Near Round Rock, TX 78664
Cliff
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF767SDEM01
Arrived on site to diagnose a refrigerator that is not cooling properly. Tested unit and found defrost failure due to shorted user interface. Replaced user interface and tested unit. Found all is working properly at this time. Homeowner will manually the refrigerator for 24 hours prior to resuming operation.
Near Lakeway, TX 78734
Brandon
Job Details:
08/03/2020
DISHWASHER WHIRLPOOL WDT750SAHZ0
"Arrived on site for customer customer complaint of unit starting by itself and sensor light would blink, found failed control boards, I replaced controls and ran diagnostic test cycle, unit passed all tests."
Near Austin, TX 78747
Kevin
Job Details:
08/03/2020
WASHER WHIRLPOOL WTW4850HW1
Near Manor, TX 78653
Scott
Job Details:
08/03/2020
DRYER WHIRLPOOL WED4850HW0
Arrived on site for no heat dryer . Found one of the wires on motor harnes wasnÂ’t connected in molex . Reinserted wire in plug . Unit is now heating properly . No lint build up at time of service . Job complete .
Near Austin, TX 78731
Paul
Job Details:
08/03/2020
MICROWAVE KITCHENAID KEMS308SSS04
Arrived onsite for a wall oven that is not heating properly. Ms stated that it will heat but it will never reach set point temp. I tested the oven and found the bake element not heating. I explained to the customer that it could be a burned out bake element or a defective control.Call complete.
Near Pflugerville, TX 78660
Wesley
Job Details:
08/03/2020
MICROWAVE WHIRLPOOL WMH31017HS2
Arrived onsite and found all operating as designed but fan is burnt out causing overheating problem. Ordering fan to repair. ; ordrng 1 W11252443 (FAN)
Near Georgetown, TX 78628
Cliff
Job Details:
08/03/2020
DRYER LG DLEX8377NM
Arrived on site to diagnose a dryer that is making unusual noise. Tested unit and found roller broken. Replaced roller and tested unit. Found all is functioning properly at this time. Also performed full clean out for dryer.
Near Georgetown, TX 78628
Lou
Job Details:
08/03/2020
REFRIGERATOR KITCHENAID KRMF706EBS01
"Arrived on site to inspect refrigerator UI not responding and the unit turning off/on. Upon further inspection, I found the unit operating as designed. I placed the unit in diagnostics and when I checked the thermistor in step 1, the unit failed to respond. I took the unit out of diagnostics and then the unit shut down. I cycled the power to the unit and it would not start up, but it was getting voltage. I could hear the 3 way valve attempting to get into,home position, but wouldnÂ’t. I contacted the previous tech that was having similar issues previously and after performing several voltage checks and everything checking good the unit intermittently would power up and begins cool with no issues. But when I cycled the power one more time while testing voltage to the inverter board, the unit failed to come back on but still had voltage. Finally after a while, the unit came back on and began to cool. Previous tech advised that the 3 way valve solenoid
Near Martindale, TX 78655
Robert
Job Details:
08/03/2020
WASHER MAYTAG MHW5630HC0
Arrived on job for complaints of no water. Found switch for water level not working properly. Replaced switch and test.
Near Driftwood, TX 78619
Robert
Job Details:
08/03/2020
WASHER MAYTAG MVWB865GC0
Arrived on job for complaints of damaged lid. Confirmed damage and replaced lid. No leaks detected at time of service
Near Round Rock, TX 78665
Paul
Job Details:
08/03/2020
RANGE WHIRLPOOL WEG745H0FH0
Arrived onsite for a range with the LF burner not working. Ms stated the burner will light but if itÂ’s turned off after it lights and turned back on it doesnÂ’t light again. I tested all the burners and found the burner cap on the LF burner not fitting correctly causing a floating flame when it would light. I swapped the LF and RF burner caps and tested the burners. Both burners had good flames. I found a draft coming from the AC vent in the kitchen causing lighting issues when the air was blowing. I showed this to ms and advised turning the microwave fan on low to prevent the draft. I showed ms how this would allow the burner to light correctly every time. The unit is working as designed. Call complete.
Near Leander, TX 78641
Lou
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRX735SDHZ02
"Arrived on site to inspect refrigerator water dispenser not working. Upon further inspection, I tested the dispenser and water barely came out. I removed the filter and placed my bypass in the filter head and retested and unit continued to dispense slowly. I removed and replaced the filter head/reservoir and placed a new filter in and tested and it failed. I placed the customers universal brand filter in and the unit is operating as designed. No water leaks observed during service, job completed."
Near San Marcos, TX 78666
Noah D
Job Details:
08/03/2020
WASHER WHIRLPOOL WTW8500DW5
"Arrived on site to inspect washer for error codes during operation, upon inspection found a miscommunication error code, control was swapped out recently, replaced console to have matching programs. Job complete"
Near Round Rock, TX 78681
David S
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF767SDEM01
Arrived on site for ice build up behind the crisper drawer. I inspected the unit and work area. I found the fresh food evaporator covered in ice. I put the unit into diagnostics mode and verified that the freezer and fresh food fans are activating. I tested the defrost bi metal and showed a good reading. I put the unit through test 38 and forced a defrost. The heating element in the freezer came on as designed. There is a miss communication between the UI control W11092503 and the fresh food evaporator thermistor w11033168. .; ordrng 1 W11092503 (panel-ui)
Near Lockhart, TX 78644
Leonardo
Job Details:
08/03/2020
DISHWASHER BOSCH SHX7PT55UC/04
Arrived on site to found new control board damage. Will order control board again 00752741 office to reschedule ; ordrng 2 00752741 (CONTROL MODULE )s
Near Buda, TX 78610
Leonardo
Job Details:
08/03/2020
RANGE KITCHENAID KFED500EBS03
Arrived on site replaced board. Replaced board test unit and unit test good job complete.
Near New Braunfels, TX 78130
Noah D
Job Details:
08/03/2020
WASHER WHIRLPOOL MHW5630HC
"Arrived on site to inspect washer for leaking out of front, Upon inspection found the drawer leaking, ordering drawer and dispenser. Office to reschedule; ordrng 1 W11169072 (DRAWER ) and 1 W11437244 (DISPENSER)"
Near Kyle, TX 78640
Leonardo
Job Details:
08/03/2020
OVEN WHIRLPOOL WEG750H0HZ0
Arrived on site to test unit for unit not staying on. Test unit and Lund unit not connected to WiFi. Advised customer unit needs to be connected to WiFi to get software updates. Helped customer connect unit and unit did software update job complete
Near Manchaca, TX 78652
Leonardo
Job Details:
08/03/2020
RANGE WHIRLPOOL WFG505M0BS3
Arrived on site to test unit for oven light not turning on. Tested unit found relay on control board not closing causing light not to turn on. Ordering part W11126814(control board).. ; ordrng 1 W11126814 (CONTROL BOARD)
Near Buda, TX 78610
Leonardo
Job Details:
08/03/2020
RANGE WHIRLPOOL WFG525S0HZ1
"Arrived on site to test unit for not igniting. Tested unit found bad oven bake ignitor. Replaced ignitor. Tested unit, unit works good to 350 degrees. Job complete."
Near Austin, TX 78752
Scott
Job Details:
08/03/2020
DRYER WHIRLPOOL WED8000DW4
"Arrived on site for dryer making a lot of noise when tumbling. Found front bottom left hand side dented and pushed up ,causing housing to push against blower wheel . Reshaped cabinet , unit is now operating normally now . No lint build up at time of service . Job complete ."
Near Austin, TX 78731
Paul
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF954CIHZ00
Arrived onsite for a refrigerator that is not holding temps and is very hot around the sides. I asked the customer if the unit had been making ice ok and ms stated yes. I temped the FC and the RC and found the FC at 1 degrees and the RC at 36 degrees. Ms stated some things would freeze on the second shelf in the rear. I found the product pushed against the rear wall and explained the the product shouldnÂ’t be pushed back past the shelves because it will restrict air flow and cause products to freeze. I went over install instructions with the customer because the unit is in a cabinet and it is tight on both sides restricting air flow to the condenser and fan. I explained this was causing the excessive heat under the cabinet above the refrigerator. Ms stated they would get the cabinet repaired to resolve this. The unit is working as designed. Call complete.
Near Dripping Springs, TX 78620
Robert
Job Details:
08/03/2020
OVEN WHIRLPOOL WFG320M0BS3
Arrived on job for complaints of oven not working. Found the regulator for oven in off position. Switch to on position now oven lighting.
Near Round Rock, TX 78681
David S
Job Details:
08/03/2020
REFRIGERATOR KITCHENAID KRMF706ESS01
Near Lockhart, TX 78644
Richard
Job Details:
08/03/2020
WASHER WHIRLPOOL WFW9400SW03
Arrived onsite for the washer leaking water into the tub while turn off. During testing found that the water valve was not closing all the way alllowing water to leak into the tub . Replaced water valve assembly and washer tested good and no leaks .
Near Lampasas, TX 76550
Al
Job Details:
08/03/2020
WASHER WHIRLPOOL WFW95HEDC0
Called Whirlpool Tech line and spoke with AUSTIN SR#7728360529Clean washer is once a month or 30 loads is recommended by whirlpool.Customer says she only cleans unit when she thinks about it.Ran a quick wash cycle and unit tested as designed.Cleared error code and even all the customer to wash a load of towels on quick wash and unit tested as designed without errors.AUSTIN recommended no parts needed .All water lines were dry at the time of service.Job complete
Near Austin, TX 78717
David S
Job Details:
08/03/2020
OVEN WHIRLPOOL WFG715H0ES0
"Arrived on site for range not heating properly. I inspected the unit and work area. I found the light bulb housing stuck, I was able to remove the housing and found the bulb to be bad, I checked the light bulb socket and found the socket receiving 120v. I reinstalled the bulb housing and I ensured it is easily removable. I did a temp test on the unit and found preheat got to 370. I opened the door and let the temp drop. The unit cycled on and heated to temp 370 and cycled off the heat. The unit cycling with a 20 degree difference. The unit is operating as designed.
Near Austin, TX 78717
David S
Job Details:
08/03/2020
REFRIGERATOR KITCHENAID KRSC500ESS00
"Arrived on site for fridge door not sealing properly. I inspected the unit and work area. I found both doors sealing properly. I felt proper resistance when trying to open the door. When closing the door it is being pulled into fridge as designed. The unit is operating as designed, and the doors are sealing as designed. Job complete. No water leaks detected."
Near Kyle, TX 78640
Richard
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRS325SDHZ01
Arrived onsite for the refrigerator ice maker not making ice. During testing found that the ice maker was not plug in. Plug ice maker harness in and ice maker tested fine it went through a full cycle and it filled with water. Complete called tech line Sr # 7728460155.
Near Waco, TX 76706
Jonathan M
Job Details:
08/03/2020
DRYER WHIRLPOOL CEM2745FQ0
"Arrived on site for dryer thatÂ’s not heating. Inspected unit and work area. Removed bottom panel and tested thermal cut off, fuse, element, and high limit thermostat. All checked good. Tested voltage at terminal block and found 120 V from L1 to neutral and L2 to neutral and 204 V from L1 to L2. I called commercial tech line to try to figure out how to jump the machine without using coins and ask for any other information. I spoke to Jerry and he had me check wiring at the timer. All checks ran good. He advised me to have the customer give us coins to run the cycle because he advised everything seemed to check out. The customer old coins out of the coin box and started up the unit. Unit is heating and working as designed. I advised the customer that If they have problems with the unit completely drying their clothes, their vent hose is an extended vent hose and may cause issues with drying completely. Advised them to shorten the hose
Near Austin, TX 78702
Jacob
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRS576FIDM00
Arrived onsite for unit not dispensing water with a new water filter. Took out water filter. Tested unit. Water was coming out with good pressure. But customer says after a few days the water will trickle once again. Filter housing needs to be changed out.
Near Hewitt, TX 76643
Tyler
Job Details:
08/03/2020
WASHER WHIRLPOOL WTW5000DW3
"Arrived on site for washer tripping breaker. Upon arrival I immediately saw the washer was connected to a gfci outlet. I called whirlpool tech line and spoke with Steve (sr# 7728465555), who instructed I use an extension cord to be able to connect the washer to a dedicated non-gfci outlet and run an automatic test on the unit. He said that if all ran well and no error codes were present with the unit after test then unit would be fine and that the gfci would need to be replaced with either a high grade gfci or simply a regular outlet. After running test there were no error codes that popped up.unit is functioning as it was designed. Instructed customer to have an electrician to swap out gfci for better version or plain 120v outlet. Call complete"
Near Temple, TX 76501
Tyler
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF535SWHZ01
Arrived on site to install new filter head as well as filter plate assembly after installing new parts I retested the entire filter system and everything is working perfectly there were no leaks before during or after repair and customers are ready to use their water dispenser whenever they need to. Call complete
Near Copperas Cove, TX 76522
Al
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WSF26C3EXY01
Arrived to install previously ordered part.Removed and replaced the valve.Reassembled and unit tested as designed.All water lines were dry at the end of service.Job complete
Near Austin, TX 78717
David S
Job Details:
08/03/2020
DRYER MAYTAG MGDB765FW0
"Arrived on site for dryer not drying properly. I tested the unit and found the igniter coming on and the flame lighting but only staying lite for about 30 seconds and lighting again 2 minuets later. I replaced the thermal cut off, flame sensor, coils and control. I tested the unit again and got the same result. I removed the vent from the unit and found they cycles for heating are working properly. I spoke with the customer about the air flow being restricted. I found out they had a company come out and clean the vents but never checked the vent exit in the roof, I let the customer know if they never cleared the vent exit itÂ’s self there is likely a restriction or build up there cause I hen dryer to not heat properly. Job complete."
Near Marble Falls, TX 78654
James
Job Details:
08/03/2020
WASHER MAYTAG MVWB835DC4
"Arrived on site and tested operation. Found left hinge has failed and caused door to break at corner. Also found fault for water temp sensor. Found sensor to have failed. Also found gear case has failed and is making a grinding noise while spinning and agitating. Unit will need new gear case, slider, lid, hinge and valve to repair. ; ordrng 1 W10734521 (slider) and 1 W10811956 (GEAR CASE) and 1 W11256781 (lid) and 1 W11401116 (HINGE)"
Near Manor, TX 78653
David S
Job Details:
08/03/2020
RANGE WHIRLPOOL WFE525S0HS1
Arrived on site for washer angle having no power. I inspected the unit and work area. I found mai harness burnt at the junction. I inspected the power cable and it showed good continuity in the wiring. I replaced the main harness. I powered the unit on and tested all functions. The unit is operating as designed. Job complete.
Near Austin, TX 78730
David Z
Job Details:
08/03/2020
DISHWASHER KITCHENAID KUDE70FXSS4
Arrived on site to diagnose dishwasher with control locked console. Unlocked console using the unlock button. Showed customer which key to hold down to unlock console. Ran diagnostic cycle and confirmed all is good. Call complete.
Near Lorena, TX 76655
Tyler
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRS571CIHZ01
"Arrived on site for replacement of freezer door, icemaker, & jumper wire. After inspecting original diagnosis of freezer door I found that the freezer door itself is functioning fine also the icemaker does appear to be able to call for water and harvest just like it should and after running diagnostics on both the icemaker in the thermistors in the freezer in the fridge I found that everything was functioning as designed. The problem I found that was causing the freezer to allow too much cold air into the refrigerator and freezing everything on the fresh fruit side was due to the fact that the dampener motor located in the fresh meat section was bad and at certain points it would get stuck open and then another situations it would be stuck closed and not allowing the cold air to fluctuate through the unit as it should. At this point in time the dampen the motor will need to be replaced in order to allow proper air fluctuations between freezer and fr
Near Austin, TX 78723
Jacob
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRX735SDHV01
Arrived onsite for unit over freezing. Looked at unit. Found that freezer door was not shutting properly. Ordered parts. Rescheduled with customer. ; ordrng 2 W11265130 (slide)s and 1 WP12466115SP (light switch)
Near Austin, TX 78759
Wesley
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF757SDHZ00
Near Austin, TX 78759
Wesley
Job Details:
08/03/2020
FREEZER WHIRLPOOL KUDF204ESB00
Arrived onsite and found ice build up in Evap drain pan. Melted ice and advised customer to let unit thaw for 24 hrs. Advised customer on repair
Near Austin, TX 78748
Kevin
Job Details:
08/03/2020
DRYER WHIRLPOOL WED4850HW
"Arrived on site and inspected dryer and found it is heating properly but there is no airflow, removed vent hose from dryer and airflow has returned. Home was the model and washer and dryer sat unused. Vent to exterior is clogged or stuck. No further repair is needed at this time, job complete"
Near Austin, TX 78753
Scott
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL ED5PVEXWS00
"Arrived on site for unit temps running erratically. Found thermostat failing ,also start relay would click a couple times before it would kick on compressor . Replaced both thermostat and relay . Unit is starting and cooling properly now . No water leaks detected at time of service.job complete ."
Near Austin, TX 78723
Jacob
Job Details:
08/03/2020
DISHWASHER WHIRLPOOL WDT750SAHZ0
Arrived onsite for top rack adjusters broken. Saw broken adjusters and stoppers. Called landlord. Got authorization to replace parts. Replaced both parts. Tested unit. Unit test good. No leaks at this time. Job complete
Near West, TX 76691
Jonathan M
Job Details:
08/03/2020
DISHWASHER MAYTAG MDB4949SHZ0
Arrived on site for dishwasher that still not washing dishes. Inspected unit and work area. Opened up inner door and found motor connector removed from control. Attempted to reattach but connector would not clip. Removed connector and found the control side connector broken. Replaced control and reconnected wash motor harness. Unit is now working as designed. Call complete.
Near Austin, TX 78738
Luis
Job Details:
08/03/2020
REFRIGERATOR KITCHENAID KURR104ESB00
"Arrived on site for no cool. Found control on and off buttons unresponsive,removed ui control found harness and wires corroded that caused wire to break in harness,called tech support
Near New Braunfels, TX 78130
Noah D
Job Details:
08/03/2020
ICE MACHINE KITCHENAID KUIX305ESS1
"Arrived on site to inspect icemaker for overproducing, upon inspection found the ice bin thermistor shorted. Replaced thermistor and tested. No problems found. Complete"
Near Austin, TX 78759
Wesley
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL ED5RHEXNL00
"Arrived onsite and found unit fill arm popped out of place. Reinserted. Advised customer on repair
Near Georgetown, TX 78626
Cliff
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRS315SDHM01
Arrived on site to replace previously ordered part for the refrigerator. Inspected unit prior to replacing part and found all parts and components fully functional and ice container full. Advised homeowner when fan was not running the cold air in the refrigerator section froze water reservoir preventing proper operation. Now that cooling has been restored properly reservoir has thawed out ice and water are working. No further repairs are needed and no leaks were found at time of service.
Near Copperas Cove, TX 76522
Al
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF767SDEM00
"Arrived to inspect massive ice buildup in the fresh food section behind the deli drawer.Confirmed the complaint and due to the size of the blockage the customer will need to defrost unit (defrost waiver signed).Unit will require a harness to complete the repair.
Near Kingsbury, TX 78638
Richard
Job Details:
08/03/2020
REFRIGERATOR FRIGIDAIRE LGHB2867PFHA
"Arrived onsite for the refrigerator with frost build up around the ice maker compartment. Upon inspection found that the parts that were ordered were the wrong parts. Also found that the UI was not working properly. Ordering ice maker housing and UI, clear siliconed. After replacing the ice maker house will need to apply the clear silicone around the housing to fill the gaps and to prevent air getting into housing. Office to reschedule ; ordrng 1 242058230 (user interface) and 1 242093501 (housing) and 1 SILICONE (CLEAR SILICONE )"
Near Austin, TX 78717
David S
Job Details:
08/03/2020
DISHWASHER WHIRLPOOL WDF590SAJM0
Arrived on site for dish rack not coming out properly and squeaking. I inspected th unit and work area. I found the door getting stuck on the right side. I gained access to the leveling feet and found the unit out of level. I leveled the unit and the door closed as designed. I inspected the tracks and adjusters for the middle rack. I found the track and adjusters not formed properly. I am ordering both tracks and he adjuster kit. ordrng 1 W10712395 (adjuster) and 2 WP3385089 (track)s
Near Austin, TX 78759
Wesley
Job Details:
08/03/2020
RANGE KITCHENAID KSIB900ESS2
Sockets had already been sent to customer. Used customer stock to update socket. Advised customer on repair. Sabbath mode does not change function per user manual specifications. Advised customer to request ; ordrng 1 W11100619 (cntrl-elec)
Near Austin, TX 78704
Kevin
Job Details:
08/03/2020
WASHER WHIRLPOOL MVW7230HW0
"Arrived on site and replaced missing rotor screw diagnosed on previous visit, after replacement ran automatic test cycle and found everything is operating normally. No water leaks detected at time of service, job complete"
Near Manor, TX 78653
David S
Job Details:
08/03/2020
RANGE AMANA AER6303MFB2
Arrived on site for range not heating up. I inspected the unit and work area. I found the bake element not coming on. I inspected the main harness and found the connection for the bake element was broken. I replaced the main harness. I powered the unit back on and tested all operations. The unit is operating as designed. Job complete.
Near Austin, TX 78759
Paul
Job Details:
08/03/2020
REFRIGERATOR JENN-AIR JS42NXFXDE01
Arrived onsite for a refrigerator with the FC lights not working. I found the left side upper LED module defective. I replaced the LED module and found all the lights working as designed. Call complete.
Near Austin, TX 78728
David Z
Job Details:
08/03/2020
MICROWAVE WHIRLPOOL WOC54EC0HS03
Arrived on site to continue diagnosis on lamp not coming on in microwave. Replaced bulb and MW control board. Retested and light is now on and working as designed. Call complete.
Near Georgetown, TX 78628
Lou
Job Details:
08/03/2020
WASHER WHIRLPOOL MVWB765FW2
"Arrived on site to inspect washer noises. Upon further inspection, I placed the unit in diagnostics showing error code F7E9. Cleared the code and continued with testing. I manually tested heavy agitation per the error code recommendations and the unit operated as designed. I could hear a thumping noise while it was agitating. I tilted the unit back and found a large amount of gearcase oil on the side panels, drain pump, harness shield. I removed the rotor and found gearcase oil on the underside the rotor and on the slider. No water leaks observed during service, job completed."
Near Austin, TX 78731
Paul
Job Details:
08/03/2020
DISHWASHER KITCHENAID KDTE704DSS1
Arrived onsite for a dishwasher to replace the previous diagnosed parts. I replaced the vent and vent harness. I tested the dishwasher in diagnostics and found it working as designed. There were no water leaks present at the time of service.
Near Kyle, TX 78640
Kevin
Job Details:
08/03/2020
DRYER MAYTAG MGDX655DW2
"Arrived on site and found dryer vent to exterior of home was attempted to be cleared by a service since the previous visit. Still found no airflow took picture of airflow meter and showed customer what good airflow feels like by removing the vent hose from the rear of the dryer and asking them to put their hand in the lint screen receiver. Cleaning company will need to return and completely correct airflow,
Near The Hills, TX 78738
Brandon
Job Details:
08/03/2020
ICE MACHINE KITCHENAID KUIS18NNZB0
"Arrived on site for customer complaint of unit not starting cleaning cycle, I showed customer how to run cleaning cycle, standby mode and press and hold clean button, unit tested good."
Near Kingsbury, TX 78638
Richard
Job Details:
08/03/2020
WASHER AMANA NTW4516FW2
Arrived onsite for the washer not cycling properly. Ran diagnostics and found error code for a long fill. During testing found that the cold water valve was not working properly. Inspected the valve and found a lot of debris inside of it. Water valve assembly will need to be replaced.ordering parts and office to schedule. .; ordrng 1 W11210463 (valve)
Near Austin, TX 78738
Luis
Job Details:
08/03/2020
ICE MACHINE UNKNOWN RF15IR
"Arrived on site for no water. Powered unit on water entering reservoir,pump powered on water dispensing over evaporator plate"
Near Austin, TX 78737
Luis
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRS321SDHZ05
Arrived on site for damaged door. Replaced damaged fresh food door and nameplate checked door seal good.
Near Temple, TX 76502
Tyler
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRX986SIHZ00
Arrived on site to install a filter head as well as a freezer if that motor assembly and a washer to raise the front left door after installing parts I was able to test entire unit out and they were no longer any leaks from the filter head the top left door closes perfectly now and million hits the pivot like it should and the freezer and fresh food second sections are at Temp just as they should be. Call complete
Near Manor, TX 78653
David S
Job Details:
08/03/2020
RANGE WHIRLPOOL WFE525S0HS1
Arrived on site to for range not having power. I inspected the unit and work area. I found the main harness burnt at the junction. I tested the power cable for continuity. The power cable is good. I replaced the main harness which came with the junction. I powered the unit on and tested all operations. The unit is working as designed. Job complete.
Near New Braunfels, TX 78132
Noah D
Job Details:
08/03/2020
REFRIGERATOR KITCHENAID KRFF507ESS01
"Arrived on site to inspect fridge for humming noise, upon inspection found the evap fan hitting ice in pantry, will need to defrost evap before servicing.
Near San Marcos, TX 78666
Noah D
Job Details:
08/03/2020
REFRIGERATOR KITCHENAID KRFC704FPS03
"Arrived on site to inspect fridge for freezing food, upon inspection found the freezer at-5 while set for 5 degrees, will need new thermistor due to resistance readings. Office to reschedule ; ordrng 1 W10797088 (THERMISTOR)"
Near The Hills, TX 78738
Brandon
Job Details:
08/03/2020
OVEN WHIRLPOOL KEBC177KSS05
"Arrived on site for customer complaint of unit not heating, found failed thermostat, I replaced thermostat, unit tested good.
Near Horseshoe Bay, TX 78657
James
Job Details:
08/03/2020
DISHWASHER KITCHENAID KDTE334GBS0
Arrived on site and tested operation. Found proper voltage to unit but no operation from control. Found low voltage transformer on control has failed. Installed new control and tested operation. Unit tests good. Job complete
Near Del Valle, TX 78617
Jacob
Job Details:
08/03/2020
WASHER WHIRLPOOL WFW560CHW1
Arrived onsite for unit making noise during spin cycle. Tested unit. In drain and spin. Found no issues for noise. Tested unit in a quick wash cycle. Did not get any sounds. Gave tenant instruct on using the unit for proper wash cycles. No leaks at this time. Job complete
Near Georgetown, TX 78628
Cliff
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL KRFC604FSS03
Arrived on site to diagnose a refrigerator that is not running at all. Tested unit and found fans and lights operational but compressor not functioning at all. Replaced Orion board due to internal short. Tested unit and found all is functioning properly at this time. No leaks were found at time of service.
Near Buda, TX 78610
Brandon
Job Details:
08/03/2020
MICROWAVE WHIRLPOOL WMH31017FS0
"Arrived on site for customer complaint of microwave not heating, found failed magnetron
Near Austin, TX 78723
Jacob
Job Details:
08/03/2020
OVEN WHIRLPOOL WOS51EC0HS01
Arrived onsite for unit not responding to touch when unit gets hot. Tested unit. Found that UI panel would be un responsive. Replaced UI panel console. Tested unit. Unit test good. No issues at this time. Job complete
Near Dripping Springs, TX 78620
Robert
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL KFIV29PCMS02
Arrived on job for complaints of leaks found refrigerator drain blockage. Removed blockage.
Near Georgetown, TX 78628
Cliff
Job Details:
08/03/2020
WASHER MAYTAG MVWB765FW3
"Arrived on site to replace previously ordered parts for washer. Replaced rotor, stater, and clutch. Tested unit and found all is functioning properly at this time. No leaks were found at time of service."
Near Lakeway, TX 78734
Brandon
Job Details:
08/03/2020
FREEZER WHIRLPOOL WZF34X16DW04
"Arrived on site for customer complaint of unit frosting in lower section of unit. Found door was all the way adjusted to the lowest position but gasket was not sealing due to extreme bend/warp on bottom of door, ordering door. ; ordrng 1 CNOTE (OFFICE TO RESCHEDULE ) and 1 W10673692 (dor-fmd)"
Near Austin, TX 78703
Leonardo
Job Details:
08/03/2020
COOKTOP KITCHENAID KGCC566RWW04
Arrived on site to test unit for no spark. Tested unit found burnt out harness and spark module. Replaced harness and spark module. Tested unit left front ignitor not sparking will be needing LF orifice holder assembly. Ordering part#WPW10128445(LF orifice holder assembly).; ordrng 1 WPW10128445 (LF ORIFICE HOLDER)"
Near Leander, TX 78641
Lou
Job Details:
08/03/2020
COOKTOP KITCHENAID KICU509XBL00
"Arrived on site to inspect cooktop error codes. Upon further inspection, I found the unit display showing F47 error code. Per the service pointer #W10556232A, I removed and replace the module and programmed it code 23. Tested each burner and the unit is operating as designed. Job completed."
Near Liberty Hill, TX 78642
Lou
Job Details:
08/03/2020
DISHWASHER WHIRLPOOL WDF330PAHS3
"Arrived on site to inspect dishwasher leaking water. Upon further inspection, I found the water turned off. I placed the unit in diagnostics showing error code F6E4. Cleared the code and continued with testing. When I turned the water back on, water came flowing into the tub and I had not started testing. I stopped diagnostics and turned the drain pump on and turned the water off. I removed and replaced the inlet valve and found a lot of debris in the old valve screen. Placed the unit in diagnostics and tested and the unit is operating as designed. I had to adjust the leveling of the unit as it was installed tilted forward. Re-leveled the unit and checked the water level in the tub (photo) and it is good. No water leaks observed at the end of service, job completed."
Near Kingsland, TX 78639
James
Job Details:
08/03/2020
WASHER WHIRLPOOL WFC8090GX0
Arrived on site and tested operation. Found ui lights up but has blank display. Unplugged to reset unit and found ui now working. Attempted to run diagnostics and found buttons not responding to allow entry. Unit will need new door to repair. Office to schedule return services due to expart door; ordrng 1 W11280150 (door)
Near Georgetown, TX 78633
Lou
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRX988SIBM03
"Arrived on site to inspect refrigerator temps. Upon further inspection, I found the RC evaporator with ice built up on it. Customer advised they removed a large amount with a hair dryer. I checked the FC evaporator and it had a good frost pattern. I removed the ice and removed and replaced the evap motor harness and tested. Unit is cooling as designed. No water leaks observed during service, job completed."
Near Austin, TX 78728
David Z
Job Details:
08/03/2020
DISHWASHER WHIRLPOOL WDT710PAHZ1
"Arrived on site to diagnose dishwasher they was not filling. Performed diagnostic on unit . Found no error codes. Can hear inlet valve trying to let water in. When I checked after fill cycle there was barely any water in. Replaced fill valve and retested. Unit still isnÂ’t filling. Checked hoses and found unit has a separate hose running under the sink and is not tied into the hot water line, the valve at the wall also has an anti hammer valve. Customer advised to resolve issue with builder since no kinks are found in line and unit is working as designed. Call complete."
Near New Braunfels, TX 78130
Leonardo
Job Details:
08/03/2020
OVEN WHIRLPOOL WOS72EC0HS01
Arrived on site to replace door and hinges. Was able to unlock the door but door came right off and damaged the trim and floor. Took picture of damaged will need to order new trim WPW10327377 and replaced console and when removing the blue cover found part was damaged. Will order new console W11428583 office to reschedule ; ordrng 1 W11428583 (CONSOLE ) and 1 WPW10327377 (TRIM )
Near Austin, TX 78702
Luis
Job Details:
08/03/2020
FREEZER WHIRLPOOL WZF79R20DW00
"Arrived on site for unit powering itself off. Diagnosed a defective main control,installed a new main control powered unit on unit working as designed."
Near Lockhart, TX 78644
Richard
Job Details:
08/03/2020
FREEZER WHIRLPOOL WRF535SWHZ04
Arrived onsite for the refrigerator leaking water in the freezer section. During testing found that the ice maker fill tube was stuffed behind the Evaporator cover causing the leak. Took ice maker out and was able to pull the ice maker fill tube out from behind the cover and put it in the correct spot. Ice maker tested good and filled with water and leak is gone. Complete
Near Austin, TX 78741
Leonardo
Job Details:
08/03/2020
MICROWAVE WHIRLPOOL WMH53521HZ0
Arrived on site to test unit for unit not working. Test unit and found fan blowe rnot coming on when unit heating. Found bad control board
Near Austin, TX 78748
Kevin
Job Details:
08/03/2020
DRYER MAYTAG MEDX655DW1
"Arrived on site and inspected dryer and found start switch has fallen back into console. Disassembled dryer and reset start switch and it is now operating properly, job complete"
Near Austin, TX 78746
Kevin
Job Details:
08/03/2020
DRYER WHIRLPOOL WED9200SQ0
"Arrived on site and replaced thermal fuse diagnosed by previous technician after replacement dryer is heating normally again and will run properly. job complete"
Near Pflugerville, TX 78660
David S
Job Details:
08/03/2020
DRYER FRIGIDAIRE FFSG5115PW0
Near Austin, TX 78704
Jacob
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL KRFC300ESS03
Arrived onsite for handle being loose. Looked at unit. Handle was a bit loose. Tightened screws to handle. Tested unit. No issues at this time. Job complete
Near New Braunfels, TX 78130
Leonardo
Job Details:
08/03/2020
OVEN WHIRLPOOL WOD51EC0HS01
Arrived on site to test unit for panel turning on and off. Found bad console replaced console test unit and unit test good. Advised customer to make sure they connect unit to WiFi job complete.
Near Dripping Springs, TX 78620
Robert
Job Details:
08/03/2020
RANGE GE P2S930SEL4SS
Arrived on job for complaints of unable to convert to LP gas. Found orifice damaged on front left burner. Will need holder to complete. ; ordrng 1 WB16X28867 (ORIFICE HOLDER )
Near Kingsbury, TX 78638
Richard
Job Details:
08/03/2020
WASHER MAYTAG MVWC565FW0
Arrived onsite for the washer making a noise during spin cycle. Replaced spin basket that was order and washer tested good and no leaks detected complete
Near Leander, TX 78641
Lou
Job Details:
08/03/2020
DISHWASHER WHIRLPOOL WDT970SAHZ0
"Arrived on site to inspect dishwasher powering on but not working. Upon further inspection, I found water in the tub and I attempted to turn the drain pump on but the unit failed. I placed the unit in diagnostics and when I pressed start, the console failed to respond. I removed and replaced the console and retested and the control failed to send voltage to the motor. I removed and replaced the main control and retested. The unit is operating as designed. No water leaks observed during service, job completed."
Near Spicewood, TX 78669
Brandon
Job Details:
08/03/2020
RANGE KITCHENAID KFDC506JSS00
"Arrived on site for customer complaint of right rear burner not lighting, found orifice is not the right size, ordering conversion kit off of service pointer. ; ordrng 1 W11238042 (LP CONVERSION KIT )"
Near Driftwood, TX 78619
Robert
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRS588FIHZ00
Arrived on job for complaints of rattling noise. Removed back and found tube touch from added pad to remove noise. No leaks detected at time of service.
Near Austin, TX 78750
David Z
Job Details:
08/03/2020
REFRIGERATOR WHIRLPOOL WRF736SDAW14
"Arrived on site to diagnose refrigerator that was not cooling well in RC and not making ice. Performed diagnostic and checked FC Evap. FC Evap has a good frost pattern and freezer items were cold. Found already ice buildups all over the Evap cover, and around the RC vents, and the Evap motor was not running. Melted down ice with a steamer and replaced the Evap fan motor. Used truck stock permagum to seal the channels on the Evap frame by the RC vents to,stop ice buildup. Reassembled and all is now working as designed and unit is cooling.
Near Georgetown, TX 78628
Lou
Job Details:
08/03/2020
DISHWASHER MAYTAG MDB4949SHB0
"Arrived on site to inspect dishwasher not functioning. Upon further inspection, I found the unit console not responding. When I moved the junction box, the lights on the console came on, but I could not get the unit into diagnostics. I checked voltage at the control and got 122V. I tested the motor, element, drain pump, door switch, sensor and all were good. I checked continuity at the console harness and it was good. I removed and replaced the main control and tested and unit is operating as designed. No water leaks observed during service, job completed."