Near Bastrop, TX 78602
Carlos G.
Job Details: 01/09/2018
Arrived on site to replace parts from previous visit. Removed and replaced 4 nuts and term block. Ran test cycle and all checks ok now. Job complete.
Near Seguin, TX 78155
Connor M.
Job Details: 01/08/2018
MMV4205DS1 maytag microwave Arrived on site to test unit for not working sometimes. Found issues with both interlocks and two switches have discoloration on contacts. Will need interlocks once new ones are available. Office to order directly.
Near Bastrop, TX 78602
Carlos G.
Job Details: 01/08/2018
Arrived on site and checked the unit for not completing cycles. Ran diagnostics and found a off balance load error code. Confirmed suspension rods ok. Adjusted feet and releveled. Advised customer on proper loading. No water leaks present after service. Job complete.
Near Bastrop, TX 78602
Carlos G.
Job Details: 01/08/2018
Arrived on site to replace parts from previous visit. Removed and replaced adapter. Ran test cycle and all checks ok. No water leaks present after service. Job complete.
Near Burnet, TX 78611
Thomas L.
Job Details: 01/08/2018
Arrived on site for no ice conditions. Found slow turning module causing Fill cycle to overfill and jam injector blades and ice maker. Replaced ice maker and all water connections are dry
Near Burnet, TX 78611
Thomas L.
Job Details: 01/08/2018
Arrived on site for dryer not venting correctly. Tested all operations and all venting inside dryer is clear. All operations are normal.
Near Liberty Hill, TX 78642
Mike C.
Job Details: 01/08/2018
Amana microwave AMV2307PFS0 Arrived to find interior light not always coming on when door is opened and not starting a heating cycle. Found door switches and interlocks bad. Installed new switches and interlocks. Checked operation and unit checks good.
Near Austin, TX 78702
Carlos G.
Job Details: 01/08/2018
Arrived on site to replace parts from previous visit. Removed and replaced door switch. Ran test cycle and all checks ok now. Job complete,
Near Cedar Park, TX 78613
Jerry C.
Job Details: 01/08/2018
KICU509XBL00 Arrived to inspect loss of right side burners. The unit was flashing a service code and I inspected the module. One of the transistors was physically damaged and I removed and replaced the module. The unit worked as designed after setting to the correct mode 23. I verified original installation date by the original purchase date of the home. Operational test good.
Near Austin, TX 78721
Carlos G.
Job Details: 01/08/2018
Arrived on to replace parts from previous visit. Removed and replaced glass door. No scratches/dents on new glass door. Job complete.
Near New Braunfels, TX 78132
Connor M.
Job Details: 01/08/2018
WRS970DIDM00 whirlpool refrigerator Icemaker-101.21 149.99-labor arrived on site to test unit for not making ice. Found tray bent out of shape and not working. Replaced icemkaer and tested unit. Uunit working proeprly, no leaks detected.
Near Spicewood, TX 78669
Thomas L.
Job Details: 01/08/2018
Arrived on site for dryer that would not heat. Tested unit and found zero voltage at terminal block between L1 and L2. Instructed customer that the power condition needs to be corrected.
Near New Braunfels, TX 78132
Connor M.
Job Details: 01/08/2018
KBFO42FTX02 kitchenaid refrigerator File number-7720982232 control kit-345.62 BI150-209.99 arrived on site to test unit for not cooling. Fiund user interface would power on only for one second then die when power is pressed. Called techline and confirmed failed control. Replaced control kit and tested unit. Unit working properly. All functions accounted for. No leaks detected at time of service. Collected full balance via cc.
Near Lakeway, TX 78734
Cliff
Job Details: 01/08/2018
Maytag washer MVWX655DW1. Arrived on site to replace motor for washing machine. Replaced motor and tested unit. Found all is functioning properly at this time. Calibrated machine to ensure proper sensing. Found no water leaks at time of service.
Near Buchanan Dam, TX 78609
Thomas L.
Job Details: 01/08/2018
Arrived on site for poor washability. Found unit to have wash motor that electrically was defective. Replaced and tested and all water connections were dry.
Near Austin, TX 78732
Cliff
Job Details: 01/08/2018
Kitchenaid venthood KVUB600DSS2. Arrived on site to assist homeowner in installation of charcoal filter for vent hood. Installed charcoal filters homeowner provided at homeowners request. Tested unit and informed homeowner on timer reset functions. No other failures found at this time and all is working properly.
Near New Braunfels, TX 78132
Connor M.
Job Details: 01/08/2018
MVWX500XW2 maytag washer Arrived on site to test unit for making loud noise during wash. Found cam system had come loose and out of actuator. Corrected issue after inspecting components. Unit working proeprly, no leaks detected.
Near Wimberley, TX 78676
Connor M.
Job Details: 01/05/2018
ATW4675YQ1 admiral washer Arrived on site to test unit for thumping alot and getting off balance. Found all four suspension rods had way too much play and werent keeping tub stable. Replaced all four rods and tested unit. Unit working properly, no leaks detected.
Near Leander, TX 78641
Jerry C.
Job Details: 01/05/2018
WTW5840BW0 Arrived to inspect washer not completing cycles. I found no error codes stored within memory and the unit completed an automatic service mode test. I tested in manual mode and found excessive noise and vibration within high speed spin. The gearcase appears to be the case of the vibration, as the basket has a variance of nearly 1/2 inch when spinning. I removed the hub and turned it and retested and the area changed per the turning of the hub and basket in relation to the shaft. I quoted the customer TL280 $209.99 and gearcase $242.58. The customer needs to discuss with family and I advised them they have 30 days to accept the estimate and to have today’s service call subtracted for the total. TL100 $99.99 no leaks observed during service.
Near Wimberley, TX 78676
Connor M.
Job Details: 01/05/2018
WTW5000DW1 whirlpool washer Arrived on site to test unit for not completing cycle. Found drain pump stuck on but not moving water. Found week drain pump. Ordering for return. Office to schedule during buiness hours.
Near Wimberley, TX 78676
Connor M.
Job Details: 01/05/2018
JJW3830DS02 jennair oven Arrived on site to test unit for turning on by itself. Found error in logic. Replaced ui and tested unit. Unit working properly.
Near Kingsland, TX 78639
Thomas L.
Job Details: 01/05/2018
Arrived on site as upper rack would not Paul completely forward. Set both adjusters at the same height to unbind rack and rack now pulls forward properly. Water connections were dry.
Near Wimberley, TX 78676
Connor M.
Job Details: 01/05/2018
KFIV29PCMS02 kitchenaid refrigerator Arrived on site to test unit for frosting ini freezer. Found upper left corner liner on freezer door pulling away from door. Will need to replace door to repair. Ordering for return. Office to schedule directly.
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details: 01/05/2018
Removed and replaced seeping water valve. All operations are now normal and dry.
Near Georgetown, TX 78633
Mike C.
Job Details: 01/05/2018
Whirlpool Refrigerator WRS965CIAM01 Arrived to find unit making a popping sound coming from the diffuser. Found diffuser door broken. Installed new diffuser and checked operation, checked good. Checked unit for any leaks and none were found. Diffuser $49.14 - RF400 $159.99
Near Wimberley, TX 78676
Connor M.
Job Details: 01/05/2018
KFIS29PBMS03 kitchenaid refrigerator Arrived on site to test unit for not cooling in freezer. Found freezer at room temp, rc checked fine. Ran test 4 and confirmed coolant getting to freezer evap indicating valve is working. Checked fc thermistor at control on harness at 55 degrees. Value matched temp. Will need to replace logic board to repair. Control is covered per MS. Collecting 49.99 labor on return.
Near Round Rock, TX 78665
Chase
Job Details: 01/04/2018
WMH31017AS arrived on site to check microwave for open / close door error. Tightened Bolt interlocks and made slight adjustment to door. Was able to get microwave to function but interior light not coming on consistently. Will order the door switches and interlocks to repair unit.
Near Bastrop, TX 78602
Carlos G.
Job Details: 01/04/2018
Arrived on site to replace parts from orevious visit. Removed and replaced bearing kit and hub assembly. Ran test cycle and all checks ok. No water leaks present after service. Collected in full via CC. Job complete.
Near Austin, TX 78745
Connor M.
Job Details: 01/04/2018
WRT134TFDW00 whirlpool refrigerator Arrived on site to test unit for leaking oil onto floor. Found automatic airfreshener dispenser on top of unit leaking. No issues with fridge. Unit working properly, no leaks detected.
Near Austin, TX 78749
Connor M.
Job Details: 01/04/2018
WED4815EW1 whirlpool dryer Arrived on site to test unit for long dry cycles. Found heating element working properly. Ducting needs to be cleaned. Instruct customer on potential hazards and discontinuing use until maintenance cleans ducting.
Near Austin, TX 78749
Connor M.
Job Details: 01/04/2018
WTW4816FW2 whirlpool washer Arrived on site to test unit for leaking. Found hot water valve cracked and constantly leaking water. Replaced and tested unit unit working properly, no leaks detected.
Near Killeen, TX 76542
Arthur B.
Job Details: 01/04/2018
MVWB855DC1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not draining. Found error code F9E1 and drain pump humming. Was able to remove remaining water and remove drain pump. Found drain pump had nails lodged inside fins. Removed drain pump and installed replacement. Reassembled. Cleared error codes and ran test 052. Unit completed successfully. No other issues found. All water connections were dry at time of service.
Near Austin, TX 78750
Thomas L.
Job Details: 01/04/2018
Arrived on site to inspect unit for a water leak. All operations were normal and no water leaks were found.
Near Austin, TX 78738
Thomas L.
Job Details: 01/04/2018
Arrived on site for noisy operation during icemaker cycle. Replaced noisy inlet water valve and tested. All operations are not normal with no leaks.
Near New Braunfels, TX 78130
Daniel A.
Job Details: 01/04/2018
WTW7300DW1 Error code for locked rotor. High pitch sound during spin. Replaced drive system/rotor and clutch. Calibraypted washer. Normal operation after service. Checked water inlet and drain hoses. No leaks detected.
Near Cedar Creek, TX 78612
Carlos G.
Job Details: 01/04/2018
Arrived on site to replace part from previous visit. Removed and replaced faulty water valve. Ran test cycle and all checks ok now. No water leaks present after service. Job complete.
Near Austin, TX 78739
Connor M.
Job Details: 01/04/2018
WTW7000DW1 whirlpool washer Arrived on site to test unit for making saueaking noise during use. Found when cold water valve is turned on it chirps and squeaks for a few seconds. Will need to replace valve and housing to repair. Cs approved 1/9. Unit purchased in april 2017
Near Killeen, TX 76549
Arthur B.
Job Details: 01/04/2018
MFX2876DRM02 (4 Door French Door Refrigerator) - Arrived onsite for customer complaint of 4 Door French Door refrigerator not cooling both RC/FC sections. Ran test 04 and found good air flow in RC section. Found FC fan not running. As well. Found when is automatic mode, unit compressor will shut off. Ordering control,UI and inverter to complete repair. OF to R/S due to part availability. Customer is also requesting last call of due on R/V. All water connections were dry at time of service.
Near Austin, TX 78737
Connor M.
Job Details: 01/04/2018
WFW8300SW04 whirlpool washer File number-7720958878 arrived on site to test unit for leaving residue on light colored sheets. Found this has only happened once and is only on one part of the sheet. Unit is cleaned regularly and used gently. No evidence of residue inside unit. Called techline to confirm this issue was likely due to sheet being cuaght in door. Techline stated this is the only likely cause. No leaks detected.
Near Killeen, TX 76541
Arthur B.
Job Details: 01/04/2018
RTW4516FW1 (Top Load Washer) - Arrived onsite for customer compliant of top load washer not spinning. Ran diagnostics and found error code F0E5 (Off Balance Load). Found cabinet wobbling. Was able to level unit out by adjusting legs. Calibrated unit. Unit calibrated successfully. Tested unit. Unit fills,agitates,drain and spins with no issues. All water connections were dry at time of service.
Near Dripping Springs, TX 78620
Connor M.
Job Details: 01/04/2018
KUIX505ESS1 kitchenaid ice machine Arrived on site to test unit for not making ice and leaking. Found drain tube clogged and kinked. Will need ro replace. Ordering drain pump in case its burnt out. Will need cutter grid aswell.
Near Round Rock, TX 78681
Jerry C.
Job Details: 01/04/2018
WTW8500DC3 Arrived to inspection washer not spinning correctly. I entered service test mode and found F0E3 stored. The unit would switch between agitate and spin in manual mode, but the electro-mechanical shifter was excessively loud. I removed the rotor and found visible damage to the engagement tabs. Office to order p/n W10734521 slider, p/n W10754448 clutch and p/n W10754161 rotor. No leaks observed during service.
Near Temple, TX 76502
Arthur B.
Job Details: 01/04/2018
WRS576FIDW01 (SxS Refrigerator) - Arrived onsite for customer complaint of SxS refrigerator making loud humming noise and not cooling. Found compressor not running. Removed evaporator cover and found evaporator fan motor vibrating. Was able to adjust bracket to reduce the vibrating. Used start device WPW10197428 and capacitor WPW10350564 from compressor box. Found compressor now runs. Good frost pattern began forming. Reassembled. All water connections were dry at time of service.
Near Kyle, TX 78640
Carlos G.
Job Details: 01/04/2018
Arrived on site and checked the unit for freshfood not cooling. Found temps in FF at 50 degrees. Confirmed condenser coils are clean, evap fan working, supply and return ducts not restricted. Also verified proper frost pattern in evap coils. Found a faulty temp. control, timer, and damper. NEEDS AUTHO. Office to reschedule after getting autho.
Near Georgetown, TX 78633
Cliff
Job Details: 01/04/2018
Whirlpool refrigerator WRF535SWHZ00. Arrived on site to diagnose a refrigerator with no lights in the freezer. Found humidity control turned off causing condensation to form and drip inside the freezer. Condensation has frozen door switch in the closed position and not allowing the lights come on. Removed ice from door switch and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Austin, TX 78730
Thomas L.
Job Details: 01/04/2018
Arrived on site for improper upper rack operation. Found upper rack adjusters have failed and is causing upper rack to drop on left side. Replaced adjusters and all operations are normal and all connections are dry.
Near Austin, TX 78726
Thomas L.
Job Details: 01/04/2018
Arrived on site for PF and AF codes. Found unit will not start. Found improper voltages to unit. L2 to L1 only 124 volts L1 to NUETRAL 0 volts L2 to NEUTRAL 124 volts
Near Kyle, TX 78640
Daniel A.
Job Details: 01/03/2018
MGDX655DW2 Dryer not com8m on. Defective door switch breplaced door switch. Verified normal operation after. Instruct customer on venting/fire hazard
Near Austin, TX 78725
Carlos G.
Job Details: 01/03/2018
Arrived on site and checked the unit for not washing well. Ran diagnostics and found water temp is not hot enough and customer is using double rinse aid. Advised customer to turn up water heater as control locked out dw heater. Ran calibration cycle to reset heater. No water leaks present after service. Job complete.
Near Killeen, TX 76542
Arthur B.
Job Details: 01/03/2018
WED5100VQ0 (Dryer) - Arrived onsite for customer compliant of dryer not heating. Removed back panel and found element coils broken. Removed bulkhead and used shopvac to remove all lint build up. Removed faulty element and installed new replacement. Reassembled. Tested unit. Unit nowmheat and tumbles as intended. P&L are as follows; 279838 (Element) $69.18,DR310 $159.99 plus taxes. Dryer vent and lint trap was clean of lint at time of service.
Near Lampasas, TX 76550
Arthur B.
Job Details: 01/03/2018
MVWC360AW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer over filling. Ran diagnostics and F2E1 (Stuck Button),F8E3 (Overflow). Inspected pressure hose and blew through hose. Did find small blockage. Was able to free blockage. Calibrate unit. Unit calibrated successfully. Tested unit. Unit now fills,agitates,drain and spins as intended. All water connections were dry at time of service.
Near Leander, TX 78641
Mike C.
Job Details: 01/03/2018
Roper washer RTW4516FW Arrived to check unit for making holes in clothing. Found the water hole on the agitator has sharp edges. Installed new agitator and checked operation, checked good. Checked unit for any leaks and none were found.
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details: 01/03/2018
Arrived on site for water leaking in the dispenser area. Upon arrival this dispenser area was dry. When I dispense water it sprayed all over the place. I found that the waterline was not snapped into the water Spicket in the dispenser area properly. Corrected and tested and all operations are normal and all waterlines are dry.
Near Georgetown, TX 78628
Mike C.
Job Details: 01/03/2018
Whirlpool oven WOS51EC0AS03 Arrived and installed new control and user interface. Ohmed temp sensor and found it to read 1040 which is good. Heated unit to 350 and found cycle temps to average out to 353. Unit checks good.
Near Georgetown, TX 78633
Arthur B.
Job Details: 01/03/2018
KDTE104ESS1 (Dishwasher) - Arrived onsite for customer complaint of dishwasher leaking from bottom. Removed toe plate. Found water dripping from supply hose connected to water valve. Was able to tighten connection. Found water no longer drips. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Chase
Job Details: 01/02/2018
WRF535SMBM arrived on site to check refrigerator for no ice production. Found freezer liner warped not making full contact with light switch. Tested ice maker function by manually pressing switch and it checks good. Will order freezer door to repair unit
Near Killeen, TX 76549
Arthur B.
Job Details: 01/02/2018
MHWE201YW00 (Front Load Washer) - Arrived onsite for customer complaint of front load washer not starting and getting error code F6E1 (Communication Error). Ran diagnostics and found error code F6E1,F7E2. Tested unit. Found unit will not spin or start. Unit will need P&L; WPW10459454 (Control) $225.13, WPW10315848 (Drive Motor),FL450 $199.99 plus taxes. Drive motor is covered under 120 month part warranty. Skyped PARTS and received R/V date of 1/5 per KC. Collected SVC call fee of $108.24 today. Remaining due upon completion. All water connections were dry at time of service.
Near Round Rock, TX 78681
Thomas L.
Job Details: 01/02/2018
Arrived on site for unit not filling with hot water. Found no power from control to hot solenoid. Replaced control. Now hot solenoid is chattering. Replaced valve. All operations are normal and connections are all Arrived site for improper upper rack operation. Found failed adjusters. Replaced and now upper rack works properly. Water connections were dry.
Near Round Rock, TX 78681
Thomas L.
Job Details: 01/02/2018
Arrived on site for unit not filling with hot water. Found no power from control to hot solenoid. Replaced control. Now hot solenoid is chattering. Replaced valve. All operations are normal and connections are all Arrived site for improper upper rack operation. Found failed adjusters. Replaced and now upper rack works properly. Water connections were dry.
Near Harker Heights, TX 76548
Arthur B.
Job Details: 01/02/2018
WTW7040DW0 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not completing cycles and making loud noises when spinning. Hand spun basket and could hear gearcase grinding. Ran diagnostics and found error code F7E6 (Motor Circuit out of Phase). Ordering gearcase and stator to complete repair. Skyped PARTS and received R/V date of 1/9 per KC. All water connections were dry at time of service.
Near Leander, TX 78641
Jerry C.
Job Details: 01/02/2018
WMH32519FB0 Arrived to inspect flickering internal light. I found the unit had failed since the service call was added. I removed and replaced all switches and mounts for the door and then replaced the fuse. The unit worked as designed and heated well.
Near Round Rock, TX 78665
Thomas L.
Job Details: 01/02/2018
Arrived on site for unit not filling with hot water. Found no power from control to hot solenoid. Replaced control. Now hot solenoid is chattering. Replaced valve. All operations are normal and connections are all dry.
Near Georgetown, TX 78633
Cliff
Job Details: 01/02/2018
Maytag washer MVWC416FW0. Arrived on site to diagnose a washer that is shaking during spin. Found unit not leveled properly causing abnormal shaking during spin. Leveled unit and found all is working properly at this time. No leaks were found at time of service.
Near Austin, TX 78717
Jerry C.
Job Details: 01/01/2018
WMH73521CS5 Arrived to inspect no power and door error. I found the unit would not power up and I removed the switches and mounts and replaced them. I replaced the main fuse and tested the unit. Operational test good.
Near Nolanville, TX 76559
Arthur B.
Job Details: 01/01/2018
WDT720PADM2 (Dishwasher) - Arrived onsite for customer compliant of dishwasher not wash not washing dishes. Tested unit and found sump n motor not pumping water. Removed faulty sump n motor and installed new replacement. Reassembled. Tested unit. Unit now fills,washes,drain and heats as intended. All water connections were dry at time of service.
Near Georgetown, TX 78633
Arthur B.
Job Details: 01/01/2018
WDF730PAYM0 (Dishwasher) - Arrived onsite for customer complaint of dishwasher not cleaning dishes. Tested unit and found sump n motor not moving water. Unit will need new sump n motor. Advised customer that we must obtain authorization for part from extended warranty. Once authorization is given, OF will R/S. All water connections were dry at time of service.
Near Georgetown, TX 78633
Arthur B.
Job Details: 01/01/2018
WFG540H0ES0 (Freestanding Gas Range) - Arrived onsite for customer complaint of freestanding range knobs broken and can’t turn on burners. Found all knobs cracked. Removed knobs and replaced with new replacements. All burners now turn on easily. No other issues found. No gas leaks detected at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 12/30/2017
Arrived on site for leaking water during cycle. Tested unit and found that the air vent at the back of the tub was not tightly secured. Corrected and tested and all water connections are dry.
Near Burnet, TX 78611
Thomas L.
Job Details: 12/30/2017
Arrived on site for no operation. Found control would not enter diagnostics and open cold water solenoid. Replaced both and test. Operations are normal and dry.
Near Burnet, TX 78611
Thomas L.
Job Details: 12/30/2017
Arrived on site for no operation. Found control would not enter diagnostics and open cold water solenoid. Replaced both and test. Operations are normal and dry.
Near Georgetown, TX 78633
Thomas L.
Job Details: 12/30/2017
Arrived on site for leaking water. Found pump has crack in housing and is pushing water out under door liner. Both racks are heavily rusted. Door gasket is starting to repair. EST $350 to do motor, $120 per rack. Customer to price me units as this one is 10 years old.
Near Canyon Lake, TX 78133
Daniel A.
Job Details: 12/29/2017
WMH31017FS0 Door open/close error. Replaced upper-lower interlocks -switches. Verifiedcwiring. Normal,operation after service
Near Austin, TX 78754
Carlos G.
Job Details: 12/29/2017
Arrived on site and checked the unit for "door open" issue. Checked components and found a 3 faulty switches and top int. Removed and replaced all 3 switches and top int. Ran test cycle and all checks ok now. Job complete.
Near Killeen, TX 76542
Arthur B.
Job Details: 12/29/2017
MVWX655DW1 (Top Load Washer) - Arrived onsite for customer compliant of top load washer not completing cycles. Tested unit. Found lid latch will not lock. Removed faulty latch and installed new replacement. Reassembled. Calibrated unit. Unit calibrated successfully. No other issues found. All water connections were dry at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 12/29/2017
Near Austin, TX 78754
Carlos G.
Job Details: 12/29/2017
Arrived on site and checked the unit for not making ice issue. Checked components and found a piece of ice stuck in icemaker. Removed piece of ice. Ran diagnostics and all checks ok. No water leaks present after service. Job complete.
Near Kyle, TX 78640
Leonardo
Job Details: 12/29/2017
Whirlpool gas range WFG525S0HV0 giving F2E1 error code. Arrived on site to test unit for F2E1 error code shorted keypad. Test unit and found P11 connector had loose connection. Secured connection test unit and unit test good job complete no leaks or error codes present at this time.
Near Georgetown, TX 78633
Thomas L.
Job Details: 12/28/2017
Near Lakeway, TX 78734
Thomas L.
Job Details: 12/28/2017
Arrived on site for lose control panel. Right side screws were loose. Corrected.
Near Austin, TX 78702
Carlos G.
Job Details: 12/28/2017
Arrived on site to replace parts from previous visit. Removed and replaced heater kit and icemaker assembly. Ran test cycle and all checks ok now. No water leaks present after service. Job complete.
Near The Hills, TX 78738
Cliff
Job Details: 12/28/2017
Maytag dryer MED8200FC1. Arrived on site to diagnose a dryer that is making unusual noises when running. Found metal bracket for control board mounting was not secured from factory and was rubbing on drum. Mounted bracket properly and tested unit. Found all is functioning properly at this time.
Near Austin, TX 78754
Carlos G.
Job Details: 12/28/2017
Arrived on site and checked the unit for not cooling issue. Checked components and found a faulty control and evap thermistor. Removed and replaced both. Ran test cycle and all checks ok now. Job complete.
Near Austin, TX 78754
Carlos G.
Job Details: 12/28/2017
Arrived on site and checked the unit for not responding. Checked components and found a faulty control and UI. Removed and replaced control and UI. Ran test cycle and all checks ok. No water leaks present after service. Job complete.
Near Manor, TX 78653
Carlos G.
Job Details: 12/28/2017
Arrived on site and checked the unit for not responding. Checked components and found a faulty control and UI. Removed and replaced control and UI. Ran test cycle and all checks ok. No water leaks present after service. Job complete.
Near Georgetown, TX 78633
Mike C.
Job Details: 12/28/2017
Maytag Refrigerator MFI2269FRZ01 Arrived to check unit for no ice production. Found fill cup and fill tube frozen. Removed ice from fill tube and funnel and cycled ice maker, found motor bad on ice maker. Installed new ice maker and checked operation, checked good. Unit is in a RV and advised customer that when in storage they should turn unit off. No water leaks were found on unit.
Near Spicewood, TX 78669
Cliff
Job Details: 12/28/2017
Kitchenaid refrigerator KRMF706ESS01. Arrived on site to replace center million for refrigerator. Replaced part and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Round Rock, TX 78681
Wesley
Job Details: 12/28/2017
Fridge filter door latch needed replacement
Near , TX 78617
Carlos G.
Job Details: 12/27/2017
Arrived on site and checked the unit for noise issues. Found a faulty repair kit. Removed and replaced repair kit. Normal wear and tear. Ran test cycle and all checks ok now. Job complete.
Near Round Rock, TX 78665
Thomas L.
Job Details: 12/27/2017
Removed and replaced switches as buttons were sticking. Replaced open socket. All operations are now normal.
Near Georgetown, TX 78633
Thomas L.
Job Details: 12/26/2017
Arrived on site for no drain condition. Found drain pump was not running. Remove and replace drain pump. Unit now works properly with no water leaks.
Near Canyon Lake, TX 78133
Daniel A.
Job Details: 12/26/2017
WRS325FDAB06 Not dispensing water. Defective inlet valve. Replaced inlet valve for defective dispenser solenoid. Verified no leaks. Normal operation after service
Near Georgetown, TX 78628
Thomas L.
Job Details: 12/26/2017
Arrived on site for improper freezer door operation. I found that the upper basket in the freezer was out of time in regard to its gears in the slide sprockets. Corrected timing of upper basket and freezer door now operates properly. Water connections were dry.
Near Hutto, TX 78634
Thomas L.
Job Details: 12/26/2017
Arrived on site no heat conditions. Replaced opening fuses and dryer now operates properly. venting is clear.
Near Round Rock, TX 78664
Thomas L.
Job Details: 12/26/2017
Arrived on site for thumping and noisy operation. Found that the top supports were out of round and noisy. Replaced, tested, now normal, all venting is clear.
Near Austin, TX 78726
Chase
Job Details: 12/22/2017
KFGG500ESS Arrived on sight to check KitchenAid range for inaccurate temperatures. Found oven heating 20 degrees below set temperature. Calibrated oven temperature up 20 degrees and instructed customer on proper way to test temperature and change calibration. All checks good job complete
Near Austin, TX 78726
Chase
Job Details: 12/22/2017
KRFF305ESS0 Arrived on site. Check refrigerator for water filter stuck in housing. Was able to remove water filter, did find a plastic tab on housing broken. The tab does not affect the function of the filter, or increase chances for leak. Replaced filter for customer and customer does not want to replace the housing at this time. Job complete
Near Buda, TX 78610
Carlos G.
Job Details: 12/22/2017
Arrived on site and checked the unit for chirping noise issue. Found noise coming from gearcase, slider, clutch area. Removed and replaced gearcase, clutch, slider. Ran calibration cycle. Ran test cycle and all checks ok at this time. No water leaks present after service. Job complete.
Near Belton, TX 76513
Arthur B.
Job Details: 12/22/2017
WTW5000DW1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not starting. When arrived,found sensing light flashing. Was able to cancel control. Calibrated unit. Unit calibrated successfully. Also found open ground to unit as well. Advised customer that unit must be plugged into 3 prong receptacle. Customer will have plug changes out. No other issues found. All water connections were dry at time of service.
Near Buda, TX 78610
Carlos G.
Job Details: 12/22/2017
Arrived on site and checked the unit for spray arm melted onto element. Confirmed spray arm melted onto element. Element ok and does not need replacement. Removed and replaced melted spray arm. Job complete.
Near Temple, TX 76502
Arthur B.
Job Details: 12/22/2017
WTW8500DC3 (Top Load Washer) - Arrived onsite for customer complaint of water leaking from rear of top load washer and unit off balance. Found unit has dent on LH side of cabinet. Tested unit. Found when agitating, unit will make a clicking noise. Also found unit will not spin all full speed as well. Unit will need new gearcase,clutch,rotor and stator to complete repair. Customer is declining service at this time and speak to POS in possible exchange of the unit. No other issues found at his time. All water connections were dry at time of service.