We serviced a
JENN-AIR COOKTOP
Model JGCP536HL00
Near Driftwood, Texas 78619
Andrey
Job Details:
12/10/2025
"Arrived on site to test unit for large flames, tested unit found unit has not been converted to LP, ordering LP kit, recomend replacing regulator as well, customer will be gone for 3 weeks so office will reschedule when they get back; ordrng 1 W11428599 (Lp conversion kit)"
We serviced a
JENN-AIR OVEN
Model JLRP436WP01
Near Dripping Springs, Texas 78620
Andrey
Job Details:
12/10/2025
"Arrived on site to test unit for front left burner have issues, tested unit found it failing the ignite just clicks, inspected and found simmer orfice clogged, cleaned orfice and tested unit is now running as designed no leaks detected job complete no parts installed"
We serviced a
MAYTAG REFRIGERATOR
Model MSS25C4MGZ09
Near Dripping Springs, Texas 78620
Andrey
Job Details:
12/10/2025
"Arrived on site to test unit for frost in freezer, tested unit found gasket is sealing but gap around the liner causing moisture to come on from the bottom, sealed all gaps with adhesive at this time job complete installed W10841140"
We serviced a
WHIRLPOOL DRYER
Model WGD5605MC1
Near Austin, Texas 78721
Joe Z
Job Details:
12/10/2025
Arrived on site for making noise when tumbling. Upon arrival. Ran vent test and has been cleaned by professional company and now passed test per previous visit. I can heard vibration from blower housing. Found blower wheel completely filled with lint. Cleared all lint and test unit. Unit is operating as designed. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Austin, Texas 78721
Joe Z
Job Details:
12/10/2025
"Arrived on site to apartment 503 with dishwasher WDT730HAMZ0 with issue of control not responding. Upon arrival, test unit and found cycle selection key is not responding. Ran diagnostics and get F2-E1 stuck key. Need to replace control. I replaced control W11637583. Test unit and is operating as designed. No leaks present. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Austin, Texas 78721
Joe Z
Job Details:
12/10/2025
"Arrived on site for washer WTW4955HW3 with issue of stuck in wash cycle. Upon arrival , ran diagnostics and get error code F8-E1 long fill/ no fill. Ran manual test an cold valve only hums. I found cold valve at supply is OFF. I turned cold water on at supply and both hot and cold now operate. I also found supply lines are incorrect . I reinstalled supply lines. I ran a normal cycle and unit is operating as designed. No leaks present. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Austin, Texas 78724
Joe Z
Job Details:
12/10/2025
Arrived on site to apartment 13101 for issue of drain pump running continuously. Ran diagnostics and get error code F3-E1 pressure system fault. Need to replace control per service pointer W11766193. I replaced control W11607637. Test unit and is operating as designed. No leaks present. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Austin, Texas 78702
James K
Job Details:
12/10/2025
"Arrived to unit 201 for machine not making ice. Upon arrival, bucket was full of ice. Check temperatures and found reading 0F. FC is stored correctly. Proceeded to run multiple fills tests and found no issues with water flow, ice maker gear or leakage. Filter was already changed out a month ago. Tenant stated unit stopped making ice for a couple of days and started working again. Power cycled unit. Advised customer to monitor. Unit is functioning as designed. No water leaks detected at this time. No parts needed."
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Austin, Texas 78724
Joe Z
Job Details:
12/10/2025
Arrived on site to apartment 3115 for issue of drain pump running continuously. Ran diagnostics and get error code F3-E1 pressure system fault. Need to replace control per service pointer W11766193. I replaced control W11607637. Test unit and is operating as designed. No leaks present. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDF518SAHM
Near Austin, Texas 78758
Miguel
Job Details:
12/10/2025
"Arrived on site for dishwasher showing e4 and not starting. Re oved from counter, inspected and found bo water in tray. Reset and tested. No leaks found. Found heavy build up of suds. Explained suds caused overflow. Advised to use dishwasher cleaner. Working as designes. Call complete. Cc on file."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78757
Miguel
Job Details:
12/10/2025
Arrived on site for washer making noise and drain running. Arrived and unit was plugged in. Drain was not always running. No errors stored. Ran diagnostics and found all components working and sounding normal. All working as designed. Call complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Temple, Texas 76501
Tyler
Job Details:
12/10/2025
"Arrivec on site foot refrigerator needing w11162042 housing, & w11518204 ui. I replaced both parts and tested dispenser. Found no leaks and it working as designed. call complete"
We serviced a
KITCHENAID COOKTOP
Model KCIG556JBL02
Near Austin, Texas 78726
Miguel
Job Details:
12/10/2025
Arrived on site for cooktop showing error code f0ec on back left burner. I reset power and entered configuration mode. Set to 5. Unit reset and is now configured. Test with water. Started boiling. Call complete.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Austin, Texas 78729
Miguel
Job Details:
12/10/2025
Arrived on site with new gearcase. Removed agitator. I was unable to seperate the gearcase from the tub. Gearcase started leaking heacy amount of oil. Cleaned up and advised unit Needs full rebuild. We submit for additional parts. Office will call to reschedule. ; ordrng 1 W11219115 (Outer tub) and 1 W11513244 (Inner basket) and 1 W11568797 (Filter) and 1 WP8533928 (Filter screw)
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near Austin, Texas 78717
Miguel
Job Details:
12/10/2025
"Arrived on site for washer not always filling and not filling deep enough sometimes. Entered diagnostics. Found f0e5. Ran diagnostics test all components passed. Drain line was pushed way past the 6 inches it needs to go in drain. Corrected drain line. During spin unit had a wobble. Found evidence of oil leaking from gearcase. Will need new gearcase, clutch and slider. Agitator does come off. Unit is still under warranty. Reset for Mon am. ; ordrng 1 W11449841 (Gearcase)"
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near West Lake Hills, Texas 78746
James K
Job Details:
12/10/2025
"Arrived on site for lid not latching properly. Upon arrival, proceeded to replace W11670519 latch and corrected supporter hinge on the lid. Tested unit and now unit is functioning as designed, no water leaks detected at this time"
We serviced a
WHIRLPOOL DRYER
Model WED8900BC0
Near Austin, Texas 78746
James K
Job Details:
12/10/2025
"Arrived on site for unit not heating well. Upon arrival, ran unit and found unit heating but not rejecting air. Unable to perform airflow test. Ordering WP8544737 wheel, WP8544742 belt, WP8547157 belt and WPW10448896 motor. No parts replaced. Customer agreed to reschedule Dec 15th ; ordrng 1 WPW10448896 (Motor) and 1 WP8547157 (Belt) and 1 WP8544742 (Belt) and 1 WP8544737 (Wheel)"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Austin, Texas 78733
James K
Job Details:
12/10/2025
"Arrived on site for unit making loud grinding noise when spin cycle ends. Upon arrival, inspected underneath unit and found rotor bolt fell. Resecured bolt. Tested unit and now unit is functioning as designed. No water leak detected at this time. No parts needed"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near New Braunfels, Texas 78130
Tim M
Job Details:
12/10/2025
"Arrived on site to test unit WTW4816FW3 for pump running. Upon arrival customer stated drain pump constantly runs unless power is removed. Applied power, drain pump immediately engaged indicating a pressure system fault. Entered diagnostics and found F3E1 (pressure system fault) error code stored. Cleared error code and reset control, cycled power, drain pump still immediately engages. Inspected pressure hose, found no kinks, punctures or restrictions. Valve is not leaking. Pressure switch on the control has failed. Replaced control (W11603810) and applied power, drain pump no longer immediately engages. Ran a calibration cycle successfully. Unit is now running as designed, no leaks detected, job complete."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS09
Near Austin, Texas 78744
James K
Job Details:
12/10/2025
"Arrived on site for FC door not opening and closing properly. Upon arrival, found ice buildup on the Fc rails, causing difficulty to open and close. Inspect door and gasket and found no issues. Ice maker is not leaking also. Defrosted all ice buildup and applied grease on the rails. Tested unit and now unit is functioning as designed. Advised customer to be mindful of food storage and make sure door is opened at center. Customer agreed. No water leaks detected at this time. No parts needed"
We serviced a
MAYTAG WASHER
Model MVWB765FW4
Near New Braunfels, Texas 78132
Tim M
Job Details:
12/09/2025
"Arrived on site to test unit MVWB765FW4 for not progressing. Customer stated unit senses for a minute then cancels cycle. Entered service mode and found F7E5 (shifter fault) stored. Ran consumer cycle; basket never engaged. Ran manual shifter test no shift to spin. Inspected underside and found gearcase completely drained of oil with rotor bolt seized. Ongoing failure requires full drivetrain rebuild. Recommend replacing gearcase, clutch, slider, rotor, and control. Will be ordering additional parts to ensure completion on return visit. Ordering parts, no parts installed, rescheduled for 12/12 AM.; ordrng 1 W11550891 (Agitator) and 1 W11393685 (Gearcase) and 1 W11260238 (Rotor) and 1 W11195971 (Stator)"
We serviced a
KITCHENAID RANGE
Model KSGG700ESS7
Near New Braunfels, Texas 78132
Tim M
Job Details:
12/09/2025
"Arrived on site to test unit KSGG700ESS7 for buttons not working and drawer not aligned. Customer stated number 3 and oven light buttons unresponsive; lower drawer moves too easily up and down. Verified no input response from those keys. Replaced control panel (W11029431) and transferred all bezels to new panel. Adjusted lower drawer alignment and demonstrated proper lock when fully closed. Customer approved repair. Tested all functions; every button now responds. Unit is now running as designed, no gas leak detected, job complete."
We serviced a
WHIRLPOOL WASHER
Model WFC682CLW0
Near New Braunfels, Texas 78130
Tim M
Job Details:
12/09/2025
"Arrived on site (Unit 10106) to test unit WFC682CLW0 for leak. Upon arrival maintenance stated washer wouldnt drain and was leaking at the door. Removed drain filter; found it packed with hair blocking flow. Cleared debris and ran drain-and-spin; water evacuated properly. Inspected door and found heavy hair buildup along bellow preventing proper seal. Cleaned bellow and verified full contact. Advised maintenance to instruct tenant to wipe door/bellow after use when hair or lint is visible. Unit is now running as designed, no leaks detected, no parts installed, job complete."
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near New Braunfels, Texas 78130
Tim M
Job Details:
12/09/2025
"Arrived on site to test unit WFES3530RS0 for tripping breaker. Upon arrival customer stated breaker trips during every preheat. Breaker has been replaced twice. Engaged a bake cycle; breaker tripped within one minute. Attempted for in burn off but breaker would continuously trip. Found old-style bake element installed. Replaced element (W11182108). Ran 500? burn-off; unit reached temperature and cycled normally with no trips. Advised customer to run additional 90 minutes for full burn-off and relay conditioning. Contacted SAFETY to document under case number 21799629. Unit is now running as designed, job complete."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near New Braunfels, Texas 78130
Tim M
Job Details:
12/09/2025
"Arrived on site to test unit WDP540HAMZ2 for spray arms not moving. Upon arrival customer stated whenever cycle is started it fills with water but the spray arms dont move and detergent does not dissolve.Entered service mode and ran a test cycle, unit filled but wash motor would not engage. Proceeded to replace wash motor assembly (W11613479). Ran another test cycle, wash motor is now properly engaging along with all other components. Unit is now running as designed, no leaks detected, job complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SMHZ05
Near San Marcos, Texas 78666
Tim M
Job Details:
12/09/2025
"Arrived on site to test unit WRF560SMHZ05 for no power. Upon arrival customer stated unit lost power and it has not returned. Verified issue, outlet has power but unit is not powering on. No components getting any voltage. Replaced HV control (W11035836) and tested, power is still not present. Inspected unit harness and found multiple areas of exposed wiring on the power cord (see attached images). New unit wire harness required to resolve issue. Ordering part, office to reschedule.; ordrng 1 W11432778 (Power cord assembly)"
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near San Marcos, Texas 78666
Tim M
Job Details:
12/09/2025
"Arrived on site to test unit MVW4505MW2 for leak. Customer stated leak was resolved (standpipe issue) but now unit leaves clothes soaking wet and wont finish cycles. Entered service mode and ran full test cycle, all components engaged correctly. Started max-fill regular cycle to stress-test standpipe; unit filled to max level, drained completely with no overflow or backup. Found F0E9 (off-balance pause) stored. No functional failure present, unit passes all diagnostics. Advised customer to keep loads 2040% of basket to prevent off balance cycle aborts. At the time of service unit is running as designed, no leaks detected, job complete."
We serviced a
MAYTAG WASHER
Model MVWC415EW1
Near Kyle, Texas 78640
Brandon
Job Details:
12/09/2025
"Arrived on site to look at model MVWC415EW1 for customer complaint of unit making noise during spin. Found issue with hub, actuator, and splutch. I replaced hub, splutch, and actuator. Unit tested good. Parts used w10528947 w10721967 and w11481722"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM01
Near Kyle, Texas 78640
Brandon
Job Details:
12/09/2025
"Arrived on site to look at model WRB322DMBM01 for customer complaint of ice maker not producing ice. Found ice in mold, I jumped ice maker, ice maker harvest failed. I replaced ice maker, tested, unit tested good. Part usedw10884390"
We serviced a
MAYTAG WASHER
Model MVW6200KW1
Near Buda, Texas 78610
Brandon
Job Details:
12/09/2025
"Arrived on site to look at model MVW6200KW1 for customer complaint of unit shaking, found issue with suspension rods. I replaced suspension rods, unit tested good passed all diagnostic tests. No leaks after repair. Part usedw11396716"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Austin, Texas 78745
Leonardo
Job Details:
12/09/2025
"Arrived on site to diagnose a range displaying an F3E0 error code, indicating an open or shorted oven temperature sensor. Verified the error and began testing the temperature sensor. Found the sensor reading outside the proper resistance range at room temperature, confirming the sensor was faulty. Removed the defective sensor and installed a new temperature sensor. Reassembled the unit and powered it back on. Cleared the error code and tested the oven operation. Preheated the oven to 350?F and monitored the temperature climb. Unit reached 350?F properly with no error codes returning. All functions are operating as designed at this time. Job complete"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Austin, Texas 78749
Leonardo
Job Details:
12/09/2025
"Arrived on site to diagnose dishwasher not washing properly. Placed unit into diagnostics and retrieved F6E4 error code, indicating a wash motor failure. Performed further testing and confirmed the sump and motor assembly were not circulating water as designed.Removed the old sump and motor assembly and installed a new replacement. Reassembled the unit and ran a full diagnostic cycle followed by a normal wash test. The wash motor activated properly, spray arms rotated, and the unit circulated water with correct pressure. No leaks were found after replacement. Unit is now operating as designed. Job complete"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM 2
Near Austin, Texas 78736
Leonardo
Job Details:
12/09/2025
"Arrived on site to diagnose dishwasher not washing properly. Tested the unit and confirmed it was filling with water, but the wash motor was not circulating the water through the spray arms. Performed further diagnostics and found the wash motor had failed. Removed the old sump and motor assembly and installed a new sump and motor assembly. Reassembled the unit, ran the dishwasher through a full test cycle, and verified proper water circulation and spray arm operation. Unit is now washing correctly. No leaks present at this time. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Austin, Texas 78723
Joe Z
Job Details:
12/09/2025
"Arrived on site for washer WTW4816FW2 with issue of making a rattling noise. Upon arrival, ran diagnostics and get error code F7-E6 motor fault. Ran manual components test and everything passed except agitation. Found cam has failed and has caused actuator shifter arm to fail. I replaced cam W10721967 and actuator W10913953. Test unit by running a normal cycle and unit is operating as designed. Also found during draining , water started leaking from stand pipe . Job complete"
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Austin, TX 78723
Joe Z
Job Details:
12/09/2025
Arrived on site to apartment 460 to install previously ordered parts. Upon arrival installed Cover W11690848. Unit is operating as designed. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT313CZLZ00
Near Austin, Texas 78721
Joe Z
Job Details:
12/09/2025
Arrived on site for refrigerator WRT313CZLZ00 with issue of door does not close correctly. Upon arrival inspected unit and found doors are closing correctly. The issue is ice forming in freezer and dripping to floor. I found entire base of freezer with sheet of ice. I removed evaporator cover and entire drain is incased in ice. I removed all ice and cleared drain. Unit is operating as designed. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Austin, Texas 78724
Joe Z
Job Details:
12/09/2025
"Arrived on site to apartment 5303 with issue of not operating. Upon arrival, ran diagnostics to test automatic test cycle. Test completed correctly . Ran a normal cycle and unit fills and begins washing correctly. I cannot duplicate an issue with unit at this time. No leaks present. Job complete"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3336SZ01
Near Austin, Texas 78744
Matthew
Job Details:
12/09/2025
Arrived onsite for refrigerator needing fill tube replaced. Replaced w11759139. Tested and unit is now functioning properly. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM08
Near Austin, Texas 78741
Matthew
Job Details:
12/09/2025
"Arrived onsite for refrigerator WRS331SDHM08 needing doors replaced. Replaced LW10912313, LW11026355 and tag W11223753. Took pic of new doors. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW4950HW3
Near Austin, Texas 78741
Matthew
Job Details:
12/09/2025
Arrived onsite for washer WTW4850HW3 filling while not in use. Found solenoid stuck. Replaced valve assembly w11038689. Calibrated and tested. Unit is now functioning properly. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Austin, Texas 78744
Matthew
Job Details:
12/09/2025
"Arrived onsite for refrigerator WRS571CIHZ04 needing ice chute and bucket replaced. Replaced both components W11573761, W11347840 and unit is now functioning properly. Job complete"
We serviced a
WHIRLPOOL DRYER
Model WET4024HW0
Near Austin, Texas 78757
Scott
Job Details:
12/09/2025
"Arrived on site replaced lower harness , control harness, dryer harness . No breaker is tripping as soon as power cord is hooked up. Advised customer to have electrican check outlet and breaker. Called safety. And documented findings . Same reference number. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Leander, Texas 78641
Daniel A
Job Details:
12/09/2025
"Arrived on site to inspect washer model WTW5105HW continuously draining and not unlocking. Upon further inspection, I placed the unit into service mode and observed error code F5E3 F3E2. I checked the condition of the pressure hose and found no obstructions or damage. The control has a failed pressure sensor, which is causing it to drain continuously. I replaced the control and calibrated and tested the machine. The machine is now operating as designed and lid lock is operating as designed. No water leaks observed during service. W11621183"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Hutto, Texas 78634
Andrew P
Job Details:
12/09/2025
"WTW4855HW3. Removed and replaced wash plate bolt w11223765 and agitator w10836692. Ran unit through auto test; washer filled, agitated, drained, and spun out. Washing machine is working as intended. No leaks detected at times of service."
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Hutto, Texas 78634
Andrew P
Job Details:
12/09/2025
"Electric dryer WED560LHW2. Customer reported dryer shuts off on auto dry after 45 minutes with clothes still damp. Advised to try time dry; customer ran it for 1 hour 15 minutes, but clothes remained damp. Heats properly. Tested outlet, thermostat, moisture sensorall good. Dryer runs full time on time dry, but restricted airflow indicates vent issue (clogged or flap not opening). Advised maintenance supervisor to check exterior venting and flap. Issue is with venting, not dryer."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW1
Near Coupland, Texas 78615
Andrew P
Job Details:
12/09/2025
"Dishwasher MODEL WDF341PAPW1. Customer stated the soap was not dissolving and staying at the bottom of the tub. Ran dishwasher through diagnostics with no fault codes. Performed water test with 4 mugs on top rack; dishwasher is getting enough water. Wash pump is pushing enough water through the spray arms. Advised customer to use tablet or pod placed on bottom of tub or in silverware tray, as pods have a coating that can get sticky when wet and prevent dispenser door from opening. Customer noted dispenser door did not open a couple times. Dishwasher is working as intended. No leaks at time of service. Advised customer to place pod on bottom of tub or in silverware tray; if issue persists, call back."
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Elgin, Texas 78621
Andrew P
Job Details:
12/09/2025
"WED8127LC2. Customer stated she kept getting a reminder to clean her vent and lint trap. Ran diagnostics; no fault codes in dryer. Noticed dryer pushed back against wall and collapsing vent. Pulled dryer forward and readjusted. Checked dryer vent to outside; flap would not move, indicating restricted venting in wall. This is causing long dry times and lint trap reminders. Advised customer to have someone professionally clean vent ducting in wall and up to roof. Dryers otherwise working as intended; issue is with wall venting."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Belton, Texas 76513
Tyler
Job Details:
12/09/2025
"Arrived on psych for refrigerator not dispensing or making ice. On arrival customer also stated that the water dispenser would quit working twenty four hours after max ice setting was turned on. On arrival I found the icebox fan motor would not work in test thirty six, the ice maker valve would not open to allow water to the ice maker in test fifty six. I also found an air gap in the lid that covers the ice maker, fan motor and ice maker.Itself. i am ordering the following parts WPW10598013 cover, w11087201 heater, W10846539 ice box fan, w11482383 valve. The office will need to reschedule once.Availability if parts is known; ordrng 1 WPW10598013 (Cover) and 1 W10846539 (Ice box fan)"
We serviced a
KITCHENAID COOKTOP
Model KCGS556ESS06
Near Liberty Hill, Texas 78642
Brandon B
Job Details:
12/09/2025
"Arrived on site for a cooktop KCGS556ESS06 leaking underneath. The customer said that when she is boiling something and it spills over, it will drip into the drawer below. I explained that this is not a water tight system and it's not designed to hold liquids. I called techline to confirm this. Case #21841853"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF540PADM3
Near Leander, Texas 78641
Brandon B
Job Details:
12/09/2025
Arrived on site for a dishwasher WDF540PADM3 not drying the dishes. I verified that the dispenser is opening during diagnostics. Also found the element getting voltage but with an open circuit. I replaced the element w10518394 and also adjusted the springs on the door. Tested in factory mode again and everything is working as designed. No leaks detected while on site
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Kyle, Texas 78640
Luis
Job Details:
12/09/2025
"Arrived on site for ice build up in fresh food evaporator. Per service pointer replaced drip pan and evaporator fan motor that includes thermistor,followed service pointer secured thermistor to evaporator on suction line,secured evaporator to back wall,secured cover with 4 screws,replaced ui reassembled unit ran diagnostic good air flow. Autho from service pointer S16360. Used w11577100,w11457241,w11087438"
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC0
Near Elgin, Texas 78621
Andrew P
Job Details:
12/09/2025
"WTW8500DC0. Customer reported odor from washer. Inspected and noticed soap residue and scum buildup in inner basket after lifting lid; unit had been in storage for 2 years. Confirmed customer had not run a clean cycle. Demonstrated clean wash cycle with bleach, advised using Affresh tablets or vinegar run, and explained how it cleans the stainless steel tub. Washer operating as intended. Advised running clean cycle regularly to flush bacteria and soap buildup. No leaks detected at times of service."
We serviced a
KITCHENAID DISHWASHER
Model KDTM804KPS3
Near Georgetown, Texas 78628
Brandon B
Job Details:
12/09/2025
"Arrived on site to install ordered parts. I installed the upper manifold w11677712, rack w11702824, cover w11101860 and both tube's w10830571. Found a new issue is the retainer clip fell and melted to the heater. I'm ordering a W11702223 retainer clip and W11537778 heater for the return visit. Office will need to reschedule. No leaks detected while on site. ; ordrng 1 W11702223 (Retainer clip) and 1 W11537778 (Heater)"
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Leander, Texas 78641
Brandon B
Job Details:
12/09/2025
Arrived on site to install ordered parts on a washer WETLV27HW3 getting a long fill error. I installed the control ww11629601and calibrated the machine. Also ran a quick cycle to make sure the unit cycles past sensing. Unit is operating as designed. No leaks detected while on site.
We serviced a
JENN-AIR FREEZER
Model JBZFL24IGX10
Near Austin, Texas 78748
Luis
Job Details:
12/09/2025
"Arrived on site for a frozen fill tube.diagnosed defective fill tube heater,replaced fill tube assembly installed updated ui ran icemaker harvest test passed ran fill test passed. W11763849,w11515313"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM04
Near Austin, Texas 78748
Luis
Job Details:
12/09/2025
"Arrived on site for no lights in fresh food compartment. Removed control che ked voltage going into module good voltage reading 120vac diagnosed a defective led module,replaced led bulb lights powered on. W11502762"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM08
Near Austin, Texas 78748
Luis
Job Details:
12/09/2025
"Arrived on site for loud noise. Diagnosed loud vibration noise while fan running,replaced fan scroll,fan motor and blade added gaskets reassembled unit loud noise no longer present. Wp2315539,wp2155789,w11254898,wp2155789,wp2304241,wp2169142"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM08
Near Austin, Texas 78748
Luis
Job Details:
12/09/2025
"Arrived on site. Installed bins to door and butter cover. 3 w11239961,wp2256101"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM04
Near Austin, Texas 78748
Luis
Job Details:
12/09/2025
"Arrived on site for no lights in fresh food compartment. Removed control che ked voltage going into module good voltage reading 120vac diagnosed a defective led module,replaced led bulb lights powered on. W11502762"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDM05
Near Austin, Texas 78745
Luis
Job Details:
12/09/2025
"Arrived to unit 537 for leaking in back during icemaker fill. Removed compressor cover found a defective line ,cut off defective end of line reinstalled line to valve ran water fill no leaks. Unavailable for signature."
We serviced a
WHIRLPOOL FREEZER
Model WRS325SDHZ08
Near Jarrell, Texas 76537
Justin
Job Details:
12/09/2025
Arrived on site for unit not making ice. Inspected unit and found ice maker was turned off. Turned ice maker back on and called for water. Ice maker did a full harvest and called for water. Informed customer allow ice maker 48hrs to produce full harvest. Unit is now functioning properly and as designed to. No leaks present at this time job completed
We serviced a
WHIRLPOOL OVEN
Model WFES3030RS0
Near Jarrell, Texas 76537
Justin
Job Details:
12/09/2025
Arrived on site for unit tripping breaker. Inspected unit tried running broil at 400 unit tripped breaker immediately. Replaced elements both broil and bake whirlpool recommend. Ran broil at 300 unit held and didn't not trip breaker. Ran bake at 500 unit held and didn't trip breaker. Informed customer unit needs do do a factory burn off at 500 degrees. Customer agreed and will turn unit off after 1 hr. Unit is now functioning properly and as designed to. Customer will monitor job completed
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Bertram, Texas 78605
Lou
Job Details:
12/09/2025
"Arrived on site to inspect washer MVW6200KW5 won't start a cycle. Upon further inspection, I placed the unit in diagnostics, showing no error codes and tested. Thenunit filled, then when it was supposed to lock the lid and agitate and spin, the lid lock constantly would make a popping noise and would not lock. I tested the lid lock and found it bad. I removed and replaced the lid lock assembly and calibrated the unit. I retested in diagnostics, and the unit is operating as designed. No water leaks observed during service, job completed. W11670519"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ20
Near Clifton, Texas 76634
Jonathan M
Job Details:
12/09/2025
"Arrived on site for refrigerator model WRS315SDHZ20 with ice getting stuck in the chute. Inspected unit and work area. Customer advised that ice has gotten stuck in the ice chute several times, and when trying to remove it, ice falls onto the floor. Customer noted hardwood floors, which cause a problem. Tested ice dispenser and found ice dispensing properly without clogging the chute. Checked ice door and found no airflow from the chute. Found no frost buildup in the chute; customer confirmed they had not seen any. Called Whirlpool Techline and spoke to Rob, SR# 21846680. He advised that based on current information, the issue is with the customer not allowing ice in the chute to drop fully after dispensing. Advised customer to pull cup away far enough to disengage dispenser motor but not close ice door, allowing ice to drop and preventing clogs. Advised no repairs at this time; unit working and operating as designed. Call complete. No parts installed, and no leaks were present during service."
We serviced a
WHIRLPOOL FREEZER
Model WRS571CIHZ04
Near Austin, Texas 78744
Matthew
Job Details:
12/09/2025
Arrived onsite for refrigerator WRS571CIHZ04 ice not dispensing . Found coupler in chute broken. Ordering chute and coupling. Also ordering container. Office to reschedule ; ordrng 1 W11573761 (Ice chute) and 1 WP2220458 (Coupler) and 1 W10852956 (Coupling spring)
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Meridian, Texas 76665
Jonathan M
Job Details:
12/09/2025
"Arrived on site for washing machine model WTW4957PW0 not completing cycles. Inspected unit and work area. Found machine stuck flashing final spin light with lid locked. Customer confirmed this matched last cycle; previous service (three visits) advised against canceling to preserve errors, but explained control board stores up to four codes unless cleared in diagnostics. Ran diagnostics: no stored error codes. Performed auto test: all functions operated as designed. Checked suspension and basket: both good condition, basket secured to drive shaft. Inspected underside: cam slightly worn from belt, but no oil leaks or gearcase shaft drops. Customer noted prior control board replacements (twice) worked briefly. Consulted GC: possible wrong board installed previously; ordered correct control W11608056 due to all else functioning properly. Office to contact customer for return scheduling given limited parts availability. No parts installed, and no leaks were present during service.; ordrng 1 W11608056 (Control)"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Whitney, Texas 76692
Jonathan M
Job Details:
12/09/2025
"Arrived on site for washing machine model WTW8127LC1 making a grinding noise during operation. Inspected unit and work area. Customer advised unit bought just under a year ago and provided online receipt. Submitted to claims and advised to proceed with repair. Ran unit through diagnostics; no stored error codes. Ran autotest and heard clacking noise and rubbing sound from underneath. Found gearcase W11454734 had leaked oil, with bottom drive shaft on gearcase sliding up and down. Replaced gearcase W11454734 and slider W10734521. Tested unit; operates as designed with no leaks present during operation. Call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Austin, Texas 78758
Miguel
Job Details:
12/09/2025
"Arrived on site with dispenser not working. Customer says after I left it started with same issues. Dispenser works with measured fill but will shortly cycle with the pad. Water pad , dispenser door and user interface were replaced before. Replaced ice pad since it is under the previous leaking Dispenser door. Tested and unit worked just fine. 2nd test and it started acting the same way. Inspected wiring under the door. Could not see any visible breaks. Tested and now dispenser pads do not respond at all. Measure will still works. Unit will need a new door. Office will call to schedule. ; ordrng 1 LW11038917 (Door)"
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPS00
Near Waco, Texas 76712
Tyler
Job Details:
12/09/2025
"Arrived on site for ice machine, not making ice. On arrival, I found the water valve was not opening up or letting any water in and the propeller inside the recirculation pump was broken off. I replaced w11542867 pump, and w10897719 valve. Tested ice machine and found no leaks and unit working as design call complete."
We serviced a
WHIRLPOOL WASHER
Model VWW3809RW0
Near Waco, Texas 76711
Tyler
Job Details:
12/09/2025
"Arrived on site for washer not completing cycles. On arrival i found f8e1 in diagnostic. After further tests I found the valve cold side not opening up, and the pressure hose and harness were broken. I replaced valve and insured unitvhad no leaks but the harness will need to be replaced to prevent unit from overfilling in normal use. Ordering W11665967 harness and rescheduled customer for 12.12.25; ordrng 1 W11665967 (Harness)"
We serviced a
WHIRLPOOL WASHER
Model WET4027HW2
Near Waco, Texas 76707
Tyler
Job Details:
12/09/2025
"Arrived on site for washer, not completing cycles. On arrival confirmed issue and upon further inspection I found the capacitor had failed. I replaced it with w11428524 then tested washer and found it working as designed with no leaks call complete."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RB00
Near Waco, Texas 76710
Tyler
Job Details:
12/09/2025
Arrived on site for refrigerator not making ice. On arrival confirmed issue and found icemaker had stopped mid harvest with 120v going to motor. I replaced ice maker and found u itnwork as designed with no leaks. Call complete
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS10
Near Belton, Texas 76513
Justin
Job Details:
12/09/2025
Arrived on site for unit not powering on. Upon arrival customer stated unit was working again. Customer also stated had stayed off for over a couple of weeks and just powered back on out of no where. Inspected unit found outlet for power cord if you barely jiggle at the outlet unit will turn off and on. Customer has electrical issue at outlet loose neutral. Customer is calling builder to resolve issue job completed
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC2
Near Temple, Texas 76502
Justin
Job Details:
12/09/2025
Arrived on site to repair previously diagnosed issue. Water valve wire harness needs to be replaced. Replaced wire harness as previous tech diagnosed and tested. Water is now dispensing ice side unit both hot and cold. Customer did inform me that not water previously would dispense. Unit is now functioning properly and as designed to. No leaks present at this time job completed
We serviced a
MAYTAG WASHER
Model MVW7230HC2
Near Temple, Texas 76502
Justin
Job Details:
12/09/2025
"Arrived on-site for unit leaking. Upon arrival, inspected unit ran test cycle found leak is happening on the hot side at the valve.and suppli line connection. Tightened connection and tested. Unit is now functioning properly and as designed to. No leaks present at this time job completed"
We serviced a
JENN-AIR FREEZER
Model JBZFL18IGX10
Near Driftwood, Texas 78619
Brandon
Job Details:
12/09/2025
"Arrived on site to look at model JBZFL18IGX10 for customer complaint of ice maker issues. Called techline to see if engineering had a solution yet, there is no solution yet. Case number 21844383"
We serviced a
MAYTAG REFRIGERATOR
Model MSD2550VEW00
Near Taylor, Texas 76574
Andrew P
Job Details:
12/09/2025
"Refrigerator MSD2550VEW00. Customer stated that the refrigerator was not cooling in either section; it was at room temperature. Found the refrigerator unplugged. Plugged in refrigerator; compressor fired up, clicked, and then immediately shut off. Removed and replaced start device wpw1018990. Plugged refrigerator back in; compressor fired right up and was running. Advised customer to give refrigerator 24 hours to reach temperature. Refrigerator is working as intended. No leaks detected at times of service."
We serviced a
JENN-AIR OVEN
Model JJW3830LL01
Near Leander, Texas 78641
Daniel A
Job Details:
12/09/2025
"Arrived on site to inspect oven model JJW3830LL01 displaying error code F2E1 and not starting a cycle. Upon further inspection the customer advised that the problem occurred after a power outage. I was not able to fix the issue by power cycling the unit. The control had failed internally. I replace the console, reassembled and tested. The oven is now operating as designed. W11598124"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ0
Near Cedar Park, Texas 78613
Daniel A
Job Details:
12/09/2025
Arrived on site to inject dishwasher not sitting flush with cabinet. I removed the dishwasher from the cabinet and found there were predrilled holes farther back into the cabinet. I moved the dishwasher back and mounted to the preexisting holes and now the dishwasher is mounted properly. No water leaks observed during service.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC3
Near Austin, Texas 78717
Daniel A
Job Details:
12/09/2025
Arrived on site to install previously diagnosed and ordered parts per previous technician. I installed the left and right hinge receivers. I reassembled and tested the dryer and it is now operating as designed. W11568982 W11568982; O-emld tckt
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Killeen, Texas 76542
Robert
Job Details:
12/09/2025
"MVW7232HW0 Arrived on site for a washer, not advancing cycles, not draining . On arrival, I ran diagnostic and found error code f9e1 a failed control or pump. After trying to test, I found the control and drain pump have failed . I replaced the control board and drain pump, calibrated, and then tested the product, is working as its designed with no water leaks visible from the main water supply."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Killeen, Texas 76542
Robert
Job Details:
12/09/2025
"WTW4816FW2 Arrived on site for a washer, not completing cycles. On arrival, I verified long drain a defective control board. I replaced the control board ,calibrated, and then tested product is working as its designed . No water leaks visible from the main water supply."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Fort Cavazos, Texas 76544
Robert
Job Details:
12/09/2025
"WED4815EW1 Arrived on site for a dryer, taking longer to dry. On arrival, the client stated she was having issues with her washer that it wasn't getting all the water out of the clothes, causing the dryer to work harder . I ran a test on the dryer it worked great . I checked the ventilation that was great as well product works as it's designed no parts used."
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Waco, Texas 76708
Tyler
Job Details:
12/09/2025
Arrived on site for washer leaking. On arrival i confirmed issue and traced leak back to hot side water line not being fully connected. I tightened line and found washer working as deisgned. No leaks call complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ19
Near Waco, Texas 76708
Tyler
Job Details:
12/09/2025
"Arrived on site for refrigerator not making ice. On rival I found ice maker had stopped harvesting and replaced it with w11700250. I found ice maker now working as designed with no leaks call, complete"
We serviced a
WHIRLPOOL WASHER
Model WTW5020SW0
Near Waco, Texas 76705
Tyler
Job Details:
12/09/2025
Arrivec on site for washer not starting cycles. On arrivwl confirmed issue and found latch broken and not responding to voltage being sent to it. I replaced latch w11513252and found washer working as designed with no leaks. Call complete
We serviced a
JENN-AIR MICROWAVE
Model JMDFS24JL01
Near Austin, Texas 78757
Scott
Job Details:
12/09/2025
"Arrived on site for microwave door not opening. Customer also mentioned some times unit will sound like it's running but not heating . Door will sometimes work opening and closing . Ordering microswitchs, also spring and latch kit if needed . Call to set return ; ordrng 1 W11580028 (Monitor switch) and 3 W11397156 (Switch micro)s and 1 W11646238. (Spring and latch kit)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF510PAYS6
Near Austin, Texas 78741
Leonardo
Job Details:
12/09/2025
"Arrived on site to replace the fill valve, sump and motor assembly, upper and lower spray arms, and the upper spray arm manifold. Removed the dishwasher from its cavity and carefully installed all new components. Verified proper alignment and secure connections for each part. Reassembled the unit and ran a full diagnostic cycle. Unit filled, washed, and drained correctly with strong spray pressure from all arms. No abnormal noises were present. Inspected all connections and tubing no leaks detected at this time. Unit is operating as designed. Job complete."
We serviced a
WHIRLPOOL MICROWAVE
Model WMH32519HZ11
Near Austin, Texas 78744
Leonardo
Job Details:
12/09/2025
"Arrived on site to diagnose blower not operating and display not showing time. Verified the issue and found the display was in Energy Save mode, which disables the clock display. Turned Energy Save OFF and restored normal display operation. Pulled the unit down to access the internal blower assembly. Found small debris lodged in the blower wheel, preventing the blades from rotating. Removed the debris and inspected the blower for any further obstruction or damage. Reassembled the unit and tested operation. Blower is now running properly and display is functioning as designed. No one was on-site to sign. Job complete."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78757
Scott
Job Details:
12/09/2025
Arrived on. Site formwasher stuck in drain mode . Ran diagnostics got pressure sensor error. Replaced control. Ran calibration and diagnostics test wash. All. Checked normal. No water leaks detected at time of service. Job complete.
We serviced a
JENN-AIR REFRIGERATOR
Model JF36NXFXDE25
Near New Braunfels, Texas 78130
Andrey
Job Details:
12/09/2025
"Arrived on site to replace previously diagnosed RC harness, replaced and tested unit is now running as designed no leaks detected job complete installed W11661567"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Georgetown, Texas 78628
Wesley
Job Details:
12/09/2025
"Arrived onsite unit 6106 model WTW4855HW3 for control failure continuous drain f3e1 error, repaired by replacing the control W11607637. Tested unit and calibrated. No leaks at time of service. All checks good. No signer available."
We serviced a
WHIRLPOOL WASHER
Model WFW6720RR0
Near Austin, Texas 78701
James K
Job Details:
12/09/2025
Spoke with Salih and confirmed with pictures there is a small scratch on the left side top of cabinet. Weighing call for 3 hours with a 2nd man due to being downtown and property under construction. Please have Parts department check for any imperfections on the new cabinet. Please send PPE as well ; ordrng 1 PPE (PPE)
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Austin, Texas 78758
Miguel
Job Details:
12/09/2025
Arrived on site for dishwasher leaking from front of door. Lowered door and found water came out of corner. Removed door panel. Found foam insulation was sitting inside the tub portion of dishwasher. So it soaked all the water and caused it to leak out. Removed foam and ran cycle. No leaks. Will order and return with foam insulation. Office will call to schedule. ; ordrng 1 W11393126 (Foam sheild) and 1 W11377160 (Brace)
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Austin, Texas 78757
Scott
Job Details:
12/09/2025
Arrived on site for dryer not performing normally. Talked to tenent and they said dryer would run for a bit then cut off and control would go blank . If they wait it will power back on. Found moisture build up arounf UI . Replaced Ui and control. Ran diagnostics and test heat . All checked normal. Advised maintenance to check exterior vents. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS1
Near Austin, Texas 78702
James K
Job Details:
12/09/2025
"Arrived to 553 for unit leaking. Upon arrival, ran test cycle with outer door removed and found leak on the vent assembly. Proceeded to remove vent and found O ring gasket not seated correctly. Moisturized gasket and resecured. Tested unit and now unit is functioning as designed. No water leaks detected at this time. No one available to sign due to vacant unit."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Georgetown, Texas 78626
Wesley
Job Details:
12/09/2025
Arrived onsite for leaking washer WTW4855HW3 Found massive tub crack underneath. Orderign tub to repair. Office to reschedule. No parts; ordrng 1 W10371566 (Tub)
We serviced a
WHIRLPOOL FREEZER
Model WRT318FZDM10
Near Austin, Texas 78749
Luis
Job Details:
12/09/2025
"Arrived on site for water leaking during icemaker fill. Diagnosed extension not fully seated into fill cup,removed icemaker reinstalled extension to fill tube,installed icemaker ran harvest test passed icemaker filled with water no leaks. No one available for signature."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Austin, Texas 78734
Brandon
Job Details:
12/09/2025
Arrived on site to look at model WTW4816FW3 for customer complaint of unit making noise. Found drain hose hitting wall and cabinet during spin. I adjusted drain hose and add zip tie. Unit passed all diagnostic tests.
We serviced a
MAYTAG WASHER
Model MVW6230HW0
Near Buda, Texas 78610
Brandon
Job Details:
12/09/2025
"Arrived on site to look at model MVW6230HW0 for customer complaint of error code and noise. Foudn issue with the actuator which caused the cam and belt to wear down. I replaced actuator, cam, and belt. Ran dlms calibration and diagnostic test. Unit tested good. Parts used w10721967, w11239857, and w10913953"