Near Wimberley, Texas 78676
Connor M.
Job Details:
05/21/2018
GHW9300PW4 whirlpool washer Arrived on site to test unit for error code f06 and stopping at beginning of cycle. Found tachometer on motor worn out. Replaced motor and tested unit. Unit working properly, no leaks detected.
Near Troy, Texas 76579
Steve C.
Job Details:
05/21/2018
Near San Marcos, Texas 78666
Daniel A.
Job Details:
05/21/2018
WFW8540FW1 Baffles on tub coming loose due to heater coming out of support bracket. Replaced outer tub/basket assembly. Checked suspension/water inlet/drain hoses. Ran wash cycle. Normal operation after service
Near Killeen, Texas 76549
Dona
Job Details:
05/21/2018
Arrived on site for no heat, found open thermal cutoff, found ducting will need to cleaned in wall as it is preventing air flow. Replaced thermal cutoff. Verified operations. Temperatures check good.
Near Austin, Texas 78731
Cliff
Job Details:
05/21/2018
Whirlpool washer WTW5000DW1. Arrived on site to diagnose a washing machine that is wrinkling clothing. Tested unit and found no mechanical failures at this time. Insured unit was fully leveled and balanced. Calibrated unit to ensure proper load sizes were registered when washing. Advised homeowner on proper loading techniques and cycles to use for best performance and to prevent unnecessarily tangling and wrinkling of clothing. No leaks found at time of service and no further repairs are needed at this time.
Near Wimberley, Texas 78676
Connor M.
Job Details:
05/21/2018
WTW7040DW1 whirlpool washer Valve-152.89 TL270-159.99 arrived on site to test unit for lf error. Fiund cold water valve getting voltage but not opening. Replaced valve assy and tested unit. Unit working properly, no leaks detected. Collected balance via cc.
Near Salado, Texas 76571
Dona
Job Details:
05/21/2018
Arrived on site for no cool in ff or freezer section, found aftermarket start device has been added to unit. Start device is faulty. Wires spliced to make start device work by previous company. Will need wire harness, capacitor, start device and authorization for repair. All water connections dry. Discussed with Chase. Office will reschedule.
Near Austin, Texas 78725
Joseph C.
Job Details:
05/21/2018
ADB1400AGS1 Arrived on site for “door not latching” complaint. Inspected unit and found striker not engaging latch. Striker sticking straight out. Adjusted striker to mate with latch. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, Texas 78745
Leonardo
Job Details:
05/21/2018
Whirlpool range model: WFC310S0ES0 no display. Arrived on site to test unit for display not showing all the number. Found bad board replaced board test unit and unit test good job complete all number working correctly.
Near Austin, Texas 78745
Leonardo
Job Details:
05/21/2018
Whirlpool range model: RF365PXKW0 Arrived on site to test unit for no display on board but burner work. Test unit and found bad board replace board test unit and unit test good job complete oven and burner working correctly.
Near Salado, Texas 76571
Dona
Job Details:
05/21/2018
Arrived on site for left hand door million not always closing correctly, replaced black mullion. Verified operations on door, checked temperatures all parms check good. All water connections dry.
Near Belton, Texas 76513
Mike G.
Job Details:
05/19/2018
MEDX655DW1, Arrived on site for timer not working on automatic dry checked unit and found that the timer will work on timed dry with no issues and on automatic dry timer will not work unit just keeps going with out heating properly unit will need time and timer control to repair checked and cleaned out all lent found from unit ordering part and office will r/s customer
Near Belton, Texas 76513
Mike G.
Job Details:
05/19/2018
MEDX655DW1, Arrived on site for timer not working on automatic dry checked unit and found that the timer will work on timed dry with no issues and on automatic dry timer will not work unit just keeps going with out heating properly unit will need time and timer control to repair checked and cleaned out all lent found from unit ordering part and office will r/s customer
Near Waco, Texas 76706
Mike G.
Job Details:
05/19/2018
NED4655EW1, Arrived on site for unit not heating chcked unit and found that the vent hose from wall to unit is damaged and found that the element is shorted out replaced element and checked and cleaned out all lent found from unit and checked unit after repair and unit has good air flow with out vent hose hooked up and unit is now heating and talked to customer about replacing vent hose and not using unit until vent hose is replaced unit checked fine at this time....
Near Waco, Texas 76706
Mike G.
Job Details:
05/19/2018
NED4655EW1, Arrived on site for unit not heating chcked unit and found that the vent hose from wall to unit is damaged and found that the element is shorted out replaced element and checked and cleaned out all lent found from unit and checked unit after repair and unit has good air flow with out vent hose hooked up and unit is now heating and talked to customer about replacing vent hose and not using unit until vent hose is replaced unit checked fine at this time....
Near New Braunfels, Texas 78132
Connor M.
Job Details:
05/19/2018
MVWB725BW0 maytag washer Arrived on site to test unit for noise during operation. Found failed bearings. Will need call weighed. Office to schedule directly. Allow 2 hours
Near New Braunfels, Texas 78132
Connor M.
Job Details:
05/19/2018
KBFN506ESS00 kitchenaid Arrived on site to test unit for popping noise on right hinge. Found screw on bushing arm loose. Corrected issue and tested unit. Unit working properly. No leaks detected.
Near Waco, Texas 76710
Mike G.
Job Details:
05/19/2018
JDB9800CWX2, Arrived on site to install new control panel and checked unit after repair and all keys are working properly and unit is filling washing and draining and element is heating checked unit for water leaks and no leaks found at time of srv...
Near Waco, Texas 76710
Mike G.
Job Details:
05/19/2018
JDB9800CWX2, Arrived on site to install new control panel and checked unit after repair and all keys are working properly and unit is filling washing and draining and element is heating checked unit for water leaks and no leaks found at time of srv...
Near Temple, Texas 76504
Mike G.
Job Details:
05/19/2018
MEDE300VF0, Arrived on site to install new control checked and cleaned out all lent found from unit and tested unit and unit is now starting up and is now heating unit checked fine at this time....
Near Temple, Texas 76504
Mike G.
Job Details:
05/19/2018
MEDE300VF0, Arrived on site to install new control checked and cleaned out all lent found from unit and tested unit and unit is now starting up and is now heating unit checked fine at this time....
Near Taylor, Texas 76574
Nathaniel B.
Job Details:
05/18/2018
Model WTW6800WW1, Arrived on call for door lock error after installing control and key pad prior due to f2 el error du error , replaced door lock and tested and all checks good, no water leaks at time of call, call complete.
Near Taylor, Texas 76574
Nathaniel B.
Job Details:
05/18/2018
Model WTW6800WW1, Arrived on call for door lock error after installing control and key pad prior due to f2 el error du error , replaced door lock and tested and all checks good, no water leaks at time of call, call complete.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model WOD51EC0AS05, Arrived on call for oven temp not with in range, checked for error codes and found none,preheated ovens to 350 degrees, upper oven cut out temp is 401 , cut in is 337 degrees which is a average temp of 369 so calibrated upper oven -15 for a average temp of 354 degrees, lower oven cut out temp is 400 degrees, cut in temp is 337 degrees which is a average temp of 369 degrees which will calibrate lower oven -15 for a average temp of 354 when set at 350 degrees, no parts needed, call complete.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model WOD51EC0AS05, Arrived on call for oven temp not with in range, checked for error codes and found none,preheated ovens to 350 degrees, upper oven cut out temp is 401 , cut in is 337 degrees which is a average temp of 369 so calibrated upper oven -15 for a average temp of 354 degrees, lower oven cut out temp is 400 degrees, cut in temp is 337 degrees which is a average temp of 369 degrees which will calibrate lower oven -15 for a average temp of 354 when set at 350 degrees, no parts needed, call complete.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model WRS315SDHM00, Arrived on call for inner door is warped and is not allowing the door to seal and gasket will not even go in channel of the door to seal, see pic, ordering freezer door and grey gasket freezer, office will reschedule with customer door orders take up to 6-8 weeks.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model WRS315SDHM00, Arrived on call for inner door is warped and is not allowing the door to seal and gasket will not even go in channel of the door to seal, see pic, ordering freezer door and grey gasket freezer, office will reschedule with customer door orders take up to 6-8 weeks.
Near Copperas Cove, Texas 76522
Dona
Job Details:
05/18/2018
Arrived on site for long dry times and clothes feeling damp, found dryer is running to spec temperatures check good timer advancing, customer needs to have duct work cleaned. All ops on dryer check good.
Near Austin, Texas 78717
Lou
Job Details:
05/18/2018
arrived on site to inspect dishwasher door hitting against one side. Upon further inspection, I found that the unit needed to be leveled for the door to close properly. I found that the floor under the unit was not level as there was a large amount of tile that had been removed and the right leg was not touching the floor but the left leg was touching a piece of the tile. I found a broken piece of tile under the unit and placed it under the right leg and leveled the unit. I tested the unit and the unit tested good. I instructed the customer on proper detergent use and the amount to use. No water leaks observed during service.
Near Austin, Texas 78717
Lou
Job Details:
05/18/2018
arrived on site to inspect dishwasher door hitting against one side. Upon further inspection, I found that the unit needed to be leveled for the door to close properly. I found that the floor under the unit was not level as there was a large amount of tile that had been removed and the right leg was not touching the floor but the left leg was touching a piece of the tile. I found a broken piece of tile under the unit and placed it under the right leg and leveled the unit. I tested the unit and the unit tested good. I instructed the customer on prop
Near San Marcos, Texas 78666
Connor M.
Job Details:
05/18/2018
MVWB855DC3 maytag washer Arrived on site to test unit for leaking. Fiund no signs of leaks. Ran full diagnostic and inspected entire unit. No signs of leaks. Unable to duplicate issue. Requested customer provide more details if possible should this occur again. Unit working properly, no leaks detected.
Near Killeen, Texas 76549
Dona
Job Details:
05/18/2018
Arrived on site to replace ff thermistor, and control, replaced control and thermistor, cleared drain tubing, unit was dripping allowing for flow. Put tool through to ensure drain hose was clear. Unit is flowing. Frost pattern looks good. Unit is cooling. Operations check good. All water connections dry.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model WDF520PADB7, Arrived on call for dishes not drying, replaced control and heater element and checked operation know heater is pulling 8 amps on black wire at front bottom of dishwasher which is good, instructed customer on running hot water at sink before starting dishwasher and correct soap and rinse aid use and cleanings of dishwasher again, all checks good, call complete, no water leaks after repair.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model WDF520PADB7, Arrived on call for dishes not drying, replaced control and heater element and checked operation know heater is pulling 8 amps on black wire at front bottom of dishwasher which is good, instructed customer on running hot water at sink before starting dishwasher and correct soap and rinse aid use and cleanings of dishwasher again, all checks good, call complete, no water leaks after repair.
Near San Marcos, Texas 78666
Connor M.
Job Details:
05/18/2018
WRS571CIDM01 whirlpool refrigerator Arrived on site to test unit for ice build up not allowing auger to rotate. Found seperator not sealing well. Coupling on ice been damaged. Ordering for return. Ja approved 5/22
Near San Marcos, Texas 78666
Connor M.
Job Details:
05/18/2018
WRF993FIFM00 whirlpool refrigerator Installed evap cover and control after defrosting unit. Unit working properly, no leaks detected.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model JS48PPDBDA, Arrived on call for noise from unit and fridge and freezer not cooling, found compressor is bad has no heat exchange from discharge line and both compartments are at 95 degrees, also has noise coming from condenser fan motor, found that compressor is showing nla, will only charge the customer svc fee of 79.99 plus tax 6.60 which = 86.59, customer will contact whirlpool due to from entitlement shows a extended warranty and customer will reset up the call under the extended warranty psa look at entitlement has numbers for psa., found that sealed system parts are covered under manufactures warranty but noy labor, labor bi480 1,199.99, customer will contact whirlpool for extended warranty to see if labor and condenser fan motor can be covered under extended warranty. Office to reschedule with customer on extended warranty, customer will contact us when call is set up.
Condenser fan motor WP61005323
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/18/2018
Model JS48PPDBDA, Arrived on call for noise from unit and fridge and freezer not cooling, found compressor is bad has no heat exchange from discharge line and both compartments are at 95 degrees, also has noise coming from condenser fan motor, found that compressor is showing nla, will only charge the customer svc fee of 79.99 plus tax 6.60 which = 86.59, customer will contact whirlpool due to from entitlement shows a extended warranty and customer will reset up the call under the extended warranty psa look at entitlement has numbers for psa., found that sealed system parts are covered under manufactures warranty but noy labor, labor bi480 1,199.99, customer will contact whirlpool for extended warranty to see if labor and condenser fan motor can be covered under extended warranty. Office to reschedule with customer on extended warranty, customer will contact us when call is set up.
Condenser fan motor WP61005323
Near Austin, Texas 78759
Cliff
Job Details:
05/18/2018
Whirlpool refrigerator WRS588FIHV00. Arrived on site to diagnose a refrigerator with slow flow through water dispenser. Tested unit and found faulty filter installed and filter housing causing low flow, as flow is fine with no filter installed. Advised customer water filters are consumable items and not covered under manufacturer warranty. No other failures are found at this time and all is working properly.
Near Johnson City, Texas 78636
Robert
Job Details:
05/18/2018
Maytag washer
Near Round Rock, Texas 78664
Nathaniel B.
Job Details:
05/18/2018
Model WDF320PADB3, Autho. WERPOEREPL1 ,Arrived on call for dishes not drying, found that heating element is coming on at 8 amps and then checked incoming water temp at sink and will not go above 110 degrees after running hot water for more than 5 min, customer to contact plumber to have water temp increase dishwasher must have 120 degree incoming temp, also customer must run hot water at sink before starting dishwasher and verified that customer is using the correct amount on soap and rinse aid, no parts needed, no water leaks at time of call, call complete.
Near Round Rock, Texas 78664
Nathaniel B.
Job Details:
05/18/2018
Model WDF320PADB3, Autho. WERPOEREPL1 ,Arrived on call for dishes not drying, found that heating element is coming on at 8 amps and then checked incoming water temp at sink and will not go above 110 degrees after running hot water for more than 5 min, customer to contact plumber to have water temp increase dishwasher must have 120 degree incoming temp, also customer must run hot water at sink before starting dishwasher and verified that customer is using the correct amount on soap and rinse aid, no parts needed, no water leaks at time of call, call complete.
Near Killeen, Texas 76543
Dona
Job Details:
05/18/2018
Arrived on site for left front burner element is snapped apart, receptacle is burned apart and arched to chassis. Unit is staying on when in off position, will need infinite switch as well. Unit is in poor condition. Not normal wear and tear. Will need authorization to repair unit for this issue. Took pictures. Customer is still using unit. Tech turned breaker off and advised not to use as it is a safety hazard. Tech did tape live wires so not touching chassis. Unit is in off position.
Near Georgetown, Texas 78628
Jerry C.
Job Details:
05/18/2018
WRV986FDEM01 Arrived to instal parts. I removed replaced the fan and adapter and noted the housing was not correctly mounted. I found the doors mis-aligned and corrected. I squared the cabinet and corrected a top-forward lean. The lower left door hinge was bent down and causing the ice bin gasket to insufficiently contact the ice maker housing fascia. I was able to correct the alignment and found the gasket contact greatly improved. I corrected a top-out lean of the fc door. Operational test good, no leaks observed during service.
Near Austin, Texas 78717
Lou
Job Details:
05/18/2018
arrived on site to inspect ice maker not working. Upon further inspection, I found a large block of ice buildup on the Evap cover. I advised the customer that they would need to defrost the unit before I could move forward with inspection. I advised the customer of the waiver of damages while defrosting the refrigerator and the customer signed the waiver. I explained to the customer that they would need to defrost the refrigerator at least 24 hours before I returned. I advised the customer to lay some towels all around the unit to soak any water spillage and if they have a wet vac to keep it handy in case there was a large amount of water. Office to order Evap cover and Evap motor assembly. I will return with pre-diagnosed parts and office scheduled return for 05/25/18 SW. No water leaks observed during service.
Near San Marcos, Texas 78666
Connor M.
Job Details:
05/18/2018
WRF535SWHZ00 whirlpool refrigerator Arrived on site to test unit for water spraying from ice maker. Found icemaker mold heater not coming on. Cobes built up eventually clogging fill tube. Will need ice maker for repair. Ja approved 5/22
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/18/2018
Model KRSC503ESS01, Arrived on call for ice maker only making 2 batches of ice in 24-48 hours, checked all switches and sensors and icemaker harvested and filled with water, called whirlpool tech line and talked to tj, file number 7722025007, and was instructed to install the ui today and let customer run the unit for 24 hours and see if ame issue and if issue returns will need the main control, called shana and was insteucted to reschedule for 5/24/18 and have customer call office if issue is the same on Tuesday or Wednesday and if ice production is good to cancel service on rues. Or wed., will order ui and main control, no water leaks at time of call.
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/18/2018
Model KRSC503ESS01, Arrived on call for ice maker only making 2 batches of ice in 24-48 hours, checked all switches and sensors and icemaker harvested and filled with water, called whirlpool tech line and talked to tj, file number 7722025007, and was instructed to install the ui today and let customer run the unit for 24 hours and see if ame issue and if issue returns will need the main control, called shana and was insteucted to reschedule for 5/24/18 and have customer call office if issue is the same on Tuesday or Wednesday and if ice production is good to cancel service on rues. Or wed., will order ui and main control, no water leaks at time of call.
Near Belton, Texas 76513
Dona
Job Details:
05/18/2018
Authorization from safety met4o00epl1 April. Parts and labor. Found blower belt shredded off blower wheel to motor, causing unit to not blow air through duct. Unit is unplugged at this time not running, Sarah assisted with date and reschedule. 5/24. Would like sooner service if available.
Near Harker Heights, Texas 76548
Mike G.
Job Details:
05/18/2018
KFIS29PBMS02, Arrived on site for unit not making ice when arrived found that the unit is making ice and customer stated that they have replaced water filter and unit started making ice did checked temps in ff and frezer and found ff to be at 39* and freezer is 3* unit making ice and is cooling properly checked unit for water leaks and no leaks found at time of srv....unit checked fine at this time...,
Near Harker Heights, Texas 76548
Mike G.
Job Details:
05/18/2018
KFIS29PBMS02, Arrived on site for unit not making ice when arrived found that the unit is making ice and customer stated that they have replaced water filter and unit started making ice did checked temps in ff and frezer and found ff to be at 39* and freezer is 3* unit making ice and is cooling properly checked unit for water leaks and no leaks found at time of srv....unit checked fine at this time...,
Near Cedar Park, Texas 78613
Lou
Job Details:
05/18/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the control and tested unit. Unit operated as designed. Job completed.
Near Austin, Texas 78737
Connor M.
Job Details:
05/18/2018
WRF560SEYM05 whirlpool refrigerator Arrived on site to test unit for moisture on mullion. Found moisture control not turned on. Temp in apartment very high as it isnt occupied. Turned on moisture control. Unit working properly, no leaks detected.
Near Austin, Texas 78729
Cliff
Job Details:
05/18/2018
Kitchenaid oven KODC304EBL00. Arrived on site to replace blower for oven. Replace upper blower assembly and tested unit. Found all is functioning properly at this time.
Near Coupland, Texas 78615
Nathaniel B.
Job Details:
05/18/2018
Model KRFC704FPS00, Arrived on call for both compartments not cooling properly, found compressor running and getting good heat change but suction line still at room temp and compressor very hot, both compartments at 80 plus degrees, ran test 40 and got no cooling to both compartments at all either unit has a leak in system or compressor has failed, will order all sealed system parts and use evap cover and main control on return due to test 128 control board version is 400 and should be 700 plus and will need to seal around drain tube cup on return with silicone to prevent air leak to keep drain from freezing, pr kristen office will reschedule with customer.
Near Coupland, Texas 78615
Nathaniel B.
Job Details:
05/18/2018
Model KRFC704FPS00, Arrived on call for both compartments not cooling properly, found compressor running and getting good heat change but suction line still at room temp and compressor very hot, both compartments at 80 plus degrees, ran test 40 and got no cooling to both compartments at all either unit has a leak in system or compressor has failed, will order all sealed system parts and use evap cover and main control on return due to test 128 control board version is 400 and should be 700 plus and will need to seal around drain tube cup on return with silicone to prevent air leak to keep drain from freezing, pr kristen office will reschedule with customer.
Near Austin, Texas 78756
Joseph C.
Job Details:
05/18/2018
WTW5000DW1 Arrived on site for “not starting/bouncing around” complaint. Per my previous diagnosis, removed and replaced dampers. Tested and calibrated unit. Unit is performing as designed. No leaks detected, at time of service.
Near Georgetown, Texas 78633
Mike C.
Job Details:
05/18/2018
Whirlpool dishwasher WDT710PAHZ1 Arrived to find door handle loose and door squeaking when opened. Tightened handle and installed new friction pads on hinges. Checked operation and unit checks good with no water leaks.
Near Georgetown, Texas 78628
Jerry C.
Job Details:
05/18/2018
106.51189113 Arrived to inspect ice maker leaking. I found the unit was very out of square and the doors were not sealing as they should. A previous servicer replaced the water valve for the issue and the drain tube adjacent to the valve assembly was dislodged, allowing air to leak into the cabinet. The rc drain was plugged and I corrected the issue, which was causing water to flow into the rc floor area and then leak down through the vacuum breakers and onto the floor. The lower front metal chassis border was bent back and causing air leaks into the cabinet and I corrected it and sealed the cabinet door openings. Operational test good, no leaks observed during service.
Near Manor, Texas 78653
Joseph C.
Job Details:
05/18/2018
WDF520PADM7 Arrived on site for “unit leaking onto floor” complaint. Performed diagnostic test twice and could find no evidence of leakage. Unit is performing as designed. No leaks detected, at time of service.
Near Salado, Texas 76571
Mike G.
Job Details:
05/18/2018
WRB322DMBM00, Arrived on site for unit not making ice and unit getting frost build up Around freezer door checked unit and fou d that the icemaker arm is up icemaker off and fou d no frost build up is freezer turned on icemaker and icemaker started to make ice and called for water and found that the customer is opening the freezer door from the left hand side of the door handle talked to customer about how the freeer door should be opened chexked unit for water leaks and no leaks at time of srv... unit checked fine at this time.....
Near Salado, Texas 76571
Mike G.
Job Details:
05/18/2018
WRB322DMBM00, Arrived on site for unit not making ice and unit getting frost build up Around freezer door checked unit and fou d that the icemaker arm is up icemaker off and fou d no frost build up is freezer turned on icemaker and icemaker started to make ice and called for water and found that the customer is opening the freezer door from the left hand side of the door handle talked to customer about how the freeer door should be opened chexked unit for water leaks and no leaks at time of srv... unit checked fine at this time.....
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/18/2018
Model WDF520PADM7, Arrived on call for dishwasher not draining again, installed check valve drain hose today due to when not in cuse gets water in bottom of the dishwasher above the filter, also got a 6-4 error code which is for float switch and found float switch is bad, skyped offive parts and talked to sara and will reschedule for 5/22/18 but customer request service on 5/25/18
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/18/2018
Model WDF520PADM7, Arrived on call for dishwasher not draining again, installed check valve drain hose today due to when not in cuse gets water in bottom of the dishwasher above the filter, also got a 6-4 error code which is for float switch and found float switch is bad, skyped offive parts and talked to sara and will reschedule for 5/22/18 but customer request service on 5/25/18
Near Leander, Texas 78641
Lou
Job Details:
05/18/2018
arrived on site to inspect microwave vent light not working. Upon further inspection, I found that the light bulb was burnt out and the base was broken causing it to not come out. I quoted the customer $14.62 for the light bulb with tax the total was $15.83. Customer agreed to purchase the light bulb and I removed and replaced the light bulb and housing and tested the unit. The unit operated as designed. Job completed.
Near Austin, Texas 78738
Brandon
Job Details:
05/18/2018
Arrived on site for noise complaint in freezer section, found bad evaporator fan motor. I replaced the fan motor, unit tested good.
Near West Lake Hills, Texas 78746
Kevin
Job Details:
05/18/2018
Arrived on site and inspected unit and found door chute gasket is not on properly and is partially blocking chute when ice is dispensed. Took one picture. After correcting dispensed ice several times and showed the customer how long after the button is released the ice dispenser door stays open. After Correct and gasket know for the repair
Near Buda, Texas 78610
Robert
Job Details:
05/18/2018
Dryer repairs
Near Temple, Texas 76504
Dona
Job Details:
05/18/2018
Arrived on site for high temps in refrigerator, found 4 inch ice build up on evaporator, customer will defrost unit before techs return customer has signed waiver and tech discussed procedure for defrosting. Will need to replace evap cover and rc therm. Found that unit is no longer sending door warning when doors are open. Will need to replace control as well. Sarah assisted with reschedule and parts reschedule 5/23 all water connections dry.
Near Georgetown, Texas 78633
Lou
Job Details:
05/17/2018
arrived on site to inspect refrigerator not cooling in the freezer chamber. Upon further inspection, I found the the unit was in cooling down mode. I took the unit out of cooling down mode and tested unit in diagnostics. Unit tested good. As soon as I took the unit out of diagnostics, the units compressor kicked on. I placed my thermal couple inside the fc at the bottom of the freezer chamber to read the temperature. The unit began at approximately 56 degrees. Within approximately 30 minutes, the unit cooled down to 30 degrees. No water leaks observed during service.
Near Liberty Hill, Texas 78642
Lou
Job Details:
05/17/2018
arrived on site to inspect cooktop parts missing. Upon further inspection, I found that both front and both rear burner heads were missing. Office to order left front, left rear, right front and right rear burner heads and ship directly to the customer. The middle burner head was present. No gas leaks observed during service.
Near Liberty Hill, Texas 78642
Lou
Job Details:
05/17/2018
arrived on site to inspect dishwasher not working. Upon further inspection, I placed the unit in diagnostic mode and found that the sump/motor was not working. The drain pump tested good as did the element. I removed and replaced the sump/motor assembly and tested unit and unit tested good. I found a drill bit and a piece of a dishwasher mount in the sump/drain area. I took pictures for reference. No water leaks observed during service. Job completed.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/17/2018
Model AGR5330BAS3, Arrived on call for range has dent on control panel, found dent on control panel see pic, installed control panel and all checks good, no gas leaks at time of call. Call complete.
Near Round Rock, Texas 78665
Nathaniel B.
Job Details:
05/17/2018
Model AGR5330BAS3, Arrived on call for range has dent on control panel, found dent on control panel see pic, installed control panel and all checks good, no gas leaks at time of call. Call complete.
Near Liberty Hill, Texas 78642
Lou
Job Details:
05/17/2018
Arrived on site to inspect refrigerator kicking on and off and not cooling. Upon further inspection, I found that the customer had the unit unplugged. I plugged the unit in and the unit came on, but shortly kicked off and I could hear the start device pop. I unplugged the unit and removed and replaced the start device and plugged the unit back in. The unit began to operate as designed. After a few minutes the unit began to cool in the freezer chamber. After approximately 15 minutes, the refrigerator chamber began to cool. I put the unit back into its place and set the legs and leveled the chassis. No water leaks observed during service. Job completed.
Near Hutto, Texas 78634
Nathaniel B.
Job Details:
05/17/2018
Model WFG525S0HS0, Arrived on call for all burners continue to click after lit, found that knob switch harness for left rear is bad, ordering switch harness and spark module for top burner igniters, skyped office parts and talked to jordan and will reschedule for 5/22/18.
Near Hutto, Texas 78634
Nathaniel B.
Job Details:
05/17/2018
Model WFG525S0HS0, Arrived on call for all burners continue to click after lit, found that knob switch harness for left rear is bad, ordering switch harness and spark module for top burner igniters, skyped office parts and talked to jordan and will reschedule for 5/22/18.
Near Killeen, Texas 76542
Steve C.
Job Details:
05/17/2018
Arrived on site for the unit light will not turn off. Tested the unit and found the control is defective. Replaced the control and tested the unit. Unit works properly and job complete.
Near Austin, Texas 78703
Connor M.
Job Details:
05/17/2018
KSSC42QMS02 kitchenaid refrigerator Arrived on site to test unit for leaking from ice maker. Fiund crack in mold of icemaker. Replaced and tested unit. Unit working properly, no leaks detected.
Near Georgetown, Texas 78628
Mike C.
Job Details:
05/17/2018
Kitchen Aid dishwasher KDTM404ESS3 Arrived to find lower spray arm not attached to sump. Attached spray arm and checked operation, checked good with no water leaks.
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/17/2018
Model WRF989SDAM01, Arrived on call for grinding noise in freezer, replaced all parts ordered prior due to defrost failure and instructed customer to allow for 24-48 hours for proper cooling and to open and close door from center of handle for proper door closure on freezer, no water leaks at time of call, call complete.
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/17/2018
Model WRF989SDAM01, Arrived on call for grinding noise in freezer, replaced all parts ordered prior due to defrost failure and instructed customer to allow for 24-48 hours for proper cooling and to open and close door from center of handle for proper door closure on freezer, no water leaks at time of call, call complete.
Near Austin, Texas 78745
Robert
Job Details:
05/17/2018
Whirlpool dryer replacement of timer and start switch
Near Austin, Texas 78704
Connor M.
Job Details:
05/17/2018
KUIX505ESS1 kitchenaid ice machine Arrived on site to test unit for over producing ice. Found failed bin thermistor. Replaced and tested unit. Unit working properly, no leaks detected.
Near Austin, Texas 78704
Connor M.
Job Details:
05/17/2018
WRS315SNHM00 whirlpool refrigerator Arrived on site ot test unit for not cooling well. Unit not near an outlet, trapped behind other applainces. Could not plug unit in for diagnosis. Performed over all check and found condenser fan motor not plugged in. Corrected issue and tested unit. Unit working properly. Not connected to water.
Near Round Rock, Texas 78681
Mike C.
Job Details:
05/17/2018
Whirlpool Range WFE525S0HV0 Arrived to find front right burner has a residue left on glass after using the burner. Using Affresh cooktop cleaner I was able to remove the residue. Advised customer to purchase Affresh cooktop cleaner to remove spots from glass. Unit checks good.
Near Troy, Texas 76579
Dona
Job Details:
05/17/2018
Arrived on site for ice maker leaking into bin, dripping water. Replaced ice maker, also found filter needed changed as it was not dispersing water. Found all other parms check good. All water connections dry
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/17/2018
Model ET22DKXAW02, Arrived on call for both compartments not cooling properly, found fresh food control set to coldest setting and evap motor not running, freezer was at 18 degrees and fresh food at 61 degrees, turned evap fan blade by hand and started running, will need evap motor replaced, evap motor 78.80, svc/ labor rf330 179.99 which = 258.79 plus tax 21.35 which = 280.14, customer agreed to est,, installed evap fan and checked operation and evap fan is running know, found no ive in returns or supply and compressor amp draw on red wire is 0.8 amps which is good, collected full balance of 280.14, unit is not connected to water it is in garage. Call complete.
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/17/2018
Model ET22DKXAW02, Arrived on call for both compartments not cooling properly, found fresh food control set to coldest setting and evap motor not running, freezer was at 18 degrees and fresh food at 61 degrees, turned evap fan blade by hand and started running, will need evap motor replaced, evap motor 78.80, svc/ labor rf330 179.99 which = 258.79 plus tax 21.35 which = 280.14, customer agreed to est,, installed evap fan and checked operation and evap fan is running know, found no ive in returns or supply and compressor amp draw on red wire is 0.8 amps which is good, collected full balance of 280.14, unit is not connected to water it is in garage. Call complete.
Near Dripping Springs, Texas 78620
Connor M.
Job Details:
05/17/2018
KRMF706ESS01 kitchenaid refrigerator Arrived on site to test unit for water spraying from dispenser. Found dispenser tube slightly out of place. Corrected issue and tested unit. Unit working properly. No leaks detected.
Near Austin, Texas 78733
Kevin
Job Details:
05/17/2018
Arrived on site And found freezer door is dragging on liner, also found door cam Is off and not allowing door to close properly, took one picture. Will need to bring back door cam and cam thimble and hinge to correct issue. No water leaks from connections at time of service.
Near Austin, Texas 78741
Robert
Job Details:
05/17/2018
Near Georgetown, Texas 78628
Jonathan S
Job Details:
05/17/2018
Whirlpool refrigerator model#WRS975SIDM00. Frosting on fresh food evaporator.
Near Austin, Texas 78746
Kevin
Job Details:
05/17/2018
Arrived on site and inspected cooktop and found F47 code on user interface. Uninstalled cooktop and replaced both modules and UI. After programming cooktop errors have stopped, it will now power on correctly and shows as operating however there is no cookware available yet to be completely certain of operation. Job complete
Near Temple, Texas 76502
Dona
Job Details:
05/17/2018
Arrived on site for rf and LF burners. To heating all the way to temp, found both burners only supplying from one side of coil. Replaced coils and infinite switches. Verified operations on all burners. All check good.
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/17/2018
Model MVWP575GW0, Arrived on call for not getting any hot water when selected only draws cold tap water, checked for error codes and got f5 e1 which is a lid switch fault ehich was the only error, then found when set on warm only gets tap water just as if it was cold but if turned it to hot gets hot water, found that sensor on valve is showing open, replaced valve and temp switch and tested and still same issue, will order control due to still not getting warm water and did not show a temp sensor open for error codes and lid lock will need to. Be ordered, skyped office parts and talked to jordan and will reschedule for 5/24/18
Near Pflugerville, Texas 78660
Nathaniel B.
Job Details:
05/17/2018
Model MVWP575GW0, Arrived on call for not getting any hot water when selected only draws cold tap water, checked for error codes and got f5 e1 which is a lid switch fault ehich was the only error, then found when set on warm only gets tap water just as if it was cold but if turned it to hot gets hot water, found that sensor on valve is showing open, replaced valve and temp switch and tested and still same issue, will order control due to still not getting warm water and did not show a temp sensor open for error codes and lid lock will need to. Be ordered, skyped office parts and talked to jordan and will reschedule for 5/24/18
Near Cedar Park, Texas 78613
Lou
Job Details:
05/17/2018
Arrived on site to install previously diagnosed and ordered parts. Removed and replaced the emitter and receiver board kit and ice maker. Tested unit and unit operated as designed. No water leaks observed during service. Job completed.
Near New Braunfels, Texas 78132
Connor M.
Job Details:
05/17/2018
KICU569XSS00 kitchenaid induction cooktop Installed burners and tested unit. Cookware for induction purchased by customer is not compatible with this cooktop. Confirmed proper function of all burners with cast iron. Job completed.
Near Austin, Texas 78738
Brandon
Job Details:
05/17/2018
Arrived on site for microwave not running a cycle, found bad interlock switch. I removed oven from wall, gained access to interlock switch, replaced interlock, unit tested good. Collected 227.31 on cc