Near Temple, TX 76502
Mike G.
Job Details: 05/16/2018
WRF992FIFM00, Arrived on site to install pressure regulator on unit and tested unit after repair and unit is now disp water with no issues checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Leander, TX 78641
Lou
Job Details: 05/16/2018
arrived on site to inspect washer not turning on. Customer advised that they turned the unit on and approximately three seconds later the unit turned off and would not come back on. Customer unplugged the unit and plugged it back in and the unit came on. I ran the unit in diagnostics and the unit would shut off. I removed replaced the control me tested the unit. Unit operated as designed. No water leaks observed during service.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/16/2018
Model WFG505M0BS3, Arrived on call for interior oven light does not always work, found bad contact in light socket and has 123 ac volts to light bulb but light is still not coming on, customer to purchase new light bulb, call complete.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/16/2018
Model WFG505M0BS3, Arrived on call for interior oven light does not always work, found bad contact in light socket and has 123 ac volts to light bulb but light is still not coming on, customer to purchase new light bulb, call complete.
Near Temple, TX 76502
Dona
Job Details: 05/16/2018
Arrived on site for ice not producing in ff door section, noise in fridge. Found ice build up on rear ff evaporator, also found error BF in diagnostics showing ice bin is full. Bail arm on icemaker is showing ice box is full when it isn't. Will need to replace ff evap cover, hv control and icemaker upon return. Customer will defrost unit prior to technician return Sarah assisted with reschedule and parts. 5/21 all water connections dry.
Near Round Rock, TX 78681
Lou
Job Details: 05/15/2018
arrived on site to inspect drying not heating. Upon further inspection, I found that the element was not working. I verified ohms at the element and then found that the connection wire was badly damaged and will need to be replaced. Also found that the connector on the element was damaged as well from the wiring harness burning out. I inspected the control and found that the start button housing was broken and duct tape was being used to hold it in place. Office to order wiring harness and start device and schedule return service. I will return with pre-diagnosed parts except for the door switch.No lint observed during service.
Near Temple, TX 76502
Dona
Job Details: 05/15/2018
Arrived on site for no cool, found open start device. Start device-114.00 Capacitor on relay-81.48 Labor199.99 total is 428.10. Customer is not sure if they want to fix at this time. Have left quote. All water connections dry.
Near Temple, TX 76502
Dona
Job Details: 05/15/2018
Arrived on site for no cool, found open start device. Start device-114.00 Capacitor on relay-81.48 Labor199.99 total is 428.10. Customer is not sure if they want to fix at this time. Have left quote. All water connections dry.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 05/15/2018
Model WED4815EW1, Arrived on call for timer not advancing stuck on 40 min forever, ran cycle and ran it for 5 min and no movement from timer, installed timer, checked operation and all checks good timer is advancing, call complete.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 05/15/2018
Model WED4815EW1, Arrived on call for timer not advancing stuck on 40 min forever, ran cycle and ran it for 5 min and no movement from timer, installed timer, checked operation and all checks good timer is advancing, call complete.
Near Round Rock, TX 78681
Lou
Job Details: 05/15/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced both tracks and installed new stops. Tested unit and unit tested good. No water leaks observed during service.
Near Round Rock, TX 78681
Lou
Job Details: 05/15/2018
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/15/2018
Model WDF520PADB7 ,Arrived on call for dishes not drying, found no error codes but heater is not coming on has 123 ac volts to element but not heating amp draw on black wire at front of dishwasher was less than 2 amps when on heat cycle, being that error code did not show will use control on return and element will order it, Skyped office parts and talked to sarah and will reschedule for 5/18/18
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/15/2018
Model WDF520PADB7 ,Arrived on call for dishes not drying, found no error codes but heater is not coming on has 123 ac volts to element but not heating amp draw on black wire at front of dishwasher was less than 2 amps when on heat cycle, being that error code did not show will use control on return and element will order it, Skyped office parts and talked to sarah and will reschedule for 5/18/18
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/15/2018
Model WDF520PADB7, Arrived on call for dishes not drying, found no error codes but heater is not coming on has 123 ac volts to element but not heating amp draw on black wire at front of dishwasher was less than 2 amps when on heat cycle, being that error code did not show will use control on return and element will order it, Skyped office parts and talked to sarah and will reschedule for 5/18/18
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/15/2018
Model WDF520PADB7, Arrived on call for dishes not drying, found no error codes but heater is not coming on has 123 ac volts to element but not heating amp draw on black wire at front of dishwasher was less than 2 amps when on heat cycle, being that error code did not show will use control on return and element will order it, Skyped office parts and talked to sarah and will reschedule for 5/18/18
Near Belton, TX 76513
Dona
Job Details: 05/15/2018
Arrived on site to replace diode and capacitor that were burnt. Replaced both and verified operations 3 times. Unit is working properly and heating well.
Near Belton, TX 76513
Dona
Job Details: 05/15/2018
Arrived on site for no stop or start button working, replaced control membrane that was not making contact on that strip. Verified operations. Unit checks good.
Near Leander, TX 78641
Lou
Job Details: 05/15/2018
Arrived on site to inspect damaged legs on dryer. Upon further inspection, I found that the units feet were not properly installed and when the unit was leaned forward and backward to install the legs and when it was put into place the legs bent causing the cabinet to housing to bend. The legs were were broken inside the unit. Also, I found that the as line was not properly connected when removing to install cabinet feet. I removed and replaced the cabinet and adjusted the feet to the proper height and centered the unit. I reconnected the gas line and tested with liquid detector and found no leaks. Tested the unit and the unit operated as designed. The unit will need a vent hose clamp at the back of the unit and customer
Near Leander, TX 78641
Lou
Job Details: 05/15/2018
arrived on site to inspect range oven not working. Upon further inspection, I found that the unit control was showing F9 error code. I verified voltage in to the unit and attempted to place the unit in diagnostic mode but the control is bad. Office to order control-black and scheduled return service for 05/18/18 SW.
Near Leander, TX 78641
Lou
Job Details: 05/15/2018
arrived on site to inspect condensation and ice buildup in fc section of unit. Upon further inspection, I found that the rc door was open approximately 1/4 inch and was allowing warm air into the fc chamber. I removed the door and shelves to find ice buildup on the lower portion of the Evap cover blocking the fc door from closing/securing. There was condensation on the top, sides, and bottom of fc chamber along with some ice buildup on the bottom. I used my steamer to defrost the ice buildup and checked the Evap cover and fan and both were good. I tested both ice makers in diagnostics through code 120 and 121. Both units operated as designed. No water leaks observed during service.
Near Bastrop, TX 78602
Carlos G.
Job Details: 05/15/2018
Arrived onsite to replace parts from prior visit. Removed and replaced drum, dryer kit, element. Ran test cycle and all checks ok now. Job complete.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 05/15/2018
Model MSD2651HEW, Arrived on call for icemaker ice cubes are to large and not able to dispense ice, icemaker did not over fill so valve is not needed no ice buildup in fill tube to ice maker water in floor that froze prior was due to drain was frozen, installed icemaker , customer to dump first batch of ice and then use from then on , instructed customer ice cubes will be smaller in thickness which is normal., no water leaks at time of call, call complete.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 05/15/2018
Model MSD2651HEW, Arrived on call for icemaker ice cubes are to large and not able to dispense ice, icemaker did not over fill so valve is not needed no ice buildup in fill tube to ice maker water in floor that froze prior was due to drain was frozen, installed icemaker , customer to dump first batch of ice and then use from then on , instructed customer ice cubes will be smaller in thickness which is normal., no water leaks at time of call, call complete.
Near New Braunfels, TX 78132
Connor M.
Job Details: 05/15/2018
MED9700SB0 maytag dryer Arrived on site to install rollers for repair. Installed both rollers at rear of unit as one had fallen off completely causing other roller to deform severly. Removed excess lint caused by large gap between drum and bulkhead. Unit working properly. Instruct on proper venting and fire hazard.
Near Austin, TX 78727
Cliff
Job Details: 05/15/2018
Kitchenaid refrigerator KBFA20ERSS01. Arrived on site to diagnose a refrigerator that is not cooling properly. Found damper motor for fresh food section worn out due to normal wear and tear. Replaced damper assembly and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Killeen, TX 76542
Dona
Job Details: 05/15/2018
SR#7721997506 arrived on site for customer complaint that unit is not washing her clothing, found unit is filling to specifications, washing to specifications, unit is filling to top of washplate on normal cycle using auto sensing. On deep water wash unit is producing at least 2 inches more water depth. Checked standpipe is no more than 6 inches in wall. Watched agitation with clothing washplate is moving clothing from top to bottom as designed. No error codes. Unit is filling at correct timing and depth. All water connections dry. Customer is unsatisfied with operations of machine. Customer started using excessive language, hitting walls with her fist, customer opened door, tech turned machine off and left home.
Near Georgetown, TX 78626
Mike C.
Job Details: 05/15/2018
Kitchen Aid dishwasher KDTE104DSS0 Arrived to find door not closing. Found the left hinge had come out of the hinge pin. Reset hinge onto pin and checked operation, checked good with no water leaks. DW380 $199.99
Near Austin, TX 78723
Joseph C.
Job Details: 05/15/2018
WTW7000DW0 Arrived on site for “hole in agitator and clothing is getting stuck” complaint. Inspected unit and found hole in washplate. Hot water was turned off. Hot water being off generated an F08E02 error code. Turned on hot water and removed and replaced washplate. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near New Braunfels, TX 78132
Connor M.
Job Details: 05/15/2018
WRX988SIBM00 whirlpool refrigerator Arrived on site to install parts for return. Installed adapter kit, and sealed fill tube opening at back of unit. Unit working properly, no leaks detected.
Near Georgetown, TX 78628
Mike C.
Job Details: 05/15/2018
Kitchen Aid Refrigerator KSSC48QTS02 Arrived and installed new ice door motor and door. Checked operation and unit checks good with no water leaks.
Near New Braunfels, TX 78132
Connor M.
Job Details: 05/15/2018
WRF767SDEM01 whirlpool refrigerator Arrived on site to test unit for temps too high in ff compartment. Fiund evap severly frosted over. Will need to defrost for 24 hours before repair to avoid damaging evap. Sw approved 5/17. Will need to replace harness and perform proper service pointer.
Near Austin, TX 78723
Joseph C.
Job Details: 05/15/2018
WFW92HEFC0 Arrived on site for “F08E02 error code” complaint. Inspected unit and found expansion board and dispenser motor to be faulty. Removed and replaced board and motor. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Lampasas, TX 76550
Dona
Job Details: 05/15/2018
Arrived on site for no ice production, previous tech replaced control that had burned and taken out ice maker and dispenser, replaced ice maker, verified unit is filling and starting ice production, all water connections dry.
Near New Braunfels, TX 78132
Connor M.
Job Details: 05/15/2018
WDT920SADM3 whirlpool dishwasher Arrived on site to test unit for not drying dishes well. Found rinse aid dispenser has never been used. Confirmed heater operation and instruct on proper use. No leaks detected.
Near Austin, TX 78737
Brandon
Job Details: 05/15/2018
Arrived on site for unit not heating, I found bad element, I replaced heating element unit tested good. Vent was clear at time of service.
Near Bee Cave, TX 78738
Kevin
Job Details: 05/15/2018
Dryer is stacked on top of washer, floor is also made of decking and is uneven. Arrived on site and set washer into diagnostic cycle and found saved code F9 E2, ran a diagnostic cycle and all functions progressed properly. Removed lower panel and found debris in drain catch, after reassembling ran a diagnostic cycle again and all functions still operating properly. Could not duplicate cause of error code but if situation happens Again will need to bring back main harness, control board, and drain pump. No leaks from connections at time of service, job complete
Near New Braunfels, TX 78130
Connor M.
Job Details: 05/15/2018
UXT4030ADB2 whirlpool vent hood Arrived on site to test unit for not moving air when turned on. Found fan not reaching proper speeds with correct voltage. Replaced fan and tested unit. Unit working properly.
Near New Braunfels, TX 78130
Connor M.
Job Details: 05/15/2018
MDB8959SFZ4 maytag washer Arri ed on site to test unit for leaking during use. Found condensation on top outsid eof unit, pink residue all over unit. No components leaking. Unable to duplicate issue. Water is most apparent on left side. Ordering gasket and left hinge. Customer needs 12-3 on thursday. If unable to schedule properly please contact customer.
Near Round Rock, TX 78681
Cliff
Job Details: 05/15/2018
Whirlpool refrigerator GI5FSAXVY01. Arrived on site to replace start device for refrigerator compressor. Replaced part and tested unit. Found all is functioning properly at this time. Unit was not hooked up to water at time of service.
Near Temple, TX 76502
Dona
Job Details: 05/15/2018
Arrived on site to replace valve and recirculating pump, found recirculating pump motor with excessive noise. Found valve mechanically closed not allowing for water flow. Verified no noise and ice production starting. Once unit was pulled out to remove power and turn water off, technician noticed the house side incoming water on valve is dripping. Took pictures. Customer will need to get a plumber to change fitting or tighten. Showed customer where dripping. Left unit pulled out with towel underneath so that unit is not dripping on floor. Fitting is dripping heavily when unit is in off position. Darker spots on left cabinet interior on house took pictures. All water connections on unit are dry. Sold cleaner collected 26.42 on card.
Near Dripping Springs, TX 78620
Brandon
Job Details: 05/15/2018
Arrived on site for part hanger I replaced dispenser, unit tested good. Water lines were dry at time of service.
Near Georgetown, TX 78628
Lou
Job Details: 05/15/2018
Near New Braunfels, TX 78130
Connor M.
Job Details: 05/15/2018
WFW3090GW whirlpool washer Installed tank and tested unit. Unit working properly, no leaks detected.
Near New Braunfels, TX 78130
Connor M.
Job Details: 05/15/2018
WTW8540BW whirlpool washer Arrived on site to install bearing kit and rotor. Installed both parts and tested unit. Unit working properly, no leaks detected.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 05/15/2018
Model MMV4206FZ2, Arrived on call for microwave not heating, installed cap, mag, diode, and checked operation and all checks good, call complete.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 05/15/2018
Model MMV4206FZ2, Arrived on call for microwave not heating, installed cap, mag, diode, and checked operation and all checks good, call complete.
Near Kyle, TX 78640
Brandon
Job Details: 05/15/2018
Arrived on site for unit not unlocking, found bad door latch, I replaced the door latch, unit tested good.
Near Temple, TX 76501
Dona
Job Details: 05/15/2018
Arrived on site for deep fill issues, found unit is filling correctly on predetermined settings. Normal cycle, clean washer, sanitize nor drain and spin will allow deep water pre determined from factory. Verified correct fill amounts, verified wash, drain and spin with clothing. All parms check correctly. All water connections dry.
Near Lorena, TX 76655
Mike G.
Job Details: 05/15/2018
WDT720PADM0, Arrived on site for unit not draining checked unit and found that the drain pump is not turning on replaced drain pump and retested unit and found that the unit is not draining checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Lorena, TX 76655
Mike G.
Job Details: 05/15/2018
WDT720PADM0, Arrived on site for unit not draining checked unit and found that the drain pump is not turning on replaced drain pump and retested unit and found that the unit is not draining checked unit for water leaks and no leaks found at time of srv... unit checked fine at this time....
Near Kyle, TX 78640
Brandon
Job Details: 05/15/2018
Arrived on site for part hanger, I replaced the control and overlay, unit tested good.
Near Taylor, TX 76574
Nathaniel B.
Job Details: 05/14/2018
Model WTW6800WW1, Unit has a 1 year extended warranty through the builder, unit was put in to home by builder when customer moved in the home, dusty turner from kb homes 512-809-1248, found unit has a f2 key pad which is a user interface failure, replaced user interface and then went to test with f2 error gone and found unit trying to lock and unlock 3 times on its own and will not start cycle then replaced main control and know is showing a du error which is a lid lock failure, will need to order lid lock, office will reschedule with customer.
Near Taylor, TX 76574
Nathaniel B.
Job Details: 05/14/2018
Model WTW6800WW1, Unit has a 1 year extended warranty through the builder, unit was put in to home by builder when customer moved in the home, dusty turner from kb homes 512-809-1248, found unit has a f2 key pad which is a user interface failure, replaced user interface and then went to test with f2 error gone and found unit trying to lock and unlock 3 times on its own and will not start cycle then replaced main control and know is showing a du error which is a lid lock failure, will need to order lid lock, office will reschedule with customer.
Near Austin, TX 78717
Lou
Job Details: 05/14/2018
arrived on site to inspect gas leak from front left burner on cooktop. Upon further inspection, I tested all gas connections under the unit with liquid detector and found no leaks. Customer provided a copy of a receipt from the gas company which their notes stated there is a gas leak on the front left burner. I removed the cooktop and tested all connections to the burners and valves and found no leaks. The customer was not home but his adult son was and I verified the test with him by showing him there were no leaks using the liquid detector. I spoke to the customer on the phone and he said his wife was having a difficult time getting the left burner to come on. I removed and replaced the left front burner valve and tested and it tested good. It appears that when the customer uses the unit, they are not turning the knob to ignite soon enough allowing gas to escape the burner before igniting causing what appears to be a gas leak. I showed the customers son how the unit operates so he co
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/14/2018
Model MSD2542VEW00, Arrived on call for no cool complaint, replaced compressor and valve and dye drier and pulled vacuum for 20 min and held for 15 min and charged system with 5.00 oz and compressor amp draw is 1.3 amps and dropping and is getting good heat exchange and temp is dropping in freezer and low side pressure is +1 which is good, customer to allow the unit to run for 24-48 hours for proper cooling, unit is not connected to water, call complete.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/14/2018
Model MSD2542VEW00, Arrived on call for no cool complaint, replaced compressor and valve and dye drier and pulled vacuum for 20 min and held for 15 min and charged system with 5.00 oz and compressor amp draw is 1.3 amps and dropping and is getting good heat exchange and temp is dropping in freezer and low side pressure is +1 which is good, customer to allow the unit to run for 24-48 hours for proper cooling, unit is not connected to water, call complete.
Near Cedar Park, TX 78613
Jerry C.
Job Details: 05/14/2018
GX5FHDXVD00 Arrived to inspect cooling issue. I found the sealed system and condenser fan running, but there was not evaporator fan operation. I verified line voltage to the fan that then removed and replaced it. I tested the unit and it had all functions present. Operational test good, no leaks observed during service.
Near Killeen, TX 76542
Dona
Job Details: 05/14/2018
Arrived on site for no operation, found push to start was stuck in off position, removed console and removed front control and was able to free start button into unstuck position. Tried unit 7 x and unit is working correctly now.
Near Austin, TX 78737
Luis
Job Details: 05/14/2018
Refrigerator-adjusted freezer door fixed filter head
Near Round Rock, TX 78665
Jonathan S
Job Details: 05/14/2018
Whirlpool range model #WFG515S0ES1. Not maintaining correct temperature.
Near Cedar Park, TX 78613
Lou
Job Details: 05/14/2018
arrive on site to install previously diagnosed and ordered parts. The customer had defrosted the unit prior to my return and actually turned the unit back on. The unit appeared to be working as designed with no ice buildup. I removed and replaced the Evap cover, Evap motor, and support. Tested the unit and the tested good. No water leaks observed during service. Job completed.
Near Copperas Cove, TX 76522
Dona
Job Details: 05/14/2018
Arrived on site for no ice production, found motor is stalling on ice maker, jumpered across to bypass for valve. Will bring valve on return visit. Will need ice maker May need valve. All water connections dry. Jordan assisted with reschedule and parts.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/14/2018
Model KDTE254ESS1, Autho. KEFUEEFEPL1, arrived on call for dispenser cracked and key pad has some functions not responding and led for main control not lighting and tine row rusting, installed all parts that previous tech ordered and ran all functions and no error codes, all checks good, call complete, no water leaks at time of call. Also instructed customer on soap and rinse aid use and to go away from pack soaps, go to liquid 1 table spoon to 1 tea spoon and rinse aid set to 1, call complete.
Near Round Rock, TX 78665
Nathaniel B.
Job Details: 05/14/2018
Model KDTE254ESS1, Autho. KEFUEEFEPL1, arrived on call for dispenser cracked and key pad has some functions not responding and led for main control not lighting and tine row rusting, installed all parts that previous tech ordered and ran all functions and no error codes, all checks good, call complete, no water leaks at time of call. Also instructed customer on soap and rinse aid use and to go away from pack soaps, go to liquid 1 table spoon to 1 tea spoon and rinse aid set to 1, call complete.
Near Copperas Cove, TX 76522
Dona
Job Details: 05/14/2018
Arrived on site for no heated dry, found element is burned near the front of element, will need to replace element, Jordan assisted with parts and reschedule of 5/16/18. All water connections dry.
Near Cedar Park, TX 78613
Lou
Job Details: 05/14/2018
arrived on site to inspect washer that flooded house. Upon further inspection, I tested diagnostic mode and the unit tested good with no error codes. Customer advised that she was out of town for approximately ten days and she left the washer door open about half way to allow it to dry inside. Upon her return, she found a large amount of water on the floor and inside the unit. She advised that she has used the unit since with no issues. I quoted the customer $96.38 for inlet valve and FL340 $189.99 for service fee and labor. Total with tax was $310.00. Customer agreed to service and paid fees. Office to order inlet valve and schedule return service.
Near Austin, TX 78757
Cliff
Job Details: 05/14/2018
Kitchenaid dishwasher KDTE104DSS0. Arrived on site to diagnose a dishwasher that is not cleaning properly. Tested unit and found F7 E1 error code saved in control from previous malfunction on unit. Reset all error codes through diagnostic and tested system. Found all is fully functional at this time and heating system is working properly. As error codes should have been reset during last service visit there are no charges for homeowner at this time. All is working properly and there were no leaks found at time of service.
Near Austin, TX 78738
Luis
Job Details: 05/14/2018
Refrigerator-replaced damaged fresh food door
Near Austin, TX 78754
Joseph C.
Job Details: 05/14/2018
JDB9600CWP0 Arrived on site for “rework # R11253” complaint. Per rework order, removed and replaced power cord with Kit # W11188410. Tested unit. No leaks detected, at time of service.
Near Austin, TX 78703
Connor M.
Job Details: 05/14/2018
WFW9351YW00 whirlpool washer Valve-80.93 fl340-169.99 arrived on site to test unit for water remaining in tub after cycle and accumulating when not in use. Found error code for no fill/ long fill. Diagnosed bad water valve. Ordering for return. Sw approved 5/17
Near Killeen, TX 76549
Dona
Job Details: 05/14/2018
Replaced defrost control and bimetal, verified frost pattern good. Back evaporator panel was off on tech arrival as well as shelving. Previous tech had customer do a self defrost on unit. Screws missing from back Panel. Tech reinstalled with extra screws on hand. All water connections dry. Instructed customer not to load unit for 24 hours until unit fully cools. All parms check ok.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 05/14/2018
Model NED4655EW1, Arrived on call for unit will not cut off and dryer is not heating, found dryer timer had power to it but not advancing, replaced timer, then found unit not heating and found loosing voltage to heat cycle due to bad contact in outlet and also dryer wall vent is restricted , customer to contact apartments office and they will need to contact a electrician to have outlet replaced and dryer wall vent cleared, instructed customer not to run dryer until wall vent is cleared due to this is a fire hazard, call complete.
Near Round Rock, TX 78664
Nathaniel B.
Job Details: 05/14/2018
Model NED4655EW1, Arrived on call for unit will not cut off and dryer is not heating, found dryer timer had power to it but not advancing, replaced timer, then found unit not heating and found loosing voltage to heat cycle due to bad contact in outlet and also dryer wall vent is restricted , customer to contact apartments office and they will need to contact a electrician to have outlet replaced and dryer wall vent cleared, instructed customer not to run dryer until wall vent is cleared due to this is a fire hazard, call complete.
Near Leander, TX 78641
Jerry C.
Job Details: 05/14/2018
WFE515S0ES0 Arrived to inspect temperature issue. I tested at 350 with a starting temperature of 74 degrees. The unit claimed preheat at 370. The unit cooled to 330 and then heated to 390. The unit averaged at 360 degrees. I induced a -10 degree offset and advised the customer. Operational test good.
Near Austin, TX 78703
Connor M.
Job Details: 05/14/2018
WTW4800XQ4 whirlpool washer Arrived on site to install gearcase for repair. Installed gearcase and tested unit.munit working properly at time of service. No leaks detected.
Near , TX 78617
Carlos G.
Job Details: 05/14/2018
Arrived on call for washer will not adjitate or start cycle, checked for error codes and found no error codes, then ran auto test and all checked good, then ran unit with a full size load which is 5-6 pairs of jeans and tested and all checks good, recalabrated the control and instructed customer to run as normal and if issue repeats to take a video recording, no water leaks at time of call, call complete, no parts needed at this time not able to verify same symptom customer was having and there was no stored error codes.
Near , TX 78617
Carlos G.
Job Details: 05/14/2018
here 4/18 WED, 10:06 to 10:34, Arrived on call for shaking badly during spin cycle, found customer did not take video record as instructed prior, checked for error codes as i did before and no error codes then ran a drain and spin and found a little wabble and right hand side is down more than the left hand side of the machine, did level the unit prior and has dropped down again, floor is weak, instructed customer to put a piece of plywood under the machine to keep floor from sinking when unit goes in to spin in high speed, releveled unit and ran drain and spin again and all checks good, customer to put a full sheet of plywood under the machine the with front to back and side to side of the machine to keep floor from
Near Killeen, TX 76549
Dona
Job Details: 05/14/2018
Arrived on site for no ice, found ice pad stuck and would not depress to allow for ice to dispense. Adjusted pad on ice side is now depressing allowing for ice to dispense. Temperatures check correct in fridge and freezer. Unit is producing ice, ice bucket is full. All water connections dry.
Near Leander, TX 78641
Lou
Job Details: 05/14/2018
Arrived on site to inspect dishwasher not getting dishes dry or clean. Upon further inspection, I placed the unit in diagnostic mode and tested. Unit operated as designed. I did find that the lower spray arm is sagging causing it to get caught on their heating element. The customer advised that she is filling the detergent dispenser completely full. I advised that the she should only fill approximately half way. Also advised the customer to leave the door cracked open after cycle is complete to allow airflow inside the unit to help with drying due to the unit having a plastic tube and does not dry well. Office to order lower spray arm and schedule return service for 05/15/18 MS. No water leaks observed during service.
Near Leander, TX 78641
Lou
Job Details: 05/14/2018
Near Austin, TX 78733
Luis
Job Details: 05/14/2018
Refrigerator-replaced broken water and ice paddles
Near Austin, TX 78758
Cliff
Job Details: 05/14/2018
Whirlpool dishwasher WDT720PADW2. Arrived on site to diagnose a dishwasher with a door that is opening too quickly. Tested unit and found friction pads for both door springs broken causing less than normal door resistance. Replaced both friction pads and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Manor, TX 78653
Joseph C.
Job Details: 05/14/2018
MDBD820AWB Arrived on site for “smoke coming from unit” complaint. Per previous diagnosis, removed and replaced element and o-rings. Tested unit. No leaks detected, at time of service.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 05/14/2018
Model WFG515S0EB1, Arrived on call for right front burner and left front burner sometimes not lighting gas, found both igniters are igniting, found issue is with caps and or right front and left front burners not allowing gas to ignite, will order burner caps and right front and left front burners, skyped office parts and no answer, office will reschedule with customer. No gas leaks at time of call
Near Hutto, TX 78634
Nathaniel B.
Job Details: 05/14/2018
Model WFG515S0EB1, Arrived on call for right front burner and left front burner sometimes not lighting gas, found both igniters are igniting, found issue is with caps and or right front and left front burners not allowing gas to ignite, will order burner caps and right front and left front burners, skyped office parts and no answer, office will reschedule with customer. No gas leaks at time of call
Near Hutto, TX 78634
Nathaniel B.
Job Details: 05/14/2018
Model WDF520PADB7, Arrived on call for front right stop coming off, replaced right front stop and tested and is locked on rail whl not needed, all checks good, call complete. No water leaks at time of call.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 05/14/2018
Model WDF520PADB7, Arrived on call for front right stop coming off, replaced right front stop and tested and is locked on rail whl not needed, all checks good, call complete. No water leaks at time of call.
Near Austin, TX 78732
Paul
Job Details: 05/14/2018
Maytag Dryer Model MEDX655DW1. Arrived onsite for the dryer that has long dry times and is making a thumping noise. I found the dryer leaning forward not allowing the clothing to come in contact with the sensors at the rear of the drum correctly. I found the RF leveling leg not touching the floor. I adjusted the level of the dryer to correct this. I found the drum temperature averaging 154 degrees and the unit working as designed. Call complete.
Near Austin, TX 78758
Cliff
Job Details: 05/14/2018
Amana washer NTW4516FW1. Arrived on site to diagnose a washing machine that is not filling with water. Tested unit and found calcium in valve has caused a clog in the waterline preventing unit from getting water. Cleared all debris’s from valve but due to water main break at apartments there’s no water to the unit at this time for testing purposes. Advised customer that waterlines will need to be flushed prior to attaching hoses to the valve on the unit. Was not able to test for leaks today but washer should operate properly once water is restored.
Near Austin, TX 78701
Connor M.
Job Details: 05/14/2018
WED9550WW1 whirlpool dryer Arrived on site to test unit for noise during operation and long dry cycles. Found dyrer duct in rear of unit restircted causing poor airflow. Instruct on having duct replaced or repaired. Squeaking noise cuaed by idler pullet seizing up. Replaced idler pulley, rollers and belt. Unit working properly. Instruct on proper venting and fire hazard.
Near Austin, TX 78746
Luis
Job Details: 05/14/2018
Ice machine-replaced failed water valve
Near Nolanville, TX 76559
Dona
Job Details: 05/14/2018
Arrived on site for no operation with f01 error, found correct household voltage, found faulty main motor control. Replaced control, verified operations, unit checked good. Dryer venting is clear.
Near Nolanville, TX 76559
Dona
Job Details: 05/14/2018
Arrived on site for no cool in freezer. Found upon arrival freezer is at 2 degrees, found frost build up on interior, left side of freezer door seal is sagging. Will need to replace door seal. Customer states that freezer was not cooling major noise in freezer and that all food thawed out as well. Will need to replace thermostat included in freezer evaporator motor on freezer. No ice build up in fridge, will bring on return visit no ice build up on evaporators. All water connections dry. Callie assisted with part and reschedule date.
Near Austin, TX 78753
Carlos G.
Job Details: 05/14/2018
/16/18 9:22: SM there 3/16 FRI, 8:15 to 9:17, Arrived on site for unit just stopping . Unit was on warm cycle and found hot water supply valve shut off. Ran diagnostics test no error codes ran both auto and Manuel test cycles all checked normal . No water leaks detected with unit at time of service . Did point out with daughter over phone to have plumber check cold shut off valve cause there is a small drip . Job complete .; Job Cmpltd, saved tckt [SdLink\180146a.png], saved tckt [SdLink\180146b.png], snapped 1 QuickPics (via SDM)
Near Austin, TX 78724
Joseph C.
Job Details: 05/14/2018
KRMF706ESS01 refrigerator Arrived on site for “no lights working in fresh foods or freezer” complaint. Inspected unit and found led supply board to be faulty. Removed and replaced led control board. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78724
Joseph C.
Job Details: 05/14/2018
Near Georgetown, TX 78633
Jonathan S
Job Details: 05/14/2018
Whirlpool refrigerator model #WRF540CWHZ. Freezing food in the refrigerator compartment.
Near Austin, TX 78731
Paul
Job Details: 05/14/2018
Whirlpool Refrigerator Model WRB119WFBM00. Arrived onsite for the refrigerator with the crisper drawers hard to open. I replaced the shelf frame and drawers that were diagnosed as defective on the previous visit. Call complete.
Near Austin, TX 78741
Connor M.
Job Details: 05/14/2018
WED4815EW0 whirlpool dryer Arrived on site to test unit for long dry cycles. Found duct crushed in rear of unit. Confirmed proper function of heater. Pulled dryer from wall to correct issue. Instruct on proper venting and fire hazard.