Near Austin, TX 78731
Cliff
Job Details:
06/27/2018
Kitchenaid dishwasher KUDI02FRSS1. Arrived on site to diagnose a dishwasher with a door that is falling abnormally. Tested unit and found both door Link cables broken. Per notes on work or repair is covered under special project code. Replaced both door link cables and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Salado, TX 76571
Dona
Job Details:
06/27/2018
Arrived on site for timer not advancing, found timer stalled and staying in start of cycle, not moving and keeping unit in start of heat cycle. Replaced timer, verified unit is now counting down and working to spec. Dryer ducting clear, airflow checks good.
Near Leander, TX 78641
Lou
Job Details:
06/27/2018
arrived on site to inspect refrigerator ice maker not working. Upon further inspection, I found that the dispenser is operating as designed, but when attempting to dispense ice, the unit made a loud grinding noise. I found that the actuating arm on the ice maker was broken and caused the ice maker to continuously operate causing the water to overflow into the ice bin and binding up the ice bin motor. I removed the ice bin and attempted to remove the ice maker and found that it was frozen to the cabinet. There is a block of ice at the water tube keeping water from flowing into the ice maker. I am ordering an ice maker, ice bin, and air baffle and scheduled return service for 07/02/18. No water leaks observed during service.
Near Austin, TX 78723
Joseph C.
Job Details:
06/27/2018
WDT710PAHZ1 Arrived on site for “dented front panel” complaint. Inspected unit and found dented panel(center). Removed and replaced panel and handle. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78717
Thomas L.
Job Details:
06/27/2018
Arrived on site for ice clumping and melting together.
Contacted manufactuer and spoke with Bruce about both tabs being broken on the ice box liner housing. See pics.
Bruce is turning over to advisory department. No repair is being done today.
SR# 7722329345
All water connections were dry.
Near Killeen, TX 76542
Arthur B.
Job Details:
06/27/2018
WED4900XW0 (Dryer) - Arrived onsite for customer complaint of dryer still hard starting. Found motor hard to start. Removed motor and installed new replacement. Reassembled and tested. Still getting same issue. Checked voltage to new outlet and found white wire to neutral still drops to 60V when motor starts. Call WPL Techline and spoke with David and confirmed is house wiring issue. Advised customer of finding. Collected for motor and labor. Dryer vent and lint trap was clean of lint at time of service.
Near Granger, TX 76530
Dona
Job Details:
06/27/2018
Arrived on site for no ice production, found from delivery water was not turned on. Turned water on, verified no leaks or drips on line. Unit called for water and started ice production. Freezer door did not come with whirlpool name plate. MS approved D2C to address to send nameplate. Customer will install nameplate. Unit is cooling properly. All operations check good. All water connections dry.
Near New Braunfels, TX 78130
Connor M.
Job Details:
06/27/2018
KDTE334GPS0 kitchenaid dishwasher Arrived on site to test unit for not washing. Fiund cycle starting but no water entering unit. Valve not powering on. Found clip from upper rack under float switch. Removed and tested unit. Unit working properly, no leaks detected.
Near Manor, TX 78653
Nathaniel B.
Job Details:
06/27/2018
Model WMH53520CS6, Arrived on call for the home had a power outage and after power came back on customer set the time on clock and after 5 min time was no longer showing on display but if opened the door on microwave time would then show on display, found that clock energy saver was on so turned it off just on the energy save and waited 8 min. After and time on display did not go out, all checks good, no parts needed call complete. katkarkel@sbcglobal.net
Near Manor, TX 78653
Nathaniel B.
Job Details:
06/27/2018
Model WMH53520CS6, Arrived on call for the home had a power outage and after power came back on customer set the time on clock and after 5 min time was no longer showing on display but if opened the door on microwave time would then show on display, found that clock energy saver was on so turned it off just on the energy save and waited 8 min. After and time on display did not go out, all checks good, no parts needed call complete. katkarkel@sbcglobal.net
Near Marble Falls, TX 78654
Jerry C.
Job Details:
06/27/2018
MVWX655DW1 Arrived to inspect no spin or agitate. I found the gear case lower seal had ruptured and required replacement. I removed and replaced the gear case and cam kit and removed oil from the motor and belt. I calibrated the unit and tested. Operational test good, no leaks observed during service.
Near Leander, TX 78641
Lou
Job Details:
06/27/2018
arrived on site to inspect damage to a range. Upon arrival, the customer advised that he bought the unit and when it was delivered he had to leave on a business trip. When he returned and began the remodel on his home, he went to install the unit and found that the left side panel had a large dent in it and a the cooktop was badly damaged on the right side. The customer notified Home Depot and he is keeping the unit and would like to replace the damaged items. I am ordering a cooktop (black) and left side panel (black) and will return on 07/03/18 for return service. No gas leaks detected as the unit is not completely connected at this time.
Near Austin, TX 78731
Cliff
Job Details:
06/27/2018
Kitchenaid refrigerator KBSD618ESS01. Arrived on site to replace icemaker and water valve for refrigerator. Replaced both parts and tested unit. Found all is functioning properly at this time and water valves no longer seeping. Control is not needed to repair this unit. No leaks found after services were performed.
Near Harker Heights, TX 76548
Arthur B.
Job Details:
06/27/2018
KERS205TSS0 (Freestanding Range) - Arrived onsite for customer complaint of no start activity on freestanding range. When arrived, found control has “Power Loss” error. Was able to cancel and check all elements and oven. All work as intended. Checked voltage to unit. Unit getting 240V. No other issues found.
Near Florence, TX 76527
Dona
Job Details:
06/27/2018
Arrived on site for replacement of washplate due to washplate being worn down on shaft not allowing unit to cycle or move clothes to clean. Replaced washplate and verified unit is now washing clothing correctly. All water connections dry. Unit is working to spec
Near New Braunfels, TX 78132
Connor M.
Job Details:
06/27/2018
WDT970SAHZ0 whirlpool dishwasher Arrived on site to test unit for not drying well. Entered diagnostic cycle and forced heating element. Element powered on. Instruct on proper function. No leaks detected.
Near Harker Heights, TX 76548
Arthur B.
Job Details:
06/27/2018
MSB27C2XAM00 (SxS Refrigerator) - Arrived onsite for customer complaint of no ice producing on SxS refrigerator. Removed icemaker cover and found ice maker motor stopped mid harvest. Found faulty icemaker. Removed icemaker and installed new replacement. Reassembled. Unit called for water as intended. No other issues found. All water connections were dry at time of service.
Near Leander, TX 78641
Lou
Job Details:
06/27/2018
arrived on site to install previously diagnosed and ordered part. Removed and replaced the right front gas valve and tested. The unit operates as designed. I checked all gas connections and found/detected no leaks. Job completed.
Near Leander, TX 78641
Thomas L.
Job Details:
06/27/2018
Arrived on site for no cool condition in fresh food section. Found freezer evaporator severely iced over. Unit is so iced over that it will need to e manually defrosted. Will return with all defrost system and use only what is needed on return. Unit went into defrost during diagnostics but the heater did not come on.
Near Austin, TX 78745
Luis
Job Details:
06/27/2018
Refrigerator-replaced main control and ui
Near Kyle, TX 78640
Brandon
Job Details:
06/27/2018
Arrived on site for part hanger, the outer tub came with the bearings, I replaced the outer tub, unit tested good. Water lines were dry at time of service.
Near Austin, TX 78753
Joseph C.
Job Details:
06/26/2018
KRFC300ESS01 Arrived on site for “no ice production” complaint. Inspected unit and found ice maker supply tube clogged, due to faulty valve. Removed ice from tube. Removed and replaced dual valve. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Lorena, TX 76655
Arthur B.
Job Details:
06/26/2018
KUIC18NNZS0 (Ice Machine) - Arrived onsite to install sealed system components to ice machine from prior tech’s diagnosis. Removed cabinet and removed compressor and evaporator. Installed new replacements using braising methods. Vacuumed unit down to -25PSI. Charged system with 5.25oz of R134a refrigerant. Reassembled. Tested unit. Found good ice slab forming. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Lou
Job Details:
06/26/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the light wiring harness and tested and the unit still did not come on. I removed and replaced the main wiring harness and tested the unit and still, the unit did not operate. At this point, both wiring harnesses, the fuse board, and the main control have been replaced. I verified ohms at the transformer, the magnetron, capacitor, and diode and there is still no power to this unit. I verified voltage at the fuse board, the main power outlet and the power outlet that I was using while testing. I contacted my service manager CS and advised of my situation and he advised that the office would contact the warranty company and advise of the situation and Deem this unit non-repairable. I advised the customer that my service manager had been notified of this issue and that someone from the office would be contacting their warranty company. The customer advised that he would contact the office tomorrow. The
Near Austin, TX 78704
Joseph C.
Job Details:
06/26/2018
MDB4949SDZ0 Arrived on site for “no drain issue” complaint. Inspected unit and found disposal plugged. Removed plug and reconnected drain line. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Georgetown, TX 78628
Lou
Job Details:
06/26/2018
arrived on site to inspect washer over filling. Upon arrival, I found the unit outside in the garage unplugged. I verified that the sensor was working. I ohmed the water inlet valve and found that the valve is open. I advised the customer of my findings and quoted the customer $77.03 for the valve and TL270 $179.99 for service fee/Labor for a total of $278.22 including tax. Customer advised that they would pay the service fee of $108.24 today and wait to see what the insurance company wanted to do about servicing the unit. I advised the customer that the remaining total is $169.98 and that this quote is good for 30 days. No water leaks observed during service and unit remained in the garage unplugged.
Near Austin, TX 78717
Cliff
Job Details:
06/26/2018
Ge dishwasher GDT695SMJ0ES. Arrived on site to diagnose a dishwasher that will not turn on. Found main power wire burned at connection under dishwasher. This was causing no power to reach controls for unit. Repaired wiring and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Austin, TX 78727
Scott
Job Details:
06/26/2018
Maytag top load washer , not spinning
Near Woodway, TX 76712
Arthur B.
Job Details:
06/26/2018
WDF330PAHS0 (Dishwasher) - Arrived onsite for customer complaint of dishwasher not completing cycles and tripping breaker. Unplugged unit and removed toe plate to access junction box. Found wiring touching metal causing a short. Secured wiring nuts and reinstalled cover. Tested unit. Unit fills ,washes,drain and heats as intended. No other issues found. Was able to snap a picture of closing papers. MS advised that they can push thru. All water connections were dry at time of service.
Near New Braunfels, TX 78132
Connor M.
Job Details:
06/26/2018
WTW8500DW0 whirlpool washer Arrived on site to test unit for off balance loads found front right foot too close to drain recess in floor. Adjusted leveling foot and ran spin. Unit working properly, no leaks detected.
Near Spring Branch, TX 78070
Daniel A.
Job Details:
06/26/2018
ED5FHEXNB00 Not producing ice. Defective icemaker not going into harvest. Eplaced ice breaker. Verified normal ice production/water fill. Cleaned condenser coil. Normal operation after service
Near Woodway, TX 76712
Arthur B.
Job Details:
06/26/2018
KUIC18PNZS0 (Ice Machine) - Arrive onsite for customer complaint of of ice machine making too much ice. Ran ohm test on bin thermistor and found no ohms. Unit will new bin thermistor. P&L are as follows; WP2316399 (Bin Thermistor) $53.25, IM110 $149.99. Skyped EB to obtain authorization to proceed with repair. MS obtained authorization for repair. Removed bin thermistor and installed new replacement. Reverified ohms. Ohms check ok. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78628
Thomas L.
Job Details:
06/26/2018
Near New Braunfels, TX 78130
Connor M.
Job Details:
06/26/2018
WEE745H0FS whirlpool oven Arrived on site to test unit for error code. Found f2e1 indicating stuck/shorted key. Ran keyboard test and found all keys working. Customer stated this happened after a pot of water boiled over and some buttons got wet. This is normal. Ran full diagnostic test; unit passed. Job completed.
Near Georgetown, TX 78628
Thomas L.
Job Details:
06/26/2018
Near Leander, TX 78641
Thomas L.
Job Details:
06/26/2018
Arrived on site for no cooling in fresh food section. Found fan motor has failed . Replaced. No water hooked up to this unit.
Near Seguin, TX 78155
Connor M.
Job Details:
06/26/2018
MVWX655DW1 maytag washer Arrived on site to test unit for grinding during aggitate. Found gearcase failure. Replaced and tested unit. Unit working properly, no leaks detected.
Near Waco, TX 76712
Arthur B.
Job Details:
06/26/2018
WRX735SDHW00 (French Door Refrigerator) - Arrived onsite for customer complaint of French door refrigerator door mullion not closing properly. Found mullion does flip as intended. Was able to use silicone lubricant to lube hinges. Worked mullion. Mullion now flips open and closed as intended. No other issues found. All water connections were dry at time of service.
Near Woodway, TX 76712
Arthur B.
Job Details:
06/26/2018
KDTE204ESS4 (Dishwasher) - Arrived onsite for customer complaint of scratches in handle and panel of dishwasher. Found WPL provided new panel. Removed scratched panel and handle. Installed new replacements. Reassembled. Customer satisfied with new replacements. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Dona
Job Details:
06/26/2018
Arrived on site for dispenser not closing, found rod to spring mechanically not staying on any longer. Replaced dispenser and verified unit is running to spec. Ran unit through diagnostics checked for leaks, all water connections dry.
Dispenser-135.53
Labor-dw295-159.99
Tax24.38
Total 319.90
Near Seguin, TX 78155
Connor M.
Job Details:
06/26/2018
WOD51ES4ES00 whirlpool oven Arrived on site to replace failed tod. Replaced and tested. Upper oven still not baking. Confirmed control not sending voltage to elements. Part is expart. Office to schedule directly.
Near Austin, TX 78717
Thomas L.
Job Details:
06/26/2018
Removed and replaced in efficient compressor. New compressor started frosting the evaporator properly. Water connections were dry. Customer asked me to leave the unit pull forward so he could clean and wash behind it. All water connections are dry.
Near Austin, TX 78731
Cliff
Job Details:
06/26/2018
Whirlpool washer WTW4816FW2. Arrived on site to diagnose a washer that is leaking. Found hot water solenoid leaking internally. Replaced watervalve and tested unit. Found all is working properly at this time.
Near Austin, TX 78737
Robert
Job Details:
06/26/2018
WTW5000DW1 Arrived on job for complaints of water in tube and drain issue. Found valve on hot side failed to close completely and is dripping into tub. Replaced valve and run diagnostics. No errors found. No additional leaks detected. Job complete.
Near Seguin, TX 78155
Connor M.
Job Details:
06/26/2018
WRX735SDBH00 whirlpool refrigerator Arrived on site to install parts for repair. Installed separator, seal, and icemkaer kit. Unit working properly, no leaks detected.
Near Seguin, TX 78155
Connor M.
Job Details:
06/26/2018
MFF2558VEM10 maytag refrigerator Arrived on site to test unit arrived on site to install heater. Removed old heater and installed new one. New one is two inches too short. Installed anyway due to having to cut old one to get it out. Will pull on return visit. Reordering heater. Also found ice maker mold cracked and leaking into ice bin which wasnt mentioned on first visit. Ordering both parts for repair.
Near Round Rock, TX 78681
Jonathan S
Job Details:
06/26/2018
Whirlpool refrigerator model# WRS325SDHZ01. Not maintaining proper temperature in RC and dispensing
Near Elgin, TX 78621
Nathaniel B.
Job Details:
06/26/2018
Model ET8CHMXKB01, Arrived on call for buzzing noise from evap fan motor and returning to install new evap fan and seal were inside liner meets outer cabinet on both sections, replaced evap fan motor and sealed were inside liner meets outer cabinet on both sections all checks good, call complete.
Near Elgin, TX 78621
Nathaniel B.
Job Details:
06/26/2018
Model ET8CHMXKB01, Arrived on call for buzzing noise from evap fan motor and returning to install new evap fan and seal were inside liner meets outer cabinet on both sections, replaced evap fan motor and sealed were inside liner meets outer cabinet on both sections all checks good, call complete.
Near Georgetown, TX 78633
Dona
Job Details:
06/26/2018
Arrived on site for f21 error, unit is draining but will not move into spin cycle. Is turning counter clockwise then a slow clockwise 1 time. Pressure sensor is not engaging control to allow for wash or spin. Will need to replace pressure sensor with hose. Pump ohm correctly and seems to be draining each time but will need to bring with due to unit did stall a few times. All water connections dry.
Hose-12.84
Pressure sensor-170.90
Pump-190.80.
Labor is fl170 169.99
Total -589.45
Will return 6/28/18 Thursday
Collected 294.73 on card, customer will pay remaining 294.72 on return trip.
Near Waco, TX 76708
Arthur B.
Job Details:
06/26/2018
WRF989SDAE00 (French Door Dual Evaporator Refrigerator) - Arrived onsite to install water supply valve to refrigerator from prior tech’s diagnosis. Removed faulty water valve and installed new replacement. Reassembled. Tested. Found still no water dispensing. Removed cover and found water leaking from connection to housing and reservoir. Ordering. W11168758 (Reservoir) $26.54 and filter EDR2RXD1 (Filter) $53.27. R/S for Friday 6/29. MS approved our cost for reservoir due to misdiagnosis. Water turned off at this time.
Near Austin, TX 78745
Robert
Job Details:
06/26/2018
MVWC565FW1 Arrived on job to replace motor and capacitor. After replacement of capacitor test washer and operation is normal. No leaks detected at time of service.
Near Austin, TX 78703
Joseph C.
Job Details:
06/26/2018
WFW95HEDW0 Arrived on site for “door latch not unlocking” complaint. Inspected unit and found door latch defective. Per CS, no labor charges. Part is $97.72(pre-tax). Performed test of unit. Unit is performing as designed. No leaks detected, at time of service. Office to collect amount due with credit card, on file.
Near Austin, TX 78749
Luis
Job Details:
06/26/2018
Refrigerator-replaced separator to prevent ice from melting into drip tray
Near Round Rock, TX 78664
Jonathan S
Job Details:
06/26/2018
Whirlpool washer model# WTW5000DW. Not completing spin cycle.
Near Austin, TX 78745
Robert
Job Details:
06/26/2018
WET4024HW0 Arrived on job for complaints of dryer not running for more that a minute. Found wire issue at terminal block. Wrong voltage setup. Corrected miss wire and test dryer. Operation now normal.
Near Cedar Park, TX 78613
Lou
Job Details:
06/26/2018
arrived on site to inspect venthood color changed. Upon further inspection, I found that the top of the flu looks as if it got too hot or even caught fire (took pics). I removed the flu and inspected the inside and found it to look brand new; no burn marks. I advised the customer that he would need to contact Whirlpool customer care and see if the flu can be covered and replaced due to the issue being cosmetic and is not covered under warranty at this time. Job completed.
Near Austin, TX 78749
Luis
Job Details:
06/26/2018
Refrigerator-replaced starter to compressor
Near Cedar Park, TX 78613
Thomas L.
Job Details:
06/26/2018
Arrived on site for no ice condition. Found breaking icemaker harness. See pics. Replaced icemaker and cycled. All water connections dry.
Near Waco, TX 76708
Arthur B.
Job Details:
06/26/2018
KRFF507ESS01 (French Door Dual Evaporator Refrigerator) - Arrived onsite for customer complaint of French door refrigerator not cooling in RC section. Found RC evaporator all frosted up. Removed evaporator cover and used steamer to defrost evaporator. Found RC thermistor wire frayed. Installed new RC harness and reassembled. Found good air flow and frost pattern on evaporator. No other issues found. All water connections were dry at time of service.
Near Hutto, TX 78634
Jerry C.
Job Details:
06/26/2018
WEG745H0FS0 Arrived to inspect range not turning off. I found the customer was concerned about the unit running after bake operations were cancelled. I tested the unit to 350 within normal bake mode and the chassis cooling fan engaged at 155. I allowed a complete preheat and then cancelled. The fan ran until the compartment cooled. I advised the customer the issue is normal. I corrected a mounting hardware issue with the lower control panel. Operational test good, no gas leaks detected during service.
Near Austin, TX 78746
Kevin
Job Details:
06/26/2018
6/26/18 9:59: KB there 6/26 TUE, 9:02 to 9:30, Arrived on site and found icemaker is not completely dispensing production and it is falling behind lift fingers. Replaced ice maker and requested that customer continue to monitor it for correct operation. No water leaks from connections at time of service, job complete.; Job Cmpltd, snapped 4 QuickPics
Near Austin, TX 78746
Kevin
Job Details:
06/26/2018
Arrived on site and manually cycled icemaker but they did not fill with water, removed rear panel and found brown wire is Loose and not inside harness. Took one picture. After correcting harness voltage is now good to valve and manually fill the ice maker. No water leaks from connections at time of service, job complete
Near Georgetown, TX 78633
Dona
Job Details:
06/26/2018
Found f4 e4 error when trying to use sensor cooking, will need to replace humidity sensor. Discussed with home owner- with install above and venting sealed as so, builder will need to remove unit to be repaired. Discussed with CS as well, customer will call when unit has been uninstalled.
Near Dale, TX 78616
Connor M.
Job Details:
06/26/2018
RF364PXPQ2 whirlpool oven Door glass-110.41 CO210-169.99 arrived on site to test unit for broken outer glass. Found outer glass shattered. Replaced and tested unit. Unit working properly at time of service. Collected balance via cc.
Near Dale, TX 78616
Connor M.
Job Details:
06/26/2018
WED4815EW1 whirlpool dryer Arrived on site to install push to start for sticking. Voltage still not corrected. Electrician never even came out and tested. Motor circuit is getting 248vac and heater circuit is getting 0vac. Attached pic of volt meter with improper reading from white to black on sd mobile. Unit cannot be serviced again until it is verified they have their voltage fixed. Instruct on leaving unit unplugged until electrical system is serviced by an electrician.
Near Austin, TX 78723
Scott
Job Details:
06/26/2018
Arrived on site , replaced gear case and clutch . Ran calibration and diagnostics test , all checked good . No water leaks detected at time of service job complete .
Near Lakeway, TX 78734
Luis
Job Details:
06/26/2018
Refrigerator-replaced failed icemaker optics
Near Lago Vista, TX 78645
Thomas L.
Job Details:
06/26/2018
Arrived on site for improper upper rack operation. Found rack adjusters broken causing rack to fall. Replaced. All water connections were dry.
Near Leander, TX 78641
Lou
Job Details:
06/26/2018
arrived on site to inspect venthood light not working. Upon further inspection, I found that the light socket was loose and the light did not seat correctly inside the socket. I removed and replaced the light housing and tested and the light works. Job completed.
Near Leander, TX 78641
Lou
Job Details:
06/26/2018
arrived on site to inspect dishwasher not drying dishes. Upon further inspection, I placed the unit in diagnostics and tested the unit. The unit operated as designed. I recommended that the customer switch detergents from using pods to a liquid or liquid gel due to the pods producing too much suds. Also recommended the customer us rinse aid, which she does. Advised the customer that the unit is operating as designed and to use it on heavy mode and hi temp to assist in drying. No water leaks observed during service. Job completed.
Near Round Rock, TX 78665
Jonathan S
Job Details:
06/26/2018
Whirlpool refrigerator not dispensing ice.
Near Austin, TX 78730
Cliff
Job Details:
06/26/2018
Whirlpool microwave UMV1160CS3. Arrived on site to replace fan motor for microwave. Replaced motor and tested unit. Found all is functioning properly at this time.
Near Waco, TX 76710
Arthur B.
Job Details:
06/26/2018
KRFC704FPS00 (French Door Dual Evaporator Refrigerator) - Arrived onsite for customer complaint of RC section not cooling properly and frosting up. Removed lower shelve assembly and found evaporator frosted up. Removed all ice and installed updated control and new evaporator cover. Reassembled. Unit now cools as intended. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Dona
Job Details:
06/26/2018
Arrived on site for no operation, found wires blackened to cavity tco and primary door switch, not allowing connection to come in contact with switch. Removed charring around wiring. Allowing for wiring to make connection to tco and switch. Unit is now running, Wiring will need to be replaced, switches will need to be replaced, and cavity tco will need to be replaced.
Wiring harness-115.90
3 switches-60.35 each
Thermostat-70.70
Labor-mw110 harness replace-184.99 total of 598.23
Collected 598.23 on check 3860
Units breaker is turned off.
Will return Monday 7-2-18
Near Lago Vista, TX 78645
Thomas L.
Job Details:
06/26/2018
Arrived on site for leaking at door . Tested unit and all water connections were dry with no leaks.
Near Leander, TX 78641
Thomas L.
Job Details:
06/26/2018
Removed and replaced water valve per manufacturer recommendation. All water connections were dry.
Near Austin, TX 78724
Joseph C.
Job Details:
06/25/2018
KMHS120ESS4 Arrived on site for “door open/close door error” complaint. Inspected unit and found secondary switch faulty. Removed and replaced secondary switch. Tested unit. Unit is performing as designed.
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced ice maker and cycled. All functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced ice maker and cycled. All functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced ice maker and cycled. All functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced ice maker assembly. Cycled icemaker, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced ice maker assembly. Cycled icemaker, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced ice maker assembly. Cycled icemaker, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced supply board behind unit. Cycled refrigerator, all functions tested OK. Instructed customer to allow 24 hours for you to cool down completely. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced supply board behind unit. Cycled refrigerator, all functions tested OK. Instructed customer to allow 24 hours for you to cool down completely. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details:
06/25/2018
Arrived on site. Replaced supply board behind unit. Cycled refrigerator, all functions tested OK. Instructed customer to allow 24 hours for you to cool down completely. No leaks present. Job complete
Near Austin, TX 78724
Joseph C.
Job Details:
06/25/2018
KRFF507ESS01 Arrived on site for “leaking ice chute” complaint. Per my previous diagnosis, removed and replaced ice door. Found foam, from factory had been impeding proper closure of door, since new. Unit is performing as designed. No leaks detected, at time of service.
Near Taylor, TX 76574
Nathaniel B.
Job Details:
06/25/2018
Model GB2FHDXWS07, Arrived on call for ice in bottom floor of freezer, found drain tube is frozen, unit will need drain tube kit p-trap, part is covered by whirlpool, svc/labor rf210 169.99 plus tax 14.02 which = 184.01, customer agreed to est, installed drain tube and cleaned condenser coil and front grill, all checks good, no water leaks after repair, call complete, collected full balance of 184.01.
Near Taylor, TX 76574
Nathaniel B.
Job Details:
06/25/2018
Model GB2FHDXWS07, Arrived on call for ice in bottom floor of freezer, found drain tube is frozen, unit will need drain tube kit p-trap, part is covered by whirlpool, svc/labor rf210 169.99 plus tax 14.02 which = 184.01, customer agreed to est, installed drain tube and cleaned condenser coil and front grill, all checks good, no water leaks after repair, call complete, collected full balance of 184.01.
Near Georgetown, TX 78628
Lou
Job Details:
06/25/2018
arrived on site to inspect venthood fan not working. Upon further inspection, I turned the unit fan on low, medium and high. The only time the fan blower wheel came on was on high and it sounded as if it were rubbing against something. I removed the fan from the housing and loosened up the bolt and moved the fan blower wheel away from the motor and re-tightened and tested. The unit worked as designed; however, when the unit is on high speed, the blower wheel rubs against the housing due to it being badly warped. I notified the builder and advised of my findings and advised him that the office would contact him tomorrow to schedule return service. I ordered the fan blower motor assembly and office to reschedule return service due to part not available at this time.
Near Georgetown, TX 78628
Lou
Job Details:
06/25/2018
arrived on site to install previously diagnosed and ordered part. Removed and replaced the UI or control panel. Tested the unit in diagnostics and the unit operated as designed. I leveled the unit, also. Customer paid for service fee/labor at previous service on 06/21/18 DW135 $179.99 and total with tax was $194.84. No water leaks observed during service.
Near Round Rock, TX 78681
Chase
Job Details:
06/25/2018
WOS51EC0AS single oven had stored error code F1 e0. Heated oven to 350 degrees and all functions check good at this time. Error code is for main control but unable to duplicate any failures at this time
Near Leander, TX 78641
Chase
Job Details:
06/25/2018
WDF540PADM1 arrived on site to check dishwasher for not drying the dishes. Found several stored error codes, ran Diagnostics cycle and found heating element did not come on. Verified voltage out of the control and also found the heating element to be open. Replaced element and tested unit. Job complete
Near Austin, TX 78724
Joseph C.
Job Details:
06/25/2018
WRS325FDAB06 Arrived on site for “not cooling” complaint. Per my previous diagnosis, removed and replaced defrost control and thermostat. Unit is performing as designed. No leaks detected, at time of service.
Near Leander, TX 78641
Chase
Job Details:
06/25/2018
MMV5208AWS arrived on site to check microwave for not heating after loud pop was heard. Fuses, cavity thermostat and door switches all check good. Found unit with a very loud humming noise and high voltage components not coming on. Failure may have been caused by excessive Grease build up on high voltage components. Magnetron, capacitor and diode will be needed to repair the unit
Near Georgetown, TX 78633
Chase
Job Details:
06/25/2018
MDBH949AWS arrived on site to check dishwasher for no operation. Found the buttons on the left side of the control panel were unresponsive. Disassembled electronics and inspected the ribbon cable, and then reassembled. Was able to regain the left side button functions but start and cancel still do not work. Ran Diagnostics cycle to verify all other functions. Will need control panel to repair
Near Killeen, TX 76549
Arthur B.
Job Details:
06/25/2018
MVWB835DW1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer getting error code F6E1 and F6E2 errors. Found LED indicators dim when lit up. Found control and UI fault. Removed faulty components and installed new replacements. Ran test 052. Unit completed successfully. Advised customer to contact Lowes for her extended warranty for work to be covered. Claims to submit P&L to see which one comes first. All water connections were dry at time of service.
Near Temple, TX 76502
Dona
Job Details:
06/25/2018
Arrived on site for unit not washing, found unit will fill and drain, but never washes. Found seized motor on sump assy. Replaced sump with motor. Ran unit through diagnostics, unit checks good. All parms check good, all water connections dry.
Near Temple, TX 76502
Dona
Job Details:
06/25/2018
Arrived on site for noise throughout cycle, found unit is on pedestal. Found unit was severely off level. Noise is coming from washer to pedestal area. Leveled unit as best as possible. Ran unit with towels to verify no abnormal noises from within washer, shocks are good, pump and valve have no abnormal noises. Bearing does not sound abnormal. Unit is stabilizing in spin and wash. All water connections dry.