Near New Braunfels, TX 78132
Diego G.
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTM404ESS3
"Arrived on site. Check for no operation issues. Found motor locked up not allowing water to spray inside dishwasher. Replaced sump and motor assy and cycled, all functions tested OK. No leaks present. Job complete"
Near New Braunfels, TX 78132
Diego G.
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTM404ESS3
"Arrived on site. Check for no operation issues. Found motor locked up not allowing water to spray inside dishwasher. Replaced sump and motor assy and cycled, all functions tested OK. No leaks present. Job complete"
Near New Braunfels, TX 78132
Diego G.
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTM404ESS3
"Arrived on site. Check for no operation issues. Found motor locked up not allowing water to spray inside dishwasher. Replaced sump and motor assy and cycled, all functions tested OK. No leaks present. Job complete"
Near Temple, TX 76502
Arthur B.
Job Details:
12/21/2018
DISHWASHER GE GSD3230F00WW
Arrived onsite for customer complaint of spray arms on dishwasher not spinning or water entering unit. Tested unit and found water supply at house was turned off. Turned water on and retested. Water now enter and sprayarms now spins. No other issues found. All water connections were dry at time of service.
Near VLG O THE HLS, TX 78738
Cliff
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTE234GPS0
Arrived on site to diagnose a dishwasher that is not drying. Tested unit and found error codes were not reset after replacing pump on prior visit. This was causing heater not to run as F7 E1 error code was saved due to pump failure. Reset error codes and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Round Rock, TX 78681
Jerry C.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRX988SIBM01
WRX988SIBM01 Arrived to inspect water leak. I found the issue was with the unit not draining correctly and the ice maker housing not fully seated into the chassis. The right rc door gasket was torn and will require replacement. The ice maker facia was missing a mounting tab and will require replacement. The unit will require complete adjustment and sealing of the drain tube assembly. The customer will defrost the unit prior to our return. Office to contact the arrange return service and allow the customer time to defrost. No leaks observed during service. ; ordrng 1 W10846057 (gasket-fip) and 1 WPW10553630 (escutcheon)
Near Lakeway, TX 78738
Cliff
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTE104ESS0
Arrived on site to diagnose a dishwasher with a dispenser lid that is not operating properly. Found dispenser lid gasket rolled under and preventing lid movement. Reset gasket in the proper position and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.Svc/Lbr (129.99+tax)
Near Belton, TX 76513
Arthur B.
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL WDF520PADM7
Arrived onsite for builder complaint of dishwasher with loud noises per inspector notes. Tested unit and found noises are normal. This unit has a plastics and noises coming is normal and working as intended. No other issues found. All water connections were dry at time of service.
Near Temple, TX 76502
Arthur B.
Job Details:
12/21/2018
OVEN KITCHENAID KODE507ESS03
Arrived onsite to install to lower door assembly from prior visit’s diagnosis. Installed new lower door glass assembly and nameplate. Reinstalled door. Customer satisfied with new replacement. No other issues found.
Near New Braunfels, TX 78130
Diego G.
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL WDF520PADB7
"Arrived on site. Checked for no operation issues. Found loose connection at control not allowing unit to power up. Reconnected connector and cycle, all functions tested OK. No leaks present. Job complete"
Near New Braunfels, TX 78130
Diego G.
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL WDF520PADB7
"Arrived on site. Checked for no operation issues. Found loose connection at control not allowing unit to power up. Reconnected connector and cycle, all functions tested OK. No leaks present. Job complete"
Near New Braunfels, TX 78130
Diego G.
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL WDF520PADB7
"Arrived on site. Checked for no operation issues. Found loose connection at control not allowing unit to power up. Reconnected connector and cycle, all functions tested OK. No leaks present. Job complete"
Near Copperas Cove, TX 76522
Steve C.
Job Details:
12/21/2018
DRYER WHIRLPOOL WED9200SQ1
"Arrived on site for the unit turns on but nothing happens. Tested the unit and down one pressing start the unit will make a humming noise. Found the drama will not turn clockwise. Found the belt is also tearing. Found the unit will need a new motor, blower wheel, and the dryer repair kit.; ordrng 1 279787 (motor) and 1 4392067 (dryer repair kit) and 1 WP697772 (wheel)"
Near Temple, TX 76504
Arthur B.
Job Details:
12/21/2018
WASHER AMANA NTW4516FW3
Arrived onsite for customer complaint of top load washer not completing cycles. Ran diagnostics and found no error codes. Tested water valves and found water is barely coming into unit. Advised customer to have water house supply looked over by apartment maintenance. No other issues found. All water connections were dry at time of service.
Near Cedar Park, TX 78613
James
Job Details:
12/21/2018
DRYER WHIRLPOOL WED9200SQ0
arrived on site and tested operation. Found no heat from dryer. Tested element and fuses and found element has failed. Installed new element and cleaned lint from unit. Tested for proper operation and found unit working properly. Job complete
Near Georgetown, TX 78628
James
Job Details:
12/21/2018
REFRIGERATOR MAYTAG MSD2756GEB
"Arrived on site and tested operation. I found the ice maker has come loose from the wall and the auger motor housing has broken at the auger motor. Installed new housing and ice maker. Tested for proper operation and found unit working properly. Job complete"
Near Lampasas, TX 76550
Steve C.
Job Details:
12/21/2018
RANGE WHIRLPOOL WEEA25H0HN1
Arrived on site for the unit will not heat the oven. Customer advise there is a error code f1 e0. Tested the unit and found the unit will not heat. Replace the control board a test of the unit. Found the unit is still not heating. Found the unit does not have proper voltage. Advise customer to call a electrician.
Near Canyon Lake, TX 78133
Diego G.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRV986FDEM01
Arrived on site. Check for leaking issues. Found drain clogged again. Unclogged drain and vacuumed out foam pieces. All functions tested OK. No leaks present. Job complete
Near Canyon Lake, TX 78133
Diego G.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRV986FDEM01
Arrived on site. Check for leaking issues. Found drain clogged again. Unclogged drain and vacuumed out foam pieces. All functions tested OK. No leaks present. Job complete
Near Canyon Lake, TX 78133
Diego G.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRV986FDEM01
Arrived on site. Check for leaking issues. Found drain clogged again. Unclogged drain and vacuumed out foam pieces. All functions tested OK. No leaks present. Job complete
Near Leander, TX 78641
James
Job Details:
12/21/2018
VENTHOOD WHIRLPOOL UXT4230ADS
Arrived on site and tested operation. Found that the fan runs properly and light functions properly as well. Tested the holder for the filter and found it to be functioning properly and the filter can be removed and installed properly. Unit tests good. Job complete
Near Killeen, TX 76549
Al
Job Details:
12/21/2018
RANGE WHIRLPOOL RF111PXSQ1
"Arrived to inspect front left 8” burner not working. I verified the complaint, I removed the element from the receptacle and tested it with the multimeter . The element had NO continuity. I removed the rear and tested it and it had continuity. I ordered WP9761346 8” element 814399 receptacle and will return with the switches.; ordrng 1 814399 (RECEPTICAL ELEMENT) and 1 WP9761346 (ELEMENT 8” SURFACE)"
Near Austin, TX 78748
Luis
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRS315SDHM00
"Arrived on site for water issue. Tested water dispenser,water dispensing correctly. Temp of water extremely cold. Diagnosed water line freezing,adjusted temp in fresh food to recommended setting,flushed water lines to prevent water lines from freezing."
Near Lampasas, TX 76550
Steve C.
Job Details:
12/21/2018
REFRIGERATOR GE GSS25GMHKCES
Arrived on site for the unit is still freezing the reservoir and wont dispense water. Customer also advise the food is freezing in the fresh food compartment. Called ge and advise for the call GE 8003861215 and to give them the Incident #181217-001588. All water connections were dry at the time of service.
Near , TX 78648
Diego G.
Job Details:
12/21/2018
RANGE WHIRLPOOL WGE745C0FS01
Spoke with customer over the phone and she said that another company already ordered part for unit. Cancelled call.
Near , TX 78648
Diego G.
Job Details:
12/21/2018
RANGE WHIRLPOOL WGE745C0FS01
Spoke with customer over the phone and she said that another company already ordered part for unit. Cancelled call.
Near , TX 78648
Diego G.
Job Details:
12/21/2018
RANGE WHIRLPOOL WGE745C0FS01
Spoke with customer over the phone and she said that another company already ordered part for unit. Cancelled call.
Near Round Rock, TX 78664
Jonathan S
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRX735SDBM
"Arrived on site for refrigerator ice maker not making ice. Per diagnostics mode and cycled ice maker. Found ice getting stuck in fingers. Removed ice maker and found fingers defective causing ice to get stuck. Removed failed ice maker and installed new. Tested cycle and monitor. All tested good, no water leaks present."
Near Austin, TX 78731
Luis
Job Details:
12/21/2018
REFRIGERATOR KITCHENAID KBFS22EWMS9
Arrived on site for loud noise. Diagnosed gears in damper making loud noise diagnosed unit will need damper control damper . Installed damper control powered unit on damper opened and closed no odd noise unit working as designed. Didn’t get approval at time of visit customer is paying if warranty approves bill warranty and refund customer.
Near Elgin, TX 78621
Thomas L.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRF535SWHZ00
"Arrived on site for no ice condition. Found freezer temperature at 1°. Water pressure to unit is good. Cycle icemaker, heard water valve buzz, but valve let no water through. Waterline is not frozen. Valve is defective. Replaced valve. It leaks at the top fitting. Will now need to order filter head.; ordrng 1 W10861009 (head-filtr)"
Near Austin, TX 78756
Joseph C.
Job Details:
12/21/2018
DRYER WHIRLPOOL WHD5090GW0
Arrived on site for “F08 error code and not powering on at all” complaint. Inspected unit and found F01 error code. Performed all tech sheet tests. Found control faulty. Removed and replaced control. Unit checks good. Customer is still not satisfied with quality of drying level.
Near Pflugerville, TX 78660
Wesley
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL WDT780SAEM0
Arrived on site and found motor dead. Unit is now operating as designed. All checks good after replacing unit motor assembly.
Near , TX 78653
Wesley
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRT318FMDM02
Arrived on site and found ice had not been cleared out of fill tube. Cleared ice. Now unit is operating as designed.
Near Highland Haven, TX 78654
Thomas L.
Job Details:
12/21/2018
DRYER MAYTAG MEDX8STBW0
Per customer request/ clean dryer and checked house vent. Also replaced repair kit.
Near Austin, TX 78749
Leonardo
Job Details:
12/21/2018
RANGE AMANA AGR6303MFS0
Arrived on site to test unit for knobs melting. Found knobs melting due to heat from top when using big pods. Ordering new knobs. Got black knobs need stainless W11164105. Oven gasket test good reschedule for 12/26 ; ordrng 4 W11164105 (KNOBS STAINLESS)s
Near Dripping Springs, TX 78620
Luis
Job Details:
12/21/2018
REFRIGERATOR JENN-AIR JF42NXFXDW05
"Arrived on site for no ice. Opened door ran diagnostics on optics,optics failed diagnostics,removed left side light bulb optics appeared to pass then shut off. Diagnosed unit will optics. Need AUTHO ; ordrng 1 NEEDAUTHO and 1 W10757851 (OPTICS), states that autho needed"
Near Kyle, TX 78640
Brandon
Job Details:
12/21/2018
RANGE WHIRLPOOL WFG505M0BS3
"Arrived on site for part replacement, part was damaged in box, ordering panel. ; ordrng 1 W10482110 (panel-drwr)"
Near Austin, TX 78744
Kevin
Job Details:
12/21/2018
WASHER WHIRLPOOL WTW4816FW2
"Arrived on site and inspected washer and found no power showing on control board, after replacing control ran a calibration and a diagnostic cycle and it is now functioning properly. No for the repair is required at this time, no water leaks from connections at time of service, job complete."
Near Austin, TX 78745
Kevin
Job Details:
12/21/2018
WASHER WHIRLPOOL WET4027EW1
"Arrived on site and set washer to run and it will begin a spin cycle but no water is draining spoke with tech line and although They could not find a specific reason this is happening, they recommended replacing every part of the washer.7723720284 washer motor is also hot to the touch but as it cools down washer will be getting to spin again. All parts appear to be correctly in place, tech line believes that we have a bad gear case; ordrng 1 285753A (coupling,motor) and 1 3360629 (gear case) and 1 WP3363892 (pump-water) and 1 WP661600 (drive motor)"
Near Georgetown, TX 78633
James
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRF736SDAW11
Arrived on site and tested operation. Found unit is making ice but 4-5 loads of ice are going under bin due to a hole in the ice bin. Found freezer temp at 3 degrees and ice maker housing at 12. Ice maker has proper amount of water in it and ice cubes are the correct size. Unit will need new ice bin to correct issue. Installed new ice bin. Job complete
Near Leander, TX 78645
Jerry C.
Job Details:
12/21/2018
COOKTOP JENN-AIR JGCP548WP02
"JGCP548WP02 Arrived to instal pre-shipped part. I inspected the part and it had a ding in the top right side, about one inch back from the front face. The customer elected to not have it installed and they will be contacting the MFG directly. The center front and all three back burners required low flame height adjustment. No gas leaks detected during service."
Near Kempner, TX 76539
Al
Job Details:
12/21/2018
MICROWAVE MAYTAG MMV6190DS1
"Arrived to install previously ordered parts. I removed and replaced the control boards. I tested the unit and the unit continued to count for 2 seconds and then turned off. I will order the following:W10269460- switch, W10269458 switch, W10727360 switch, WPW10156813 interlock, WP8206419 interlock, W10847192 transformerI called TECHLINE & spoke with JOEL 7723724286. switch kit Check voltage at control brown to blue. CheckW11244490 if needed; ordrng 1 10269460 (SWITCH) and 1 W10269458 (SWITCH) and 1 W10727360 (SWITCH) and 1 W10847192 (TRANSFORMER) and 1 WP8206419 (INTERLOCK)"
Near Austin, TX 78739
Luis
Job Details:
12/21/2018
ICE MACHINE KITCHENAID KUIX505ESS1
"Arrived on site to replace defective parts. Installed new compressor,valve and condenser fan motor. Vacuumed system down unit kept vacuum recharged system to manufacture spec powered unit on ran diagnostics unit passed all diagnostics. Unit working as designed."
Near Cedar Park, TX 78613
Jerry C.
Job Details:
12/21/2018
WASHER WHIRLPOOL MVWB765FW1
"MVWB765FW1 Arrived to inspect noise. The unit had F2E1 and no other codes stored. I tested within manual test mode and could not recreate the noise the customer had recorded on a device in agitate, but a loud squeal developed during the spin portion. I removed the gear case and found the seals were in failure. I replaced the failed gear case and calibrated. I tested the unit and it operated as designed. No leaks observed during service."
Near Round Rock, TX 78681
Jerry C.
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL MDB7749AWM1
"MDB7749AWM1 Arrived to instal parts. I found the issue with the unit was that it was surging and intermittently failing. I removed the sump cover and found the OWI coated with debris and the intake was 90% blocked. I removed the debris from the intake and OWI and inspected the chopper. I reassembled the unit and tested after allowing a control reset. The unit performed as designed and displayed the correct indicators, showing the OWI reading correctly during service test mode. No leaks observed during service."
Near Austin, TX 78754
Joseph C.
Job Details:
12/21/2018
REFRIGERATOR GE PSS26MSWASS
"Arrived on site for “no cooling and no water” complaint. Per previous diagnosis, removed and replaced bypass, refer assy cover, and control. Unit checks good. No leaks detected, at time of service. Blew out debris, from water line. Water flowing fine, now."
Near Round Rock, TX 78665
Jonathan S
Job Details:
12/21/2018
WASHER KENMORE 110.229321
Arrived on site for washer just making humming noises after customer installed pressure switch. Tested unit and found noise coming from motor. Checked basket and found not turning causing motor to lock up. Was able to get basket to turn and tested. Drain water from unit in spin mode. Found dirt buildup between tub and basket. Will need to remove basket and clean tub. Found agitator bolt head broken and not to remove wash basket. Unit is on uneconomical to repair.
Near Austin, TX 78745
Leonardo
Job Details:
12/21/2018
RANGE JENN-AIR JGR8885RDP
Arrived on site to replaced control. Replaced board test unit and heated oven to 350. Unit heated to 350 and broiler working as well. Job complete no leaks present at this time.
Near Bastrop, TX 78602
Joseph C.
Job Details:
12/21/2018
WASHER MAYTAG MVWB855DC2
"Arrived on site for “no power/not coming on” complaint. Inspected unit and found console faulty. Removed and replaced console. Tested and calibrated unit. Unit is performing as designed. No leaks detected, at time of service."
Near Killeen, TX 76543
Al
Job Details:
12/21/2018
RANGE WHIRLPOOL WFC150M0EW3
Arrived to inspect FR burner not changing temperature. I confirmed the complaint. Removed and replaced the switch. Tested the unit and unit tested as designed.JOB COMPLETE.ADDRESS IS 1508 BENTTREE B
Near Round Rock, TX 78681
Lou
Job Details:
12/21/2018
WASHER WHIRLPOOL MVWX655DW1
"arrived on site to inspect washer agitator not agitating. Upon further inspection, I placed the unit in diagnostics and tested with error code F0E5 showing. I cleared the code and continued with testing. The unit dispensed water into the tub, but when it was trying to agitate, the washplate was not moving. Once the unit was done with diagnostics, I placed it manual test mode and tested low agitation and the unit did not agitate and was making a very loud grinding noise. I stopped the unit and got out of diagnostics. I unplugged the unit and removed the washplate and found the washplate spindle teeth stripped. I tilted the unit back and found the pulley cover covered in oil residue. I removed the cover and found the belt, pulled, splotch kit, capacitor, motor, and actuator covered in oil. I contacted the office and spoke to CS and explained the situation and he advised to SCODE the gearcase. I removed the gearcase, splotch, motor, capacitor, and actuator an
Near Spicewood, TX 78669
Cliff
Job Details:
12/21/2018
RANGE GE CT9050SH1SS
Arrived on site to replace fan motor for oven. Replaced part and tested unit. Found all is working properly at this time.
Near Pflugerville, TX 78660
Jonathan S
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRS315SDHZ00
"Arrived on site for refrigerator door uneven and ice maker intermittent failure. Inspected ice maker and found bell arm not attached to ice maker, inspected ice maker and installed bell arm. After installing bell arm ice maker starting cycling without forced cycling. Also adjusted leveling wheels. All tested good and no water leaks present."
Near Georgetown, TX 78628
Jonathan S
Job Details:
12/21/2018
REFRIGERATOR KITCHENAID KRFF507ESS00
"Arrived on site for refrigerator not producing ice. Performed diagnostics mode and found ice maker getting caught on fingers. Removed ice maker and installed new. Cycled ice maker and monitor cycle. Tested all operation, all tested good at time of service. No water leaks present."
Near Round Rock, TX 78665
Tyler B.
Job Details:
12/21/2018
OVEN WHIRLPOOL WOS51EC0HS00
"Arrived on site for clock slowing down, found all connections good and tight, and found proper voltage coming in. Unit will need new panel and controls to complete repair ; ordrng 1 W11261167 (CONTROL) and 1 W11293216 (CONTROL)"
Near Kyle, TX 78640
Kevin
Job Details:
12/21/2018
WASHER MAYTAG MHWE201YW00
"Arrived on site and inspected washer and found bellow as a whole and is leaking. Replaced Bellow and leak has been corrected. No water leaks from connections at time of service, job complete"
Near Georgetown, TX 78628
Jonathan S
Job Details:
12/21/2018
REFRIGERATOR MAYTAG MFI2569VEM4
Arrived on site for refrigerator not cooling. Performed diagnostics and found display on UI going in and out. Tested voltage at UI and found present. Tested main control and found relay sticking. Will need to return with UI and main control. Office to schedule appointment when ETA is available on parts.; ordrng 1 12939601 (cntrl-elec/UI) and 1 WPW10312695 (CONTROL)
Near Pflugerville, TX 78660
Jonathan S
Job Details:
12/21/2018
DRYER WHIRLPOOL WED5000DW2
Arrived on site to install previous diagnosed part. Removed failed timer and installed new. Tested unit and checked for timer advancing. Checked heating operation. All tested good.
Near Georgetown, TX 78633
Jerry C.
Job Details:
12/21/2018
RANGE WHIRLPOOL WFG540H0ES0
WFG540H0ES0 Arrived to inspect flame issue. I found the front two large burners were incorrectly adjusted and flame height at low was too high. I adjusted and tested. The customer attempted Aqua clean several times and the unit would not boil out any of the water. A temperature offset was set to +20 and may be causing issues with self clean. The right rear stem was bent to the left and will require replacement. No gas leaks detected. ; ordrng 1 CNOTES (AM IF POSSIBLE PLEASE ) and 1 W10732139 (holder-orf) and 1 W10833885 (sensor) and 1 WPW10247744 (valve-brnr)
Near Georgetown, TX 78633
Jonathan S
Job Details:
12/21/2018
MICROWAVE WHIRLPOOL WOC54EC0AS04
"Arrived on site for microwave not heating as it did before and oven not maintaining correct temperature. Inspected unit and found liner damaged from foil being place on it. Performed diagnostics mode and found error code F1-E0, reset unit by powering off and on. Cleared fault code and failure did not reappear. Performed temperature test on bake mode at 350°, found average temperature at 352°. Tested microwave with 8 ounce of water at 66° ran at 100% for 63 seconds and found at 134°. All tested good."
Near Austin, TX 78758
Cliff
Job Details:
12/21/2018
DRYER WHIRLPOOL LEB6200PQ0
Arrived on site to diagnose a dryer that will not start. Tested unit and found door switch broken and shorted out. Failure is caused by normal wear and tear. Replaced door switch and tested unit. Found all is functioning properly at this time.
Near Belton, TX 76513
Arthur B.
Job Details:
12/21/2018
ICE MACHINE KITCHENAID KUIX505ESS2
"Arrived onsite for customer complaint of ice machine makes “POP” sound after draining. Observed ice machine making ice. Confirmed “POP” sound. Found when ice is harvested, a pop sound is heard. That sound is the hot gas valve sending heat to to evaporator to break ice off the plate. Advised customer of the findings. Also noise will sound louder due to the acoustics of the area. Unit works as intended. All water connections were dry at time of service."
Near New Braunfels, TX 78130
Robert
Job Details:
12/21/2018
WASHER AMANA NTW4516FW2
Arrived on job for complaints of not completing cycle. Ran diagnostics and control wouldn’t allow me to complete diagnostics selection. Replaced control and re try operation normal and ran calibration.
Near Dripping Springs, TX 78620
Brandon
Job Details:
12/21/2018
MICROWAVE WHIRLPOOL MH2175XSS4
"Arrived on site for customer complaint of microwave not working and giving open door error code. I replaced top and bottom interlocks as well as all 3 door switches as instructed by manufacturer, unit tested good.
Near Austin, TX 78723
Joseph C.
Job Details:
12/21/2018
WASHER WHIRLPOOL CAE2745FQ0
"Arrived on site for “intermittent no power/controls unresponsive” complaint. Inspected unit and found board not responding to diagnostic inputs. Would run through normal cycle, however. Removed and replaced board. Tested unit. Unit is performing as designed. No leaks detected, at time of service."
Near Round Rock, TX 78665
Tyler B.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRS588FIHW00
"Arrived on site for damaged door ,hinge and feet and door switch replacement. Replaced all listed. Took pics of door, leveled unit and door and tests good. No leaks on site"
Near San Marcos, TX 78666
Robert
Job Details:
12/21/2018
DISHWASHER WHIRLPOOL WDT720PADM0
Arrived on job for complaints of not draining. Found drain pump stopped with food. Instructed customer on use and care collected service fee
Near New Braunfels, TX 78130
Robert
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRF989SDAE00
Arrived on job for complaints of ice in refrigerator. Found evaporator cover covered in ice will need to defrost before repairs. ; schdld next appmnt for 12/21 FRI !
Near Lago Vista, TX 78645
Jerry C.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRF736SDAM12
WRF736SDAM12 Arrived to inspect no cool. I found the fc evaporator idled with a light frost and completely blocking above the fan. I removed the frost and the fan worked as designed. The unit could not be tested for defrost due to high fc temps (30.4) but appeared that the defrost was working and there was no frost at the intake area. I advised the customer to leave the unit off and the doors ajar for at least 24 hours prior to restarting. No leaks observed during service.
Near New Braunfels, TX 78130
Robert
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRF555SDFZ08
Arrived on job for complaints of no ice. Checked plug in icemaker compartments and found not connected. Corrected wires and test icemaker. Completed harvest and filled with water. No leaks detected at time of service.
Near Austin, TX 78751
Scott
Job Details:
12/21/2018
OVEN AMANA AGR6603SFB2
Arrived on site for door not closing properly . Replaced both hinges . Door is now closing normally . No gas leaks detected at time of service . Job complete.
Near Austin, TX 78749
Brandon
Job Details:
12/21/2018
DRYER MAYTAG MGDB765FW0
"Arrived on site for customer complaint of unit not starting. I instructed customer on how to use this type of control panel, not to press to hard and to hold start for 3 seconds. Unit tested good."
Near Austin, TX 78745
Kevin
Job Details:
12/21/2018
WASHER WHIRLPOOL WTW4955HW0
"Arrived on site and found power to control board is correct control board is not functioning. After replacing the control ran a calibration cycle in the washer is operating properly, no water leaks from connections at time of service, job complete"
Near Georgetown, TX 78633
Lou
Job Details:
12/21/2018
WASHER UNKNOWN WFW9250WW00
"arrived on site to inspect washer error code FL. Upon further inspection, I placed the unit in diagnostics and tested and it showed error code FL. I cleared the code and continued with testing. The unit operated as designed with no error codes at the end of testing. I followed the testing procedures in Service Matters for the error code FL. I checked the hoses, water pressure from the home, drain pump, inlet valve connectors, and pressure switch. When I checked the pressure switch at the PR6 connector, I found that at pins 21-22 there was no continuity. I removed and replaced the water level sensor switch and tested the unit and it operated as designed. I verified continuity to the PR6 connector pins 21-22. No water leaks observed during service, job completed."
Near Georgetown, TX 78633
Jonathan S
Job Details:
12/21/2018
RANGE WHIRLPOOL KGCU462VSS02
Arrived on site for cooktop right front burner not lighting. Performed diagnostics mode and found spark igniter grounded to frame. Adjusted igniter and tested. All tested good.
Near Kingsland, TX 78639
Thomas L.
Job Details:
12/21/2018
MICROWAVE GE JVM6175EF1ES
Arrived on site for unit operating on its own. Replaced control that had a stuck relay. Unit also has a closed thermostat that is causing cooling fan to run continuously. ; ordrng 1 WB27X709 (thermostat switch)
Near Austin, TX 78745
Leonardo
Job Details:
12/21/2018
RANGE WHIRLPOOL WEG515S0FS0
Arrived on site to test unit for damaged panel. Found scratched panel will need to order new panel control W10893960. Office to reschedule. ; ordrng 1 W10893960 (PANEL CONTROL STAINLESS )
Near Austin, TX 78741
Kevin
Job Details:
12/21/2018
WASHER WHIRLPOOL WFW72HEDW0
"Arrived on site and replaced handle and dispenser drawer diagnosed on previous visit, found that this made no change to amount of effort needed to open dispenser drawer, washer is operating normally. No water leaks from connections at time of service, job complete"
Near Buda, TX 78610
Brandon
Job Details:
12/21/2018
WASHER WHIRLPOOL WTW5000DW2
"Arrived on site for customer complaint of low water levels, I put unit into diagnostic mode and calibrated control and sensors. I then ran automatic test cycle, unit passed and tested good. I informed customer of washing expectations, and load levels."
Near Austin, TX 78738
Cliff
Job Details:
12/21/2018
DISHWASHER KITCHENAID KUDI02IRBS1
Arrived on site to diagnose a dishwasher that is not responding to controls. Tested unit and found unit in the child lock mode. Reset child lock as a courtesy for homeowner and found all is now functioning properly. No repairs were needed at this time. No leaks were found at time of service.
Near Kyle, TX 78640
Kevin
Job Details:
12/21/2018
WASHER WHIRLPOOL WFW8540FW1
"Arrived on site and found error code for water level system error, also found drain pump catch is clear. Pressure hose has no visible damage and ensured it was clear. Reset connections on pressure switch and washer will now complete a diagnostic cycle. No water leaks from connections at time of service, job complete."
Near Austin, TX 78745
Leonardo
Job Details:
12/21/2018
DISHWASHER MAYTAG MDB8959SFZ4
Arrived on site to test unit for broken tracks. Replaced both upper tracks test unit and unit test good job complete
Near Dripping Springs, TX 78620
Brandon
Job Details:
12/21/2018
COOKTOP WHIRLPOOL WCE97US0HS00
"Arrived on site to replace cooktop and UIB, I replaced both parts, unit tested good."
Near Leander, TX 78641
James
Job Details:
12/21/2018
REFRIGERATOR KITCHENAID KRMF706ESS00
Arrived on site and tested operation. Customer stated that the freezer section was warming up and making a loud humming noise. I found that the evap cover had evidence of an air leak. Found the upper left plastic rail has broken and would need to be replaced. Customer would prefer to hold off on replacement of bracket at this time. Job complete
Near Austin, TX 78738
Luis
Job Details:
12/21/2018
REFRIGERATOR KITCHENAID KFIS29BBMS02
"Arrived on site for cooling issue. Unit makes ice,ice melts and food thawing. Checked temp reading at 30 in freezer checked evaporator not a full frost patter. Called tech support,per tech support leak in system and recommend installing a dye drier. Ordering compressor,fresh food evaporator and a uv drier. Repair covered under manufacture system system warranty. File #7723709050; ordrng 1 2HOURREPAIR and 1 TJ90SF8404 (ACCESS VALVE ) and 1 W10276644 (COMPRESSOR) and 1 W11116006 (EVAPORATOR ) and 1 WPW10143759 (DRIER UV)"
Near Paleface Ranch, TX 78669
Cliff
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTE104ESS4
Arrived on site to replace pump assembly for dishwasher. Replaced pump and tested unit. Found all is functioning properly at this time. No leaks were found after services were performed.
Near Hutto, TX 78634
Wesley
Job Details:
12/21/2018
WASHER MAYTAG MVWB765FW2
Arrived on site and found slow leak from crack in male side of valve. Replaced housing. Unit is now operating leak free. All checks good.
Near Killeen, TX 76549
Steve C.
Job Details:
12/21/2018
REFRIGERATOR MAYTAG MSD2756GEB
Arrived on site for the unit is not cooling or freezing properly. Found all the fans are working properly. Manually activated the defrost control and unit will not go into defrost. Found the defrost control is shorted and will need to be replaced. The control is discontinued and office will need to contact AHS.; ordrng 1 12002104 (defrost asy) and 1 CNOTE (DISCONTINUED )
Near Leander, TX 78641
James
Job Details:
12/21/2018
WASHER WHIRLPOOL WTW8040DW4
Arrived on site and tested unit for not starting cycle. Ran diagnostics and found fault for lid not opened between cycles. Cleared fault and tested all functions in diagnostics under test 51. Found all functions test good and asked customer if it were a specific cycle that the issue occurred and there was not. Instructed customer on operation of unit and that the sounds heard are normal sounds. Unit working properly. Job complete
Near Austin, TX 78759
Scott
Job Details:
12/21/2018
WASHER MAYTAG MVWB765FW2
Arrived on site for leaking . Found valve leaking. Replaced valve . Ran diagnostics all checked good . No water leaks detected at time of service . Job complete.
Near Belton, TX 76513
Arthur B.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRX988SIBM03
Arrived onsite to install new LED module to RF section. Removed LED module and installed new replacement. Reassembled. Light came on. All other lights on as intended. No other issues found. All water connections were dry at time of service.
Near Austin, TX 78730
Cliff
Job Details:
12/21/2018
WARMING DRAWER KITCHENAID KEWS145SSS04
Arrived on site to diagnose a warming drawer that will not turn on. Tested unit and found knob broken. Replaced knob and tested unit. Found all is functioning properly at this time.
Near San Marcos, TX 78666
Robert
Job Details:
12/21/2018
DRYER MAYTAG MED3500FW1
"Arrived on job for complaints of not heating. Test fuse,hearer,thermostat and motor all good relay on control would click on and off too soon. Replaced control and test. If symptoms come back order motor."
Near Austin, TX 78725
Joseph C.
Job Details:
12/21/2018
REFRIGERATOR AMANA ASI2575FRS00
"Arrived on site for “noisy operation” complaint. Inspected unit and found condenser rattling against frame. Insulated bottom, between frame and condenser. Noise has abated. No leaks detected, at time of service."
Near Georgetown, TX 78633
Lou
Job Details:
12/21/2018
RANGE WHIRLPOOL WFG550S0HZ0
"arrived on site to inspect range oven temps. Upon further inspection, I removed the bottom panel to inspect the burner and Ignitor and I turned the unit on. I found the bake igniter spark was too far from the burner causing the spark to go back towards the ignter and not light the burner. I removed the igniter and remounted it in the proper position and tightened the mounting screws to properly ground it. I also crimped the terminal connector to the igniter. Tested the unit after adjustments and the burner is lighting immediately and the igniter is now sparking properly. I put the bottom panel back on and using my multimeter, I placed my thermal lead in the middle of the center rack and tested the unit on Bake at 350 degrees. At the 350 preheat, my temp reading was 395. My next five temp readings were 358, 363, 352, 348, 365 for an average temp reading of 357 degrees. I advised the customer of my findings and advised that the unit is operating as designed.
Near Round Mountain, TX 78663
Jerry C.
Job Details:
12/21/2018
WASHER GE GUD27ESSJ1WW
GUD27ESSJ1WW Arrived to inspect no agitation. I found the belt had failed and will require replacement. Further inspection revealed the gear case may have been leaking oil and caused the failure and should be ordered as well. Office to order belt and gear case and motor to be reverse flowed. Please allow two hours for service. No leaks observed during service. ; ordrng 1 CNOTES (2 HOURS SERVICE) and 1 CNOTES (PARTS AUTHORIZATION ) and 1 WH01X20436 (drive 3l) and 1 WH16X22784 (supports assembly) and 1 WH38X10018 (transmission pulley)
Near Cedar Park, TX 78613
James
Job Details:
12/21/2018
WASHER WHIRLPOOL WTW5800BW0
Arrived on site and installed new suspension. Ran calibration mode and auto diagnostics. Unit tests good. Job complete
Near Austin, TX 78732
Cliff
Job Details:
12/21/2018
DISHWASHER KITCHENAID KDTM354DSS0
"Arrived on site to install rack wheels and pivot clip for a dishwasher. Per homeowners request, as she was not home, I dropped the parts off at front door. Homeowner will install parts herself as she is familiar with how to do so."
Near Temple, TX 76502
Steve C.
Job Details:
12/21/2018
REFRIGERATOR WHIRLPOOL WRS315SDHB01
"Arrived on site for the unit is not freezing or cooling. Gain access to the evaporator and found there is only frost on the bottom section of the evaporator. Also found small oil leak from the compressor. Unit will need a new compressor, evaporator, uv drier and access valve. Will need three hours to complete the repair. Office will need to reschedule customer.; ordrng 1 CNOTE (3 HRS) and 1 TJ90SF8404 (ACCESS VALVE) and 1 W10507884 (compressor) and 1 WP2188823 (evaporator)"
Near Harker Heights, TX 76548
Al
Job Details:
12/21/2018
WASHER WHIRLPOOL WTW5000DW1
Arrived to inspect washer still not spinning water out of closets. I tested the motor at the windings and got 4.3 4/2 and 4.4 4/3I checked the J2 connections at the board and got no reading. I removed and replaced the harness and service tested the unit and unit tested as designed. I also Calibrated the washer. All water lines were dry at the time of service.Labor was deducted from previous calls for this unit.CS approved cost and parts charges. Spoke to Tech line MARK SR#7723707240 Diagnosis was a wiring issue needs harness