"Arrived on site. Removed compressor cover found damaged fill tube line,replaced valve and repaired line,installed a new water line customer provided. Turned on water source no leaks,ran icemaker through a cycle water filled icemaker.

Arrived on site to test unit for unit not washing and unit leaking. Test unit and found unit filling with water but not washing and unit leaking from sump gasket due to one lock broken. Test unit and unit test good job complete no leaks present at this time.

"Arrived on site to inspect range burner not working. Upon further inspection, I tested the cooktop and found all burners except the back left burner operating as designed. I inspected the switch and it is operating as designed. I had the customer sign the waiver of damages from removing glass cooktop and raised the cooktop and inspected the element and found it burnt.

"Arrived on site for no cool. Gained access to compressor compartment found uv leaking from condenser line,cleaned and brazed line,vacuumed system down unit kept vacuum recharged system to manufacture spec powered unit on checked low side pressure good.

Arrived on site for no ice. Power cycled unit drain pump powered on then shut unit off diagnosed a defective external drain pump.

"Arrived on site to inspect wall oven not working. Upon further inspection, the customer advised they did a self clean on the unit and the lower unit no longer heats. I pulled the unit form the wall and tested the TOD (thermostat) and found it open. Tested the bake and broil elements and they are good. I removed and replaced the TOD and tested the lower unit and it is operating as designed. I placed the unit back in the wall and retested the upper and lower ovens and the unit continues to operate as designed. Job completed."

Arrived on site for dishwasher not drying dishes. Upon arrival ran diagnostics and found no error stored. Ran diagnostics cycle and found heater would come on as designed. Found amperage to heater was .98 amp and steady. Found rinse aid dispenser functioning during tests and relaxing when power was applied. Instructed customer on whirlpool use and care and tips on how to get best results from dry cycle. Unit functioning as designed. Call complete

"Arrived on site to inspect dishwasher not heating. Upon further inspection, I tested the element and its within ohms reading. Tested voltage to the element and it is not getting voltage. I attempted to test the TOD (thermostat) and due to it having shrink cover on the connectors, I was unable to test at the part itself. I tested from the control and found it open. I attempted to locate the part in the ge parts breakdown and was unable to find it. I am ordering a PARTS RESEARCH-TOD, float switch, and will return with the main control kit and element. Office to schedule return service due to availability of parts. I advised my customer that I would get them a quote for repairs once I return with the parts due to not being able to locate the part in the breakdown. No water leaks observed during service. ; ordrng 1 PARTSRESEARCH (TOD/thermostat) and 1 WD21X10519 (Float switch)"

Arrived on site to test unit for unit not heating and making loud noise. Found bad high voltage. Replaced magnetron capacitor and diode . Test unit and unit heating and no noise job complete.

"Arrived on site to install previously diagnosed and ordered parts. Per previous techs diagnosis, I removed and replaced the cavity thermostat, fuse and harness. Tested the unit and it is operating as designed. Once I had the unit back in its space, I retested and unit continues to operate as designed. Job completed."

"Arrived on site for no cool in fresh food section. Evaporator incased in ice,removed cover,defrosted evaporator found a blown defrost bimetal,replaced bimetal"

"Arrived on site to inspect refrigerator temps. Upon further inspection, the customer opened the RC door and it was very warm inside. I checked the freezer side and it was the same. I tested the compressor and found it bad. Also found some tubing that was badly corroded and could be the cause of the sealed system issue as it could have developed pin hose due to the corrosion. Customer advised that due to the age of the unit, they will shop around and if they dont find anything, they will contact the office to move forward with repairs.Job completed."

Arrived on site for dryer needing previous diagnosed motor. Upon arrival reconfirmed issue and installed the motor. Was able to reassembled and test unit. Found dryer cycling heating and fully operational. Call complete

"Arrived on site to test unit for cooking light not turning off. Test unit and found stuck relay, replaced control board test unit and found light not coming on relay not closing. Will need to order new control board office to reschedule ; ordrng 1 W11342846 (Control board)"

Arrived on site for refrigerator that had a light go out and has temperature concerns. Inspected unit and work area. Confirmed the customers complaint about the light being out in the Refridgerator section but did not find any issues with temperature. I took temperature in the unit and found the freezer sitting at -1?F in the refrigerator sitting at 37?F. I have the customer get another lightbulb as the one currently inside the unit had broken wiring inside the light bulb. Replaced the light and the unit began to illuminate as designed. The customer said they had bought another one but the replacement bulb did not seem to work. I did inform then that they do sell bad bulbs and that they may have also gotten an LED light which will not work in this unit. The unit is working as designed. Call complete.

Arrived on site for refrigerator not making ice. Upon arrival confirmed complaint and found ice maker stuck in harvest mode. Also found temps in FC and rc were good. Found proper voltage to ice maker but unit would run test cycle. Replaced ice maker and found unit could complete a harvest and fill as designed. Informed customer to give unit 24 hrs to fill bucket. Call complete

Arrived on site for refrigerator creating ice formations in FC floor liner and ice melting together in ice box comp. upon arrival found cause of ice in FC liner was due to gap in FC door gasket under door. Was able to reshape gasket and ensure FC door would correctly seal to prevent air leak again. Found door dispenser flap would not fully seal each time it was activated. ; ordrng 1 WPW10353552 (Ice door)

Arrived on site for washer not allowing cycle selection to run unit. Upon arrival confirmed issue and found stable 120v connection to unit. Also found proper dc voltage to ui encoder. Rotary dial on encoder was failing not allowing a selection cycle. Will need office to reschedule once availability of parts is known. Unit will need knew W11478526 encoder fascia asm. ; ordrng 1 W11478526 (Encoder/fascia asm)

Arrived on site for washer needing previously diagnosed rebuild. Upon arrival installed all needed parts for repairs. Reassembled and tested unit. Found washer fully functioning as designed. With no leaks during repairs or tests. Call complete

Arrived on site for a dryer that had an issue at one point a few weeks ago. Inspected unit and work area. Tested the unit in a high heat cycle and found the dryer heating and tumbling as designed. Used a thermocouple to check the cycling of hat and found it working as designed. Advised the customer that it was in fact working as designed with no issues present.

Arrived on site for dryer not heating. Upon arrival confirmed complaint. Found stable 240v connection. Found all heating hardware except for element were functioning within manufacture specs. Element coil had cracked apart. Replaced coil then reassembled and tested dryer. Found unit cycling heat as designed. Also instructed customer that it would be recommended to get a dryer vent cleaning to ensure prevent of further wear and tear on dryer. Call complete

Arrived on site to install previously diagnosed parts. Inspected unit and work area. Replaced the UI and latch assembly and tested the unit. The unit is working as designed. Call complete.

"Arrived on site to inspect refrigerator temps. Upon further inspection, I tested temps in the FC=6 degrees and RC=38 degrees. I pulled the unit out and tested amp draw to the compressor and it is showing 1.06amps. I inspected the lokring at the back of the unit and they were sealed and dry. I placed the unit in diagnostics and tested and it is operating as designed. I advised the customer that the unit is operating as designed. No water leaks observed during service, job completed."

Arrived back on site to install previously ordered timer. R&R and unit heated as designed. Job complete

Arrived on site to follow up on refrigerator that stopped making ice. Checked icemaker and found icemaker isnt filling. Checked filled tube and found ice stuck in fill tube. Cleared ice and sealed the fill tube with permagum on the back of the cabinet. Retested unit and found valve is no longer humming or filling. Reordering icemaker kit to replace valve again.

"Arrived onsite for washer not cycling correctly. Upon arrival unit was moved out of area and disconnected. Customer was using backup washer in place. Was able to connect and put into diagnostics. Found F7E6 motor fault. Tested agitation and spin modes, all passed. Customer stated the cycle will begin and later will state complete. When the lid is opened the tub is still filled with water. Cycle did not spin and drain. Will order control and motor. Office to reschedule ; ordrng 1 W11399433 (Control) and 1 W11497303 (Motor)"

Arrived onsite and found unit fresh food evap fan is not running and therefore the temp is 45 in fridge. Temp is 0 in freezer. Ordering fan to repair. Office to reschedule. ; ordrng 1 WR60X10179 (Ff fan assembly)

Arrived onsite and tested oven for not heating properly and shutting itself off at 400f. Ran unit for over 20 minutes at 400. Unit operating properly with good cooling fan and at proper temps. Unit is operating as designed at time of service.

"Arrived onsite for bottom spray arm getting stuck and door not closing correctly. Found feed tube assembly was out of place and left side of unit was leg not leveled. Secured the feed tube assembly and leveled the left leg. Tested the unit, the lower spray arm turns freely and the door closes correctly. Job complete"

Arrived on site for dishwasher needing previously diagnosed sump asm. Upon arrival reconfirmed prior issue and installed needed part. After reassembling unit found no leaks during tests and unit fully cycling through all setting as designed. Call complete

"Arrived on site for unit not defrosting. Removed door,drawers and cover,completely defrosted evaporator,replaced harness and cover assembly. Reassembled unit ran diagnostics all test passed.

Arrived on site for dryer not powering up. Checked voltage at block . No power at all on either leg . Did find 120v on green ground at chassis and neutral. Advised to have electrician look at outlet . Job complete

Arrived back on site to install previously ordered actuator. Removed and replaced it and unit finally tested as designed and spun in the drain and spin cycle. Job complete

"Arrived onsite for unit it defrosting as it should, customer said they would let it cool and then it would stop and then they would see a build up of ice. Found that the controls and thermistor need to be replaced. Got authorization, replaced parts. No issues at this time. Job complete. Spoke with PR to help diagnose"

"Arrived onsite for icemaker not working, corrected issue by clearing obstruction on the fill arm. Unit is now operating as designed. Advised customer On repair."

"Arrived on site to insect dishwasher control panel not responding. Upon further inspection, I found all of the selections were responding except for the start button. I removed the outer door panel and outs where some liquid had been spilled on the door and got on the user interface and shorted the start button.No water leaks observed during service, job completed."

"Arrived on site to inspect refrigerator with frost in the freezer section. Upon further inspection, I found the left side of,the FC door gapped approximately 1/8 inch at the gasket. I opened the FC door and found frost built up on the top of FC section, on the drawers, the rails and the door. I closed the FC door and it sealed on all four sides. I tested the door several times by opening and closing the door and holding the door handle in the middle and every time, the door closed and sealed on all four sides. Due to the amount of ice/frost on the slides, I removed and replaced the slides and retested and the door continues to close as designed. I explained the customer that the door must be opened and closed by holding the handle in the middle and demonstrated what happens when the door is not opened from the middle. Customer was not happy with the unit; therefore, I contacted Whirlpool techline and spoke to Travis and advised of the complaint and my findings. Travis advised that the door must be opened from holding the middle of the door handle or it will open at an angle and sometimes will not close properly allowing warm air inside the unit and frost will build up. I advised Travis that I was replacing the slides due to the ice/frost build up on them and causing the grease to harden and make the door difficult to close. Travis provided SR#7732286887. I advised the customer of my conversation with tech support and provided them with the SR# file number and recommended that they contact Whirlpool customer service if they have any further issues with the freezer door. No water leaks observed during service, job completed."

Arrived on site for poor wash performance. Ran diagnostics and pump motor not running . Found wash motor had failed . Replaced sump and motor . Ran diagnostics all checked normal. No water leaks detected at time of service. Job complete .

Arrived onsite for dishwasher not turning on. Upon arrival found wall voltage was good power cord was good giving power to control. Control was not operational. Replaced and proceeded to test. Unit is now operating as designed. Job Completed.

"Arrived on site and for freezer and refrigerator cooling issues. Checked temperatures and confirmed 15 and 50. Immediately spotted massive frost buildup on both sides of the evaporator cover. Advised customer of the findings and ordered defrost thermostat, heater and will return with the thermostat. ; ordrng 1 67004188 (DEFROST HEATER) and 1 67004757 (DEFROST TSTAT)"

Arrived on call for complaint of broken agitator. Confirm that the agitator is broken. Replace agitator.

"Arrived on site and inspected ice machine and found customers complaint was actually related to a different ice machine of a different brand in a different part of the house. This ice machine is unplugged, because homeowner says it was leaking. After reconnecting the power found drain pump is not running. Replaced drain pump and sent a short video of ice machine running and not leaking to MS, job complete"

"Arrived on site to test unit for white residue on clothing. Found error code f0e4(spin limited by water temp). Found cold valve not engaging properly and inlet thermistor out of range. Customer stated unit was moved into current home in May, 2021. Unit is currently connected to soft water system. Replaced valve and recommend using less detergent as softener is creating more suds and will leave residue on clothing. Tested unit, unit working as designed. No leaks detected. Job complete."

"Arrived on site to test unit for not cooling. Found control not responding. Cycled power to unit and control turned on. Put unit in diagnostics and compressor running but no frost pattern developing on evap. Quoted customer for compressor, evap, drier, access valve and control box.will need compressor, evap, dye drier, access valve, control box and nitrogen. 2hr and SS tech on return visit.

Arrived onsite and found center rail snapped. Replaced center rail. Unit is now operating as designed. Advised customer on repair. All checks good.

"Arrived on site and replaced both temperature sensors in both ovens diagnosed on previous visit, after replacement confirmed oven temperature is correct by preheating oven.job complete"

"Arrived on site to diagnose refrigerator with cooling issues, upon arrival the customer informed me that the ice maker is the issue and is not dispensing ice, I gained access to the ice maker and found that the ice maker harvests but doesnt fill, I found the fill tube to be clear of any ice build up. I gained access to the valve and found that the valve needs to be replaced as it is not allowing water to dispense at the ice maker ; ordrng 1 WPW10420083 (Inlet valve)"

"Arrived onsite for oven tripping breaker, upon arrival found unit off and breaker stuck on the middle turned unit back on and found all to be operating as designed proceeded to call techline Sr 7732287904 techline stated to check if unit had 32 or less amps when calling for bake, found it at 30.4 for amps when back is called for. Techline stated if that was the case it was breaker issue. Job Completed."

Arrived on site to diagnose a refrigerator that is leaking from dispenser. Found ice cubes sticking in chute and replaced separator assembly to try to prevent issue. All is working properly at this time and no leaks were found at time of service.

"Arrived on site for refrigerator not producing ice. Inspected unit and work area. Found flex tray broken. Removed ice maker and installed new. Cycled ice maker. All tested good, no water leaks detected during service."

"Arrived on site for refrigerator ice maker leaking water and ice bin broken. Inspected unit and work area. Found ice bucket broken. Forced ice maker gears striped and not cycle properly. Found signs of water leaking from ice maker. Advanced ice harvest cycle and verified water leaking from ice maker. Will need to replace ice maker and ice bucket.Removed failed ice maker and installed new. Cycled ice maker and monitored operation. Found unit working as designed and no leaks from ice maker. Installed ice container. Job completed.

"Arrived on site to test unit for no ice production. Found ice maker stopped mid cycle. Found ice maker power switch was turned off. Turned switch on, tested unit, unit working good. Valve filled ice maker properly. No leaks detected. Job complete."

Arrived onsite for washer locked and not responsive. Upon arrival washer lid was locked and unit was off. Tried putting unit in diagnostics mode but could not. Tested incoming voltage and had none. Checked breaker and breaker was tripped. Flipped breaker and unit powered on. Canceled current cycle and tested. Found no stored error codes. Ran calibration and auto test and both passed. Ran normal load and customer will monitor. Job complete

Arrived on site for range intermittently fault code on display. Inspected unit and work area. Inspected wiring to control. Found all connection good. Performed diagnostics mode and verified failure code of F1-E0. Found internal control fault. Will need to replace control. Found no ETA available on control. Office to schedule appointment when ETA is available.; ordrng 1 W11567348 (Control)

"Arrived on site for sealed system repair. I gained access to the compressor. I replaced the dryer, and access valve.I pulled a vacuum and put 125 psi of nitrogen into the system. I found no leaks. I put a measured charge into the system. I found pressures 2 on low and 125 high. The unit is working as designed. Job complete."

Arrived on site for a washing machine that wont spin . Inspected unit and work area. Confirmed the customers complaint and put the unit in a spin only cycle. Found the motor humming but the basket not moving. Remove the front panel and found the belt detached from the motor. Did not find a belt cracked or broken. I reattached the belt to the motor and the belt had good tension. Tested the unit again and the unit ran as designed. Call complete

"Arrived on site for an oven that will not work and its flashing in the F2 E1 (UI stuck key) error code. Confirmed the customers complaint and flip the breaker for a full minute. Do unit came back on and continue to flash that error code. Replaced the control panel and tested the unit. Unit began to work as designed.Call complete."

"Arrived onsite for a dryer that is still showing the vent needs to be cleaned for better performance even after having his vents cleaned. Inspected unit and work area. Placed the unit in diagnostics and found no stored error codes. Ran the unit through a heavy duty dry cycle and the unit finished without erroring but did fast forward without wet clothes. I called Whirlpool techline and spoke to Austin SR# 7730910924. He advised that based on the fact that the unit did not error without clothes, it would have to be a ventilation issue. He advised that since the customer has a more than 90 degree turn in his attic to go out, it can hinder airflow. He advised that since we have already replaced the control, the unit would not be at fault at this time. He advised to make no repairs. Call complete."

"Arrived on site to test unit for timer not advancing. Verified timer was staying in same position and not advancing on timed dry also found unit will not shut off on sensed dry. Found moisture sensor popped out of place and was making contact other sensor so unit was thinking things were still wet as contacts were closed. Replaced timer and popped moisture sensor back into place, tested unit, unit working as designed. Job complete."

"Arrived on site for a washing machine thats making a grinding and squealing sound. Inspected unit and work area. Placed the unit and serviced diagnostics and tested the spin function. Found the splutch assembly completely grinding on itself immediately and not getting the basket. The customer advised that the unit also is making a squealing noise prior to the grinding sound. Its on the basket by hand and found the unit skipping as if that one of the bearings on the transmission was bad. Check Internet the unit and confirmed that the unit had lost oil underneath. I also found that the belt has been stripped due to the splutch assembly . Replaced the gear case, splutch assembly, and belt and tested the unit. The unit began to work as designed. Call complete."

Arrived on site for glass falling on the vent hood. I found the capacitive glass not sticking to the adhesive. We have the correct 30 glass on order already. The office will reschedule when we have the part.; O-emld tckt

"Arrived on site for no ice and weak water flow. Icemaker not running through a forced cycle,tested water dispenser weak water flow installed bypass good water flow,diagnosed unit will need the updated icemaker kit and filter head assembly. Replaced filter head assembly installed updated icemaker kit,ran water good water flow icemaker filled up with water. ; used 1 W10882923 (Icemaker) from stock"

"Arrived on site for broiler element and baking element not heating. Tested unit and found broiler element is heating, found broken bake element. Bake element needs to be replaced.Office to reschedule"

"Arrived onsite to replace previously diagnosed parts Replaced compressor, dryer and valve. Pulled vacuum and held. Charged per spec and tested. Uncharacteristically unit did not immediately kick on after powering. Went to enter into diagnostics then compressor kicked on. Pressures holding steady. Unit is cooling. Job complete"

Arrived on call for complaint of not cleaning. Ran diagnostics and water level good. Wash motor not working properly. Will need sump and motor that is on order to complete. ; O-emld tckt

Arrived on call for complaint of no power. Checked power supply and found loose connection at box. Reconnect supply and test dishwasher. No leaks detected at time of service.

Arrived on call for complaint of ice on back wall of freezer. Checked the freezer and all is normal. Ran diagnostics and found all good.

"Arrived on site to inspect refrigerator door not closing and shelves not aligned. Upon further inspection, the customer pointed out that the lower drawer in the RC section was not closing properly. Also advised that the crisper pans are not closing properly. I tested the lower pan and found it to not be seating correctly on the rails. I could not determine if the pan is warped or not. I tested the crisper pans and found that when removed, they have to be aligned onto the rails correctly or they will hang on the rails and not close properly. I demonstrated to my customer how to properly install them after removing them to clean. I am ordering the lower pan, pan front, pan handle, left & right side plates, right & left pan slides & left and right side plate slides and office to schedule return service due to the availability of parts. No water leaks observed during service.; ordrng 1 WPW10654844 (Pan) and 1 WPW10510417 (Pan front) and 1 W10398002 (Pan handle) and 1 WPW10498906 (left side plate) and 1 W11225684 (Right side plate) and 1 W10508330 (Pan left slide) and 1 W10508328 (Pan right slide) and 1 W10508327 (Left plate slide) and 1 W10508326 (Plate right slide)"

"Arrived on site to diagnose washer not draining properly, upon arrival I gained access to the unit and put it into diagnostics, I found a fault code pertaining to flood out and over suds, i gained access to service diagnostics and put the unit into a cycle, I found that the unit is operating properly as designed. I informed the customer on use and care and proper cycle use, I informed them of a good detergent and amount to use to avoid over sudsing sending the unit into a flood state. The unit is operating properly as designed, job complete."

"Arrived onsite for unit not getting up to temperature. Looked at the unit , checked sensor and elements. All checked good. Tested unit up too 350 degrees and unit was able to get there with no issues. Tested the bread proof. And unit got up to 103. No issues at this time. Job complete.

Arrived onsite to replace the switches to the unit. Replaced upper switches and and lower switch but the unit managed to blow the breaker.

Arrived on site for unit smoking from oven. Found grease buildup on oven base and baking element. preheated the oven to 350. Unit operates as designed. Instructed customer to clean the build up on the base around the baking element to help with burning smell and smoke. Job complete

Arrived on site and inspected refrigerator and found water reservoir is frozen and dispenser will not run. Added Perma gum filling in air gap between fan scroll Styrofoam and interior liner. Took pictures. Used heat gun to defrost reservoir and it is now running properly. Customers complaint of no filter was actually the filter needing to be reset after being replaced. Job complete

"Arrived on site to diagnose range that had 1 burner that was not working at all. Found you can turn the knob, but burner doesnt come on. Removed panel and checked switch and found a burn mark on the switch for front left burner. Replaced switch and retested. Found unit working as designed and heating.Call complete."

"Arrived on site for dryer making a noise. I inspected the unit and work area. I gained access to the interior of the unit. I inspected the drum rollers we have previously replaced, and the are in good condition and spinning properly. I inspected the motor and the pulley. I found both making a slight squealing noise when rotating. I am recommending the motor, pulley and blower wheel(that attaches to the motor) be replaced.

"Arrived on site to replace previously diagnosed thermistor on no cool refrigerator, I gained access to the fc and steamed out all of the ice and frost build up, upon gaining access to the thermistor I replaced it, the unit is now operating properly as designed

Arrived on site for dishwasher not working. I inspected the unit and work area. I found the wash motor showing open. I put the unit through a diagnostics cycle and found the motor getting 120 vac. I spoke to Christian about replacing the motor. I replaced the wash motor and tested the unit. It is working as designed. Job complete.

"Arrived on site , ran diagnostics. UI non responsive. Unplugged unit . Retried diagnostics, no error codes . Ui slow to respond at times to commands. Replaced UI panel. Ran diagnostics, ui responding to commands properly . All checked normal in test wash . No water leaks detected at time of service. Job complete"

Arrived onsite as helper to SM. Replaced console and tested. Unit is functioning properly

Arrived on site to install previously diagnosed part. Found ice in the current ice mold but motor was not turning all the way to dump and start another harvest. Removed ice maker and installed new ice maker. Tested with harvest and bail arm dropped after calling for water as designed. Asked customer to dump any ice it produces today. Tomorrow morning the ice will be safe to use for drinks. Job completed.

"Arrived on site to diagnose dishwasher not cycling or draining properly, upon arrival I gained access to the unit and put it into service diagnostics, I found a fault code pertaining to the door lock, stuck key and drain pump. I put the unit into a diagnostics cycle and found the sump and motor assembly is operating properly as designed but the drain pump is intermittent, I replaced the drain pump and found that broken glass had seized the drain pump, I tested the unit with the new drain pump and found the unit is operating properly as designed with no leaks observed.job complete."

"Arrived on site to diagnose dryer that is sometimes not fully drying clothes. Ran unit and verified it is heating, but is reading as poor airflow for electric dryer. Advised customer to have vents cleaned as well as some different cycle options. Unit working as designed. Call complete."

Arrived on site for Ice maker Inside ice maker Not holding temp ice is melting. Unit was turned off upon arrival. Checked bin thermistor for resistance and it was in range. Ran diagnostics and all cycles completed without issue and no errors. Plugged drain and ran water valve and allowed bin to fill substantially. Unplugged and motorized pump drained without issue. Asked customer to contact us if it starts failing again and to make sure it remains plugged in and remains plugged in at least 24 hours before we arrive so we can diagnose the issue while its happening. Job completed.

Arrived on site to install a new rc door and UI. I replaced both with new. I reassembled the unit and tested it. It is working as designed. Job complete.

"Arrived on site for dishwasher not cycling or cleaning dishes. Upon arrival confirmed complaint and also found f4e3 in diagnostics. After further tests found sump asm had failed. Replaced sump as, then reassembled and tested unit. Found no signs of leaks or failures and dishwasher now fully functioning properly as designed call complete"

"Arrived on site for fridge making a loud noise. I inspected the unit and work area. I found frost build up on the fc evaporator. I put the unit into diagnostics. I activated the defrost heater and found it coming on. I also found some slight gaps between the cabinet and outer liner. I am ordering the UI, fc thermistor, control and silicone to repair the unit. The office will reschedule when we have eta on the parts. ; ordrng 1 WP482338 (Silicone) and 1 W11558182 (Control)"

"Arrived onsite for vent hood not coming on. Upon arrival inspected wall outlet found proper voltage coming from wall to unit. Found motor receiving voltage but completely dead. Replaced unit. Motor and proceeded to test. Found new unit motor was binding with blower making whining sound coming on barely on high, with rubbing sound. Ordering another motor, office to reschedule upon arrival of parts.; ordrng 1 W11100651 (Blower fan)"

"Arrived on site for dishwasher leaking water. Upon arrival confirmed complaint. Found no errors in diagnostics. After further tests I found water leaking from sump asm, as well as the element bushing. Unit will need new element and sump/motor asm to complete repairs. Call complete ; ordrng 1 W11537778 (Element)"

"Arrived on site to diagnose refrigerator that was not dispensing water or making ice. Ran dispenser and found nothing coming out, but you could hear the valve humming. Removed filter and ran unit and found no issues dispensing water. Replaced filter and ran again. Found unit properly dispensing with new filter. Unit now working as designed. Call complete."

Arrived on call for complaint of not heating. Found the power supply not correct. Customer will have supply corrected.

"Arrived on site to replace sump and motor. Replaced sump and motor. Test unit, unit cycles as designed. No leaks present at this time. Job complete"

Arrived on site to follow up on ice machine that was intermittently not making ice and clumping. Installed new water level sensor and retested unit. Verified proper fill level being reached and not leaking over. Unit working as designed.

Arrived on site for wine cooler not powering on. I found the unit on but not recognizing the door is open. I found the kick plate holding the door switch in. I adjusted the kick plate. The switch now works as designed. Job complete.

Arrived onsite for unit having the lint light always blinking. Looked at the unit and the light would blink when in the on position but will turn off after the unit is started. Was able to confirm that her unit will have the light always blinking as a reminder and will only shut off after starting the unit. No issues at this time. Job complete.

"Arrived on site broiler door falling on left side . Found hinge screws missing . Replaced screws , door is opening and closing properly . No gas leaks detected at time of service. C-note . Job complete"