressure hose, found no kinks, punctures or restrictions. Valve is not leaking. Pressure switch on the control has failed. Replaced control (W11607637) and applied power, drain pump no longer immediately engages. Ran a calibration cycle successfully. Unit is now running as designed, no leaks detected, job complete."
We serviced a
WHIRLPOOL OVEN
Model JOEDC730RL00
Near Santa Rita Ranch, Texas 78628
Brandon B
Job Details:
11/12/2025
Arrived on site for a oven JOEDC730RL00 tripping the breaker. I verified it tripping around 100 degrees on both ovens even though amp draw was normal. I replaced both bake elements w11545804 and tested both ovens without tripping the breaker. Safety is closed. Will call tomorrow
We serviced a
KITCHENAID RANGE
Model KFGC558JSS07
Near Round Mountain, Texas 78663
David Z
Job Details:
11/12/2025
"Arrived on site to follow up on range KFGC558JSS07 with low broil flame. Installed new gas valve W11239228 for main oven. No drastic difference in flame size noted. Reexamined broil burner orifice and replaced it with another 90 Black orifice from spare conversion kit. Reran unit; flame increased significantly, likely due to slightly off orifice drilling. Showed customer flame difference and reviewed griddle functionality. Griddle is 120v element and will not heat as fast or perform like 240v electric element in speed and intensity. Verified no gas leaks and all functions working as designed."
We serviced a
GE OVEN
Model JT5500SF6SS
Near Austin, Texas 78730
Miguel
Job Details:
11/12/2025
"Arrived on site for oven. Not running and showing f97. Ran and confirmed failure. Found lower blower motor not spinning when activated. Gave quote of 116.68 parts, 259.99 labor, total of 376.67 plus tax. Removed oven from wall. Replaced lower cooling fan. Verified operation. Call complete"
We serviced a
WHIRLPOOL VENTHOOD
Model WVW53UC6LS
Near Georgetown, Texas 78628
Lou
Job Details:
11/12/2025
"Arrived on site to inspect venthood WVW53UC6LS0 with rust. Upon further inspection, I found the back panel against the wall on the left side with rust (photo). Tested the blower and lights, and the unit is operating as designed. Contacted techline and spoke to George and advised of the complaint and my findings. George questioned how the unit filters were cleaned, and the customer advised that they clean them with water and let them dry. The customer advised that they allow the filters to dry overnight or longer, but there's no water on them when they put the filters back in place. George advised that the customer will need to clean the rust with sandpaper to keep it from spreading, and the case will not go to engineering for review as this is a cosmetic issue. George provided Case #21560409. I provided the case number to my customer and recommended that they contact customer service to discuss and provide them with the number. The unit is operating as designed, and no parts were replaced, job completed."
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Andice, Texas 78628
Lou
Job Details:
11/12/2025
"Arrived on site to inspect range WFG320M0MS0 tripping the breaker. Upon further inspection, the customer advised that the unit is not tripping the breaker anymore, but it's showing error code F1E1-main control failure. I checked for error codes in diagnostics and found the mentioned code. Cleared the code and tested it, and the unit would heat temporarily, then shut down and show the code. I removed the rear panel and found the sensor harness crimped due to being caught in between the rear panel and chassis. I tested the harness continuity and resistance and found it good, but when I moved the harness, I lost resistance. I contacted Whirlpool Safety and spoke to Lacretia and advised of my findings and recommended replacing the main control (F1E1) and the main sensor harness. Lacretia provided concession #WSJ7JQWPL1. I removed and replaced the main control and am ordering the main harness and scheduled return service for 11/17/25. No gas leaks were detected during service. W11620481; ordrng 1 W11465032 (Main sensor harness)"
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCF72DKL04
Near Austin, Texas 78737
Luis
Job Details:
11/12/2025
"Arrived on site. Nanny ket tech in,owner was busy with another contractor,diagnosed a defective filter,installed bypass good water flow. Let owner know unit will need a new filter,informed customer will need to collect service fee,customer went to bedroom to get a credit card after coming out of room customer declined to pay service fee claiming Jenn air told him it was covered,informed customer refrigerator is out of warranty and still he declined thw service fee,called office and spoke with Susie about the situation."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Bastrop, Texas 78602
Matthew
Job Details:
11/12/2025
Arrived onsite for refrigerator WRQA59CNKZ not cooling properly in RC. Customer using digital thermometer to tack and has been averaging mid to low 40's. FC is functioning properly. Used thermometer coupled to track temperature. Per service pointer customer can experience temperature that is slightly higher than set point. Pointer calls for replacement of control with updated software. Replaced control w11455229. Customer will monitor. Job complete
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Bastrop, Texas 78602
Matthew
Job Details:
11/12/2025
Arrived onsite for washer needing hub nut replacement. Replaced hub nut W10528947. Calibrated and tested. Unit is now functioning properly. Job complete
We serviced a
KITCHENAID REFRIGERATOR
Model KSRG22FKSS18
Near Austin, Texas 78758
Andrew R
Job Details:
11/12/2025
Arrived onsite for unit not cooling. Upon arrival customer stated they did a power reset and unit is cooling now. I verified temps RC at 34 and FC at -1. Temps checked good. I inspected the evaporator and found normal frost pattern. I hear the Evap fan running as designed. I cannot find an issue with the unit as after a power reset it is operating as designed and possibly a glitch in the controls. I advised customer to keep the condenser clean as there was a bit of dust on it. Unit is operating as designed during time of service. Call complete. No parts installed.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78757
Andrew R
Job Details:
11/12/2025
Arrived onsite for unit constantly draining. I found a F3E1 pressure sensor failure present and confirmed drain keeps running. Under s code S153EB I replaced the control W11607637. Unit now operates as designed and no leaks are present during time of service. Call complete.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78757
Andrew R
Job Details:
11/12/2025
Arrived onsite for unit constantly draining. I found a F3E1 pressure sensor failure present and confirmed drain keeps running. Under s code S153EB I replaced the control W11607637. Unit now operates as designed and no leaks are present during time of service. Call complete.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Austin, Texas 78759
Andrew R
Job Details:
11/12/2025
Arrived onsite for no heat. I confirmed no heat. I tested continuity on thermals and found the cutoff to be open. I replaced the cutoff and made sure element isn't grounding out. Heating element checked good. Unit is now heating as designed. Call complete. Installed 279816.
We serviced a
WHIRLPOOL REFRIGERATOR
Model ET1CHEXSB01
Near Austin, Texas 78759
Andrew R
Job Details:
11/12/2025
Arrived onsite for food thawing and freezing. I found the evaporator fan operating but found a clogged drain present. Verified defrost heater is working. I defrosted the drain and pan and unit will now cool as designed. I made customer aware that because of the ice it may drip a bit into the rc. Customer understands. Call complete. No leaks. No parts installed.
We serviced a
KITCHENAID DISHWASHER
Model KDTM405PPS1
Near Austin, Texas 78759
Andrew R
Job Details:
11/12/2025
Arrived onsite for dishwasher not washing. I heard the pump and motor run but little pressure. I found polarity and voltage correct. I replaced the pump and motor W11416362. Tested unit and now it operates as designed. No leaks sighted during repair. Call complete.
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near Austin, Texas 78729
Andrew R
Job Details:
11/12/2025
"Arrived onsite for no agitation or spin. I found the unit to spin but a shift actuator code is present. No agitation but only spin. I replaced the W10913953 SHIFT ACTUATOR, W1072967 SPLUTCH AND W11239857 BELT due to belt and cam being worn. Tested the unit and it operated as designed. No oil leaks or leaks present during service. Call complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Manor, Texas 78653
Justin
Job Details:
11/12/2025
Arrived on site for drain pump constantly running. Upon arrival escorted by maintenance found very large dog not crated or put away. Will need to reschedule and front office will have to let tenant know dog need to be put away o return visit ;
We serviced a
WHIRLPOOL RANGE
Model WFG320
Near Manor, Texas 78653
Justin
Job Details:
11/12/2025
Arrived on site for bake not working. Inspected unit cannot verify model. Serial number took a picture and uploaded it to SD. Inspected unit found igniter not igniting. Tested voltage at igniter found no voltage going to igniter. Control is not sending voltage to igniter unit will need a new control. Ordering control office to reschedule.; ordrng 1 W11620481 (Control)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Austin, Texas 78729
Andrew R
Job Details:
11/12/2025
Arrived onsite for unit constantly running. Upon arrival I found F8E4 float open. Checked underneath and found rats nest remnants and droppings. I found the rats had chewed the orange wires on the harness for the float switch. I advised customer that this repair won't be covered. I quoted customer Parts 138.84 Labor 254.99 and total 393.83+tax for the harness replacement. Customer agreed to proceed. Will need to order W11729441 HRNS-WIRE for repair and office to RS as we are showing OOS.; ordrng 1 W11729441 (HRNS-WIRE)
We serviced a
KENMORE REFRIGERATOR
Model ="106.9658184"
Near Buda, Texas 78610
Luis
Job Details:
11/11/2025
"Arrived on site for loud noise. Customer played recording of noise,power cycled unit removed evaporator cover found odd noise at evaporator fan motor compressor and condenser fan running,evaporator fan discontinued. Collected service fee of $149.99 plus tax. $162.36 CC Auth# VTFA93"
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED22TQXFW00
Near Temple, Texas 76502
Tyler
Job Details:
11/11/2025
"Arrived on site for refrigerator not cooling. On arrival, confirmed, thermostat and fans both working. I then found the compressor had a rco410 hard start and compressor is overheated, triggering the tod and failing to start. Found unit needs a sealed system repair W10309990 compressor, 876765 copper kit, wp2188822 evap coil, wpw10143759 uv dryer, w10913906 access valve. Office reschedule, once availability, if parts is known; ordrng 1 W10309990 (Compressor) and 1 876765 (Copper kit) and 1 wp2188822 (Evap coil) and 1 wpw10143759 (Uv dryer) and 1 w10913906 (Access valve)"
We serviced a
KITCHENAID RANGE
Model KOED530PSS00
Near San Marcos, Texas 78666
Tim M
Job Details:
11/11/2025
"Arrived on site to test unit KOED530PSS00 for upper oven getting too hot. Upon arrival customer stated unit reaches set temperature but continues rising and fails to regulate. Verified symptom by initiating bake cycle in upper oven and monitoring with thermocouple; unit exceeded set point without cycling indicating welded bake relay on control. Replaced Upper Oven Control Board (W11448962) and retested; temperature now regulates correctly. Advised customer to monitor performance and noted that if issue recurs, return with harness, thermostats, and UI. At the time of service unit is running as designed, job complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near San Marcos, Texas 78666
Tim M
Job Details:
11/11/2025
"Arrived on site to test unit WRF767SDHZ03 for no ice production. Upon arrival customer stated both ice makers fail to produce ice and water accumulates on the door shelf below the ice container. Entered service mode and retrieved E2 (motor lost position) error code. Executed test 57; ice maker motor did not engage. Inspected ice door and found gasket not sealing, allowing customer-added ice to melt and leak. Attempted manual cycle of FC ice maker; gears would not turn. Recommend replacing both ice maker assemblies, ice door with gasket, main control, and verifying RC ice maker housing alignment. Ordering parts, no parts installed, rescheduled for 11/17. Customer informed appointment may shift if parts dont arrive in time.; ordrng 1 W11171728 (Ice door) and 1 W11717180 (FC ice maker)"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Austin, Texas 78731
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose a dishwasher displaying an F8E4 error code, indicating water detected in the float switch area. Inspected the unit and confirmed the presence of water in the float tray. Upon further inspection, found that the water was leaking from the fill valve connections. Removed and replaced the fill valve assembly. After replacement, ran the dishwasher through a full 40-minute test cycle to verify proper operation. Observed no leaks from any connections or components during the test. Unit is now operating as designed. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Uhland, Texas 78640
Brandon
Job Details:
11/11/2025
"Arrived on site to look at model WTW4855HW3 for customer complaint of unit running drain pump constantly. I found issue was with the control board. I replaced control under S153EB, calibrated and tested, unit tested good. Part used w11607637"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Buda, Texas 78610
Brandon
Job Details:
11/11/2025
"Arrived on site to look at model WTW8127LC0 for customer complaint of unit not draining. Found error codes f6e3, f1e2, f9e1, f7e7, found gearcase oil on rotor and rotor stripped, found stator error code as well as some evidence of the lower wire harness being tampered with. Unit will need gearcase, stator, rotor, slider, clutch, and lower wire harness. ; ordrng 1 W11449841 (Gearcase) and 1 W11195971 (Stator) and 1 W11260238 (Rotor) and 1 W10734521 (Slider) and 1 W10754448 (Clutch) and 1 Cnote (Auth)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Austin, Texas 78748
Luis
Job Details:
11/11/2025
"Arrived on site for no ice. Icemaker not running through a forced harvest diagnosed a defective icemaker, replaced icemaker ran harvest test passed icemaker filled with water no leaks. W11700250"
We serviced a
MAYTAG MICROWAVE
Model mmv4205fb3
Near Lakeway, Texas 78734
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose a microwave door that was not closing properly. Upon inspection, found that the bottom door switch holder was stuck in the closed position, preventing the door latch from engaging the switches correctly. Disconnected power to the unit for safety and gained access to the switch assembly. Found the holder misaligned and not allowing the switch to operate as intended. Adjusted and secured the switch holder back into the proper open position. Reassembled the unit and restored power. Tested the microwave multiple times, and the door now closes and latches properly. Verified operation by heating a cup of water unit heated correctly with no error codes or abnormal noises. Unit is now operating as designed. Job complete."
We serviced a
KITCHENAID RANGE
Model KOES530PPS00
Near Lakeway, Texas 78734
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose an oven with blower fans that continue running even when the unit is not in use. Upon inspection, verified the complaint and confirmed that the blowers were operating constantly. Tested the temperature sensor and found it reading 75?F, matching room temperature indicating the sensor is functioning properly. Checked for stored error codes and found none. Proceeded to test the control board and discovered that the relay on the board was stuck in the closed position, continuously sending voltage to the blower fans. Replaced the control board and reassembled the unit. Tested operation by preheating the oven to 350?F, then turning the unit off to verify proper fan operation during cool down. The blower fans shut off automatically once the oven reached a safe temperature. Unit is now operating as designed. Job complete."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507ESS01
Near Driftwood, Texas 78619
Brandon
Job Details:
11/11/2025
"Arrived on site to look at model KRFF507ESS01 for customer complaint of unit leaking out of ice maker section. Found ice clumping together like it was over filling or weaping valve. I replaced valve, ran harvest and fill, checked for ice door leaks, everything passed while on site, no leaks detected after repair. Part used wpw10341329"
We serviced a
KITCHENAID OVEN
Model KOEC730SPS00
Near Manor, Texas 78653
Joe Z
Job Details:
11/11/2025
Arrived on site for oven KOEC730SPS00 with issue of not powering on. Upon arrival customer turned unit off at breaker because fan runs continuously. I restored power and fan indeed runs continuously. Also Main ACU fault appears on display and does not allow and test to be done. Customer was able to use oven a few times before issue. Need to replace control. Ordering control. Office to reschedule ; ordrng 1 W11783549 (Control)
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Georgetown, Texas 78628
Lou
Job Details:
11/11/2025
"Arrived on site to inspect dishwasher WDF330PAHS3, not drying dishes and not cleaning properly. Upon further inspection, I found the unit not installed properly as it is tilted forward. The customer advised that it hasn't leaked. I found the door gasket badly rippled on the left and right sides, and the heating element shorted/burnt on the left side. I advised the customer that with the element not heating, the dishes won't get clean or dry. I placed the unit in diagnostics showing error code F7E1-no heat. Cleared the code and continued with testing and found the unit operating as designed except for the heating element. I adjusted the tub and re-leveled it. I am ordering the element and door gasket and scheduled return service for 11/13/25. No water leaks were observed during service. ; ordrng 1 W10518394 (Heating element) and 1 W11768590 (Tub/door gasket)"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Manor, Texas 78653
Joe Z
Job Details:
11/11/2025
"Arrived on site for washer WTW8127LC1 to install previously ordered parts . Upon disassembly, found more parts needed due to rusting . Also found load and go dispenser leaking. Need to replace dispenser housing, drawer, faucet assembly, bezel, front brace, screws (6), faucet assembly, and faucet bezel, needs autho. Office to reschedule ; ordrng 1 W11413340 (Drawer) and 1 W11621181 (Housing) and 1 W11381327 (Brace) and 1 W11423773 (Top) and 1 Needautho (Need autho)"
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS12
Near Burnet, Texas 78611
Lou
Job Details:
11/11/2025
"Arrived on site to inspect microwave WMH31017HS12 light not working/unit not working. Upon further inspection, I found the unit with power as the display was lit up. When I opened the unit door, the interior light came on. I tested the unit using my microwave tester, and the unit is operating as designed. The customer advised that the venthood light doesn't work. I tested the light andmit failed to trun on. I gained access to the bulb and found the element inside was broken. I advised the customer that this bulb is not covered under their warranty as it's accessible to the customer to replace it on their own. I advised the customer that I could quote them for a bulb and order it, and the customer advised that they would purchase one on their own and replace it. Unit is operating as designed except for the venthood bulb. Job completed."
We serviced a
WHIRLPOOL OVEN
Model RBD307PVS00
Near Killeen, Texas 76542
Wesley
Job Details:
11/11/2025
Arrived onsite RBD307PVS00 for unit operating with failed bake element in upper oven. Replaced upper bake element WPW10207397. Tested oven. Unit is now operating as designed.
We serviced a
MAYTAG WASHER
Model MTW7200RR0
Near Nolanville, Texas 76559
Wesley
Job Details:
11/11/2025
"Arrived onsite MTW7200RR0 for unit operating with failed gearcase causing noises during agitation. Found play in the shaft. Ordering gearcase to repair. PSP item, office to reschedule ; ordrng 1 W11754447 (Gearcase)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC300ESS01
Near Austin, Texas 78748
Luis
Job Details:
11/11/2025
"Arrived on site for no cool. Powered unit on compressor and fans powered on,removed compressor cover let unit run found no heat of discharge tube diagnosed evaporator and compressor needed also found ripped gasket on fresh food door. Sealed system parts covered estimate for gasket and sealed system labor part $178.71 labor $734.99 plus tax. Customer will call into office if they approve repair. Collected service fee of $149.99 plus tax;$162.36 CC Auth# CW3JM3"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Belton, Texas 76513
Wesley
Job Details:
11/11/2025
Arrived onsite for WDP540HAMZ4 with faulty power block connection. Repaired by securing wiring connection. Unit is now operating as designed. No parts. Advised customer on repair.
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFF507HPS02
Near Austin, Texas 78745
Luis
Job Details:
11/11/2025
"Arrived on site for no ice. Ran diagnostic E2 error diagnosed a defective icemaker,replaced icemaker and fill tube heater reassembled,power cycled unit ran harvest test passed ran fill test passed no errors. W11658802,w11087201"
We serviced a
MAYTAG DRYER
Model MED8630HC2
Near Austin, Texas 78738
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose a dryer not heating. Verified the complaint by running the unit and confirming no heat output. Disassembled the unit by removing the top panel, front panel, and drum to access the heating element and all related sensors. Tested the high-limit thermostat, thermal cutoff, and thermistorall components tested within proper range. Inspected the heating element and found it broken, causing the no-heat condition. Provided the customer with a repair quote for replacement of the heating element, which the customer approved. Installed the new heating element, reassembled the unit, and tested operation. Verified that the unit is now heating properly and cycling as designed. Unit test good. Job complete. Part $118.42 labor $214.99. $360.92 CC Auth# 9UKHU4"
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Belton, Texas 76513
Wesley
Job Details:
11/11/2025
Arrived onsite WFES3530RS0 for unit with tripped breaker. Tested oven and found unit did not trip during battery of tests. Performed burnoff procedure and set up to bake at 500f for 3hrs. Unit is operating as designed. No parts.
We serviced a
WHIRLPOOL DRYER
Model WED8000DW4
Near Austin, Texas 78737
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose a dryer making a squeaking noise during operation. Disassembled the unit completely to gain access to the idler pulley and drum support rollers. Upon inspection, found the idler pulley not spinning freely and beginning to seize, causing the squeaking sound. Also found the support rollers showing signs of wear.Replaced the dryer repair kit, which includes the idler pulley, drum support rollers, and belt. Reassembled the unit and ran a full test cycle. Verified that the dryer is now operating quietly and smoothly. No abnormal noises present at this time. Job complete."
We serviced a
WHIRLPOOL RANGE
Model WFES3030RS0
Near Jarrell, Texas 76537
Wesley
Job Details:
11/11/2025
"Arrived onsite for oven tripping breaker WFES3030RS0, heat treated unit with burnoff procedure. Unit heating 500f for 3hrs on bake. Observed proper function for 40 minutes. Called to make report to whirlpool safety. Reported findings. No further actions required. Sr#21510694"
We serviced a
WHIRLPOOL OVEN
Model WFES3030RS0
Near Jarrell, Texas 76537
Wesley
Job Details:
11/11/2025
"Arrived onsite for range tripping WFES3030RS0, commenced needed burnoff. 3hrs at 500f. Unit is now operating as designed. Not tripping while onsite. No parts"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Georgetown, Texas 78628
Brandon B
Job Details:
11/11/2025
"Arrived on site for a dishwasher KDTM604KPS0 getting a stuck float error. Also found a open valve error. I ran in factory mode and couldnt replicate the issue. Unit is washing and draining as designed. I quoted for a new valve. 70.72 parts, 229.99 labor and a total of $325.52 with taxes. Customer approved so I replaced the valve and tested again. Unit is operating as designed. No leaks detected while on site $325.52 CC Auth# Y9P3UX"
We serviced a
WHIRLPOOL WASHER
Model WTW8500BW0
Near Georgetown, Texas 78626
Brandon B
Job Details:
11/11/2025
Arrived on site for a washer WTW8500BW0 not draining. I tested the resistance to the drain pump and got 16 ohms. Checked for voltage to the pump in test mode and got nothing. The control is discontinued sothis machine cant be serviced. Collected the service fee $162.36 CC Auth# 9FWRJK
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM08
Near Georgetown, Texas 78626
Brandon B
Job Details:
11/11/2025
Arrived on site for a refrigerator WRS331SDHM08 not dispensing water. I verified the issue and checked for voltage at the valve. I replaced the valve w11645245 but still getting very little water. I replaced the housing w11162042 and now it's getting water as it should. No leaks detected while on site
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Pflugerville, Texas 78660
Andrew P
Job Details:
11/11/2025
"Refrigerator KRMF706ESS01. Customers stated that the deli drawer displays stopped working after they defrosted the refrigerator and the freezer door was not closing properly. Previous technician had removed the door and rails, finding the deli drawer had 2 broken wires in the harness and was full of blue liquid, which caused the wires to corrode and the deli control to fail. Gave customer estimate on replacing the door; customer declined repair. Removed freezer door and rails, reinstalled rails and door. Freezer door now opens and closes properly and does not slide off track. Refrigerator is working as intended. No leaks at time of service."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ4
Near Pflugerville, Texas 78660
Andrew P
Job Details:
11/11/2025
"7-1 4-3 2-1 Dishwasher model WDT540HAMZ4. Customer stated that the dishwasher would fill but would not wash. Ran diagnostics and found wash motor fault code. Ran dishwasher and it filled but did not wash. Verified open winding on motor. Removed and replaced wash motor W11613479. Tested dishwasher and it filled, washed, and drained. No leaks detected time of service."
We serviced a
AMANA WASHER
Model NFW5800HW4
Near Pflugerville, Texas 78660
Andrew P
Job Details:
11/11/2025
"NFW5800HW4. Customer stated they have an extended warranty. Customer showed me her warranty information through Amanda. I advised the customer that she needs to contact her extended warranty company to dispatch a service request. Otherwise, I cannot service the washer until that is done. Customer understood and said they will contact their extended warranty company. NO WATER LEAKS OBSERVED DURING SERVICE"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Round Rock, Texas 78665
David Z
Job Details:
11/11/2025
"Arrived on site to diagnose dishwasher WDT730HAMZ1 with dead start button. Tested unit and confirmed start is only non-functional button. Requires control replacement W11683480. Corrected engineering digit from 0 to 1, which did not match control on ticket. Ordered correct control for engineering digit. Return visit set for 11/13. NO WATER LEAKS OBSERVED DURING SERVICE.; ordrng 1 W11683480 (Correct Control)"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Pflugerville, Texas 78660
Andrew P
Job Details:
11/11/2025
Washer WTW4855HW3: Verified pressure switch fault. Removed and replaced control board w11607637. Recalibrated unit; washing machine is functioning properly. Unit falls under S code for pressure switch fault; repair authorized. NO WATER LEAKS OBSERVED DURING SERVICE. Nobody available to sign invoice.
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Waco, Texas 76712
Jonathan M
Job Details:
11/11/2025
"A broad downside for a washing machine model WTW7120HW0 that is leaking from the gear case and as a cracked tub. Inspected unit and work area. The customer advised that they already had another company come out, who advised that they were getting water and oil leaking from the gear case and from the tub due to a crack. They also explained that the tub most likely cracked because of bad suspension i did confirm all the customers' complaints and attempted to remove the agitator. I found the agitator completely seized onto the drive shaft and could not be removed. The unit will need a full rebuild for repair, including basket, tub, agitator, spanner nut, drain filter, gearcase, slider, rotor, and suspension. The office will need to get authorization due to high cost of repair and if authorization is given, contact the customer about a return date due to several out of stock and PSP items. No parts were installed and no leaks were detected during service. ; ordrng 1 W11178227 (Basket) and 1 W11551646 (Spanner nut) and 1 W11219115 (Tub) and 1 Drainfilter and 1 WP8533928 (Filter screw)"
We serviced a
WHIRLPOOL DRYER
Model WED8500DC4
Near Round Rock, Texas 78664
David Z
Job Details:
11/11/2025
"Arrived on site to diagnose dryer WED8500DC4 that had 2 complaints: Timed does not seem like it's drying fully, and normal cycles seem to get too hot and don't stop when they are supposed to. Checked errors and found F4E4, F4E3, F2E1. Based on the one airflow code, I did recommend an annual vent cleaning. For the stuck key error, I am ordering and replacing the console. I ran temp checks and found unit is not overheating and it is cycling properly. I did find eco boost was on with normal cycles. I recommend disabling the eco boost. I could not find or verify any other mechanical failures, and could not duplicate any timed dry issues. Temps are cycling and averaging about 160-170 in the center of the drum. Office to schedule when parts arrive, and we are to replace the console and control. ; O-emld tckt"
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HZ09
Near Pflugerville, Texas 78660
Scott
Job Details:
11/11/2025
Arrived on site for some of the buttons on control panel not working . Found connection on control board for UI ribbon not making good conection on ribbon. Replaced control and all buttons are now functioning properly. Job complete
We serviced a
WHIRLPOOL WASHER
Model WTW5020SW0
Near Temple, Texas 76502
Tyler
Job Details:
11/11/2025
"Arrived on site for washer, needing w11130362 suspension rods. On arrival confirmed issue and installed part, then tested washer and found no leaks and squeaky noise removed, call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Austin, Texas 78723
Scott
Job Details:
11/11/2025
"Arrived on site for warmer then normal temps periodically. Ran temp checks . Temps are normal. At time of service . No frost build up. Normal frost pattern on evap. All fans working getting properly . When running compressor test relay would click several times before compressor would kick on . Compressor pulling .89 amps . Ordering start relay and cap. Also ordering perma gum , drain tube starting to drop a bit . Not causing any air leaking but to prevent future issues . No water leaks detected at time of service. Return set for 11/13.; ordrng 1 W11615506 (Start relay) and 1 WPW10350564 (Cap) and 1 Permagum"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS2
Near Austin, Texas 78756
Scott
Job Details:
11/11/2025
Arrived on site for dishwasher door flopping open . Found latch holding spring had come off . Spring still in place . Reattached latch . Tested door . All checked normal. Door staying in place . No parts needed . Labor 189.99. Collected 205.66 autho V9Y4M4. Job complete
We serviced a
WHIRLPOOL MICROWAVE
Model WMMF5930PB00
Near Austin, Texas 78750
Miguel
Job Details:
11/11/2025
Arrived on site with parts ordered. Removed microwave from over range. Replaced vent motor. Verified operarion. Call complete.
We serviced a
MAYTAG DISHWASHER
Model MDB7749SBM3
Near Round Rock, Texas 78681
Daniel A
Job Details:
11/11/2025
Arrived on site to install previously diagnosed and ordered part per previous technician. I installed the upper and lower spray arms and advised the customer of properly loading and detergent and rinse aid usage. No water leaks observed during service. WPW10082841 WPW10330588.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Austin, Texas 78704
Matthew
Job Details:
11/11/2025
"Arrived on-site for dishwasher model WDT730HAMZ1 still running after cycle is completed. Ran diagnostics and found no stored error codes. Ran test and found customer was experiencing the fan running, unit has fan drying technology. Unit is functioning properly. Job complete"
We serviced a
ROPER REFRIGERATOR
Model RT18BKXKQ00
Near Killeen, Texas 76542
Robert
Job Details:
11/11/2025
"RT18BKXKQ00 Arrived on site for a refrigerator not cooling in either compartment. On arrival, I verified that it was no cool. I didn't hear the compressor on, so I pulled it out and installed my personal start device it kicked on I took amp it was 3.8 before it cup off . A sealed system repair is needed for the repair. I ordered the compressor, evaporator, start device, and access valve. Compressor is a R134A 3 hours for repair will be needed returning parts just in case needed. Office, please reschedule as soon as possible. ; ordrng 1 W10309988 (Compressor) and 1 WP2263920 (Evaporator) and 1 Wpw10143759 (Uv drier) and 1 W11506635 (Access valve) and 1 Threehours (Three hours needed for repair)"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Pflugerville, Texas 78660
Andrew P
Job Details:
11/11/2025
Washer WTW4855HW3: Verified pressure switch fault. Removed and replaced control board w11607637. Recalibrated unit; washing machine is functioning properly. Unit falls under S code for pressure switch fault; repair authorized. NO WATER LEAKS OBSERVED DURING SERVICE. Nobody available to sign invoice.
We serviced a
MAYTAG DRYER
Model MED6230RHW3
Near Round Rock, Texas 78665
David Z
Job Details:
11/11/2025
"Arrived on site to diagnose electric dryer MED6230RHW3 making noise when spinning. Tested the unit and confirmed a high-pitched grinding sound after a few minutes. Disassembled unit and checked for broken blower wheel. Found outer rim cracked, causing the noise. Replaced blower wheel with new blower wheel WP697772. Tested unit and verified proper operation."
We serviced a
WHIRLPOOL WASHER
Model WTW4307SW0
Near Lakeway, Texas 78734
Brandon
Job Details:
11/11/2025
"Arrived on site to look at model WTW4307SW0 for customer complaint of unit not filling properly. I entered diagnostic mode and found no error codes. Ran a diagnostic test cycle, unit passed diagnostic test cycle. Ran a test cycle on bulky and max fill, showed customer"
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW1
Near Austin, Texas 78734
Brandon
Job Details:
11/11/2025
"Arrived on site to look at model for customer complaint of lid locked and unit not draining. Found issue with lower harness, I replaced harness but lid would not unlock. I replaced lid lock and tested, control would not reset. Parts used w11643701, w11627413 and w11670519 lid lock and service covered under warranty. Quoted customer for control and harness $492.25 i replaced control, unit tested good. Collected payment on cc. $516.86 CC Auth# Y94RFP"
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS3
Near Austin, Texas 78741
Brandon
Job Details:
11/11/2025
Arrived on site at apartment 535 to look at model WEE515S0LS3 for customer complaint of unit tripping the breaker. Found ground and neutral tied together causing unit to trip the breaker as soon as I plugged unit in. Instructed customer to call an electrician. Called safety to document Case number 21506730
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78744
Brandon
Job Details:
11/11/2025
"Arrived on site at apartment 2201 for customer complaint of drain pump running constantly. Found issue with the control board. I replaced control under S153EB, calibrated and tested, unit tested good. Part used w11607637"
We serviced a
WHIRLPOOL WASHER
Model WFW6620HW0
Near Austin, Texas 78756
Scott
Job Details:
11/11/2025
Arrived on site for washer flashing LOC and suds . Found control locked . Control would not unlock. Did breaker reset . Controls would unlock . Got unit into diagnostics. Got Suds error code . Ran test 12 . All checked normal. . Instructed on auto load and adjusting soap concentrations. Also on control lock feature . Collected 162.36 autho 3UFC4N. No water leaks detected at time of service
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM12
Near Georgetown, Texas 78626
David Z
Job Details:
11/11/2025
"Arrived on site for follow-up on refrigerator WRS315SDHM12 not freezing. Found unit short cycling and not staying on more than 3 minutes. Checked thermistors; RC thermistor resistance was 11.2K (roughly 25 degrees per tech line). Noted thermistor not snapped into diffuser. Removed diffuser, which was broken and required replacement. Thermistor was in FC tunnel, not plugged into diffuser as required. Installed new W11380595 air diffuser and W11546690 thermistor control, attaching thermistor to proper location. Unit cooled properly; compressor stayed on. Repair completed. NO WATER LEAKS OBSERVED DURING SERVICE. W11380595, W11546690"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78744
Brandon
Job Details:
11/11/2025
"Arrived on site at apartment 6305 for customer complaint of drain pump running constantly. Found issue with the control board. I replaced control under S153EB, calibrated and tested, unit tested good. Part used w11607637"
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Taylor, Texas 76574
David Z
Job Details:
11/11/2025
"Arrived on site to diagnose washer MVW7232HW2 with F2E2 error. Examined and confirmed error. Customer said they got a load done with no error, but it came back again the next load. Error is for a disconnected HMI. Removed the console and reseated all ribbon cable connections on the console. When unit was plugged back in, the control never came back on. Installed new control W11687817 and tested again. This time unit came on and let me start a load. Instructed customer to run a couple loads and let us know if error returns. Should it return, we need to return with a new UI/Overlay. Repair completed. No water leaks found."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Taylor, Texas 76574
David Z
Job Details:
11/11/2025
"Arrived on site to diagnose washer MVW7232HW0 giving F8E1 error with oily substance underneath. Examined unit: cold side of valve slow to fill, needs valve replacement; extreme gearcase oil splattered underside, requires gearcase; gearcase leak caused fluid and rust on rotor, stator, clutch, and slider, all scraping/making noise and need replacement. Suspension worn, causing excessive basket bouncelikely root cause of failures. Washplate seized during removal attempt. Due to multiple failures and seized parts, recommend full inner assembly rebuild with new tub and basket. Called Third Party Team for large parts need, reported under case 21502434. Instructed to bill diagnostic; third party will contact extended warranty for direction. Closing call. NO WATER LEAKS OBSERVED DURING SERVICE. Homeowner not on site to sign ticket. ; O-emld tckt"
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Austin, Texas 78748
Matthew
Job Details:
11/11/2025
"Arrived onsite for range WFES3530RS0 , Light not coming on. Inspected and found light rod switch not connected. Secured rod and tested. Unit is now functioning properly. Job complete"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Austin, Texas 78748
Matthew
Job Details:
11/11/2025
"Arrived onsite for dishwasher WDF341PAPM2, door falling down. Inspected and found Only right side failed. Spring was overextended and broke bushing. Replaced right side, spring wpw10337934 (1) and bushing wp8268990(1). Unit is now functioning properly. Job complete"
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Austin, Texas 78748
Matthew
Job Details:
11/11/2025
Arrived on-site for dryer WED500cmW0 not turning on. Inspected and found unbalanced power supply. L1 has 0volts and L2 has 209 volts. Notified builder that an electrician would be needed to resolve the issue.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Austin, Texas 78748
Matthew
Job Details:
11/11/2025
Arrived on-site for dishwasher WDF341PAPM2 damaged panel. Took pics. Panel is ordered. Office to reschedule ; O-emld tckt
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Austin, Texas 78748
Matthew
Job Details:
11/11/2025
"Arrived onsite for range WFES3530RS0 , Light not coming on. Inspected and found light assembly needed replacement. Replaced w11707255. Replaced and tested. Unit is functioning properly. Job complete Light assembly w11707255 from 467023."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78748
Matthew
Job Details:
11/11/2025
Apartment 12112. Arrived onsite for washer WTW4855HW3 drain pump running continuously. Found unit had f3e1 pressure system failure. Covered under scode S153eb. Replaced control board w11607637. Calibrated and tested. Unit is now functioning properly. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Austin, Texas 78749
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose dishwasher not washing dishes properly. Upon inspection, verified the unit was filling with water but the wash motor was not circulating water through the spray arms. Checked voltage at the motor and confirmed the motor was receiving correct voltage but not activating. Removed the old sump and motor assembly and installed a new replacement assembly. Reassembled the unit and ran a full test cycle. Verified proper operationunit is now filling, washing, draining, and drying as designed. No leaks observed during operation. Job complete."
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GPS0
Near Sunset Valley, Texas 78745
Leonardo
Job Details:
11/11/2025
"Arrived on site to diagnose a dishwasher leaking issue. Inspected and ran the unit through a wash cycle to locate the source of the leak. Found water leaking from the diverter motor area on the sump assembly. Removed the old sump and motor assembly and installed a new replacement assembly. Ensured all hoses and electrical connections were secured properly. Reassembled the unit and ran multiple test cycles to verify operation. Confirmed the unit is now filling, washing, and draining correctly with no leaks present at this time. Left the old part with the customer. Job complete."
We serviced a
WHIRLPOOL RANGE
Model WFES3030RS0
Near China Spring, Texas 76633
Jonathan M
Job Details:
11/11/2025
"Arrived on site for electric range model WFES3030RS0 tripping the breaker. Inspected unit and work area. The customer advised intermittent tripping issues off and on for several months. Gained access to wiring and components; found no arcing, grounded wiring, pinched wires, or trip indicators. Replaced bake element (W10856603) and broil element (W11182108), then reassembled unit. Removed ground wire and ran unit to 500?F; amp draw from back was 15.7 amps max during preheat. Called Whirlpool safety team and spoke with Monica (SR# 21216685). Advised no burning or grounded parts; unit pulls no more than 17 amps on preheat. Confirmed GFCI breaker unchanged. Monica advised this is a breaker issuecustomer needs electrician to contact breaker manufacturer for replacement recommendations, not same type as previously done by the last electrician. Instructed no further repair at this time; issue is electrical supply, as all pertinent machine-side parts addressed. No parts installed. Call complete."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ1
Near China Spring, Texas 76633
Jonathan M
Job Details:
11/11/2025
"Arrived on site for dishwasher model WDT750SAKZ1 flashing F8 E4 (float switch open) error code. Inspected unit and work area. Customer reported running a load that did not finish and flashed the error; new cycles would not continue. Accessed float switch underneath and found suds residue in the tray. Confirmed all connections seated properly and ran diagnostic cycle. Found no leaks present during operation and confirmed suds buildup inside midway through cycle. Cycle completed without leaking water into float switch tray or underneath unit, indicating oversudsing issue. Asked customer about prewashing; she washes but does not rinse dishes, adding soap residue before using pods. Explained that this causes too much soap and reviewed proper loading and detergent procedures. Unit working and operating as designed. Call complete. No parts installed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHV02
Near Whitney, Texas 76692
Jonathan M
Job Details:
11/11/2025
Arrived on site for a refrigerator model WRX986SIHV02 that is not making ice. Inspected unit and work area. I found temperatures in the freezer at -1?F and the refrigerator section at 35?F. I found temperature setting were at 0?F and 34?F. I ran the unit through diagnostics and found the icebox fan running but running slowly. I found the icemaker showing no stored error codes. I checked the return air chamber from the icemaker at the freezer and found no ice build up or blockage in the air return. I also found no evidence of any defrost issue in the freezer. I went ahead and replaced the ice box fan W10846539 and icemaker W11658802 and tested the unit. The unit began to work and operate as designed. Call complete. No leaks were detected during service.
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EHL02
Near Austin, Texas 78756
Matthew
Job Details:
11/11/2025
"Arrived on site to perform tech line recommendations. Started by flushing system with nitrogen. Then proceeded to replace compressor, drier, 3-way valve and access port. Pulled vacuum and charged per spec. Unit began cooling. Advised customer to give 24-48hrs to stabilize. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Whitney, Texas 76692
Jonathan M
Job Details:
11/11/2025
"Arrived on site for washing machine model WTW8127LW1 turning off intermittently and prompting to refill the dispenser. Inspected unit and work area. Customer stated the machine prompts to fill detergent every cycle; they don't use the load and go dispenser as it uses too much soap. They noted the UI sometimes shuts off and restarts mid-cycle but the machine continues working, and it may turn on/off when starting. Checked voltage to the user interface console and found proper levels. Tested unit multiple times but could not replicate failure. Ran diagnostic cycle and heard tapping noise during spin. Inspected underneath and found improper screw on rotor, causing wobble due to insufficient grip on gearcase. Customer confirmed warranty tech was sent months ago to address this. Replaced user interface console W11478525 and slider W10734521. Unit then operated as designed. NO WATER LEAKS OBSERVED DURING SERVICE. Call complete."
We serviced a
WHIRLPOOL WASHER
Model WTW5105HC3
Near Austin, Texas 78717
Miguel
Job Details:
11/11/2025
"Arrives on site for washer making a noise. Customer said it was good for a few days then started making the noise. Entered diagnostics and found no faults. Ran automatic cycle, heard the clicking noise when actuator was energized. Replaced actuator."
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Austin, Texas 78717
Miguel
Job Details:
11/11/2025
Arrived on site for dryer still making the noise. Confirmed noise is coming from motor. Blower does not seperate from the motor. Replaced blower and motor. Verified operation. Call complete. W11549461
We serviced a
KITCHENAID COOKTOP
Model KCGD500GSS00
Near Austin, Texas 78717
Miguel
Job Details:
11/11/2025
Arrived on site with parts ordered. Removed cooktop. Replaced manifold with all new burner valves and ignition harness. Replaced burner knobs. With top off i tested and sprayed for leaks. No gas leaks working as designed. Put unit back together. Now back left burner does not stop clicking after it's on. Advised customer whe. I sprayed for leaks the switch got wet. Allow 24-48 hours to dry. If problem continues then a new ignition harness is needed. Call complete.
We serviced a
WHIRLPOOL RANGE
Model WFE775H0HZ5
Near New Braunfels, Texas 78130
Andrey
Job Details:
11/11/2025
"Arrived on site to test unit for tripping breaker, tested unit found unit tripping during preheat, inspected elements and found they have the silicone wedges, per service pointer replaced both elements and control, and tested unit is now running as designed, customer stated that breaker is getting replaced as well today and he will complete the burn off then, at this time job complete installed W11536793, W10779716, W11321472"