Near Austin, TX 78728
Cliff
Job Details: 04/13/2018
Whirlpool microwave WMH32519HZ1. Arrived on site to diagnose a microwave with a damaged door. Found microwave door scratched and tops intersection of stainless steel. Replaced microwave door and tested unit. Found all is functioning properly at this time.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 04/13/2018
WTW7300DW1 whirlpool washer Arrived on site to test unit for no fill/ long fill. Found water getting to valves but valve not opening. Replaced valve assy and tested unit. Unit working properly, no leaks detected.
Near Kingsland, TX 78639
Thomas L.
Job Details: 04/13/2018
Arrived on site for no ice conditions. Found the freezer at 0° and the fresh food section at 39° found power to icemaker but icemaker will not cycle. Removed and replaced ice maker. All water connections were dry.
Near Temple, TX 76501
Dona
Job Details: 04/13/2018
Arrived on site for unit not spinning the water out of clothes, found unit with f51 error which is a motor error. Found bolt that holds rotor to bearing and stator had come loose. Retightened ran unit through entire quick wash fully loaded with clothing. Unit ran through entire cycle no errors, clothes spun out completely. Customer stated there was water under the unit after last load. Checked all water connections was not able to find any water leaks on unit. all water connections dry.
Near Temple, TX 76501
Dona
Job Details: 04/13/2018
Case#7721741177 spoke with J.K. Arrived on site for priming noise throughout cycle. Found that the unit is now hooked to water noise has reduced. Cycles are predetermined with turning the valve on and off throughout cycle. No way to reprogram to turn off valve completely. All water connections dry. Venting clear. Unit is working per mfg specifications.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 04/13/2018
KDTE204ESS3 kitchenaid dishwasher Arrived on site to test unit for not drying dishes. Customer is using rinse aid. Confirmed function of heating element. Found customer usually does a load before bed and sometimes doesnt get a chance to unload until later the next day. This can cause water that remains on roof of unit after cycle along with water that condenses there due to cold counter tops to drip back down on dishes when left untouched for too long. Instruct customer on using delay cycle option to decrease length of time dishes remain in unit after cycle is completed. Unit working properly, no leaks detected.
Near Georgetown, TX 78628
Lou
Job Details: 04/13/2018
arrived on site for dishwasher not cleaning well. Upon arrival, customer advised that he dishes were not getting clean. I ran unit through diagnostics and no codes appeared. During test mode, I opened the unit door and found large amounts of soap suds. Also found that the middle and lower wash arms had large amounts of debris in the ports. Cleaned out most of the debris and quoted the customer for the middle wash arm $38.42 and for the lower wash arm $64.94 and labor/service $139.99... Total $263.43. Customer agreed to pay for service fee $108.24 and advised that they would contact the office if they did not want the replacement arms. Remaining balance is $155.19. No water leaks observed during service.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 04/13/2018
Model WTW57ESVW1, Arrived on call for cloths not spinning all the water out, installed parts previous tech ordered and all checks good, unit is draining and spinning as it should and is filling properly, call complete, no water leaks at time of call.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 04/13/2018
Model WTW57ESVW1, Arrived on call for cloths not spinning all the water out, installed parts previous tech ordered and all checks good, unit is draining and spinning as it should and is filling properly, call complete, no water leaks at time of call.
Near Temple, TX 76501
Dona
Job Details: 04/13/2018
Case#7721741177 spoke with J.K. Arrived on site for priming noise throughout cycle. Found that the unit is now hooked to water noise has reduced. Cycles are predetermined with turning the valve on and off throughout cycle. No way to reprogram to turn off valve completely. All water connections dry. Venting clear. Unit is working per mfg specifications.
Near Manor, TX 78653
Joseph C.
Job Details: 04/13/2018
MDB8979SFZ2 Arrived on site for “broken control panel” complaint. Inspected unit and found notch in control panel. Removed and replaced panel. Tested unit. Unit tests good. No leaks detected, at time of service.
Near Manor, TX 78653
Joseph C.
Job Details: 04/13/2018
Near Austin, TX 78726
Luis
Job Details: 04/13/2018
Refrigerator-replaced freezer door
Near Round Rock, TX 78664
Mike C.
Job Details: 04/13/2018
Whirlpool microwave WMH31017FS0 Arrived to install new magnetron, capacitor, diode and mounting hardware. Drilled stripped mounting bolts out and gained access to interior of microwave. Installed new parts and checked operation, checked good.
Near Burnet, TX 78611
Thomas L.
Job Details: 04/13/2018
Near Burnet, TX 78611
Thomas L.
Job Details: 04/13/2018
Arrived and replace both rails as bearing were falling out. Unit now operates correctly.
Near Lorena, TX 76655
Mike G.
Job Details: 04/13/2018
KRFF507EWH01, Arrived on site for unit has a dent on freezer door checked unit and found that the dent is no freezer door replaced door and name plate checked unit and umit checked fine at this time.... checked unit for water leaks and no leaks found at time of srv....
Near Lorena, TX 76655
Mike G.
Job Details: 04/13/2018
KRFF507EWH01, Arrived on site for unit has a dent on freezer door checked unit and found that the dent is no freezer door replaced door and name plate checked unit and umit checked fine at this time.... checked unit for water leaks and no leaks found at time of srv....
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 04/13/2018
Model RH2330XJB3, Arrived on call for fan motor is extremely loud, found that shaft in motor dropped down and allowed the fan blade to rub on the grease filter will need motor kit, per jordan motor has parts lablor and service coverage it is still with in the one year from previous repair for the motor which is covered, no charge to the customer, installed motor kit, call complete.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 04/13/2018
Model RH2330XJB3, Arrived on call for fan motor is extremely loud, found that shaft in motor dropped down and allowed the fan blade to rub on the grease filter will need motor kit, per jordan motor has parts lablor and service coverage it is still with in the one year from previous repair for the motor which is covered, no charge to the customer, installed motor kit, call complete.
Near Austin, TX 78737
Brandon
Job Details: 04/13/2018
Arrived on site for washer not advancing after start up. I put unit into diagnostic test cycle, found cold side fill valve was slow filling, I cleaned out fill valve, put unit into calibration, and another test cycle. Unit tested good.
Near Troy, TX 76579
Mike G.
Job Details: 04/13/2018
WTW5000DW1, Arrived on site to install new motor and cap recalibrated unit after repair and tested unit and unit is now working properly checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Troy, TX 76579
Mike G.
Job Details: 04/13/2018
WTW5000DW1, Arrived on site to install new motor and cap recalibrated unit after repair and tested unit and unit is now working properly checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Georgetown, TX 78628
Lou
Job Details: 04/13/2018
arrived on site for dryer not working. Upon further inspection, I found that the motor was not engaging and unit shut off. After a few minutes, i tested the unit again and the unit turned on. I found that the belt is fraying and the wheels were very dirty and will need to be replaced. Office to order motor, blower wheel, and dryer kit. The dryer kit will need to be installed first and unit tested as the motor may not be needed. Office to schedule return service..04/18 CS. Customer is not available that day and requested the 19th. Lint cleaned during service.
Near Temple, TX 76501
Dona
Job Details: 04/12/2018
Arrived on site for LF error. Unit ran through 3 full cycles with no LF. Customer ran 5 different loads after that and unit did LF in different parts of cycle. Replaced faulty valve and pressure hose to correct LF. Ran through full cycle bulky/ normal unit did not give LF error. Customer will monitor. All water connections dry.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 04/12/2018
Model MVWC565FW0, Arrived at 10:54 am and unit was not axcessable, returned at the end of day, Arrived on call for previous diag. And function found that has failed is water valve on hot side, replaced water valve, unit is ready for resale, unit is not connected to water, call complete.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 04/12/2018
Model MVWC565FW0, Arrived at 10:54 am and unit was not axcessable, returned at the end of day, Arrived on call for previous diag. And function found that has failed is water valve on hot side, replaced water valve, unit is ready for resale, unit is not connected to water, call complete.
Near Georgetown, TX 78628
Jonathan S
Job Details: 04/12/2018
Whirlpool washer model #WTW5000DW1. Not completing cycle.
Near Burnet, TX 78611
Thomas L.
Job Details: 04/12/2018
Arrived on site for no ice condition. Found icemaker to have a defective drive Motor. Replaced and tested. Water connections were dry. Customer I needs to correct very low water pressure to unit.
Near Austin, TX 78744
Luis
Job Details: 04/12/2018
Refrigerator-remolded freezer door gasket
Near Bruceville-Eddy, TX 76524
Dona
Job Details: 04/12/2018
Arrived on site for chirping noise throughout wash, found rotor loose on stator causing noise. Suspension good, no errors. All water connections dry. Ran through full normal cycle-with no abnormal noises. Agitate sounds correct, spin smooth.
Near New Braunfels, TX 78130
Connor M.
Job Details: 04/12/2018
WRF767SDEM00 whirlpool refrigerator Arrived on site to test unit for making too much ice. Found ice level arm not attached to icemaker at pivot point. Corrected issue and tested unit. Instruct on proper use and care. Unit working properly, no leaks detected.
Near Temple, TX 76502
Lou
Job Details: 04/12/2018
arrived on site for sheet stuck in washer. Upon further inspection, I found that a sheet was caught/stuck under the agitator. I removed the agitator and removed the sheet and found that the agitator had plastic pieces broken on the bottom. I installed a new agitator and ran the unit in diagnostic mode. The unit read error codes F3e2, f7e8, f7e2, f0e4. Cleared the codes and continued with test mode and unit tested good. No error codes and no water leaks observed.
Near Round Rock, TX 78681
Jonathan S
Job Details: 04/12/2018
Whirlpool gas cooktop model# GLT3657RB01.
Near Austin, TX 78748
Luis
Job Details: 04/12/2018
Refrigerator-replaced thermistor assembly
Near Buda, TX 78610
Connor M.
Job Details: 04/12/2018
GI6SARXXF05 whirlpool refrigerator RF360-169.99 icemaker-94.99 arrived on site to test unit for not making ice. Found icemkaer heating element failed causing ice to remain fused to mold during harvest. Found model number on record is incorrect. Ordering correct icemaker for return. Jordan approved 4/16 collected svc via cc
Near Temple, TX 76501
Dona
Job Details: 04/12/2018
Arrived on site for unit not spinning clothes at end of cycl, found shifter error shifter not engaging. Replaced shifter and calibrated unit checked good. All water connections dry.
Near Harker Heights, TX 76548
Steve C.
Job Details: 04/12/2018
Near Spring Branch, TX 78070
Daniel A.
Job Details: 04/12/2018
KUDE40FXPA4 Leaking water during use. Outlet tub clamp hose separated from sump. Replaced with new clamp. Checked water inlet and drain hoses. No leaks detected. Ran wash cycle. Normal operation after service
Near Belton, TX 76513
Lou
Job Details: 04/12/2018
arrived on site for washer not turning on. Customer advised that she ran the unit and while draining, the unit shut off and will not turn on. Unit was unplugged upon arrival. I plugged the unit in and received no power to the unit. I installed a new control and the unit came on. Placed the unit in manual test mode to drain the water and the drain pump sounded as if was dragging. I removed and replaced the drain pump and tested the unit in diagnostic mode. Unit operated as designed. No water leaks observed during service. I instructed the customer on proper detergent and softner use.
Near Austin, TX 78704
Joseph C.
Job Details: 04/12/2018
KDTE104ESS3 Arrived on site for “not draining/control panel error” complaint. Inspected unit and found shorted power wires had blown control. Removed and replaced control. Repaired short in junction box. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78704
Joseph C.
Job Details: 04/12/2018
Near Burnet, TX 78611
Thomas L.
Job Details: 04/12/2018
Arrived on site for water leaking into fresh food section. Found the defrost drain line had frozen. Defrosted and tested.
Near Burnet, TX 78611
Thomas L.
Job Details: 04/12/2018
Arrived on site no ice condition. Found unit to have any evaporator leak. Unit also had a defective condenser fan motor. It also had a defective recirculation pump. Replaced all and tested well.
Near Austin, TX 78749
Connor M.
Job Details: 04/12/2018
MEDX655DW1 maytag dryer Arrived on site to install drum for failure. Installed and tested unit. Unit working properly. Made customer aware of proper venting and fire hazard. Returning failed drum to storage.
Near Temple, TX 76502
Dona
Job Details: 04/12/2018
Arrived on site for light staying on constantly unless bulb removed. Found interlock switches causing flicker replaced secondary and primary. Unit no longer flickers. Relay on control 7104 is stuck will not allow for light to turn off. Replaced control and UI light shuts off all functions check good.
Near Austin, TX 78737
Luis
Job Details: 04/12/2018
Refrigerator-replaced icemaker
Near Austin, TX 78748
Connor M.
Job Details: 04/12/2018
WED4815EW1 whirlpool dryer Arrived on site to test unit for noise during use. Completely dissasembled dryer at front and back. Nothing unusual found. Ran dryer without drum and had no noise. After reassembling unit making sure to tighten every screw very well i still had the same noise. Observed drum while operating by jumping door switch and found some wobbleing at drum. Ordering drum for return.
Near Austin, TX 78757
Nathaniel B.
Job Details: 04/12/2018
Model MGD5500FW0, Arrived on call for dryer not heating and vents have been cleaned, know unit is not turning on at all, installed ui and then checked for error codes and got f6e1 which is a communication error between ui and acu, f2 e1 which is a stuck key error, f3 e6 moisture senser open, f4 e3 restricted air flow vent is cleared and ui has been replaced due to burn mark on the control and all errors but the moisture senser error, went to main control on p13 and checked ohms and got open moisture senser, called office and spoke to jordan and office will contact customer on monday about service fee due to found a functional issue with the machine that would effect dry times, per sarah will reschedule with moisture senser on 4/16/18, dryer vent has been cleaned.
Near Austin, TX 78757
Nathaniel B.
Job Details: 04/12/2018
Model MGD5500FW0, Arrived on call for dryer not heating and vents have been cleaned, know unit is not turning on at all, installed ui and then checked for error codes and got f6e1 which is a communication error between ui and acu, f2 e1 which is a stuck key error, f3 e6 moisture senser open, f4 e3 restricted air flow vent is cleared and ui has been replaced due to burn mark on the control and all errors but the moisture senser error, went to main control on p13 and checked ohms and got open moisture senser, called office and spoke to jordan and office will contact customer on monday about service fee due to found a functional issue with the machine that would effect dry times, per sarah will reschedule with moisture senser on 4/16/18, dryer vent has been cleaned.
Near Temple, TX 76502
Dona
Job Details: 04/12/2018
Arrived on site to check for resale, found all components ohm correctly, no structural or cosmetic damage, unit holds water. No power cord available. Unit checks to spec per ohm checks and no leaks found. Unit does not look to have been run at all.
Near Austin, TX 78749
Luis
Job Details: 04/12/2018
Refrigerator-installed a uv drier recharged system
Near Hutto, TX 78634
Jonathan S
Job Details: 04/12/2018
Kitchen Aid dishwasher model # KDTM354DSS4. Not cleaning dishes and leaving soap film on dishes.
Near Austin, TX 78748
Connor M.
Job Details: 04/12/2018
MHWE201YW00 maytag washer Arrived on site to test unit for not unlocking or starting cycles, and banging noise during use. Found error code f3e2 indicating failed temp thermistor. Will return with shocks incase needed after running test. Sw approved 4/18
Near Austin, TX 78746
Luis
Job Details: 04/12/2018
Refrigerator-installed updated ice door and motor
Near Belton, TX 76513
Lou
Job Details: 04/12/2018
arrived on site for no water in dishwasher. Upon further inspection, I placed the unit in diagnostic mode and tested. No water entered the unit. Due to this being a new home and new construction in the area, I disconnected the water line and flushed it out. Small amounts of debris was in the line. Reconnected the water line and placed unit in test mode and unit operated designed. Water pressure at the outlet seemed high. I checked the water pressure and it was at 80psi. No water leaks observed during service. Instructed customer on detergent use and care for the unit.
Near San Marcos, TX 78666
Connor M.
Job Details: 04/12/2018
WRX988SIBM01 whirlpool refrigerator Arrived on site to install part for repair. Installed thermistor. Insstalled defrost thermistor per whirlpool svc pointer. Unit working properly at time of service. No leaks detected.
Near New Braunfels, TX 78130
Daniel A.
Job Details: 04/12/2018
WOD51EC0AS01 F5e1 error code. Contacted tech assist. After clean cycle upper latch not releasing. Replaced upper latch switch/motor assembly. Verified normal operation after service
Near San Marcos, TX 78666
Connor M.
Job Details: 04/12/2018
KDTE204GPS0 kitchenaid dishwasher Arrived on site to test unit for upper rack issue. Found both slides had locked up and completely failed when builder pulled rack out to adjust. Replaced left and right hand slides. Unit working as designed. No leaks detected.
Near San Marcos, TX 78666
Connor M.
Job Details: 04/12/2018
WRF989SDAE00 whirlpool refrigerator Arrived on site to test unit for leaking from filter after replacement. Found no evidence of bad filter. Water leaks from filter head when turned on. Will need to replace filter head to repair. CS approved monday 4/16 am requested
Near Austin, TX 78735
Brandon
Job Details: 04/12/2018
Arrived on site for dryer shutting down after a few minutes and displaying an error code e01 f03. I removed control panel, tested resistance on p4 connector/thermistor, thermistor was in range of temperatures, tested good, also tested wire harness, tested good. Found the p4 connector was loose at the board, I plugged in p4 connection properly, unit tested good.
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details: 04/12/2018
Arrived on site for unit tripping breaker. Upon arrival I found unit totally in operable. Reset breaker and it instantly tripped. Remove unit from wall to find defective house wiring connections. Instructed Customer to have wiring connections repaired.
Near Kyle, TX 78640
Robert
Job Details: 04/12/2018
Arrived on job for complaints of leaks. Found valve for cold water broken and causing leak. Replaced
Near Salado, TX 76571
Lou
Job Details: 04/12/2018
arrived on site to inspect dryer door not closing. Upon inspection, I found that the dryer door latch would not open up properly and the door strike would not insert unless the door was slammed. I removed and replaced the latch and tested the door and it closed properly. No lint observed during service.
Near Morgan's Point Resort, TX 76513
Dona
Job Details: 04/12/2018
Arrived on site for no cool in unit. Found compressor trying to start drawing 15 amps then shutting down. Faulty start device, replaced start device. Compressor started and temperatures started to drop. Frost pattern looked good, let customer know to wait 24 hours before loading so that temperatures could be correct. All water connections dry.
Near Kyle, TX 78640
Robert
Job Details: 04/12/2018
Arrived on job for complaints of not making ice. Found water valve with loose connection. Secure wir
Near Kyle, TX 78640
Robert
Job Details: 04/12/2018
Near Cedar Park, TX 78613
Lou
Job Details: 04/11/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the sump/motor and control. Tested unit in diagnostic mode and the unit operated as designed. No water leaks observed during service.
Near Austin, TX 78739
Connor M.
Job Details: 04/11/2018
WED92HEFC0 whirlpool dryer Arrived on site to test unit for water coming from vent inside and long dry cycles. Found when dryer is running there is very little if any air movment at vent output outside of the house. This will cause water that has been evaporated from clothes to condense before leaving the unit. No issues with dryer. Instruct custome ron conatcting a vent cleaning company. Made aware of proper venting and potential risks of poor ducting.
Near Austin, TX 78738
Luis
Job Details: 04/11/2018
Refrigerator-installed new drain pan
Near Austin, TX 78756
Scott
Job Details: 04/11/2018
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 04/11/2018
Model WMH31017FS0, Arrived on call for relay on main control shorted 2 contActs, causing bulb to burn or weld light socket to bulb, replaced control and tested light, light and socket replaced by prior tech, all checks good, under light is going on and off know, also found when opening and closing the microwave door the interior light flickers on and off, will need to order interlocks and switches, also found control panel not able to mout which is a electrical hazzard will need to order control housing, skyped office parts and talked to jordan and will reschedule for 4/16/18
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 04/11/2018
Model WMH31017FS0, Arrived on call for relay on main control shorted 2 contActs, causing bulb to burn or weld light socket to bulb, replaced control and tested light, light and socket replaced by prior tech, all checks good, under light is going on and off know, also found when opening and closing the microwave door the interior light flickers on and off, will need to order interlocks and switches, also found control panel not able to mout which is a electrical hazzard will need to order control housing, skyped office parts and talked to jordan and will reschedule for 4/16/18
Near Temple, TX 76501
Dona
Job Details: 04/11/2018
Arrived on site for unit starting self clean in off position, found burned motor and wiring. Control relays turning oven on when nothing has been pressed. Will need control that is showing nla, motor and oven wire harness. Melissa assisted with part inquiry. Unit is unplugged position upon leaving home.
Near Austin, TX 78739
Connor M.
Job Details: 04/11/2018
KFCS22EVMS8 kitchenaid refrigerator File number-7721728550 arrived on site to test unit for low ice production. Found temp between 4 and 6f in freezer. Airflow optimal. Contacted techline and was told it is likely the door switch not being engaged properly. Ordeirng actuator pad for return. Sw approved 4/16
Near Austin, TX 78756
Scott
Job Details: 04/11/2018
RTW4516FW1
Near Temple, TX 76501
Dona
Job Details: 04/11/2018
Arrived on site for no operation, with f1 error code. Replaced main control board, verified temperatures. All operations checked good de-linted on previous diagnosis visit. Ducting is clear.
Near Temple, TX 76504
Mike G.
Job Details: 04/11/2018
WTW5000DW1, Arrived on site for unit will take long to fill checked unit and found that the lid lock is not locking and when filling water valve will turn on and off when filling found that the control is bad replaced control and tested unit and unit is now locking and is filling properly ran test cycle and unit ran all test fine checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time.....
Near Temple, TX 76504
Mike G.
Job Details: 04/11/2018
WTW5000DW1, Arrived on site for unit will take long to fill checked unit and found that the lid lock is not locking and when filling water valve will turn on and off when filling found that the control is bad replaced control and tested unit and unit is now locking and is filling properly ran test cycle and unit ran all test fine checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time.....
Near Austin, TX 78739
Connor M.
Job Details: 04/11/2018
KRFF507ESS01 kitchenaid refrigerator RF170-199.99 arrived on site to test unit for loud noise from freezer. Found frost build up on evap. No excess frost build up close to defrost heating element indicating successful defrost cycles. Fiund evidence of door being left open as the gasket is sealing well. All compontents checked fine. Defrosted unit with steamer. Frost pattern checked good after start up. Collected for evap defrost. No leaks detected. Customer paid via check.
Near Cedar Park, TX 78613
Lou
Job Details: 04/11/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the control, heater, both tracks, and stops. Tested unit in diagnostic mode and unit operates as designed. No water leaks observed during service.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 04/11/2018
Arrived on site for Noisey operation. Found manufacturers water line vibrating against Lowe access panel. Insulated water line to eliminate issue. Water connections were all dry.
Near Wimberley, TX 78676
Daniel A.
Job Details: 04/11/2018
MEDC300BW0 Dryer not coming on verified door switch operation. Checked voltage. Shorted element caused thermal fuse to fail. Replaced heater/thermal fuse . Normal operation after service
Near Temple, TX 76504
Dona
Job Details: 04/11/2018
Arrived on site for no heated dry. Found right side wire to heating element not connected to element. Wire was stuck with other wires to owi sensor. Attached wire verified heater turning on all water connections dry. Unit checked good.
Near Dripping Springs, TX 78620
Luis
Job Details: 04/11/2018
Refrigerator-replaced fresh food thermistor harness
Near Austin, TX 78754
Nathaniel B.
Job Details: 04/11/2018
Model CHW9060AW0, Arrived on call for washer vibrating during use, skocks are covered under warranty but svc/ labor is not and svc/labor is fl570 189.99 plus tax 15.67 which =205.66, customer agreed to est, installed shocks and tested and all checks good, call complete, office will collect full balance of 205.66, no water leaks at time of call, call complete.
Near Austin, TX 78754
Nathaniel B.
Job Details: 04/11/2018
Model CHW9060AW0, Arrived on call for washer vibrating during use, skocks are covered under warranty but svc/ labor is not and svc/labor is fl570 189.99 plus tax 15.67 which =205.66, customer agreed to est, installed shocks and tested and all checks good, call complete, office will collect full balance of 205.66, no water leaks at time of call, call complete.
Near Cedar Park, TX 78613
Lou
Job Details: 04/11/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the ice door kit. Tested unit and the unit operated as designed. No water leaks observed during service.
Near Austin, TX 78737
Luis
Job Details: 04/11/2018
Refrigerator-installed updated fresh food evaporator,compressor and filter drier
Near Highland Haven, TX 78654
Thomas L.
Job Details: 04/11/2018
Arrived on site for icemaker leaking and no ice. Found ice maker was turned off. Later cycled icemaker and it was leaking from mold. Replaced and tested. All water connections were dry.
Near Georgetown, TX 78626
Steve C.
Job Details: 04/11/2018
Near Georgetown, TX 78626
Steve C.
Job Details: 04/11/2018
Arrived on site for the unit is not cooling or freezing. Tested the unit and found the compressor is not turning on. Found the start relay is loose and secured the connection. Tested the unit and unit works properly. All water connections were dry at the time of service.
Near Georgetown, TX 78626
Steve C.
Job Details: 04/11/2018
Arrived on site to replace the air diffuser due to the diffuser is extremely noisy when opening and closing. Replaced the part and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Georgetown, TX 78626
Steve C.
Job Details: 04/11/2018
Arrived on site to replace the air diffuser due to the diffuser is extremely noisy when opening and closing. Replaced the part and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Round Rock, TX 78665
Jonathan S
Job Details: 04/11/2018
Whirlpool refrigerator model# WRS571CIDM02. Making louder than normal noises.
Near Austin, TX 78754
Nathaniel B.
Job Details: 04/11/2018
Model ADB1400AGS1, Arrived on call for dishwasher not draining, found that the knock out was not knocked out by lowes installers, called office and spoke to erica due to customer does not want to pay service fee, per erica office will bill customer due to they were instructed customer instructs are not covered, also unit was not mounted to cabinet, adjusted leveling legs but could not screw in to counter top due to customer would not sign disclaimer to screw the two metal tabs to the bottom of the counter top due to it is close to the laminate that will break or chip, customer said they would screw it in to they counter top, no water leaks at time of call, call complete, office will collect 108.24 by billing the customer.
Near Austin, TX 78754
Nathaniel B.
Job Details: 04/11/2018
Model ADB1400AGS1, Arrived on call for dishwasher not draining, found that the knock out was not knocked out by lowes installers, called office and spoke to erica due to customer does not want to pay service fee, per erica office will bill customer due to they were instructed customer instructs are not covered, also unit was not mounted to cabinet, adjusted leveling legs but could not screw in to counter top due to customer would not sign disclaimer to screw the two metal tabs to the bottom of the counter top due to it is close to the laminate that will break or chip, customer said they would screw it in to they counter top, no water leaks at time of call, call complete, office will collect 108.24 by billing the customer.
Near Austin, TX 78745
Connor M.
Job Details: 04/11/2018
M1BXXLZYB00 maytag refrigerator Arrived on site to test unit for freezing food in rear of unit. Found fridge at max capacity with many items hanging off back of shelf up against liner. Food in this area will freeze due to air circulation. Instruct customer on proper use and care. No leaks detected.
Near Austin, TX 78745
Connor M.
Job Details: 04/11/2018
WTW4816FW1 whirlpool washer Arrived on site to install parts for repair. Installed gearcase and actuator. Unit working properly at time of service. No leaks detected.
Near Buda, TX 78610
Diego G.
Job Details: 04/11/2018
Arrived on site. Checked for advancing issues. Found timer faulty cuasing timer not advance threw cycle. Replaced timer, all functions tested ok. Job complete.