Service History 1699 - Appliance Express

Near Round Rock, TX 78664

Lou

Job Details: 12/31/2018

DRYER WHIRLPOOL WGD7500GW0 "- arrived on site to install previously diagnosed and ordered parts. Due to the dryer door not closing properly, the front panel, inner door panel, both hinges, both springs, and a strike were ordered. I removed and replaced all parts ordered and tested the unit. The door closed and sealed good. I turned the unit on and the door remained closed. I advised the customer to not slam the door or rest anything on the door as it would cause damage again. Also advised that when closing the door, to push in the top middle of the door where the strike is located. No lint observed during service, job completed."

Near Georgetown, TX 78633

Jerry C.

Job Details: 12/31/2018

DISHWASHER GE GSD4020Z07BB "GSD4020Z07BB Arrived to inspect water leak. I found the source of the water damage to adjacent cabinets to be the gate valve assembly within the sump assembly.. I advised the customer to not attempt use until the repair is completed. No leaks of the water supply observed during service. ; ordrng 1 WD26X10013 (motor/pump assy)"

Near Waco, TX 76712

Arthur B.

Job Details: 12/31/2018

DISHWASHER WHIRLPOOL WDT720PADM2 Arrived onsite for customer complaint of dishwasher not starting. Ran diagnostics and found error code F7E1 (Heater Short). Cleared error code and ran test cycle. Poured water on heater. Water was sizzling off. Advised customer to run hot water at sink before starting cycle to allow dishes to clean properly. No other issues found. All water connections were dry at time of service.

Near Bastrop, TX 78602

Joseph C.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRS588FIHZ00 "Arrived on site for “loose door handle” complaint. Tightened set handle screws and leveled unit. Unit is performing as designed. No leaks detected, at time of service."

Near Austin, TX 78702

Luis

Job Details: 12/31/2018

REFRIGERATOR GE PYE22KELEDS "Arrived on site for not dispensing water. Removed connections to filter water flowing correctly,reconnected in,eta disconnected outlet line. Had customer engage water dispenser,water dispensing from outlet line of filter housing. Reconnected line diagnosed frozen line in door, customer will defrost unit to defrost line."

Near Wimberley, TX 78676

Kevin

Job Details: 12/31/2018

REFRIGERATOR GE HA10TG31SW "Arrived on site and added recall kit to refrigerator, recommended that customer allow 10 to 12 hours for refrigerator to cool properly, job complete"

Near Buda, TX 78610

Kevin

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW8900BC0 "Arrived on site and inspected washing machine and found previous attempt to replace bearing has failed and possibly caused damage to bearing and shaft Location in tub. Replaced outer tub and ran a diagnostic cycle to confirm the correct operation. No water leaks from connections at time of service, job complete reported situation to CS and MS."

Near Leander, TX 78641

Lou

Job Details: 12/31/2018

DRYER MAYTAG MEDX655DW1 "arrived on site to inspect dryer making loud noises. Upon further inspection, I found that the customer was drying some clothes. I did not hear the noise at first, so I stopped the dryer tarted it and immediately, I could hear the squeaking noise. The customer advised that it would get much louder. I lifted the top panel to expose the drum and turned the unit on and could hear the noise coming from the back right roller area. I removed the drum and found that both back rollers/axles were dirty. I removed and replaced the rollers and tested them and they rolled without any issues. I replaced the belt also as it was beginning to fray in places. I put the unit back together and tested it and it operated as designed and was quiet. No lint observed during service, job completed."

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

COOKTOP WHIRLPOOL GCI3061XB01 "Arrived on site. Replaced module and display. Configurated unit and cycled all burners, all functions tested OK. No leaks present. Job complete"

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

COOKTOP WHIRLPOOL GCI3061XB01 "Arrived on site. Replaced module and display. Configurated unit and cycled all burners, all functions tested OK. No leaks present. Job complete"

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

COOKTOP WHIRLPOOL GCI3061XB01 "Arrived on site. Replaced module and display. Configurated unit and cycled all burners, all functions tested OK. No leaks present. Job complete"

Near Burnet, TX 78611

Thomas L.

Job Details: 12/31/2018

REFRIGERATOR MAYTAG MFI2568AES Arrived on site For no ice condition and freezing in fresh food section. Replaced gasket at ice box container to illuminate freezing air into the fresh food section. Replaced ice maker and water valve to stop the icing build up in the icebox compartment. All water connections were dry.

Near Austin, TX 78739

Robert

Job Details: 12/31/2018

OVEN KITCHENAID KEMC377KSS03 Arrived on job for complaints of not cooking. Found thermal fuse open and light in microwave out. ; ordrng 1 WP9759243 (thrmst-fix) and 1 WPW10440740 (lmp-basles)

Near Cedar Park, TX 78613

James

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KBSD608ESS00 Arrived on site and installed new freezer door. Verified all water connections are dry and not leaking. Unit working properly. Job complete

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

RANGE WHIRLPOOL WFE515S0ES1 "Arrived on site. Check for no display issues. Found 120 V going to control but not lighting up. Replaced control and cycle, all functions tested OK. Job complete"

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

RANGE WHIRLPOOL WFE515S0ES1 "Arrived on site. Check for no display issues. Found 120 V going to control but not lighting up. Replaced control and cycle, all functions tested OK. Job complete"

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

RANGE WHIRLPOOL WFE515S0ES1 "Arrived on site. Check for no display issues. Found 120 V going to control but not lighting up. Replaced control and cycle, all functions tested OK. Job complete"

Near Leander, TX 78641

James

Job Details: 12/31/2018

VENTHOOD WHIRLPOOL UXT4236ADS2 "Arrived on site and inspected damage. I found the filter missing, fan blade missing, light socket harness melted, light cover missing and filter latch melted. Cover for light shows not available. Customer has decided to get a new unit. Collected diagnosis"

Near Austin, TX 78759

Scott

Job Details: 12/31/2018

DISHWASHER KITCHENAID KDTE304GPS0 "Arrived on site for soap staying at bottom of tub . Ran diagnostics got 6-4 error code . Found triac fuse open on float switch . Switch and float good . Ordering control . Wash motor and heater working in diagnostics mod . During reg wash cycle unit will wash and then drain , heater doesn’t come on . Nonwater leaks detected at time of service . Please call to set return date.; ordrng 1 W11305303 (CONTROL)"

Near Austin, TX 78748

Leonardo

Job Details: 12/31/2018

DISHWASHER WHIRLPOOL WDT730PAHZ0 Arrived on site to test unit for unit not washing. Test unit and found bad wash motor. Replaced sump and motor test unit an dunit test good. No leaks present at this time.

Near Austin, TX 78739

Kevin

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRS325SDHZ02 "Arrived on site and found doors are not correct, leveled doors and took one picture and they are now correct. No water leaks from connections at time of service, job complete"

Near Austin, TX 78759

Scott

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID WRV986FDEM01 "Arrived on site ,replaced all boards per Paul with power off . Deli is not lighting up . Will need pantry harness . Will need parts research , can’t find harness in break down . Ran diagnostics , all checked good .No water leaks detected at time of service . Please call to set return .; ordrng 1 CNOTES and 1 PARTSRESEARCH"

Near Georgetown, TX 78628

Steve C.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW7340XW0 Arrived on site for the unit is making noise. Tested the unit and found the unit is making a thumping noise when spinning. Remove the rotor and stator And it’s still making the noise. Also remove the wash plate and it still making the noise. Found the bearings are defective on the unit. Quoted the customer for the part and labor and customer will call us if she wants to proceed with the repair. Customer paid for the service fee. All water connections were dry at the time of service.

Near Manor, TX 78653

Wesley

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW4855HW0 Arrived on site and found unit operating with a dislodged suspension rod. Reinstalled rod. No new parts. Balanced unit. All checks good. Advised customer on use and care.

Near Woodway, TX 76712

Job Details: 12/31/2018

WASHER MAYTAG MVWC565FW1 Arrived to inspect washer making a loud banging noise. I tested the unit in diagnostic test mode. All components operated as designed All water lines were dry at the time of service.JOB COMPLETE

Near San Marcos, TX 78666

Robert

Job Details: 12/31/2018

MICROWAVE AMANA AMV2307PFS0 Arrived on job to replace control and bulb. After replacement test operation.

Near San Marcos, TX 78666

Diego G.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW5000DW1 Customer stated that another company has been out to work on washer. Cancel call

Near San Marcos, TX 78666

Diego G.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW5000DW1 Customer stated that another company has been out to work on washer. Cancel call

Near San Marcos, TX 78666

Diego G.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW5000DW1 Customer stated that another company has been out to work on washer. Cancel call

Near Austin, TX 78753

Leonardo

Job Details: 12/31/2018

RANGE KITCHENAID KSGB900ESS0 Arrived on site to test unit for f2e0 panel disconnected. Followed the direction on tech manual and erased all codes and no codes came back. Oven working correctly at this time.

Near Lampasas, TX 76550

Arthur B.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRB322DMBM00 Arrived onsite for customer complaint of ice maker on bottom refrigerator of making ice. Found icemaker stuck mid harvest. Removed and replaced icemaker. Reassembled. Icemaker call for water immediately. No other issues found. All water connections were dry at time of service.

Near Pflugerville, TX 78660

Wesley

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRS325SDHV00 Arrived on site and found Evap drain clogged. Declogged drain and removed ice. All checks good. Unit operating as designed.

Near Marble Falls, TX 78654

Thomas L.

Job Details: 12/31/2018

DISHWASHER WHIRLPOOL WDTA50SAHW0 Arrived on site for poor washability. Tested unit. Unit has a failed wash motor. Replaced motor and tested. Operations are normal and allow ater connections were dry.agoads@gmail.com

Near Austin, TX 78726

Paul

Job Details: 12/31/2018

DRYER MAYTAG MGDB880BW0 Arrived onsite for the dryer with the door not sealing. I found the door catch with a broken spring. I replaced the door catch and the door closes properly at this time. Call complete.

Near Kyle, TX 78640

Robert

Job Details: 12/31/2018

REFRIGERATOR MAYTAG MFI2570FEZ05 Arrived on job for complaints of filter stuck in housing. Try to remove filter but not turning. Replaced housing and customer had filter.

Near Dripping Springs, TX 78620

Brandon

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL GI0FSAXVY012 "Arrived on site for customer complaint of ice maker not producing ice, I found faulty/shorted control, I replaced control, unit tested good. 7723768034"

Near Leander, TX 78641

James

Job Details: 12/31/2018

OVEN FRIGIDAIRE FFGF3017LBH Arrived on site and customer stated that the control would reset if the oven is on and they attempted to use the cooktop. I verified the issue and found the reader right burner igniter is working intermittently. I installed new new main harness and found the issue with the rear right igniter is in the igniter harness. I tested operation and oven now works with cooktop and does not reset the control. Unit working properly. Job complete

Near Seguin, TX 78155

Diego G.

Job Details: 12/31/2018

WASHER MAYTAG MVWX655DW1 "Arrived on site. Check for no spinning issues. Found multiple problems found bad hub not allowing basket to spin. Wasn’t able to remove wash plate. Also found water valve bad not allowing cold water to come into unit.Will need wash plate, housing and hub to repair unit. Office to reschedule; ordrng 1 W10528947 (hub) and 1 W10902814 (IMPELLER ) and 1 W11127357 (HOUSING )"

Near Seguin, TX 78155

Diego G.

Job Details: 12/31/2018

Near Seguin, TX 78155

Diego G.

Job Details: 12/31/2018

Near Austin, TX 78723

Joseph C.

Job Details: 12/31/2018

MICROWAVE WHIRLPOOL WMH31017FB0 Arrived on site for “door open/close door error” complaint. Inspected unit and found switches and interlocks faulty. Removed and replaced door switches and interlocks. Tested unit. Unit is performing as designed.

Near Austin, TX 78750

Paul

Job Details: 12/31/2018

DISHWASHER KITCHENAID KDTE104ESS1 Arrived onsite for the dishwasher doing the same thing as before. I checked stored error codes and found an F7E1 & F5E1. The unit went thru the diagnostics cycle and completed it with all components working as designed. The heater was drawing 7.4 amps in the wash cycle. I explained to the customer how and when to check the unit for too many suds at the beginning of the wash cycle to see if this is the cause. The customer is going to check and if there is sudsing they will switch to a liquid detergent and only fill the dispenser cup half full. If there are no suds present and this happens again we will change the control. If the control needs to be replaced

Near Leander, TX 78641

James

Job Details: 12/31/2018

RANGE WHIRLPOOL WGG745S0FS02 Arrived on site and installed new burner head and cap. Tested for proper operation and found burner is still hard to ignite but has gotten slightly better. Called tech line and spoke to Mark #7723752277. Recommended to file the gas port opening to allow better gas flow to igniter for a more consistent ignition. Filed port and tested. Unit working properly. Job complete

Near Fort Hood, TX 76544

Arthur B.

Job Details: 12/31/2018

MICROWAVE WHIRLPOOL WMH32519FB0 Arrived onsite to customer complaint of OTR microwave not heating and making loud noises. Tested unit and found magnetron making the loud noises. Uninstalled microwave and removed wrapper. Removed and replaced capacitor and magnetron. Reassembled and reinstalled. Tested unit with 1 cup of water @ 2 mins. Water was boiling hot. No other issues found.

Near Austin, TX 78717

Lou

Job Details: 12/31/2018

COOKTOP WHIRLPOOL WCG51US6DS00 "arrived on site to inspect cooktop Ignitors arching. Upon further inspection, the customer advised that the back right burner began to arc without the unit being turned on. I removed the unit from the countertop and removed the cooktop to inspect the valves, harness/ignitors and orifice holders. I found that the spark module was bad and the back right burner Ignitor was broken. I removed and replaced the spark module and back right burner ignitor. I tested the unit and it operated as designed. I tested the valves and harness connection to the valves and all were operating properly. None of the valves were sticking and did not need replacing. Using my liquid gas leak detector, I checked all gas connections and all were good. No gas leaks detected during service, job completed."

Near Austin, TX 78739

Leonardo

Job Details: 12/31/2018

MICROWAVE GE JES2051SN1SS Arrived on site to to replace switch. Took unit out and opened unit up. Replaced switch test unit and unit test good. Unit heating correctly job complete

Near Burnet, TX 78611

Thomas L.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL KRSF505ESS00 "Arrived on site for no water dispensing and no ice production. Found that the filter housing is not letting water pass-through. The waterlines will not come free from the housing. I am ordering the water lines as well. I have no Internet connection or cell phone connection and will have the office return the call to the customer to reschedule.; ordrng 1 W10279882 (tube,filter inlet) and 1 W10279885 (tube,filter outlet)"

Near Killeen, TX 76549

Arthur B.

Job Details: 12/31/2018

RANGE WHIRLPOOL RF111PXSQ1 Arrived onsite to removed and replace LF Element to range from prior tech’s diagnosis. Removed and replaced LF element. Tested. Element heats up as intended. Infinite switch not needed.

Near Austin, TX 78729

Paul

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL ED5PVEXWS05 Arrived onsite for the refrigerator not cooling in either compartment. I had no fans or compressor running. I only had 14 volts from the red wire to ground at the compressor and .6 volts from red to white. I changed the defrost control and the evaporator motor started running but the condenser fan and compressor were not starting. I found 121 volts from red to ground but only 60 when checking to white. I found a broken neutral wire at the fill valve. I repaired the neutral wire and tested the unit. The unit is working as designed. There were no water leaks present at the time of service. Call complete.

Near Salado, TX 76571

Arthur B.

Job Details: 12/31/2018

OVEN WHIRLPOOL WEE745H0FS1 Arrived onsite for customer complaint of oven not heating properly. Preheated oven to 350F. Used temperature probe and found temperature @380F. Calibrated oven to +15F and preheated to 450F. Unit maintained temperature within +/-10F. No other issues found.

Near Austin, TX 78731

Cliff

Job Details: 12/31/2018

COOKTOP JENN-AIR JED8430ADB Arrived on site to diagnose a cooktop that is arcing when breaker is turned on. Found left front infinite switch shorted out causing failure. Replaced infinite switch and tested unit. Found all is functioning properly at this time.

Near Georgetown, TX 78626

Jonathan S

Job Details: 12/31/2018

MICROWAVE AMANA AMV2307PFS2 "Arrived on site for microwave not powering on. Performed diagnostics mode and tested 20 amp fuse and found good. Tested voltage outlet and found not getting 120 volts, found neutral opened. Connected microwave to different outlet and tested. All tested good on microwave. Customer needs to contact electrician."

Near Georgetown, TX 78628

Steve C.

Job Details: 12/31/2018

DRYER MAYTAG MEDB765FW0 Arrived on site for the unit clothes are coming out damp. Tested the unit and found the unit has proper airflow outside and proper temperature. Called Whirlpool Sr#7723753887 David And advised to increase the heat level to number 4. Unit is working properly and advise customer to clean air vents every six months.

Near Driftwood, TX 78619

Brandon

Job Details: 12/31/2018

DISHWASHER WHIRLPOOL KDTM354DSS5 "Arrived on site for customer complaint of unit not washing, found faulty wash motor. I replaced wash motor, unit tested good. Collected payment on cc; ordrng 1 CNOTE (SCODE)"

Near Pflugerville, TX 78660

Wesley

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRX988SIBM03 "Arrived on site and found frozen Evap drain line in fridge. Cleared and found no obstruction.

Near Round Rock, TX 78681

Cliff

Job Details: 12/31/2018

WASHER MAYTAG MAH3000AWW Arrived on site to replace motor and control for washing machine. Found after replacing motor control kit unit would run for a few seconds and shut down completely. This is due to a shorted main control board and timer assembly. Failure is due to normal wear and tear. Timer and main control both need to be replaced to complete repairs. Office will need to have authorization provided by home warranty and set return appointment.; ordrng 1 CNOTES (AUTHO NEEDED) and 1 WP22002441 (timer) and 1 WP22002988 (cntrl-elec)

Near Lago Vista, TX 78645

James

Job Details: 12/31/2018

COOKTOP WHIRLPOOL KFGS366VSS01 Arrived on site and found the center burner base has melted. Gained access to the burner box and found no evidence of a fire under the cooktop or spill over. Took photos of findings. The center burner base shows to be discontinued and no longer available. Job complete

Near Austin, TX 78748

Brandon

Job Details: 12/31/2018

WASHER MAYTAG MVWX655DW1 "Arrived on site for customer complaint of unit not spinning or draining, found out of balance error code in diagnostic mode, I calibrated load size in diagnostic mode and ran all tests. Unit tested good."

Near Kingsland, TX 78639

Thomas L.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRF535SWHZ00 Arrived on sight for Noisey operation. Cycled unit on and found that the units power cord was vibrating against the back condenser cover panel. Correct in that situation and unit is now quiet. no water is hooked up to this unit

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KFIS29PBMS00 Customer stated they unplug unit and kicked it back on.

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KFIS29PBMS00 Customer stated they unplug unit and kicked it back on.

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KFIS29PBMS00 Customer stated they unplug unit and kicked it back on.

Near Austin, TX 78703

Robert

Job Details: 12/31/2018

WASHER WHIRLPOOL WFW96HEAW0 Arrived on job to replace flow meter and control . After replacement of parts ran diagnostics and all operation normal. No leaks detected at time of service.

Near Hutto, TX 78634

Steve C.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRS325SDHZ01 Arrived on site to replace the UI. Found the good frost pattern on the evaporator and thermistor checks good. Replaced the UI and tested the unit. Unit works properly and all water connections were dry at the time of service.

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

ICE MACHINE KITCHENAID KUIC15NRTS0 "Arrived on site. Check for no ice issues. Found circulating pump bad not allowing water to go over evaporator. Replaced circulating pump. Cycled icemaker, all functions tested OK. Instructed customer to allow 24 to 36 hours for unit to fill up completely. No leaks present. Job complete"

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

Near New Braunfels, TX 78130

Diego G.

Job Details: 12/31/2018

Near Austin, TX 78745

Leonardo

Job Details: 12/31/2018

COOKTOP WHIRLPOOL WEE745H0FH0 Arrived on site to to replace cooktop. Opened cooktop box and customer inspected cooktop and no damaged found on new cooktop. Replaced cooktop test all burner all burners working at this time job complete

Near Austin, TX 78727

Paul

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KRFF507ESS01 Arrived onsite for the refrigerator to install the previous diagnosed parts. I finished defrosting the coil. I changed the motor and harness. I repositioned the thermistor and wrapped it with foil tape and secured it with a wire tie. I confirmed the evaporator cover tabs were broken off at the top. I sealed the evaporator housing at the top and installed the new cover attaching it with screws thru the tabs. I sealed a air gap at the drain tube in the rear. I tested the unit and found it working as designed. There were no water leaks present at the time of service. Call complete.

Near Austin, TX 78759

Scott

Job Details: 12/31/2018

COOKTOP KITCHENAID KGCD807XSS02 "Arrived on site for only right front burner working . Found switches are failing and failed . Ordering switches 2 right , 2 left . Return 1/2 . No gas leaks detected at time of service . ; ordrng 2 WP74010857 (switch- sp LEFT)s and 2 WP74010858 (switch- sp RIGHT )s"

Near Georgetown, TX 78626

Arthur B.

Job Details: 12/31/2018

MICROWAVE WHIRLPOOL WMH32519HZ3 "Arrived onsite for tenant complaint of OTR microwave not starting. When arrived, found cabinet where interlocks is mounted is all smashed in. Also found control panel not secured as well did to frame damage . Advised maintenance that unit this is considered non repairable. Snapped photos of damage, Called WPL Techline Dave SR#7723795589 and relayed findings. Whirlpool will be in contact within 3-5 business days."

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRB322DMBM00 Arrived on site. Replaced harness in control. All functions tested OK. Instructed customer to allow 24 hours for unit to cool down properly. No leaks present. Job complete

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

Near Georgetown, TX 78626

Steve C.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRT549SZDM01 Arrived on site for the unit door has a dent. Found the dent on the ff door top left corner. Replaced the ff door and tested the unit. Unit works properly and all water connections were dry at the time of service.

Near Austin, TX 78758

Paul

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW4616FW2 Arrived onsite for the washer to finish troubleshooting and possibly replace the previous diagnosed parts. I found the motor good and showing 6 ohms on both windings. I found the lower harness open. I replaced the lower harness and tested the unit. The unit is working as designed. Call complete.

Near Austin, TX 78732

Cliff

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KSSC42QVS02 "Arrived on site to diagnose a refrigerator that is not dispensing ice. Tested unit and found dispenser door not sealing properly and dispenser seal motor loose. This is causing air leak in unit. Air leak is causing frozen Condensation to find dispenser auger. Also noted button for ice bin release Missing. Dispenser motor, sealed, and button will all need to be replaced to complete repairs. No leaks were found at time of service. Return date is set for 12/26/18.; ordrng 1 WP2180353 (door-chute)"

Near Austin, TX 78758

Paul

Job Details: 12/31/2018

WASHER WHIRLPOOL WET4024HW0 Arrived onsite for the dryer. I repaired the harness using a insulated butt splice connector. I tested the unit and all is working as designed. Call complete.

Near Austin, TX 78726

Lou

Job Details: 12/31/2018

DISHWASHER KITCHENAID KDTM354DSS4 "arrived on site so previously diagnosed and ordered part. Due to no voltage coming from the control to the element, I removed and replaced the control and tested the unit. The unit operated as designed and the element heated as designed. No water leaks observed during service, job completed."

Near Del Valle, TX 78617

Joseph C.

Job Details: 12/31/2018

WASHER MAYTAG MVWC565FW1 "Arrived on site for “will not spin out clothes” complaint. Per my previous diagnosis, removed and replaced motor, actuator and capacitor. Tested and calibrated unit. Unit is performing as designed. No leaks detected, at time of service."

Near Seguin, TX 78155

Diego G.

Job Details: 12/31/2018

WASHER MAYTAG MVWB765FW0 Arrived on site. Check for agitation issues. Found sheet underneath agitator. Removed sheet and found agitator warped. Will need new agitator to repair unit. Rescheduled for 12/27/18 customer is requesting last call of the day if possible.; ordrng 1 CNOTES (CNOTES ) and 1 W11161960 (AGITATOR)

Near Seguin, TX 78155

Diego G.

Job Details: 12/31/2018

Near Seguin, TX 78155

Diego G.

Job Details: 12/31/2018

Near Austin, TX 78717

Lou

Job Details: 12/31/2018

DRYER AMANA NED4655EW1 "arrived on site to inspect dryer not heating. Upon further inspection, I checked the vent hose and found it pinched together and not allowing airflow to go through. Using my vent test, I tested the airflow and the unit failed. I reinstalled the vent hose and tested it again and it still failed. I advised the customer of my findings and advised that the vent tube going, out of the apartment would probably need to be cleaned. I opened the top panel and turned the unit on to heat and inspected the element and it was operating as designed. The unit was very hot inside the drum. No lint observed during service, job completed."

Near Austin, TX 78717

Lou

Job Details: 12/31/2018

WASHER AMANA NTW4516FW2 "arrived on site to inspect washer not spinning. Upon further inspection, I placed the unit in diagnostics and tested and error code for the door lock appeared. I cleared the code and continued with testing and the unit operated as designed with no error codes at the end of testing. I placed the unit in manual test mode and tested agitate and spin and it operated as designed. Using my multimeter, I tested the lid lock and it was good. I advised the customer of my findings. No water leaks observed during service, job completed."

Near Del Valle, TX 78617

Joseph C.

Job Details: 12/31/2018

WASHER MAYTAG MVWC360AW0 "Arrived on site for “leaking water from bottom and loud noises” complaint. Per my previous diagnosis, removed and replaced gearbox, actuator and drive pulley. Calibrated and tested unit. Unit is performing as designed. No leaks detected, at time of service."

Near Round Rock, TX 78681

Arthur B.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRX988SIBM01 "Arrived onsite for customer complaint of dual evaporator refrigerator not cooling properly in RC section. Found temperature is @41F. Found no air flow from RC rear tower. Upon removal of evaporator cover, found evaporator fan motor was installed incorrectly causing air flow going towards evaporator. Reinstalled evaporator in correct position and reassembled. Tested unit. Found good air flow coming from air tower. No other issues found. All water connections were dry at time of service."

Near New Braunfels, TX 78132

Robert

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KRMF706ESS01 Arrived on job for complaints of no ice. Ran diagnostics and couldn’t complete harvest. Replaced icemaker and rerun test. Harvest complete. No leaks detected at time of service.

Near Liberty Hill, TX 78642

James

Job Details: 12/31/2018

DISHWASHER WHIRLPOOL ADB1400AGS1 Arrived on site and tested operation. I found the dispenser leaking and not dispensing rinse aid. After removal I found the dispenser has a bad float in the rinse aid reservoir and the dispenser had to turn almost upside down to allow plunger to dispense selected amount. Installed new dispenser and tested. Unit working properly and no leaks found after repair. Job complete

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

REFRIGERATOR KITCHENAID KRMF706ESS01 Arrived on site. Check for no ice issues. Found water line going to ice maker frozen over. Thawed out line and verified water going into ice maker all checked OK. Found temperature at 33° in refrigerator. Adjusted to recommended setting to keep from freezing over. All functions tested OK. Instructed customer to allow 24 to 36 hours for ice bin to fill up all the way. No leaks present. Job complete

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

Near New Braunfels, TX 78132

Diego G.

Job Details: 12/31/2018

Near Liberty Hill, TX 78642

James

Job Details: 12/31/2018

MICROWAVE AMANA AMV2307PFS0 Arrived on site and found left edge of door cracking and coming apart. Installed new door and tested for proper fit and function. Door tests good. Job complete

Near Martindale, TX 78655

Diego G.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW4816FW2 "Arrived on site. Replaced water valve and cycled washer, all functions tested OK. Ran diagnostic test and calibrated unit. No leaks present. Job complete"

Near Martindale, TX 78655

Diego G.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW4816FW2 "Arrived on site. Replaced water valve and cycled washer, all functions tested OK. Ran diagnostic test and calibrated unit. No leaks present. Job complete"

Near Martindale, TX 78655

Diego G.

Job Details: 12/31/2018

WASHER WHIRLPOOL WTW4816FW2 "Arrived on site. Replaced water valve and cycled washer, all functions tested OK. Ran diagnostic test and calibrated unit. No leaks present. Job complete"

Near Georgetown, TX 78626

Steve C.

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRF736SDAM13 Arrived on site to replace the icemaker per previous technician. Replace the icemaker and tested the unit. The icemaker cycles and filled with water. All water connections were dry at the time of service.

Near Killeen, TX 76541

Job Details: 12/31/2018

RANGE FRIGIDAIRE FFGF3023LWE Arrived to install previously ordered parts. I removed and replaced the igniter assembly. I reassembled the unit and unit tested as designed.JOB COMPLETE

Near Leander, TX 78641

Lou

Job Details: 12/31/2018

DISHWASHER WHIRLPOOL WDF331PAHS0 "arrived on site to inspect dishwasher not working. Upon further inspection, I placed the unit in diagnostics and tested with no error codes. The unit operated as designed with no error codes showing at the end of testing. I tested the element by pouring water on it and it sizzled. I checked all of the connections underneath the unit and all were good. I notified the customer of my findings. They were not available to sign for the receipt. No water leaks observed during service, job completed."

Near Round Rock, TX 78681

Jonathan S

Job Details: 12/31/2018

REFRIGERATOR WHIRLPOOL WRX988SIBM01 "Arrived on site to install previous diagnosed parts. Removed torn gasket and installed new. Heated gasket with gun. Added silicone around drain tube. Removed broken escutcheon and installed new. Tested all operations. Found customer has filtration systematic does need filter in unit. All tested good, no water leaks present"