Near Buda, TX 78610
Kevin
Job Details: 06/27/2018
Arrived on site and found wash LED is solid and nothing is happening. Set washer into diagnostic cycle and found Saved error code for No fill/long fill also found half an inch of water in washer pan, took pictures. Spoke with tech line SR7722327033. Filled the washer while it was tilted back until water level covered gear case and drain pump connections on the bottom of the tub and there’s no leaking. Ran an automatic test cycle and no water was added to the pan. Removed control panel and activated both valves and neither are leaking or cracked. Could not duplicate where water came from, requested that customer continue to observe it. Tech line recommended running a calibration cycle because control was just replaced. Automatic test cycle completed again and requested that customer monitor machine for continued correct operation. No water leaks from connections at time of service, job complete.
Near Georgetown, TX 78626
Thomas L.
Job Details: 06/27/2018
Near Seguin, TX 78155
Connor M.
Job Details: 06/27/2018
MVWB765FW0 maytag washer Arrived ln site to test unit for not filling all the way on deep water wash. Replaced control and tested unit. Unit now filling properly. No leaks detected.
Near Austin, TX 78724
Joseph C.
Job Details: 06/27/2018
WFW85HEFC1 Arrived on site for “control panel not working” complaint. Inspected unit and found display changes multiple times with one press of start button. All connections are secure and unit is getting proper voltage, at correct polarity. Spoke with Ed, at tech line.Ref# 7722333170. Suggestion was made, that unit may be experiencing interference from local airport or radio operations. Ed recommended ferrite choke, for mitigating possible interference. Ordering new control panel, harness and control, as well. Return for repairs on 07/05. No leaks detected, at time of service.
Near Temple, TX 76502
Dona
Job Details: 06/27/2018
Arrived on site to replace timer that would not supply to motor, replaced timer, unit is now running, and heating. Checked temperatures and air flow, all operations check good. Ducting is clear.
Near Dripping Springs, TX 78620
Brandon
Job Details: 06/27/2018
Arrived on site for unit not washing or heating, found wash motor was bad, also found heater circuit to be good but no heat, found control board to be bad, I replaced sump and control, unit tested good. Water lines were dry at time of service.
Near Seguin, TX 78155
Connor M.
Job Details: 06/27/2018
KFIV29PCMS00 kitchenaid refrigerator Arrived on site to test unit for not cooling. Found freezer at room temp and rc at 48. Confirmed leak in rc evap. Compressor running very hot. Replaced compressor and updated evap. Unit held vacuum. Proper forst pattern in both sections. Unit working properly, no leaks detected.
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 06/27/2018
Model KUDS30FXSS8, Arrived on call for leaking water under dishwasher, 5-1 which is door stuck open error, 10-1 which is a dispenser electrical problem, 6-4 which is float switch open error, , checked float switch and is good, also door switch checks good, also dispenser all checked good, instructed customer not to allow anything to get stuck under float or on top of float switch float, replaced door gasket due to leaking a little water from the bottom corners of the doors were gasket would seal to the door, ran dishwasher again and retested and no leaks after repair, reinstalled dishwasher and tested again after leveling dishwasher and no leaks from dishwasher door, gave customer instruction on soap and rinse aid use, rinse aid set to 1 on dispenser and not to use the pod soap packs its to much soap and to switch to liquid and start with 1 tablespoon and if still suds reduce to 1 teaspoon of liquid dishwasher soap and must run hot water at sink before starting dishwasher. No leaks
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 06/27/2018
Model KUDS30FXSS8, Arrived on call for leaking water under dishwasher, 5-1 which is door stuck open error, 10-1 which is a dispenser electrical problem, 6-4 which is float switch open error, , checked float switch and is good, also door switch checks good, also dispenser all checked good, instructed customer not to allow anything to get stuck under float or on top of float switch float, replaced door gasket due to leaking a little water from the bottom corners of the doors were gasket would seal to the door, ran dishwasher again and retested and no leaks after repair, reinstalled dishwasher and tested again after leveling dishwasher and no leaks from dishwasher door, gave customer instruction on soap and rinse aid use, rinse aid set to 1 on dispenser and not to use the pod soap packs its to much soap and to switch to liquid and start with 1 tablespoon and if still suds reduce to 1 teaspoon of liquid dishwasher soap and must run hot water at sink before starting dishwasher. No leaks
Near Kempner, TX 76539
Arthur B.
Job Details: 06/27/2018
GI7FVCXWY00 (French Door Refrigerator) - Arrived onsite for customer complaint of no cool issue inside RC section. Checked temperature in both sections. Found FC @ 3F, RC @ 48F. Found evaporator fan motor in icebox pulsating. Also found no ice production as well. Unit will need new control, icemaker and icebox fan to complete repair. Customer advised that he does not want unit repaired. Advised customer to contact AHS regarding issue. Will order part and OF to R/S once AUTHO is given. All water connections were dry at time of service.
Near Georgetown, TX 78628
Lou
Job Details: 06/27/2018
arrive on site to inspect no water going into dishwasher. Upon further inspection, I placed the unit in diagnostics and tested. The unit filled with water, but the sump/motor did not come on. The drain pump and heating element worked as designed. I removed and replaced the sump/motor assembly and tested the unit and it operate as designed. No water leaks observed. Job completed.
We serviced a
Arrived on site to replace faulty user interface. Replaced interface, started load verified unit is working correctly, all water connections dry. Part-247.45
Model Labor-tl180-90.00 tax-27.84
Near Temple, TX 76502
Dona
Job Details: 06/27/2018
Total-365.29 collected 365.29 on card.
Near Georgetown, TX 78633
Thomas L.
Job Details: 06/27/2018
Arrived on site ice condition. Found 3 wires broken at the freezer door hinge and others frayed. This is killing power to icees.unit will need new freezer door. Door $1300 Work $249.99 Customer will contact manufacturer for assistance. 800-252-1301
Near Austin, TX 78739
Scott
Job Details: 06/27/2018
Door lock , wall oven .
Near Austin, TX 78739
Scott
Job Details: 06/27/2018
Front load washer , door locked and drain pump burned out
Near Georgetown, TX 78633
Thomas L.
Job Details: 06/27/2018
Installed loose door for builder
Near Killeen, TX 76549
Arthur B.
Job Details: 06/27/2018
MAH8700AWW (Front Load Washer) - Arrived onsite for customer complaint of front load washer “walking” when spinning. Tested unit and found leg were not level to floor. Also found unit sits on laminate floors. Adjusted feet to secure to floor. Advised customer to buy corque board or rubber feet to place under legs to prevent walking. Unit works as intended. All water connections were dry at time of service.
Near Leander, TX 78641
Lou
Job Details: 06/27/2018
arrived on site to inspect refrigerator ice maker not working. Upon further inspection, I found that the water tube was dispensing into the ice maker, but the ice maker was not working. I used my jump wire from ports T to H and the ice maker motor did not engage. I jumped ports L to V and the water entered the ice maker. I removed and replaced the ice maker, due to the unit not operating, and tested the ice maker. The unit began to operate as designed. No water leaks observed during service. Job completed.
Near Austin, TX 78724
Joseph C.
Job Details: 06/27/2018
WRS571CIDM01 Arrived on site for “not dispensing ice” complaint. Inspected unit and found ice hopper seat floor with loose screws and not allowing drive gears to seat properly. Tightened screws. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
We serviced a
Arrived on site for f7 e1 error, found keypad is stuck on control. Will need to replace control assy. Ran through quick test found duplicated error and f8e1 error for stuck key on keypad. Unit is unplugged, Rescheduling for Monday 7/2/18 Part is 387.57
Model Labor pr230 219.99 tax 50.12 total of 657.68
Near Salado, TX 76571
Dona
Job Details: 06/27/2018
Customer paid half of total collected 328.84 in check form check #1138 will collect other 328.84 at next visit.
Near Austin, TX 78724
Joseph C.
Job Details: 06/27/2018
WFE530C0ES0 Arrived on site for “F9E0 error code” complaint. Inspected unit and found all wiring securely connected. Removed and replaced control. Tested unit to 350 degrees. Unit is performing as designed.
Near Killeen, TX 76542
Arthur B.
Job Details: 06/27/2018
WTW8240YW0 (Top Load Washer) - Arrived onsite to install new bearing kit to top load washer from prior visit’s diagnosis. Remove faulty bearing and installed new replacement. Reassembled. Also found dispenser leaking as well. Advised customer of additional par cost. Charged for W10187307 (Dispenser) $55.08 and remaining parts and labor. Tested unit. Unit fills,agitates,drain and spins with no issues. All water connections were dry at time of service.
Near Elgin, TX 78621
Nathaniel B.
Job Details: 06/27/2018
Model WFW8300SW03, Arrived on call for to install parts previously diagnosed, installed main control and drain pump and sensor and belt and shocks and ran auto test and ounce finished rechecked for error codes and got no error codes, interface not needed, no water leaks after repair, call complete.
Near Elgin, TX 78621
Nathaniel B.
Job Details: 06/27/2018
Model WFW8300SW03, Arrived on call for to install parts previously diagnosed, installed main control and drain pump and sensor and belt and shocks and ran auto test and ounce finished rechecked for error codes and got no error codes, interface not needed, no water leaks after repair, call complete.
Near Leander, TX 78641
Lou
Job Details: 06/27/2018
arrived on site to inspect dishwasher not draining. Upon further inspection, I found standing water in the tub of the unit. I pressed the cancel button to engage the drain pump and it did not come on. I vacuumed the standing water out and placed the unit in diagnostics and tested. The unit operated as designed; however, the drain pump still did not come on. I vacuumed the water out and removed and replaced the drain pump and tested again. Unit operated as designed and the drain pump operated as well. No water leaks observed during service. Job complete.
Near Austin, TX 78738
Brandon
Job Details: 06/27/2018
Arrived on site for part hanger, I replaced all dispensers and nozzle, unit tested good. Water lines were dry at time of service
Near Round Rock, TX 78681
Thomas L.
Job Details: 06/27/2018
Arrived on site for no cool condition. Found frozen evap coil. Unit did go into defrost and activate heater during diagnostics. Control is not activating defrost during customers normal use. Replaced control and harness and defrosted coils with steamer.
Near Austin, TX 78731
Cliff
Job Details: 06/27/2018
Kitchenaid dishwasher KUDI02FRSS1. Arrived on site to diagnose a dishwasher with a door that is falling abnormally. Tested unit and found both door Link cables broken. Per notes on work or repair is covered under special project code. Replaced both door link cables and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Salado, TX 76571
Dona
Job Details: 06/27/2018
Arrived on site for timer not advancing, found timer stalled and staying in start of cycle, not moving and keeping unit in start of heat cycle. Replaced timer, verified unit is now counting down and working to spec. Dryer ducting clear, airflow checks good.
Near Leander, TX 78641
Lou
Job Details: 06/27/2018
arrived on site to inspect refrigerator ice maker not working. Upon further inspection, I found that the dispenser is operating as designed, but when attempting to dispense ice, the unit made a loud grinding noise. I found that the actuating arm on the ice maker was broken and caused the ice maker to continuously operate causing the water to overflow into the ice bin and binding up the ice bin motor. I removed the ice bin and attempted to remove the ice maker and found that it was frozen to the cabinet. There is a block of ice at the water tube keeping water from flowing into the ice maker. I am ordering an ice maker, ice bin, and air baffle and scheduled return service for 07/02/18. No water leaks observed during service.
Near Austin, TX 78723
Joseph C.
Job Details: 06/27/2018
WDT710PAHZ1 Arrived on site for “dented front panel” complaint. Inspected unit and found dented panel(center). Removed and replaced panel and handle. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Austin, TX 78717
Thomas L.
Job Details: 06/27/2018
Arrived on site for ice clumping and melting together. Contacted manufactuer and spoke with Bruce about both tabs being broken on the ice box liner housing. See pics. Bruce is turning over to advisory department. No repair is being done today. SR# 7722329345 All water connections were dry.
Near Killeen, TX 76542
Arthur B.
Job Details: 06/27/2018
WED4900XW0 (Dryer) - Arrived onsite for customer complaint of dryer still hard starting. Found motor hard to start. Removed motor and installed new replacement. Reassembled and tested. Still getting same issue. Checked voltage to new outlet and found white wire to neutral still drops to 60V when motor starts. Call WPL Techline and spoke with David and confirmed is house wiring issue. Advised customer of finding. Collected for motor and labor. Dryer vent and lint trap was clean of lint at time of service.
Near Granger, TX 76530
Dona
Job Details: 06/27/2018
Arrived on site for no ice production, found from delivery water was not turned on. Turned water on, verified no leaks or drips on line. Unit called for water and started ice production. Freezer door did not come with whirlpool name plate. MS approved D2C to address to send nameplate. Customer will install nameplate. Unit is cooling properly. All operations check good. All water connections dry.
Near New Braunfels, TX 78130
Connor M.
Job Details: 06/27/2018
KDTE334GPS0 kitchenaid dishwasher Arrived on site to test unit for not washing. Fiund cycle starting but no water entering unit. Valve not powering on. Found clip from upper rack under float switch. Removed and tested unit. Unit working properly, no leaks detected.
Near Manor, TX 78653
Nathaniel B.
Job Details: 06/27/2018
Model WMH53520CS6, Arrived on call for the home had a power outage and after power came back on customer set the time on clock and after 5 min time was no longer showing on display but if opened the door on microwave time would then show on display, found that clock energy saver was on so turned it off just on the energy save and waited 8 min. After and time on display did not go out, all checks good, no parts needed call complete. katkarkel@sbcglobal.net
Near Manor, TX 78653
Nathaniel B.
Job Details: 06/27/2018
Model WMH53520CS6, Arrived on call for the home had a power outage and after power came back on customer set the time on clock and after 5 min time was no longer showing on display but if opened the door on microwave time would then show on display, found that clock energy saver was on so turned it off just on the energy save and waited 8 min. After and time on display did not go out, all checks good, no parts needed call complete. katkarkel@sbcglobal.net
Near Marble Falls, TX 78654
Jerry C.
Job Details: 06/27/2018
MVWX655DW1 Arrived to inspect no spin or agitate. I found the gear case lower seal had ruptured and required replacement. I removed and replaced the gear case and cam kit and removed oil from the motor and belt. I calibrated the unit and tested. Operational test good, no leaks observed during service.
Near Leander, TX 78641
Lou
Job Details: 06/27/2018
arrived on site to inspect damage to a range. Upon arrival, the customer advised that he bought the unit and when it was delivered he had to leave on a business trip. When he returned and began the remodel on his home, he went to install the unit and found that the left side panel had a large dent in it and a the cooktop was badly damaged on the right side. The customer notified Home Depot and he is keeping the unit and would like to replace the damaged items. I am ordering a cooktop (black) and left side panel (black) and will return on 07/03/18 for return service. No gas leaks detected as the unit is not completely connected at this time.
Near Austin, TX 78731
Cliff
Job Details: 06/27/2018
Kitchenaid refrigerator KBSD618ESS01. Arrived on site to replace icemaker and water valve for refrigerator. Replaced both parts and tested unit. Found all is functioning properly at this time and water valves no longer seeping. Control is not needed to repair this unit. No leaks found after services were performed.
Near Harker Heights, TX 76548
Arthur B.
Job Details: 06/27/2018
KERS205TSS0 (Freestanding Range) - Arrived onsite for customer complaint of no start activity on freestanding range. When arrived, found control has “Power Loss” error. Was able to cancel and check all elements and oven. All work as intended. Checked voltage to unit. Unit getting 240V. No other issues found.
Near Florence, TX 76527
Dona
Job Details: 06/27/2018
Arrived on site for replacement of washplate due to washplate being worn down on shaft not allowing unit to cycle or move clothes to clean. Replaced washplate and verified unit is now washing clothing correctly. All water connections dry. Unit is working to spec
Near New Braunfels, TX 78132
Connor M.
Job Details: 06/27/2018
WDT970SAHZ0 whirlpool dishwasher Arrived on site to test unit for not drying well. Entered diagnostic cycle and forced heating element. Element powered on. Instruct on proper function. No leaks detected.
Near Harker Heights, TX 76548
Arthur B.
Job Details: 06/27/2018
MSB27C2XAM00 (SxS Refrigerator) - Arrived onsite for customer complaint of no ice producing on SxS refrigerator. Removed icemaker cover and found ice maker motor stopped mid harvest. Found faulty icemaker. Removed icemaker and installed new replacement. Reassembled. Unit called for water as intended. No other issues found. All water connections were dry at time of service.
Near Leander, TX 78641
Lou
Job Details: 06/27/2018
arrived on site to install previously diagnosed and ordered part. Removed and replaced the right front gas valve and tested. The unit operates as designed. I checked all gas connections and found/detected no leaks. Job completed.
Near Leander, TX 78641
Thomas L.
Job Details: 06/27/2018
Arrived on site for no cool condition in fresh food section. Found freezer evaporator severely iced over. Unit is so iced over that it will need to e manually defrosted. Will return with all defrost system and use only what is needed on return. Unit went into defrost during diagnostics but the heater did not come on.
Near Austin, TX 78745
Luis
Job Details: 06/27/2018
Refrigerator-replaced main control and ui
Near Kyle, TX 78640
Brandon
Job Details: 06/27/2018
Arrived on site for part hanger, the outer tub came with the bearings, I replaced the outer tub, unit tested good. Water lines were dry at time of service.
Near Austin, TX 78753
Joseph C.
Job Details: 06/26/2018
KRFC300ESS01 Arrived on site for “no ice production” complaint. Inspected unit and found ice maker supply tube clogged, due to faulty valve. Removed ice from tube. Removed and replaced dual valve. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Lorena, TX 76655
Arthur B.
Job Details: 06/26/2018
KUIC18NNZS0 (Ice Machine) - Arrived onsite to install sealed system components to ice machine from prior tech’s diagnosis. Removed cabinet and removed compressor and evaporator. Installed new replacements using braising methods. Vacuumed unit down to -25PSI. Charged system with 5.25oz of R134a refrigerant. Reassembled. Tested unit. Found good ice slab forming. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Lou
Job Details: 06/26/2018
arrived on site to install previously diagnosed and ordered parts. Removed and replaced the light wiring harness and tested and the unit still did not come on. I removed and replaced the main wiring harness and tested the unit and still, the unit did not operate. At this point, both wiring harnesses, the fuse board, and the main control have been replaced. I verified ohms at the transformer, the magnetron, capacitor, and diode and there is still no power to this unit. I verified voltage at the fuse board, the main power outlet and the power outlet that I was using while testing. I contacted my service manager CS and advised of my situation and he advised that the office would contact the warranty company and advise of the situation and Deem this unit non-repairable. I advised the customer that my service manager had been notified of this issue and that someone from the office would be contacting their warranty company. The customer advised that he would contact the office tomorrow. The
Near Austin, TX 78704
Joseph C.
Job Details: 06/26/2018
MDB4949SDZ0 Arrived on site for “no drain issue” complaint. Inspected unit and found disposal plugged. Removed plug and reconnected drain line. Tested unit. Unit is performing as designed. No leaks detected, at time of service.
Near Georgetown, TX 78628
Lou
Job Details: 06/26/2018
arrived on site to inspect washer over filling. Upon arrival, I found the unit outside in the garage unplugged. I verified that the sensor was working. I ohmed the water inlet valve and found that the valve is open. I advised the customer of my findings and quoted the customer $77.03 for the valve and TL270 $179.99 for service fee/Labor for a total of $278.22 including tax. Customer advised that they would pay the service fee of $108.24 today and wait to see what the insurance company wanted to do about servicing the unit. I advised the customer that the remaining total is $169.98 and that this quote is good for 30 days. No water leaks observed during service and unit remained in the garage unplugged.
Near Austin, TX 78717
Cliff
Job Details: 06/26/2018
Ge dishwasher GDT695SMJ0ES. Arrived on site to diagnose a dishwasher that will not turn on. Found main power wire burned at connection under dishwasher. This was causing no power to reach controls for unit. Repaired wiring and tested unit. Found all is functioning properly at this time. No leaks were found at time of service.
Near Austin, TX 78727
Scott
Job Details: 06/26/2018
Maytag top load washer , not spinning
Near Woodway, TX 76712
Arthur B.
Job Details: 06/26/2018
WDF330PAHS0 (Dishwasher) - Arrived onsite for customer complaint of dishwasher not completing cycles and tripping breaker. Unplugged unit and removed toe plate to access junction box. Found wiring touching metal causing a short. Secured wiring nuts and reinstalled cover. Tested unit. Unit fills ,washes,drain and heats as intended. No other issues found. Was able to snap a picture of closing papers. MS advised that they can push thru. All water connections were dry at time of service.
Near New Braunfels, TX 78132
Connor M.
Job Details: 06/26/2018
WTW8500DW0 whirlpool washer Arrived on site to test unit for off balance loads found front right foot too close to drain recess in floor. Adjusted leveling foot and ran spin. Unit working properly, no leaks detected.
Near Spring Branch, TX 78070
Daniel A.
Job Details: 06/26/2018
ED5FHEXNB00 Not producing ice. Defective icemaker not going into harvest. Eplaced ice breaker. Verified normal ice production/water fill. Cleaned condenser coil. Normal operation after service
Near Woodway, TX 76712
Arthur B.
Job Details: 06/26/2018
KUIC18PNZS0 (Ice Machine) - Arrive onsite for customer complaint of of ice machine making too much ice. Ran ohm test on bin thermistor and found no ohms. Unit will new bin thermistor. P&L are as follows; WP2316399 (Bin Thermistor) $53.25, IM110 $149.99. Skyped EB to obtain authorization to proceed with repair. MS obtained authorization for repair. Removed bin thermistor and installed new replacement. Reverified ohms. Ohms check ok. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78628
Thomas L.
Job Details: 06/26/2018
Near New Braunfels, TX 78130
Connor M.
Job Details: 06/26/2018
WEE745H0FS whirlpool oven Arrived on site to test unit for error code. Found f2e1 indicating stuck/shorted key. Ran keyboard test and found all keys working. Customer stated this happened after a pot of water boiled over and some buttons got wet. This is normal. Ran full diagnostic test; unit passed. Job completed.
Near Georgetown, TX 78628
Thomas L.
Job Details: 06/26/2018
Near Leander, TX 78641
Thomas L.
Job Details: 06/26/2018
Arrived on site for no cooling in fresh food section. Found fan motor has failed . Replaced. No water hooked up to this unit.
Near Seguin, TX 78155
Connor M.
Job Details: 06/26/2018
MVWX655DW1 maytag washer Arrived on site to test unit for grinding during aggitate. Found gearcase failure. Replaced and tested unit. Unit working properly, no leaks detected.
Near Waco, TX 76712
Arthur B.
Job Details: 06/26/2018
WRX735SDHW00 (French Door Refrigerator) - Arrived onsite for customer complaint of French door refrigerator door mullion not closing properly. Found mullion does flip as intended. Was able to use silicone lubricant to lube hinges. Worked mullion. Mullion now flips open and closed as intended. No other issues found. All water connections were dry at time of service.
Near Woodway, TX 76712
Arthur B.
Job Details: 06/26/2018
KDTE204ESS4 (Dishwasher) - Arrived onsite for customer complaint of scratches in handle and panel of dishwasher. Found WPL provided new panel. Removed scratched panel and handle. Installed new replacements. Reassembled. Customer satisfied with new replacements. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78633
Dona
Job Details: 06/26/2018
Arrived on site for dispenser not closing, found rod to spring mechanically not staying on any longer. Replaced dispenser and verified unit is running to spec. Ran unit through diagnostics checked for leaks, all water connections dry. Dispenser-135.53 Labor-dw295-159.99 Tax24.38 Total 319.90
Near Seguin, TX 78155
Connor M.
Job Details: 06/26/2018
WOD51ES4ES00 whirlpool oven Arrived on site to replace failed tod. Replaced and tested. Upper oven still not baking. Confirmed control not sending voltage to elements. Part is expart. Office to schedule directly.
Near Austin, TX 78717
Thomas L.
Job Details: 06/26/2018
Removed and replaced in efficient compressor. New compressor started frosting the evaporator properly. Water connections were dry. Customer asked me to leave the unit pull forward so he could clean and wash behind it. All water connections are dry.
Near Austin, TX 78731
Cliff
Job Details: 06/26/2018
Whirlpool washer WTW4816FW2. Arrived on site to diagnose a washer that is leaking. Found hot water solenoid leaking internally. Replaced watervalve and tested unit. Found all is working properly at this time.
Near Austin, TX 78737
Robert
Job Details: 06/26/2018
WTW5000DW1 Arrived on job for complaints of water in tube and drain issue. Found valve on hot side failed to close completely and is dripping into tub. Replaced valve and run diagnostics. No errors found. No additional leaks detected. Job complete.
Near Seguin, TX 78155
Connor M.
Job Details: 06/26/2018
WRX735SDBH00 whirlpool refrigerator Arrived on site to install parts for repair. Installed separator, seal, and icemkaer kit. Unit working properly, no leaks detected.
Near Seguin, TX 78155
Connor M.
Job Details: 06/26/2018
MFF2558VEM10 maytag refrigerator Arrived on site to test unit arrived on site to install heater. Removed old heater and installed new one. New one is two inches too short. Installed anyway due to having to cut old one to get it out. Will pull on return visit. Reordering heater. Also found ice maker mold cracked and leaking into ice bin which wasnt mentioned on first visit. Ordering both parts for repair.
Near Round Rock, TX 78681
Jonathan S
Job Details: 06/26/2018
Whirlpool refrigerator model# WRS325SDHZ01. Not maintaining proper temperature in RC and dispensing
Near Elgin, TX 78621
Nathaniel B.
Job Details: 06/26/2018
Model ET8CHMXKB01, Arrived on call for buzzing noise from evap fan motor and returning to install new evap fan and seal were inside liner meets outer cabinet on both sections, replaced evap fan motor and sealed were inside liner meets outer cabinet on both sections all checks good, call complete.
Near Elgin, TX 78621
Nathaniel B.
Job Details: 06/26/2018
Model ET8CHMXKB01, Arrived on call for buzzing noise from evap fan motor and returning to install new evap fan and seal were inside liner meets outer cabinet on both sections, replaced evap fan motor and sealed were inside liner meets outer cabinet on both sections all checks good, call complete.
Near Georgetown, TX 78633
Dona
Job Details: 06/26/2018
Arrived on site for f21 error, unit is draining but will not move into spin cycle. Is turning counter clockwise then a slow clockwise 1 time. Pressure sensor is not engaging control to allow for wash or spin. Will need to replace pressure sensor with hose. Pump ohm correctly and seems to be draining each time but will need to bring with due to unit did stall a few times. All water connections dry. Hose-12.84 Pressure sensor-170.90 Pump-190.80. Labor is fl170 169.99 Total -589.45 Will return 6/28/18 Thursday Collected 294.73 on card, customer will pay remaining 294.72 on return trip.
Near Waco, TX 76708
Arthur B.
Job Details: 06/26/2018
WRF989SDAE00 (French Door Dual Evaporator Refrigerator) - Arrived onsite to install water supply valve to refrigerator from prior tech’s diagnosis. Removed faulty water valve and installed new replacement. Reassembled. Tested. Found still no water dispensing. Removed cover and found water leaking from connection to housing and reservoir. Ordering. W11168758 (Reservoir) $26.54 and filter EDR2RXD1 (Filter) $53.27. R/S for Friday 6/29. MS approved our cost for reservoir due to misdiagnosis. Water turned off at this time.
Near Austin, TX 78745
Robert
Job Details: 06/26/2018
MVWC565FW1 Arrived on job to replace motor and capacitor. After replacement of capacitor test washer and operation is normal. No leaks detected at time of service.
Near Austin, TX 78703
Joseph C.
Job Details: 06/26/2018
WFW95HEDW0 Arrived on site for “door latch not unlocking” complaint. Inspected unit and found door latch defective. Per CS, no labor charges. Part is $97.72(pre-tax). Performed test of unit. Unit is performing as designed. No leaks detected, at time of service. Office to collect amount due with credit card, on file.
Near Austin, TX 78749
Luis
Job Details: 06/26/2018
Refrigerator-replaced separator to prevent ice from melting into drip tray
Near Round Rock, TX 78664
Jonathan S
Job Details: 06/26/2018
Whirlpool washer model# WTW5000DW. Not completing spin cycle.
Near Austin, TX 78745
Robert
Job Details: 06/26/2018
WET4024HW0 Arrived on job for complaints of dryer not running for more that a minute. Found wire issue at terminal block. Wrong voltage setup. Corrected miss wire and test dryer. Operation now normal.
Near Cedar Park, TX 78613
Lou
Job Details: 06/26/2018
arrived on site to inspect venthood color changed. Upon further inspection, I found that the top of the flu looks as if it got too hot or even caught fire (took pics). I removed the flu and inspected the inside and found it to look brand new; no burn marks. I advised the customer that he would need to contact Whirlpool customer care and see if the flu can be covered and replaced due to the issue being cosmetic and is not covered under warranty at this time. Job completed.
Near Austin, TX 78749
Luis
Job Details: 06/26/2018
Refrigerator-replaced starter to compressor
Near Cedar Park, TX 78613
Thomas L.
Job Details: 06/26/2018
Arrived on site for no ice condition. Found breaking icemaker harness. See pics. Replaced icemaker and cycled. All water connections dry.
Near Waco, TX 76708
Arthur B.
Job Details: 06/26/2018
KRFF507ESS01 (French Door Dual Evaporator Refrigerator) - Arrived onsite for customer complaint of French door refrigerator not cooling in RC section. Found RC evaporator all frosted up. Removed evaporator cover and used steamer to defrost evaporator. Found RC thermistor wire frayed. Installed new RC harness and reassembled. Found good air flow and frost pattern on evaporator. No other issues found. All water connections were dry at time of service.
Near Hutto, TX 78634
Jerry C.
Job Details: 06/26/2018
WEG745H0FS0 Arrived to inspect range not turning off. I found the customer was concerned about the unit running after bake operations were cancelled. I tested the unit to 350 within normal bake mode and the chassis cooling fan engaged at 155. I allowed a complete preheat and then cancelled. The fan ran until the compartment cooled. I advised the customer the issue is normal. I corrected a mounting hardware issue with the lower control panel. Operational test good, no gas leaks detected during service.
Near Austin, TX 78746
Kevin
Job Details: 06/26/2018
6/26/18 9:59: KB there 6/26 TUE, 9:02 to 9:30, Arrived on site and found icemaker is not completely dispensing production and it is falling behind lift fingers. Replaced ice maker and requested that customer continue to monitor it for correct operation. No water leaks from connections at time of service, job complete.; Job Cmpltd, snapped 4 QuickPics
Near Austin, TX 78746
Kevin
Job Details: 06/26/2018
Arrived on site and manually cycled icemaker but they did not fill with water, removed rear panel and found brown wire is Loose and not inside harness. Took one picture. After correcting harness voltage is now good to valve and manually fill the ice maker. No water leaks from connections at time of service, job complete
Near Georgetown, TX 78633
Dona
Job Details: 06/26/2018
Found f4 e4 error when trying to use sensor cooking, will need to replace humidity sensor. Discussed with home owner- with install above and venting sealed as so, builder will need to remove unit to be repaired. Discussed with CS as well, customer will call when unit has been uninstalled.
Near Dale, TX 78616
Connor M.
Job Details: 06/26/2018
RF364PXPQ2 whirlpool oven Door glass-110.41 CO210-169.99 arrived on site to test unit for broken outer glass. Found outer glass shattered. Replaced and tested unit. Unit working properly at time of service. Collected balance via cc.
Near Dale, TX 78616
Connor M.
Job Details: 06/26/2018
WED4815EW1 whirlpool dryer Arrived on site to install push to start for sticking. Voltage still not corrected. Electrician never even came out and tested. Motor circuit is getting 248vac and heater circuit is getting 0vac. Attached pic of volt meter with improper reading from white to black on sd mobile. Unit cannot be serviced again until it is verified they have their voltage fixed. Instruct on leaving unit unplugged until electrical system is serviced by an electrician.
Near Austin, TX 78723
Scott
Job Details: 06/26/2018
Arrived on site , replaced gear case and clutch . Ran calibration and diagnostics test , all checked good . No water leaks detected at time of service job complete .
Near Lakeway, TX 78734
Luis
Job Details: 06/26/2018
Refrigerator-replaced failed icemaker optics
Near Lago Vista, TX 78645
Thomas L.
Job Details: 06/26/2018
Arrived on site for improper upper rack operation. Found rack adjusters broken causing rack to fall. Replaced. All water connections were dry.
Near Leander, TX 78641
Lou
Job Details: 06/26/2018
arrived on site to inspect venthood light not working. Upon further inspection, I found that the light socket was loose and the light did not seat correctly inside the socket. I removed and replaced the light housing and tested and the light works. Job completed.
Near Leander, TX 78641
Lou
Job Details: 06/26/2018
arrived on site to inspect dishwasher not drying dishes. Upon further inspection, I placed the unit in diagnostics and tested the unit. The unit operated as designed. I recommended that the customer switch detergents from using pods to a liquid or liquid gel due to the pods producing too much suds. Also recommended the customer us rinse aid, which she does. Advised the customer that the unit is operating as designed and to use it on heavy mode and hi temp to assist in drying. No water leaks observed during service. Job completed.
Near Round Rock, TX 78665
Jonathan S
Job Details: 06/26/2018
Whirlpool refrigerator not dispensing ice.
Near Austin, TX 78730
Cliff
Job Details: 06/26/2018
Whirlpool microwave UMV1160CS3. Arrived on site to replace fan motor for microwave. Replaced motor and tested unit. Found all is functioning properly at this time.