"Arrived on site and sound water filter will not disconnect. Found Refrigerator shelf assembly is not centered and causing water filter took it caught on the inside edge. Removed shelving and centered it and water filter is now easier/normal to remove and install, job complete"

Arrived on site to diagnose a washer that is not cycling properly. Found shifter out of position stopping unit from agitating. Reset shifter and all is working properly at this time and no leaks were found at time of service.

Arrived onsite and replaced the roller kit. Unit is now operating as designed. Found the pulley wheel had seized. All checks good.

Arrived onsite for refrigerator no cool. Upon arrival I found the FC=12 RC=44. I found the RC evaporator thawed with water droplets on the coils and rust in the drain pan. I found some frost forming on the FC evaporator cover and when I exposed the evaporator I found some ice formed at the top and sides of the evaporator. I confirmed the heater worked through test 6. CS and I walked through SS checks. I ran test 4 and put my hand on the 3 way valve during sub 4 I felt a slight movement and what sounded like a sizzle but not the normal noises a valve should make. I ohmed out the connector at the valve and it ohmed out good. We determined that the 3 way valve is not sending refrigerant to the RC evaporator and will need to be replaced. I advised the customer that there still may be issues with electronics and we would have to quote for those if there are still issues after the valve is replaced. see sd quick pic ) ordering compressor JIC(W10779331) drier(WPW10143759) 3 way valve(W11429997) coupler(W10913906) RC evaporator JIC(WPW10643261) office you R/S; ordrng 1 W10779331 (Compressor) and 1 WPW10143759 (Drier) and 1 W11429997 (3 way valve) and 1 W10913906 (Coupler) and 1 WPW10643261 (RC evaporator) and 1 LOCKRING (LOCK RING)

Arrived onsite for refrigerator RC section not cooling efficiently. Accessed evaporator compartment and found frozen drain line. Defrosted compartment and cleared line. Tested unit and found that RC fan was not working. Unit also needed fan replaced. Tested unit and unit is functioning properly. Temperature stabilizing. Job complete

Arrived on site to install previously diagnosed part. Removed bake burner and installed new bake burner. Tested bake and its doing the same thing. Only ignites on first preheat temp. Afterwards the igniter only clicks and will not light flame. Called techline. Tech line recommended a pressure test based on all items replaced to resolve ignition issue. Replaced bake igniter again to ensure the previous bake igniter wasnt faulty. Tested bake and it is doing the same thing. Called customer and let them know a pressure test must be performed and to make sure and get the report. SR7730889209; O-emld tckt

Arrived onsite for washer with noise during operation. Upon inspection I found stored error codes for over flow and door lock errors. I ran diagnostics and all functions passed with no issues and no abnormal sounds. I advised the customer of my findings. And found them to be on a water softener. I advised that less soap should be used and they might have to start manually putting soap in the detergent dispenser. No leaks detected during time of service. Job complete.

"Arrived on site for wall oven display being locked and not working. I inspected the unit and work area. I found the screen flashing f2e1 key pad disconnected. I pulled the console, disconnected and reconnected all the connections. I powered the unit on and found it still happening. The unit is covered for parts under extended warranty but the service and labor arent covered. .; ordrng 1 W11236887 (Console)"

Arrived onsite to replace part ordered by previous tech. Reply art. Tested unit. Unit tested good. No leaks at this time. Job complete

"Arrived on site for customer complaint of unit exploding, what I found was all 4 suspension rods broke and tub and basket sitting on floor, cabinet/frame was completely damaged, top braces bent, outer basket damaged, pump and lower harness damaged. ; ordrng 1 W10677265 (Cabinet) and 1 Cnote (2 man job/2 hours) and 1 W11224739 (Brace) and 1 W11089573 (Brace) and 1 W11219115 (Outer tub) and 1 W11213337 (Lower harness) and 1 WPW10581874 (Pump) and 1 W11130356 (Suspension) and 1 Cnote (Auth)"

"Arrived onsite for refrigerator still not making ice. Upon arrival found unit valve and ice makers passed all tests 97 and 98 as well as 120 121, found ice maker door gasket unaligned, realigned, found unit rc evap cover frosting by bottom. Ordering unit cover and shims as well as returning with control and UI just in case.; ordrng 1 W11225853 (UI) and 1 Shims (Shims)"

"Arrived on site to diagnose refrigerator not making ice. Customer said they can hear the icemaker move sometimes but dont heat it fill. Ran harvest test and verified icemaker is running. I checked fill and found the valve making a loud hum, and no ice going into the mold. Found fill tube heater wasnt secured to the fill hose well, and barely making any contact to heat the ice. Reseated the fill tube heater and melted out the ice. Tested unit and verified it is filling. All is now working as designed. Call complete."

Arrived onsite and slow ice production but all base functions operating. Ice maker error is e1 no cool. Found icebox temp 24f while ice box fan was on. Ordering control kit per service pointer w10227778D; ordrng 1 W10789393 (Ice box kit.) and 1 W10789393 (Cooling kit)

Arrived on job for complaints of code for sensor. Found sensor plug not secured properly. Reset connector to sensor and test. Sensor passed.

"Arrived on site to test unit for light in FC and upper two lights in RC not working replaced bad modules, tested unit, unit works good. Job complete."

"Arrived on site to test unit for gasket falling off. Found gasket was pulled off on bottom side of FC door. Removed gasket and inspected. Found no damage to gasket. Reinstalled gasket, tested unit, unit works good. Job complete."

"Arrived on site to install previously diagnosed parts. On arrival customer informed me that after unit had lost power back in Feb, it has been working fine ever since and has no had any issues. Advised them that today I would be insulating the reservoir, and blocking off part of the damper vent.

"Arrived on site for ice build up. Found large gap on upper portion of freezer gasket,remolded door seal checked door seal against cabinet good."

Arrived onsite and repaired latch problem with machine by replacing latch. Calibrated unit. All checks good. Unit is now operating as designed.

"Arrived on site to diagnose standalone freezer that is not cooling. On arrival I found the interior at room temp. Customer said it started thawing and dripping, then stopped cooling completely. Performed sealed system diagnosis. Found the evap only had 2 rungs of frost pattern, and compressor is hot. Ordering sealed system parts to resolve. Office to schedule with approval from AIg for sealed system. ; ordrng 1 W10858281 (Evaporator) and 1 W10750851 (Compressor) and 1 WPW10143759 (UV Dryer) and 1 W10913906 (Access valve) and 1 Autho (Autho)"

"Arrived on site to diagnose range that has an indicator light not always on, and also has clock that loses time at random. Recommended replacement of control due to being the power distribution and powering the clock software. Ordering control. Advised customer that there are 2 indicator lights, one is for on and one is for range top hot. There are no issues with the lights, just control to resolve clock losing time. Office to schedule when we get control. ; ordrng 1 W11295990 (Control)"

"Arrived on site and inspected refrigerator and found condensation on the ice door. Replaced ice door, discussed the possibilities of lowering humidity in home with customer prevent prevent condensation. Ice dispenser funnel cannot be adjusted or changed if ice cubes get stuck manual removal is the only alternative, job complete"

"Arrived on site for dishwasher not completing cycle. Inspected unit and work area. Found standing water inside unit. Selected cancel to run drain pump and found good flow of water draining. Performed diagnostics mode and found fault code F9-E4 lower spray arm fault, F8-E1 slow drain and F6-E2 fill valve. Found unit powered off in test mode at fill cycle. Disconnected vent motor and attempted test cycle. Found test cycle completed with vent motor disconnected.; ordrng 1 W10327249 (FILL VALVE) and 1 W10723295 (OWI) and 1 WPW10469574 (VENT MOTOR )"

(Tw) On-site for RC not cooling. Inspected unit. Found damper and return vent frozen over. Steamed ice out of both. Poured water down RC return vent. Found no water returned to FC. Could hear water flowing to bottom unit drip pan indicating hole in insulation.

Arrived on site to test unit for not responding. Found console was acting erratically. Console not responding to commands and making selections on its own. Recommend replacing console(W11112656). Customer stated he just wanted a diagnosis and would be doing repair himself. Not sure what else unit might need. Unable to diagnose without console responding.

Arrived on job for complaints of not washing. Found wash motor not working. Replaced wash motor and test.

(MM) Arrived on site to follow up on dryer making noise. Upon arrival I spoke with customer and I was informed prior technician had placed cardboard in unit in attempts to suppress sound but the noise still persisted. Customer stated they were uncomfortable with cardboard in unit with open flames. I removed the cardboard and informed customer of service pointer to resolve problem. Service pointer W11378591A advises a dryer sound pad and seal kit for blower wheel. Both items placed on order. Advised customer the unit will be louder until next visit for repair now that cardboard has been removed. I ran unit and verified sound was coming from blower area. Office to reschedule. ; ordrng 1 W11401018 (Seal) and 3 W11113654 (Sound Pads)s

"(CS) Arrived on site for dryer making loud noise when running. Upon arrival confirmed noise complaint then disassembled unit and found that the rollers were hollowed out. Inspect motor and idler pulley and found that those were good. replaced rollers reassembled and tested unit and found noise is no longer present. Call complete."

Arrived onsite to replace motor and blower. Replaced parts. Tested unit. Issue did not resolve. Called tech line. Had me run through the unit checking for voltage. All Checked good. Concluded the brand new motor was bad. Suggested to replace motor again. Spoke to Chris got sr#7730950419. Rescheduled with customer. ; ordrng 1 279827 (motor!dryer) and 1 WP694089 (wheel)

"Arrived on site for customer complaint complaint of no ice, found E5 error code, I replaced ice maker, unit passed diagnostic test and fill test, unit tested good."

"Arrived on site and inspected dishwasher and found saved error code 5/2 door not opened in between cycles. Ran a diagnostic cycle and it completed properly. Found no high drain loop in drain hose and corrected it. Sent video of dishwasher motor running to CS. Heating element is on at the end of the cycle. Recommended to homeowner that dishwasher magic be used to clean out the dishwasher. Also recommended that hot water if we run at the kitchen sink until it is at its highest before starting dishwasher. Also recommended using rinse aid to provide the best possibility for drying function, job complete."

Arrived on site to test unit for kick plate not secured and unit not drying. Test unit and found broken clips for kick plate. Installed new clip and test unit and heating element working as designed. Advised customer to use rinse aid to help unit dry. Job complete.

Arrived on site to diagnose a refrigerator that is not cooling. Found start device on compressor failed and replaced it. All is working properly at this time and no leaks were found after service was performed.

(CS) Arrived on site to install previously diagnosed icemaker and hv board. Thermistor still passed test. There were no break in any wire harnesses under door. Found temps in freezer around 5 degrees indicating no problems with cooling. Informed customer after installing parts that it could take up to 24 hours to fill ice bucket. Instructed customer to take temp readings over next week to rule out any potential cooling issues that arent visible while on sight. Unit functioning as designed. Call complete.

Arrived on site to install previously diagnosed part. Removed console control and installed new console control. Powered up oven microwave combo and ran diagnostics. No error codes came on. Bottom left mounting screw that holds slide in was missing and a different black screw was used in its place. The screw that was used no longer threads into the cabinet fascia. I was able to find a torque screw in my loose screw bag and install it to keep the bottom left section of the slide in place. Job completed.

"Arrived on site for an ice machine that is not making ice. Inspected unit and work area. Place the unit in service diagnostics and all tests passed until it went to drain. The reservoir drain pump drain the water out of the reservoir.However, when the external drain pump was running for 10 seconds, the unit power itself off and rebooted. Tested the unit again using diagnostics and had the same issue. Spoke to SR and was advised that this drain pump would take several weeks and that we could not get an ETA for this part. Ordering the part in the office will need to contact the customer about a reschedule date due to a PSP item.; ordrng 1 W10825875 (ext drain pump)"

Arrived on job for complaints of not washing properly. Found the wash motor not working.

"Arrived on site for a microwave that has a display that is losing some parts of the numbers. Inspected unit and work area. Confirmed customers complaint as the top line of the LED is shorting out and if you close the door or press in on the microwave, the lights will come back on. Replaced user interface and tested unit. The unit began working as designed with no issues. Call complete."

Arrived Ed on site for a dishwasher with a broken rack. Upon further inspection I found the top left rail broken. Upon removing the rack the left adjuster also broke. I installed both parts and the customer tested the unit. She found he unit is now working well. Unit is working as designed. No leaks observed at the time of service. Call complete.

Arrived on site for a microwave that won?t turn fee turn table. Inspected unit and work area. Confirmed customers complaint and replaced turntable motor. Tested unit and the unit is now working as designed. Call complete.

"Arrived on site to inspect dishwasher leaking water. Upon further inspection, customer advised that a lot of water, more than a cup, was leaking from the front of the unit below the door. I placed the unit in diagnostics showing error code F6E4. Cleared the code and continued with testing. Unit operated as designed with no leaks. I found the unit is slightly tilted forward and not mounted to the cabinets. Also found the dispenser door broken. I removed and replaced the dispenser and leveled the the unit by raising the front leveling legs. Retested and unit is operating as designed. Customer advised they have a water softener system. I made recommendations for use and care as well as detergent & rinse aid use. No water leaks observed during service, job completed."

"Arrived on site for a dishwasher that has a broken upper rack. Inspected unit and work area. Confirmed customers complaint and found the adjusters broken.Replaced adjuster assembly on both sides and tested the unit. The unit is working as designed.

Arrived on site to install previously ordered parts.Removed and replaced the door and name tag to customers satisfaction.Unit now functioning properly.Job complete

"Arrived on site for a washing machine that won?t spin. Inspected unit at work area. Tested unit in manual spin and agitation tests. Found the unit not shifting from spin to agitation. Checked underneath the unit and found the cam detached from the shifter. Unfortunately, we did not get the part in before service. Ordering the shifter due to the part being out of stock. Office will need to contact the customer about a return date due to an out of stock part. ; ordrng 1 W10913953 (actuator)"

"Arrived on site to inspect refrigerator ice maker not working. Upon further inspection, I tested temps in the FC=4 degrees and RC=38 degrees. I found the ice bin full. Also, I found the ice chute gasket not seated correctly allowing warm air from the RC section up into the ice bin and causing the ice maker sensor to read warmer temps than it should. Adjusted the gasket and checked to make sure it is sealing against the ice bin and it is good now. Also found the ice bin rod was jammed into the motor housing and not allowing the dispenser to dispense cubes; constantly dispensing crushed ice. I adjusted the rod and retested the ice dispenser and it is operating as designed. No water leaks observed during service, job completed."

(CS) Arrived on site to install previously diagnosed ice cutter. Ran diagnostics and found heater now coming on. Informed the customer it would take 24 hours to fill the bin with ice. Call complete.

"Arrived on site to inspect refrigerator leaking water from ice maker. Upon further inspection, I found that the ice dispenser maker fill tube was broken and the customer had someone plug the line until we could service the unit. After getting warranty confirmed, I removed and replaced the ice maker fill tube and tested the unit. Unit is operating as designed with no further leaks. Cleaned up remaining water from behind the unit. No water leaks observed at the end of service, job completed."

Arrived on site and inspected washer closing issues. Confirmed removed and replaced the lid.Unit now functioning properly.Customer satisfied JOB COMPLETE

Arrived on site for refrigerator not cooling. Upon arrival found unit would run but compressor was making a loud grinding noise. Upon further inspection found compressor was shutting off every 20 seconds after it would kick on. Found 120 volts to start device but found start device failed. Tried 2 different start devices it got same results plus compressor was starting to seize up internally. Also found amperage to compressor never went under 8.43 amps. Unit will need a ss repair reschedule for 2 hrs. Office to reschedule once availability of parts is known.; ordrng 1 W10836706 (Evaporator) and 1 WPW10507886 (Compressor) and 1 W10913906 (Access valve) and 1 WPW1014375 (UV drier) and 1 WPW10487115 (Condenser)

"Arrived on site to inspect microwave light not working. Upon further inspection, the customer advised that the venthood light wont turn off. I found no bulb in the socket. I removed the control panel and found the relay on the control bad. I am ordering the main control and office to schedule return service due to the availability of part. Unit is heating properly. ; ordrng 1 W10849846 (Main control)"

Arrived on site for dryer making loud noise. Upon arrival I found the rollers had gone bad. I replaced the rollers and reassembled and tested unit. Found unit functioning as designed and no longer making any noise. Call complete.

Arrived on site and inspected cooktop with element heating issues.Turned the unit on and none of the elements came to a glow even when turned on high.Accessed the junction box and found the voltage was 120/55/175.Customer advised theyve had electrical issues since building the residence.Unit lies within the electricity to the unit and not the unit itself.Customer will contact an electrician to correct the issue.JOB COMPLETE

"Arrived on site and inspected range failing to reach temperatures. Confirmed the complaint and accessed the rear and checked the harness and all connections.Removed and replaced the control and sensor. Tested unit and unit never reached the temperature for the preheat tone to go off. Called SW who walked me through additional steps in testing each individual component.I was advised to return with the main harness, another control and will return with the bake element.Unit also needs authorization from AHS.Office to schedule return services due to customers schedule ; ordrng 1 W11295998 (CONTROL) and 1 W11028535 (Main Harness)"

Arrived on site for dryer not heating. Measured incoming voltage and found incorrect. Customer reset breaker and found correct voltage after reset. Found unit heating with correct voltage. Unit tested good.

Arrived on site to diagnose a venthood with light not operating properly. Found bulb replaced with incompatible type. Builder to install correct bulb.

"Arrived on site and inspected freezer drawer issues. Confirmed the sliding drawer was clicking and not opening or closing properly.I disassembled the door, the top tray and the bottom compartment and found it wasnt sitting properly causing the issues the customer was experiencing.Corrected the issues to customers satisfaction.JOB COMPLETE"

(CS) Arrived on site to install previously diagnosed actuator. Upon installation recalibrated machine and verified the unit agitates in low speed and high speed test cycle. Call complete.

"Arrived on site for noise complaint per customer noise from upper compressor compartment diagnosed vibration noise from cover,adjusted cover added sealer between panel and cover. Ran diagnostics ran compressor no big ration noise from compressor compartment"

"Arrived on site to diagnose washer that was not spinning or agitating. Customer has already changed out motor, pump and coupler. Found the gear case is locked up and basket doesnt move almost at all. Checked under unit and found gearcase oil on the ground, indicating a failed gearcase. Provided estimate for new gearcase with clutch and brake tube. . ; ordrng 1 3360629 (Gearcase) and 1 285785 (Clutch) and 1 WP63292 (Spin Washer) and 1 WPW10080230 (Ring) and 1 285353 (Locking Ring) and 1 W10820043 (Brake Tube)"

"Arrived onsite for washer, F0E2 error code. Upon arrival found unit was being used correctly HE soap and after fresh with close to no soap suds. Tested pressure hose found no damage and could blow through. Found unit error must be control. Replaced control and tested. Unit is now operating as designed. Job Completed."

Arrived on site to test unit for burners not working. Test unit and found module not responding. Test module and found module wires not connected correctly and lp conversion needing to be made. Lp converted test unit and unit test good job complete.

Arrived on site to test unit for unit leaking. Test unit and found damaged gasket. Replaced gasket test unit and by running unit for 20 minutes and no leaks present job complete.

Arrived onsite and replaced gasket. Unit is now operating as designed. Advised customer on repair.

"Arrived on site to inspect unit for not cooling correctly, upon inspection found the freezer thermistor out of range, replaced both thermistor and tested. Complete"

"Arrived on site for washer leaking water. Inspected unit and work area. Disassembled cabinet and bypassed lid switch. Ran unit and found leaking at seam of drain pump. Tested all other components and found operating. . Removed failed drain pump and installed new. Tested operation and found no leaks and unit is draining. Assembled unit and tested operation again. All tested good, no water leaks detected.

"Arrived on site for customer complaint of unit over heating, after hooking up unit to WiFi and customers app I tested unit on 350 to check for proper temperature. Found unit tested good at time of service."

"Arrived onsite for bake element issues. Upon inspection found bake element completely failed. Cooktop is working. Will need bake element replacement. Must insure element is available for repair. Office to reschedule ; ordrng 1 4389585 (element,bake)"

"Arrived on site to inspect unit for condensation on inner door, upon inspection found the wrap bent outward causing air leak, spoke with Andrew at Techline Sr# 7730935507 and was instructed to replaced both wrap and glass to satisfy customer. Office to reschedule ; ordrng 1 W10797359 (WRAP ) and 1 W10797361 (door)"

Arrived on job to replace previously diagnosed parts. After replacement test operation. No leaks detected at time of service.

"Arrived on site for cooktop knobs being damaged. We inspected the knobs and found the plastic has collapsed, causing the knobs to not turn properly and engage the cooktop. I am ordering two new knobs to complete the repair. Reschedule for Friday 6/11/2021; ordrng 2 W11366438 (Knob)s"

"Arrived on site for frost and ice forming in freezer . Found rails failing . Steamed and dried compartment. Replaced rails . Door is properly closing , gasket looks in good shape . No water leaks detected at time of service. Job complete"

Arrived on job for complaints of baking element broken. Confirmed the element is broken.

Arrived on site for cooktop knobs spinning freely. We inspected the unit and work Area. We found three of the knobs cracked and spinning freely. We found one of the valves stuck and not rotating. The parts break down does not tell what valve goes where. I am ordering all 5 valves minus the lock out.; ordrng 1 WB19T10085 (Valve) and 1 WB19T10084 (Valve) and 1 WB19T10088 (Valve) and 1 WB19T10087 (Valve) and 1 WB19T10092 (Valve) and 1 Wb03x25796 (Knob)

"Arrived on site to install previously diagnosed parts. Removed motor, cam, hub, belt, gear case, and latch. Installed new motor, cam, hub, belt, gear case, and latch. Ran calibration once powered back up. Ran auto diagnostics and all cycles completed as designed. Secured washer drain hose to pvc pipe made for ac drain pan overflow to ensure the washer drain hose doesnt come out while in operation. No leaks detected. Job completed."

"Arrived on site for customer complaint of no heat, found burnt heating element wire, while taking unit apart, found felt was completely off the drain, found belt torn up, and idler pulley seized and holes in it.

"Arrived on site to inspect washer not spinning/draining. Upon further inspection, I placed the unit in diagnostics and found error codes F9E1, F8E1, F0E2. Cleared the codes and continued with testing. The unit would not test due to the drain pump not pumping the remaining water out the unit. I removed the front panel and inspected the drain pump and found the motor burnt up. I removed and replaced the dr pump and retested and found the unit continues to not drain the water. I found the tub to pump hose clogged with debris at the tub. Removed the debris and retested and unit is operating as designed. No water leaks observed during service, job completed."

"Arrived on site to inspect washer error codes. Upon further inspection, I placed the unit in diagnostics and checked error codes and found F0E5, F0E9 & F3E3. Cleared the codes and continued with testing and the unit operated as designed. I tested the inlet valve and found the sensor shorted. Removed and replaced the valve and calibrated. Retested and unit is operating as designed.

"Arrived on site to inspect unit for not cooling correctly and causing leaks. Upon inspection found the fan not spinning, Icemaker did not leak and cycled correctly, evap looked normal and frost pattern was good, ordering fan and control. Office to reschedule ; ordrng 1 2315549 (motor evaporator) and 1 W11026017 (contrl-box)"

Arrived onsite to replace previously diagnosed parts. Replaced main control and UI. Did not correct issue. Also found that freezer light would not turn on. Called tech line for assistance. Tech help run voltage checks and found break in voltage from light switch to harness.

"Arrived onsite for refrigerator not cooling. Upon arrival compressor was not running. Then noticed it tried coming on. Ran amp test and recorded 7.4 amps then shuts off. Checked compressor windings and C-R 6.2 ohms, C-S 8.5 ohm and R-S 14.5 ohms. Replaced start relay and compressor kicked on for about 2 min at 8.2 amp then 7.4, then cut off. Compressor is very hot to the touch. Unit is having sealed system issue. Need to order and replace compressor and evaporator and have sealed system technician scheduled for 2 hrs. Office to reschedule ; ordrng 1 W10836706 (evaporator) and 1 W10913906 (coupler) and 1 WPW10143759 (dryer) and 1 WPW10507886 (compressor)"

Arrived onsite for ice maker not making ice. Upon arrival found ice bin full of ice. Customer had complained about production. Unit is filling and harvesting correctly. Customer will monitor.

"Arrived on site for washer not starting cycle. Inspected unit and work area. Performed diagnostics mode and checked fault codes. Found fault code F3-E1 water level fault, F6-E3 miscommunication UI to ACU, F5-E2 door lock and F9-E1 long drain. Cleared fault codes. Ran automatic test cycle and found not getting past first step C0. Powered unit off and found drain pump continues to run. Cleared pressure switch and started test cycle. Found major suds buildup (see SD-QUICKPIC). Monitored test cycle and found all functional operational. Had to clear pressure switch again, due to amount of suds in unit. Ran cleaning cycle. Spoke with customer on suds and continue to run cleaning cycle without cleaner until suds are gone. All tested good, no water leaks detected.

Arrived on site. Replaced defective led module and control power cycled unit all leds working as designed.

Arrived onsite for wine cooler having condensation on door. Upon arrival found unit operating as designed found no condensation on exterior of door. Spoke with customer on getting photos for documentation of issue occurs in the future. Job Completed.

"Arrived on site and inspected GE French door refrigerator cooling issues in the ff compartment.Verified the complaint and found a massive ice buildup in ff compartment behind the deli drawers.Due to the amount of ice and the risk of damaging the plastic interior l showed the customer the issues and had her complete and sign the defrost waiver and advised her the office would call her 48 hours before the follow up appointment, so she can defrost the unit so the repair can be completed.; O-emld tckt"

Arrived on site for no heating microwave. Found mag had failed . Ordering mag . Call to Set return ; ordrng 1 W10626122 (MAG )

Arrived onsite for dishwasher not turning on. Upon arrival found outlet was dead. Found it was off at breaker due to recent storm turned on and tested dishwasher. Found dishwasher now operating as designed. Job Completed.

Arrived on site for a refrigerator making a loud compressor sound. Upon arrival the customer stated he could hear a loud intermittent rattle from the back of the unit. I checked temps and found the RC at 38?f And the FC at 0?f. I found the evap and condenser fan working as designed. I found no mechanical failure with the cooling. I gained access to the compressor and found it working as designed. The customer also stated that water will gush out of the filter housing when changing the filter. I turned the water off at the wall and removed the filter. I then put a towel down and quickly turned the water on and off. I found the water coming out of the housing very fast. This indicates a faulty filter head housing. I am ordering the housing to replaced and the valve just in case. ; ordrng 1 W10408179 (Valve) and 1 WPW10121138 (Filter Housing)

"Arrived on site to install previous diagnosed part. Removed failed door and installed new. Tested dispenser and door operation . All tested good, no water leaks detected."

Arrived onsite and replaced the hv control and ui. All checks good. Advised customer on fridge operation.

Arrived on site to test unit for condensation in FC. Found evaporator had ball of ice on capillary tube. Removed ice and ice started forming again. Refrigerant was not moving through evap preventing unit from cooling properly causing condensation. Needing SS tech on return visit and 2hrs. Office to reschedule. ; ordrng 1 W11092533 (start-dev) and 1 W11209866 (compressor) and 1 WPW10143759 (dryer) and 1 WPW10313899 (evaporator) and 1 WPW10350564 (capacitor)

Arrived onsite and called techline for repeat frozen fill tube. Was advised that tube is able to be replaced. Advised customer on techline recommendation. Customer to call whirlpool for help with repair. will return with fill tube. Office to reschedule. Sr#7730931047; ordrng 1 W10701614 (Fill tube and heater assembly)

"Arrived on site for washer not spinning out load. Ran diagnostics got valve temp 0-4 , 7-5 unable to reach max rpm, 7-1 shifter fault . Recommend replacing actuator ,gearcase and valve .

Arrived onsite for washer not operating at all. Upon arrival found unit control was receiving but not sending voltage throughout.

"Arrived on site to inspect unit for not draining, upon inspection found a new disposal on unit, knocked out drain cap and helped customer with disposal. The main assembly for dispenser door was broken. Ordering part. Office to reschedule ; ordrng 1 3369505 (det.disp.actuator)"

Arrived on site to diagnose a refrigerator that is leaking. Found drain line frozen over. Thawed line and all is working properly at this time. No leaks were found at time of service.

"Arrived on site to inspect unit for not spinning, upon inspection found the unit running but the relay did not click when a large load was detected. Replaced control and tested unit with a large load, no problems found. Complete"

Arrived on site to diagnose a dryer that is not completely drying. Found no failures to unit at this time and advised customer on best cycles and options for best results.