Near Georgetown, TX 78633
Mike G.
Job Details: 05/23/2018
KGCU462VSS02, Arrived on site for cooktop SCRATCHED, checked unit and found that the control panel is scratched and will need to be replaced ordering part per CS will only need 1 tech and 1hr to do repair per JA r/s next apt for 5/25/18 but customer is wanting next apt for 5/29/18
Near Georgetown, TX 78633
Mike G.
Job Details: 05/23/2018
KGCU462VSS02, Arrived on site for cooktop SCRATCHED, checked unit and found that the control panel is scratched and will need to be replaced ordering part per CS will only need 1 tech and 1hr to do repair per JA r/s next apt for 5/25/18 but customer is wanting next apt for 5/29/18
Near The Hills, TX 78738
Brandon
Job Details: 05/23/2018
Arrived on site for part hanger, I replaced drain pump, unit tested good water lines were dry at time of service.
Near Meadowlakes, TX 78654
Thomas L.
Job Details: 05/23/2018
Arrived on site for or drying conditions. Tested water to find it at 126 degrees at sink and 94 in unit at first fill. customer to run water at sink 1st. Filled up drying agent. Increase drying agent setting. Customer to have drain hose elevated. All water connections were dry.
Near Austin, TX 78731
Cliff
Job Details: 05/23/2018
Whirlpool dishwasher WDT710PAYM3. Arrived on site to install rack stop for dishwasher. Replaced stop and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Austin, TX 78717
Lou
Job Details: 05/23/2018
arrived on site to inspect dishwasher not drying. Open further inspection, I placed the unit in diagnostics and tested. Unit operated as designed. I explained to the customer that due to the unit having a plastic tube, the plastic is going to absorb the heat and will not dry like a unit with a stainless steel tub where the heat will retract and dry the dishes much better. Customer advised that she does not like the unit and will work with her builder to replace the unit. No water leaks observed during service.
Near Kyle, TX 78640
Kevin
Job Details: 05/23/2018
Arrived on site and started dryer on a normal cycle and found a grinding noise during operation. Found metal debris stuck in the felt ring that is making noise. After clearing noise has stopped, no lift found in unit cabinet at time of service, job complete.
Near Temple, TX 76504
Dona
Job Details: 05/23/2018
Arrived on site for high temps in refrigerator, found 4 inch ice build up on evaporator, customer started defrost process tech completed defrost. Replaced rc therm and control. Verified operations, unit temps are dropping and door is sending signal when open. All water connections dry.
Near Georgetown, TX 78633
Mike G.
Job Details: 05/23/2018
KMHS120ESS5, Arrived on site for unit say open and close door checked unit and found that the door switches are bad replaced all 3 door switches and checked unit and unit is working properly unit checked fine at this time....
Near Georgetown, TX 78633
Mike G.
Job Details: 05/23/2018
KMHS120ESS5, Arrived on site for unit say open and close door checked unit and found that the door switches are bad replaced all 3 door switches and checked unit and unit is working properly unit checked fine at this time....
Near San Marcos, TX 78666
Connor M.
Job Details: 05/23/2018
WRS571CIDM01 whirlpool refrigerator Arrived on site to install paets for repair. Installed ice bin and ice door. Unit working properly, no leaks detected. If issue persists freezer door will be needed.
Near Pflugerville, TX 78660
Jonathan S
Job Details: 05/23/2018
Whirlpool refrigerator model# WRX735SDBM02. Not making ice. Ice maker making loud noises. Water disp
Near Austin, TX 78703
Luis
Job Details: 05/23/2018
Icemachine. Replaced ice cutter grid assembly
Near Marble Falls, TX 78654
Thomas L.
Job Details: 05/23/2018
Arrived on site for no ice dispensing condition. Found motor turning shaft but not auger. Auger in bin ice cracked. Replaced bin. All water connections were dry.
Near Kyle, TX 78640
Kevin
Job Details: 05/23/2018
Home is on a new Street, took one picture of location on map. Arrived on site and inspected refrigerator and found freezer door is closing properly, soft clothes only works on the last 3 inches of movement. Middle drawer in freezer is broken and front will not stay on. Will need to bring back a new drawer to correct issue. No water leaks from connections at time of service.
Near Harker Heights, TX 76548
Dona
Job Details: 05/22/2018
Arrived on site for unit not advancing, unit is full of water, lid switch checks good. Unit would not fill at all was not sending voltage to motor. timer motor not advancing, customer stated that only part of timer has been working for a while. Next tech replaced timer, unit would then fill but not advance cycles, found bad pressure switch and intermittent lid switch. Replaced pressure switch, and lid switch. Unit is filling, stopping fill on correct water level. Checked water shut off on load size 6 times to verify no overflow. Unit agitating, spinning and draining. All water connections dry.
Near Harker Heights, TX 76548
Dona
Job Details: 05/22/2018
Arrived on site for unit not advancing, unit is full of water, lid switch checks good. Unit would not fill at all was not sending voltage to motor. timer motor not advancing, customer stated that only part of timer has been working for a while. Next tech replaced timer, unit would then fill but not advance cycles, found bad pressure switch and intermittent lid switch. Replaced pressure switch, and lid switch. Unit is filling, stopping fill on correct water level. Checked water shut off on load size 6 times to verify no overflow. Unit agitating, spinning and draining. All water connections dry.
Near Liberty Hill, TX 78642
Lou
Job Details: 05/22/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the door, door gasket with high temp adhesive, and the water valve and hose. Tested unit and unit tested good. No water leaks observed during service.
Near Harker Heights, TX 76548
Dona
Job Details: 05/22/2018
Arrived on site for unit stopped mid cycle, no operation, found open fuse and burned connector on control. Replaced main control and open fuse. Verified operations all check good. All water connections dry.
Near Pflugerville, TX 78660
Joseph C.
Job Details: 05/22/2018
KDTM354DSS5 Arrived on site for “broken dispenser door” complaint. Inspected unit and found broken dispenser door. Removed and replaced dispenser. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Hays, TX 78610
Kevin
Job Details: 05/22/2018
Arrived on site and found all LEDs including freezer are not coming on when doors are open. Reset all connections on LED power supply board and lights are working again. LED power supply board will need to be replaced in order to correct issue.
Near Killeen, TX 76542
Dona
Job Details: 05/22/2018
Arrived on site for unit not always heating, found unit is heating on timed dry but not on energy preferrred. Will need to replace timer and thermostat. Will bring element should not be needed as unit is heating. Dry vent cleared. Jordan assisted with reschedule and parts.
Near Liberty Hill, TX 78642
Lou
Job Details: 05/22/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the glass cooktop. Tested unit and unit operated as designed. Job completed.
Near Austin, TX 78741
Connor M.
Job Details: 05/22/2018
NED4655EW1 Amana dryer Arrived on site to test unit for dryer not heating. Found improper voltage coming to terminal block. Instruct in contacting an electrician. Made aware of proper venting and fire hazard.
Near Killeen, TX 76549
Dona
Job Details: 05/22/2018
Arrived on site for unit not fully draining, found drain level is correct on machine, seals are below water line to keep wet, verified unit draining in cycle, and at end of cycle. Line to garbage disposal is clear water ran freely. All water connections dry. Unit is running to spec. Explained water level to customer.
Near Killeen, TX 76549
Dona
Job Details: 05/22/2018
Arrived on site for no functionality, found control is dead. No lights voltage to board checks correctly. Replaced main control. Verified operations, calibrated, unit filled, agitates, drains and spins. All water connections dry all parms check correct.
Near Liberty Hill, TX 78642
Lou
Job Details: 05/22/2018
arrived on site to inspect cooktop Ignitor constantly clicking. Upon further inspection, I found that the left rear burner valve is sticking causing it to constantly click or attempt to ignite. Also found that the right rear burner flame was only burning on the right side and barely flaming out on the left side of the burner. Office to order left rear valve and right rear burner head/orifice holder and schedule return service for 05/29/18 CS. No gas leaks detected during service.
Near Austin, TX 78735
Kevin
Job Details: 05/22/2018
Arrived on site and replaced flowmeter diagnosed on previous visit, ran a diagnostic cycle and leaking has stopped. Also no water leaks from connections at time of service, job complete
Near Austin, TX 78741
Connor M.
Job Details: 05/22/2018
WRS571CIDM02 whirlpool refrigerator Arrived on site to test unit for making loud noise when opening and closing door. Found diffuser operating loudly. Replaced and tested unit. Unit working properly, no leaks detected.
Near Austin, TX 78745
Connor M.
Job Details: 05/22/2018
WTW5000DW whirlpool washer Arrived on site to test unit for not completeing cycle. Found error code for failed thermistor. Replaced valve and tested unit. Unit working properly, no leaks detected.
Near Austin, TX 78746
Kevin
Job Details: 05/22/2018
Arrived on site and found all LEDs in fresh food and freezer section are not operating. After replacing they will now turn on properly. No water leaks from connections at time of service, job complete.
Near Austin, TX 78733
Kevin
Job Details: 05/22/2018
Arrived on site and found front left and right burners do not ignite consistently. Right burner only needed electrode adjustment as it was not sparking consistently in one direction. Bending it closer to burn her head correct it’s operation. Left front electrode had failed and after replacing it is now working properly. Quoted the customer for one electrode and remaining labor to replace it. Job complete.
Near Austin, TX 78717
Lou
Job Details: 05/22/2018
arrived on site to inspect dishwasher dispenser not closing. Upon further inspection, I found that the latch on the dispenser was broken. I removed and replaced the dispenser and placed the unit in diagnostics. Unit operated as designed. No water leaks observed during service.
Near Austin, TX 78717
Lou
Job Details: 05/22/2018
Arrived on site to inspect oven door handle loose. Upon further inspection, I found that the vent trim was badly damaged and missing two screws. Where the handle screws into the vent trim was broken off and the the that attaches the handle to the vent trim and the screw test attaches the handle/vent trim to the door were missing. Also, the handle was badly damaged, as well. I removed and replaced the vent trim and handle and returned the door to the oven unit. Unit operated as designed.
Near Spicewood, TX 78669
Cliff
Job Details: 05/22/2018
Maytag washer MVWC416FW0. Arrived on site to diagnose a washing machine with an agitator that is coming off of driveshaft. Tested unit and found wash plate and barrel sections of agitator both damaged due to loose bolt. Also bolt does not appear to of had any Loctite from manufacturing to prevent loosening of the bolt over time. Replaced Washplate, bolt and barrel and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Robinson, TX 76706
Mike G.
Job Details: 05/22/2018
Arrived on site for CLOTHING STUCK UNDER AGITATOR, checked unit and found that the agitator is warped removed clothing and replaced agitator and checked unit and unit checked fine at this time... , MVWB765FW0
Near Robinson, TX 76706
Mike G.
Job Details: 05/22/2018
Arrived on site for CLOTHING STUCK UNDER AGITATOR, checked unit and found that the agitator is warped removed clothing and replaced agitator and checked unit and unit checked fine at this time... , MVWB765FW0
Near Austin, TX 78739
Connor M.
Job Details: 05/22/2018
GS6NBEXRS01 whirlpool refrigerator Arrived on site to test unit for leaking. Found coupling at bottom fo door loose, water line not seated correctly. Corrected issue and tested unit. Unit working properly, no leaks detected.
Near Manor, TX 78653
Joseph C.
Job Details: 05/22/2018
WRS325FDAM04 Arrived on site for “shoots ice out of dispenser” complaint. Inspected unit and found dispenser door closing too soon. Adjusted closer. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Manor, TX 78653
Joseph C.
Job Details: 05/22/2018
WMH32519FS1 Arrived on site for “door open error” complaint. Inspected unit and found door switches and interlocks faulty. Removed and replaced door switches and interlocks. Unit tests good.
Near Briarcliff, TX 78669
Cliff
Job Details: 05/22/2018
Kitchenaid refrigerator KRFC302EPA00. Arrived on site to diagnose a refrigerator with a door that is not closing properly. Tested unit and found due to the heavy custom paneling door has dropped over time. Adjusted hinges and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near New Braunfels, TX 78130
Diego G.
Job Details: 05/22/2018
Arrived on site. Check for icemaker issues. Found module bad on ice maker. Replaced ice maker and cycled, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 05/22/2018
Arrived on site. Check for icemaker issues. Found module bad on ice maker. Replaced ice maker and cycled, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 05/22/2018
Arrived on site. Check for icemaker issues. Found module bad on ice maker. Replaced ice maker and cycled, all functions tested OK. No leaks present. Job complete
Near Bee Cave, TX 78738
Brandon
Job Details: 05/22/2018
Arrived on site for frost build up in freezer section, found frame of unit needed sealant around freezer section to make a better seal. I used sealant from truck stock to seal the unit, tested good. Water lines were dry at time of service.
Near Austin, TX 78745
Connor M.
Job Details: 05/22/2018
MEDC215EW1 maytag dryer Installed timer, squeak coming from idler pulley. Added a drop of lube and ran for twenty mins no squeak. Unit working properly. Instruct on proper venting.
Near Harker Heights, TX 76548
Dona
Job Details: 05/22/2018
Arrived on site for no operation and error, previous tech installed control that was faulty. Found open thermal fuse upon return. Replaced thermal fuse wp3392519 used from 187201 Kristen and sarah assisted. Verified operations and temperatures. Airflow seems good, instructed customer to have duct work checked throughout the year. Ducting clear. All parms check good.
Near Lorena, TX 76655
Mike G.
Job Details: 05/22/2018
WTW8500DC4, Arrived on site for unit not cleaning, checked unit in test cycle and unit ran all test with no issues Recalibrated unit and ran unit with load of towels and unit filled washed and drained and rinsed and is spining and lid is locking and unlocking checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time......
Near Lorena, TX 76655
Mike G.
Job Details: 05/22/2018
WTW8500DC4, Arrived on site for unit not cleaning, checked unit in test cycle and unit ran all test with no issues Recalibrated unit and ran unit with load of towels and unit filled washed and drained and rinsed and is spining and lid is locking and unlocking checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time......
Near Austin, TX 78748
Connor M.
Job Details: 05/22/2018
WED5000DW whirlpool dryer Arrived on site to test unit for no heat. Found element cycling properly with door open. Found about 6 feet of duct crushed into about 4 inches causing poor air flow. Instruct customer on replaceing and or shortneing dryer duct. Made aware of proper veting and fire hazard.
Near Austin, TX 78734
Brandon
Job Details: 05/22/2018
Arrived on site for loud humming noise, found sump to be faulty, I replaced sump, unit tested good. Water lines were dry at the time of service.
Near Cedar Park, TX 78613
Lou
Job Details: 05/22/2018
arrived on site to inspect dishwasher dispenser not opening. Upon further inspection, I found that the units dispenser components are plastic and due to their age they are worn and are not functioning properly. I tested the unit by taking the inner door liner off and verifying the connection between the cam and the actuator but the teeth on the actuator are worn as are on the cam. The door latch is worn as well. Office to order latch kit, actuator, dispenser, draw bar, spring, dispenser door, door spring, pin dowel, drip cover, and follower/cam. Office to schedule return service. No water leaks observed during service.
Near Killeen, TX 76542
Dona
Job Details: 05/22/2018
Arrived on site for noise in spin, found nut to pulley on gearcase loose, allowing for noise between shift actuator change and spin. Retightened, verified operations. No errors, all water connections dry all parms check correctly. No noise.
Near Austin, TX 78746
Kevin
Job Details: 05/22/2018
Arrived on site and found drain the motor is not moving water, inspected drain and found a piece of glass stopping impeller from spinning. Took one picture. Impeller is damaged and drain pump will need to be replaced. After replacing pump ran a diagnostic cycle and confirmed all operations are correct. Also found drain connection to garbage disposal is shared with reverse osmosis system. This should not be done because reverse osmosis purging could overflow dishwasher. Recommend that customer contact reverse osmosis company to correct this. Drain motor $81.02 DW165 $169.99
Near Austin, TX 78725
Joseph C.
Job Details: 05/22/2018
AMV2307PFS0 Arrived on site for “noisy fan operation” complaint. Inspected unit and found loose construction debris in fan housing. Removed debris and tested fan. Unit is performing as designed.
Near Bee Cave, TX 78738
Brandon
Job Details: 05/22/2018
Arrived on site for washer not finishing cycle, found unbalanced error code, I replaced suspension rods, unit tested good. Water lines were dry at time of service.
Near Killeen, TX 76542
Dona
Job Details: 05/22/2018
Arrived on site for burning smell and smoke, found transformer burned to magnetron and capacitor. Replaced diode, transformer, magnetron and capacitor. Verified unit working and heating correctly all ops check good. Customer helped to put microwave back up above stove.
Near New Braunfels, TX 78130
Diego G.
Job Details: 05/22/2018
Arrived on site. Replaced evaporator fan assembly. All functions tested OK. Instructed customer allow 24 hours for unit to cool down completely. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 05/22/2018
Arrived on site. Replaced evaporator fan assembly. All functions tested OK. Instructed customer allow 24 hours for unit to cool down completely. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 05/22/2018
Arrived on site. Replaced evaporator fan assembly. All functions tested OK. Instructed customer allow 24 hours for unit to cool down completely. No leaks present. Job complete
Near Jarrell, TX 76537
Steve C.
Job Details: 05/22/2018
Arrived on site for the unit right rear burner now overheating and not turning off. Found the unit was unplugged. Removed the back panel and found the right rear burner shorted. Replaced the right rear infinite switch and tested the unit. Unit heats and works properly.
Near Temple, TX 76502
Mike G.
Job Details: 05/22/2018
MMV4205AAS, Arrived on site for unit is running when not in use checked unit and found that the door switches are bad replaced switches and checked unit and unit is now working properly and heating unit checked fine at this time....
Near Temple, TX 76502
Mike G.
Job Details: 05/22/2018
MMV4205AAS, Arrived on site for unit is running when not in use checked unit and found that the door switches are bad replaced switches and checked unit and unit is now working properly and heating unit checked fine at this time....
Near Georgetown, TX 78626
Lou
Job Details: 05/21/2018
arrived on site to inspect dishwasher not working. Upon further inspection, I placed the unit in diagnostic mode and tested. The unit tested good until time to drain and the drain pump did not engage. Before I removed and replaced the drain pump, I had to vacuum the water out of the unit. In the process of removing the drain pump, I vacuumed the water from the drain pump area and a piece of glass came out of the drain pump. I checked the filter and found that it was not in place. I replaced the drain pump and reseated the filter and tested the unit. Unit operated as designed. No water leaks observed during service.
Near Austin, TX 78724
Joseph C.
Job Details: 05/21/2018
WFE530C0ES1 Arrived on site for “F9E0 error code” complaint. Inspected unit and found control faulty. Removed and replaced control. Tested unit. Unit is performing as designed.
Near Temple, TX 76502
Dona
Job Details: 05/21/2018
Arrived on site for no hot water, found unit with hot, warm, and cold water. Explained to customer auto temp control. Unit is heating to average temperature, explained cycle selection and temperatures. All water connections dry all parms check correctly.
Near Cedar Park, TX 78613
Lou
Job Details: 05/21/2018
arrived on site to inspect refrigerator dispenser not dispensing water. Upon further inspection, I found that the water filter was not seated correctly. After adjusting the filter and testing, the unit began to make a loud grinding moaning noise. I reseated the filter and tested and the unit began to operate as designed. The customer paid the service fee of $108.24 for diagnosing the problem. I quoted the customer $89.44 for the cost of the filter housing and $71.75 for labor to install the housing. These totals were without tax included. The customer opted to wait and see if the noise happened again and I advised her the quotes were good for 30 days. No water leaks observed during service.
Near Killeen, TX 76543
Dona
Job Details: 05/21/2018
Arrived on site for ice not coming out of dispenser, ice is being produced, found motor is not pushing to container correctly allowing for ice to go out of shoot. Ice bin on rear seems to be sometimes catching sometimes not will need ice bin as well. Solenoid is not always making connection. Will need to replace as well. All water connections dry. Jordan assisted with reschedule and parts.
Near Austin, TX 78722
Joseph C.
Job Details: 05/21/2018
KSGG700ESS1 Arrived on site for “burner not igniting on right front” complaint. Inspected unit and found right and left front burner caps had been switched. Switched caps back around. Unit tested good. No leaks detected, at time of service.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 05/21/2018
WDF510PAYS6 whirlpool dishwasher Arrived on site to test unit for not drying dishes and leaving them dirty. Ran diagnostic cycle to confirm operation of heater. Heater working well. Found error code f3e3 indication OWI issue. Found OWI covered in hard water and soap build up which can cause incomplete cycles due to control not being able to judge water quality. Flashing sanitize light indicates OWI failure aswell. Cleaned OWI and tested. Unit will need to be ran for an entire cycle or two to confirm repair. If issue persits please send tech out with OWI to be covered by CM. no leaks detected.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 05/21/2018
WRF989SDAM02 whirlpool refrigerator Arrived on site to test unit for ice not working. Found previous tech had removed ice box assy to clean some ice build up and facia heater for fill tube accidentally became loose and not making good contact with fill tube. Defrosted tube and corrected heater. Unit working properly, no leaks detected.
Near Austin, TX 78723
Joseph C.
Job Details: 05/21/2018
KMBS104ESS02 Arrived on site for “microwave not working properly” complaint. Inspected unit and found loose wire from capacitor to magnetron. Refitted connection. Tested unit. Unit is performing as designed.
Near Austin, TX 78733
Kevin
Job Details: 05/21/2018
Arrived on site and removed outer cabinet of washer and started each function separately manually. Inspected all wiring and components and Could not find any burning aromas described by customer. No frayed wires or dark marks on any electrical parts. Washer completed each function properly, documented findings with tech line SR7722037379
Near Austin, TX 78733
Kevin
Job Details: 05/21/2018
Arrived on site and found small amounts of frost buildup just inside a freezer door, customer has been managing frost by unplugging the refrigerator and has pictures of it being worse. Silicon both fresh food and freezer sections to ensure no air gaps between liner and outer cabinet. Also raised freezer door Approximately 1/8 of an inch to provide a better contact surface for magnetic strip. Requested that customer Monta refrigerator for correct operation and if this happens again will need service kit and a new freezer door. No water leaks from connections at time of service.
Near Austin, TX 78737
Connor M.
Job Details: 05/21/2018
WRF989SDAM02 whirlpool refrigerator Arrived on site to test unit for ice not working. Found previous tech had removed ice box assy to clean some ice build up and facia heater for fill tube accidentally became loose and not making good contact with fill tube. Defrosted tube and corrected heater. Unit working properly, no leaks detected.
Near Cedar Park, TX 78613
Lou
Job Details: 05/21/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the sump/motor and float switch. Tested unit and unit operated as designed. No water leaks observed during service.
Near Cedar Park, TX 78613
Lou
Job Details: 05/21/2018
arrived on site to inspect microwave vent hood making a noise. Upon further inspection, I could hear a slight vibration noise while the unit was on high speed. I opened the unit to inspect the mounting of the fans and found that the wiring harness was not fully tied down to its mount. I tightened the tie down and also found some of the mounting screws had backed out causing the fan to be loose. I tightened the screws and tested the unit and the unit operated as designed with no vibration noise. Job completed.
Near , TX 78617
Joseph C.
Job Details: 05/21/2018
MZF34X16DW00 Arrived on site for “freezer with intermittent cooling” complaint. Inspected unit and found control faulty. Removed and replaced control. Unit checks good. Adjusted feet for stability.
Near Pflugerville, TX 78660
Carlos G.
Job Details: 05/21/2018
Arrived onsite for customer compliant of not advancing. Checked components and found a faulty cam and actuator. Removed and replaced cam and actuator. Ran test cycle and all checks ok now. No water leaks present after service. Job complete.
Near Wimberley, TX 78676
Connor M.
Job Details: 05/21/2018
WRX735SDHZ00 whirlpool refrigerator File number-7722037759 arrived on site to test unit for rattling noise. Found when compressor runs at a certain speed it vibrates far beyond tolerance. No amount of dampening will fix this. Compressor running very hot and will eventually fail. Also fiund left freezer slide hyperextended. Ordering compressor, and slide. Sw approved friday with 2 hours.
Near Austin, TX 78731
Cliff
Job Details: 05/21/2018
Whirlpool washer WTW8700EC0. Arrived on site to diagnose a washing machine that is not cleaning properly. Tested unit and found no mechanical failures to motor drive system at this time. Did note console not beeping properly when selections are made and often cannot be reset as per owners manual instructions. Did note calcium buildup in hot water valve screen assembly but no failure to valve itself. Advised homeowner console would need to be replaced to correct no tone issue, but no other repairs are necessary at this time. Homeowner does not wish to proceed with repairs on console. No leaks were found at time of service.
Near Killeen, TX 76549
Dona
Job Details: 05/21/2018
Arrived on site for no spin, found mechanically open lid switch. Not allowing contacts for safety to allow for spin. Replaced lid switch, verified operation all ops check good. All water connections dry.
Near Dale, TX 78616
Joseph C.
Job Details: 05/21/2018
MVWC565FW0 Arrived on site for “banging noisy sound during spin cycle” complaint. Inspected unit and found gearcase coated in oil. Belt and cam coated in oil, as well. Basket is tilted to right rear. Needing suspensions, as well. Return for repairs on 05/23. No leaks detected, at time of service.
Near Austin, TX 78710
Carlos G.
Job Details: 05/21/2018
t stacked Follow standard Whirlpool processes for this repair. Exceptions include: Product Not Repairable, Contract Coverage Questions, or Customer Escalations. For these exceptions only, contact Asuri
Near Wimberley, TX 78676
Connor M.
Job Details: 05/21/2018
GHW9300PW4 whirlpool washer Arrived on site to test unit for error code f06 and stopping at beginning of cycle. Found tachometer on motor worn out. Replaced motor and tested unit. Unit working properly, no leaks detected.
Near Troy, TX 76579
Steve C.
Job Details: 05/21/2018
Near San Marcos, TX 78666
Daniel A.
Job Details: 05/21/2018
WFW8540FW1 Baffles on tub coming loose due to heater coming out of support bracket. Replaced outer tub/basket assembly. Checked suspension/water inlet/drain hoses. Ran wash cycle. Normal operation after service
Near Killeen, TX 76549
Dona
Job Details: 05/21/2018
Arrived on site for no heat, found open thermal cutoff, found ducting will need to cleaned in wall as it is preventing air flow. Replaced thermal cutoff. Verified operations. Temperatures check good.
Near Austin, TX 78731
Cliff
Job Details: 05/21/2018
Whirlpool washer WTW5000DW1. Arrived on site to diagnose a washing machine that is wrinkling clothing. Tested unit and found no mechanical failures at this time. Insured unit was fully leveled and balanced. Calibrated unit to ensure proper load sizes were registered when washing. Advised homeowner on proper loading techniques and cycles to use for best performance and to prevent unnecessarily tangling and wrinkling of clothing. No leaks found at time of service and no further repairs are needed at this time.
Near Wimberley, TX 78676
Connor M.
Job Details: 05/21/2018
WTW7040DW1 whirlpool washer Valve-152.89 TL270-159.99 arrived on site to test unit for lf error. Fiund cold water valve getting voltage but not opening. Replaced valve assy and tested unit. Unit working properly, no leaks detected. Collected balance via cc.
Near Salado, TX 76571
Dona
Job Details: 05/21/2018
Arrived on site for no cool in ff or freezer section, found aftermarket start device has been added to unit. Start device is faulty. Wires spliced to make start device work by previous company. Will need wire harness, capacitor, start device and authorization for repair. All water connections dry. Discussed with Chase. Office will reschedule.
Near Austin, TX 78725
Joseph C.
Job Details: 05/21/2018
ADB1400AGS1 Arrived on site for “door not latching” complaint. Inspected unit and found striker not engaging latch. Striker sticking straight out. Adjusted striker to mate with latch. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78745
Leonardo
Job Details: 05/21/2018
Whirlpool range model: WFC310S0ES0 no display. Arrived on site to test unit for display not showing all the number. Found bad board replaced board test unit and unit test good job complete all number working correctly.
Near Austin, TX 78745
Leonardo
Job Details: 05/21/2018
Whirlpool range model: RF365PXKW0 Arrived on site to test unit for no display on board but burner work. Test unit and found bad board replace board test unit and unit test good job complete oven and burner working correctly.
Near Salado, TX 76571
Dona
Job Details: 05/21/2018
Arrived on site for left hand door million not always closing correctly, replaced black mullion. Verified operations on door, checked temperatures all parms check good. All water connections dry.
Near Belton, TX 76513
Mike G.
Job Details: 05/19/2018
MEDX655DW1, Arrived on site for timer not working on automatic dry checked unit and found that the timer will work on timed dry with no issues and on automatic dry timer will not work unit just keeps going with out heating properly unit will need time and timer control to repair checked and cleaned out all lent found from unit ordering part and office will r/s customer
Near Belton, TX 76513
Mike G.
Job Details: 05/19/2018
MEDX655DW1, Arrived on site for timer not working on automatic dry checked unit and found that the timer will work on timed dry with no issues and on automatic dry timer will not work unit just keeps going with out heating properly unit will need time and timer control to repair checked and cleaned out all lent found from unit ordering part and office will r/s customer
Near Waco, TX 76706
Mike G.
Job Details: 05/19/2018
NED4655EW1, Arrived on site for unit not heating chcked unit and found that the vent hose from wall to unit is damaged and found that the element is shorted out replaced element and checked and cleaned out all lent found from unit and checked unit after repair and unit has good air flow with out vent hose hooked up and unit is now heating and talked to customer about replacing vent hose and not using unit until vent hose is replaced unit checked fine at this time....
Near Waco, TX 76706
Mike G.
Job Details: 05/19/2018
NED4655EW1, Arrived on site for unit not heating chcked unit and found that the vent hose from wall to unit is damaged and found that the element is shorted out replaced element and checked and cleaned out all lent found from unit and checked unit after repair and unit has good air flow with out vent hose hooked up and unit is now heating and talked to customer about replacing vent hose and not using unit until vent hose is replaced unit checked fine at this time....
Near New Braunfels, TX 78132
Connor M.
Job Details: 05/19/2018
MVWB725BW0 maytag washer Arrived on site to test unit for noise during operation. Found failed bearings. Will need call weighed. Office to schedule directly. Allow 2 hours