Arrived onsite for the washer not working properly. Ran diagnostics and found errors codes F8E3 for overflow / suds . Ran a quick test and all functions tested good. Ran a normal cycle and washer tested good. Complete

"Arrived on site to diagnose microwave oven combo that is making noise when oven is on. Found blower is rattling when its running causing excessive noise. Replaced blower and retested. Found blower is working as designed and no longer making noise. Found the convection element blown and fried 2 wires in the harness. Cut wires off and wire nutted to make sure no further damage can occur. Call complete."

Arrived onsite for dishwasher not heating. Upon inspection of the diagnostics cycles I found the unit was filling washing and draining but there was no heat when called for after drain. There was also no amp draw from the heater When engaged. I could also see the heater looks visibly shorted or burnt. I quoted 210.44 + tax for svc fee parts(60.68) and labor(149.76) to replace the heating element. Ordering heater(W10518394 ) Office to R/S due to part availability. ; ordrng 1 W10518394 (Heater)

"Arrived onsite for refrigerator making loud noise. Upon arrival could not identify any abnormal noise. Disconnected unit for a few minutes then plugged back in to test startup amperage. Upon starting recorded .9-1 amp with no noise. Allowed unit to run over and hour, compressor did cycle a couple times and still no noise. Could not verify complaint or duplicate noise. Jo complete"

"Arrived on site to inspect dryer for not allowing a correct seal, upon inspection found the seal fraying and coming off the door, reattached seal with glue and let dry. Complete"

"Arrived on site for error code and cooling complaint. Diagnosed a defective evaporator fan motor,replaced fan motor fan powering on and error code no longer on display."

"Arrived on site for fridge not cooling right. I inspected the unit and work area. I spoke to the customer and they stated that once they cleared out the freezer it started cooling properly again. I gained access to the evaporator and found a full frost pattern. I tested the thermistor, the defrost harness and the heating element I found all I. Good condition. I found the fan operating as designed. I spoke to the customer and determined the issue was because the freezer door wa not closed properly and causing condensation at the roof of the freezer. Job complete.

Arrived onsite for questions about drying and provided customer instruct on best practice for improved drying results. Also advised customer on unit capabilities and design. All checks good.

Arrived on site to diagnose a refrigerator that is not producing ice. Found icemaker fill tube frozen over. Thawed tube and all is working properly at this time and no leaks were found at time of service.

Arrived onsite for refrigerator not dispensing ice properly. Upon inspection found ice bucket bar not in line with ice wheel. Disassembled bucket compartment and re assembled in line. Tested unit and unit is functioning properly. Unit is dispensing cubed and crushed ice. Job complete

Arrived on site to replace interface per previous tech. Removed interface to inspect connections and verify part is needed. Immediately found control board has a damaged relay(took pic). Did not install new interface to prevent damage. Ordering new control board and UI board. Office to reschedule. ; ordrng 1 W11333816 (UI BOARD) and 1 W11342846 (CONTROL)

Arrived on site to replace previously ordered parts for refrigerator..; ordrng 1 W11415785 (Tube)

Arrived onsite and found unit operating with failing console. Replaced console. Unit is now operating as designed. Advised customer On repair.

arrived on site to test unit for no power. Test unit and found bad fuse. Replaced fuse test unit and unit heating job complete.

Arrived onsite for the F1E4 error code. Replaced control board and error code is gone. During testing found that the turn table was not turning and it was not heating. Found that the secondary switch was not making contact. Found that the cabinet was bent inward causing the issue.

Arrived on site for washer not operating tested and inspected unit and found failed main control (See service pointer) unit is stacked and in very tight spot. Will need 2 man 2 hour job. Office to schedule return trip. No water leaks present at time of service.; ordrng 1 WPW10367632 (RFI FILTER) and 1 W11046209 (Pump) and 1 W11044866 (Pressure switch) and 1 W11044834 (Valve) and 1 Seenote (2 man job) and 1 Seenote (2 hour job) and 1 Seenote (Office to schedule)

Arrived on site for ice machine not making ice and only humming. I inspected the unit and work area. I found the unit under warranty. I found the unit humming. I tried to put it into diagnostics and found the UI not responsive. I gained access to the back of the unit and found it has a pump assembly. I unplugged the pump assembly and plugged the unit directly into the wall cutting out the pump. The unit came on. I out the unit into diagnostics and ran a function check. It operated as designed. The unit needs a new pump assembly. I am ordering the pump to complete the repair.; ordrng 1 W10825875 (Drain pump)

Arrived on site to replace previously ordered parts for refrigerator. Replaced both dispenser paddles and tested unit. Found all is functioning properly at this time and no leaks were found at time of service.

"Arrived on site and inspected dishwasher and found saved error code 6/1, Found no water entering dishwasher. Removed valve and inspected it and found screen is completely blocked by debris/calcium residue.

Arrived onsite for wall oven that is losing temp or not staying at temp. Upon inspection I found the sensor connector had a wire backing out and not connecting with the control. I fixed the connector and began testing bake and broil functions. I found the broil element and relay working as designed. I tested the bake relay but found K2 showing no voltage then going up to 20 Vac I found K14 relay showing 240Vac indicating the K2 relay is failing and the control needs to be replaced. I am ordering the control (W10839510) and returning with other parts Incase needed. ; ordrng 1 W10839510 (Main Control)

"Arrived on site for Knocking or Thumping Noise - Top Load Washer. Found basket was not centered and leaning towards the back of washer. Found tub ring wedged and stuck in the back metal panel. Removed tub ring and was able to remove from stuck position where it was wedged. Reinstalled tub ring and basket spins as designed. Placed in diagnostics and ran an automatic cycle. Washer completed all cycles without issue. Washer running as designed, but tub ring is damaged from being wedged underneath the metal panel and will need to be replaced. Ordering tub ring W10849477 to return and complete the repair. ; ordrng 1 W10849477 (Tub ring)"

Arrived onsite for dispenser door not staying latched. Looked at door latch. Found that the actuator was missing. Replaced actuator. Unit tested good. No issues at this time. Job complete.

"Arrived on site to inspect refrigerator interior lights not working. Upon further inspection, I found several lights out in the RC & FC sections. LED modules were recently replaced in this unit. I am ordering 10 LED modules, CNOTE-LSO PER CUSTOMER REQUEST/TRAINING and office to schedule return service. Upon return service, the 10 modules and LED control will need to be replaced. No water leaks observed during service.; ordrng 10 W11462342 (LED MODULE)s and 1 CNOTE (LSO PER CUSTOMER REQUEST/TRAINING)"

"Arrived on site for Similar to before Ice melted in the Ice maker and then it stopped making ice. When this started it began to make noises. And eventually started shutting itself down periodically with a number 3 showing on the screen after confirming the PO POWER-UNEXPECTED SHUT DOWN, ICE MAKER-NOT MAKING ICE/MAKING ICE SLOWLY Error Code :3. Took temps in freezer and fridge. Temps were good. Plenty of ice in the ice maker. Placed in a forced defrost and never heard the element sizzling any water after five minutes. Removed main control and installed new main control. Fridge cooling as designed. Job completed."

"Arrived on site for dryer making strange noise . Found left rear rollers had locked up . Replaced roller with kit ,also replaced all parts int kit . Lint free at time of service. Job complete."

Arrived on site for filter cover being broken. I inspected the unit and work area.I found the filter cover miss molded and not holding closed. I replaced the cover and tested it. It is now staying closed and opening as designed. Job complete.

"Arrived on site to inspect dishwasher door opening during cycle. Upon further inspection, I found the door strike bent downward and the unit mounting bracket not secured on the left. Also found the unit not level. Resecured the unit in the left mounting bracket, leveled the unit and adjusted the door strike and tested. Unit is operating as designed. Made recommendations for use and care, as well as, detergent and rinse aid use. No water leaks observed during service, job completed."

"Arrived on site for not dispensing ice. Found coupling on shaft slipped causing g shaft not to engage ice bin,replaced shaft assembly tested ice dispenser unit working as designed."

"Arrived onsite for dryer taking to long to dry. Upon inspection and use of ventilation tester found customer has external ventilation issues. When unit is not connected to vent hose, unit has good air flow. Instructed customer that the external ventilation system will need inspection and cleaning. Job complete"

"Arrived onsite for unit not getting cold water. Upon arrival put unit in diagnostics and found stored error code for Long fill. Tested valve and found valve was failing. Replaced valve, tested unit and unit is functioning properly. No leaks present at this time. Job complete"

Arrived on site to test unit for drawer not closing all the way. Test unit and found glide was off. Secured glide test unit and unit test good job complete.

"Arrived on site and inspected disposal and found grinder is not properly attached to motor anymore and its not spinning correctly.

"Arrived on site and inspected dishwasher and found tub is slowly filling with water, took a short video. And that water valve is not closing properly and constantly seeping water into tub.

Arrived on site to test unit for broken glass. Replaced glass,Test unit and unit test good job complete.

Arrived on site to test unit for upper spray arm broken. Replaced spray arm test unit and unit test good job complete.

Arrived on site to test unit for f8e0 error code. Found and fan and also found shorted keypad. Will order new console. Will need to replace fan . ; ordrng 1 W10909669 (Console) and 1 W11107275 (Fan blower)

"Arrived on site to install previously diagnosed parts. Removed deli control, hv control, ice maker, dui control, and UI. Installed new deli control, hv control, ice maker, dui control, and UI. Controls all replaced due to the fridge cooling for 17 days as designed then on the 18th day fridge begins to fail. Freezer temps would get to 30s and fridge was getting up to the 50s. The only way to get the unit to function again is resetting the power. It will run anywhere from two days to seventeen days and fail. Fridge is cooling as designed at this time."

Arrived on job to replace control. After replacement test operation compressor started up. No leaks detected at time of service.

Arrived onsite and found harness connection loose to CCU causing inconsistencies in selection response. Cleaned and secured connection. Unit is now operating as designed. Advised customer on repair. All checks good.

"Arrived on site to diagnose dryer that was not heating. Ran unit and verified it is spinning but its not heating. Checked voltages at terminal block. Found 120v from L1 or L2 to ground, but if you run combined voltage you get 0. Checked voltage at the outlet and found same result. Customer will need an electrician to resolve, L1 and L2 appear to be sharing the same leg, which is resulting on the unit getting 120v total. Customer will follow up if issue persists after electrician repair."

Arrived on site to install previously diagnosed part. Removed spark module and installed new spark module. Powered up and still no ignition from bake or broil. Tested bake and broil harness at the spark module and I was getting 120v on broil but nothing from bake. Ordering a new control W10885069 to return and complete the repair. Also returning with all parts just in case. ; ordrng 1 W10885069 (Control)

Arrived on site for dishwasher leaking. I inspected the unit and work area. I found the valve leaking and the supply hose rusting. I replaced the valve and the supply hose. I reassembled the unit and tested it. It is now working as designed. No water leaks detected.

Arrived onsite to replace fill valve. Replaced part. Tested unit. Unit tested good. No leaks at this time.

"Arrived on site to install previously diagnosed and ordered parts. Due to the inlet valve leaking and the ice maker fill tube being damaged, I removed and replaced the valve and green tube and tested. Unit is operating as designed. No further water leaks observed during service, job completed."

Arrived on site to test unit for unit leaking. Found water coming from right side of the unit. Test unit and found unit door not sitting correctly making unit lean right. Secured door test unit and unit test good job complete.

"Arrived on site and inspected washer and found no saved error codes, ran all functions and manual diagnostic and everything checks good. Discussed correct loading procedures, correct detergent usage, and water level and wash expectations. Washer is operating correctly at this time, job complete"

Arrived onsite to install previously diagnosed parts. I installed the FC fan motor and tested function. The fan is working as designed at this time. I emptied the drain pan and ice maker to ensure no double fill. I advised the customer to monitor the unit over the next 24 hours to make sure the temps equalize. No leaks detected during time of service. Job complete.

Arrived on site to diagnose an ice machine that is over producing ice. Found bin thermistor out of range at low temps. Replaced thermistor and tested unit. Found all is functioning properly at this time and no leaks were found at time of service

Arrived onsite for washer with foul odor coming from the bellow. Upon inspection I found the bellow has black splotches around it. I cleaned out the bellow with bleach and water. After cleaning i put a cup of vinegar in the unit and ran a clean cycle. I advised the customer to use her afresh tabs once the vinegar clean is done and run a clean cycle again with just afresh. No leaks detected during time of service. Job complete.

"Arrived on site for a dishwasher that was leaking. Upon arrival the customer stated that the unit was leaking bad enough to be going through the cabinet on the right hand side. He also stated it is an intermittent leak and it makes a loud sound as well. I gained access to the bottom of the unit and could see water marks everywhere indicating major leakage. I found a very very small amount of water buildup in the drain area but no active leak. I put the unit into diagnostics mode and found stored error codes F2E1 for stuck key and F5E1 for door switch open. I ran a diagnostics cycle and monitored the bottom of the unit and observed no leaks. I heard the loud sound at the start of the cycle when the motor initiated and it was a loud hum. I then gained access to the inner door and again observed no leaks. I used my mirror and walked around the sump seal and found no sign of leakage. Although the water marks indicate a potential sump leak. He unit was working as designed and I could not recreate the leak.; ordrng 1 WPW10531320 (Drain Pump) and 1 W11223838 (Toe Plate Insulation)"

Arrived onsite for washer leaking. Upon inspection I found the unit is working as designed. I ran a auto test and found no leaks. I ran manual and let the unit fill up as much as possible to try to recreate any leaks. I found the inlet valve would spray and droplets would form on the back wall and fall down. I noticed the front feet were all the way up and the basket was leaning forward slightly. I adjusted the feet so the basket leans back a little. I could not get the valve to spray anymore. No leaks detected during time of service. Job complete.

Arrived on site to install previously diagnosed door switch. Removed failed part and replaced with new. Tested unit and all operations are normal. No other repairs are needed at this time.

Arrived on site for fridge dispensing water slowly. I inspected the unit and work area. I I tested the water dispenser and found it working slow. I the customer provided a new water filter. I installed the new water filter and tested the dispenser. It is now flowing properly.

"Arrived on sote for ice build on on left side and icemaker tray not attaching to door. Replaced rail and bracket on left side,added grease to icemaker track,added sealer to liner gap,installed door checked door seal good checked icemaker track good."

"Arrived on site to diagnose freezer with ice building On ceiling. Found a small gap where gasket isnt lined up with liner. Door is tilting downward on the left side, making it hard to seal. Tried adjusting hinges and level and cant get door to level out. Ordering new door and hinges. Office to schedule. ; ordrng 1 WP2261963 (Upper hinge) and 1 WP2254618 (Lower Hinge) and 1 LW10599407 (Door) and 1 W10884775 (Badge)"

Arrived onsite and found incorrect door in correct box. Ordering correct Kitchenaid door. Office to reschedule ; ordrng 1 W11400261 (Correct door)

"Arrived onsite for the refrigerator ice maker not making ice and cooling issues. Ran diagnostics and tested ice maker and fill test. It passed. There was no frost build up on evaporator cover. Temperatures are good. Ice box fan tested good , ice compartment thermistor tested good. Set the defrost to come on every 8 hrs. Could not find any issues with the refrigerator at this time .

"Arrived on site for customer complaint of unit not washing dishes, found diverter motor not reaching home position and wash motor failed.

"Arrived on job for complaints of not cooling. Found fans working but no compressor running. Inverter blinking code 4times for failed compressor. Confirmed the 120vac and 6vdc to inverter. Will need to replace compressor, inverter and heat exchanger. CS will look up remaining parts needed. Will need SS repair and tech to complete. ; ordrng 1 W10143759 (drier (service)) and 1 W10629033 (inverter box) and 1 W10841139 (compressor) and 1 W10913906 (coupler)"

"Arrived on site , replaced motor and blower wheel. Unit is now functioning normal. No lint build up at time of service. Job complete ."

Arrived on site to test unit for not cooling in RC. Found evap cover was extremely frozen over. Advised maintenance to unplug unit to allow for proper thaw.

"Arrived on site for customer complaint of oven still heating after customer shut unit down. I tested unit at 350 degrees, then canceled the oven and waited to see if temperature dropped, found unit is working as designed and the blower motor will stay on until cool down is complete.

"Arrived on site to diagnose cooktop that had issues with right 2 burners. Removed cooktop and examined burners. Found the front right burner had an open coil causing it to fail. Rear right burner has burnt inner coil. Checked availability on parts and found we will have front right burner shortly, however right rear burner is showing 0 stock. Advised customer that getting rear right element has no ETA. Customer wants to proceed with front right small corner replacement, and will order right rear burner ; ordrng 1 WP8285938 (Right Rear Burner)"

"Arrived on site for a refrigerator with the ice bin stuck and freezing underneath. Upon arrival customer had already thawed out ice underneath. The customer stated it has been making ice fine, but there is a slow drip into the IM. I put the unit into diagnostics mode and found the IM had an E2 error code for IM lost position and couldnt find home position. I ran a harvest and it harvested s designed. I then ran an IM fill it filled as designed. Upon further inspection I observed water dripping from the water dispenser as well. This is indicating a weeping valve. I gained access to the valve and ran fill test to make sure there were no leaks. No leaks observed at the time of service. The valve is working as designed. Call complete."

"Arrived on site to test unit for not cooling. Found compressor extremely hot. Compressor would start for a couple seconds then shut off. Replaced starter and cap, tested unit, unit still shutting on and off. Spoke with SS thread and recommend replacing compressor. Needing SS tech and 2 hrs on return visit. Office to reschedule.; ordrng 1 ACCESSVALVES (ACCESS VALVES) and 1 W10507884 (compressor) and 1 W11179385 (drier-tube) and 1 WP2188823 (evaporator)"

"Arrived on site for ice build up and water leaking. Found ice build up on evaporator and in drain causing water to leak onto fresh food floor. Defrosted ice build up,checked water flow through drain,drain slightly has bend in middle section. Per service pointer,secured thermistor to correct location on suction line using a zip tie,secured evaporator to back liner wall with clamps and zip ties,reinstalled cover,secured cover with 4 screws,added shims to make drain pan level, hanged defrost setting to basic. used 1 Shims (Shims) from stock"

Arrived on site for washer making noise in spin cycle. Tested and inspected unit and found failed gearcase. Ordering needed part as well as associated parts in case needed. Authorization needed. Office to schedule return trip. No water leaks present at time of service.; ordrng 1 W10528947 (Hub) and 1 W10836496 (Agitator) and 1 W10846191 (Washplate) and 1 W10772621 (Bolt) and 1 W11454372 (Gearcase) and 1 W10832724 (Motor) and 1 W10721967 (Cam) and 1 Seenote (Office to schedule) and 1 Seenote (Authorization needed)

Arrived on job for complaints of not cleaning well. Found the sump screen blocked. Removed spray arm and sump cover to gain access to screen.

"Arrived on site to install previously diagnosed parts to resolve slow dripping water dispenser. Replaced rear valve only. Retested and found flow has increased. Removed filter and found good pressure without filter, but overall pressure is up. No water leaks found. All is working as designed. Calibrated measured fill. Call complete."

Arrived on site for dishwasher leaking from the inlet valve. I inspected the unit and work area. I found the valve solenoid leaking when opening. I installed the new water valve. I tested the unit and found it filling and no leaking anymore. Job complete.

Arrived onsite for the microwave not turning on. During testing found that there is no power coming from the outlet. Found that the breaker was tripped. When I reset the breaker it tripped again with nothing plug into the outlet. Advised customer to call an electrician to check the breaker. Complete

Arrived onsite for refrigerator leaking and not making ice. Upon inspection found fill tube not correctly inserted into icemaker fill cup. Used extension tube to correct issue. Tested unit and unit is functioning properly. No leaks present at this time. Job complete

Arrived on site for oven making popping noises when doors are opened. Upon arrival customer pointed out some screws had dropped into cavity of lower oven. Upon further inspection I found I could not replicate popping sound and customer also pointed out that just a few days prior unit stopped making sound on its own. I did however find that few screws holding the broil element had fallen out and/or come loose from broiler mounts. I was able to apply new screws that were able to hold broiler in place better. Found unit functioning as designed. If customer finds popping noises reoccurring tech recommends replacing hinges.

Arrived on site for a dishwasher not working. I put the unit into diagnostics mode and found stored error code F4E3. I then ran a test cycle and found the unit doing nothing. I checked voltage at the motor and it was getting sent intermittent 80V. This indicates a bad control. I installed a new control and tested the unit again. It was now getting proper voltage. However the apartment does not have water and I cannot properly test the unit. I advised the office of this. Call complete.

"Arrived on site to repair sealed system leak, found leak coming from fresh food evaporator, I replaced evaporator, compressor, filter drier, and coupler, filled with R134A, pressure tested system, unit tested good."

Arrived on job for complaints of middle burner not working properly. Found the convert to LP gas not correct. Too small not enough gas flowing.. ; ordrng 1 W10853432 (spud-orfce)

Arrived onsite for unit another unit not cooling. Checked the freezer and saw that the temperature was at 40 degrees. Looked behind the evaporator cover. Saw unit had an uneven frost pattern. Let customer know that it?s a sealed system issue or low on free on.

Arrived on site for dryer not working when you press start. I inspected the unit and work area. I found error code f25 in diagnostics. I gained access to the interior cabinet and found it lint free. I gained access to the thermostat and fc thermal fuse. I found both open and out of range. I replaced both thermal fuse and thermostat. I reassembled the unit and tested it. It is now working as designed.

Arrived on site to diagnose a refrigerator that is not cooling. When I arrived to inspect unit found all parts and components operating properly and fc at 5 and rc at 38. No repairs needed at this time.

Arrived on job for complaints of latch broken. Confirmed latch damage and replaced latch.

Arrived onsite for the oven making a noise. Found that the lower blower motor is causing the noise. But the blower motor that was sent was way to big to fit . Talked with SW about the issue and they trying to locate the correct part.; ordrng 1 Partresearch (Lower blower motor)

Arrived on site for cook top having improper flames . Found right and left front burner with yellow flaming . Found burner heads and caps slightly warped. Ordering both front caps and burner heads . Back flames normal flame pattern . No gas leaks detected at time of service. Call to set return; ordrng 1 WP8286813 (LF BURNER HEAD ) and 1 WP8286814 (RF HEAD BURNER ) and 1 WPW10597129 (CAPS BURNER )

"Arrived on site for has a bad burning smell when trying to run. Not cleaning thedishes and the wash pods don't get used when going through the cycle, the soap dispenseris closed even once the dishwasher is done/SOAP DISP DOESN'T OPEN DURING CYCLE AND LEAVE MORE THAN HALF THE SOAP INSIDE/RIGHT IN THE BEGINNING WHEN SHE START IT HAS A BURNING PLASTIC SMELL-HAVE CLEARED THE FILTER. Placed in diagnostics and didnt get any errors. Placed in a normal cycle and only got water filling the dishwasher then clicks. After a period of time the dishwasher would drain then fill again and make clicking noises. Tested wash motor and it failed. Removed wash motor and installed new wash motor. Resumed diagnostics and dishwasher tested good. Placed in a normal cycle wash and once again the dishwasher would fill with water then youd hear a series of clicks then drain. It continued this exact process for ten minutes filling clicking and draining. Found main control was faulty. Removed main control and installed new control. Dishwasher is now running as designed. No leaks detected. Job completed."

Arrived on site for refrigerator ice on bottom of FC and dripping. Tested and inspected unit and found failed extension tube allowing water to flow into FC. Removed failed part and replaced with new and removed all ice buildup. Tested unit and all operations are normal. No water leaks present at time of service.

"Arrived on site for refrigerator not cooling. Upon arrival I found compressor, evap fan, and condenser fan running. Evap coil had no moister, ice, or sticky ness to it. Compressor was running hot but high side line as well as dryer had not heat transference. Amp draw was 1.98 to compressor and slightly fluctuating. Found sealed system had failed requiring a new sealed system. Will need to reschedule once availability of parts is known. ; ordrng 1 WPW10507886 (Compressor) and 1 W10836706 (Evap coil) and 1 WPW1014375 (Uv dryer) and 1 W10913906 (Access coupler) and 1 Cnote (Need rescheduled for 2hr ss repair)"

Arrived onsite for washer that wont power on. Upon inspection I found the unit had a stored error code of F6E2 for ACU not heating UI. I replaced the main control and console. I tested the unit and it is now powering on and working as designed. I ran a calibration on the unit and it is working as designed at this time. No leaks were detected during time of service. Job complete.

"Arrived on site for a dishwasher leaking. The customer stated it will for, a puddle in the front right hand side. I put the unit into diagnostics mode and found no stored error codes. I then ran a diagnostics cycle and observed the bottom of the unit for leaks. I found no leaks coming from the sump and motor. I observed a small drip from the front right back of the door. I gained access to the inner door and found the unit leaking from the vent wax motor. You can visibly see the vent gasket and vent deteriorating. They will need to replace the vent and gasket. I also found the heating element rusting and the dispenser starting to deteriorate.

Arrived on job for complaints of not dispensing soap properly. Checked harness and found at the dispenser side the connector damaged not making good connection. Will need upper harness to complete. ; ordrng 1 W11033849 (harns-wire)

Arrived on site to install previously diagnosed drain pump. Removed failed part and replaced with new. All operations are normal. No water leaks present at time of service.

Arrived onsite for the washer making a scrapping noise during spin. Tested unit heard scrapping noise during spin cycle only. Need to reschedule for 2MAN and 2HR for return. Ordered part. Office to reschedule ; ordrng 1 REQUEST (2MAN) and 1 REQUEST (2HR) and 1 W10883783 (gearcase)

Arrived on site for refrigerator not operating properly. Tested and inspected unit and found failed UI. Removed failed part and replaced with new. Tested unit and all operations are normal. No water leaks present at time of service.

"Arrived on site for water leaking. Diagnosed an obstruction in drain tube,cleared drain tube,ran water through drain,water draining correctly."

"Spoke with customer via phone in regards to diagnosis on washer. Customer informed me there is an F5E4 code for lid lock present and lid is not latching. Ordering latch / control / console to resolve, latch is likely only needed part. Customer does not want us to come until we have latch present. Office to schedule when we have latch. ; ordrng 1 W11419171 (Control) and 1 W11394572 (Latch) and 1 W11478526 (Console)"

"Arrived on site to inspect unit for not making ice, upon inspection I found the pump not starting when the bucket was filled, Replaced pump and tested unit, all functions returned and made ice. Complete"

"Arrived on site for no cool in fresh food section. Temp probe reading 53? ran diagnostics weak air flow from vents,ice build up on evaporator cover diagnosed defective thermistors,removed cover assembly,defrosted evaporator,installed new cover assembly secured evaporator thermistor to correct location on suction line,ran diagnostics good air flow changed defrost setting to basic.

"Arrived on site to install previously diagnosed parts. Inspected unit and work area. Replaced interlock kit and tested unit. Unit was still doing the same thing. The customer advised that the unit will heat for over a minute and then will shut off the heat. Ran the unit through diagnostics and did not find any stored error codes. I tested several functions of the unit including the thermistors with all seemingly checking out fine. I called Techline and spoke to Scott SR# 773045999. He advised that he believe the issue to be an issue with the cooling fan not cooling down the magnetron and thus leading to the magnetron overheating and opening the magnetron thermostat. He advised that he did not believe the magnetron thermostat was the issue due to the fact that the thermostat it opens and closes and if it was stuck open, it would not heat again. He advised to return with the magnetron thermostat, the cooling fan, and humidity sensor just in case.Ordering parts in office will need to contact customer about return date due to limited parts availability.; ordrng 1 W10833858 (sensor) and 1 W11230994 (motor-fan)"

Arrived on site for refrigerator needing previously diagnosed UI control as well as high-voltage control. Upon arrival I was able to confirm prior diagnosis and that the unit was having a miscommunication between both main controls after speaking with the office and getting further approval for both parts I was able to reinstall two new controls I then reassembled and tested the unit and verify that everything is fully functioning as designed the unit immediately went into defrost upon repairs indicating that boards were sensing the temperatures accurately now and working call complete

"Arrived on site for an icemaker that is not making ice still. Inspected unit and work area. I called GE Techline and spoke to Don (no file number). Do you advised that all the normal possible repairs have been made to the unit to make the unit function properly. He advised that he needed me to replace the control one last time to ensure we covered all bases Replaced control and tested unit. Unit did the diagnostic cycle but advise customer to call back if the unit does not make any ice. Call the customer back after an hour and she advised that the unit is about to drop the second batch of ice. Advise customer to call back if there are any further problems. Call complete."

Arrived on site for dryer making a loud screeching noise upon arrival I was able to confirm noise after disassembling the unit I found that the noise was coming between two different areas the first area was the rollers inside the unit and the second was coming from the blow will come and detach from the motor. I was able to install a new blower wheel and then I also re-greased the roller wheels because they did not show any signs of physical damage but the metal bearing was slightly rubbing against the metal shaft sat on due to grease being heated and removed from the unit during use after making the repair I was able to reassembled and tested unit and verify that theres no longer any sound coming from the machine and customers happy with repairs. Call complete

Arrived on site and installed the motor and sensor.Tested the unit and unit tested as designed.Customer was extremely satisfied