Service History 2232

Near Round Rock, Texas 78665

Nathaniel B.

Job Details: 04/16/2018

Model WMH31017FS0, Arrived on call for control panel broken and not able to mount and interior light flickers intermittenly when opening and closing door, replaced control panel and interlocks and switches and tested and all checks good, call complete.

Near Austin, Texas 78757

Cliff

Job Details: 04/16/2018

Maytag washer MVWX655DW1. Arrived on site to diagnose a washer that is not cycling properly. Found capacitor not plugged in from factory causing motor not to run and washer to error out of cycle. Wired capacitor properly and tested unit. Found all is working properly at this time. No leaks were found at time of service.

Near Temple, Texas 76502

Dona

Job Details: 04/16/2018

Arrived on site for no heated dry, found element open. Replaced heating element. Verified all water connections dry. Ran through cycle to verify no leaks and heater operational.

Near Cedar Park, Texas 78613

Jerry C.

Job Details: 04/16/2018

WDT970SAHZ0 Arrived to inspect dispenser issue. I found the dispenser door had failed and required dispenser replacement. The top rack stops were missing and require replacement. Operational test good, no leaks observed during service.

Near Austin, Texas 78704

Connor M.

Job Details: 04/16/2018

WTW4815EW whirlpool washer Arrived on site to test unit for not completing cycle. Found error code for oversudsing condition. Unit is in a retirment home, used daily with bulk powedered soap. Instruct on proper soap usage and clean cycle. No leaks detected.

Near Leander, Texas 78641

Lou

Job Details: 04/16/2018

arrived on site for loose cooktops knob. Upon further inspection, I found that the knob is working as designed, but the knob bezel was loose. The adhesive was no good. Office to order bezel and scheduled return service for 04/19 CS.

Near Leander, Texas 78641

Lou

Job Details: 04/16/2018

arrived on site for washer not distributing enough water. Upon further inspection, I played the unit in diagnostic mode and tested. Unit operated as designed with normal water flow, proper agitation and spin and the drain pump worked properly. Found that the tub was not centered; therefore, I centered it. Advised the customer on proper detergent and softner use. No water leaks observed during service.

Near Austin, Texas 78704

Connor M.

Job Details: 04/16/2018

WTW7000DW1 whirlpool washer Arrived on site yo test unit for not rinsing clothes. Customer provided pciture of white residue on clothing. No stored error codes. Instruct on try a new soap, and using proper volume of soap along with minimizing extra wash products. Unit working properly, no leaks detected.

Near Belton, Texas 76513

Dona

Job Details: 04/16/2018

Arrived on site for no operation in left oven, but left oven would control right side of oven. Performed hard reset on breaker. Reset unit, went through diagnostics found no errors. Both ovens are now heating correctly and performing with right controlling right side and left controlling left side. Temperatures checked good. Customer had stated that there had been power surges when this happened.

Near Round Rock, Texas 78664

Jonathan S

Job Details: 04/16/2018

Whirlpool venthood model# WVU37UC0FS. Making loud noises.

Near Austin, Texas 78737

Connor M.

Job Details: 04/16/2018

PYE2300AYW maytag dryer Arrived on site to test unit for not starting. Found bad thermal fuse. Replaced and tested unit. Found door switch sticking sometimes. Replaced door switch as well. Unit working proeprly at time of service. Made customer aware of proper venting and fire hazard.

Near Austin, Texas 78729

Cliff

Job Details: 04/16/2018

Maytag dryer MEDB835DW4. Arrived on site to diagnose a dryer that is making unusual noises when running. Found idler pulley and rollers squeaking when unit is operating. Replaced idler pulley and roller due to failed bearing assemblies. Tested unit and found all is working properly at this time.

Near Kempner, Texas 76539

Mike G.

Job Details: 04/16/2018

WEE510S0FS1, Arrived on site for unit will not power on checked unit and found that outlet at the wall is not getting 240v found that the from L1 to N is getting 120v from L2 to N getting less than 20v customer will need to have a Electrician to repair

Near Kempner, Texas 76539

Mike G.

Job Details: 04/16/2018

Near Leander, Texas 78641

Cliff

Job Details: 04/16/2018

Kenmore washer 11027342600. Arrived on site to replace drain pump for leaking washing machine. Replaced drain pump and tested unit. Found all is functioning properly at this time. No leaks were found after services were performed.

Near Kyle, Texas 78640

Brandon

Job Details: 04/16/2018

Arrived on site for part hanger of fresh food fan motor, I replaced fan motor, unit tested good, also updated the software, unit tested good. Water lines were dry at time of service.

Near New Braunfels, Texas 78130

Connor M.

Job Details: 04/16/2018

WCG51US0DS00 whirlpool cooktop Installed burner caps. Unit working properly.

Near New Braunfels, Texas 78130

Connor M.

Job Details: 04/16/2018

WRF989SDAE00 whirlpool refrigerator Arrived ons ite to install filter head for leaking. Installed and tested unit. Unit working properly, no leaks detected. If leak persists customer will need to relace filter as that is the only variable remaining. Job completed.

Near Austin, Texas 78745

Luis

Job Details: 04/16/2018

Refrigerator-remolded freezer door gasket adjusted middle divider and added adhesive to corner gap

Near Austin, Texas 78745

Luis

Job Details: 04/16/2018

Refrigerator-remolded freezer door gasket adjusted middle divider and added adhesive to corner gap

Near Austin, Texas 78741

Luis

Job Details: 04/14/2018

Refrigerator-installed bail arm to icemaker

Near Austin, Texas 78734

Luis

Job Details: 04/14/2018

Refrigerator-installed updated evaporator, compressor and filter drier

Near Georgetown, Texas 78633

Lou

Job Details: 04/13/2018

arrived on site for small burner not igniting. Upon arrival, I tested the unit and the unit operates as designed. I notified the customer and advised him of my findings. The customer shortly arrived and I instructed him on the use and operation of the unit. Not gas leaks detected during service.

Near Harker Heights, Texas 76548

Dona

Job Details: 04/13/2018

Arrived on site for long dry times, found ducting clogged and full of water. Removed vent from back of unit-checked temps all temps checked good. Customer will have ducting cleaned before using.

Near Temple, Texas 76501

Mike G.

Job Details: 04/13/2018

MVWB835DC3, Arrived on site to install new gearcase checked unit after repair and unit is no longer making noise checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time....

Near Temple, Texas 76501

Mike G.

Job Details: 04/13/2018

Near Round Rock, Texas 78664

Lou

Job Details: 04/13/2018

arrived on site to install previously diagnosed and ordered part. Removed and replaced the warmer element. Tested unit and unit tested good. Job completed.

Near Horseshoe Bay, Texas 78657

Thomas L.

Job Details: 04/13/2018

Arrived on site for poor washability. Second visit found drying agent dispenser leaking causing excessive sudsing thus poor washability. Replace dispenser. All water connections were dry. Offered customer a. 10% discount Callie processed card for me via phone.

Near Round Rock, Texas 78664

Lou

Job Details: 04/13/2018

arrived on site for ice maker only making crushed ice. Customer advised that she found that the ice was blocking the shoot and causing it to not dispense. The ice in the bin appeared good and there was no condensation ice buildup in the bin. Instructed customer on UI operation. No water leaks observed during service.

Near Round Rock, Texas 78664

Lou

Job Details: 04/13/2018

Near Horseshoe Bay, Texas 78657

Thomas L.

Job Details: 04/13/2018

Arrived on site for no ice condition. Found that the condenser fan motor has failed. Removed and replaced. All water connections were dry.

Near Horseshoe Bay, Texas 78657

Thomas L.

Job Details: 04/13/2018

Arrived on site for no ice condition. Found that the condenser fan motor has failed. Removed and replaced. All water connections were dry.

Near Round Rock, Texas 78664

Lou

Job Details: 04/13/2018

arrive on site for microwave not heating. Upon further inspection, I saw where the unit had damage on the right rear corner and took a snap pic. I tested the unit by placing a cup of water into the unit for 30 secs. Water did not heat. I removed and replaced the magnetron, diode, and capacitor. I tested the unit with a cup of water and the water was hot. Job completed.

Near Hutto, Texas 78634

Nathaniel B.

Job Details: 04/13/2018

Model WTW5000DW1, Unit came with home unit has a 1 yeat extended warranty through the builder, Arrived on call for unit will not drain, and stopped working after filled with water,, found that belt came off again, found that gearcase shaft has droped down more than 1/2 inch and is leaking water down the shaft of gear case, and belt has damage to it and cam is damaged, replaced cam, gearcase, and belt and checked operation of unit and no error codes and ran calabration after and then filled tub up past the agitator and found no leaks from gear case or machine after repair, call complete.

Near Hutto, Texas 78634

Nathaniel B.

Job Details: 04/13/2018

Near Wimberley, Texas 78676

Connor M.

Job Details: 04/13/2018

WRF757SDEM01 whirlpool refrigerator Arrived on site to install freezer door for cosmetic issue. After inspecting new door; installed it. Unit working properly, no leaks detected.

Near Round Rock, Texas 78681

Cliff

Job Details: 04/13/2018

Whirlpool dryer WED5000DW2. Arrived on site to diagnose a dryer with a door that will not close properly. Tested unit and found left side hinge missing a screw causing misalignment of the door. Replaced screw with one from personal stock and tested unit. Found all is functioning properly at this time.

Near Wimberley, Texas 78676

Connor M.

Job Details: 04/13/2018

RTW4640YQ1 roper washer Latch-63.43 TL190-159.99 arrived on site to test unit for not starting cycle, and sometimes not completeing cycle. Found error code for lid lock failure. Ran diagnostic test and was unable to get passed step one due to lock failure. Ordering for return. Sw approved 4/20 collected svc via check

Near Marble Falls, Texas 78654

Thomas L.

Job Details: 04/13/2018

Arrived on site for upper rack issues. Found upper rack falling forward due to failed stops. Replaced and tested. All water connections are dry

Near Wimberley, Texas 78676

Connor M.

Job Details: 04/13/2018

MDB7749SBM3 maytag dishwasher Panel-174.87 labor-149.99 arrived on site to test unit for not starting at times. Fiund failed console. Console sent is black. This unit is silver and stainless. Ordering correct part for return. Jordan approved 4/20. Colletced svc via check

Near Temple, Texas 76501

Dona

Job Details: 04/13/2018

Arrived on site for no ice production, spoke to tech line found bin thermostat faulty. Recirculating pump is not continuous flow. AHS will need to research for bin thermostat. Showing as discontinued. Callie assisted with parts. All water connections dry.

Near Highland Haven, Texas 78654

Thomas L.

Job Details: 04/13/2018

Arrived on site for leaking condition. Tested unit. Found that the drain hose was leaking. Corrected leaking condition and all operations are now normal and connections are all dry.

Near Hutto, Texas 78634

Nathaniel B.

Job Details: 04/13/2018

Model WEG745H0FS0, Arrived on call for left rear burner will not ignite, found the right rear and left rear burner caps were swaped which would not allow burners to light correctly, put burner caps on correct burners and tested and all checks good, no parts needed, call complete, customer says bill them they will contact whirlpool due to they were not instructed on customer instructs were not covered by whirlpool, customer will call whirlpool to try to get a pl1, no gas leaks at time of call. Customer will be billed service fee of 99.99 plus tax which =108.24

Near Hutto, Texas 78634

Nathaniel B.

Job Details: 04/13/2018

Near Austin, Texas 78728

Cliff

Job Details: 04/13/2018

Whirlpool microwave WMH32519HZ1. Arrived on site to diagnose a microwave with a damaged door. Found microwave door scratched and tops intersection of stainless steel. Replaced microwave door and tested unit. Found all is functioning properly at this time.

Near Dripping Springs, Texas 78620

Connor M.

Job Details: 04/13/2018

WTW7300DW1 whirlpool washer Arrived on site to test unit for no fill/ long fill. Found water getting to valves but valve not opening. Replaced valve assy and tested unit. Unit working properly, no leaks detected.

Near Kingsland, Texas 78639

Thomas L.

Job Details: 04/13/2018

Arrived on site for no ice conditions. Found the freezer at 0° and the fresh food section at 39° found power to icemaker but icemaker will not cycle. Removed and replaced ice maker. All water connections were dry.

Near Temple, Texas 76501

Dona

Job Details: 04/13/2018

Arrived on site for unit not spinning the water out of clothes, found unit with f51 error which is a motor error. Found bolt that holds rotor to bearing and stator had come loose. Retightened ran unit through entire quick wash fully loaded with clothing. Unit ran through entire cycle no errors, clothes spun out completely. Customer stated there was water under the unit after last load. Checked all water connections was not able to find any water leaks on unit. all water connections dry.

Near Temple, Texas 76501

Dona

Job Details: 04/13/2018

Case#7721741177 spoke with J.K. Arrived on site for priming noise throughout cycle. Found that the unit is now hooked to water noise has reduced. Cycles are predetermined with turning the valve on and off throughout cycle. No way to reprogram to turn off valve completely. All water connections dry. Venting clear. Unit is working per mfg specifications.

Near Dripping Springs, Texas 78620

Connor M.

Job Details: 04/13/2018

KDTE204ESS3 kitchenaid dishwasher Arrived on site to test unit for not drying dishes. Customer is using rinse aid. Confirmed function of heating element. Found customer usually does a load before bed and sometimes doesnt get a chance to unload until later the next day. This can cause water that remains on roof of unit after cycle along with water that condenses there due to cold counter tops to drip back down on dishes when left untouched for too long. Instruct customer on using delay cycle option to decrease length of time dishes remain in unit after cycle is completed. Unit working properly, no leaks detected.

Near Georgetown, Texas 78628

Lou

Job Details: 04/13/2018

arrived on site for dishwasher not cleaning well. Upon arrival, customer advised that he dishes were not getting clean. I ran unit through diagnostics and no codes appeared. During test mode, I opened the unit door and found large amounts of soap suds. Also found that the middle and lower wash arms had large amounts of debris in the ports. Cleaned out most of the debris and quoted the customer for the middle wash arm $38.42 and for the lower wash arm $64.94 and labor/service $139.99... Total $263.43. Customer agreed to pay for service fee $108.24 and advised that they would contact the office if they did not want the replacement arms. Remaining balance is $155.19. No water leaks observed during service.

Near Round Rock, Texas 78665

Nathaniel B.

Job Details: 04/13/2018

Model WTW57ESVW1, Arrived on call for cloths not spinning all the water out, installed parts previous tech ordered and all checks good, unit is draining and spinning as it should and is filling properly, call complete, no water leaks at time of call.

Near Round Rock, Texas 78665

Nathaniel B.

Job Details: 04/13/2018

Near Temple, Texas 76501

Dona

Job Details: 04/13/2018

Near Manor, Texas 78653

Joseph C.

Job Details: 04/13/2018

MDB8979SFZ2 Arrived on site for “broken control panel” complaint. Inspected unit and found notch in control panel. Removed and replaced panel. Tested unit. Unit tests good. No leaks detected, at time of service.

Near Manor, Texas 78653

Joseph C.

Job Details: 04/13/2018

Near Austin, Texas 78726

Luis

Job Details: 04/13/2018

Refrigerator-replaced freezer door

Near Round Rock, Texas 78664

Mike C.

Job Details: 04/13/2018

Whirlpool microwave WMH31017FS0 Arrived to install new magnetron, capacitor, diode and mounting hardware. Drilled stripped mounting bolts out and gained access to interior of microwave. Installed new parts and checked operation, checked good.

Near Burnet, Texas 78611

Thomas L.

Job Details: 04/13/2018

Near Burnet, Texas 78611

Thomas L.

Job Details: 04/13/2018

Arrived and replace both rails as bearing were falling out. Unit now operates correctly.

Near Lorena, Texas 76655

Mike G.

Job Details: 04/13/2018

KRFF507EWH01, Arrived on site for unit has a dent on freezer door checked unit and found that the dent is no freezer door replaced door and name plate checked unit and umit checked fine at this time.... checked unit for water leaks and no leaks found at time of srv....

Near Lorena, Texas 76655

Mike G.

Job Details: 04/13/2018

Near Round Rock, Texas 78665

Nathaniel B.

Job Details: 04/13/2018

Model RH2330XJB3, Arrived on call for fan motor is extremely loud, found that shaft in motor dropped down and allowed the fan blade to rub on the grease filter will need motor kit, per jordan motor has parts lablor and service coverage it is still with in the one year from previous repair for the motor which is covered, no charge to the customer, installed motor kit, call complete.

Near Round Rock, Texas 78665

Nathaniel B.

Job Details: 04/13/2018

Near Austin, Texas 78737

Brandon

Job Details: 04/13/2018

Arrived on site for washer not advancing after start up. I put unit into diagnostic test cycle, found cold side fill valve was slow filling, I cleaned out fill valve, put unit into calibration, and another test cycle. Unit tested good.

Near Troy, Texas 76579

Mike G.

Job Details: 04/13/2018

WTW5000DW1, Arrived on site to install new motor and cap recalibrated unit after repair and tested unit and unit is now working properly checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....

Near Troy, Texas 76579

Mike G.

Job Details: 04/13/2018

Near Georgetown, Texas 78628

Lou

Job Details: 04/13/2018

arrived on site for dryer not working. Upon further inspection, I found that the motor was not engaging and unit shut off. After a few minutes, i tested the unit again and the unit turned on. I found that the belt is fraying and the wheels were very dirty and will need to be replaced. Office to order motor, blower wheel, and dryer kit. The dryer kit will need to be installed first and unit tested as the motor may not be needed. Office to schedule return service..04/18 CS. Customer is not available that day and requested the 19th. Lint cleaned during service.

Near Temple, Texas 76501

Dona

Job Details: 04/12/2018

Arrived on site for LF error. Unit ran through 3 full cycles with no LF. Customer ran 5 different loads after that and unit did LF in different parts of cycle. Replaced faulty valve and pressure hose to correct LF. Ran through full cycle bulky/ normal unit did not give LF error. Customer will monitor. All water connections dry.

Near Pflugerville, Texas 78660

Nathaniel B.

Job Details: 04/12/2018

Model MVWC565FW0, Arrived at 10:54 am and unit was not axcessable, returned at the end of day, Arrived on call for previous diag. And function found that has failed is water valve on hot side, replaced water valve, unit is ready for resale, unit is not connected to water, call complete.

Near Pflugerville, Texas 78660

Nathaniel B.

Job Details: 04/12/2018

Near Georgetown, Texas 78628

Jonathan S

Job Details: 04/12/2018

Whirlpool washer model #WTW5000DW1. Not completing cycle.

Near Burnet, Texas 78611

Thomas L.

Job Details: 04/12/2018

Arrived on site for no ice condition. Found icemaker to have a defective drive Motor. Replaced and tested. Water connections were dry. Customer I needs to correct very low water pressure to unit.

Near Austin, Texas 78744

Luis

Job Details: 04/12/2018

Refrigerator-remolded freezer door gasket

Near Bruceville-Eddy, Texas 76524

Dona

Job Details: 04/12/2018

Arrived on site for chirping noise throughout wash, found rotor loose on stator causing noise. Suspension good, no errors. All water connections dry. Ran through full normal cycle-with no abnormal noises. Agitate sounds correct, spin smooth.

Near New Braunfels, Texas 78130

Connor M.

Job Details: 04/12/2018

WRF767SDEM00 whirlpool refrigerator Arrived on site to test unit for making too much ice. Found ice level arm not attached to icemaker at pivot point. Corrected issue and tested unit. Instruct on proper use and care. Unit working properly, no leaks detected.

Near Temple, Texas 76502

Lou

Job Details: 04/12/2018

arrived on site for sheet stuck in washer. Upon further inspection, I found that a sheet was caught/stuck under the agitator. I removed the agitator and removed the sheet and found that the agitator had plastic pieces broken on the bottom. I installed a new agitator and ran the unit in diagnostic mode. The unit read error codes F3e2, f7e8, f7e2, f0e4. Cleared the codes and continued with test mode and unit tested good. No error codes and no water leaks observed.

Near Round Rock, Texas 78681

Jonathan S

Job Details: 04/12/2018

Whirlpool gas cooktop model# GLT3657RB01.

Near Austin, Texas 78748

Luis

Job Details: 04/12/2018

Refrigerator-replaced thermistor assembly

Near Buda, Texas 78610

Connor M.

Job Details: 04/12/2018

GI6SARXXF05 whirlpool refrigerator RF360-169.99 icemaker-94.99 arrived on site to test unit for not making ice. Found icemkaer heating element failed causing ice to remain fused to mold during harvest. Found model number on record is incorrect. Ordering correct icemaker for return. Jordan approved 4/16 collected svc via cc

Near Temple, Texas 76501

Dona

Job Details: 04/12/2018

Arrived on site for unit not spinning clothes at end of cycl, found shifter error shifter not engaging. Replaced shifter and calibrated unit checked good. All water connections dry.

Near Harker Heights, Texas 76548

Steve C.

Job Details: 04/12/2018

Near Spring Branch, Texas 78070

Daniel A.

Job Details: 04/12/2018

KUDE40FXPA4 Leaking water during use. Outlet tub clamp hose separated from sump. Replaced with new clamp. Checked water inlet and drain hoses. No leaks detected. Ran wash cycle. Normal operation after service

Near Belton, Texas 76513

Lou

Job Details: 04/12/2018

arrived on site for washer not turning on. Customer advised that she ran the unit and while draining, the unit shut off and will not turn on. Unit was unplugged upon arrival. I plugged the unit in and received no power to the unit. I installed a new control and the unit came on. Placed the unit in manual test mode to drain the water and the drain pump sounded as if was dragging. I removed and replaced the drain pump and tested the unit in diagnostic mode. Unit operated as designed. No water leaks observed during service. I instructed the customer on proper detergent and softner use.

Near Austin, Texas 78704

Joseph C.

Job Details: 04/12/2018

KDTE104ESS3 Arrived on site for “not draining/control panel error” complaint. Inspected unit and found shorted power wires had blown control. Removed and replaced control. Repaired short in junction box. Tested unit. Unit is performing as designed. No leaks detected, at time of service.

Near Austin, Texas 78704

Joseph C.

Job Details: 04/12/2018

Near Burnet, Texas 78611

Thomas L.

Job Details: 04/12/2018

Arrived on site for water leaking into fresh food section. Found the defrost drain line had frozen. Defrosted and tested.

Near Burnet, Texas 78611

Thomas L.

Job Details: 04/12/2018

Arrived on site no ice condition. Found unit to have any evaporator leak. Unit also had a defective condenser fan motor. It also had a defective recirculation pump. Replaced all and tested well.

Near Austin, Texas 78749

Connor M.

Job Details: 04/12/2018

MEDX655DW1 maytag dryer Arrived on site to install drum for failure. Installed and tested unit. Unit working properly. Made customer aware of proper venting and fire hazard. Returning failed drum to storage.

Near Temple, Texas 76502

Dona

Job Details: 04/12/2018

Arrived on site for light staying on constantly unless bulb removed. Found interlock switches causing flicker replaced secondary and primary. Unit no longer flickers. Relay on control 7104 is stuck will not allow for light to turn off. Replaced control and UI light shuts off all functions check good.

Near Austin, Texas 78737

Luis

Job Details: 04/12/2018

Refrigerator-replaced icemaker

Near Austin, Texas 78748

Connor M.

Job Details: 04/12/2018

WED4815EW1 whirlpool dryer Arrived on site to test unit for noise during use. Completely dissasembled dryer at front and back. Nothing unusual found. Ran dryer without drum and had no noise. After reassembling unit making sure to tighten every screw very well i still had the same noise. Observed drum while operating by jumping door switch and found some wobbleing at drum. Ordering drum for return.

Near Austin, Texas 78757

Nathaniel B.

Job Details: 04/12/2018

Model MGD5500FW0, Arrived on call for dryer not heating and vents have been cleaned, know unit is not turning on at all, installed ui and then checked for error codes and got f6e1 which is a communication error between ui and acu, f2 e1 which is a stuck key error, f3 e6 moisture senser open, f4 e3 restricted air flow vent is cleared and ui has been replaced due to burn mark on the control and all errors but the moisture senser error, went to main control on p13 and checked ohms and got open moisture senser, called office and spoke to jordan and office will contact customer on monday about service fee due to found a functional issue with the machine that would effect dry times, per sarah will reschedule with moisture senser on 4/16/18, dryer vent has been cleaned.

Near Austin, Texas 78757

Nathaniel B.

Job Details: 04/12/2018

Near Temple, Texas 76502

Dona

Job Details: 04/12/2018

Arrived on site to check for resale, found all components ohm correctly, no structural or cosmetic damage, unit holds water. No power cord available. Unit checks to spec per ohm checks and no leaks found. Unit does not look to have been run at all.

Near Austin, Texas 78749

Luis

Job Details: 04/12/2018

Refrigerator-installed a uv drier recharged system

Near Hutto, Texas 78634

Jonathan S

Job Details: 04/12/2018

Kitchen Aid dishwasher model # KDTM354DSS4. Not cleaning dishes and leaving soap film on dishes.

Near Austin, Texas 78748

Connor M.

Job Details: 04/12/2018

MHWE201YW00 maytag washer Arrived on site to test unit for not unlocking or starting cycles, and banging noise during use. Found error code f3e2 indicating failed temp thermistor. Will return with shocks incase needed after running test. Sw approved 4/18

Near Austin, Texas 78746

Luis

Job Details: 04/12/2018

Refrigerator-installed updated ice door and motor

Near Belton, Texas 76513

Lou

Job Details: 04/12/2018

arrived on site for no water in dishwasher. Upon further inspection, I placed the unit in diagnostic mode and tested. No water entered the unit. Due to this being a new home and new construction in the area, I disconnected the water line and flushed it out. Small amounts of debris was in the line. Reconnected the water line and placed unit in test mode and unit operated designed. Water pressure at the outlet seemed high. I checked the water pressure and it was at 80psi. No water leaks observed during service. Instructed customer on detergent use and care for the unit.