We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Austin, Texas 78744
James K
Job Details:
07/09/2025
"Arrived on site for unit dispensing water slow. Upon arrival, proceeded to remove filter and black sediment coming out of filter. Continued to clear out water line until water was clear. Advised maintenance superintendent to install new filter since now unit is flushed. Customer agreed. Unit is functioning as designed. No parts needed. No water leaks detected at this time"
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Austin, Texas 78744
James K
Job Details:
07/09/2025
"Arrived on site for unit making thumping noise when spinning. Upon arrival, found front right roller was faulty. Proceeded to replace 4392067 repair kit. Tested unit and now unit is functioning as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Austin, Texas 78744
James K
Job Details:
07/09/2025
"Arrived on site for unit not cooling. Upon arrival, ran diagnostics and found compressor not running. Proceeded to expose back panel and found start device connector disconnected. Plugged connector back in. Re tested and now compressor came on with no issues. Unit is functioning as designed. No water leaks detected at this time. No parts needed"
We serviced a
KITCHENAID DISHWASHER
Model KUDS30FXSS2
Near Austin, Texas 78746
Joe Z
Job Details:
07/09/2025
"Arrived on site for unit not operating/ washing. Upon arrival, ran diagnostics and get error codes. F6-E4 inlet water float switch open ,F10-E1 dispenser electrical problem ,F6-E1 low or no water,F6-E6 In coming water is under 84 degrees. Found a piece of plastic under float switch. Removed debris and test unit. Unit filled and began washing correctly. Observed dispenser operates correctly . Canceled unit and drains correctly.Unit is operating as designed. No leaks present. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Austin, Texas 78744
James K
Job Details:
07/09/2025
"Arrived on site for unit not starting. Upon arrival, when holding start, display will not count down. Proceeded to replace W11565030 latch. Started unit and now unit starts as normal. Ran diagnostics and passed with no issues. Ran quick wash and passed with no issues. Unit is functioning as designed. No water leaks detected at this time"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Austin, Texas 78747
James K
Job Details:
07/09/2025
"Arrived on site for unit not washing. Upon arrival, found wash motor energized but not running. Proceeded to replace W11613479 sump assy. Ran diagnostics and passed with no issues. No water leaks detected at this time"
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS3
Near Austin, Texas 78744
James K
Job Details:
07/09/2025
"Arrived on site for unit tripping breaker when oven is in use. Upon arrival, proceeded to replace W11447783 bake element and WPW10583047 broil element. Ran Broil until unit reached 200F. Then proceeded to run Bake at 500F for 30 minutes and breaker did not trip. Service pointer applied. Unit is functioning as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model wrs331sdhm06
Near Austin, Texas 78744
James K
Job Details:
07/09/2025
"Arrived on site for unit tripping breaker. Upon arrival, found unit is cooling properly. Checked breaker box and found non GFCI breaker for that circuit. Continued to run extension cord to GFCI outlet and unit tripped within 5 seconds of startup. Proceeded unplug each connector one by one on the control and found connector that controls the heater circuit to trip. Ordering W11650659 heater assy. No water leaks detected at this time. No parts replaced. Front office agreed to reschedule July 17th ; ordrng 1 W11650659 (Heater assy)"
We serviced a
MAYTAG WASHER
Model MHW5500FW1
Near Austin, Texas 78732
Scott
Job Details:
07/09/2025
"Arrived on site for washer throwing error codes .found door locked . Ran diagnostics got 9-1,3-1,5-2. Ran diagnostics, drain pump motor sounds very loud and not pumping any water . Found motor has failed . Replaced drain pump WPW10605427. Ran diagnostics, all checked normal. No water leaks detected at time of service. Job complete"
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Salado, Texas 76571
Tyler
Job Details:
07/09/2025
"Arrived on site for washer, that customer stated had an f9e1 error code on arrival. Confirmed issue, but upon further inspection found drain pump at first would appear to drain and function. But after filling tub up multiple times and uh, stressing up the drain pump, I found it starting to pump less water each time. It was used the longer it was used. I am ordering W11578225 pump i rescheduled the customer for 07-16-25.; ordrng 1 W11578225 (Pump)"
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS08
Near Hutto, Texas 78634
David Z
Job Details:
07/09/2025
"Arrived on site to diagnose microwave sparking on use. Examined unit and found microwave has excessively oil contamination, resulting in saturated wire sheath on the transformer allowing voltage to arc / fry the diode. Advised customer with this much saturation we would need to replace the HV system, which would exceed the cost of a new unit. Customer will replace. Called findings into safety."
We serviced a
WHIRLPOOL RANGE
Model WFGS5030RZ0
Near Round Rock, Texas 78665
David Z
Job Details:
07/09/2025
"Arrived on site to diagnose range with constantly clicking igniter. Tested unit and confirmed a nonstop clicking when plugged in at all. Outlet shows good. Found of the 5 switches on the harness, 2 of them are broken completely, and one is split causing the valve to not actuate it properly. Ordering switch harness to resolve. Office to schedule when we can get part. ; ordrng 1 W11727166 (Switch Harness)"
We serviced a
WHIRLPOOL WASHER
Model WET4027HW1
Near Pflugerville, Texas 78660
David Z
Job Details:
07/09/2025
"Arrived on site to diagnose washer not progressing in cycles. Customer said unit seems to fill, sit and then drain. I tested the unit and found it was filling excessively full. Checked codes and found long fill code. I blew through the pressure hose and could hear the air coming out before the tub. I diassembled the rear of the unit and traced the failure to a rupture in the hose right above the rear cover. I replaced the power harness to resolve. Ran a normal cycle and verified proper operation. Repair completed. Parts used - W11417071."
We serviced a
MAYTAG WASHER
Model MVW5035MW1
Near Round Rock, Texas 78665
David Z
Job Details:
07/09/2025
"Arrived on site to diagnose washer with issues banging on spin. Found issue is a continuation of previous visit. I checked basket, suspension, gearcase and level of unit and found the only item in need of attention was the level. Unit had to be leveled on both axis. There is no play in the basket at all, suspension is in working order. Tested unit and verified no further banging or vibration. Advised customer of normal operations and behaviors of unit. Everything working as designed. Call completed."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Round Rock, Texas 78665
David Z
Job Details:
07/09/2025
"Arrived on site to follow up on sealed system repair. Tapped system and found 30psi present. Evacuated system. Replaced drier and nitrogen tested after disconnecting compressor. Found no oil in system. Replaced compressor and added sleeve to condenser line, pressure tested. Found no leaks. Vacuumed down system and charged. Verified no leaks and system started cooling. Parts used - W11506635, WPW10143759, W11578205."
We serviced a
KITCHENAID COOKTOP
Model KCGC506JSS00
Near Leander, Texas 78641
Lou
Job Details:
07/09/2025
"Arrived on site to inspect cooktop burner not igniting properly. Upon further inspection, the customer advised that the burner has never ignited properly. I tested all of the burners and found that the front right burner takes too long to ignite. I removed the burnerhead and adjusted it and retested, and the unit is operating as designed. No gas leaks detected during service, job completed."
We serviced a
WHIRLPOOL COOKTOP
Model WCE77US6HS00
Near Lago Vista, Texas 78645
Lou
Job Details:
07/09/2025
"Arrived on site to inspect cooktop burner not operating. Upon further inspection, I tested all of the burners and found the back right burner center element is not turning on. Also found that all of the knobs stems are badly worn, and the front left burner knob is jammed onto the switch stem. Once I was able to remove the knob, I found the knob stem was broken, which is why it was jammed onto the switch stem. I gained access to the rear right burner element and switch and found the element had shorted, and the switch was shorted. I tested voltage and found 246V going to the outer element and no voltage to the inner element. I removed and replaced the switch and element and retested, and the unit is operating as designed. I recommended that the customer contact the manufacturer to get the knobs replaced. Job completed. W10857622, W10823727"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS335SDHM07
Near Round Rock, Texas 78665
Daniel A
Job Details:
07/09/2025
"Arrived on site to inspect refrigerator making noise. Upon further inspection, the customer informed me that the refrigerator would make a loud noise for hours at a time. Temperatures measured -1 degree FC 37 degrees RC. The customer provided a recording, and I found the sound to be coming from the evaporator fan. I gained access to the evaporator and found evidence of the water flowing out of the ice maker fill tube. I added a piece of fill tube extension to the chute and retested the ice maker fill. The ice maker is now filling as designed. The refrigerator is operating as designed. The customer showed me that there was slight damage to the back cover that may have happened in shipping. The back panel damage is not causing any issues. No water leaks observed during service."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS01
Near Round Rock, Texas 78681
Daniel A
Job Details:
07/09/2025
"Arrived on site to inspect refrigerator not cooling properly. Upon further inspection, I checked temperatures and measured 45 degress RC and 2 degrees FC. All fans are operating as designed. I gain3d access to the RC evaporator, and I found that it was not defrosting properly. I checked the thermistors from the control and all thermistor are in range. I ran a forced defrost and found that it was operating as designed. To correct the issue, I set the fridge to standard defrost and raised the front of the fridge slightly as I found it leaking forward. Proper temperature will return in the next 24-48 hr. No water leaks observed dueing service."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Austin, Texas 78717
Daniel A
Job Details:
07/09/2025
"Arrived on site to inspect refrigerator, making strange noise and power cycling occasionally. Upon further inspection, the customer provided a video of the issue, and I found the noise to be coming from the evaporator fan. I also suspected that based on the symptoms that the fan was failing internally and shorting. I replaced the evaporator fan and reassembled the unit. Th unit is operating as designed. No water leaks observed during service. W11578030"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near New Braunfels, Texas 78130
Tim M
Job Details:
07/09/2025
"Arrived on site to inspect unit for damage. Upon arrival customer presented issue, console is cracked. Documented damage in SD. Replaced console (W11413566) and tested, unit is now functioning and appears as designed, job complete."
We serviced a
KITCHENAID OVEN
Model KOES530PSS00
Near Briarcliff, Texas 78669
Leonardo
Job Details:
07/09/2025
"Arrived on site to inspect unit for door not closing properly. Tested unit and found the left hinge not seated correctly in the receiver. Removed the door, repositioned it, and secured it properly. Tested unit and confirmed door is closing as designed. Job complete."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Dripping Springs, Texas 78620
Leonardo
Job Details:
07/09/2025
"Arrived on site to inspect unit for not washing or dissolving soap intermittently. Upon arrival, the customer had already run the unit, and it was working correctly at this time. Checked for error codes and found none. Placed the unit into diagnostic mode, and the unit operated as designed. Contacted Techline and ran additional tests but was unable to duplicate the issue. Per Techline, advised the customer to contact Customer Care for further assistance. Job complete. SR#7741796106"
We serviced a
WHIRLPOOL MICROWAVE
Model KOCE500ESS06
Near Dripping Springs, Texas 78620
Leonardo
Job Details:
07/09/2025
"Arrived on site to inspect unit for reported fire on the waveguide cover. Found damaged waveguide cover. Removed the waveguide cover and took pictures to document the issue and for submission to Techline. Observed some white powder inside the cavity of the unit. Contacted Techline for further guidance. Per Techline, cleaned the cavity thoroughly, and the white powder was successfully removed. Replaced the waveguide cover as instructed. Ran a test by heating water for 2 minuteswater heated properly with no sparks or malfunctions. Unit is operating as designed. Job complete SR#7741946526"
We serviced a
WHIRLPOOL WASHER
Model WFW6620HC2
Near Leander, Texas 78641
Daniel A
Job Details:
07/09/2025
"Arrived on site to inspect washer making a loud noise during fill and leaving cloths wet on delicate cycle. Upon further inspection, I found that the washer was quite unlevel and the weight was not evenly distributed on the 4 legs. I leveled and tighted the jam nuts on the feet. I then ran component testing, and found that cold water valve was seizing and making a loud squealing noise. I replaced the cold valve and ran an automatic test and the washer is operating as designed. I informed the customer that the delicate cycle is the minimum spin speed and may not be sufficient to dry clothes depending on the load type and size. No water leaks observed during service. W11688995"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Leander, Texas 78641
Lou
Job Details:
07/09/2025
"Arrived on site to inspect washer noises. Upon further inspection, the customer advised that the unit is making the same 'screeching' noise as before, and it only happens in the spin cycle. I placed the unit in diagnostics, showing no error codes and tested. The unit operated as designed until the spin cycle, at which time, in the beginning, as the basket was starting to ramp up in speed, it began to make a screeching, metal on metal noise. As the basket spun faster, the noise stopped. The customer also advised that the unit intermittently gets off balanced as well. Due to the previous repairs not resolving the issue, I removed and replaced the gearcase, cam, and belt and calibrated the unit. Retested in diagnostics, and the unit is operating as designed. No water leaks observed during service, job completed. W11449840, W11239857, W10721967"
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Round Rock, Texas 78665
Daniel A
Job Details:
07/09/2025
"Arrived on site to install previously diagnosed and ordered parts per previous technician. I installed the rotor and stator and the slider. I calibrated and tested the machine, and the machine is now operating as designed. No water leaks were observed during service. W10734521 W10915701 W10915700"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78724
Justin
Job Details:
07/09/2025
"Arrived on site to repair previously diagnosed issue gearcase replacement. Replaced gearcase, cam, actuator and belt. When putting new belt on noticed noise happening when turning cam. Ran test cycle noise is still happening. Called previous tech who diagnosed also called PR supervisor recommended try replacing motor. So ordering motor, gearcase and new cam return tech trying replacing motor before anything else. Office to reschedule ; ordrng 1 W11454372 (Gearcase) and 1 W10721967 (Cam) and 1 W11686050 (Motor)"
We serviced a
JENN-AIR REFRIGERATOR
Model JF42NXFXDE05
Near Canyon Lake, Texas 78133
Tim M
Job Details:
07/09/2025
"Arrived on site to replace previously diagnosed part. Upon arrival replaced FC door (W10782358) and inspected, unit is now functioning as designed, no leaks detected, job complete."
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Kyle, Texas 78640
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for constant knocking noise, tested unit found motor mount loose causing blower wheel to rub against housing, secured mount and tested, unit is now running as designed job complete no parts installed"
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Kyle, Texas 78640
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for door not closing properly, tested unit found door latch needs a hood push to close, adjusted catch and tested, door is now closing properly job complete no parts installed"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Seguin, Texas 78155
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for fan not turning off, tested unit found really loud, replaced and tested unit is now running as designed, explained to customer that is is normal for the fan to run up to 8 hours after the cycle completes if the door is not open, unit is now running as designed no leaks detected job complete installed W11682810"
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near New Braunfels, Texas 78132
Tim M
Job Details:
07/09/2025
"Arrived on site to test unit for lid not unlocking. Upon arrival customer stated lid does not lock. Verified issue, latch actuates multiple times but does not latch. Replaced latch (W11700916) and ran a test cycle, all components are properly engaging and unit is now running as designed, no leaks detected, job complete."
We serviced a
WHIRLPOOL RANGE
Model WFE550S0LZ3
Near New Braunfels, Texas 78130
Tim M
Job Details:
07/09/2025
"Arrived on site to test unit for no power. Upon arrival customer stated she started a bake cycle and the unit shut off almost right away. Found breaker tripped, reset breaker and started a bake cycle, on the third relay click when switching back to bake the unit tripped. Contacted SAFETY to document SR#7741892118, per SAFETY they advise going with any repair that I see fit. Replaced bake element (WP9755770) and broil element (W10856603). Started a bake cycle at 500?, unit reached set temp with no tripping breaker. Allowed unit to cycle for an additional 15 minutes, breaker is not tripping and unit is now running as designed. Advised customer to continue running bake cycle for an additional 90 minutes to ensure proper burn off and relay conditioning. Job complete."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS07
Near New Braunfels, Texas 78130
Tim M
Job Details:
07/09/2025
"Arrived on site to test unit for no power. Upon arrival customer stated unit shut off and would not turn back on. Had the outlet replaced and circuit checked with no issues, breaker does not trip. Verified issue, unit is receiving proper power but there are no functions present during test. Tested unit, found orion control is not sending voltage to the main control. Replaced orion control (W11664342) and main control (W11567409) as precautionary. Applied power to the unit, all functions have returned to the unit. Compressor engaged and unit is beginning to cool. Unit is now running as designed, no leaks detected, job complete."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT531HAPM0
Near New Braunfels, Texas 78130
Tim M
Job Details:
07/09/2025
"Arrived on site to test unit for no power. Verified issue, no LEDs illuminated. Outlet is receiving proper voltage. Inspected terminal block and found black wire has been removed from wire nut due to wire nuts being too small. Replaced wire nuts with proper size and secured connection. Applied power and tested, all functions have returned and unit is now running as designed, no leaks detected, no parts installed, job complete."
We serviced a
MAYTAG WASHER
Model MVW6230HW0
Near New Braunfels, Texas 78132
Tim M
Job Details:
07/09/2025
"Arrived on site to test unit for no water detected. Upon arrival customer stated during a cycle unit will start a fill but wont progress due to error stating water is not detected. Entered diagnostics, found F8E1 (long fill) error code stored. Inspected valves and found some buildup. Ran a test cycle and valves have lost pressure. Replaced valve (W11220230) and control (W11543994) as precautionary. Ran a calibration cycle successfully. Ran a test cycle with all components properly engaging. Advised customer to run a clean washer cycle. Unit is now running as designed, no leaks detected, job complete."
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPS00
Near Canyon Lake, Texas 78133
Tim M
Job Details:
07/09/2025
"Arrived on site to test unit for not clear ice. Upon arrival customer stated after the sealed system repair was complete, unit began to produce slightly foggy ice, its gotten worse over time. Entered diagnostics and manually tested unit, valve would not engage. Cycled power and went through manual diagnostics again, valve still would not engage. Replaced valve (W10897719), unit now fills properly. Recirculating pump attempted to engage but would not. Replaced recirculating pump (W11542867) and drain pump (W11542868). Ran a manual test cycle, unit fills, recirculates but does not drain. Suspecting an issue with the logic. Ordering main control, rescheduled for 07/16.; ordrng 1 W11034363 (Main control) and 1 W11325205 (UI)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ12
Near Seguin, Texas 78155
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for not dispensing properly, tested unit found no issues with the dispensing ice function explained to customer that sometimes the ice is further back and it will take a little time for it to get moved towards the front, unit is running as designed no leaks detected job complete no parts installed"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP560HAMZ1
Near Kyle, Texas 78640
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for not working properly, tested unit found wash motor not engaging, replaced sump and tested unit is now running as designed no leaks detected job complete installed W11613479"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Marion, Texas 78124
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for not working properly, tested unit found latch will not open, had to break it out, replaced latch and control as precautionary and tested unit is now running as designed no leaks detected job complete installed W11742939, W11513248"
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Buda, Texas 78610
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for pump not turning off, replaced control per service pointer and tested unit is now running as designed no leaks detected job complete installed W11607637"
We serviced a
WHIRLPOOL DRYER
Model WED5050LW1
Near Marion, Texas 78124
Andrey
Job Details:
07/09/2025
"Arrived on site to test unit for water in unit, tested unit found condensation developing inside, explained to customer that do to the high humidity temp in laundry room should not be below 75 degrees, advised customer to shut vent, handle on the door is also broken, will not stay in, will need to replace handle to fix issue, ordering handle rescheduled for 7/17; ordrng 1 W10861225 (Handle)"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ11
Near Spicewood, Texas 78669
Luis
Job Details:
07/09/2025
"Arrived on site. Found new source of water leak,condensation around inlet air flow vent casuing water to drip down icemaker housing and into bottom of fresh food secrion,cleared water adjusted gasket on damper and between icemaker vent.Found small amount of ice in container ran forced harvest icemaker taking long harvest cycle,replaced icemaker,ran harvest test passed checked water connections at valve no leaks during icemaker fill and dispenser test. W11548540"
We serviced a
WHIRLPOOL WASHER
Model WFW86HEBC0
Near Austin, Texas 78735
Scott
Job Details:
07/09/2025
"Arrived on. Site for washer leaking around door area. Removed top and outer bellow spring . Bellow in good shape , no signs of hoses leaking . All water connections dry. Found buildup unrer glass on door and bottom of door gasket , cleaned debir out . . Ran diagnostics. Could duplicate any leaking . Did advised to clean under door glass . Collected. 162.36 autho 9TV999. Job complete"
We serviced a
KITCHENAID REFRIGERATOR
Model KUID508HPS01
Near Georgetown, Texas 78633
Tyler
Job Details:
07/09/2025
"Arrived on-site for ice machine, not making it ice. On arrival confirmed issue and upon further inspection found unit was not getting any water into the reservoir tank. I then found that the water valve W1089779 was bad. I replaced it and found ice machine working as designed with no leaks. Informed customer to allow twenty four hours unit to fill bin Call complete."
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD708MSS01
Near Georgetown, Texas 78628
Brandon B
Job Details:
07/09/2025
"Arrived on-site for unit making hissing sound. Found fc was 24 degrees and rc was 41 degrees. Evaporator has no frost pattern and the compressor is running. No error code. I'm ordering W11557671 compressor, W11629714 evap, dye drier wpw10143759, w11506635 service port and 2 hrs sstech for return visit. Office to reschedule. ; ordrng 1 W11557671 (Compressor) and 1 wpw10143759 (Dye drier) and 1 w11506635 (Service port) and 1 2hrssstech (Ss tech) and 1 W11629714 (Evap)"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Austin, Texas 78721
Matthew
Job Details:
07/09/2025
"Arrived onsite to replace faulty compressor. Replaced compressor, drier and access valve. Pulled vacuum and held. Charged per spec and tested. Unit is now functioning properly. Advised customer to give 24-48hrs for temperature to stabilize. Job complete"
We serviced a
WHIRLPOOL DRYER
Model WED9550WW2
Near Killeen, Texas 76542
Robert
Job Details:
07/09/2025
"WED9550WW2 Arrived on site for a dryer with error code f70. On arrival, I didn't see the error code, but I did notice that clients are not cleaning lint trap causing a large amount of lint in the lint trap. I cleaned as much as i could then i tested the ventilation to clients home and it's in terrible condition I recommend client to contact a professional to clean the ventilation to home no parts needed product is working as its designed."
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Belton, Texas 76513
Robert
Job Details:
07/09/2025
"WFES3530RS0 Arrived on site for a range tripping breaker. On arrival I verified issue I replaced contol board, bake, and broil element. I removed ground wire preheated to five hundred degrees temperature reached without tripping breaker. I rewired ground back on and preheated to five hundred degrees temperature reached without tripping breaker. I checked polarity, voltage, and amp draw all readings are correct product works as it's designed. I recommend client to contact home builder if range trips the breaker again so they can replace the gfci breaker. Calling whirlpool safety Sr #"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Fort Cavazos, Texas 76544
Robert
Job Details:
07/09/2025
"WRS321SDHZ11 Arrived on site from previous visit to install parts. On arrival I installed motor,ui control, and door ice further issues refrigerator had was a defective board. I ordered control board office to reschedule client for the soonest availability please. Returning parts just in case needed no water leaks visible from main water supply. ; ordrng 1 W11742389 (Control board)"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Fort Cavazos, Texas 76544
Robert
Job Details:
07/09/2025
"WTW4957PW0 Arrived on site for a washer with the pump running. On arrival I verified long drain a defective control board. I replaced control board, calibrated then tested product is working as its designed no water leaks visible from main water supply."
We serviced a
MAYTAG WASHER
Model MVWB835DC4
Near Hewitt, Texas 76643
Jonathan M
Job Details:
07/09/2025
Arrive downside to install previously diagnosed part. Inspected unit and work area. I replaced the wire harness and found that the gear case had been installed improperly. I tried to adjust the gear case but found that the upper part of the drive shaft bowed when trying to push the drive shaft through enough to rotate it. I also found that the rotor screw was completely seized in the drive shaft on the bottom and could not be removed. I drilled out the screw and replaced the gear case and slider as well. I calibrated the unit and ran it through a diagnostic cycle. The unit began to work and operate as designed. Call complete
We serviced a
KITCHENAID MICROWAVE
Model KMBP100ESS20
Near Austin, Texas 78739
Leonardo
Job Details:
07/09/2025
Arrived on Side to replace harness replace harness test unit by heating water for two minutes twice you need it correctly no burning smell Job complete.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Temple, Texas 76504
Jonathan M
Job Details:
07/09/2025
Arrived on site for a dishwasher that is not washing dishes. Inspected unit and work area. I ran the unit through diagnostics and found an F4 E3 (wash motor not running) error code. I ran the unit through an auto test and found the wash motor would not run. I replaced the wash motor assembly and tested the unit. The unit began to work and operate as designed with no leaks present during operation. Call complete. W11613479.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78748
Scott
Job Details:
07/09/2025
Arrived on site for a washer having control issues . Went to apt with maintenance person . Washer not matching modle &ser dispatched. Tenant has had not had any issues with washer . Maintenance not sure where washer is . Will need to reschedule when found . Job complete
We serviced a
JENN-AIR OVEN
Model JJW6024HL0
Near Austin, Texas 78746
Joe Z
Job Details:
07/09/2025
Arrived on site for console not responding. Upon arrival found issue is intermittent. Found cable loose. Secured cable on console. Unit is operating as designed. Job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAMS0
Near Austin, Texas 78727
Miguel
Job Details:
07/09/2025
Arrived on site for dishwasher not starting. Confirmed start button and other buttons due not respond. Removed door panel. Verified power to control. Replaced main control. Ran automatic test cycle to confirm operation. Unit now working. Call complete. W11613566
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Austin, Texas 78727
Miguel
Job Details:
07/09/2025
Arrived on site for drain pump running. Unit 6213. Confirmed drain pump starts as soon as it's plugged in. Checked pump and wiring. Checked pressure hose. Per Service Pointer - W11766193. Replaced main control. Recalibrated and ran automatic test cycle. All working. Call complete. W11607637
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD618ESS01
Near Spicewood, Texas 78669
Luis
Job Details:
07/09/2025
Arrived on site for no lights. Diagnosed a defective led module per service pointer removed all leds installed updated led modules all leds working as designed. W11632139
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ3
Near Austin, Texas 78746
Joe Z
Job Details:
07/09/2025
Arrived on site for not draining . Upon arrival ran diagnostics and get F9-E1. Test unit. Can hear slight buzzing from drain pump. Replaced drain pump W11412291. Test unit and is operating as designed. No leaks present Job complete
We serviced a
WHIRLPOOL WASHER
Model MHW5630HC2
Near Austin, Texas 78703
Scott
Job Details:
07/09/2025
Arrived on site for outer tub spring off . Checked bellow and all looks normal. Ran diagnostics and got both door lockerror codes only .replaced bellow spring . Ran diagnostics test and all checked normal. No water leaks detected at time of service. Collected 162.36 autho 9M4UNM. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM00
Near Round Rock, Texas 78681
Miguel
Job Details:
07/09/2025
Arrived on site for refrigerator not freezing properly. Read freezer at 14f and refrigerator at 28f. Removed rear cover and found dye leaking. Removed evaporator cover. Found it coming from the evaporator and compressor. Recovered existing refrigerant. Removed filter drier and copper tubing ended up breaking off. Took pics. Called tech support. They will be submitting for review. Advised customer they will be contacted within 5 business days. Sr#7741945839
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM08
Near Austin, Texas 78724
Justin
Job Details:
07/09/2025
Arrived on site for unit making noises. Inspected unit found sound only happens when compressor is on. Inspected compressor and found compressor line vibrating on a piece of m3tal. Used permagum to stop noise. Unit is now functioning properly and as designed to. No leaks present at this time job completed
We serviced a
WHIRLPOOL DISHWASHER
Model WDF331PAHS1
Near Austin, Texas 78724
Justin
Job Details:
07/09/2025
Arrived on site for unit not turning on. Inspected unit found no led lights on at controlnand could not enter service diagnostics. Checked power at control and got 120 volts unit needs a new control. Replaced control and tested unit is now functioning properly and as designed to. No leaks present at this time job completed. No one on site for signature
We serviced a
WHIRLPOOL RANGE
Model WFC150M0EW4
Near Bastrop, Texas 78602
Justin
Job Details:
07/09/2025
Arrived on site for unit not turning on. Inspected unit found nothing working checked voltage found terminal block chared and arched. Took picture upload to sd. Unit will need new terminal block ordering part return set8/16; ordrng 1 WPW10245259 (Terminal block)
We serviced a
JENN-AIR RANGE
Model JGS1450FS0
Near Austin, Texas 78704
Scott
Job Details:
07/09/2025
Arrived on site for upper door vent peeling . Replaced scoop W11251351. Ss trim is no longer avalable . Only color is now black . No gas leaks detected at time of service. Job complete
We serviced a
JENN-AIR DISHWASHER
Model JDB8200AWP3
Near Spicewood, Texas 78669
Scott
Job Details:
07/09/2025
Arrived on site for upper rack falling down . Found right hand upper rail welds had failed . Replaced both upper rails .per service pointer . No water leaks detected at time of service. Job complete
We serviced a
WHIRLPOOL OVEN
Model WFG505M0MS0
Near Round Rock, Texas 78665
David Z
Job Details:
07/09/2025
Arrived on site to diagnose oven with door closing issues. Found the outer door glass had come free of the lower brackets. Found the brackets were bent and needed adjustment. Adjusted and reseated brackets and glass. Tested and verified proper fitment. Repair completed.
We serviced a
WHIRLPOOL MICROWAVE
Model MH1170XSS0
Near Cedar Park, Texas 78613
Daniel A
Job Details:
07/09/2025
Arrived on site to inpsect microwave bot heating. Upon further inpsection. I found that the magnetron was faulty and had a cracked magnet. I also found that the capacitor leads were worn and not making good contact. I replaced the capacitor and the magnatron and reasembled and tested the unit. The unit is now operating as designed. W10850446 W10754299
We serviced a
KITCHENAID COOKTOP
Model KCGS556ESS06
Near Austin, Texas 78736
Leonardo
Job Details:
07/09/2025
Arrived on site to inspect unit for left rear burner and center burner not igniting or taking too long to ignite. Tested unit and immediately found both burners had incorrect burner caps. Repositioned the burner caps to the correct burners. Tested unit and confirmed all burners are now igniting properly. Job complete.
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Cedar Creek, Texas 78612
Justin
Job Details:
07/09/2025
Arrived on site to repair previously diagnosed issue unit needs new sump and motor. Replaced sump and motor and tested unit is now functioning properly and as designed to. No leaks present at this time job completed
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Dripping Springs, Texas 78620
Leonardo
Job Details:
07/09/2025
Arrived on site to test unit for not heating. Ran diagnostics and found F7E1 error indicating no heat during cycle. Pulled unit out to test the heating element and found the element reading open. Replaced the heating element and tested the unit by running a diagnostic cycle. The heating element is now activating and getting hot. No leaks present at this time. Job complete.
We serviced a
KITCHENAID MICROWAVE
Model KMMF330PSS00
Near Austin, Texas 78759
Wesley
Job Details:
07/09/2025
Arrived onsite and found f7e9 error ongoing and vent motor operating as though the actuator can't find position. Sr#7741945892 spoke with Nathan at techline who explained that they are working on a not yet published service pointer and updated part numbers for the ACU and UI specifically to resolve the f7e9 error code when there is not an obstruction or loose feedback wire. Verified no obstruction or feedback warie issue. Office to reschedule pending the service pointer being published. No parts. No signer available
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Austin, Texas 78732
Wesley
Job Details:
07/09/2025
Arrived onsite and found unit operating with obstructed drain motor. Replaced the motor due to potential wear. Unit is now operating as designed. Advised customer on repair. W11462456.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ01
Near Austin, Texas 78732
Wesley
Job Details:
07/09/2025
Arrived onsite and replaced the freezer door to repair the broken integral wiring harness in order to restore ice function. Unit is now operating as designed. LW11202405
We serviced a
WHIRLPOOL ICE MACHINE
Model WUI95X15HZ00
Near Austin, Texas 78731
Wesley
Job Details:
07/09/2025
Arrived onsite and replaced valve formlow flow and thin production. Adjusted thickness to max. Advised the customer on repair. W10881366
We serviced a
KITCHENAID REFRIGERATOR
Model KSSC48QMS01
Near Austin, Texas 78732
Wesley
Job Details:
07/09/2025
Arrived onsite for above temp. Showing 30f and 50f respectively. Unit is trying to cool. Has good airflow but incomplete frost pattern. The sealed system has been serviced but it may have been recharged and not repaired in accordance with manufacturing standards by another company. Ordering sealed system repair. 3hrs no parts. ; ordrng 1 W10841139 (Compressor) and 1 WP2306094 (Evap) and 1 WPW10143759 (Uv drier) and 1 Tj90SF8404 (Access port)
We serviced a
JENN-AIR MICROWAVE
Model JMW2430LL04
Near Austin, Texas 78731
Wesley
Job Details:
07/09/2025
Arrived onsite for broken cook tray. Replaced cookery to repair. Unit is now operating as designed. All checks good. W11373838
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RV00
Near Georgetown, Texas 78633
Brandon B
Job Details:
07/09/2025
Arrived on-site for icemaker making noise. I couldn't replicate the noise but the customer said it happens when ice is harvesting. I'm ordering W11692161 ice maker for return visit. No parts used. Office to reschedule. ; ordrng 1 W11692161 (Icemaker)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT108FFDM04
Near Austin, Texas 78753
Andrew R
Job Details:
07/09/2025
Arrived onsite for icemaker not making ice. Customer stated it is making ice but when inspecting i found the fill tube too short and not seated into the icemaker. Customer stated main issue was the RC section was getting moisture. I found the gasket to have a gap and I reformed it. Skeptical of it returning back to place as it was hard to reform correctly. Will order a gasket just in case and ordering a fill tube to fix the fill issue. Ordering W11030683 GSKT RC and WPW10496649 FILL EXT. RS FOR 07-22-25.; ordrng 1 W11030683 (GSKT RC) and 1 WPW10496649 (Fill Ext)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ02
Near Georgetown, Texas 78628
Brandon B
Job Details:
07/09/2025
Arrived on-site for icemaker not working. Verified the issue. I removed the cover on the icemaker and the jumper fell out. I plugged it back in and the tray filled and icemaker began it's cycle. Also found the gasket for the icedoor had fallen off. Gasket wasn't damaged so I put it back on. Unit is operating as designed. No parts used.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM13
Near Austin, Texas 78754
Andrew R
Job Details:
07/09/2025
Arrived onsite for previously diagnosed parts. I replaced both the RC and FC doors. Unit now looks as designed. Call complete. No leaks. Installed LW11258450 RC DOOR AND LW11258441 DOR FIP.
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Austin, Texas 78754
Andrew R
Job Details:
07/09/2025
Arrived onsite for previously diagnosed parts. Same issue occurring since past 2 calls. Call is still covered as previous issue wasn't solved. I replaced the motor and blower wheel is good. Tested the unit and unit operates as designed. Call complete. Installed WPW10396039 MOTOR.
We serviced a
JENN-AIR RANGE
Model JGRP536HM05
Near Austin, Texas 78704
Matthew
Job Details:
07/09/2025
Arrived onsite for Right front burner not igniting. Disassembled and found igniter wasn't cracked and not grounding properly. Replaced igniter. Tested and unit is now functioning properly. Job complete
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Austin, Texas 78759
Wesley
Job Details:
07/09/2025
Arrived onsite for unit not completing a cycle. F3e1 error saved. Repqlced the c9ntrol for c9 tenuous drain symtpom. Pressure system faults. All checks good. Calibrated unit. W11608056
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED2CHQXKB05
Near Austin, Texas 78752
Andrew R
Job Details:
07/09/2025
Arrived onsite for unit not dispensing ice. I found the motor to check good. When pulling off the faceplate I found the bracket holding the ice door switch to be broken and causing the flapper to not make connection. Verified switch was good by pressing it and motor actuated. Unit needs a new face bracket. Ordering WP2180226 Bracket to continue with repair and RS for 07-17-25. ; ordrng 1 WP2180226 (Bracket)
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM06
Near Austin, Texas 78723
Andrew R
Job Details:
07/09/2025
Arrived onsite for unit not dispensing water and not cooling. Spoke with PR and found un8t was tripped and the fan motor not operating. Unit has good frost pattern. I replaced the fan motor and it's now operating as designed. I checked the rear and found no pressure in the line. Maintenance will need to check the wall valve as I can hear the fridge valve working but not pulling water. No leaks. Call complete. Installed WP2315549 EVAP FAN. Also got photo of lease date for warranty.
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Jarrell, Texas 76537
Brandon B
Job Details:
07/09/2025
Arrived on-site for unit tripping the breaker. I verified the issue. I replaced the bake element and heated 500 without the ground strap. Reheated with the ground and unit didn't trip the breaker. Max amp draw was 19. Power is good at the tblock. Sr 7741894870 called safety. Usedw11182108
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW1
Near Georgetown, Texas 78628
Brandon B
Job Details:
07/09/2025
Arrived on-site for washer with no power. Found unit has power. No error codes. Customer said that unit only works on towel setting. I couldn't replicate the issue. I replaced the encoder(w11627516) and tested unit. Everything is working as designed.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Andice, Texas 78628
Chris
Job Details:
07/09/2025
Arrived onsite to inspect dishwasher not circulating water upon further inspection ran diagnostics found f4e3 motor failure replaced pump & motor W11613480 ran diagnostics again cleared code unit is working as designed no leaks observed during service
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Andice, Texas 78628
Chris
Job Details:
07/09/2025
Arrived onsite to inspect dishwasher not cleaning upon further inspection ran diagnostics found f4e3 bad replaced motor w11613479 ran test cycles unit is working as designed no leaks observed during service
We serviced a
KITCHENAID RANGE
Model KFDC506JSS01
Near Marble Falls, Texas 78654
Chris
Job Details:
07/09/2025
Arrived onsite to inspect oven preheat light not changing from red to white during preheat upon further inspection tested unit bake cycles & found the unit is working as designed
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Marble Falls, Texas 78654
Chris
Job Details:
07/09/2025
Arrived onsite to inspect washer not filling with water in certain cycles upon further inspection ran diagnostics found no errors also did a factory reset advised customer on cycle settings verified unit is working as designed on all cycles no leaks observed during service
We serviced a
KITCHENAID OVEN
Model KOES530PSS00
Near Austin, Texas 78701
Matthew
Job Details:
07/09/2025
Arrived onsite to replace wire harness. Replaced and tested. Unit is now functioning properly. Job complete.
We serviced a
JENN-AIR COOKTOP
Model JGC3536GS01
Near Austin, Texas 78721
Matthew
Job Details:
07/09/2025
Found burner cap not properly seated causing longer ignition. Secured cap and tested. Unit is responding and igniting properly. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM08
Near Austin, Texas 78758
Miguel
Job Details:
07/09/2025
Moved to 266. Vacant apartment. Waited till until finished defrost.. compressor started and fans started. No noise heard. Tried again and unit starts sounds normal. Moved refrigerant lines innback away from cover just in case. Call complete. No parts.
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Pflugerville, Texas 78660
David Z
Job Details:
07/09/2025
Updated model and serial. Arrived on site to diagnose washer constantly running drain. Verified when plugged in drain is running. Replaced control to resolve. Unit falls under service pointer W11766193. Verified unit working properly with new Control. Parts used - W11607637.
We serviced a
WHIRLPOOL MICROWAVE
Model WMH31017HS10
Near Killeen, Texas 76549
Robert
Job Details:
07/09/2025
WMH31017HS10 Arrived on site from previous visit to install part. On arrival I installed the diode then I tested with a cup of water product is working as its designed. Calling whirlpool safety Sr # 7741861490
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ01
Near Copperas Cove, Texas 76522
Robert
Job Details:
07/09/2025
WRT112CZJZ01 Arrived on site for a refrigerator not cooling. On arrival I verified issue I checked the start device and found it had failed I replaced and checked for frost pattern product is working as its designed no water leaks visible from main water supply.