Near Kingsland, TX 78639
Thomas L.
Job Details: 03/28/2018
Arrived on site for no ice condition. Found freezer temperature at 1°. Found icemaker has power to it. Found icemaker stall in the park position. It did have frozen ice in the mold. Replaced ice maker and new icemaker cycle properly with no water leaks.
Near Kingsland, TX 78639
Thomas L.
Job Details: 03/28/2018
Arrived on site for no ice condition. Found freezer temperature at 1°. Found icemaker has power to it. Found icemaker stall in the park position. It did have frozen ice in the mold. Replaced ice maker and new icemaker cycle properly with no water leaks.
Near Austin, TX 78723
Joseph C.
Job Details: 03/28/2018
IBS550PWS01 Arrived on site for “F1 error code” complaint. Per my previous diagnosis, removed and replaced control. Tested unit. Unit is performing as designed.
Near Austin, TX 78731
Robert
Job Details: 03/28/2018
Wfw85hefw washer Whirlpool Control.
Near Belton, TX 76513
Dona
Job Details: 03/28/2018
L1 to neutral 113volts ac. L2 to neutral 130 volts ac. Without load. Push to start engaged drops voltage to 58 volts on l1 to neutral. L2 to neutral jumps to 186 volts. Unit will run after initial depression and hold of push to start. Voltage returns to 113 volts and 130 volts. Instructed customer on improper line voltage too much variance between l1 to l2. Motor checks ok and push to start checks ok. Customer needs an electrician. Collected 108.24 on a card. Jordan helped with payment as would not process. On iPad went through. Instructed customer if double charged to call office.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 03/28/2018
Arrived on site for no light operations. And the bottom right bulb in the bottom left bulb or defective. Top left Bulb was loose and socket.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 03/28/2018
Arrived on site for no light operations. And the bottom right bulb in the bottom left bulb or defective. Top left Bulb was loose and socket.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 03/28/2018
Arrived on site for no poor condition. Found unit running and both compartments were at 66°. Compressor was running. Evacuated system, vacuumed system, recharged system. Unit held vacuum and started to Frosty evaporator. Customer to allow 24 hours to reach proper operating.
Near Leander, TX 78641
Cliff
Job Details: 03/28/2018
Kitchenaid refrigerator KRMF706ESS01. Arrived on site to replace compressor, filter dryer, right side roller, and ice bin door. Replaced all parts and Paul deep vacuum on unit. Charged unit with 6 ounces of Freon per manufacturers recommendations, and I tested unit. Found all is functioning properly at this time. No water leaks were found at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 03/28/2018
Arrived on site for no poor condition. Found unit running and both compartments were at 66°. Compressor was running. Evacuated system, vacuumed system, recharged system. Unit held vacuum and started to Frosty evaporator. Customer to allow 24 hours to reach proper operating.
Near Georgetown, TX 78628
Jonathan S
Job Details: 03/28/2018
Frigidaire dishwasher model #FDB520RHS2A. Leaking water and will not drain.
Near Jarrell, TX 76537
Dona
Job Details: 03/28/2018
Arrived on site for left front burner continually on high. Found left front infinite switch with burnt contact. Replaced infinite switch. All ops check good. All other burners check good. Temps in oven checked good.
Near Fort Hood, TX 76544
Mike G.
Job Details: 03/28/2018
MZF34X16DW00, Arrived on site for unit making noise, checked unit and found that the noise is evap fan hitting on ice unit is going into defrost ice is only around evap fan do to door being left open defrosted ice from evap fan checked unit and unit is no longer making noise checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time.... RF520 $149.99 + tax
Near Fort Hood, TX 76544
Mike G.
Job Details: 03/28/2018
MZF34X16DW00, Arrived on site for unit making noise, checked unit and found that the noise is evap fan hitting on ice unit is going into defrost ice is only around evap fan do to door being left open defrosted ice from evap fan checked unit and unit is no longer making noise checked unit for water leaks and no leaks found at time of srv.... unit checked fine at this time.... RF520 $149.99 + tax
Near Austin, TX 78703
Joseph C.
Job Details: 03/28/2018
WGD75HEFW0 Arrived on site for “dryer not heating” complaint. Per my previous diagnosis, removed and replaced ignitor. Tested unit. Unit is performing as designed. No leaks detected, at time of service. Instructed customer to clean venting every six months to prevent possible fire hazards and for better performance and economy.
Near Austin, TX 78703
Joseph C.
Job Details: 03/28/2018
Near Marble Falls, TX 78654
Thomas L.
Job Details: 03/28/2018
Arrived on site for no operation and prior poor washability. Found that the unit was in a failure mode due to a shorted dry heater. Tested unit in diagnostics, found failed soap dispenser, weak wash motor, split spray arms, and leaking inner door liner. Spray arms Pump Heater Door liner Gasket Soap dispenser 259 271
Near Jarrell, TX 76537
Dona
Job Details: 03/28/2018
Arrived on site for noise complaint, ran unit through fill, agitation, drain and spin. Found no abnormal noise. Instructed customer on normal noises of splutch changing station of motion from agitate. Unit is not hooked to hot water at this time. All water connections dry. Unit running to spec.
Near Georgetown, TX 78633
Jonathan S
Job Details: 03/28/2018
Maytag range model# MGR4452BDS. Cooktop burners flames are to big and unit is putting out smell
Near Austin, TX 78748
Brandon
Job Details: 03/28/2018
Arrived on site for dryer not turning on, found motor was not running, opened door and held down door switch and manually turned drum by hand, the motor would then turn the drum. I gained access to blower wheel, blower wheel was clear of an debris, found bad start windings on motor. I collected service fee $108.24 customer is going with repair. Vent was clear at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 03/28/2018
Arrived on site for no convection bake fan operation. Arrived on site and tested convection bake function. Found that the convection bake fan did not run. Found that the convection bake fan was defective. Replaced and re-tested operation. Operations are now correct.
Near Killeen, TX 76542
Mike G.
Job Details: 03/28/2018
WMH31017FS0, Arrived on site for unit not starting, checked unit and found that the bottom diir switch is bad replaced top and bottom interlocks and all 3 door switches and checked unit and unit is now starting and heating unit checked fine at this time.....
Near Killeen, TX 76542
Mike G.
Job Details: 03/28/2018
WMH31017FS0, Arrived on site for unit not starting, checked unit and found that the bottom diir switch is bad replaced top and bottom interlocks and all 3 door switches and checked unit and unit is now starting and heating unit checked fine at this time.....
Near Georgetown, TX 78633
Steve C.
Job Details: 03/28/2018
Arrived on site to replace the glass due to stain between the glass. Replaced the part and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Georgetown, TX 78633
Steve C.
Job Details: 03/28/2018
Arrived on site for the unit has error code f9e1 long drain. Tested the unit and found the unit will not drain. Removed the water and removed the drain catch and found clothing items. Removed the items and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Manor, TX 78653
Joseph C.
Job Details: 03/27/2018
WRT318FZDM01 Arrived on site for “freezing in fresh foods and not in the freezer” complaint. Per my previous diagnosis, removed and replaced control and all thermistors. Unit checks good. No water connected to unit.
Near Manor, TX 78653
Joseph C.
Job Details: 03/27/2018
WFG505M0BS3 Arrived on site for “stainless door trim is coming off” complaint. Per my previous diagnosis! Removed and replaced front section of oven door. Unit is performing as designed. No leaks detected, at time of service.
Near Georgetown, TX 78628
Mike C.
Job Details: 03/27/2018
Kitchen Aid dishwasher KDTM354DSS4 Arrived to check unit for poor wash performance. Put unit into diagnostics and ran a automatic diagnostics cycle and found wash motor not pumping water. Found wash motor bad. Installed new wash motor and checked operation, checked good with no water leaks.
Near Round Rock, TX 78665
Jonathan S
Job Details: 03/27/2018
Whirlpool dishwasher model# WDT750SAHZ0. Unit will not work unless pressing up against door.
Near Killeen, TX 76543
Dona
Job Details: 03/27/2018
Arrived on site for ice build up. Found unit with good frost pattern no excessive build up. Ran unit through all tests. Bi-metal checked correctly, defrost heater checked good. Checked drip pan delivery tube all clear nothing building up not allowing for flow from freezer during defrost. Temperatures in fridge are 37 degrees where customer has set. Freezer is at 3 degrees. Airflow good from freezer to fridge. All water connections dry. Unit is working to spec at this time. Defrost is set to run every 8 hours on adc.
Near Georgetown, TX 78628
Cliff
Job Details: 03/27/2018
Whirlpool dishwasher WDF330PAHS1. Arrived on site to diagnose a dishwasher with a dented panel. Found front panel dented on lower center section. Replaced panel and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Waco, TX 76712
Mike G.
Job Details: 03/27/2018
MEDC215EW1, Arrived on site formunit will not start checked unit and found that the door switch is broken replaced door switch and checked and cleaned out all lent found from unit and tested unit and unit is now starting and heating unit checkef fine at this time....,
Near Waco, TX 76712
Mike G.
Job Details: 03/27/2018
MEDC215EW1, Arrived on site formunit will not start checked unit and found that the door switch is broken replaced door switch and checked and cleaned out all lent found from unit and tested unit and unit is now starting and heating unit checkef fine at this time....,
Near Austin, TX 78739
Daniel A.
Job Details: 03/27/2018
KFCS22EVMS8 Not producing ice. Defective icemaker not advancing to harvest mode. Getting voltage. Replaced icemaker. Verified normal fill after service. Noisy damper control when energized. Replaced damper control. Defective gear motor. Normal operation after service. No air leaks detected
Near San Marcos, TX 78666
Diego G.
Job Details: 03/27/2018
Arrived on site. Replaced all controls on unit. Ran diagnostics testAnd checked all components., all functions tested OK. No leaks present. Job complete
Near San Marcos, TX 78666
Diego G.
Job Details: 03/27/2018
Arrived on site. Replaced all controls on unit. Ran diagnostics testAnd checked all components., all functions tested OK. No leaks present. Job complete
Near San Marcos, TX 78666
Diego G.
Job Details: 03/27/2018
Arrived on site. Replaced all controls on unit. Ran diagnostics testAnd checked all components., all functions tested OK. No leaks present. Job complete
Near Austin, TX 78717
Jonathan S
Job Details: 03/27/2018
Whirlpool refrigerator model # Not dispensing ice from dispenser. Arrived on site for refrigerator d
Near Austin, TX 78717
Jonathan S
Job Details: 03/27/2018
Whirlpool refrigerator model# GS5SHGXLS00
Near Killeen, TX 76543
Dona
Job Details: 03/27/2018
Arrived on site to check for resale. Ran unit dry as there are no water hookups. Unit had no save errors. Spun and drained correctly. Checked all water connections were tight and in place. Suspension on unit checks good did not go off balance. Spin speed in high no abnormal noises. all dry checks checked good.
Near Austin, TX 78731
Scott
Job Details: 03/27/2018
Arrived on site for DW not responding . Did check outlet and power cord connections to unit , both checked good . Found key pad not responding . Checked connections , did find a burn mark on UI board . Checked control , appeared to be fine . Replaced UI , unit did respond to commands . Ran diagnostics cycle , got stuck keypad error code . Unit ran diagnostics , every thing checked out normal . No water leaks detected at time of service . Job complete .
Near Austin, TX 78723
Joseph C.
Job Details: 03/27/2018
KDTE204GPS0 Arrived on site for “damaged dishwasher console” complaint. Inspected unit and found corner chipped, on console. Removed and replaced control panel. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Waco, TX 76710
Mike G.
Job Details: 03/27/2018
WTW4816FW2, Arrived on site for unit not spining out and getting off Balance, checked unit and found no error codes and recalibrated unit and ran test and unit ran all test fine talked to customer about how to load unit and how much HE soap to use checked unit for water leaks and no leaks found at time of srv..l. Unit checked fine at this time....
Near Waco, TX 76710
Mike G.
Job Details: 03/27/2018
WTW4816FW2, Arrived on site for unit not spining out and getting off Balance, checked unit and found no error codes and recalibrated unit and ran test and unit ran all test fine talked to customer about how to load unit and how much HE soap to use checked unit for water leaks and no leaks found at time of srv..l. Unit checked fine at this time....
Near Killeen, TX 76543
Dona
Job Details: 03/27/2018
Arrived on site to check for resale. Ran unit dry as there are no water hookups. Unit had no save errors. Spun and drained correctly. Checked all water connections were tight and in place. Calibrated unit all dry checks checked good.
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/27/2018
Arrived on site. Check for handle issues. Found handles not secured by installers correctly. Adjusted handle and re-secured. Also verified icemaker cycling correctly. All functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/27/2018
Arrived on site. Check for handle issues. Found handles not secured by installers correctly. Adjusted handle and re-secured. Also verified icemaker cycling correctly. All functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/27/2018
Arrived on site. Check for handle issues. Found handles not secured by installers correctly. Adjusted handle and re-secured. Also verified icemaker cycling correctly. All functions tested OK. No leaks present. Job complete
Near Cedar Park, TX 78613
Jonathan S
Job Details: 03/27/2018
Maytag dryer model #MED6000AG0. Not able to remove lint catcher.
Near Austin, TX 78744
Daniel A.
Job Details: 03/27/2018
RTW4516FW2 Lid lock not locking/unlocking. Unable to enter diagnostic. Lid lock led flashing. Replaced control. Ran automtest. Normal operation after service Checked water inlet and drain hoses. No leaks detected
Near Austin, TX 78724
Joseph C.
Job Details: 03/27/2018
WRV986FDEM01 Arrived on site for “ice forming under drawers and French door not sealing” complaint. Per my previous diagnosis, removed and replaced mullion. Cleared drain line for fresh foods defrost tray. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78724
Joseph C.
Job Details: 03/27/2018
Near Killeen, TX 76543
Dona
Job Details: 03/27/2018
Arrived on site for unit not drying clothes. Found dryer venting completely clogged off not allowing for air flow. Unit heats & tumbles removed clogged duct work. Showed customer airflow restrictions . Temperatures checked good after removing clog. Dryer vent clear.
Near Killeen, TX 76543
Dona
Job Details: 03/27/2018
Arrived on site for washer not advancing on cycle. Customer uses warm water on all loads. Found hot water hose on house side, kinked not allowing for water flow to satisfy pressure switch to move to next part of cycle. Unkinked hose, ran cycle through . Unit filled, agitated, drained and spun. No abnormal noises all water connections dry. Units water hoses are not stationary in wall they are exposed.
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/27/2018
Arrived on site. Check for draining issues. Found unit not draining water. Remove bottom panel and found loose connection at drain pump. Re-position and reconnected drain pump connector. Ran diagnostic test, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/27/2018
Arrived on site. Check for draining issues. Found unit not draining water. Remove bottom panel and found loose connection at drain pump. Re-position and reconnected drain pump connector. Ran diagnostic test, all functions tested OK. No leaks present. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/27/2018
Arrived on site. Check for draining issues. Found unit not draining water. Remove bottom panel and found loose connection at drain pump. Re-position and reconnected drain pump connector. Ran diagnostic test, all functions tested OK. No leaks present. Job complete
Near Austin, TX 78731
Scott
Job Details: 03/27/2018
Kitchenaid dish washer , dented door
Near Austin, TX 78731
Scott
Job Details: 03/27/2018
Arrived on site for steam valve dripping . Found valve leaking . Ordering valve W11179718. Return 4/3 . For now water is disconnected from dryer . Unit is free from lint at time of service . Quick pic of pop.
Near Cedar Park, TX 78613
Wesley
Job Details: 03/27/2018
Arrived on site and found unit motor shorted. Replaced motor and tested. All checks good. No leaks at time of service. Unit operating as designed.
Near Copperas Cove, TX 76522
Steve C.
Job Details: 03/27/2018
Arrived on site for the unit has error code f9e1 long drain. Tested the unit and found the unit will not drain. Removed the water and removed the drain catch and found clothing items. Removed the items and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/27/2018
KERA807PSS02 F2e1 error code for shorted touchpad. Replaced touchpad /membrane. Left front element not heating. Verified resistance on element. Replaced left front infinite switch. Not supplying voltage to element. Normal operation after service
Near Austin, TX 78724
Joseph C.
Job Details: 03/27/2018
WFG320M0BW2 Arrived on site for “black smoke being produced from oven while in use” complaint. Inspected oven and found air shutter, on burner bar completely closed. Opened shutter. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Salado, TX 76571
Dona
Job Details: 03/27/2018
Arrived on site for not all clothes drying the same. Instructed customer on usage of sensor dry and timed dry. Verified temperatures, checked drum seal. Sensors reading correctly. Dryer duct clear, good air flow. All ops checked correctly.
Near Belton, TX 76513
Dona
Job Details: 03/27/2018
Arrived on site for no spin clothes still very wet at end of cycle. Found customer stated that had unit set to mixed loads found last cycle preset with no spin speed. Showed customer how to set control re spin speed. Verified fill, agitate, rinse, and spin. All operations check correctly. All water connections dry.
Near Belton, TX 76513
Dona
Job Details: 03/27/2018
Spoke to Garret at whirlpool tech- File number 7721599592. Found door to be warped in the center allowing for air flow within freezer causing frost build up. Used sealant on prior visit to stop ambient air flow. Did not work will need door, seal and nameplate. Sarah assisted with parts. Let customer know that our office will contact them once door is in. All water connections dry.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 03/27/2018
Model WTW5000DW1, Arrived on call for washer stops after filling with water and sensing, checked for error codes and got f0 e2 over suds condition which was the only error, ran auto diag. And all checked good, then ran calabration and then ran a normal cycle and it filled with water and adjatated,as it should, then ran auto test again and then checked for error codes again and all checked good, no parts needed, instructed customer that customer instructs are not covered, this is a useing to much soap issue to were it will cancel the cycle and polarity checks good at outlet, collected service fee of 99.99 plus tax which = 108.24, also leveled the machine due to leaning to the left and down a half inch on the back, know unit is level front to back and side to side, call complete
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 03/27/2018
Model WTW5000DW1, Arrived on call for washer stops after filling with water and sensing, checked for error codes and got f0 e2 over suds condition which was the only error, ran auto diag. And all checked good, then ran calabration and then ran a normal cycle and it filled with water and adjatated,as it should, then ran auto test again and then checked for error codes again and all checked good, no parts needed, instructed customer that customer instructs are not covered, this is a useing to much soap issue to were it will cancel the cycle and polarity checks good at outlet, collected service fee of 99.99 plus tax which = 108.24, also leveled the machine due to leaning to the left and down a half inch on the back, know unit is level front to back and side to side, call complete
Near Kyle, TX 78640
Brandon
Job Details: 03/27/2018
Arrived on site for outer door panel stainless coming unglued, replaced outer door panel, unit tested good.
Near Austin, TX 78750
Cliff
Job Details: 03/27/2018
Kitchenaid dishwasher KDTE254ESS2. Arrived on site to diagnose a dishwasher with an upper rack that will not stay in position. Tested unit and found left side adjuster clip broken causing adjuster not too attach to rail. Replaced left side rack adjuster and tested unit. Found all is functioning properly at this time. No water leaks were found at time of service.
Near Kyle, TX 78640
Brandon
Job Details: 03/27/2018
Arrived on site for washing machine not draining I pulled unit out found bad drain pump power was getting to the drain pump from the control board but the pump was not activating. Ordering drain pump part number WPW10403802 water line were dry at time of service
Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
MFI2569YEM0, Arrived on site to install new water tank with filter head checked unit after repair and unit is now disp water checked unit for water leaks and no leaks found at timemof srv... unit checked fine at this time....
Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
MFI2569YEM0, Arrived on site to install new water tank with filter head checked unit after repair and unit is now disp water checked unit for water leaks and no leaks found at timemof srv... unit checked fine at this time....
Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
Near Belton, TX 76513
Mike G.
Job Details: 03/27/2018
Near New Braunfels, TX 78130
Daniel A.
Job Details: 03/26/2018
MEDB835DC3 Excessive vibration from dryer during use. Installed damper sound pads between rear panel/cabinet. Checked vent/belt/blower. Verified normal sound levels after heater energized. Instruct customer on venting/f
Near New Braunfels, TX 78130
Daniel A.
Job Details: 03/26/2018
MDB4949SDZ0 Excessive vibration/rattling from unit. Verified sump motor wash action normal sound. Drain pump impeller hitting foreign object. Removed drain pump. Checked drain hose. Ran wash cycle. Verified normal wash/action-sound level. Checked water inlet and drain hoses. No leaks detected
Near Hutto, TX 78634
Nathaniel B.
Job Details: 03/26/2018
Model WRF757SDEM01, Arrived on call for fridge light not working intermittenly, found deformed left hand door prior and not fully closing and creating moisture in ice room and compartment, installed left hand fresh food door and checked operations on door and all checked good and is know closing properly, no water leaks after repair, call complete.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 03/26/2018
Model WRF757SDEM01, Arrived on call for fridge light not working intermittenly, found deformed left hand door prior and not fully closing and creating moisture in ice room and compartment, installed left hand fresh food door and checked operations on door and all checked good and is know closing properly, no water leaks after repair, call complete.
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced terminal block. Ran oven and elements. Everything checked OK and oven reach temperature. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced terminal block. Ran oven and elements. Everything checked OK and oven reach temperature. Job complete
Near New Braunfels, TX 78130
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced terminal block. Ran oven and elements. Everything checked OK and oven reach temperature. Job complete
Near Temple, TX 76504
Dona
Job Details: 03/26/2018
Found valve mechanically open allowing for constant water to flow to icemaker. Major noise on valve. Water is in shut off position at this time so unit will not leak. All water connections are dry. Sarah assisted with reschedule and parts. Customer requested Friday 3/30.
Near Austin, TX 78727
Cliff
Job Details: 03/26/2018
Whirlpool washer WTW8040DW2. Arrived on site to diagnose a washing machine that is not completing spin cycle. Tested unit and found loose wire on clutch Molex connector causing intermittent function of clutch assembly. Rewired Molex connector properly and tested unit. Found all is now functioning properly and no water leaks were found at time of service.
Near Austin, TX 78737
Connor M.
Job Details: 03/26/2018
UMC5200BAS06 whirlpool microwave Arrived on site to test unit for not heating. Found customer had unit uninstalled and on countertop. Plugged unit in to test and found it working properly. Tested unit 3 times with wet paper towel for different lengths of time. Unable to duplicate issue. Unit working properly at time of service.
Near Temple, TX 76502
Dona
Job Details: 03/26/2018
Arrived on site for taking to long to dry, found customer needs to have household ducting cleaned. Dryer vent clear.temps checked good when not connected to house. House has restricted air flow. Found door seal starting to shred. Replaced, seal verified ops all checked good. Instructed customer to let adhesive cure before using dryer.
Near Austin, TX 78737
Connor M.
Job Details: 03/26/2018
WRF993FIFM00 whirlpool refrigerator Arrived on site to test unit for no ice and ff section too warm. Found ff evap frosted over. Will need new evap cover, control, and to return with two hours to perform full defrost along with thermistor svc pointer. Sw aporoved 3/28
Near Belton, TX 76513
Dona
Job Details: 03/26/2018
Arrived on site for no heat after self clean, found open fuse and open thermostat. Replaced both. Unit is now heating. Temperatures check good. All operations checked good.
Near Austin, TX 78727
Scott
Job Details: 03/26/2018
Arrived on site for bottom draw being blue and not SS like rest of unit . Found protective blue film still on draw . Removed film . No gas leaks detected at time of service .
Near Austin, TX 78727
Scott
Job Details: 03/26/2018
We electric range , small burner not heating
Near Buda, TX 78610
Brandon
Job Details: 03/26/2018
Arrived on site for no ice production, I put ice maker in to test found power was getting to icemaker but ice maker module is not working I replaced ice maker unit tested good all water lines were dry at time of service.
Near Austin, TX 78737
Luis
Job Details: 03/26/2018
Refrigerator-added adhesive to liner gaps
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced drain pump. Ran diagnostic test, all functions tested OK. Collect remaining balance of $300.19. No leaks present. Job complete.
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced drain pump. Ran diagnostic test, all functions tested OK. Collect remaining balance of $300.19. No leaks present. Job complete.
Near Kyle, TX 78640
Diego G.
Job Details: 03/26/2018
Arrived on site. Replaced drain pump. Ran diagnostic test, all functions tested OK. Collect remaining balance of $300.19. No leaks present. Job complete.
Near Harker Heights, TX 76548
Dona
Job Details: 03/26/2018
Arrived on site for no light in oven, found customer put factory bulb back in and unit had light. Pulled bulb and found filament hanging sometimes making contact but not always. Showed customer. Voltage checks good at bulb assy. Customer will need to replace bulb. All other ops check good.
Near Leander, TX 78645
Cliff
Job Details: 03/26/2018
Whirlpool washer WTW8000BW0. Arrived on site to diagnose a washing machine that is making a loud noises during spin. Tested unit and found all parts and components working properly but bearing in unit louder than normal. Bearing has not failed and is not causing any mechanical failures to washer at this time. Noise are not covered under home warranty policy unless caused by a failed part. No repairs to be done at this time as unit is fully functional. No leaks were found at time of service.
Near New Braunfels, TX 78132
Daniel A.
Job Details: 03/26/2018
JDB9000CWP2 Detergent dispenser not closing. Removed detergent door. Reinserted seal for dispenser. Verified normal open/closure. Checked water inlet and drain hoses. No leaks detected. Normal operation after service
Near Austin, TX 78735
Connor M.
Job Details: 03/26/2018
WED7590FW0 whirlpool dryer Arrived on site to repair unit for excessive noise. Found rear panel loose from cabinet. Corrected issue by bending panel back into place. Unit working properly. Instruct on proper venting and fire hazard.
Near Austin, TX 78735
Connor M.
Job Details: 03/26/2018
WRT541SZDM00 whirlpool refrigerator Arrived on site to test unit for frosting in freezer. Found forst build up upper left hand corner. Found corner on liner on door sparating from stainless. Will need new door. Corner cap needs replaced. Unit has already been siliconed. Office to schedule directly.