Service History 1781 - Appliance Express

Near Austin, TX 78717

Lou

Job Details: 06/13/2018

arrived on site to inspect microwave hood lamp not working. Upon arrival, the customer advised that she replaced the bulb with a whirlpool factory bulb and the unit does not light up in high, medium, but stays on low. I tested the light and could not get it to change brightness. I removed and replaced the main control and tested and the unit tested good. Job completed.

Near Georgetown, TX 78626

Thomas L.

Job Details: 06/13/2018

Arrived on site or uneven doors and noisy operation. Found unit very uneven which was causing the condenser coil to rattle. Level unit and doors and unit is now quiet.All water connections were dry.

Near Austin, TX 78744

Kevin

Job Details: 06/13/2018

Arrived on site and found left rear burner and left front burner are not igniting properly. Remove burner heads and caps and after reseating flames are now correct. Ensured all other functions are operating properly, job complete.

Near Austin, TX 78744

Kevin

Job Details: 06/13/2018

Arrived on site and set dishwasher into diagnostic cycle and found drain pump is rattling during operation. Removed drain pump and found packing debris making contact with impeller, after clearing noise has stopped and dishwasher is operating properly. No water leaks from connections at time of service, job complete.

Near Round Rock, TX 78665

Wesley

Job Details: 06/13/2018

Repairing recessed interlock on OTR microwave.

Near Kyle, TX 78640

Robert

Job Details: 06/13/2018

MDE5500AYW Arrived on job to replace rollers and idler pulls for noise complaints. After replacement of parts operation normal. Dryer heating and air movement good. Job complete.

Near Austin, TX 78758

Scott

Job Details: 06/13/2018

Arrived on site for dead keypad . Found keypad would respond to ouch commands and heat but digital display was completely out ,checked all connections . Panel has just no read out . Ordering panel control. Return 6/19

Near Hutto, TX 78634

Nathaniel B.

Job Details: 06/13/2018

Model WMH53520CS5, Arrived on call for microwave power cord burned and socket burned when microwave is in use, found that fuse is not blown on filter board, found power cord and outlet burned see pic, saw no other damage to harnesses on inner compartment behind control area, will need power cord and filter board, and customer will need to contact a electrician to have outlet replaced and to verify polarity at the outlet to verify wired correctly, skyped office parts and talked to susan and will reschedule for 6/15/18

Near Hutto, TX 78634

Nathaniel B.

Job Details: 06/13/2018

Near Kyle, TX 78640

Leonardo

Job Details: 06/13/2018

Whirlpool range right front burner not igniting model: WFG530S0ES1. Arrived on site to test unit for right front burner not igniting. Test unit and found weak ignitor, replaced right front burner with ignitor test unit and burner igniting right away job complete no leaks present at this time.

Near Kyle, TX 78640

Leonardo

Job Details: 06/13/2018

Whirlpool microwave inside light flickering model: WMH31017FS0. Arrived on site to test unit for inside light flickering. Test unit and found bad 3 way switch. Replaced 3 way switch test unit and unit test good job complete.

Near Georgetown, TX 78628

Thomas L.

Job Details: 06/13/2018

Arrived on site for no ice condition. Unit was tuned off. Entered diagnostics and all operations tested correctly. Turned unit into normal on position andtested to find defective ui.

We serviced a

Arrived on site for door not latching correctly. Tub shape is causing door not to close properly. Hinges are$96.27 each if needed.

Near Georgetown, TX 78628

Thomas L.

Job Details: 06/13/2018

Sarah assisted. Office to reschedule

Near Killeen, TX 76542

Steve C.

Job Details: 06/13/2018

Near Buda, TX 78610

Kevin

Job Details: 06/13/2018

Arrived on site and found microwave is noisy when fan is running, disassemble the microwave and sound construction debris is making contact with fan blades. After clearing blades noise has stopped and microwave is operating properly, job complete.

Near Georgetown, TX 78628

Lou

Job Details: 06/12/2018

arrived on site to install previously diagnosed and ordered parts. Removed and replaced the convection fan and both the upper and lower door gaskets. Tested unit and unit continued to make a vibrating noise but was not as loud as the first visit. I pulled the unit and repositioned the power cord and tested again. The noise was still there at the same tone. The sound appears to be coming from the blower. The customer was okay with the sound but I advised the customer should the noise get louder to call the office and request a tech to come back. Should this have to happen, I would recommend that two techs go to the call due to the area where the unit is located. The unit is next to the refrigerator and is in a small tight place and difficult to remove from wall without damaging the refrigerator, the wall or molding around the unit. Job completed.

Near Austin, TX 78757

Scott

Job Details: 06/12/2018

Arrived on site for fresh food section being warm . Found evap fan had fallen out on rear mounting of bracket . Which caused fan to tilt and blades to lock up on mounting burning out motor . Replaced fan and cold air is now blowing into fresh food section . No water leaks detected at time of service

Near Austin, TX 78754

Joseph C.

Job Details: 06/12/2018

WDT730PAHZ0 Arrived on site for “not powering on” complaint. Inspected unit and found wire nuts too big and had come off connections in junction box. Installed new correct size wire nuts. Tested unit. Unit is performing as designed. No leaks detected, at time of service.

Near Round Rock, TX 78681

Lou

Job Details: 06/12/2018

arrived on site to install previously diagnosed and ordered parts. Removed and replaced the dryer kit and tested. Unit tested good. Customer advised that since the first service call, the timer stopped working and will not advance while in automatic dry-miser mode. I tested unit in such mode and the timer did not advance. Customer also advised that the LEDs on the clean touch switch stopped working. Office to order timer and switch and schedule return service LSO. No lint observed during service.

Near New Braunfels, TX 78132

Connor M.

Job Details: 06/12/2018

WED96HEAC0 whirlpool dryer Arrived on site to install parts for repair. Imstalled full dryer kit and drum. Unit working properly. Made aware of proper venting and fire hazard.

Near Austin, TX 78717

Wesley

Job Details: 06/12/2018

Lighting failure in vent hood.

Near Buda, TX 78610

Kevin

Job Details: 06/12/2018

Arrived on site and found washing machine is disconnected from power, when reconnected wash light is blinking. Held start button down until this clear and set washer into diagnostic cycle and found No saved error codes. I ran all functions and manual diagnostic and everything checks good. Hilarity and voltage on out let’s is correct. Ran automatic test cycle and everything checks good, ran a calibration cycle and it completed properly. spoke with techline kathy, there are no known issues, and tech line did not have any recommendations. Requested that customer continue to monitor operation, no water leaks from connections at time of service, job complete

Near Round Rock, TX 78681

Lou

Job Details: 06/12/2018

arrived on site to inspect dryer with something lodged inside the vent. Upon arrival, the customer advised that he was cleaning out the vents with his vacuum and the hose connector came loose and fell down inside the vent. Upon further inspection, I found that the hose connector had fallen down ink the vent and got lodged in the blower wheel. Customer advised that he had not used the unit since this occurred. I inspected the blower wheel and housing and all looked good. No lint observed during service.

Near New Braunfels, TX 78132

Connor M.

Job Details: 06/12/2018

KSC24C8EYW02 kitchenaid refrigerator Arrived on site to test unit for not cooling. Found both compartments cooling well. Cycled freon valve and found it getting stuck. Would not send freon to rc evap. No signs of leaks. Cimpressor running hot, will replace as a precaution. Parts and labor covered in entitlement. Will need 3 hours for repair. Office to schedule directly.

Near Austin, TX 78726

Cliff

Job Details: 06/12/2018

Whirlpool dishwasher WDT720PADM1. Arrived on site to diagnose a dishwasher that is not cleaning properly. Tested unit and found pump assembly receiving power but not operating. Pump is shorted out due to normal wear and tear. Replaced pump assembly and tested unit. Found all is functioning properly at this time. No leaks were found after services were performed.

Near Briggs, TX 78608

Thomas L.

Job Details: 06/12/2018

Arrived on site for unit not cycling off when full. Tested bin thermistor to find it way out of operating range. Replaced. Water connections were dry.

Near Austin, TX 78759

Scott

Job Details: 06/12/2018

Arrived on site , replaced pads 30.24,dispenser motor 122.50and ice maker189.21,labor 130.00. Collected 510.89cc w/tax. No water leaks detected at time of service . Kitchen aid built in fridge 48in sxs

Near Austin, TX 78737

Luis

Job Details: 06/12/2018

Refrigerator-installed control kit including main control and ui

Near San Marcos, TX 78666

Connor M.

Job Details: 06/12/2018

KUWL204ESB00 kitchenaid wine cooler File number-7722210769 comtrol-289.41 customer trying to get labor covered through kitchenaid. Arrived on site to test unit for not cooling. Found all lights on UI turned on and non repsonsive. Techline said to replace control. Ordering for return. Ja approved 6/18

Near Round Rock, TX 78681

Nathaniel B.

Job Details: 06/12/2018

Model WRT311FZDW00, Arrived on call for freezer door warped not allowing freezer door to seal, replaced freezer door and installed name plate, and also sealed were the inside liner meets outer cabinet due to large gaping which was creating air leak, all checks good, call complete, no water leaks at time of call.

Near Round Rock, TX 78681

Nathaniel B.

Job Details: 06/12/2018

Near Austin, TX 78745

Robert

Job Details: 06/12/2018

MEDC215EW1 Arrived on job to replace motor and blower. After replacement of parts test dryer noise normal.

Near Killeen, TX 76549

Thomas L.

Job Details: 06/12/2018

Arrived on site for improper temperatures. Found sensor out of range. Replaced sensor to achieve proper baking temperatures

Near Buda, TX 78610

Luis

Job Details: 06/12/2018

Refrigerator-replaced failed icemaker

Near Round Rock, TX 78664

Nathaniel B.

Job Details: 06/12/2018

Model SF304PEEW0, Arrived on call for oven only reached 200 degrees and will not go any higher, checked bake igniter and when set to 350 degrees would not light the flame pulling 1.9 amps which is to low replaced bake igniter and know flame is lighting as it should, preheated the oven to 350 degrees and u it did preheat to 350 degrees, all checks good, call complete, no gas leaks at time of call, call complete.

Near Round Rock, TX 78664

Nathaniel B.

Job Details: 06/12/2018

Near Georgetown, TX 78633

Jerry C.

Job Details: 06/12/2018

KRFF707ESS01 Arrived to inspect ice in fc. I found the issue was with a large mass of ice within the floor area of the rc. I removed the ice and corrected the drain tube being frozen and tested. The drain tube connection at the rear of the unit was hanging down, allowing a large amount of air to thermosiphon up into the rc evaporator area. I corrected the drain tube issue and discovered the ice maker housing incorrectly installed and corrected. Operational test good, no leaks observed during service.

Near Austin, TX 78748

Leonardo

Job Details: 06/12/2018

Whirlpool gas stove model: WFG525S0HZ0 damaged panel. Arrived on site to test unit for damaged panel. Found damaged panel replace panel test unit and unit test good job complete no leaks present at this time

Near Round Rock, TX 78665

Nathaniel B.

Job Details: 06/12/2018

Model WED5100VQ1, Arrived on call for dryer not drying cloths very little heat, found that dryer is still heating, found wall vent is restricted, customer to not run dryer till wall vent is cleared due to this is a fire hazard, customer to call dryer wall vent cleaning service. No parts needed, call complete.

Near Round Rock, TX 78665

Nathaniel B.

Job Details: 06/12/2018

Near Austin, TX 78749

Kevin

Job Details: 06/12/2018

Arrived on site and found Ice drawer in the freezer is stuck in place, are used steamer on the right rail and it has freed up and is now moving properly. No further repair is required at this time no water leaks from connections at time of service, job complete.

Near Canyon Lake, TX 78133

Connor M.

Job Details: 06/12/2018

GU2300XTVB0 whirlpool washer Arrived on site to test unit for heating issues. Found heater working fine. No rinse aid being used. Lower rack not from a whirlpool model. Cannot service. No leaks detetced.

Near Austin, TX 78738

Brandon

Job Details: 06/12/2018

Arrived on site for water leaking onto floor, found clog in the duck bill, I removed the clog and cleared the drain line unit tested good.

Near Austin, TX 78704

Robert

Job Details: 06/12/2018

WFG505M0BS0 Arrived on job for complaints of not heating Found bake igniter temperature too low. Replaced igniter and test. Operation normal. Igniter and labor

Near Pflugerville, TX 78660

Nathaniel B.

Job Details: 06/12/2018

Model KVUB606DSS3, Arrived on call for vent hood red wire on led light broke not allowing lights to come on, replaced right side led light and all checks good all vent hood lights are working know, call complete.

Near Pflugerville, TX 78660

Nathaniel B.

Job Details: 06/12/2018

Near Canyon Lake, TX 78133

Connor M.

Job Details: 06/12/2018

WRT311FZDW00 whirlpool refrigerator 7722208104 arrived on site to install parts for repair. Unit completely empty of freon. Not enough time passed for dye to circulate in system. No leaks found anywhere with blacklight. Found steel coming from cabinet for filter direr cut too short and split. Cannot install new drier. Cap tube too short as well. Called techline and was told unit is non repairable. Job completed.

Near Austin, TX 78723

Joseph C.

Job Details: 06/12/2018

WRS325SDHZ00 Arrived on site for “fresh foods door clanging as it closes” complaint. Inspected unit and found to be unlevel. Leveled unit. Unit is performing as designed. No leaks detected, at time of service.

Near Austin, TX 78717

Lou

Job Details: 06/12/2018

arrived on site to inspect microwave turntable not working. Upon further inspection, I checked ohms at the turntable motor and found it open. I removed and replaced the motor and tested the unit. Unit operates designed. Job completed.

Near Austin, TX 78737

Leonardo

Job Details: 06/12/2018

Whirlpool gas cooktop model: WCG51US0DS00 flames not going to low. Arrived on site to test unit for flames not going to low. Adjusted flames on right front and back and left back burner. No leaks present job complete

Near Killeen, TX 76542

Thomas L.

Job Details: 06/12/2018

Arrived On site for noisy operation.unit has a very Noisey drive motor which cuts off after approximately 5 minutes of use. Use cool down before it starts again . Erica assisted. Customer needs Friday with an a.m. request.

Near Austin, TX 78704

Robert

Job Details: 06/12/2018

WTW8000DW2 Arrived on job for complaints of not starting cycle. Found the lid lock damaged internal and not locking. Replaced lid lock and test operation normal. No leaks detected at time of service. Job complete

Near West Lake Hills, TX 78746

Kevin

Job Details: 06/12/2018

6/12/18 8:51: KB there 6/12 TUE, 8:00 to 8:25, Arrived on site and inspected dryer and found no power showing at terminal block. Inspected breakers and found they are tripped but do not look it. Flip the breakers all the way off and then all the way on and power has returned to dryer. It is heating properly and airflow is good, job complete.; Job Cmpltd, snapped 2 QuickPics

Near West Lake Hills, TX 78746

Kevin

Job Details: 06/12/2018

Arrived on site and found freezer temp is 3-4 degrees took 1 picture. Fresh food temp is 40, Removed evaporator cover and found frost pattern looks good. Took one picture. Spoke with CS will bring back thermostat to address intermittent not cooling, no water leaks at time of service.

Near Lakeway, TX 78738

Brandon

Job Details: 06/12/2018

Arrived on site for customer complaint of non stop clicking coming from igniter. I found unit was unplugged when I arrived, I plugged unit in and turned gas on, unit tested good. Collected 108.24 on cc

Near Austin, TX 78717

Lou

Job Details: 06/12/2018

arrived on site to inspect water dispenser leaking. Upon further inspection, I found that the filter housing was cracked and the filter was an aftermarket filter which was not seating correctly. I removed and replaced the filter housing and quoted the customer $61.49 for this filter and with tax the total was $66.56 and the customer agreed to purchase the filter. Replaced the filter with whirlpool approved filter and tested unit and unit tested good. No water leaks observed during service.

Near Austin, TX 78717

Lou

Job Details: 06/12/2018

arrived on site to install previously diagnosed and ordered parts. I removed and replaced the main control and UI console and tested the unit. Unit operated as designed. There were an abundance of detergent suds during diagnostics and there was no detergent added. I recommended to the customer that they not use detergent pods and switch to a liquid or liquid gel and to use no more than two teaspoons per wash to prevent too much suds. I also leveled the unit due to the left side of the door rubbing badly. No water leaks observed during service. Job completed.

Near Killeen, TX 76543

Thomas L.

Job Details: 06/12/2018

Arrived on site for improper cycle times. Calibrated control. Tested unit . Removed and replaced defective lid latch. All water connections were dry.

Near Canyon Lake, TX 78133

Connor M.

Job Details: 06/12/2018

MEDX655DW0 maytag dryer Arrived on site to test unit for non responsive. Fiund no voltage to dryer. Breaker flipped. Tunred breaker on and checked voltage and all components. Unit working properly. Likely due to a heavy load. Made aware of proper venting and and fire hazard.

Near Austin, TX 78745

Luis

Job Details: 06/12/2018

Refrigerator-repaired filter housing

Near Austin, TX 78739

Leonardo

Job Details: 06/12/2018

Whirlpool dishwasher model: WDF310PAAS4 not drying dishes. Arrived on site to test unit for not heating or drying dishes. Test unit and found broken heater. Replaced heater test unit and unit test good job complete no leaks present at this time.

Near Copperas Cove, TX 76522

Thomas L.

Job Details: 06/12/2018

Removed and replaced failing trucks and wheels to allow proper rack operation . All water connections were dry.

Near Austin, TX 78753

Scott

Job Details: 06/12/2018

Arrived on site for no water coming into unit . Found water was not turned on fully at shut off valves . Ran diagnostics cycle, all tested normal . No error codes . No water leaks detected at time of service . Job complete .whirlpool front load washer .

Near Canyon Lake, TX 78132

Connor M.

Job Details: 06/12/2018

KRFF507ESS01 kitchenaid refrigerator Arrived onnsite to test unit for frost build up in freezer on drawer. Found significant amountof frost build up on left and right side of tracks, and under bin. Fiund gaslet that was oreviously replaced separates from door liner when pulled open due to magnet. Found not properly re install gasket due to the gap between door liner and stainless. Will need to replace freezer door. Please allow 2 hours to defrost and seal gasket on return. Office to scheudle directly.

Near Georgetown, TX 78633

Mike C.

Job Details: 06/12/2018

Kitchen Aid dishwasher KDTE254ESS0 Arrived to find unit with no operation. Checked voltage at control and found no voltage. Opened junction box and found the black wire had come out of the wire nut. Re stripped wires and put a new wire nut on wire. Checked operation and unit checks good with no water leaks. DW600 $129.99 ($10 senior discount)

Near Dripping Springs, TX 78620

Brandon

Job Details: 06/12/2018

Arrived on site for customer complaint of not dispensing ice, found power getting to auger motor, found bad motor, I replaced the motor, unit tested good. Water lines were dry at time of service.

Near Round Rock, TX 78665

Nathaniel B.

Job Details: 06/12/2018

Model WRX988SIBM03, Arrived on call for both sections not cooling properly, food is unthawing in freezer section, found temps today are 39 degrees. In fresh food section and 0 degrees in the freezer, found that customer is on the correct breaker for the unit but the unit has a extension cord running from the units power cord to the outlet due to fridge power cord is not long enough to reach the outlet , and sensors and fans all check good, called whirlpools tech line and talked to bruce file number 7722204563, unit must have a dedicated outlet and can not be on a extension cord, per bruce from whirlpool tech line customer will need to contact a electrician to have a outlet put in for the fridge, also customer had a complaint of water on mid drawer floor and running out on to the top of the freezer door gasket, turned on all mullion heaters to 100 percent run time but saw no water on bottom floor of mid drawer unit is draining as it should in fresh food section. Also instructed custome

Near Round Rock, TX 78665

Nathaniel B.

Job Details: 06/12/2018

Near Austin, TX 78750

Cliff

Job Details: 06/12/2018

Kitchenaid oven combo KOCE507ESS06. Arrived on site to diagnose and I’ve been with that door that is not closing properly. Tested unit and found no mechanical failures to oven door or hinges at this time. Advised homeowner on door operation and informed on how bumpers are installed on cavity to prevent door from contacting racks. No further repairs are needed, and all is working properly at this time.

Near New Braunfels, TX 78132

Connor M.

Job Details: 06/12/2018

Arrived on site to test unit for not tripping breaker. Found unit on arch fault protected breaker. Ran amp draw on all functions. Amp draw never out of range. Instruct on manufacturer testing done only on conventional breakers. Breaker will need to be swapped with regular breaker per the manufacturer. No leaks detected.

Near New Braunfels, TX 78132

Connor M.

Job Details: 06/12/2018

MVWC200BW1 maytag washer Arrived on site to install parts for repair. Found unit operating as designed. Customer chose not go forward with repair. Collected service only. 99.99. No leaks detected.

Near Austin, TX 78741

Kevin

Job Details: 06/12/2018

Arrived on site and inspected dryer and found no power showing at terminal block. Inspected breakers and found they are tripped but do not look it. Flip the breakers all the way off and then all the way on and power has returned to dryer. It is heating properly and airflow is good, job complete.

Near Georgetown, TX 78633

Mike C.

Job Details: 06/12/2018

Whirlpool Oven WOS51EC0AS04 Arrived to find unit with no display or operation. Removed control panel and checked thermal fuse for continuity and found it bad. Installed new thermal fuse and checked operation, checked good.

Near Copperas Cove, TX 76522

Thomas L.

Job Details: 06/12/2018

Removed and replaced microwave lightbulb.

Near Georgetown, TX 78633

Lou

Job Details: 06/11/2018

arrived on site to install previously diagnosed and ordered parts. Removed and replaced the rc thermistor, main control, and UI. Tested unit and unit began to cool as designed. No water leaks observed during service.

Near New Braunfels, TX 78132

Daniel A.

Job Details: 06/11/2018

JMC2430DS00 f2e1. No response from touchpad. Error code for console. Replaced touchpad/console assembly. Programmed unit. Verified normal operation after service.

Near Taylor, TX 76574

Nathaniel B.

Job Details: 06/11/2018

Model WRS325FDAM04, Arrived on call for interior lights not coming on, found upper fresh food led and freezer led were bad, replaced both due to had 124 ac volts to the fresh food upper led but none of the lights were working, and after installing freezer and top fresh food led all lights are working as they should, no water leaks at time of call, call complete.

Near Taylor, TX 76574

Nathaniel B.

Job Details: 06/11/2018

Near New Braunfels, TX 78130

Connor M.

Job Details: 06/11/2018

MVWC200BW1 maytag washer Arrived on site to install parts for repair. Found unit operating as designed. Customer chose not go forward with repair. Collected service only. 99.99. No leaks detected.

Near Round Rock, TX 78665

Nathaniel B.

Job Details: 06/11/2018

Model MFI2570FEB01, Arrived on call for ice maker not making ice, found that ive maker fill cup is frozen and fill tube frozen not allow water dispense to ice maker for production, will order dual valve and use ice-maker on return, skyped office parts and talked to kristen and will reschedule for 6/14/18

Near Round Rock, TX 78665

Nathaniel B.

Job Details: 06/11/2018

Near Niederwald, TX 78640

Robert

Job Details: 06/11/2018

WFC150M0EB0 Arrived on job for complaints of f9 code. Check wiring for error non found. Replace control and tested heating correct.

Near San Marcos, TX 78666

Connor M.

Job Details: 06/11/2018

WRF736SDAM10 whirlpool refrigerator Valve-89.23 labor-179.99 arrived on site to replace parts for repair. Found ice being ejected from mold in solid strips. Indicating mold filling with too much water. Small amount of water overflowing into ice bin each fill. Pressure checked fine. Will need dual water valve to repair. Ja approved friday. Customer requesting 3-6

Near Elgin, TX 78621

Joseph C.

Job Details: 06/11/2018

WFW75HEFW0 Arrived on site for “noise coming from basket area” complaint. Inspected unit and found debris between basket and tub. Cleared debris. Tested unit. Unit is performing as designed. No leaks detected, at time of service.

Near Pflugerville, TX 78660

Nathaniel B.

Job Details: 06/11/2018

Model WDF330PAHS0, Arrived on call for top left door when closed is not sealing, found inner door panel was warped not allowing door to seal, replaced inner door and pads and tested and all checks good, call complete, no water leaks after repair, also instructed customer to let maintenance no the the kitchen sink is not sealing to the cabinet and is leaking water under sink, did instruct the apartment office. Call complete.

Near Pflugerville, TX 78660

Nathaniel B.

Job Details: 06/11/2018

Near Burnet, TX 78611

Thomas L.

Job Details: 06/11/2018

Arrived on site for no turntable operation. Found driver and support not fitting into motor shaft properly thus causing dish not to turn.

Near Buda, TX 78610

Robert

Job Details: 06/11/2018

WTW6700TW1

Near Pflugerville, TX 78660

Scott

Job Details: 06/11/2018

Arrived on site for dishwasher making loud grinding noise . Still pumping but weak spray and making a very loud grinding noise . Will need sump &motor . Will need autho . Part @ 224.86 ,dw120/mt350 @ 204.99. Please bill 99.99 to CC on file . All prices are pretax . No water leaks detected at time of service . Will need autho on repair . Kitchen aid dishwasher

Near Cedar Park, TX 78613

Lou

Job Details: 06/11/2018

arrived on site to inspect washer dispenser molded. Upon further inspection, I found that mold was built up inside the dispenser and around the sensor. I removed and replaced the dispenser and tested the unit. Unit operated as designed. I zip tied the drain tube to the water hose to secure it from coming out of the drain pipe. No water leaks observed during service.

Near New Braunfels, TX 78132

Diego G.

Job Details: 06/11/2018

Arrived on site. Replaced thermistor, UI and fan scroll. Ran diagnostic test, all functions tested OK. No leaks present. Job complete

Near New Braunfels, TX 78132

Diego G.

Job Details: 06/11/2018

Arrived on site. Replaced thermistor, UI and fan scroll. Ran diagnostic test, all functions tested OK. No leaks present. Job complete

Near New Braunfels, TX 78132

Diego G.

Job Details: 06/11/2018

Arrived on site. Replaced thermistor, UI and fan scroll. Ran diagnostic test, all functions tested OK. No leaks present. Job complete

Near Marble Falls, TX 78654

Thomas L.

Job Details: 06/11/2018

Replaced failed ice bin

Near Marble Falls, TX 78654

Thomas L.

Job Details: 06/11/2018

Replaced failed defrost bimetal.all water connections were dry. All freezer lights are defective, $81.40 each, customer declined to replace lights.

Near Leander, TX 78641

Jerry C.

Job Details: 06/11/2018

ED5PVEXWS08 Arrived to inspect ice in bottom of fc. I found the drain tube blocked with debris. I removed the ice from the fc compartment and then cleared the tube. I tested and normal operation resumed. No leaks observed during service.

Near Buda, TX 78610

Robert

Job Details: 06/11/2018

WFG510S0AS1 Arrived on job for complaints of not keeping temperature. Found igniter not always lighting. Quote customer labor CO270 $159.99 and igniter $57.48. Replaced igniter and test light every time

Near Austin, TX 78748

Connor M.

Job Details: 06/11/2018

WED4815EW1 whirlpool dryer Installed new timer and tested unit. Unit working properly. Instruct on proper venting and fire hazard.

Near Marble Falls, TX 78654

Thomas L.

Job Details: 06/11/2018

Removed and replaced failed ice bin. Water connections were all dry.

Near Leander, TX 78641

Lou

Job Details: 06/11/2018

arrived on site to install previously diagnosed and ordered part. Attached a new nameplate to the venthood. Job completed.