Near Elgin, TX 78621
Cliff
Job Details: 02/27/2019
DRYER MAYTAG MEDE300VF0 Arrived on site to diagnose a dryer that is not operating. Found main control board shorted out. Replaced control board and tested unit. Found all is functioning properly at this time.
Near Elgin, TX 78621
Cliff
Job Details: 02/27/2019
REFRIGERATOR AMANA DRS2663BW Arrived on site to replace compressor for refrigerator. While prepping unit to replace compressor noted extreme presence of corrosion on drain pan refrigerant line As well as water beating in the evaporator drain pan as well. Unit is leaking Freon and both The evaporator and drain pan heater lines will need to be replaced to correct leak. Compressor will need to be replaced as well due to contaminated system.Lastly noted 5/16 to 5/16 water connector by freezer door leaking as well. Connector will need to be replaced to correct water leak. Office will need to have repairs authorized and schedule return date for three hour job.; ordrng 1 12001940 (evaporator) and 1 12588701Q (tube) and 1 CNOTES (AUTHO NEEDED) and 1 CNOTES (3 HOUR JOB) and 1 WP2300868 (fitting)
Near Georgetown, TX 78626
Thomas L.
Job Details: 02/27/2019
OVEN WHIRLPOOL RBD275PDB6 Arrived on site or no operation. Found that the control panel fuse has failed. O; ordrng 1 WP4451042 (fuse-thrml)
Near Austin, TX 78750
Lou
Job Details: 02/27/2019
MICROWAVE WHIRLPOOL WMH31017HZ2 "arrived on site to inspect microwave not mounted properly. I found that the unit was not mounted correctly as when I opened and closed the door, the unit would move around in its place and was not level. I found that the mounting bolts were loose and not completely secured. I backed the mounting bolts out then retightened them securing the unit on the wall and leveling the unit. Unit operates as designed. Job completed."
Near New Braunfels, TX 78130
Kevin
Job Details: 02/27/2019
OVEN WHIRLPOOL RBS305PVB02 "Arrived on site and set unit to preheat and found blower fan is noisy and oven is not heating. Replaced blower fan and TOD and all function has returned to oven. Took one picture of element heating, job complete"
Near Bee Cave, TX 78738
Paul
Job Details: 02/27/2019
DRYER WHIRLPOOL WGD94HEXW0 Arrived onsite for the dryer with a water leak. I found the Y fitting leaking where the 24” hose from the house valve connects because both are corroded. The hose and the splitter need to be replaced. Ordering hose kit. RS for Wed 2/27 per ms RS for Mon 3/11.; ordrng 1 W10044609A (HOSE KIT FOR STEAM DRYER)
Near Austin, TX 78717
Lou
Job Details: 02/27/2019
MICROWAVE MAYTAG MMV1174FZ2 "arrived on site to inspect microwave installation. Upon further inspection, I found that the mo ting bolts were too short to install the unit. Customer provided longer bolts. I re-installed the unit and tested and it operated as designed. I had the customer sign a Waiver of Damages from Moving the unit as well. Job completed."
Near Temple, TX 76502
Arthur B.
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRV986FDEM01 "Arrived onsite for customer complaint of ice maker on 5 door refrigerator not dispensing ice. When arrived,found icemaker dispenses as intended. No other issues found. All water connections were dry at time of service."
Near Dale, TX 78616
Scott
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDF760SADB2 "Arrived on site for no power . Found power at junction box on tub and going to control . Also rinse aid door has broken off . Ordering control , dispenser ,autho and UI control to have on hand Incase needed . Nonwater leaks detected at time of service . Please call to set return . ; ordrng 1 AUTHO and 1 W10847890 (housing-ui) and 1 W10854220 (cntrl-elec) and 1 W10861000 (dispenser)"
Near Georgetown, TX 78633
Jonathan S
Job Details: 02/27/2019
WASHER AMANA NTW4600YQ0 "Arrived on site for washer lid light flashing. Performed diagnostics mode and checked fault codes. Found fault code F5-E2 lid lock fault. Tested lid lock lock and found mechanical failure with lock. Removed failed lock and installed new. Tested unit in automatic test cycle. Monitored test cycle. All tested good, no water leaks present."
Near Austin, TX 78734
Paul
Job Details: 02/27/2019
WASHER WHIRLPOOL WFC7500VW2 Arrived onsite for the washer to replace the previous diagnosed parts. I replaced the CCU and tested the unit. The unit reached max spin speed in the auto diagnostics test. I ran the drain/spin cycle to test the unit. The unit worked as designed. Call complete.
Near Belton, TX 76513
Steve C.
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDT970SAHZ0 Arrived on site for the unit keeps tripping the breaker. Customer advised a electrician has already replaced the breaker. Gain access to the junction box under the unit found the ground wire was not secured. Secure the ground wire and test the unit. Unit working properly and the office will call tri supply to get proof of purchase SP. All water connections were dry at time of service.
Near Austin, TX 78759
Lou
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDT970SAHZ0 "arrived on site to inspect dishwasher leaking water. I placed the unit in diagnostics and tested and removed the toe plate and found that the unit is leaking from the back right side. I pull3d the insulation up at the back right corner and found the unit dripping water from the right bottom corner of the unit. I inspected the inside of the unit and found the upper right corner of the unit was badly dented at the seem which is where the leak is coming from. I was unable to pull the unit out as one of the mounting screws was stripped and I could not get to it. I am ordering a tub, CNOTE-2 HR JOB, 2 mounting brackets and 4 screws. I scheduled return service for 02/28/19. No water leaks observed at the end of service. I advised the customer to not use the unit until after the repairs as the unit will continue to leak if used. ; ordrng 1 CNOTE (2 HR JOB) and 4 WP308685 (screw)s and 2 WP8269145 (brckt-mtg)s and 1 WPW10681506 (tub-dishwr)"
Near Waco, TX 76706
Al
Job Details: 02/27/2019
WASHER ROPER RTW4516FW2 Arrived to inspect washer not washing. Confirmed the complaint and removed and replaced the latch. Reassembled the unit and unit tested as designed.All water lines were dry at the time of service.JOB COMPLETE
Near Dale, TX 78616
Scott
Job Details: 02/27/2019
DRYER MAYTAG MEDX655DW1 "Arrived on site for long dry times .checked heater thermosats, fuses . Blower wheel . All checked good . Did find vent hose tangled and one of the leg wires on block not tightened down completely . Straightened hose and tightened terminal block wires down . No lint build up at time of service . Job complete ."
Near Austin, TX 78737
Luis
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS588FIHZ00 "Arrived on site for no ice,water dispenser issue and freezing in fresh food. Found diffuser door rubbing on housing causing door to warp and not close correctly causing fresh food to freeze. Found broken wires at wire harness to freezer door diagnosed unit will need freezer door and harness. 9/04/2018 closing date per Tiffany at partner team. ; ordrng 1 LW11037733 (FZR DOOR)"
Near Georgetown, TX 78628
James
Job Details: 02/27/2019
MICROWAVE WHIRLPOOL WMH32519HZ3 Arrived on site and inspected unit. I found that the front vent was loose. Removed and reinstalled properly. Unit tests good. Job complete
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 02/27/2019
REFRIGERATOR MAYTAG MRT118FFFE01 "Arrived onsite for customer complaint of top mount refrigerator not cooling either section. When arrived, found compressor knocking. Removed evaporator cover and found ice block on capillary tube by evaporator. Ordering compressor and air tower. Compressor is cover under 10 year warranty. R/V for Thursday 2/28. Unit unplugged at this time.; ordrng 1 CNOTE (2HR JOB) and 1 TJ90SF8404 (PROCESS STUB) and 1 W10919804 (duct-air) and 1 W11092625 (compressor) and 1 WPW10143759 (DYE DRIER)"
Near Georgetown, TX 78633
Thomas L.
Job Details: 02/27/2019
OVEN WHIRLPOOL WOS51EC0AS03 Arrived on site for a broken door glass. Found that the inner window package shattered while baking potatoes removed everyplace inner window pack
Near New Braunfels, TX 78130
Robert
Job Details: 02/27/2019
WASHER MAYTAG MVWB835DC3 "Arrived on to install console. Console installed,tested operation all operation normal."
Near New Braunfels, TX 78132
Robert
Job Details: 02/27/2019
REFRIGERATOR KITCHENAID KRFC704FBS01 Arrived on job for complaints of temperature too warm in refrigerator ran diagnostics test 57 and fan not working. Cover sent not correct.; ordrng 1 W11177683 (COVER)
Near Leander, TX 78641
James
Job Details: 02/27/2019
OVEN KITCHENAID KEBS107SSS04 Arrived on site and installed new thermal fuse. Tested unit for proper operation and found unit now heating properly. Job complete
Near Austin, TX 78735
Kevin
Job Details: 02/27/2019
DISHWASHER KITCHENAID KUDS02FSPA3 "arrived on site and inspected dishwasher and found door has lifted off of left mounting peg on tub. Re-seated door and it is now Street, level and closing properly. No water leaks from connections at time of service, job complete"
Near Belton, TX 76513
Steve C.
Job Details: 02/27/2019
WASHER MAYTAG MVWB835DW3 "On site for the unit is making noise. Customer has a video of the noise and the unit is making a loud metal scraping noise when it’s spinning. Test of the unit in diagnostics and receive no error codes. Found the unit will need a new spin basket, gear case, and will use the rotor and stater on the next visit. As well with the clutch assembly. Will need two hours to complete the repair. All water connections were dry at the time of service. Office will need to reschedule the customer.; ordrng 1 CNOTE (2HRS) and 1 W10811960 (spin basket)"
Near Burnet, TX 78611
Thomas L.
Job Details: 02/27/2019
REFRIGERATOR FRIGIDAIRE LGHB2869TF5 Arrived on site for noise condition. Found temperature in icebox compartment too high for icemaker to cycle. Found small ice piece stopping the icebox compartment fan. Removed ice operations are now normal. Our water connections were dry.
Near Paige, TX 78659
Cliff
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRF993FIFM00 Arrived on site to diagnose the refrigerator that is not cooling properly. Found a large mass of ice on RC evaporator causing unit not to get airflow through the evaporator. Defrost failures due to shortage control board. Replaced Orion control and tested unit. Found unit functioning properly at this time. No leaks were found at time of service.
Near Austin, TX 78745
Robert
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW4816FW0 Arrived on job for complaints of not always starting. Found start button not always working. Will need control board on next visit. ; saved tckt
Near Austin, TX 78726
Paul
Job Details: 02/27/2019
WASHER MAYTAG MVWX655DW1 "Arrived onsite for the washer not spinning the clothes out. I tested the washer in auto diagnostics and the unit completed the cycle and worked as designed. I tested the unit in manual and switched between agitate and high speed spin and the unit worked correctly every time. I tested the door lock multiple times in manual and it locked and unlocked correctly with no issues. I checked stored error codes and did find an F3E1, F8E1, & F8E6. I also found the leveling legs screwed all the way in the chassis. I adjusted the leveling legs out for max height. I pulled about a foot of the drain hose out of the drain pipe and tie wrapped it to secure it. I found the pressure hose in good condition. I went over detergent use and amounts with the customer and explained about cleaning the washer. There were no water leaks present at the time of service. Call complete."
Near Elgin, TX 78621
Cliff
Job Details: 02/27/2019
DRYER AMANA NED4655EW1 Arrived on site to diagnose a dryer is not heating. Tested unit and found 120 V on each leg of power but only one volt when checked together. Homeowner has a bad breaker and will need an electrician to complete the repair. No further repairs to be done by Appliance Express at this time.
Near Austin, TX 78727
Cliff
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW8900BC0 "Arrived on site to diagnose a washing machine that is spinning loudly and has a lid that is dropping abnormally. Found left side hinge broken and screw stripped out inside of hinge causing hinge not to be able to be removed from lid assembly. Also noted failed bearing in unit and lid separating due to hinge failure. Lid, hinges, and bearing will all need to be replaced to complete repairs. Others will need to have autho provided by extended warranty and set return appointment for 2 hours.; ordrng 1 CNOTES (NEEDS AUTHO AND 2 HOUR JOB.) and 1 W10842412 (lid)"
Near Georgetown, TX 78633
Jonathan S
Job Details: 02/27/2019
OVEN WHIRLPOOL WFG540H0ES1 "Arrived on site for oven temperature to hot and front left burner not igniting. Rest calibration back to 0. Performed temperature test on bake mode at 350°. Tested front burners, found cap it wrapped on both front burners and front left burner head. Replaced caps and burner and tested all burners, all tested good. Found average temperature in oven at 347°. Spoke with customer user care guide. All tested good."
Near Pflugerville, TX 78660
Steve C.
Job Details: 02/27/2019
OVEN WHIRLPOOL WOS51EC0AS04 Arrived on site for the unit is not heating properly. Tested the unit at 350° and found the actual temperature is at 320°. Calibrated the unit 30° more and the unit is working properly.
Near Austin, TX 78727
Cliff
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRF535SWHV00 Arrived on site to diagnose a refrigerator that is making unusual noises. Tested unit and found air damper running very loudly indicating damper failure. Replaced air damper and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Waco, TX 76704
Al
Job Details: 02/27/2019
DRYER ROPER RED4516FW0 "Arrived to inspect dryer not working. Checked voltage at the unit and got L1/L2 .5 L1/N OL and L2/N OL.Customer advised there is a shared 240 that runs underneath the residence. Problem is not with the dryer, it’s with the electrical outlet.JOB COMPLETE"
Near Kingsland, TX 78639
Thomas L.
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS321SDHZ01 Arrived on site for doorhandle issues. Found that the top set screw hole in the right handle was split and could not be tightened. Replaced handle. All water connections are dry.
Near Austin, TX 78741
Joseph C.
Job Details: 02/27/2019
WASHER AMANA NTW4516FW1 "Arrived on site for “noisy operation” complaint. Per my previous diagnosis, removed and replaced control, temperature selector switch, pulley shield and inlet valve. Tested and calibrated unit. Unit is performing as designed. Spoke with customer, as I could(non English speaker), about roach infestation. Tried to make her aware that further repairs will not be made in the future, if infestation is not addressed."
Near Killeen, TX 76549
Arthur B.
Job Details: 02/27/2019
DRYER WHIRLPOOL WED4815EW1 Arrived onsite for customer complaint of dryer not heating. Removed back panel to check continuity on element. Found no continuity on element and cutoff. Removed and replace element and cutoff. Reassembled. Tested unit. Unit now tumble and heats as intended. Dryer vent and lint trap was clean of lint at time of service.
Near Georgetown, TX 78626
Jonathan S
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS315SDHB00 "Arrived on site for refrigerator with low ice production. Measured temperature in FC at 3° and RC at 35°. Advanced ice maker cycle. Checked door switch to see if full engaging. Called tech support and spoke with TJ he stated unit is operating as designed (SR# 7724264277). According to tech support unit tested good, no water leaks present."
Near Austin, TX 78734
Paul
Job Details: 02/27/2019
RANGE KITCHENAID KEBC107KSS0 Arrived onsite for the oven to replace the previous diagnosed parts. I replaced the main control and the touch membrane would not respond on and button. After a few minutes the F2E1 error appeared showing the control does not recognize the keypad. I explained to the customer that the keypad was discontinued and that we could not get it. Call complete.
Near Leander, TX 78641
James
Job Details: 02/27/2019
DRYER WHIRLPOOL MED3500FW1 Arrived on site and tested operation. I found the unit heats up really fast but cools down slowly. Tested air flow at unit and found to be good. Check for air flow at exterior vents and found no air flow. Instructed customer that she would need to have the vent cleaned to outside to ensure proper air flow. Unit working as designed. Job complete
Near Georgetown, TX 78628
Lou
Job Details: 02/27/2019
OVEN WHIRLPOOL WFG525S0HS1 "arrived on site to inspect oven bottom panel. Upon further inspection, I found some damage to the center of the bottom panel. I appears that the panel paint had bubbled. Also found some black colored paint residue towards the back of the bottom panel. I removed and replaced the bottom panel and tested the unit. Operation was good. No gas leaks detected during service, job completed."
Near Killeen, TX 76549
Arthur B.
Job Details: 02/27/2019
WASHER WHIRLPOOL WFW95HEDW0 "Arrived onsite for customer complaint of front load washer not starting. Attempted to run diagnostics and found control not responding. Removed and replaced control. Reassembled and tested unit. Unit now locks,fills,washes,drain and spins as intended. No other issues found. All water connections were dry at time of service."
Near Austin, TX 78746
Robert
Job Details: 02/27/2019
DISHWASHER KITCHENAID KDTE304DSS0 Arrived on job for complaints of leaks found the sump leaks at diverter motor. Customer only wants RJ or LC for return. ; ordrng 1 WPW10455261 (pump&motor)
Near Waco, TX 76706
Al
Job Details: 02/27/2019
RANGE WHIRLPOOL WEE510S0FS2 Arrived to inspect range with variable temperatures. Confirmed the complaint and removed and replaced the oven temperature sensor. Reassembled and unit tested as designed. JOB COMPLETE.
Near Georgetown, TX 78628
Tyler B.
Job Details: 02/27/2019
OVEN WHIRLPOOL WOD97EC0HZ00 "A river back on sote for low fan speed, spoke with tl and they recommend replacing lower blower motor, replaced blower and tested good, unit heated to 350 upper and lower with no issues."
Near Austin, TX 78754
Luis
Job Details: 02/27/2019
REFRIGERATOR GE PSS26MSWASS "Arrived on site for no water. Tested dispenser no water found obstruction in water line,removed obstruction,tested water dispenser unit working as designed."
Near Austin, TX 78734
Paul
Job Details: 02/27/2019
DRYER KENMORE 110.8658111 Arrived onsite for the dryer that starts but shuts off after a couple of minutes. I found a drum roller broken and the heater burned out. Need to replace the heater and install a rebuild kit.
Near Austin, TX 78747
Leonardo
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDF331PAHS0 "Arrived on site to test unit for unit not washing. Test unit and found unit not getting any water in. Found valve turned off, opened water valve to allow water to unit and unit getting filled and wash motor coming on. Unit draining correctly no leaks present at this time Job complete"
Near , TX 78641
James
Job Details: 02/27/2019
DRYER AMANA NED4655EW1 Arrived on site and tested operation. I found the unit making a very loud growling noise and then cuts off after a few seconds. Inspected blower housing and found that the blower has come off of the motor. Reinstalled and tested only to find the same result. Unit will need new motor and blower to repair ; ordrng 1 279827 (motor!dryer) and 1 WP694089 (wheel)
Near Austin, TX 78739
Brandon
Job Details: 02/27/2019
WASHER WHIRLPOOL WFW8640bw0 "Arrived on site for customer complaint of bellow spring that fell off, I put bellow spring back on, unit tested good. Collected service fee on cc."
Near Robinson, TX 76706
Al
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW8040DW4 "Arrived to inspect washer tripping the GFCI breaker in the kitchen. Ran diagnostics on the washer and got F3E2 error code. I removed the water inlet hoses and discovered debris in the hoses. I cleared the debris and retested the unit and got NO error codes.I called whirlpool tech line and spoke with Rich, about the tripping issue. Rich advised the unit was somehow wired into the GFCI circuit and needed to be plugged into a properly grounded standard plug. (SR # 7724249151)Spoke with customer and INSTRUCTED her about the GFCI plug and advised her on a solution.Customer advised they just purchased the unit on 1/22/19."
Near Johnson City, TX 78636
Brandon
Job Details: 02/27/2019
DISHWASHER KITCHENAID KDPE334GPS0 "Arrived on site for customer complaint of fan motor staying on after unit was finished with the cycle. I replaced vent and control, unit tested good."
Near Lago Vista, TX 78645
James
Job Details: 02/27/2019
ICE MACHINE KITCHENAID KUIC18PNTS1 Arrived on site and installed new cutter grid. Tested operation and unit making ice properly. Job complete
Near Austin, TX 78744
Robert
Job Details: 02/27/2019
DRYER MAYTAG MED5500FW0 "Arrived on job for complaints of not drying. Ran diagnostics and no codes found. Heater is on and working properly. Found no air flow leaving unit, recommend customer gets vent cleaning service."
Near Georgetown, TX 78633
James
Job Details: 02/27/2019
OVEN WHIRLPOOL WFE550S0HZ0 Arrived on site and tested operation. I found light not working due to bulb has failed. Preheated oven to 400 degrees and tested temps. I found unit averaging 392. Calibrated up 10 degrees and tested and found unit averaging 402. Unit tests good. Job complete
Near Austin, TX 78744
Scott
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW4816FW2 Arrived on site disaster leaking. Ran diagnostics couldn’t duplicate leaks . No error codes . Also a Manuel fill let tub for 3/4 of ways . With console back off . No water leaks detected . No issues with drain stand during drain .all checked good on hose connections as well . Ran another test cycle . No water leaks detected . Did notice a lot of powdered soap . Tenet may be using wrong type of soap. Looked but couldn’t find soap they are using .job complete .
Near Austin, TX 78754
Luis
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS325SDHZ01 "Arrived on site for no cool in fresh food. Found freezer drain frozen over causing ice build up to block return vent. Unable to remove bottom drawer due to bucket incased in ice. Customer will need to defrost refrigerator 24 hrs with freezer door left open and towel on floor,informed customer on defrost procedure."
Near Austin, TX 78723
Cliff
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDT780SAEM1 Arrived on site to diagnose a dishwasher that is not cleaning. Tested unit and found circulation motor shorted out. Replaced pump and motor assembly. Tested unit and found all is functioning properly at this time. No leaks were found after services were performed.
Near Salado, TX 76571
Arthur B.
Job Details: 02/27/2019
REFRIGERATOR ELECTROLUX EI32AR65JS1 "Arrived onsite to install new compressor to refrigerator from my prior visit’s diagnosis. Removed faulty compressor. Installed new compressor,process stub and drier using braising methods. Vacuumed unit down to -25psi. Charged unit with 3.50oz of R134a refrigerant. Powered up unit. Saw good frost pattern beginning to form. No other issues found. No water source connected to unit at time of service."
Near Round Rock, TX 78664
Tyler B.
Job Details: 02/27/2019
WASHER GE GTW680BSJWS "Arrived on site for unit beeps not responding to buttons, found volume all the way up but no chimes, replaced control and Testd good, no leaks on site"
Near Austin, TX 78702
Scott
Job Details: 02/27/2019
RANGE KITCHENAID KFGD500ESS04 Arrived on site for range not getting gas . Arrived on site all top burners and both ovens were working . Couldn’t duplicate not working . No gas leaks detected at time of service . Job complete .
Near Austin, TX 78717
Tyler B.
Job Details: 02/27/2019
OVEN WHIRLPOOL WOS51EC0AS04 "Arrived on site for unit not heating properly, set to 350 and picked up and average of 320' removed unit, tested sensor at board and t sites within spec,,replaced control and repeated test at 350. And picked up an average of 354 , unit is now operating as designed."
Near Leander, TX 78641
James
Job Details: 02/27/2019
WASHER WHIRLPOOL MHW3505FW1 Arrived on site and found door lock light flashing and no operation from ui. Unplugged unit to attempt to reset but it would not. Set unit into diagnostics and the door unlocked. Unit ran diagnostics properly with no errors but would not start a normal cycle as the ui would shut off as soon as you hit start or within 10 seconds of waking up ui. Unplugged unit for 1 minute and plugged back in. Unit is now cycling properly and all functions test good. Job complete
Near Round Rock, TX 78665
Steve C.
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW4616FW2 Arrived on site for the unit is not spinning properly. Tested the unit and found the unit is not leveled. Level the unit in the unit is working properly. All water connections were dry at the time of service.
Near New Braunfels, TX 78130
Kevin
Job Details: 02/27/2019
DRYER WHIRLPOOL WED4815EW1 "Arrived on site and found customer was experiencing long dry times, since service call was made customer has had exhaust vent to exterior cleaned and dryer is not working properly. Airflow is good unit is heating correctly, no lint Build up in cabinet at time of service, job complete"
Near Austin, TX 78704
Luis
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRT348FMES00 Arrived on site talked to receptionist called tenant at 2303 no issues with fridge
Near Temple, TX 76502
Al
Job Details: 02/27/2019
DRYER WHIRLPOOL WED5600XW0 Arrived to inspect dryer making squeaking noise. I verified the complaint and removed and the bottom access door and reseated it into the clips. The noise went away. Customer now satisfied with the results.JOB COMPLETE.
Near New Braunfels, TX 78130
Kevin
Job Details: 02/27/2019
WASHER MAYTAG MHW5630HW0 "arrived on site and inspected washing machine and found error code for long fill, ran washer in diagnostic cycle and found water pressure on cold and hot are good. Discussed with tech line and found drain hose inserted too far into standpipe likely causing a siphon. Corrected drain hose, no water leaks from connections at time of service, job complete 7724258435"
Near Elgin, TX 78621
Cliff
Job Details: 02/27/2019
OVEN KITCHENAID KODT107ESS01 "Arrived on site to diagnose an oven that is not heating properly. Tested unit and found temperature readings through diagnostics prior to running calibration. I’ve been was only around 70° and unit was registering over 130 in diagnostics. Control panel, control board, and both oven temp sensors will need to be replaced to complete repairs. Due to part availability office will need to set return date.; ordrng 1 W10916758 (swtch-memb)"
Near Austin, TX 78727
Cliff
Job Details: 02/27/2019
REFRIGERATOR AMANA ABB1921BRM00 Arrived on site to diagnose a refrigerator that is not cooling properly. Tested unit and found refrigerator not defrosting. Defrost issue is due to failed/shorted control board. Verified functionality of defrost heater and defroster bi-metal. Replaced control and tested unit and found Alex functioning properly at this time. Homeowner will defrost unit. Advise homeowner on possible water leaks during defrost and had defrost waiver signed.
Near Waco, TX 76710
Al
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS571CIDM02 Arrived to install previously ordered part. Removed and replaced the freezer door. Reassembled and tested the unit and the water inlet valve needs to be replaced. During test I attempted to dispense water and water shot out from the valve. Rescheduled for 2/28/19 Delivery door code 9865NEEDS MORE WORK.; ordrng 1 WPW10341320 (VALVE INLET )
Near Austin, TX 78734
Paul
Job Details: 02/27/2019
DRYER MAYTAG MED6630HC0 Arrived onsite for the dryer with long dry times. Me stated she had to run multiple cycles because the unit would say the clothes were done and they were very wet. I found the dryer cycling between 136-164 degrees and keeping a 150 degree average temperature. I did find the temp very slow to drop indicating some restriction in the house vent. I advised the home owner to call the contractor because this is a new build. I also found the dryer leaning to the rear keeping the clothing from touching the sensor bars. I adjusted the level of the unit so the clothes would contact the sensor bars. The unit is working as designed. Call complete.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDT730PAHZ0 Arrived on site for no drain condition. Found that the drain pump was locked up. Replaced drain pump and tested. All water connections are dry.
Near Lago Vista, TX 78645
James
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRV986FDEM01 Arrived on site and tested operation. I found the water lines chattering while dispensing water. Replaced valves and filter head and chatter remained. I found the pressure coming in to be too high causing the chatter. Turned down pressure by closing valve and unit is now working properly. All water connections dry at time of service. Job complete
Near Austin, TX 78702
Luis
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL MBF1958XEW4 "Arrived on site for water leaking and loud clicking noise. Diagnosed frozen drain and faulty icemaker. Installed updated drain tube kit,cleared ice from drain checked water flow through drain good,installed new icemaker ran icemaker through a cycle water filled icemaker no odd noise unit working as designed. Icemaker.
Near Austin, TX 78703
Luis
Job Details: 02/27/2019
ICE MACHINE WHIRLPOOL KUID508ESS2 "Arrived on site for no ice. Ran diagnostic weak water flow,removed water valve found weak water flow from source,traced water line to external filter. Added water to reservoir ran continued diagnostics all other test passed diagnosed customer will need to replace water filter."
Near Meadowlakes, TX 78654
Thomas L.
Job Details: 02/27/2019
DISHWASHER KITCHENAID KDTM354DSS5 Arrived on site for no operation. Found failed touch panel and control board. Power in but not out.; ordrng 1 W11177740 (CONTROL) and 1 WPW10653840 (door latch)
Near Del Valle, TX 78617
Scott
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW8040DW2 "Arrived on site for wet load at end of wash. Found washer is in a shed the small board left rear foot is sitting on is breaking causing washer to lean back , enough of lean the basket is almost touching rear of cabinet .explained to husband that they need to fix the sub floor and level unit properly .ran diagnostics got off balanced load . No water leaks detected @ time of service . Job complete."
Near Kyle, TX 78640
Robert
Job Details: 02/27/2019
WASHER WHIRLPOOL MVWB865GW0 Arrived on job to drop cap. Cap dropped off.
Near Pflugerville, TX 78664
Steve C.
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS325SDHZ02 Arrived on site for the unit is leaking water. Tested the unit and found the water tube next to the filter housing is not inserted properly in the quick connect. Security connections and tested unit. Unit works properly and all water connections were dry at the time of service.
Near Belton, TX 76513
Al
Job Details: 02/27/2019
WASHER WHIRLPOOL MVWC425BW0 Arrived to inspect washer grinding. Removed the plastic cover from underneath the washer and noticed the nut was loose. Tightened the nut and tested the unit and tested as designed.No parts installed.JOB COMPLETE.
Near Round Rock, TX 78665
Tyler B.
Job Details: 02/27/2019
OVEN WHIRLPOOL WFE775H0HV "Arrived on site for door glass replacement, replaced glass and tested good."
Near Johnson City, TX 78636
Brandon
Job Details: 02/27/2019
WASHER MAYTAG MHW5500FW1 "Arrived on site for customer complaint of washer having lots of suds and door not opening and not spinning. Found F3e1 error code in diagnostic mode, found customer was using to much soap causing over sudsing. Unit tested good"
Near Taylor, TX 76574
Steve C.
Job Details: 02/27/2019
WASHER GE GTW330ASK4WW "Arrived on site for the unit belt keeps coming off. Tested the unit and found the unit will need a new motor, pulley and a new belt due to the belt keeps coming off every second wash cycle.; ordrng 1 WH01X27538 (BELT)"
Near Cedar Park, TX 78613
Lou
Job Details: 02/27/2019
WASHER WHIRLPOOL WFW95HEDW0 "arrived on site to inspect washer with water in door gasket. Upon further inspection, I placed the unit in diagnostics and it showed error codes F5E2 and F8E3. I cleared the codes and continued with testing. At the end of diagnostics, there were no error codes and the unit operated as designed. I did find a large amount of suds in the unit while testing. Advised customer to cut back on detergent use. I found that there was some water still standing in the drain area of the bellow. Using my wet vac, I got the water out ad inspected the bellow and found a large amount of debris in the drain ports of the bellow. I cleared the debris ad then inspected the drain pump and found it to be clear. I vacuumed out the inside of the pump for any debris that I could not see. Ran the unit through diagnostics again and it operated as designed with no error codes showing. No water leaks observed during service, job completed."
Near Kyle, TX 78640
Kevin
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL MDB4949SDH3 "arrived on site and set dishwasher into diagnostic cycle and found saved error F8e3, f8e2, ran a diagnostic cycle and found all functions are operating properly. Customer is experiencing cycle stopping after 5 minutes. Replaced control board and began a cycle on normal and observed it for 10 minutes. No further repair is needed at this time job complete"
Near Leander, TX 78641
James
Job Details: 02/27/2019
REFRIGERATOR KITCHENAID KORU06RSSS00 Arrived on site and tested operation. I found unit set to it’s warmest setting and the temp in unit is down to 29 degrees. I found the thermostat to be faulty. Collected diagnosis which applies to quote. ; ordrng 1 2303662 (thermostat)
Near Killeen, TX 76549
Arthur B.
Job Details: 02/27/2019
MICROWAVE KENMORE 790.8032331 Arrived onsite for customer complaint of OTR microwave fuse blown and not coming on. Removed access cover and found incorrect fuse installed. Installed proper fuse and reassembled. Powered up unit and tested. Unit now comes on. Heated 1 cup of water @ 2mins. Water was boiling with no issues. No other issues found.
Near Austin, TX 78746
Kevin
Job Details: 02/27/2019
DRYER WHIRLPOOL WGD9400SU0 arrived on site and inspected dryer and found S 22 error in the first 10 minutes of operation. Measured original thermistor resistance comparing it to a new one and it was 40% higher.Replaced thermistor and air code still pops up. Spoke with tech line and they recommended confirming harness is good and after checking they recommended replacing the control board. Remaining labor and control board will need to be collected on second visit.; ordrng 1 WPW10110641 (cntrl-elec)
Near Georgetown, TX 78633
Jonathan S
Job Details: 02/27/2019
RANGE WHIRLPOOL WFG540H0ES1 "Arrived on site for range, baking cycle not working and burner flames on cooktop are to high. Per diagnostics and tested bake mode, found spark igniter sparking but not igniter burner. Gained access to bake igniter and adjust igniter and tested. Lowed cooktop flames and tested. All tested good."
Near Austin, TX 78703
Luis
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS965CIAM01 "Arrived on site for filter housing issue. Found filter housing door unable to open. Forced housing open found housing not correctly mounted to side wall inserts,installed housing correctly to liner inserts tested door closure on housing unit working as designed installed water filter customer provided water dispensing"
Near Luling, TX 78648
Diego G.
Job Details: 02/27/2019
DISHWASHER KITCHENAID KDTM354DSS4 "Arrived on site. Checked for rack issues. Found right rail for upper rack broken. Replaced rail and cycled, all functions tested OK. No leaks present. Job complete"
Near Luling, TX 78648
Diego G.
Job Details: 02/27/2019
DISHWASHER KITCHENAID KDTM354DSS4 "Arrived on site. Checked for rack issues. Found right rail for upper rack broken. Replaced rail and cycled, all functions tested OK. No leaks present. Job complete"
Near Luling, TX 78648
Diego G.
Job Details: 02/27/2019
DISHWASHER KITCHENAID KDTM354DSS4 "Arrived on site. Checked for rack issues. Found right rail for upper rack broken. Replaced rail and cycled, all functions tested OK. No leaks present. Job complete"
Near Round Rock, TX 78665
Tyler B.
Job Details: 02/27/2019
REFRIGERATOR WHIRLPOOL WRS970CIDE01 "Arrived on site for nosiey unit, fan RF EVAP complete frosted cause fan to ice up, advised customer on defrost failures, signed waiver and will return with therm, no leaks on site ; ordrng 1 W10316760 (thermistor) and 1 W11098695 (FAN)"
Near Kingsland, TX 78639
Thomas L.
Job Details: 02/27/2019
REFRIGERATOR FRIGIDAIRE FPRU19F8RFE Arrived on site for no cool condition. Found that the unit control has failed. Replaced control and unit now starts up properly. No water is hooked up to this unit.
Near Austin, TX 78744
Robert
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW4955HW Arrived on job for complaints of not filling with water. Ran diagnostics and no codes. Washer filled to normal level. Operation of washer normal. No leaks detected at time of service.
Near Cedar Park, TX 78613
Lou
Job Details: 02/27/2019
DISHWASHER WHIRLPOOL WDF320PADS2 "arrived on site to inspect dishwasher plastic burning smell. Placed the unit in diagnostics showing no error codes. Unit operated as designed. Removed toe plate ad inspected underneath and no evidence of any burnt parts/plastic. Removed outer door panel to inspect control and dispenser and found no evidence of burnt plastic. Removed the unit from its space ad found no evidence of anything being burnt. Advised customer of my findings. No water leaks observed during service, job completed."
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 02/27/2019
DRYER MAYTAG MEDC215EW1 Arrived onsite for customer complaint of dryer not starting. Removed back panel and found proper 240V. Checked thermal fuse and found thermal fuse open. Removed and replaced thermal fuse. Reassembled and tested. Dryer now heats and tumbles as intended. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near New Braunfels, TX 78130
Kevin
Job Details: 02/27/2019
WASHER WHIRLPOOL WTW5000DW2 "Arrived on site and inspected washer and found customer is having difficulty at start of cycle, explained how correct loading procedure affects the water cycle. How much detergent is correct, how each cycle operates. Found that all functions are operating properly on washer, no water leaks from connections at time of service, job complete."