Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
MFI2569YEM0, Arrived on site to install new water tank with filter head checked unit after repair and unit is now disp water checked unit for water leaks and no leaks found at timemof srv... unit checked fine at this time....
Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
Near New Braunfels, TX 78130
Daniel A.
Job Details: 03/26/2018
MEDB835DC3 Excessive vibration from dryer during use. Installed damper sound pads between rear panel/cabinet. Checked vent/belt/blower. Verified normal sound levels after heater energized. Instruct customer on venting/f
Near New Braunfels, TX 78130
Daniel A.
Job Details: 03/26/2018
MDB4949SDZ0 Excessive vibration/rattling from unit. Verified sump motor wash action normal sound. Drain pump impeller hitting foreign object. Removed drain pump. Checked drain hose. Ran wash cycle. Verified normal wash/action-sound level. Checked water inlet and drain hoses. No leaks detected
Near Hutto, TX 78634
Nathaniel B.
Job Details: 03/26/2018
Model WRF757SDEM01, Arrived on call for fridge light not working intermittenly, found deformed left hand door prior and not fully closing and creating moisture in ice room and compartment, installed left hand fresh food door and checked operations on door and all checked good and is know closing properly, no water leaks after repair, call complete.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 03/26/2018
Model WRF757SDEM01, Arrived on call for fridge light not working intermittenly, found deformed left hand door prior and not fully closing and creating moisture in ice room and compartment, installed left hand fresh food door and checked operations on door and all checked good and is know closing properly, no water leaks after repair, call complete.
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced terminal block. Ran oven and elements. Everything checked OK and oven reach temperature. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced terminal block. Ran oven and elements. Everything checked OK and oven reach temperature. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced terminal block. Ran oven and elements. Everything checked OK and oven reach temperature. Job complete
Near Temple, TX 76504
Dona
Job Details: 03/26/2018
Found valve mechanically open allowing for constant water to flow to icemaker. Major noise on valve. Water is in shut off position at this time so unit will not leak. All water connections are dry. Sarah assisted with reschedule and parts. Customer requested Friday 3/30.
Near Austin, TX 78727
Cliff
Job Details: 03/26/2018
Whirlpool washer WTW8040DW2. Arrived on site to diagnose a washing machine that is not completing spin cycle. Tested unit and found loose wire on clutch Molex connector causing intermittent function of clutch assembly. Rewired Molex connector properly and tested unit. Found all is now functioning properly and no water leaks were found at time of service.
Near Austin, TX 78737
Connor M.
Job Details: 03/26/2018
UMC5200BAS06 whirlpool microwave Arrived on site to test unit for not heating. Found customer had unit uninstalled and on countertop. Plugged unit in to test and found it working properly. Tested unit 3 times with wet paper towel for different lengths of time. Unable to duplicate issue. Unit working properly at time of service.
Near Temple, TX 76502
Dona
Job Details: 03/26/2018
Arrived on site for taking to long to dry, found customer needs to have household ducting cleaned. Dryer vent clear.temps checked good when not connected to house. House has restricted air flow. Found door seal starting to shred. Replaced, seal verified ops all checked good. Instructed customer to let adhesive cure before using dryer.
Near Austin, TX 78737
Connor M.
Job Details: 03/26/2018
WRF993FIFM00 whirlpool refrigerator Arrived on site to test unit for no ice and ff section too warm. Found ff evap frosted over. Will need new evap cover, control, and to return with two hours to perform full defrost along with thermistor svc pointer. Sw aporoved 3/28
Near Belton, TX 76513
Dona
Job Details: 03/26/2018
Arrived on site for no heat after self clean, found open fuse and open thermostat. Replaced both. Unit is now heating. Temperatures check good. All operations checked good.
Near Austin, TX 78727
Scott
Job Details: 03/26/2018
Arrived on site for bottom draw being blue and not SS like rest of unit . Found protective blue film still on draw . Removed film . No gas leaks detected at time of service .
Near Austin, TX 78727
Scott
Job Details: 03/26/2018
We electric range , small burner not heating
Near Buda, TX 78610
Brandon
Job Details: 03/26/2018
Arrived on site for no ice production, I put ice maker in to test found power was getting to icemaker but ice maker module is not working I replaced ice maker unit tested good all water lines were dry at time of service.
Near Austin, TX 78737
Luis
Job Details: 03/26/2018
Refrigerator-added adhesive to liner gaps
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced drain pump. Ran diagnostic test, all functions tested OK. Collect remaining balance of $300.19. No leaks present. Job complete.
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced drain pump. Ran diagnostic test, all functions tested OK. Collect remaining balance of $300.19. No leaks present. Job complete.
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced drain pump. Ran diagnostic test, all functions tested OK. Collect remaining balance of $300.19. No leaks present. Job complete.
Near Harker Heights, TX 76548
Dona
Job Details: 03/26/2018
Arrived on site for no light in oven, found customer put factory bulb back in and unit had light. Pulled bulb and found filament hanging sometimes making contact but not always. Showed customer. Voltage checks good at bulb assy. Customer will need to replace bulb. All other ops check good.
Near Leander, TX 78645
Cliff
Job Details: 03/26/2018
Whirlpool washer WTW8000BW0. Arrived on site to diagnose a washing machine that is making a loud noises during spin. Tested unit and found all parts and components working properly but bearing in unit louder than normal. Bearing has not failed and is not causing any mechanical failures to washer at this time. Noise are not covered under home warranty policy unless caused by a failed part. No repairs to be done at this time as unit is fully functional. No leaks were found at time of service.
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/26/2018
JDB9000CWP2 Detergent dispenser not closing. Removed detergent door. Reinserted seal for dispenser. Verified normal open/closure. Checked water inlet and drain hoses. No leaks detected. Normal operation after service
Near Austin, TX 78735
Connor M.
Job Details: 03/26/2018
WED7590FW0 whirlpool dryer Arrived on site to repair unit for excessive noise. Found rear panel loose from cabinet. Corrected issue by bending panel back into place. Unit working properly. Instruct on proper venting and fire hazard.
Near Austin, TX 78735
Connor M.
Job Details: 03/26/2018
WRT541SZDM00 whirlpool refrigerator Arrived on site to test unit for frosting in freezer. Found forst build up upper left hand corner. Found corner on liner on door sparating from stainless. Will need new door. Corner cap needs replaced. Unit has already been siliconed. Office to schedule directly.
Near Austin, TX 78735
Connor M.
Job Details: 03/26/2018
WMH31017FS0 whirlpool microwave Arrived on site to test unit for door issue. Found fsilure in switch mechanism. Replaced all switches and interlocks. Unit working properly at time of service.
Near Georgetown, TX 78633
Mike C.
Job Details: 03/26/2018
Kitchen Aid Refrigerator KBFO42FTX02 Arrived to install new control kit. Checked operation and unit checks good. No water leaks were found on unit.
Near Salado, TX 76571
Dona
Job Details: 03/26/2018
Arrived on site for loud vibrational noise during rotations, found idler pulley had separated from bearing shaft causing excessive noise. Replaced idler pulley. All rollers checked good. Temperatures checked good. Dryer vent clean.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 03/26/2018
Model MVWB765FW1, Arrived on call for noise complaint from washer when agitation, checked for error codes and got f0 e3 which is overload, f7 e8 which is motor and stator are over temp, Opened the bottom of washer and found shavings in clutch and teeth on gearcase warn down and chipped off on bottom end of shaft, skyped office parts and talked to jordan and will reschedule for 3/29/18, no water leaks at time of call.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 03/26/2018
Model MVWB765FW1, Arrived on call for noise complaint from washer when agitation, checked for error codes and got f0 e3 which is overload, f7 e8 which is motor and stator are over temp, Opened the bottom of washer and found shavings in clutch and teeth on gearcase warn down and chipped off on bottom end of shaft, skyped office parts and talked to jordan and will reschedule for 3/29/18, no water leaks at time of call.
Near Austin, TX 78733
Luis
Job Details: 03/26/2018
Refrigerator-replaced led control
Near Austin, TX 78733
Luis
Job Details: 03/26/2018
Refrigerator-replaced led control
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Check for light issues. Found loose connection at socket for light. Re-position and reconnected connector for socket. All functions tested OK. No leaks present. Job complete
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Check for light issues. Found loose connection at socket for light. Re-position and reconnected connector for socket. All functions tested OK. No leaks present. Job complete
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Check for light issues. Found loose connection at socket for light. Re-position and reconnected connector for socket. All functions tested OK. No leaks present. Job complete
Near Round Rock, TX 78681
Jonathan S
Job Details: 03/26/2018
Whirlpool refrigerator model # WRX988SIBM01 Not making ice.
Near Buda, TX 78610
Brandon
Job Details: 03/26/2018
Arrived on site for washer not draining, put unit into diagnostic mode, found e01 f09 error code, unit not draining. I removed top panel, control panel, door panel, and found clog in drain filter, I removed the clog, unit tested good. Water lines were dry at time of service.
Near Buda, TX 78610
Brandon
Job Details: 03/26/2018
Arrived on site for dryer not heating properly and unit making a clicking noise. I pulled unit out and and removed vent hose, I tested temperature at exhaust, temperature tested good. I showed customer a clog in the vent that we could see on the roof, instructed customer to have the vent cleaned, I left the unit unplugged and instructed customer not to use.
Near Holland, TX 76534
Dona
Job Details: 03/26/2018
Arrived on site for unit leaking from door. Found delivery tube standpipe partially dislodged from sump assembly allowing for water to push straight onto door. Allowed unit to drip out of the door on left side. Reseated standpipe. Verified no leaks. All water connections dry.
Near Holland, TX 76534
Dona
Job Details: 03/26/2018
Arrived on site for unit leaking from door. Found delivery tube standpipe partially dislodged from sump assembly allowing for water to push straight onto door. Allowed unit to drip out of the door on left side. Reseated standpipe. Verified no leaks. All water connections dry.
Near Austin, TX 78732
Paul
Job Details: 03/26/2018
KitchenAid Dishwasher Model KDTE254ESS2; Arrived onsite for the dishwasher that is not starting. Mr stated that is is filling with water but not draining. I checked stored error codes and had an F8E1, F8E4, F5E1, & F6E4. I could hear the drain pump running but making a lot of noise. I found the drain pump with a piece of glass inside it. I removed the glass and tested the machine. The unit is working as designed.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 03/26/2018
Model WRF992FIFM00, Arrived on call for no cool in both compartments, installed compressor, non uv drier and stub and pulled in to a vaccum for 15 min. And held for 15 min, evap coils and valve not needed, unit is pulling down in temp, customer to allow for 24-48 hours for proper cooling, no water leaks at time of call, call complete.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 03/26/2018
Model WRF992FIFM00, Arrived on call for no cool in both compartments, installed compressor, non uv drier and stub and pulled in to a vaccum for 15 min. And held for 15 min, evap coils and valve not needed, unit is pulling down in temp, customer to allow for 24-48 hours for proper cooling, no water leaks at time of call, call complete.
Near Austin, TX 78745
Connor M.
Job Details: 03/26/2018
WMH32L19AS0 whirlpool microwave Arrived on site to test unit for no power. Found fuse checked fine. Diagnosed bad control board. Control getting voltage but not responding. Ordering filter board if needed. Control is expart, office to schedule directly.
Near Georgetown, TX 78633
Mike C.
Job Details: 03/26/2018
Whirlpool vent hood UXT4230ADS2 Arrived to find fan not turning on. Found motor bad on unit. Installed new fan motor and checked operation, checked good.
Near Austin, TX 78703
Luis
Job Details: 03/26/2018
Ice machine-KUIX305ESS1-replaced fan motor and pump assembly
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/26/2018
WDF540PADM2 Not heating. Ran diagnostic. Error code 7-1 for open heater circuit. Verified defective heater. Replaced heater. Verified no leaks. Normal operation after service
Near Austin, TX 78748
Connor M.
Job Details: 03/26/2018
WRS325SDHZ whirlpool refrigerator Arried on site to defrost drain pan and replace drain tube. Defrosted and replaced part. Unit working properly. No leaks detected.
Near Austin, TX 78754
Scott
Job Details: 03/26/2018
Arrived on site for thumping noise and squeaking noise . Found heater box bottom bracket was allowing the heater box to shift left to right causing the metal to rub and squeak. Readjusted bracket . Unit no longer makes noise . Job complete no lint build up at time of service .
Near Austin, TX 78732
Paul
Job Details: 03/26/2018
KitchenAid Dishwasher Model KUDE70FXSS0. Arrived onsite for the dishwasher that is leaking water. I replaced the tub gasket that was found defective on the previous visit. I tested the machine and it is working as designed. There were no water leaks present at the time of service. Call complete.
Near Temple, TX 76502
Dona
Job Details: 03/26/2018
Arrived on site for replacement of broken cooktop. Replaced cooktop. Checked all burners. All ops checked good customer paid with card.
Near Kyle, TX 78640
Brandon
Job Details: 03/26/2018
Arrived on site for dryer not heating properly and unit making a clicking noise. I pulled unit out and and removed vent hose, I tested temperature at exhaust, temperature tested good. I showed customer a clog in the vent that we could see on the roof, instructed customer to have the vent cleaned, I left the unit unplugged and instructed customer not to use.
Near Georgetown, TX 78633
Mike C.
Job Details: 03/26/2018
Whirlpool microwave WMH32519FS0 Arrived to find unit making a sound when fan shuts off. Found damper is making a banging sound when closing, adjusted damper so that it no longer makes noise when closing. Unit checks good.
Near Maxwell, TX 78656
Brandon
Job Details: 03/26/2018
Arrived on site for no ice production, I removed ice maker cover and found power getting to ice maker and ice in the mold, I jumped the ice maker module to test, found bad ice maker. I replaced ice maker, unit filled with water and tested good. Water lines were dry at time of service.
Near Temple, TX 76502
Dona
Job Details: 03/26/2018
Arrived on site for unit leaking out of dispenser, found dispenser paddle on freezer door sticking allowing for contact to water dispenser causing leak. Removed and Reseated paddle and checked to make sure unit was no longer sticking. No leaks. All water connections dry.
Near Austin, TX 78758
Nathaniel B.
Job Details: 03/23/2018
Model MGDC300XW3, Arrived on call for dryer will not start, , replaced shorted timer that previous tech ordered and tested and all checks good, wall vent is clear, no gas leaks at time of call, call complete.
Near Austin, TX 78758
Nathaniel B.
Job Details: 03/23/2018
Model MGDC300XW3, Arrived on call for dryer will not start, , replaced shorted timer that previous tech ordered and tested and all checks good, wall vent is clear, no gas leaks at time of call, call complete.
Near Pflugerville, TX 78660
Jonathan S
Job Details: 03/23/2018
Whirlpool refrigerator model #WRX735SDHZ00. Frost developing in freezer
Near Burnet, TX 78611
Jerry C.
Job Details: 03/23/2018
WED9600TA0 arrived on site for a noisy dryer. Placed the unit in normal dry and once turned on, the unit became very noisy. Upon further inspection, found that the belt tensioner pulley was damaged. Removed and replaced all parts within the dryer repair kit. Cleaned lint within the unit and tested unit. Unit operated as designed. Also found that the bottom drawer of unit was off track. Adjusted the drawer by placing it back on track. Job completed.
Near Austin, TX 78758
Nathaniel B.
Job Details: 03/23/2018
Model WDF520PADM7, Called office and spoke to cali and customer instruct is covered, Arrived on call for dishwasher not heating at all through out the hole cycle. Checked for error codes in diag. And no error codes, ran diag and on hear test checked amps on black wire at front bottom of dishwasher and got 7.8 amps which is good, and heating is working on the element, instructed customer on proper soap and rinse aid use 1 table spoon to teaspoon if still sudsing and rinse aid set to 2 being they are not on water softer and to go away from the packs its to much soap it will effect the drying and washing of dishes, and must run hot water at sink before starting dishwasher, also may have had a bad connection on heating element but pushed connections to heating element on and has heated in test 2 times, no water leaks at time of call, no parts needed, call complete.
Near Austin, TX 78758
Nathaniel B.
Job Details: 03/23/2018
Model WDF520PADM7, Called office and spoke to cali and customer instruct is covered, Arrived on call for dishwasher not heating at all through out the hole cycle. Checked for error codes in diag. And no error codes, ran diag and on hear test checked amps on black wire at front bottom of dishwasher and got 7.8 amps which is good, and heating is working on the element, instructed customer on proper soap and rinse aid use 1 table spoon to teaspoon if still sudsing and rinse aid set to 2 being they are not on water softer and to go away from the packs its to much soap it will effect the drying and washing of dishes, and must run hot water at sink before starting dishwasher, also may have had a bad connection on heating element but pushed connections to heating element on and has heated in test 2 times, no water leaks at time of call, no parts needed, call complete.
Near Lampasas, TX 76550
Dona
Job Details: 03/23/2018
Arrived on site for no water movement from spray arm. Found motor windings opening under load not supplying enough force to punch water. Replaced sump assembly, ran unit 3 startups and drains. checked for leaks all water connections dry.
Near New Braunfels, TX 78130
Daniel A.
Job Details: 03/23/2018
JJW2830DS01 Intermittent chime from interface. Contact tech assist. Per manufacturer replace console/interface. Programmed to correct oven. Normal operation after service
Near Dripping Springs, TX 78620
Connor M.
Job Details: 03/23/2018
JMC7000ADB jennair microwave Arrived on site to test unit for no power. Found bad line fuse. Jumped fuse for further diagnosis. Found failed transformer. Couldnt confirm function of magnetron or cap but they are likely failed aswell. Tranformer not available. Customer declined potential quote. Collected service and minor labor not listed. 119.99 before tax. Job completed.
Near Round Rock, TX 78664
Mike C.
Job Details: 03/23/2018
Whirlpool microwave WMH31017FS0 Arrived to find surface light not turning off or changing brightness. Found relay on control bad. Installed new control and checked operation, checked good.
Near Driftwood, TX 78619
Brandon
Job Details: 03/23/2018
Arrived on site for washer not dissolving pods, put unit into diagnostic test, checked hot and cold water valves, door lock, drain and spin, no error codes were detected. Checked to make sure hot water line was connected to hot side valve, and cold to cold, tested good. Water level tested good. Instructed customer to put pod in before loading clothes, and if problem continues to use the detergent dispenser.
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model WDF520PADW7, Arrived on call for dishwasher not starting cycle, found that customer did not press the start key 2 times to start the cycle, unit filled with water and all functions are working, gave customer instruction on soap and rinse aid use and to run hot water at sink before starting dishwasher, no parts needed, no water leaks at time of call, call complete.
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model WDF520PADW7, Arrived on call for dishwasher not starting cycle, found that customer did not press the start key 2 times to start the cycle, unit filled with water and all functions are working, gave customer instruction on soap and rinse aid use and to run hot water at sink before starting dishwasher, no parts needed, no water leaks at time of call, call complete.
Near Lampasas, TX 76550
Dona
Job Details: 03/23/2018
Arrived on site for no heat. Checked from L1 to neutral found 122 volts, L2 to neutral 122 volts. L1 to L2 0 volts. Customer will need an electrician for household power. Dryer vent is clear.
Near Austin, TX 78738
Connor M.
Job Details: 03/23/2018
WDF520PADM7 whirlpool dishwasher Arrived on site to test unit for failed spray arm. Found spray arm off and melted on element. Replaced arm and confirmed function of heating element. Unit working properly, no leaks detected.
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/23/2018
JIM158XYRS0 Not producing ice. Replaced recirculating pump (prior) and recirculating hose. Checked water inlet and drain hoses. No leaks detected. Normal operation after service
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model KOST100ESS00, Arrived on call for oven door locked in self clean and unit shut down in clean mode and door will not unlock, display is blank, found panel fuse and tod open and also found outlet is bad behinf oven has loose contact in it and also the breaker for oven on outside of hose box is not mounted, svc/ labor wo380 189.99, fuse 33.40, tod 77.84 which = 301.23 plus tax 24.85 which = 326.08, customer agreed to est. installed tod and fuse and elements for nake and broil checked good and display came on when moved wall plug behind oven, not able to test with out good contacts in wall plug, shut power off at outside breaker until electrician can make these repairs to outside braker needs to be mounted and outlet brhind oven will need to be replaced, customer to contact a electrician
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model KOST100ESS00, Arrived on call for oven door locked in self clean and unit shut down in clean mode and door will not unlock, display is blank, found panel fuse and tod open and also found outlet is bad behinf oven has loose contact in it and also the breaker for oven on outside of hose box is not mounted, svc/ labor wo380 189.99, fuse 33.40, tod 77.84 which = 301.23 plus tax 24.85 which = 326.08, customer agreed to est. installed tod and fuse and elements for nake and broil checked good and display came on when moved wall plug behind oven, not able to test with out good contacts in wall plug, shut power off at outside breaker until electrician can make these repairs to outside braker needs to be mounted and outlet brhind oven will need to be replaced, customer to contact a electrician
Near Copperas Cove, TX 76522
Dona
Job Details: 03/23/2018
Arrived on site for no operation. Found 24.6 volts ac at terminal and from white to black on control. Checked tightness of wirenuts, and fuse on board checked good. Customer needs to have an electrician fix household power. All water connections dry.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 03/23/2018
UXL6048YSS jennair vent hood Installed switch board and filters. Unit working properly at time of service.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 03/23/2018
KMHS120ESS4 kitchenaid microwave Arrived on site to test unit for door switch failure. Found switch failed and warped interlocks. Replaced all switches and interlocks. Unit working properly at time of service.
Near San Marcos, TX 78666
Diego G.
Job Details: 03/23/2018
Arrived on site. Check for dispenser issues. Found ice buildup underneath ice bin. Found door shoot not closing all the way allowing hot air to get inside to melt the ice. Also found ice door gasket Lauren. Replaced ice chute and ice door. Cycled dispenser, all functions tested OK. No leaks present. Job complete
Near San Marcos, TX 78666
Diego G.
Job Details: 03/23/2018
Arrived on site. Check for dispenser issues. Found ice buildup underneath ice bin. Found door shoot not closing all the way allowing hot air to get inside to melt the ice. Also found ice door gasket Lauren. Replaced ice chute and ice door. Cycled dispenser, all functions tested OK. No leaks present. Job complete
Near San Marcos, TX 78666
Diego G.
Job Details: 03/23/2018
Arrived on site. Check for dispenser issues. Found ice buildup underneath ice bin. Found door shoot not closing all the way allowing hot air to get inside to melt the ice. Also found ice door gasket Lauren. Replaced ice chute and ice door. Cycled dispenser, all functions tested OK. No leaks present. Job complete
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model MEDX655DW1, Arrived on call for dryer making squeeking noise, found defect in fin of blower wheel causing noise, and found intermitten squeek noise from roller wheels, will order blower wheel and use repair kit on return, skyped office parts and talked to jordan and will reschedule for 3/27/18 but customer requests service on 3/30/18, also found wall vent is restricted, customer to contact mantinance to have wall vent cleared by dryer wall vent cleaning service
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model MEDX655DW1, Arrived on call for dryer making squeeking noise, found defect in fin of blower wheel causing noise, and found intermitten squeek noise from roller wheels, will order blower wheel and use repair kit on return, skyped office parts and talked to jordan and will reschedule for 3/27/18 but customer requests service on 3/30/18, also found wall vent is restricted, customer to contact mantinance to have wall vent cleared by dryer wall vent cleaning service
Near Round Rock, TX 78681
Jonathan S
Job Details: 03/23/2018
Whirlpool dryer model# WED92HEFW0. Not heating.
Near Killeen, TX 76542
Dona
Job Details: 03/23/2018
Arrived on site for no heat on dryer. Found red wire A on timer not connected on 4 pin connection was slid with plastic on right side from factory. Checked temperatures all checked good, dryer vent clear.
Near Austin, TX 78746
Luis
Job Details: 03/23/2018
Ice machine-installed condenser fan motor,water valve and pump
Near Sunset Valley, TX 78745
Brandon
Job Details: 03/23/2018
Arrived on site for washer not working and giving a f1 error code, found bad ccu board, I replaced board and ran trough recalibration and test cycle, unit tested good. Water lines were dry at time of service.
Near Killeen, TX 76542
Dona
Job Details: 03/23/2018
Arrived on site for valve weeping into tub when unit is in off position. Found mechanically open water valve and flow meter. Replaced both unit no longer weeping. Customers hot water on house side does not shut off. Customer is getting a plumber to change hoses and shut offs on house side. All water connections dry. Customer paid cash.
Near Round Rock, TX 78665
Jonathan S
Job Details: 03/23/2018
Whirlpool dryer model # MED6000AW0. Customer complaint of dryer door sagging and scratching panel.
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/23/2018
WTW8500DW0 Unit not coming on. Verified voltage to control. Defective console. F6E2 error code Replaced interface. Checked water inlet and drain hoses. No leaks detected. Ran wash cycle. Normal operation after service
Near Austin, TX 78749
Connor M.
Job Details: 03/23/2018
JDR8895AAS jennair range Arrived on site to replace spark harness. Drilled out all orifice holder screws and replaced harness. Installed all parts damaged in process. Unit now operating properly on all burners.
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model KDTE334GPS60, Arrived on call for dishes not drying, checked for error codes and got 5-1 which is door stuck open which was the only error, ran diag. And found that heater is coming on it is drawing 7.7 amos on black wire under dishwasher which is good, gave customer instruction on soap and rinse aid, home is not on water softner customer had rinse aid set to 3 so set it to 2 and as for soap will need to start with 1 table spoon of liquid and let it fill and slosh for 2 min. And if sudsing reduce to tea spoon of liquid and instructed customer it is mandatory to run hot water at sink before starting dishwasher which incoming water temp is goot on hot 137 degrees, these insteuctions will help with drying, instructed customer aswell beveled top plating will still have standing water and plastics will not dry this is normal, call complete, no parts needed, call complete.
Near Austin, TX 78759
Nathaniel B.
Job Details: 03/23/2018
Model KDTE334GPS60, Arrived on call for dishes not drying, checked for error codes and got 5-1 which is door stuck open which was the only error, ran diag. And found that heater is coming on it is drawing 7.7 amos on black wire under dishwasher which is good, gave customer instruction on soap and rinse aid, home is not on water softner customer had rinse aid set to 3 so set it to 2 and as for soap will need to start with 1 table spoon of liquid and let it fill and slosh for 2 min. And if sudsing reduce to tea spoon of liquid and instructed customer it is mandatory to run hot water at sink before starting dishwasher which incoming water temp is goot on hot 137 degrees, these insteuctions will help with drying, instructed customer aswell beveled top plating will still have standing water and plastics will not dry this is normal, call complete, no parts needed, call complete.
Near Lakeway, TX 78734
Paul
Job Details: 03/23/2018
Whirlpool Oven Model RBS305PDS17. Arrived onsite for the oven that is not getting to temp. I found the bake element burned out. I replaced the bake element and tested the oven. The unit is working as designed. Call complete.
Near Cedar Park, TX 78613
Wesley
Job Details: 03/23/2018
Dishwasher spray arm melted. Replaced arm.
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/23/2018
WRT134TFDB00. Excessive noise during use. Replaced evaporator fan motor. Removed excessive ice from freezer air return/supply. No air leaks detected. Normal operation after service
Near Austin, TX 78726
Cliff
Job Details: 03/23/2018
Whirlpool dishwasher WDF520PADM5. Arrived on site to diagnose a dishwasher that is tripping the breaker. Tested all parts and components of dishwasher and found no mechanical failures at this time and no electrical shorts present in unit at time of service. All parts and components are operating properly, and unit is not drawing excessive power. I did note unit is hooked to AFCI or GFCI breaker which is not recommended, Per the manufacturer, for an appliance to be hooked up to this type of circuit. As there are parts and components on the units that are intentionally not grounded, that can cause the circuits to trip. Homeowner will need electrician to correct electrical issue to complete repairs by installing a standard breaker. No other repairs can be done by appliance express at this time as the fault is not in the unit itself, and no water leaks were found at time of service.
Near Austin, TX 78729
Nathaniel B.
Job Details: 03/23/2018
Model IBMS1455WW0, Arrived on call for microwave start button not responding found that start button has a failure in the control area and will not push in, unit has a 60 months on parts and labor, will order display board and control could not verify which one has the start button from pics, skyped office parts and talked to sarah and will reschedule for 3/27/18
Near Austin, TX 78729
Nathaniel B.
Job Details: 03/23/2018
Model IBMS1455WW0, Arrived on call for microwave start button not responding found that start button has a failure in the control area and will not push in, unit has a 60 months on parts and labor, will order display board and control could not verify which one has the start button from pics, skyped office parts and talked to sarah and will reschedule for 3/27/18