Near Austin, TX 78729
Cliff
Job Details:
03/22/2018
Whirlpool refrigerator WRS571CIDM02. Arrived on site to replace damper assembly for refrigerator her previous technicians diagnosis. Replaced damper assembly and tested unit. Found all is functioning properly at this time and noise issue is resolved. No other failures found at this time and no water leaks found at time of service.
Near Robinson, TX 76706
Mike G.
Job Details:
03/22/2018
WRS325FDAB06, Arrived on site to install new harns-wire and defrost control checked unit after repair and as soon as unit was plugged in unit when into defrsot unit is now defrosting on its own checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time....
Near Robinson, TX 76706
Mike G.
Job Details:
03/22/2018
WRS325FDAB06, Arrived on site to install new harns-wire and defrost control checked unit after repair and as soon as unit was plugged in unit when into defrsot unit is now defrosting on its own checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time....
Near Hutto, TX 78634
Nathaniel B.
Job Details:
03/22/2018
Model WRX986SIHZ00, Arrived on call for fresh food evap senser showing open and control prior did not show this error on first appointment, installed evap motor assem. With sensers for fresh food, and main control, customer to allow for 24-48 hours for proper cooling, unit is pulling down in temp in fresh food section, also did find evap senser was in line were cap line goes in to the evap coil which was the wrong freon line, placed evap senser in correct position in fresh food section,call complete. No water leaks at time of call.
Near Hutto, TX 78634
Nathaniel B.
Job Details:
03/22/2018
Model WRX986SIHZ00, Arrived on call for fresh food evap senser showing open and control prior did not show this error on first appointment, installed evap motor assem. With sensers for fresh food, and main control, customer to allow for 24-48 hours for proper cooling, unit is pulling down in temp in fresh food section, also did find evap senser was in line were cap line goes in to the evap coil which was the wrong freon line, placed evap senser in correct position in fresh food section,call complete. No water leaks at time of call.
Near Belton, TX 76513
Dona
Job Details:
03/22/2018
Arrived on site for broken door handle. Replaced door handle. Customer stated that dryer is taking more than one time to dry clothing. Checked airflow with ducting on and found low flow. Removed ducting checked without and found solid air flow. Ducting is clean to dryer but duct work will need to be cleaned. Instructed customer of air flow. All other parms check correct.
Near Belton, TX 76513
Dona
Job Details:
03/22/2018
Arrived on site for broken door handle. Replaced door handle. Customer stated that dryer is taking more than one time to dry clothing. Checked airflow with ducting on and found low flow. Removed ducting checked without and found solid air flow. Ducting is clean to dryer but duct work will need to be cleaned. Instructed customer of air flow. All other parms check correct.
Near Austin, TX 78758
Scott
Job Details:
03/22/2018
KBFN506ESS01
Near Cedar Park, TX 78613
Nathaniel B.
Job Details:
03/22/2018
Model KRFC704FPS00, Arrived on call for frost and ice forming behind deli drawer, and a no cool condition in fresh food section, , found fresh food evap cover iced over and test 128 shows 400, installed new main control and fresh food evap cover per update for this complaint, customer to allow for 24-48 hours for proper cooling, call complete, no water leaks at time of call, call complete.
Near Cedar Park, TX 78613
Nathaniel B.
Job Details:
03/22/2018
Model KRFC704FPS00, Arrived on call for frost and ice forming behind deli drawer, and a no cool condition in fresh food section, , found fresh food evap cover iced over and test 128 shows 400, installed new main control and fresh food evap cover per update for this complaint, customer to allow for 24-48 hours for proper cooling, call complete, no water leaks at time of call, call complete.
Near New Braunfels, TX 78130
Daniel A.
Job Details:
03/21/2018
MVWB865GW0 washer not agitating/spinning. Ran diagnostic. Error code F7E9. Motor sensor circuit open. Removed /reinserted wiring to stator. Verified normal operation after service. Checked water inlet and drain hoses. No leaks detected
Near New Braunfels, TX 78130
Daniel A.
Job Details:
03/21/2018
WRX988SIBM01 Not cooling. Refrigerant leak detected in refrigerator compartment. Replaced compressor / refrigerator evaporator. Charged unit. Verified no refrigerant leaks. Normal operation after service
Near Cedar Park, TX 78613
Nathaniel B.
Job Details:
03/21/2018
Model KDTE104DSS1, Arrived on call for unit not draining and burning plastic smell, found piece of glass stuck in the impeller of the drain pump and was not able to drain and burning smell was fromseal in drain pump burning, will need drain pump, drain pump 81.02, svc/labor 149.99 dw545 which =231.01 plus tax 19.06 which = 250.07, customer agreed to est., installed drain pump and tested and all checks good, unit is draining and burning smell is gone. Call complete.
Near Cedar Park, TX 78613
Nathaniel B.
Job Details:
03/21/2018
Model KDTE104DSS1, Arrived on call for unit not draining and burning plastic smell, found piece of glass stuck in the impeller of the drain pump and was not able to drain and burning smell was fromseal in drain pump burning, will need drain pump, drain pump 81.02, svc/labor 149.99 dw545 which =231.01 plus tax 19.06 which = 250.07, customer agreed to est., installed drain pump and tested and all checks good, unit is draining and burning smell is gone. Call complete.
Near Austin, TX 78734
Cliff
Job Details:
03/21/2018
Kitchenaid ice machine KUIX305ESS1. Arrived on site to replace water valve for ice machine. Replaced valve and tested unit and found all is functioning properly at this time. No water leaks were found at time of service.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model KSSC42QTS00 Arrived on call for display flashing and nothing is running, control 310.79, svc/labor 209.99 bi150 per jordan at office which =520.78 plus tax 42.96 which = 563.74, customer agreed to est. installed control kit and tested and all is running know customer to allow for 24-48 hours for proper cooling, no water leaks at time of call. Collected full balance of 563.74
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model KSSC42QTS00 Arrived on call for display flashing and nothing is running, control 310.79, svc/labor 209.99 bi150 per jordan at office which =520.78 plus tax 42.96 which = 563.74, customer agreed to est. installed control kit and tested and all is running know customer to allow for 24-48 hours for proper cooling, no water leaks at time of call. Collected full balance of 563.74
Near Temple, TX 76504
Dona
Job Details:
03/21/2018
Arrived on site for unit not always heating. Verified voltage good, verified venting is good. Removed back panel to check heating element and thermostats. Found red wire to heating element was loose not making constant contact with element connector. Reseated and tightened wire connector. verified operations temperatures checked correctly and air flow was good. Dryer ducting clear.
Near Dripping Springs, TX 78620
Luis
Job Details:
03/21/2018
Refrigerator-replaced compressor and evaporator
Near Temple, TX 76502
Dona
Job Details:
03/21/2018
Arrived on site for frost in freezer on left hand side upper. Removed door and was able to mold seal to door with no sag and sealed properly to cavity. Used silicone to seal cavity on seams. Verified no visible air movement from ambient temperatures outside. Tracks looked closed to mfg spec, drawers seated correctly. No improper loading. All water connections dry. Defrosted freezer where frost had accumulated.
Near Buda, TX 78610
Brandon
Job Details:
03/21/2018
Arrived on site for refrigerator not dispensing ice, found coupling on ice bin was damaged causing auger not to dispense ice. Tested ice door, ice door tested good. All water lines were dry at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details:
03/21/2018
Arrived on site for no ice condition. Temperatures were correct and both compartments. Check icemaker and found it it was continually cycling and never Would fill with water. Removed and replaced ice maker. All water connections were dry.
Near Buda, TX 78610
Brandon
Job Details:
03/21/2018
Arrived on site for part hanger, wash plate for washer, I replaced wash plate, unit tested good.
Near Buda, TX 78610
Brandon
Job Details:
03/21/2018
Arrived on site for part hanger, wash plate for washer, I replaced wash plate, unit tested good.
Near Jonestown, TX 78645
Nathaniel B.
Job Details:
03/21/2018
Model KEWD105HSS06, Arrived on call for warming drawer not warming anymore, replaced power switch and tightened wire connections to switch and tested and all checks good, call complete, full est. was collected prior by previous tech.
Near Jonestown, TX 78645
Nathaniel B.
Job Details:
03/21/2018
Model KEWD105HSS06, Arrived on call for warming drawer not warming anymore, replaced power switch and tightened wire connections to switch and tested and all checks good, call complete, full est. was collected prior by previous tech.
Near Jonestown, TX 78645
Nathaniel B.
Job Details:
03/21/2018
Near Jonestown, TX 78645
Nathaniel B.
Job Details:
03/21/2018
Near Round Rock, TX 78681
Steve C.
Job Details:
03/21/2018
Arrived on site for the unit upper rack falls and not draining. Found debris on the drain hose near the garbage disposal and two upper wheel tabs are broken. Replaced the wheels and unclog the drain. Tested the unit and unit works properly. All water connections were dry at the time of service.
Near Blanco, TX 78606
Daniel A.
Job Details:
03/21/2018
WRF993FIFM00 . Not producing ice. Replaced top/bottom icemaker assemblies. Replaced gallon bin on left side refrigerator door. Verified normal cooling/freezing temperatures.
Near Taylor, TX 76574
Jonathan S
Job Details:
03/21/2018
Whirlpool dryer not completing cycles.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model RBS307PVS00, Customer not home till 11 am ,Arrived on call for to high of temp in oven, called whirlpool tech line and talked to robert, at 73 degrees senser should read 1075-1100 ohms, found senser is reading open, file number 7721558204, control 261.41, senser 87.37, w0160 179.99 wo160 which = 528.77 plus tax 43.62 which = 572.39 customer approved est. installed control and senser and tested unit and all checks good, preheated oven to 375 and error did not return, and found when cooling down unit lost power, did check power connections on terminal block on oven and are good, customer to contact a electrician, all checks good, call complete. Got cutt in and cutt out temps 427 on cutt out and 369 on cutt in which = 398 average temp so calabrated temp -20 which is a average temp of 378 when set at 375 degrees.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model RBS307PVS00, Customer not home till 11 am ,Arrived on call for to high of temp in oven, called whirlpool tech line and talked to robert, at 73 degrees senser should read 1075-1100 ohms, found senser is reading open, file number 7721558204, control 261.41, senser 87.37, w0160 179.99 wo160 which = 528.77 plus tax 43.62 which = 572.39 customer approved est. installed control and senser and tested unit and all checks good, preheated oven to 375 and error did not return, and found when cooling down unit lost power, did check power connections on terminal block on oven and are good, customer to contact a electrician, all checks good, call complete. Got cutt in and cutt out temps 427 on cutt out and 369 on cutt in which = 398 average temp so calabrated temp -20 which is a average temp of 378 when set at 375 degrees.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WDT720PADM0, Arrived on call for f2 e2 error code on dishwasher which is no response from ui, ui can not communicate wih main control, tested with new ui and still same issue, will need main control and ui, main control 115.37, ui control panel 209.04, svc/labor 169.99 dw170 which = 449.40 plus tax 40.79 which = 535.19, customer agreed to est. installed main control and ui control panel and tested and all checks good, call complete, no water leaks after repair, call complete.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WDT720PADM0, Arrived on call for f2 e2 error code on dishwasher which is no response from ui, ui can not communicate wih main control, tested with new ui and still same issue, will need main control and ui, main control 115.37, ui control panel 209.04, svc/labor 169.99 dw170 which = 449.40 plus tax 40.79 which = 535.19, customer agreed to est. installed main control and ui control panel and tested and all checks good, call complete, no water leaks after repair, call complete.
Near Temple, TX 76502
Dona
Job Details:
03/21/2018
Arrived on site for not advancing past wash cycle. Found drain hose in stand pipe 2 1/2 foot. Pulled to standard 5". Once hose installed correctly unit filled and advanced. Checked on two cycles. All parms check correctly. All water connections dry. Showed customer on house hot water supply dripping. Ran out of leave behinds did not leave one.
Near Austin, TX 78704
Scott
Job Details:
03/21/2018
Arrived on site for unit not spinning clothes out . Found gear case grinding during the spin cycle . Please get autho for both gearcase and clutch will replace both on return visit . All else checked normal during test . No water leaks detected at time of service . Please call to set return visit
Near Austin, TX 78749
Brandon
Job Details:
03/21/2018
Arrived on site for unit making noise during cycle, I pulled unit out and looked under the washer to inspect cam assy, I found oil all over the floor under the washer and found the gear case to be faulty as well as cam. I replaced the gear case and cam assy, unit tested good, no leaks were detected at time of service.
Near New Braunfels, TX 78132
Daniel A.
Job Details:
03/21/2018
KGCU483VSS Gas smell/leak detected st pressure regulator/gas supply. Replaced pressure regulator. Converted to lp. Verified no gas leaks at regulator/gas connections. Normal operation after service
Near Florence, TX 76527
Mike C.
Job Details:
03/21/2018
Whirlpool dishwasher WDT780SAEM2 Arrived to find upper rack falling down when pulled out. Found left and right front adjuster wheels broken off. Installed new adjusters and checked operation, checked good with no water leaks.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WDT720PADM0, Arrived on call for f2 e2 error code on dishwasher which is no response from ui, ui can not communicate wih main control, tested with new ui and still same issue, will need main control and ui, main control 115.37, ui control panel 209.04, svc/labor 169.99 dw170 which = 449.40 plus tax 40.79 which = 535.19, customer agreed to est. installed main control and ui control panel and tested and all checks good, call complete, no water leaks after repair, call complete.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WDT720PADM0, Arrived on call for f2 e2 error code on dishwasher which is no response from ui, ui can not communicate wih main control, tested with new ui and still same issue, will need main control and ui, main control 115.37, ui control panel 209.04, svc/labor 169.99 dw170 which = 449.40 plus tax 40.79 which = 535.19, customer agreed to est. installed main control and ui control panel and tested and all checks good, call complete, no water leaks after repair, call complete.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WFG361LVS2, Arrived on call for bake will not ignite but broil will, found that flames on broil were good, then tested bake and would not ignite gas, found pans were to high in the lower drawer and were touching the bake igniter taking the spark away, removed pand that were to high in lower drawer of range and tested and know bake is igniting gas and so preheated oven to 350 and know reaches to proper temp and igniter ignited the gas more than 5 times, no parts needed, collected only service fee of 99.99 plus tax which = 108.24 cali from office collected service fee with card on file at the office, no gas leaks at time of call, call complete.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WFG361LVS2, Arrived on call for bake will not ignite but broil will, found that flames on broil were good, then tested bake and would not ignite gas, found pans were to high in the lower drawer and were touching the bake igniter taking the spark away, removed pand that were to high in lower drawer of range and tested and know bake is igniting gas and so preheated oven to 350 and know reaches to proper temp and igniter ignited the gas more than 5 times, no parts needed, collected only service fee of 99.99 plus tax which = 108.24 cali from office collected service fee with card on file at the office, no gas leaks at time of call, call complete.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WFG361LVS2, Arrived on call for bake will not ignite but broil will, found that flames on broil were good, then tested bake and would not ignite gas, found pans were to high in the lower drawer and were touching the bake igniter taking the spark away, removed pand that were to high in lower drawer of range and tested and know bake is igniting gas and so preheated oven to 350 and know reaches to proper temp and igniter ignited the gas more than 5 times, no parts needed, collected only service fee of 99.99 plus tax which = 108.24 cali from office collected service fee with card on file at the office, no gas leaks at time of call, call complete.
Near Leander, TX 78641
Nathaniel B.
Job Details:
03/21/2018
Model WFG361LVS2, Arrived on call for bake will not ignite but broil will, found that flames on broil were good, then tested bake and would not ignite gas, found pans were to high in the lower drawer and were touching the bake igniter taking the spark away, removed pand that were to high in lower drawer of range and tested and know bake is igniting gas and so preheated oven to 350 and know reaches to proper temp and igniter ignited the gas more than 5 times, no parts needed, collected only service fee of 99.99 plus tax which = 108.24 cali from office collected service fee with card on file at the office, no gas leaks at time of call, call complete.
Near Killeen, TX 76542
Mike G.
Job Details:
03/21/2018
ED5VHGXMQ00, Arrived on site to install new knob checked unit after repair and unit is cooling and freezing fine checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Killeen, TX 76542
Mike G.
Job Details:
03/21/2018
ED5VHGXMQ00, Arrived on site to install new knob checked unit after repair and unit is cooling and freezing fine checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Austin, TX 78735
Luis
Job Details:
03/21/2018
Refrigerant-replaced main control,cap and filter housing
Near Round Rock, TX 78665
Steve C.
Job Details:
03/21/2018
Arrived on site for the unit is not heating. Tested the unit and found the cut off fuse with no continuity. Rest of the fuses and connections check good. Replaced the cut off fuse and unit heats and works properly. Advise customer to clean air vents every six months.
Near Round Rock, TX 78665
Steve C.
Job Details:
03/21/2018
Near New Braunfels, TX 78132
Daniel A.
Job Details:
03/21/2018
JIM158XYRS0. Defective recirculating pump not allowing water to flow evenly over evaporator plate to produce ice
Near Temple, TX 76502
Dona
Job Details:
03/21/2018
Arrived on site for abnormally loud when using ice. Found windings on auger motor starting to open creating noise. Ice door not closing at all times causing ice to fall out of door. Replaced motor, solenoid, and ice door. Verified operations no abnormal noise. All water connections dry. All operations checked good.
Near New Braunfels, TX 78130
Kevin
Job Details:
03/21/2018
Arrived on site and replaced all parts diagnosed on previous visit, after replacement allfunction has returned to range. Tested all elements and took one picture of them operating, job complete
Near Austin, TX 78749
Brandon
Job Details:
03/21/2018
Arrived on site for dryer not heating properly, tested ventilation using vent test, found unit was not venting properly. I removed the exhaust hose and checked temperature, temperature tested good and unit cycled properly. Also spoke with Allen, apartment maintenance, and explained to him my findings and showed him the clog in the wall vent.
Near Austin, TX 78749
Brandon
Job Details:
03/21/2018
Arrived on site for dishwasher leaking, I removed outer door panel found leak coming from vent assy. Replaced vent assy and tested unit, unit tested good and all water lines were dry at time of service.
Near Burnet, TX 78611
Thomas L.
Job Details:
03/21/2018
Arrived on site for unit filling and draining repeatedly. Tested unit and found unit needed to be calibrated. Calibrated unit and unit now operates properly. All water connections were dry.
Near Austin, TX 78748
Luis
Job Details:
03/21/2018
Refrigerator-replaced icemaker
Near Killeen, TX 76542
Mike G.
Job Details:
03/21/2018
MVWB750WQ0, Arrived on site to install new drain pump and when doing repair found that the part ordered is not the drain pump part order is Recirc pump and removed drain pump from unit and found a sock stuck in drain pump removed sock reinstalled drain pump and tested unit and unit is now draining checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time.....drain pump is not needed
Near Killeen, TX 76542
Mike G.
Job Details:
03/21/2018
MVWB750WQ0, Arrived on site to install new drain pump and when doing repair found that the part ordered is not the drain pump part order is Recirc pump and removed drain pump from unit and found a sock stuck in drain pump removed sock reinstalled drain pump and tested unit and unit is now draining checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time.....drain pump is not needed
Near Georgetown, TX 78628
Jonathan S
Job Details:
03/21/2018
Whirlpool microwave model# WMH32L19AS1 Arrived on site for microwave intermittently heating and door
Near New Braunfels, TX 78130
Kevin
Job Details:
03/21/2018
RF368LXPB2 Arrived on site and inspected unit and found terminal block has melted and shorted to chassis. Took one picture. Unplugged range and found breaker will not reset, and electrician will need to correct power at source before repair can be performed on range. Will need new terminal block, thermal fuse, and control board to ensure repair on next visit. Do not reschedule until power has been corrected on home.
Near Cedar Park, TX 78613
Nathaniel B.
Job Details:
03/21/2018
Model WFG361LVS2, Arrived on call for bake will not ignite but broil will, found that flames on broil were good, then tested bake and would not ignite gas, found pans were to high in the lower drawer and were touching the bake igniter taking the spark away, removed pand that were to high in lower drawer of range and tested and know bake is igniting gas and so preheated oven to 350 and know reaches to proper temp and igniter ignited the gas more than 5 times, no parts needed, collected only service fee of 99.99 plus tax which = 108.24 cali from office collected service fee with card on file at the office, no gas leaks at time of call, call complete.
Near Cedar Park, TX 78613
Nathaniel B.
Job Details:
03/21/2018
Model WFG361LVS2, Arrived on call for bake will not ignite but broil will, found that flames on broil were good, then tested bake and would not ignite gas, found pans were to high in the lower drawer and were touching the bake igniter taking the spark away, removed pand that were to high in lower drawer of range and tested and know bake is igniting gas and so preheated oven to 350 and know reaches to proper temp and igniter ignited the gas more than 5 times, no parts needed, collected only service fee of 99.99 plus tax which = 108.24 cali from office collected service fee with card on file at the office, no gas leaks at time of call, call complete.
Near Driftwood, TX 78619
Brandon
Job Details:
03/21/2018
Arrived on site for dishwasher leaking, I removed outer door panel found leak coming from vent assy. Replaced vent assy and tested unit, unit tested good and all water lines were dry at time of service.
Near Temple, TX 76502
Dona
Job Details:
03/21/2018
Arrived on site for clothes not always spinning out all the way. Found shift actuator error. Replaced actuator, no codes unit spun and calibrated correctly. All water connections dry.
Near Temple, TX 76502
Dona
Job Details:
03/21/2018
Arrived on site for long dry times, found temperatures on dryer good once ducting removed. Showed customer restrictive airflow on venting with dryer vent connected and vent off. Seal is falling apart on door front will need new seal. Jordan assisted with reschedule and parts.
Near Austin, TX 78728
Nathaniel B.
Job Details:
03/21/2018
Model number MEDB835DW4 , Arrived on call for noise from dryer, found cracked blower wheel prior, installed blower wheel and could not get noise to repeat prior or today, installed blower wheel and instructed customer to run unit as normal and see if noise repeats or not, call complete. Ran dryer and no unnormal noise after repair, call complete.
Near Austin, TX 78728
Nathaniel B.
Job Details:
03/21/2018
Model number MEDB835DW4 , Arrived on call for noise from dryer, found cracked blower wheel prior, installed blower wheel and could not get noise to repeat prior or today, installed blower wheel and instructed customer to run unit as normal and see if noise repeats or not, call complete. Ran dryer and no unnormal noise after repair, call complete.
Near New Braunfels, TX 78130
Kevin
Job Details:
03/21/2018
WED7300XW Arrived on site and inspected unit and found door seal has fallen off. Added new sealed and recommended that customer give it he sieve time to dry before using. No lint build up a new unit cabinet at time of service, job complete
Near Fort Hood, TX 76544
Mike G.
Job Details:
03/21/2018
WED4815EW1, Arrived on site for unit not heating, checked unit and found that the unit is not getting 240v from L1 to N getting 0v from L2 to N getting 120v from L1 to L2 getting 0v customer will need to have a election to fix issue checked and cleaned out all lent found from unit, unit checked fine at this time...
Near Fort Hood, TX 76544
Mike G.
Job Details:
03/21/2018
WED4815EW1, Arrived on site for unit not heating, checked unit and found that the unit is not getting 240v from L1 to N getting 0v from L2 to N getting 120v from L1 to L2 getting 0v customer will need to have a election to fix issue checked and cleaned out all lent found from unit, unit checked fine at this time...
Near New Braunfels, TX 78130
Daniel A.
Job Details:
03/21/2018
WRS325FDAM04 Not dispensing ice. Verified voltage to dispenser motor. Replaced dispenser motor. Dispenser motor operating.Verified normal operation after repair
Near New Braunfels, TX 78130
Daniel A.
Job Details:
03/21/2018
MFX2570AEM3 Not producing ice. Verified defective icemaker not advancing. Replaced icemaker/wire harness. Verified normal advancing of icemaker. Normal operation after service
Near Temple, TX 76502
Dona
Job Details:
03/20/2018
Arrived on site for noise on agitation, found agitator loose, removed covering on agitator. Verified nut not stripped agitator sitting flush no burms, no spacing once unit was tightened. Verified spin and agitate unit checked good. All water connections dry.
Near Canyon Lake, TX 78133
Daniel A.
Job Details:
03/20/2018
KDTE104ESS4 Door not closing properly on tub assembly. Inner panel hitting tub. Replaced tub assembly/left -right door hinges. Replaced outer panel. Checked water inlet and drain hoses. No leaks detected. Verified door opening/closure .
Near Round Rock, TX 78681
Jonathan S
Job Details:
03/20/2018
Whirlpool dishwasher not draining, model# WDT750SAHZ0 Arrived on site for dishwasher not draining. I
Near Austin, TX 78750
Jerry C.
Job Details:
03/20/2018
KSSO42QTX00 Arrived to inspect cooling issues. I found the unit had frozen and plugged the evaporator again. After further inspection, the right door was not properly hung and the pin was not inserted into the upper hinge. I corrected the door/air leak issue and removed the frost from within the unit. The control had been rebuilt prior, but I found the daughter board had a puffed capacitor, C25. I advised the customer of the issue and they elected to have the current, replacement control board installed. I removed and replaced the electronic system and installed the MFG approved replacement assembly. I discussed the ice dispenser issue with the customer and a prior company had removed the dispenser motor and cut the connector off. Repair cannot be made without replacement of the door, or unauthorized wire harness modifications. Operational test good, no leaks observed during service. I am applying our warranty to the door repair and ice removal and BI150, adjusted labor of $80.00. Cont
Near Austin, TX 78726
Jerry C.
Job Details:
03/20/2018
JJW3830DS02 arrived on site to install previously diagnosed and ordered part. Attempted to place unit in diagnostic mode and the control panel would not sense touch. Removed and replaced the control panel and tested unit. Unit tested good. Job completed.
Near Austin, TX 78726
Jerry C.
Job Details:
03/20/2018
RBS305PDS16 arrived on site for oven not working. Upon inspection, customer advised that the inner glass was cracked/broken. Opened unit door and found the inner glass broken/damaged. Office to order inner glass and schedule return 03/23SW.
Near Austin, TX 78717
Wesley
Job Details:
03/20/2018
Arrived on site to repair washer squeaking on spin cycle.
Near Round Rock, TX 78681
Jonathan S
Job Details:
03/20/2018
Whirlpool refrigerator model # WRF535SMBM00. Not making ice
Near Georgetown, TX 78633
Thomas L.
Job Details:
03/20/2018
Arrived on site for no operation. Found no-operation. Turned the switch on the wall and the unit started up. Unit now operates.
Near Georgetown, TX 78633
Thomas L.
Job Details:
03/20/2018
Arrived on site for part hanger for microwave/oven combo, used oven dolly to remove oven, replaced microwave manager control board unit tested good, the user interface assembly was not needed to complete repair. Unit tested good.
Near Round Rock, TX 78681
Jonathan S
Job Details:
03/20/2018
Whirlpool dishwasher model #WDF750SAYM3. Not drying dishes and not feeling heat or steam come from u
Near Liberty Hill, TX 78642
Mike C.
Job Details:
03/20/2018
Whirlpool Refrigerator WRX988SIBM03 Arrived to check unit for not dispensing water or making ice. Found filter head has gotten debris in it and restricting water flow. Installed a new filter head and checked operation, checked good with no water leaks. Customer also purchased a water filter.
Filter $51.49
Near Austin, TX 78727
Cliff
Job Details:
03/20/2018
Whirlpool cooktop W3CG3014XS00. Arrived on site to diagnose a cooktop that flares up when right front burner is used. Found right front burner did not have orifice restrictor installed in burner from factory. Installed proper orifice from personal stock. Tested unit and found all is functioning properly at this time. No gas leaks were found at time of service.
Near Cedar Park, TX 78613
Wesley
Job Details:
03/20/2018
Arrived on site to replace latch for unit not spinning out. Installed latch and calibrated. Tested. All checks good. Unit operating as designed.
Near Killeen, TX 76542
Steve C.
Job Details:
03/20/2018
Arrived on site to replace the left door and rc thermistor due to unit frosting up in the fridge section. Replaced all parts and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Killeen, TX 76542
Steve C.
Job Details:
03/20/2018
Near Killeen, TX 76542
Steve C.
Job Details:
03/20/2018
Near Round Rock, TX 78681
Jonathan S
Job Details:
03/20/2018
Whirlpool refrigerator GI6FARXXF02. Arrived on site for refrigerator making a rattling noise. Perfor
Near Bartlett, TX 76511
Dona
Job Details:
03/20/2018
Arrived on site for high pitched noise in oven when unit is heated at 425 degrees or higher for longer cooking times. Found convection fan motor with windings opening creating noise. Will need to order convection motor, Erika assisted with part and reschedule date.
Near Georgetown, TX 78626
Thomas L.
Job Details:
03/20/2018
arrived on site for no heat condition. Found unit not heating. Found and replaced open fuse. Dryer vent is clean. Visited with customer customer about periodic house vent cleaning.
Near Waco, TX 76706
Mike G.
Job Details:
03/20/2018
WMH31017FS0, Arrived on site for light will not turn on checked unit and found that the top inter lock cam had poped out of place reinstalled cam to interlock and tested unit and light is now turning off when door is shut and light will turn off when door is opened and unit is heating unit checked fine at this time.....
Near Waco, TX 76706
Mike G.
Job Details:
03/20/2018
WMH31017FS0, Arrived on site for light will not turn on checked unit and found that the top inter lock cam had poped out of place reinstalled cam to interlock and tested unit and light is now turning off when door is shut and light will turn off when door is opened and unit is heating unit checked fine at this time.....
Near Austin, TX 78757
Thomas L.
Job Details:
03/20/2018
Arrived on site for heat complaint at vent, tested unit at 400 degrees and instructed customer on how and where the ventilation system works on her oven. Unit tested good.
Near Austin, TX 78746
Luis
Job Details:
03/20/2018
Icemachine-installed updated tube kit
Near Georgetown, TX 78628
Jonathan S
Job Details:
03/20/2018
Whirlpool refrigerator model # GI6FARXXF04. Not making ice and leaking water.
Near Waco, TX 76712
Mike G.
Job Details:
03/20/2018
MFI2670XEB9, Arrived on site for unit leaking from freezer door, checked unit and found that the unit is not draining do to drain hole iced over fou d that the unit is in need of drain tube kit installed drain tube kit and defrosted drain hole and cleaned out sheet of ice from bottom of frezzer and unit and unit is now draining checked unit for water leaks and no leaks found at time of srv....