Near Austin, TX 78725
Carlos G.
Job Details:
01/03/2018
Arrived on site and checked the unit for not washing well. Ran diagnostics and found water temp is not hot enough and customer is using double rinse aid. Advised customer to turn up water heater as control locked out dw heater. Ran calibration cycle to reset heater. No water leaks present after service. Job complete.
Near Killeen, TX 76542
Arthur B.
Job Details:
01/03/2018
WED5100VQ0 (Dryer) - Arrived onsite for customer compliant of dryer not heating. Removed back panel and found element coils broken. Removed bulkhead and used shopvac to remove all lint build up. Removed faulty element and installed new replacement. Reassembled. Tested unit. Unit nowmheat and tumbles as intended. P&L are as follows; 279838 (Element) $69.18,DR310 $159.99 plus taxes. Dryer vent and lint trap was clean of lint at time of service.
Near Lampasas, TX 76550
Arthur B.
Job Details:
01/03/2018
MVWC360AW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer over filling. Ran diagnostics and F2E1 (Stuck Button),F8E3 (Overflow). Inspected pressure hose and blew through hose. Did find small blockage. Was able to free blockage. Calibrate unit. Unit calibrated successfully. Tested unit. Unit now fills,agitates,drain and spins as intended. All water connections were dry at time of service.
Near Leander, TX 78641
Mike C.
Job Details:
01/03/2018
Roper washer RTW4516FW Arrived to check unit for making holes in clothing. Found the water hole on the agitator has sharp edges. Installed new agitator and checked operation, checked good. Checked unit for any leaks and none were found.
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details:
01/03/2018
Arrived on site for water leaking in the dispenser area. Upon arrival this dispenser area was dry. When I dispense water it sprayed all over the place. I found that the waterline was not snapped into the water Spicket in the dispenser area properly. Corrected and tested and all operations are normal and all waterlines are dry.
Near Georgetown, TX 78628
Mike C.
Job Details:
01/03/2018
Whirlpool oven WOS51EC0AS03 Arrived and installed new control and user interface. Ohmed temp sensor and found it to read 1040 which is good. Heated unit to 350 and found cycle temps to average out to 353. Unit checks good.
Near Georgetown, TX 78633
Arthur B.
Job Details:
01/03/2018
KDTE104ESS1 (Dishwasher) - Arrived onsite for customer complaint of dishwasher leaking from bottom. Removed toe plate. Found water dripping from supply hose connected to water valve. Was able to tighten connection. Found water no longer drips. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Chase
Job Details:
01/02/2018
WRF535SMBM arrived on site to check refrigerator for no ice production. Found freezer liner warped not making full contact with light switch. Tested ice maker function by manually pressing switch and it checks good. Will order freezer door to repair unit
Near Killeen, TX 76549
Arthur B.
Job Details:
01/02/2018
MHWE201YW00 (Front Load Washer) - Arrived onsite for customer complaint of front load washer not starting and getting error code F6E1 (Communication Error). Ran diagnostics and found error code F6E1,F7E2. Tested unit. Found unit will not spin or start. Unit will need P&L; WPW10459454 (Control) $225.13, WPW10315848 (Drive Motor),FL450 $199.99 plus taxes. Drive motor is covered under 120 month part warranty. Skyped PARTS and received R/V date of 1/5 per KC. Collected SVC call fee of $108.24 today. Remaining due upon completion. All water connections were dry at time of service.
Near Round Rock, TX 78681
Thomas L.
Job Details:
01/02/2018
Arrived on site for unit not filling with hot water. Found no power from control to hot solenoid. Replaced control. Now hot solenoid is chattering. Replaced valve. All operations are normal and connections are all Arrived site for improper upper rack operation. Found failed adjusters. Replaced and now upper rack works properly. Water connections were dry.
Near Round Rock, TX 78681
Thomas L.
Job Details:
01/02/2018
Arrived on site for unit not filling with hot water. Found no power from control to hot solenoid. Replaced control. Now hot solenoid is chattering. Replaced valve. All operations are normal and connections are all Arrived site for improper upper rack operation. Found failed adjusters. Replaced and now upper rack works properly. Water connections were dry.
Near Harker Heights, TX 76548
Arthur B.
Job Details:
01/02/2018
WTW7040DW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not completing cycles and making loud noises when spinning. Hand spun basket and could hear gearcase grinding. Ran diagnostics and found error code F7E6 (Motor Circuit out of Phase). Ordering gearcase and stator to complete repair. Skyped PARTS and received R/V date of 1/9 per KC. All water connections were dry at time of service.
Near Leander, TX 78641
Jerry C.
Job Details:
01/02/2018
WMH32519FB0 Arrived to inspect flickering internal light. I found the unit had failed since the service call was added. I removed and replaced all switches and mounts for the door and then replaced the fuse. The unit worked as designed and heated well.
Near Round Rock, TX 78665
Thomas L.
Job Details:
01/02/2018
Arrived on site for unit not filling with hot water. Found no power from control to hot solenoid. Replaced control. Now hot solenoid is chattering. Replaced valve. All operations are normal and connections are all dry.
Near Georgetown, TX 78633
Cliff
Job Details:
01/02/2018
Maytag washer MVWC416FW0. Arrived on site to diagnose a washer that is shaking during spin. Found unit not leveled properly causing abnormal shaking during spin. Leveled unit and found all is working properly at this time. No leaks were found at time of service.
Near Austin, TX 78717
Jerry C.
Job Details:
01/01/2018
WMH73521CS5 Arrived to inspect no power and door error. I found the unit would not power up and I removed the switches and mounts and replaced them. I replaced the main fuse and tested the unit. Operational test good.
Near Nolanville, TX 76559
Arthur B.
Job Details:
01/01/2018
WDT720PADM2 (Dishwasher) - Arrived onsite for customer compliant of dishwasher not wash not washing dishes. Tested unit and found sump n motor not pumping water. Removed faulty sump n motor and installed new replacement. Reassembled. Tested unit. Unit now fills,washes,drain and heats as intended. All water connections were dry at time of service.
Near Georgetown, TX 78633
Arthur B.
Job Details:
01/01/2018
WDF730PAYM0 (Dishwasher) - Arrived onsite for customer complaint of dishwasher not cleaning dishes. Tested unit and found sump n motor not moving water. Unit will need new sump n motor. Advised customer that we must obtain authorization for part from extended warranty. Once authorization is given, OF will R/S. All water connections were dry at time of service.
Near Georgetown, TX 78633
Arthur B.
Job Details:
01/01/2018
WFG540H0ES0 (Freestanding Gas Range) - Arrived onsite for customer complaint of freestanding range knobs broken and can’t turn on burners. Found all knobs cracked. Removed knobs and replaced with new replacements. All burners now turn on easily. No other issues found. No gas leaks detected at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details:
12/30/2017
Arrived on site for leaking water during cycle. Tested unit and found that the air vent at the back of the tub was not tightly secured. Corrected and tested and all water connections are dry.
Near Burnet, TX 78611
Thomas L.
Job Details:
12/30/2017
Arrived on site for no operation. Found control would not enter diagnostics and open cold water solenoid. Replaced both and test. Operations are normal and dry.
Near Burnet, TX 78611
Thomas L.
Job Details:
12/30/2017
Arrived on site for no operation. Found control would not enter diagnostics and open cold water solenoid. Replaced both and test. Operations are normal and dry.
Near Georgetown, TX 78633
Thomas L.
Job Details:
12/30/2017
Arrived on site for leaking water. Found pump has crack in housing and is pushing water out under door liner. Both racks are heavily rusted. Door gasket is starting to repair. EST $350 to do motor, $120 per rack. Customer to price me units as this one is 10 years old.
Near Canyon Lake, TX 78133
Daniel A.
Job Details:
12/29/2017
WMH31017FS0 Door open/close error. Replaced upper-lower interlocks -switches. Verifiedcwiring. Normal,operation after service
Near Austin, TX 78754
Carlos G.
Job Details:
12/29/2017
Arrived on site and checked the unit for "door open" issue. Checked components and found a 3 faulty switches and top int. Removed and replaced all 3 switches and top int. Ran test cycle and all checks ok now. Job complete.
Near Killeen, TX 76542
Arthur B.
Job Details:
12/29/2017
MVWX655DW1 (Top Load Washer) - Arrived onsite for customer compliant of top load washer not completing cycles. Tested unit. Found lid latch will not lock. Removed faulty latch and installed new replacement. Reassembled. Calibrated unit. Unit calibrated successfully. No other issues found. All water connections were dry at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details:
12/29/2017
Near Austin, TX 78754
Carlos G.
Job Details:
12/29/2017
Arrived on site and checked the unit for not making ice issue. Checked components and found a piece of ice stuck in icemaker. Removed piece of ice. Ran diagnostics and all checks ok. No water leaks present after service. Job complete.
Near Kyle, TX 78640
Leonardo
Job Details:
12/29/2017
Whirlpool gas range WFG525S0HV0 giving F2E1 error code. Arrived on site to test unit for F2E1 error code shorted keypad. Test unit and found P11 connector had loose connection. Secured connection test unit and unit test good job complete no leaks or error codes present at this time.
Near Georgetown, TX 78633
Thomas L.
Job Details:
12/28/2017
Near Lakeway, TX 78734
Thomas L.
Job Details:
12/28/2017
Arrived on site for lose control panel. Right side screws were loose. Corrected.
Near Austin, TX 78702
Carlos G.
Job Details:
12/28/2017
Arrived on site to replace parts from previous visit. Removed and replaced heater kit and icemaker assembly. Ran test cycle and all checks ok now. No water leaks present after service. Job complete.
Near The Hills, TX 78738
Cliff
Job Details:
12/28/2017
Maytag dryer MED8200FC1. Arrived on site to diagnose a dryer that is making unusual noises when running. Found metal bracket for control board mounting was not secured from factory and was rubbing on drum. Mounted bracket properly and tested unit. Found all is functioning properly at this time.
Near Austin, TX 78754
Carlos G.
Job Details:
12/28/2017
Arrived on site and checked the unit for not cooling issue. Checked components and found a faulty control and evap thermistor. Removed and replaced both. Ran test cycle and all checks ok now. Job complete.
Near Austin, TX 78754
Carlos G.
Job Details:
12/28/2017
Arrived on site and checked the unit for not responding. Checked components and found a faulty control and UI. Removed and replaced control and UI. Ran test cycle and all checks ok. No water leaks present after service. Job complete.
Near Manor, TX 78653
Carlos G.
Job Details:
12/28/2017
Arrived on site and checked the unit for not responding. Checked components and found a faulty control and UI. Removed and replaced control and UI. Ran test cycle and all checks ok. No water leaks present after service. Job complete.
Near Georgetown, TX 78633
Mike C.
Job Details:
12/28/2017
Maytag Refrigerator MFI2269FRZ01 Arrived to check unit for no ice production. Found fill cup and fill tube frozen. Removed ice from fill tube and funnel and cycled ice maker, found motor bad on ice maker. Installed new ice maker and checked operation, checked good. Unit is in a RV and advised customer that when in storage they should turn unit off.
No water leaks were found on unit.
Near Spicewood, TX 78669
Cliff
Job Details:
12/28/2017
Kitchenaid refrigerator KRMF706ESS01. Arrived on site to replace center million for refrigerator. Replaced part and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Round Rock, TX 78681
Wesley
Job Details:
12/28/2017
Fridge filter door latch needed replacement
Near , TX 78617
Carlos G.
Job Details:
12/27/2017
Arrived on site and checked the unit for noise issues. Found a faulty repair kit. Removed and replaced repair kit. Normal wear and tear. Ran test cycle and all checks ok now. Job complete.
Near Round Rock, TX 78665
Thomas L.
Job Details:
12/27/2017
Removed and replaced switches as buttons were sticking. Replaced open socket. All operations are now normal.
Near Georgetown, TX 78633
Thomas L.
Job Details:
12/26/2017
Arrived on site for no drain condition. Found drain pump was not running. Remove and replace drain pump. Unit now works properly with no water leaks.
Near Canyon Lake, TX 78133
Daniel A.
Job Details:
12/26/2017
WRS325FDAB06 Not dispensing water. Defective inlet valve. Replaced inlet valve for defective dispenser solenoid. Verified no leaks. Normal operation after service
Near Georgetown, TX 78628
Thomas L.
Job Details:
12/26/2017
Arrived on site for improper freezer door operation. I found that the upper basket in the freezer was out of time in regard to its gears in the slide sprockets. Corrected timing of upper basket and freezer door now operates properly. Water connections were dry.
Near Hutto, TX 78634
Thomas L.
Job Details:
12/26/2017
Arrived on site no heat conditions. Replaced opening fuses and dryer now operates properly. venting is clear.
Near Round Rock, TX 78664
Thomas L.
Job Details:
12/26/2017
Arrived on site for thumping and noisy operation. Found that the top supports were out of round and noisy. Replaced, tested, now normal, all venting is clear.
Near Austin, TX 78726
Chase
Job Details:
12/22/2017
KFGG500ESS Arrived on sight to check KitchenAid range for inaccurate temperatures. Found oven heating 20 degrees below set temperature. Calibrated oven temperature up 20 degrees and instructed customer on proper way to test temperature and change calibration. All checks good job complete
Near Austin, TX 78726
Chase
Job Details:
12/22/2017
KRFF305ESS0 Arrived on site. Check refrigerator for water filter stuck in housing. Was able to remove water filter, did find a plastic tab on housing broken. The tab does not affect the function of the filter, or increase chances for leak. Replaced filter for customer and customer does not want to replace the housing at this time. Job complete
Near Buda, TX 78610
Carlos G.
Job Details:
12/22/2017
Arrived on site and checked the unit for chirping noise issue. Found noise coming from gearcase, slider, clutch area. Removed and replaced gearcase, clutch, slider. Ran calibration cycle. Ran test cycle and all checks ok at this time. No water leaks present after service. Job complete.
Near Belton, TX 76513
Arthur B.
Job Details:
12/22/2017
WTW5000DW1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not starting. When arrived,found sensing light flashing. Was able to cancel control. Calibrated unit. Unit calibrated successfully. Also found open ground to unit as well. Advised customer that unit must be plugged into 3 prong receptacle. Customer will have plug changes out. No other issues found. All water connections were dry at time of service.
Near Buda, TX 78610
Carlos G.
Job Details:
12/22/2017
Arrived on site and checked the unit for spray arm melted onto element. Confirmed spray arm melted onto element. Element ok and does not need replacement. Removed and replaced melted spray arm. Job complete.
Near Temple, TX 76502
Arthur B.
Job Details:
12/22/2017
WTW8500DC3 (Top Load Washer) - Arrived onsite for customer complaint of water leaking from rear of top load washer and unit off balance. Found unit has dent on LH side of cabinet. Tested unit. Found when agitating, unit will make a clicking noise. Also found unit will not spin all full speed as well. Unit will need new gearcase,clutch,rotor and stator to complete repair. Customer is declining service at this time and speak to POS in possible exchange of the unit. No other issues found at his time. All water connections were dry at time of service.
Near New Braunfels, TX 78130
Connor M.
Job Details:
12/22/2017
WRT311FZDW00 whirlpool refrigerator Installed compressor and access valve. Pulled vacuum for 30 mins. Unit held vac. Charged and tested. Proper frost patern. Cooling properly. No leaks detected.
Near Temple, TX 76501
Arthur B.
Job Details:
12/22/2017
MVWB765FW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer making loud grinding noises when spinning. Spun basket and found gearcase is warn and needs to be replaced. Advised customer that gearcase is an EXPART and would need to come from manufacturer. OF to R/S. All water connections were dry at time of service.
Near Temple, TX 76501
Arthur B.
Job Details:
12/22/2017
WED4815EW1 (Dryer) - Arrived onsite to install new door switch to dryer from prior tech’s diagnosis. Removed defective door switch and installed new replacement. Reassembled. Tested unit. Unit heats and tumbles as intended. Dryer vent and lint trap was clean of lint at time of service.
Near Temple, TX 76501
Arthur B.
Job Details:
12/22/2017
MVWC415EW1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not getting hot water. When arrived, found water temp selector switch was on cool setting. Tested unit on hot water. Found hot water does enter unit as intended. Calibrated unit. Unit calibrated successfully. No other issues found. All water connections were dry at time of service.
Near Temple, TX 76501
Arthur B.
Job Details:
12/22/2017
MEDC215EW1 (Dryer) - Arrived onsite for customer compliant of dryer taking too long to dry. Tested unit. Found dryer vent is route on roof. Found no air coming out of vent. Advised customer to have house venting cleaned. Customer will call housing. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Cedar Creek, TX 78612
Carlos G.
Job Details:
12/22/2017
Arrived on site and checked the unit turning off prematurely. Checked voltage and found voltage drops after about 5 minutes from a constant 240V to 113V to 0V inditcating a house electrical issue as voltage should not drop whatsoever. Customer to fix house electrical. Job complete.
Near San Marcos, TX 78666
Connor M.
Job Details:
12/21/2017
NTW4605EW0 Amanda washer Arrived on site to install valve. Installed and tested unit. Unit working properly. No leaks detected.
Near San Marcos, TX 78666
Connor M.
Job Details:
12/21/2017
WRS325SDHZ whirlpool refrigerator Arrived on site to test unit for led issue. Found failed led in ff section. Installed and leveled unit. Unit working properly, no leaks detected.
Near San Marcos, TX 78666
Connor M.
Job Details:
12/21/2017
WED4815EW1 whirlpool dryer Arrived on site to test unit for burning and making sparks. Found poor connection at terminal block. Corrected issue and tested unit. Unit working properly. Instruct on proper venting and fire hazard.
Near Georgetown, TX 78633
Chase
Job Details:
12/21/2017
wfg540h0es0 arrived on site to check oven for inaccurate temperatures. Inspected bake burner and ignitor and tightened the bake igniter bracket. Preheat oven to 350 degrees and found oven heating at an average of 334 degrees. Calibrated oven temperature up 20 degrees. All checks good job complete
Near Harker Heights, TX 76548
Arthur B.
Job Details:
12/21/2017
WMH73521CS5 (OTR Microwave) - Arrived onsite for customer complaint of OTR microwave getting “OPEN/CLOSE” door error. Found interlock switches burnt. Removed 3 way,NC,NO switches and installed new replacements. Reassembled. Tested unit with 1 cup of water for 2mins. Water was boiling. No other issues found.
Near Harker Heights, TX 76548
Arthur B.
Job Details:
12/21/2017
WDT750SAHZ0 (Dishwasher) - Arrived onsite for customer complaint complaint of dishwasher door handle screw missing. Found threads on handle stripped causing handle screw to become missing. Ordering new handle and screws to complete repair. Advised customer that OF to contact customer for R/V due to part coming from manufacturer. All water connections were dry at time of service.
Near Kyle, TX 78640
Connor M.
Job Details:
12/21/2017
WMH31017FS whirlpool microwave Arrived on site to test unit for not working. Found evidence of arching on all switches.mreplaced and tested unit. Unit working properly.
Near Georgetown, TX 78633
Mike C.
Job Details:
12/21/2017
Maytag Dryer MDE308DAYW Arrived to check unit for no operation. Checked voltage at wall outlet and found 120 volts between L1 and L2, needs 240. Found when moving plug around unit would run. Advised customer that they need a new wall outlet. Collecting service fee of $99.99
Near Killeen, TX 76542
Arthur B.
Job Details:
12/21/2017
WDT750SAHZ0 (Dishwasher) - Arrived onsite for customer complaint complaint of dishwasher door handle screw missing. Found threads on handle stripped causing handle screw to become missing. Ordering new handle and screws to complete repair. Advised customer that OF to contact customer for R/V due to part coming from manufacturer. All water connections were dry at time of service.
Near Manchaca, TX 78652
Connor M.
Job Details:
12/21/2017
WRS325FDAM01 whirlpool refrigerator RF160-169.99 arrived on site to test unit for mot cooling. Found compressor not kicking on when thermostat calls for cooling. Fiund start device not connected properly to compressor. Corrected issue and tested unit. Unit working properly, no leaks detected.
Near Buda, TX 78610
Connor M.
Job Details:
12/21/2017
IMH1205AS0 ikea microwave Arrived on site to test unit for not heating. Found three way micro switch normaly open is closed. Replaced switch and tested unit. Unit working properly.
Near Buda, TX 78610
Connor M.
Job Details:
12/21/2017
WRS325FDAM04 whirlpool refrigerator Installed door and leveled unit. Unit working properly, no leaks detected.
Near New Braunfels, TX 78130
Connor M.
Job Details:
12/20/2017
WED7000DW0 whirlpool dryer Arrived onsite to test unit for not drying well. Found duct leaking on roof allowing water to come into vent and grabbing ling. 100% blockage in duct from house to dryer. Instruct on contacting duct cleaner before continuing use. No buildup inside unit.
Near New Braunfels, TX 78130
Connor M.
Job Details:
12/20/2017
WTW7300DW whirlpool washer Arrived on site to test unit for not spinning well. Found spin cycle turned off. Unit working properly, no leaks detetced.
Near New Braunfels, TX 78130
Connor M.
Job Details:
12/20/2017
WRT311FZDW00 whirlpool refrigerator Arrived on site to test unit for not cooling. Found partial frost patern on evap. Compressor running loud and hot. Will need compressor for repair. Allow 2 hours. Office to schedule directly.
Near Harker Heights, TX 76548
Arthur B.
Job Details:
12/20/2017
WRV986FDEM00 (5 Door French Door Dual Evaporator Refrigerator) - Arrived onsite to install control and icebox to french door refrigerator from prior visit’s diagnosis. Removed icebox assembly. Removed faulty fan. Installed new replacement. Removed back control cover. Removed defective control. Installed new replacement. Reassembled. Tested unit. Icebox fan now circulating air as intended. No other issues found. All water connections were dry at time of service.
Near Liberty Hill, TX 78642
Mike C.
Job Details:
12/20/2017
Maytag wall oven MEW7530DS00 Arrived to find unit with no display or operation. Found thermal fuse bad. Installed new thermal fuse and checked operation, checked good.
Fuse $22.86 - WO380 $159.99
Near Killeen, TX 76549
Arthur B.
Job Details:
12/20/2017
AED4675YQ1 (Dryer) - Arrived onsite for customer compliant of dryer not starting and too hot before it stopped. Removed back panel. Checked continuity on thermal fuse. Found no continuity. Removed thermal fuse and installed new replacement. Tested unit. Found element comes on before hitting start. Was able to reposition element coils so that it did not ground. Retested unit. Unit now tumbles and heats as intended. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Cedar Park, TX 78613
Thomas L.
Job Details:
12/20/2017
Arrived on site for no light operations. removed power from unit for five minutes and re-power unit lights now work and all water connections are good
Near Killeen, TX 76549
Arthur B.
Job Details:
12/20/2017
WFW95HEDW0 (Front Load Washer) - Arrived onsite for customer complaint of front load washer making noises when spinning. Ran diagnostics and found error code F0E1,F5E4. Cleared error codes and ran manual test cycle. Unit completed cycle but did find basket bounces around. Ordering shocks to complete repair. R/S for 12/27. All water connection were dry at time of service.
Near New Braunfels, TX 78132
Connor M.
Job Details:
12/20/2017
KRFC704FBS00 kitchenaid refrigerator Arrived on site to test unit for not making ice. Found ice maker getting power but not advancing. Ordering icemaker for return. Sw approved 27th
Near Killeen, TX 76549
Arthur B.
Job Details:
12/20/2017
MVWX655DW1 (Top Load Washer) - Arrived onsite for customer compliant of top load washer making knocking noise when spinning and draining. Ran diagnostics and found no stored error codes. Ran spin cycle with drain. Found drain hose knocking on wall causing noise. Adjusted hose. Unit drain and spins as intended. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Mike C.
Job Details:
12/20/2017
Jenn Air Wall Oven JJW9630DDB Arrived to install new control on unit. Checked operation and unit checks good.
Control $335.22 - Labor $90.00 - Tax$35.08
Near Jarrell, TX 76537
Arthur B.
Job Details:
12/20/2017
MHW4300DW0 (Front Load Washer) - Arrived onsite for customer complaint of front load washer not starting. Plugged unit. Found drain pump constantly draining. Removed front door. Found coins inside drain trap. Removed coins and reassembled. Found unit will not come on. Unit will need new control to address issue. Customer is declining control at this time. Only charged FL110 labor $129.99 plus taxes. Unit unplugged at this time. All water connections were dry at time of service.
Near Austin, TX 78745
Carlos G.
Job Details:
12/20/2017
Arrived on site and checked the unit for black sut in oven. Confirmed sut coming from oven. Upon removing oven bottom panel, found dog food in front left corner of oven causing black sut. Cleaned out dog food and all checks ok now. Job complete.
Near Granger, TX 76530
Mike C.
Job Details:
12/20/2017
Maytag Dryer MED6600TQ0 Arrived to find unit not starting a cycle and getting a F1 error code. Found control bad on unit. Installed new control and checked operation, checked good. Cleaned any lint from unit.
Control $159.99 - DR300 $59.99 - Price confirmed with MS
Near Jarrell, TX 76537
Arthur B.
Job Details:
12/20/2017
RBS305PRB02 (Wall Oven) - Arrived onsite for customer complaint of wall oven hotter than temperature setting. When arrived,unit was preheated to 350F. Used temperature probe and found temperature was at 425F. Calibrated unit to -25F. Found oven now maintains temperature within +/- 15F. No other issues found. Charged labor WO150 $159.99 plus taxes.
Near San Marcos, TX 78666
Connor M.
Job Details:
12/19/2017
WFG505M0BS whirlpool range Arrived on site to indtall parts for failure. Installed control and valve. Unit working properly at time of service.
Near Georgetown, TX 78633
Thomas L.
Job Details:
12/19/2017
Arrived on site for your washability. Replaced broken detergent dispenser, noisy wash motor, and failing sensor. All water connections were dry after repairs.
Near Martindale, TX 78655
Connor M.
Job Details:
12/19/2017
MVWX655DW0 maytag washer Arrived on site to install parts for repair. Installed hub and washplate. Unit working properly. No leaks detected.
Near Austin, TX 78717
Wesley
Job Details:
12/19/2017
Oven. Needed to be set to Fahrenheit.
Near Kyle, TX 78640
Connor M.
Job Details:
12/19/2017
WMH31017FS0 whirlpool microwave Installed control and tested unit. Unit working properly at time of service.
Near Austin, TX 78748
Connor M.
Job Details:
12/19/2017
NED4655EW1 Amanda dryer Arrived on site to test unit for not drying. Found signs of clogged duct. Ran vent test and unit failed. Confirmed blockage is not inside unit. Instruct on having house ducts cleaned. Unit working properly. Made aware of proper venting and fire hazard.
Near Copperas Cove, TX 76522
Arthur B.
Job Details:
12/19/2017
RED4516FW0 (Dryer) - Arrived onsite for customer complaint of dryer hard to start when pressing the button. Checked incoming voltage and getting 240V properly. Tested switch. Found switch get extremely hot when pressed. Will need new start switch to complete repair. Ordering drive motor additionally Incase motor is faulty. R/V date for 12/21. Dryer vent and lint trap as clean of lint at time of service.
Near Dripping Springs, TX 78620
Connor M.
Job Details:
12/19/2017
MSS26C6MFW01 maytag refrigerator Arrived on site to tets unit for lights not working in cabinet. Unplugged unit and lights came on after plugging back in. This indicates bad control. Found right rear roller broken aswell. Will need roller, axle, ui and control. Model number not pulling up in marcone or servall. Sourced parts from different outlets. Unable to locate main control. Office to schedule directly.
Near Dripping Springs, TX 78620
Connor M.
Job Details:
12/19/2017
WDT730PAHZ0 whirlpool dishwasher Arrived ons ite to insoect unit for rust on lower rack. Found part of the rack hadnt been dipped in paint. Replaced and tested unit. Unit working properly. No leaks detected.
Near Georgetown, TX 78626
Mike C.
Job Details:
12/19/2017
Kitchen Aid wall oven KODE500ESS02 Arrived to find upper door not closing all the way and sticking up on the left side. Removed door and reset back into receiver hinge and found door to close properly. Unit checks good.
Near Canyon Lake, TX 78133
Daniel A.
Job Details:
12/19/2017
WRF532SMBM01 Refrigerator not cooling. defective evaporator fan motor. Shorted control replaced control. Verified fan motor (evaporator/condenser) fan motor operation. Normal operation after service
Near Belton, TX 76513
Arthur B.
Job Details:
12/19/2017
MDB4949SDZ0 (Dishwasher) - Arrived onsite to install new water fill tube in dishwasher from prior tech’s diagnosis. Removed torn water fill tube and installed new replacement. Reassembled tested unit. Unit now fills,washes,drain and heats with no issues. All water connections were dry at time of service.
Near Austin, TX 78734
Thomas L.
Job Details:
12/19/2017
Arrived on site for improper drying times. Check unit and found that the house venting needs to be repaired. The dryer is not the issue.
Near Dripping Springs, TX 78620
Connor M.
Job Details:
12/19/2017
KUDE48FXSS5 kitchenaid dishwasher DW285-159.99 arrived on site to test unit for no power. Found poor connection at power supply box. Repaired connection and tested unit. Unit working properly, no leaks detected.
Near Temple, TX 76502
Arthur B.
Job Details:
12/19/2017
KRFC300ESS01 (French Door Refrigerator) - Arrived onsite for customer complaint of LH RC door handle on french door came loose. Was able to readjust screw and tighten handle screw. Handle now secure. No other issues found. All water connections were dry at time of service.