Near Austin, TX 78749
Kevin
Job Details: 06/01/2018
Arrived on site and attempted to cycle icemaker manually and found that motor is failing and it is not turning. Replaced ice maker and it began cycling immediately and filled with water. No water leaks from connections at time of service, job complete.
Near Cedar Park, TX 78613
Steve C.
Job Details: 06/01/2018
Near Austin, TX 78758
Scott
Job Details: 06/01/2018
Maytag dryer or drying clothes . Clogged vent
Near Temple, TX 76501
Dona
Job Details: 06/01/2018
Arrived on site for unit only running for 5 minutes and then will shit itself off, ran unit with wet clothing inside and found the timer is stopping, not allowing unit to continue through cycle. Motor is starting with push to start, not stalling no noise on motor and is not showing as overheating. replace the timer and thermostats as stalling in certain position, can wear thermostats and cause erroneous readings. Replaced timer and thermostats. Unit is running for correct amount of time, no longer stopping in cycle. Units element checks good. Unit is ducted very shortly, duct clean good airflow. All parms check correctly.
Near Meadowlakes, TX 78654
Thomas L.
Job Details: 06/01/2018
Arrived on site for no cool condition. Control would not accept command to enter diagnostics. Found thermister out of operating range. Replaced both.
Near Dripping Springs, TX 78620
Brandon
Job Details: 06/01/2018
Arrived on site for part hanger, I replaced freezer brackets, replaced rc thermistor with fan motor and support, sealed the freezer compartment, unit tested good. Water lines were dry at time of service.
Near Johnson City, TX 78636
Connor M.
Job Details: 06/01/2018
KUIX505ESS2 kitchenaid ice machine Arrived on site to install recirc pump for repair. Installed and monitored an entire harvest cycle. Ice is now proper thickness. Unit working properly, no leaks detected.
Near Temple, TX 76502
Dona
Job Details: 06/01/2018
Arrived on site for previous technician Tested the unit ice maker and received error code E2 lost position. Also found excessive ice build up in the facia heater. Found no voltage to the facia heater due to the control is defective. Replaced electronic control kit and ice maker. Checked that unit had no errors and went through harvest test 57. Completed harvest. Unit called for water. Unit started ice production. All water connections dry.
Near Leander, TX 78641
Lou
Job Details: 06/01/2018
arrived on site to install previously diagnosed and ordered parts. I removed and replaced the entire dispenser assembly and replaced with all new parts. Tested unit and unit operated as designed. No water leaks observed during service. Job completed.
Near Austin, TX 78732
Luis
Job Details: 06/01/2018
Refrigerator-replaced main control board
Near Austin, TX 78757
Scott
Job Details: 06/01/2018
Arrived on site for door issues .did get unit to give open/ close message after playing with door a few times . Replaced all micro switches and both interlocks . Checked door brackets and frame, all checked good .
Near Harker Heights, TX 76548
Dona
Job Details: 06/01/2018
Arrived on site for unit producing dL error code on every other cycle. Found that motor control is not always sending voltage to lid lock. Will need to replace much due to this error and lid lock due to intermittently working. Unit will spin when lid is locked. Found grinding on bearing during spin. Will need to replace bearing as well. Will need 2 hours repair time. Cnotes. Will also need authorization for repair. Unit is in a new home and on gfci. All water connections dry. Susan assisted.
Near Harker Heights, TX 76548
Dona
Job Details: 06/01/2018
Arrived on site for intermittently drying, ran unit through 2 full timed dry cycles, found temperatures normal. Airflow correct. Unit did not overheat. No abnormal noises. Drum turning correctly. Unit shut off, and when started in new cycle unit started heating again. Timer is counting down correctly. Venting clear. All parms check good on unit.
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details: 06/01/2018
Arrived on site for noisy spin cycle. Remove wire from basket. Spin cycle is now at a normal sound level. All water connections were dry.
Near Leander, TX 78641
Lou
Job Details: 06/01/2018
arrived on site to inspect washer running too long. Upon inspection, the customer advised that he had put bedding in the unit and ran wash on rapid wash and it appeared that the unit ran for more than 3 hours. He advised that the unit was vibrating very badly. I placed the unit diagnostics and the unit show error codes 8/6, 7/8, 0/3, 0/5. I cleared the error codes and continued with diagnostics. Once the unit was done, there were no error codes. I verified the rotor and stator were good and I tested unit in high speed spin to verify. Unit tested good in high speed spin. I instructed the customer on detergent and softner use as they were pouring the detergent directly into the unit and into the dispenser. I instructed the customer on the amount of detergent and softner to use as well. Advised the customer on size of loads and which wash modes to use depending on clothing and bedding. No water leaks observed during service.
Near Dripping Springs, TX 78620
Kevin
Job Details: 06/01/2018
Right on site and found refrigerator is showing power on user interface but there is no cooling function. Found that refrigerator was still in show room mode. Retailer did not clear show room mode after refrigerator was installed, compressor has started running and recommended to customer that refrigerator be allowed to call for 24 hours to reach correct temperature. No water leaks from connections at time of service, job complete
Near Hutto, TX 78634
Cliff
Job Details: 06/01/2018
Maytag washer MVWC300VW0. Arrived on site to diagnose a washing machine that is leaking. Tested unit and found no failures to washer itself at this time and no leaks inside unit. Did note customers drain backing up to the point it’s causing a syphon to occur on drain line. Advised homeowner she’ll need a plumber to come correct drain issue. In combination with a water softener the drain issue is most likely cause of leak, as excess sudsing would leak out of top of drain pipe. No for the repairs needed by appliance express and homeowner is contacting plumber to complete repair.
Near Driftwood, TX 78619
Connor M.
Job Details: 06/01/2018
WFW94HEAW0 whirlpool washer Arrived on site to test unit for not draining well. Found no stored error codes. Ran diagnostic cyle and found drain pump operating as designed and motor reaching target rpm. Instruct on proper use and care. No leaks detected.
Near Driftwood, TX 78619
Connor M.
Job Details: 06/01/2018
WGD94HEAW whirlpool dryer Arrived on site to test unit for long dry cycles. Found duct in rear of unit in between dryer and gas line coming from floor to be crushed almost completely. Instruct customer on ocrrecting vent issue and having vents checked. Made aware of potential fire hazard.
Near Driftwood, TX 78619
Connor M.
Job Details: 06/01/2018
KERS306BSS0 kitchenaid range Arrived on site to test unit for sparking during use. Found full failure on bake element. Ordering for return. Ja approved 6/5
Near Leander, TX 78641
Lou
Job Details: 06/01/2018
arrived on site to install previously diagnosed and ordered part. Removed and replaced the element and tested unit. Unit operated as designed. No lint observed during service.
Near Austin, TX 78731
Luis
Job Details: 06/01/2018
Refrigerator-defrosted water reservoir tested water dispenser good icemaker filled with water
Near Georgetown, TX 78633
Steve C.
Job Details: 06/01/2018
Arrived on site for the unit is not making ice. Tested the unit is diagnostic and the ice maker passed. Called Whirlpool Sr#7722124664 and advise to replace the evaporator cover. The control already has the updated version. Replaced the evaporator cover and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Austin, TX 78759
Scott
Job Details: 06/01/2018
Arrived on site for dryer taking long and multi turns to dry . Ran an air vent check with and with out vent hose and found with check kit that exterior vent is clogged . Unit is heating normal . Recommended to customer to have vents cleaned out . No lint build up at time of service
Near Belton, TX 76513
Dona
Job Details: 06/01/2018
Arrived on site for dishes not cleaning well, found sump with debris removed, verified water flow verified amp dram all parms check good. Found customer will need to adjust incoming water temps as it is below 120. Instructed customer on detergent and rinse aid usage. 1 wheel off each wheel assy is broken, Will need to replace all four wheels . Customer will install parts. All water connections dry. CS authorized D2C parts.
Near Buchanan Dam, TX 78609
Thomas L.
Job Details: 06/01/2018
Removed and replaced broken hose. Quick disconnect had cracked and would not secure hose.
Near Buchanan Dam, TX 78609
Thomas L.
Job Details: 06/01/2018
Arrived on site for Noisey operation. Found condenser cover vibrating. Corrected loose panel. All water connections were dry.
Near Austin, TX 78731
Luis
Job Details: 06/01/2018
Refrigerator-replaced failed icemaker
Near Wimberley, TX 78676
Connor M.
Job Details: 06/01/2018
KERS306BSS0 kitchenaid range Arrived on site to test unit for sparking during use. Found full failure on bake element. Ordering for return. Ja approved 6/5
Near Wimberley, TX 78676
Connor M.
Job Details: 06/01/2018
M1TXEGMYW01 maytag refrigerator Arrived on site to test unit for water in freezer and ff compartment. Found drain valve clogged. Cleaned valve and defrosted evap pan. Unit working properly, no leaks detected.
Near Belton, TX 76513
Dona
Job Details: 06/01/2018
Arrived on site for right ff door plate was catching on hinge. Added 2 washers to bring door up found it is now sliding smoothly. Found ice maker metal bail arm was not inside of motor mechanism, not allowing for ice maker to cycle. Reinstalled bail arm so that it would move cycle. Unit dumped ice that was already made and called for water for new ice production. All parms check good. All water connections dry.
Near Austin, TX 78753
Scott
Job Details: 06/01/2018
Arrived on site replaced latch 103.27, labor 80.00. Tested unit all checked good . Checked lock all checked good Collected 198.32 ck1107. No water leaks detected at time of service . Job complete . Maytag top load extra large capacity washer .laundry
Near Austin, TX 78744
Kevin
Job Details: 06/01/2018
Arrived on site and inspected the refrigerator and found dent on the left hand fresh food door, also found one shelf on the interior is scratched. Will need to order both to correct issue, informed customer delivery time for new doors is 6 to 8 weeks. No water leaks from connections at time of service.
Near Temple, TX 76502
Dona
Job Details: 06/01/2018
Arrived on site for excessive noise, found when compressor is running tubing by condenser fan is excessively vibrating causing very loud noise. Added sound dampeners to area and noise greatly reduced, temperatures check good on both fridge and freezer. All water connections dry.
Near Temple, TX 76502
Dona
Job Details: 06/01/2018
Arrived on site for no heated dry, removed toe kick to test amp draw and found right wire on harness to element not attached to heating element. Reattached wire to element and ran through diagnostics. Found amp draw correct on element. All parms check good. Customer is using rinse aid. All water connections dry
Near Temple, TX 76502
Dona
Job Details: 06/01/2018
Arrived on site for low cool condition, freezer is now at 26 degrees and fridge is at 41 degrees. No longer making ice either. found ff evaporator with only partial frost pattern. Will need to replace ff evaporator due to restriction. Will need uv drier, compressor, stub and ff evaporator. Will need 3 hours repair time CNOTES. Melissa assisted. All water connections dry.
Near Bertram, TX 78605
Thomas L.
Job Details: 06/01/2018
Removed and replaced out of range thermister and control that would not allow diagnostics to be performed.
Near Buda, TX 78610
Kevin
Job Details: 06/01/2018
Arrived on site and inspected refrigerator and found ice build up blocking evaporator drain. Removed ice and cleared drain and refrigerator is now operating properly. All other functions are good, no water leaks from connections at time of service, job complete
Near Buda, TX 78610
Kevin
Job Details: 06/01/2018
Arrived on site and inspected refrigerator and found ice build up blocking evaporator drain. Removed ice and cleared drain and refrigerator is now operating properly. All other functions are good, no water leaks from connections at time of service, job complete
Near Lago Vista, TX 78645
Lou
Job Details: 05/31/2018
arrived on site to inspect dishwasher dispenser gasket hanging out. Upon inspection, I did find that the dispenser gasket was hanging out of the dispenser door. I removed and replaced the dispenser and tests the unit in diagnostics. Unit operated as designed. No water leaks observed during service.
Near San Marcos, TX 78666
Connor M.
Job Details: 05/31/2018
WRS571CIDM01 whirlpool refrigerator Arrived on site to test unit for not dispensing ice. Found dispenser motor failed due to previous issue. Replaced and tested unit. Unit working properly, no leaks detected.
Near Belton, TX 76513
Dona
Job Details: 05/31/2018
Arrived on site for low cool condition, freezer is now at 26 degrees and fridge is at 41 degrees. No longer making ice either. found ff evaporator with only partial frost pattern. Will need to replace ff evaporator due to restriction. Will need uv drier, compressor, stub and ff evaporator. Will need 3 hours repair time CNOTES. Melissa assisted. All water connections dry.
Near San Marcos, TX 78666
Connor M.
Job Details: 05/31/2018
WRS571CIDM01 whirlpool refrigerator Arrived on site to test unit for not dispensing ice. Found dispenser motor failed due to previous issue. Replaced and tested unit. Unit working properly, no leaks detected.
Near San Marcos, TX 78666
Connor M.
Job Details: 05/31/2018
MHW3505FW1 maytag washer Arrived on site to test unit for buzzing and humming when drum rotates. Found control sending improper voltage to stator. Replaced control and tested unit. Unit working properly, no leaks detected.
Near Buda, TX 78610
Kevin
Job Details: 05/31/2018
Arrived on site and inspected dryer and found only 120 V showing at terminal block an entire leg is missing. Inspected breaker on the outside of the home and it is weak/failing. After resetting breaker dryer will now run and heat properly, recommended to customer that breaker be replaced, job complete
Near Buda, TX 78610
Kevin
Job Details: 05/31/2018
**Attached pictures to assist with directions** arrived on site and found cold valve of incoming water has very little flow. Inspected cold water line and found sediment buildup on valve screen. Valves will need to be replaced to correct issue and suggested to customer that a permanent solution for high mineral content in water would be necessary to keep washer working. No water leaks from connections at time of service, job complete.
Near Leander, TX 78641
Thomas L.
Job Details: 05/31/2018
Arrived on site for no cool. Fresh food evaporator was not defrosting. Found defective defrost thermostat via diagnostics. Replaced. Unit is so iced up that the rest of the ice that I could not remove will have to be removed by turning unit off. Customer to lay towels on floor on all sides of unit to,catch any water overflow. Part $172.89 Work$179.99
Near Killeen, TX 76543
Dona
Job Details: 05/31/2018
Arrived on site for noise complaint from customer, found underwire of bra stuck inside between drum and seal rubbing on front of unit. Removed underwire, verified temperatures and tumble has no abnormal noise. Unit is now running to spec once underwire removed. Dryer vent clear. Airflow is good, temps good.
Near Austin, TX 78744
Kevin
Job Details: 05/31/2018
Arrived on site and inspected cooktop and found after uninstalling left front infinite switch harness connector is not attached. After fixing connector all function has returned to cooktop, job complete.
Near Austin, TX 78744
Kevin
Job Details: 05/31/2018
Arrived on site and inspected cooktop and found after uninstalling left front infinite switch harness connector is not attached. After fixing connector all function has returned to cooktop, job complete.
Near Austin, TX 78746
Connor M.
Job Details: 05/31/2018
JFC2290REP00 jennair refrigerator Arrived on site to test unit for no cool. Found evap fan motor trying to turn but binding up on rubber damper holding it to fan shroud. Corrected issue and tested unit. Unit working properly, nomleaks detected.
Near Killeen, TX 76542
Dona
Job Details: 05/31/2018
Arrived on site for no ice production, major ice build up on left side of freezer and ice build up around fridge on back of unit. Per W10772228D and W10842568 will need to replace the control kit, will need to replace the adapter kit on fridge, will need a new seal for freezer door and will need a new ice maker. Will need authorization for this repair, cnotes. Office will reschedule due to needing authorization. Jordan assisted.
Near Austin, TX 78744
Kevin
Job Details: 05/31/2018
Arrived on site and found saved code F3E1 waterlevel sensor error, Confirmed pressure hose is clear and ran a diagnostic cycle and it completed properly. If situation happens again will need to bring back pressure hose and pressure switch to correct issue. No water leaks from connections at time of service, job complete
Near Austin, TX 78744
Kevin
Job Details: 05/31/2018
Arrived on site and inspected refrigerator and found fresh food in the evaporator is frozen over and fridge will need to be defrosted and thermistor and fan replaced. Explain to customer that fridge will need to be disconnected from power for 24 to 36 hours to remove the ice. Customer has signed refrigerator defrost disclosure. No water leaks from connections at time of service
Near Austin, TX 78744
Kevin
Job Details: 05/31/2018
5/31/18 11:18: KB there 5/31 THU, 8:26 to 10:06, Arrived on site and found dishwasher is not filling with water, replaced fill valve and diagnostic cycle is now running properly. Also found water temp is not 120 degrees at its hottest, recommended that customer inspect hot water heater for correct operation. No water leaks fron connections at time of service, job complete.; Job Cmpltd, snapped 2 QuickPics
Near Austin, TX 78704
Robert
Job Details: 05/31/2018
WRS571CIHZArrived on site and replaced loud and clicking diffuser in refrigerator. All sounds and fu
Near Austin, TX 78704
Robert
Job Details: 05/31/2018
GHW9400PW Arrived on site. Checked washer for leaving water in drum and wet clothes at the end of th
Near Georgetown, TX 78633
Steve C.
Job Details: 05/31/2018
Arrived on site for the unit will not clean dishes. Found the unit will fill with water and then will not wash. Found the sump and motor is defective. Quoted customer for the part $200.98 and labor dw120 $199.99 plus tax. Customer advise she will get a new unit. Customer only paid for the service fee. All water connections were dry at the time of service.
Near Copperas Cove, TX 76522
Dona
Job Details: 05/31/2018
Arrived on site for no water flow to dispenser, found filter was clogged and needed replaced installed bypass on reservoir assembly to verify. Customer had a new filter, tech replaced filter and bled 2 gallons of water out of unit. Water flow checks good. All water connections dry.
Near Austin, TX 78703
Connor M.
Job Details: 05/31/2018
WRX735SDHZ00 whirlpool refrigerator Arrived on site to inspect unit for damage to pantry door. Found dent. Replaced and tested unit. Unit working properly. No leaks detected.
Near Copperas Cove, TX 76522
Dona
Job Details: 05/31/2018
Arrived on site for unit not filling and not spinning or washing. Found F7 e5 error shifter error. Ran unit through diagnostics found shift motor working properly, acu not sending proper voltage to shifter. Replaced acu, reprogrammed acu, loaded unit with clothing found unit running to spec. Unit checks load size, fills, agitates, drains and spins. All water connections dry. No errors all parms check good.
Near Killeen, TX 76549
Dona
Job Details: 05/31/2018
Arrived on site for no ice production, found stalled ice maker motor, replaced, unit called for water and started ice production. All water connections dry.
Near Killeen, TX 76549
Dona
Job Details: 05/31/2018
Arrived on site for no ice production, found stalled ice maker motor, replaced, unit called for water and started ice production. All water connections dry.
Near Pflugerville, TX 78660
Joseph C.
Job Details: 05/31/2018
DU840SWPU0 Arrived on site for “unit is crooked, in cabinet” complaint. Inspected unit and found right side of unit dropped down, due to right front foot dropping off of flooring. Adjusted and relocated right front foot. Reattached left mounting bracket to cabinet. Unit checks good. No leaks detected, at time of service.
Near Austin, TX 78745
Connor M.
Job Details: 05/31/2018
MEDC215EW1 maytag dryer Arrived on site to test unit for squeaking during use. Isolated sound to motor. Replaced dryer repair kit just in case. Will need to replace motor. Customer going out of town and requesting june11th. Scheeduling call out 2 weeks.
Near Canyon Lake, TX 78133
Daniel A.
Job Details: 05/31/2018
WOS51EC0AS04 Lower sliding rack not extending fully. Removed lower rack. Retaining tab in wrong position behind sliding mechanism. Corrected retaining tab position. Normal operation after service
Near Georgetown, TX 78628
Lou
Job Details: 05/31/2018
arrived on site to inspect water dispenser not dispensing water. Upon inspection, I found that the water reservoir was full of ice. I removed and replaced the reservoir and tested unit and unit operated as designed. No water leaks observed during service.
Near Austin, TX 78703
Luis
Job Details: 05/31/2018
Refrigerator-adjusted brackets screws holding compressor and condenser coil
Near Killeen, TX 76542
Dona
Job Details: 05/31/2018
Arrived on site to install pressure switch and pressure switch hose as unit was repeatedly giving f20 error code. Verified both cold and hot water flow is good. Verified hose in standpipe is correct. Replaced pressure hose and pressure switch, ran through diagnostics checked good. Started normal cycle. Unit filled, stopped filling, agitated, drained and spun with no error codes. All water connections dry. Instructed customer they need to use less detergent unit is oversudsing.
Near Austin, TX 78748
Connor M.
Job Details: 05/31/2018
MVWB835DW0 maytag washer Arrived on site to install control and pressure switch hose. Installed both parts and tested unit. Unit working properly, no leaks detected.
Near Austin, TX 78753
Scott
Job Details: 05/31/2018
Arrived on site for lights not working in freezer section . Checked connections on fresh food light bar , all checked good . Getting voltage in to freezer and checked normal . Replaced freezer light bar and lights are now working . No water leaks detected at time of service , fridge is not hooked up as to it sitting in living room. . Job complete whirlpool fridge side x side .
Near Austin, TX 78703
Luis
Job Details: 05/31/2018
Icemachine-installed tube to recirculating pump
Near Georgetown, TX 78628
Steve C.
Job Details: 05/31/2018
Arrived on site for the unit is leaking water. Found the leak is coming from the sump and motor. Replaced the sump and motor and tested the unit. Unit works properly and all water connections were dry at the time of service.
Near Salado, TX 76571
Dona
Job Details: 05/31/2018
Arrived on site for no tumble during dry cycle. Found belt snapped in half and idler pulley worn down on motor. Replaced idler and belt, verified operations unit checks good. Venting clear, airflow good.
Near Buda, TX 78610
Brandon
Job Details: 05/31/2018
Arrived on site for part hanger, I replaced mullion, unit tested good, water lines were dry at time of service.
Near Jarrell, TX 76537
Lou
Job Details: 05/30/2018
arrived on site to install previously diagnosed and ordered parts. I removed and replaced the left rear valve, right rear burner head/orifice holder and the spark module. Tested the unit and it operated as designed. I verified no leaks at all connections before re-assembling the unit. No gas leaks detected during service.
Near Jarrell, TX 76537
Lou
Job Details: 05/30/2018
arrived on site to inspect fc ice maker not operating. Upon further inspection, I found ice on the Evap cover and on the Evap. I found that the fc door was gapped on the top left corner of the gasket. I adjusted the fc door brackets and reshaped the gasket and tested door and it sealed. I checked the drain tube for gapping and found that it was gapped approximately 1/4 inch. I used manufacturer approved silicone to seal the gap. I also found that the UI was not properly mounted. The customer advised that another company technician had services the unit approximate one week ago and failed to install the UI correctly. I mounted the UI correctly. I advised the customer to not open the fc door for about two hours to give the door gasket time to reshape and seal correctly. No water leaks observed during service.
Near Cedar Park, TX 78613
Chase
Job Details: 05/30/2018
MHW3505 arrived on site and replaced rotor and rotor bolt. Complete tub and drum assembly which included the bearing was replaced previously. All functions of washer check good, no water leaks present after repair.
Near Belton, TX 76513
Dona
Job Details: 05/30/2018
File#7722111215 rich whirlpool techline, W11092686C service pointer. Per whirlpool metal thermistor will need to be replaced with plastic thermistor, will need to hardware this from rc therm. Sealant needs to be installed around the fridge section, as well as two new screws will need to be replaced onto evap cover. Will need to replace the rc therm again as well per whirlpool. Will need authorization for repair. Cnotes. All water connections dry Callie and Jordan assisted.
Near Austin, TX 78754
Joseph C.
Job Details: 05/30/2018
WTW4616FW1 Arrived on site for “unit fills with water, but will not agitate or spin” complaint. Inspected unit and found lid latch faulty. Removed and replaced lid latch. Tested and calibrated unit. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78750
Scott
Job Details: 05/30/2018
Arrived on site for dead dryer . Found no power to outlet . breakers had been thrown . Reset breakers tested all fuses, heater , thermostats . All checked normal . Did recomend having an electrician check outlet and breakers, also to have the duct work cleaned to outside . No lint build up at time of service . Job complete
Near New Braunfels, TX 78130
Connor M.
Job Details: 05/30/2018
WTW4816FW2 whirlpool washer Arrived on site to test unit for agitator assy issue. Found bolt loose causing agitator to break. Replaced and tested unit. Unit working properly, no leaks detected.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 05/30/2018
Model WDT730PAHZ0, Arrived on call for dishes not drying, replaced dispenser that previous tech ordered due to broken and instructed customer on soap and rinse aid use again and must run hot water at kitchen sink before starting dishwasher, no water leaks after repair, call complete.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 05/30/2018
Model WDT730PAHZ0, Arrived on call for dishes not drying, replaced dispenser that previous tech ordered due to broken and instructed customer on soap and rinse aid use again and must run hot water at kitchen sink before starting dishwasher, no water leaks after repair, call complete.
Near Burnet, TX 78611
Steve C.
Job Details: 05/30/2018
Arrived on site to replace the control and thermistor due to not cooling properly. Replaced both parts and tested the unit. Unit works properly and customer has a one year warranty on the parts and labor. All water connections were dry at the time of service.
Near Leander, TX 78641
Lou
Job Details: 05/30/2018
arrived on site to inspect washer not getting clothes clean. Upon arrival the customer advised that unit is continuously not cleaning their clothes and leaving soap residue on the clothing. I placed the unit in diagnostics and tested. Unit operated as designed and there were no error codes at the end. I contacted Techline and spoke to Andrew who advised that there is a service pointer regarding detergent residue; however, it does not include this model. Andrew advised that there is nothing more that can be done to this unit and provided me with SR#7722110477. I advised the customer of Techlines input and advised the customer again to cut back on detergent and to dilute their detergent every time they wash due to having a water softner on their water source. No water leaks observed during service. The part showing for this call was not on shelf at time of retrieving parts for today's service calls as it was not a part for this unit.
Near Killeen, TX 76549
Dona
Job Details: 05/30/2018
Arrived on site for water under unit, found a prior company had been out to diagnose and found drain tube from freezer fitting collapsed and company pushed something through fitting to open water flow. Inspected fitting and it is flowing correctly with water from defrost. Replaced plastic extending from fitting to drain pan. Saw no leaks or drips once replaced. Unit checks good no leaks at this time.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 05/30/2018
Model WRX735SDBM02, Arri ed on call for icemaker not making ice and found icemaker sent is the wrong icemaker, will order correct icemaker with harness and dual valve due to ice maker fill cup frozen over and replacing ice maker due to ice buildup in head and will use ice container on return, skyped office parts and talked to james and will reschedule for 6/4/18 no water leaks at time of call.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 05/30/2018
Model WRX735SDBM02, Arri ed on call for icemaker not making ice and found icemaker sent is the wrong icemaker, will order correct icemaker with harness and dual valve due to ice maker fill cup frozen over and replacing ice maker due to ice buildup in head and will use ice container on return, skyped office parts and talked to james and will reschedule for 6/4/18 no water leaks at time of call.
Near Georgetown, TX 78626
Thomas L.
Job Details: 05/30/2018
Arrived on site for no operation. Tested and found unit to have open for more views. Replaced and tested. Instructed customer to have it checked and vent hose replaced. Enter via key under flowerpot. Replaced key under flowerpot after locking door and leaving. You
Near Leander, TX 78641
Lou
Job Details: 05/30/2018
arrived on site to inspect dishwasher not drying dishes. Upon further inspection, I found that the customer is using detergent pods and no rinse aid. I instructed the customer that using detergent pods is too much detergent for the dishwasher and the dishes won't get washed. I recommended that they switch to a liquid or liquid gel and only use no more than two tablespoons at s time. Also, I recommended that the customer use rinse aid and fill the rinse aid chamber to the top and watch it periodically to make sure it doesn't get low. The customers unit is connected to a hot water source on its own therefore they don't have to run the sink water until it gets hot then turn the unit on. I Iran the unit in diagnostics and unit operated as designed. No water leaks observed during service.
Near Killeen, TX 76542
Dona
Job Details: 05/30/2018
Arrived on site for no cool condition, found bad start relay and capacitor on start relay. Replaced start relay and capacitor, compressor turned on and started running. Inspected for frost pattern. Frost pattern starting to form. Temperatures dropping inside freezer and fridge. All water connections dry. Unit checks good.
Near Georgetown, TX 78628
Thomas L.
Job Details: 05/30/2018
Arrived on site for No operation and burning smell. Opened control panel and found that the control board and the touch panel had burnt and melted. Unit will need both. Mr and Mrs have decided not to repair unit.
Near Manchaca, TX 78652
Kevin
Job Details: 05/30/2018
Arrived on site and replaced all nozzles, valves, and dispenser recommended by tech line on previous visit. This represents all water flowing parts and the entire top section of the washer. The tub ring was also replaced by a previous technician, no other replacement of parts or adjustment could affect operation further. No water leaks from connections at time of service, Job complete.
Near New Braunfels, TX 78130
Connor M.
Job Details: 05/30/2018
KSC24C8EYY02 kitchenaid refrigerator Arrived on site to test unit for not cooling. Found compressor running very hot, no frost pattern. Amp draw on compressor too high. Will need to replace compressor. Needs autho. Needs two hours. Office to schedule directly.
Near Killeen, TX 76542
Dona
Job Details: 05/30/2018
Arrived on site for door not closing all the time, found door latch and catch are not always making connection, will need to replace door latch and door catch. Door seal looks good not worn. All water connections dry. Jordan assisted with reschedule and parts.
Near Cedar Park, TX 78613
Lou
Job Details: 05/30/2018
arrived on site to inspect dishwasher not getting dishes clean. Upon further inspection, I removed and replaced the wash arm and manifold in the top tub. I tested the unit in diagnostics and approximately half way through the test I opened the drawer and found a large amount of suds in the bottom of the tub. I photographed for verification. At the end of diagnostics, there was still a large amount of suds. Again I photographed my findings. I ran the bottom tub in diagnostics and the unit operated as designed. I did find some detergent buildup in the ports of the manifold and wash arm of the bottom tub, along with some food debris which were not there at the last service call. I will ask the office to order a wash arm and manifold for the bottom drawer since the design has been updated and seems to dispense water more evenly as did in the top tub and schedule return service. Also, I advised the customer to cut way back on detergent; to use approximately 1 to 2 teaspoons in both tubs. No
Near Manchaca, TX 78652
Kevin
Job Details: 05/30/2018
Arrived on site and found Condensation buildup along bottom of freezer door gasket and on Mullian in between freezer door and refrigerator door. Found a large gap in between gray cabinet surround and white freezer liner, took one picture. Used sealant to fill in gap and this may stop condensation. Requested that apartment management continue to monitor refrigerator. A new freezer door may be needed, no water leaks from connections at time of service.
Near Austin, TX 78750
Scott
Job Details: 05/30/2018
Arrived on site for microwave not heating . Found mag had failed . Ordering mag , cap, diode . Return 6/4. Whirlpool gold microwave , built in
Near New Braunfels, TX 78132
Connor M.
Job Details: 05/30/2018
KBFS25EVMS00 kitchenaid refrigerator RF440-399.99 arrived on site to test unit for not cooling intermittently. Found compressor running very hot and loud. Compressor runs for a bit then shuts off due to overload relay tripping. Confirmed bad compressor. Part is covered under entitlment labor is not. Collected svc only via cc. KC approved saturday. Allow 2 hours