Near Bastrop, TX 78602
Nathaniel B.
Job Details: 04/10/2018
Model WTW8500DC3, Arrived on call for no beep from control panel when selecting keys, found that with the end beep key is not adjusting from off to low, medium, and high, and unit did have a f2 e1 error for stuck key, will need to order ui control panel, skyped office parts and talked to jordan and offive will reschedule with customer. No water leaks at time of call.
Near Georgetown, TX 78628
Thomas L.
Job Details: 04/10/2018
Arrived on site for improper operation. Unit cannot be pulled down off of the wall due to tile work. Customer is going to use the unit as it is until it breaks.
Near Bee Cave, TX 78738
Brandon
Job Details: 04/10/2018
Arrived on site for washer making grinding noise, found oil on floor under washer, found bad gearcase. I quoted customer for replacement of gearcase, customer denied repair, he will buy a new unit. Collected 108.24 on check.
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 04/10/2018
Model WRF993FIFM00, Arrived on call for freezer icemaker mold senser showes open, replaced freezer icemaker and went back in diag. And checked freezer mold senser for icemaker and is know reading senser all checks good, call complete.
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 04/10/2018
Model WRF993FIFM00, Arrived on call for freezer icemaker mold senser showes open, replaced freezer icemaker and went back in diag. And checked freezer mold senser for icemaker and is know reading senser all checks good, call complete.
Near Austin, TX 78730
Robert
Job Details: 04/10/2018
Near Austin, TX 78746
Scott
Job Details: 04/10/2018
Near Austin, TX 78701
Luis
Job Details: 04/10/2018
Refrigerator-replaced icemaker
Near Austin, TX 78738
Brandon
Job Details: 04/10/2018
Arrived on site for part hanger, Replaced wire harness main, and appliance manager for 18" oven. Unit tested good.
Near Austin, TX 78738
Daniel A.
Job Details: 04/10/2018
JDRP548WP02 Wire harness on appliance manager shorted/. Replaced wire harness/appliance manager normal operation after service .
Near Waco, TX 76710
Mike G.
Job Details: 04/10/2018
WRS325FDAW04, Arrived on site to install new icemaker checked unit after repair and icemaker is working properly and calling for water checked unit for water leaks and no leaks found at time of srv.. unit checked fine at this time...
Near Waco, TX 76710
Mike G.
Job Details: 04/10/2018
WRS325FDAW04, Arrived on site to install new icemaker checked unit after repair and icemaker is working properly and calling for water checked unit for water leaks and no leaks found at time of srv.. unit checked fine at this time...
Near Austin, TX 78727
Jerry C.
Job Details: 04/10/2018
KFIV29PCMS03 Arrived to inspect no cool. I found the compressor making noise above expected levels. The condenser was room temperature and the compressor was extremely hot. The sealed system will require replacement. Office to order compressor, dye drier, service port and evaporator. Office to schedule return service and allow 2 hours for sealed system work. No leaks observed during service.
Near Leander, TX 78641
Lou
Job Details: 04/10/2018
WDT920SADM0 arrived on site for broken track in dishwasher. Upon further inspection, I found that the actual RH track was missing. I quoted the customer $64.87 for the RH track and DW310 $179.99 for service fee and replacement...total $265.06. Customer agreed to repair and I installed a new RH track. Tested unit and unit tested good. No water leaks observed during service.
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 04/10/2018
Model MFI2269VEM10, Arrived on call for unit not cooling at all on both compartments, found compressor pulling 10 amps and then kicking off, used a test relay from truck and then found is pulling 1.1 amos and compressor is staying running and temp is pulling down, relay 72.65, svc/labor 199.99 which =272.64 plus tax 22.49 which =295.13, customer agreed to est, collected full balance of 295.13, installed start device from truck stock and is pulling 1.1 amps which is good and is pulling down to temp, no water leaks at time of call, call complete.
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 04/10/2018
Model MFI2269VEM10, Arrived on call for unit not cooling at all on both compartments, found compressor pulling 10 amps and then kicking off, used a test relay from truck and then found is pulling 1.1 amos and compressor is staying running and temp is pulling down, relay 72.65, svc/labor 199.99 which =272.64 plus tax 22.49 which =295.13, customer agreed to est, collected full balance of 295.13, installed start device from truck stock and is pulling 1.1 amps which is good and is pulling down to temp, no water leaks at time of call, call complete.
Near Liberty Hill, TX 78642
Thomas L.
Job Details: 04/10/2018
Arrived on site for E2F2 on display and no operation. Opened door and reseated control panel harness at control board. Unit now operates without code. Checked all operations. All water connections were dry. Mrs at home speaks very little English I informed Mr via phone of repairs and costs.
Near Georgetown, TX 78628
Jonathan S
Job Details: 04/10/2018
Whirlpool refrigerator model# WRF535SMBM. Not cooling. Compressor keeps kicking on and off.
Near Austin, TX 78746
Luis
Job Details: 04/10/2018
Ice machine. Replaced pump and bin thermistor
Near Georgetown, TX 78633
Thomas L.
Job Details: 04/10/2018
Arrived on site for no water dispensing through the door. Found the door switch is working as well as water valve. There is no water out of dispenser to door, water tank is frozen. Customer will try warm towels to thaw. I’d that doesn’t work customer will need to turn unit off unit it thaws.
Near , TX 76630
Mike G.
Job Details: 04/10/2018
MVWB835DW0, Arrived on site to install new water valve checked unit after repair and unit is now getting hot and cold water checked unit for water leaks and found that the hot water hose is leaking and talked to customer and customer is aware of hose leaking and told me that he is going to replace hoses today no other leaks found at time of srv... unit checked fine at this time....
Near , TX 76630
Mike G.
Job Details: 04/10/2018
MVWB835DW0, Arrived on site to install new water valve checked unit after repair and unit is now getting hot and cold water checked unit for water leaks and found that the hot water hose is leaking and talked to customer and customer is aware of hose leaking and told me that he is going to replace hoses today no other leaks found at time of srv... unit checked fine at this time....
Near Georgetown, TX 78628
Lou
Job Details: 04/09/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the dryer door. Tested unit and unit tested good. No lent observed during service.
Near Georgetown, TX 78628
Lou
Job Details: 04/09/2018
arrived on site to inspect noisy refrigerator. Upon further inspection, I found that the condenser was vibrating against the frame of the unit causing the noise. I used manufacturer provided mastic to eliminate the vibration/noise. No leaks observed during service.
Near Round Rock, TX 78681
Nathaniel B.
Job Details: 04/09/2018
Model WDT920SADM2, Arrived on call for water leaking from under dishwasher, found that customer is over soaping the machine customer is on a water softner and customer is useing soap packs which are way to much soap, customer to go to liquid soap and start with a table spoon of liquid and if still sudsing reduce to teaspoon of liquid and rinse aid set it to 1 and to run hot water at sink before starting dishwasher, also customer said they were out of town and when came home the bottom inner tub was full of water, will order water valve, turned off hot water to dishwasher under sink before leaving home, skyped office parts and no answer, office will reschedule with customer.
Near Round Rock, TX 78681
Nathaniel B.
Job Details: 04/09/2018
Model WDT920SADM2, Arrived on call for water leaking from under dishwasher, found that customer is over soaping the machine customer is on a water softner and customer is useing soap packs which are way to much soap, customer to go to liquid soap and start with a table spoon of liquid and if still sudsing reduce to teaspoon of liquid and rinse aid set it to 1 and to run hot water at sink before starting dishwasher, also customer said they were out of town and when came home the bottom inner tub was full of water, will order water valve, turned off hot water to dishwasher under sink before leaving home, skyped office parts and no answer, office will reschedule with customer.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 04/09/2018
Arrived on site or water leaking. Tested unit. Found stuck upper wash arm and oversudsing condition. Instructed customer to run cleaner through unit. I found no leaks but suspect oversudsing is causing issue. Water connections all dry at this time.
Near Hutto, TX 78634
Jonathan S
Job Details: 04/09/2018
Whirlpool refrigerator model# KRFC704FPS00 Arrived on site to install previous diagnosed parts. Gain
Near Georgetown, TX 78633
Cliff
Job Details: 04/09/2018
Kitchenaid oven KEMS309BSS00. Arrived on site to diagnose a oven with broken door glass. Found inner glass liner broken. Replaced glass liner and tested unit. Found all is functioning properly at this time.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 04/09/2018
Arrived quickly site for irractic operations. Found F2E1 failure code in diagnostics however unit is working properly at this time. It may be that the customer is holding down button for too long. Melissa relayed info to customer via phone. Water connections were dry. F2E1
Near Austin, TX 78729
Lou
Job Details: 04/09/2018
WFW70HEBW1 arrived on site for washer not spinning and making loud noise when supposed to. Upon further inspection, I placed the unit in diagnostic mode. When unit would agitate it would make a loud moaning noise. At the end of diagnostic, unit would make load moaning noise again and would not open; however, the unit did not show any error codes. Office to order rotor, stator, mounting screw, and control and schedule return service. No water leaks observed during service. Also
Near Temple, TX 76501
Dona
Job Details: 04/09/2018
Arrived on site for broken agitator, found barrel snapped off of washplate, replaced full assy. Verified unit is locking. This design does not look through sensing and wash per guide. All water connections dry, agitation, drain and spin checked good.
Near Kyle, TX 78640
Connor M.
Job Details: 04/09/2018
MAV551EEWW maytag washer Installed belt and tested unit. Unit working properly, no leaks detected.
Near Kyle, TX 78640
Connor M.
Job Details: 04/09/2018
WFW75HEFW0 whirlpool washer Arrived on site to test unit for not completeing cycle leaving clothes wet. Found no stored error codes, and unit passed diagnostic cycle. After discussing wash habnits with customer we determined the failures were due to an off balance load caused by load too small or bath mats. Unit working properly at time of service. Collected service via cc.
Near Austin, TX 78759
Cliff
Job Details: 04/09/2018
Kitchenaid dishwasher KUDS011JBS0. Arrived on site to diagnose a dishwasher that is not responding to controls. Found child lock activated when I arrived at home. Disabled child lock function and tested unit. Found all is working properly at this time and no failures found to unit. Advised homeowner on enabling and disabling the child lock function. No leaks were found at time of service.
Near Kingsland, TX 78639
Thomas L.
Job Details: 04/09/2018
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 04/09/2018
Model WRF757SDEM00, Arrived on call for fridge and freezer not keeping temp, found freezer temp at 0 degrees and fresh food at 48 degrees, found fresh food evap coil iced over and blocking fresh food evap fan from running, installed new fresh food senser due to corosion effecting reading of senser and also sealed around drain tube in rear and placed evap senser in fresh food in correct position on fresh food evap coil, customer to allow for 24-48 hours for fresh food to go to normal temps, all checked good in diag., no water leaks at time of call, call complete.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 04/09/2018
Model WRF757SDEM00, Arrived on call for fridge and freezer not keeping temp, found freezer temp at 0 degrees and fresh food at 48 degrees, found fresh food evap coil iced over and blocking fresh food evap fan from running, installed new fresh food senser due to corosion effecting reading of senser and also sealed around drain tube in rear and placed evap senser in fresh food in correct position on fresh food evap coil, customer to allow for 24-48 hours for fresh food to go to normal temps, all checked good in diag., no water leaks at time of call, call complete.
Near Buda, TX 78610
Connor M.
Job Details: 04/09/2018
MEDC215EW1 maytag dryer Arrived on site to test unit for not heating. Found element open. Also found excessive lint build up in dryer. Removed excess lint and insturct on having ducts cleaned before continuing use. Unit working properly. Made aware of potential fire hazard if unit is used and issue with venting isnt rectified.
Near Killeen, TX 76542
Mike G.
Job Details: 04/09/2018
NTW4516FW1, Arrived on site for unit will fill but not start washing, checked unit and found that the the unit is not locking the lid ( bad lid lock ) replaced lid lock and recalibrated unit and ran test cycle and lid is now locking and washing checked unit for water leaks and no leaks found at time checked of srv... unit checked fine at this time....
Near Killeen, TX 76542
Mike G.
Job Details: 04/09/2018
NTW4516FW1, Arrived on site for unit will fill but not start washing, checked unit and found that the the unit is not locking the lid ( bad lid lock ) replaced lid lock and recalibrated unit and ran test cycle and lid is now locking and washing checked unit for water leaks and no leaks found at time checked of srv... unit checked fine at this time....
Near Tow, TX 78672
Thomas L.
Job Details: 04/09/2018
Arrived on site for improper operations. Found F9 failure code. Tested unit and power supply. Instructed customer on required voltage to clear F9 code.
Near Austin, TX 78749
Connor M.
Job Details: 04/09/2018
WRT138FZDM00 whirlpool refrigerator Arrived on site to test unit for door seal issue. Found left side of gasket on hinge side had a large gap from top to bottom. Corrected issue with heat gun. Unit working properly, no leaks detected.
Near Cedar Park, TX 78613
Lou
Job Details: 04/09/2018
WMH31017FS0 arrived on site for microwave not turning off when door is open. Upon inspection, I found that the unit would not duplicate the issue. I had to lower the unit in order to remove the UI cover. I removed and replaced the upper and lower interlocks and all switches and found that the upper main switch was bad. Tightened the bolts that hold the unit in place and Tested the unit and unit tested good.
Near Spicewood, TX 78669
Brandon
Job Details: 04/09/2018
Arrived on site for unit making a loud noise during cool down, I found blower fan motor was abnormally loud, I replaced blower motor, unit tested good.
Near Tow, TX 78672
Thomas L.
Job Details: 04/09/2018
Arrived on site for Improper operation. Tested unit. No mater what amount of time I selected, the unit would run only for 2seconds. Replaced control and unit now works properly on all time requests.
Near Killeen, TX 76549
Mike G.
Job Details: 04/09/2018
WTW5000DW0, Arrived on site to install new washplate and recalibrated unit after repair and ran test cycle and unit filled washed drained and is spining checked unit for water leaks and no leaks leaks found at time of srv.... unit is working properly unit checked fine at this time....
Near Killeen, TX 76549
Mike G.
Job Details: 04/09/2018
WTW5000DW0, Arrived on site to install new washplate and recalibrated unit after repair and ran test cycle and unit filled washed drained and is spining checked unit for water leaks and no leaks leaks found at time of srv.... unit is working properly unit checked fine at this time....
Near Georgetown, TX 78628
Jonathan S
Job Details: 04/09/2018
Kitchen Aid oven model #KEBC107KSS0. Arrived on site to disassembled door and clean glass.
Near Belton, TX 76513
Dona
Job Details: 04/09/2018
Arrived on site for washer not advancing through cycles. Found that lid is locking, cycle will begin to fill and wash then all lights will come on control, then they will shut off and will have to wait to start another cycle. Faulty control, replaced control, recalibrated no errors. Ran cycle unit fills, agitates, drains and spins with no errors. Customer swapped so hot and cold are now correct on unit. All water connections dry.
Near Austin, TX 78735
Connor M.
Job Details: 04/09/2018
WRT541SZDM00 whirlpool refrigerator Arrived on site to test unit for not cooling. Found no fans on and compressor not running. Confirmed function of thermostat. Defrost control shorted not sending voltage to thermostat. Replaced and tested unit. Unit working proeprly, no leaks detected. Unit is vacant and has never been occupied.
Near Killeen, TX 76549
Mike G.
Job Details: 04/09/2018
EV161NZTQ01, Arrived on site for unit not freezing/ cooling checked unit and found that the compressor is turning on and unit evap is frosting but found that the vep fan is not working, replaced evap fan motor checked unit and fan is not turning on and unit is now cooling checked unit formwater leaks and no leaks found at time of srv.... unit checked fine at this time.....
Near Killeen, TX 76549
Mike G.
Job Details: 04/09/2018
EV161NZTQ01, Arrived on site for unit not freezing/ cooling checked unit and found that the compressor is turning on and unit evap is frosting but found that the vep fan is not working, replaced evap fan motor checked unit and fan is not turning on and unit is now cooling checked unit formwater leaks and no leaks found at time of srv.... unit checked fine at this time.....
Near Cedar Park, TX 78613
Steve C.
Job Details: 04/09/2018
Arrived on site for the unit is not making ice. Tested the ice maker and found the ice maker has a short. Also the valve solenoid has no resistance. Replaced the ice maker and valve. Tested the unit and unit works properly. All water connections were dry at the time of service.
Near Harker Heights, TX 76548
Dona
Job Details: 04/09/2018
Arrived on site for no heat, found open thermal cut off. Replaced, verified temperatures. Ducting is clean no obstructions. Flow checked good.
Near Austin, TX 78736
Connor M.
Job Details: 04/09/2018
KMHS120ESS0 kitchenaid microwave Arrived on site to install parts for return. Installed control and tested unit. Unit working properly at time of service.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 04/09/2018
Model WDF510PAYB2, Arrived on call for dishwasher not drying dishes, 7-1 which is no heat error, 6-6 which incoming water temp is below 84 degrees, instructed customer on running hot water at sink before starting dishwasher and soap and rinseaid use, also installed heating element due to had 124 ac volts to it but not coming on and tested and is know pulling 8 amps which is good when heat cycle kicks on no water leaks after repair, call complete.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 04/09/2018
Model WDF510PAYB2, Arrived on call for dishwasher not drying dishes, 7-1 which is no heat error, 6-6 which incoming water temp is below 84 degrees, instructed customer on running hot water at sink before starting dishwasher and soap and rinseaid use, also installed heating element due to had 124 ac volts to it but not coming on and tested and is know pulling 8 amps which is good when heat cycle kicks on no water leaks after repair, call complete.
Near Burnet, TX 78611
Thomas L.
Job Details: 04/09/2018
Arrived on site for no heat condition. Found that the heating element has failed causing the unit not to drive. Removed every replaced failed heating element. Unit now operates properly. This is a different issue than the last repair. Dryer and house venting are clear.
Near Round Rock, TX 78681
Lou
Job Details: 04/09/2018
Arrived on site for gapping in freezer gasket. Upon arrival, I found that the fc door gasket had a small gap creating ice buildup in the fc. Also found that the fc door was not properly mounted causing the top of the fc door to lean forward causing the gap. Corrected the problem and the gasket sealed correctly. No water leaks observed during service.
Near Killeen, TX 76542
Dona
Job Details: 04/09/2018
Arrived on site for no drain, found new garbage disposal installed and dishwasher knock out had not been removed so would not allow for unit to drain. Removed knockout, verified operations unit checked good. All water connections dry.
Near Killeen, TX 76542
Dona
Job Details: 04/09/2018
Arrived on site for no drain, found new garbage disposal installed and dishwasher knock out had not been removed so would not allow for unit to drain. Removed knockout, verified operations unit checked good. All water connections dry.
Near Austin, TX 78739
Connor M.
Job Details: 04/09/2018
KRFF707ESS01 kitchenaid refrigerator Arrived on site to test unit for handle issue and freezer drawer issue. Found handle all loose. Corrected issue with allan key. Middle freezer drawer face has broken. Ordering for replacement. Sw approved 4/13
Near Georgetown, TX 78633
Jonathan S
Job Details: 04/09/2018
GE refrigerator model# DSHS9NGYACSS. Not making ice.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 04/09/2018
Model WTW5000DW1, Arrived on call for washer not spining the water out of cloths, checked for error codes and got f0 e5 out of balance load which was the only error, found not parts needed, found customer overloading unit, gave customer instruction on loading and soap usage , no water leaks at time of call, call complete, ran calabration and all checks good, call complete.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 04/09/2018
Model WTW5000DW1, Arrived on call for washer not spining the water out of cloths, checked for error codes and got f0 e5 out of balance load which was the only error, found not parts needed, found customer overloading unit, gave customer instruction on loading and soap usage , no water leaks at time of call, call complete, ran calabration and all checks good, call complete.
Near Burnet, TX 78611
Thomas L.
Job Details: 04/09/2018
Arrived on site and replace torn door gasket. Venting in dryer is clear. Venting in house was discussed with customer. All operations are now normal.
Near New Braunfels, TX 78130
Kevin
Job Details: 04/09/2018
Arrived on site and set unit into diagnostic cycle and found bearing noise during spin, will need to bring back new gear case and have wash play on hand to correct issue. No water leaks from connections at time of service. MVWC415EW
Near Austin, TX 78747
Connor M.
Job Details: 04/06/2018
DU810SWPU4 whirlpool dishwasher Arrived on site to test unit for heater not turning off. Found worn out timer allowing heater to stay on. Replaced and tested unit. Unit working properly, no leaks detected.
Near Jarrell, TX 76537
Dona
Job Details: 04/06/2018
Arrived on site for right front burner never going off of high setting even when on low. Found infinite switch welded on high. Replaced. Verified unit working to spec changing temps. Unit checked good.
Near Austin, TX 78747
Connor M.
Job Details: 04/06/2018
WTW4816FW1 whirlpool washer Arrived on site to test unit for leaking during use. Found tub seal failed allowing water to penetrate gearcase and also corrode shifter. Will need both parts to repair as unit did not spin out water on last two cycles. Allow 2 hours for repair.
Near Hutto, TX 78634
Jonathan S
Job Details: 04/06/2018
Roper dryer model #RED4516FW0. Dryer does not cycle correctly and has long dry times.
Near Burnet, TX 78611
Thomas L.
Job Details: 04/06/2018
Arrived on site install previously diagnosed and ordered parts. Removed and replaced the UI control; tested unit and unit tested good. No water connections to unit due to it sitting outside under the carport. Job completed.
Near Austin, TX 78749
Connor M.
Job Details: 04/06/2018
WMH31017AS2 whirlpool microwave Cap-71.19 diode-52.19 arrived on site to test unit for sparking during use. Found diode burnt up and cap failed. Will need to replace both to repair. Jordan approved tuesday 4/10. Customer needs very last call of day 4pm or later.
Near Temple, TX 76502
Dona
Job Details: 04/06/2018
Arrived on site for left rear, right rear, right front burners turning off when cooking. Will need infinite switches and receptacle harnesses for burners assemblies. Not able to find parts. Discussed with Jordan, AHS will need to research and find parts.
Near Buchanan Dam, TX 78609
Thomas L.
Job Details: 04/06/2018
Arrived on site to inspect no fan on ice machine. Tested unit and found that the condenser fan does not turn on as designed. Attempted to replace the fan and found that the pre-diagnosed part was defective. Ordered new fan and office to schedule return service.
Near Kingsland, TX 78639
Thomas L.
Job Details: 04/06/2018
Arrived on site to install previously diagnosed and ordered parts. Removed and replaced the back drain tube due to it leaking. Tested unit and unit tested good. No water leaks observed after service.
Near Buda, TX 78610
Brandon
Job Details: 04/06/2018
Arrived on site for part hanger, replaced control panel (ss) unit tested good.
Near Austin, TX 78749
Connor M.
Job Details: 04/06/2018
MEDX655DW1 maytag dryer Arrived on site to test unit for nosie during use. Found area of the drum seal folded over allowing scraping. Replaced with prescreen drum and found it to be slightly warped. Will need to order a new drum that is inspected before scheduleing. Part is an expart, office to schedule directly.
Near Austin, TX 78749
Connor M.
Job Details: 04/06/2018
MVWB855DC3 may tag washer File number-7721689710 arrived on site to test unit for leaving residue on clothing and slight clicking sound during aggitation. Customer has already been instructed on proper use and care. Customer has tried changing soaps and following strict soap volume requirements. Customer does not overload machine and washes with affresh monthly. No stored error codes on control. Contacted techline and was told customer needs to use deep water wash and actually increase amount of soap used as the residue is lint from abbrasion and more soap may help lint stay suspended. Found noise coming from slider and clutch. Ordering both for return. Office to schedule directly.
Near Canyon Lake, TX 78133
Daniel A.
Job Details: 04/06/2018
MSF25D4MDM01 Filter not coming out of filter housing. Removed filter housing. Release lever separated from filter housing. Replaced filter housing checked water connections. No leaks detected. Normal operation after service
Near Temple, TX 76501
Dona
Job Details: 04/06/2018
Arrived on site for f:1 error code. Found 240 volts at terminal block. Checked all fuses and cut offs and thermostats. All checked good. Faulty control with error f:1 Jordan assisted with reschedule and parts. Vent is clean.
Near Blanco, TX 78606
Daniel A.
Job Details: 04/06/2018
WRS321SDHW00 Excessive moisture in refrigerator. Refrigerator door not sealing again mullion. Approximately 10-12 inch gap. Removed moisture/condensation. Heated and resealed refrigerator door gasket against mullion. Normal operation after service
Near Kyle, TX 78640
Brandon
Job Details: 04/06/2018
Arrived on site for washer not turning on, found power supply issue, bad outlet. Collected service fee.
Near Kyle, TX 78640
Brandon
Job Details: 04/06/2018
Arrived on site for washer not turning on, found power supply issue, bad outlet. Collected service fee.
Near Austin, TX 78729
Cliff
Job Details: 04/06/2018
Amana washer NTW4605EW0. Arrived on site to diagnose the washing machine that will not complete cycles. Tested unit and found hot and cold water lines switch at wall preventing unit from going into rinse cycle. Corrected waterlines and tested unit. Found all is now functioning properly at this time. No water leaks were found after service was performed.
Near Johnson City, TX 78636
Daniel A.
Job Details: 04/06/2018
MEDB835DW4 Excessive noise/squealing from dryer. Removed front panel Success blower. Corrected blower seal *rubbing on blower ). Repositioned blower housing. Verified belt/idler pulley=rollers operation. Instruct customer on venting /fire hazard. Normal operation after service
Near Temple, TX 76501
Dona
Job Details: 04/06/2018
Arrived on site for LF error, found house water pressure good no blockage. Water is entering unit. Drain hose is in correctly not siphoning water out of unit. Started cycle found unit will get to 1:01 and will stop running after ten minutes unit will display LF and begin to drain. Will then bring error f8 e3- overflow indication. Pressure hose is not kinked do not see any visible signs of air leakage on pressure hose, pressure transducer has failed on main control board. Replaced main control, ran through a full cycle with no errors. All water connections dry.
Near Austin, TX 78737
Connor M.
Job Details: 04/06/2018
GT4175SPB2 whirlpool microwave Arrived on site to install switches and fuse for failure. Installed switches and fuse. Unit working properly at time of service.
Near Johnson City, TX 78636
Daniel A.
Job Details: 04/06/2018
MDB8959SBS3 Not coming on. Control panel replaced previously. Replaced electronic control (not sending voltage to components). Checked water inlet and drain hoses. No leaks detected. Normal operation after service
Near Austin, TX 78744
Luis
Job Details: 04/06/2018
Refrigerator-replaced thermostat
Near Temple, TX 76501
Dona
Job Details: 04/06/2018
Arrived on site for ice chute and motor turning on by itself allowing ice to drop out of front of the door when ice door pad has not been depressed. Voltage is being sent from ui to pads without depressing pads. Replaced ui and ice pad, Turned ice maker back on from where customer had shut off, unit was in harvest once turned back on. Ice maker was always making correct amount of ice problem was ice pad calling to open chute.All water connections dry.
Near Temple, TX 76501
Dona
Job Details: 04/06/2018
Arrived on site for no ice production, ran cycle 57 unit would not harvest, test 45 would allow for water. Bad ice maker motor. Replaced ice maker. Verified unit called for water. All water connections dry. Collected $203.95 for ice maker on card.
Near Austin, TX 78738
Brandon
Job Details: 04/06/2018
Arrived on site for rubber pad missing, I installed rubber pad.
Near Austin, TX 78738
Brandon
Job Details: 04/06/2018
Arrived on site for rubber pad missing, I installed rubber pad.
Near Austin, TX 78737
Connor M.
Job Details: 04/06/2018
WRS325SDAM02 whirlpool refrigerator Arrived on site to test unit for not cooling. Found start relay loose and not connected properly to compressor. Corrected issue and tested unit. Unit working properly, no leaks detected. Collected 159.99
Near Austin, TX 78741
Luis
Job Details: 04/06/2018
Refrigerator-replaced failed damper
Near Wimberley, TX 78676
Daniel A.
Job Details: 04/06/2018
WED75HEFW1 Not heating Verified insufficient voltage. 120 v leg 1. 19 v leg 2. Reset breaker. Verified sufficient voltage. Normal operation after service. Instruct customer on venting/fire hazard
Near Burnet, TX 78611
Mike C.
Job Details: 04/06/2018
Maytag Dryer LDE410 Arrived to find unit making a squeaking sound during operation. Found drum support rollers and pulley bearings worn from normal wear and tear. Installed new support rollers and pulley. Checked operation and unit checks good.
Near Austin, TX 78738
Brandon
Job Details: 04/06/2018
Arrived on site for unit tripping the breaker occasionally, found loose connection at transformer and control board that took out control board and UIB, I replaced appliance manager and UIB and fixed connection, unit tested good.