Service History 1079

Near Cedar Park, TX 78613
James
Job Details: 08/22/2018
Arrived on site and tested unit. Found that unit appeared to,have no power. Removed unit from cabinet and tested fuses. Found both to be good but connection to cavity thermostat loose and secured connection. Plugged unit in to test voltage at control and found proper voltage and unit now powering on. Reinstalled and tested operation. Unit working properly. Job complete.
Near Meadowlakes, TX 78654
Thomas L.
Job Details: 08/22/2018
Arrived on site and replaced in efficient compressor. unit now started properly. All water connections were dr. Customer haven to his work before my work was completed. Locked side door when I left.
Near Georgetown, TX 78633
Jonathan
Job Details: 08/22/2018
Whirlpool refrigerator model# WRS325FDAB02. Ice buildup in freezer compartment.
Near Meadowlakes, TX 78654
Thomas L.
Job Details: 08/22/2018
Arrived on site and replaced in efficient compressor. unit now started properly. All water connections were dr. Customer haven to his work before my work was completed. Locked side door when I left.
Near Austin, TX 78748
Kevin
Job Details: 08/22/2018
Arrived on site and found dryer door will not stay closed, replaced catch and door still pops open. Will need to bring back door strike and if that does not correct the issue tech line will need to be called on that same visit.
Near Kempner, TX 76539
Arthur B.
Job Details: 08/22/2018
WRF535SMBM00 (French Door Refrigerator) - Arrived onsite for customer complaint of icemaker leaking and clumping in ice cube tray. Found ice maker mold cracked. P&L are as follows;W10884390 (Icemaker) $83.67,RF360 $174.99 plus taxes. Removed and replaced icemaker. Icemaker called for water and found mold no longer leaking. All water connections were dry at time of service.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 08/22/2018
Model WTW7500GW0, Arrived on call for washer has lf error when on rinse cycle which lf error is for long fill,checked for error codes and got f3 e2 water inlet temp fault, f8 e1 long fill error, f0 e3 over load, f0 e4 spin limited by water temp, installed water valve and know getting good water flow on hot and cold on machine, instructed customer on loading and soap usage, no water leaks after repair, call complete.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 08/22/2018
Model WTW7500GW0, Arrived on call for washer has lf error when on rinse cycle which lf error is for long fill,checked for error codes and got f3 e2 water inlet temp fault, f8 e1 long fill error, f0 e3 over load, f0 e4 spin limited by water temp, installed water valve and know getting good water flow on hot and cold on machine, instructed customer on loading and soap usage, no water leaks after repair, call complete.
Near Leander, TX 78641
Jerry C.
Job Details: 08/22/2018
WRF535SMBM00 Arrived to inspect no cool in rc. I found the fc evap full of frost and ice. I removed the ice and tested the defrost element and it worked as designed within service test mode. I found the fc door would not close correctly due to upper rack binding. I corrected door lean and the rack binding and tested. I sealed door opening gapping within the fc and rc doors. Operational test good, no leaks observed during service.
Near Cedar Park, TX 78613
James
Job Details: 08/22/2018
Arrived on site and tested unit. Found that magnetron not starting. Removed unit and inspected high voltage system. Found that connection from capacitor to mag loose and that magnetron has failed. Also found that diode has failed indicating issue with capacitor. Installed new magnetron capacitor and diode. Tested for proper operation. Unit working properly. Job complete.
Near Austin, TX 78753
Robert
Job Details: 08/22/2018
MVWB955FC1 Arrived on job to replace hinges, lid, frame and seal. After replacement of all parts lid operation normal. No leaks detected at time of service. Job complete
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 08/22/2018
GSH25JFXBBB (SxS Refrigerator) - Arrived onsite to install new compressor to SxS refrigerator from prior tech’s diagnosis. Removed back cover and tested compressor using start device and capacitor from compressor kit. Fund unit came on and remains running. Checked FC evaporator and found good frost pattern forming and good air flow. Unit does not need compressor replaced. Found start device and capacitor faulty. No other issues found. All water connections were dry at time of service.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 08/22/2018
Model ED5FHEXVS01, Arrived on call for ice maker not making ice and freezer is cooling, found 118 ac volts to ice maker with door switch not pressed, found freezer door switch broken and even with 118 ac volts to maker and t-h jumped ice maker would not cycle, installed ice maker and jumped t-h and ice maker cycled and filled with water, ordering freezer light switch, will reschedule for 8/24/18, no water leaks at time of call
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 08/22/2018
Model ED5FHEXVS01, Arrived on call for ice maker not making ice and freezer is cooling, found 118 ac volts to ice maker with door switch not pressed, found freezer door switch broken and even with 118 ac volts to maker and t-h jumped ice maker would not cycle, installed ice maker and jumped t-h and ice maker cycled and filled with water, ordering freezer light switch, will reschedule for 8/24/18, no water leaks at time of call
Near Liberty Hill, TX 78642
Jonathan
Job Details: 08/22/2018
Whirlpool washer model# WFW92HEFC0. Unit not responding and continues to drain only.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 08/22/2018
Model WOS51EC0AS04, Arrived on call for improper heating for oven, installed ui control and main control and name plate and sensor per previous techs diag. Preheated oven to 350, cut out temp is 395, cut in temp is 324 which is a average temp of 360 degrees, calibrated oven temp down -10 degrees for a average temp of 350 degrees, all checks good, call complete.
Near Pflugerville, TX 78660
Nathaniel B.
Job Details: 08/22/2018
Model WOS51EC0AS04, Arrived on call for improper heating for oven, installed ui control and main control and name plate and sensor per previous techs diag. Preheated oven to 350, cut out temp is 395, cut in temp is 324 which is a average temp of 360 degrees, calibrated oven temp down -10 degrees for a average temp of 350 degrees, all checks good, call complete.
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 08/22/2018
ED5FHEXNT00 (SxS Refrigerator) - Arrived onsite for customer complaint of SxS refrigerator intermittently cooling and shuts off and burning smell. Plugged unit up and found start device shorted out. Compressor would come on and start device sparks. A,so found icemaker not working as well. Icemaker stripper would continuously rotate. Ordering new start device,icemaker, thermostat and defrost control. Advised customer that AHS must approve parts. OF to R/S. Unit unplugged at this time. All water connections were dry at time of service.
Near Georgetown, TX 78628
Jonathan
Job Details: 08/22/2018
Kenmore washer model 417.44132000. Not powering on.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 08/22/2018
Florczykowski
Near New Braunfels, TX 78132
Daniel A.
Job Details: 08/22/2018
KRMF606ESS0 Refrigerator evaporator freezing over. Moved thermistor to correct position on suction line. Verified normal operation after service
Near Killeen, TX 76549
Arthur B.
Job Details: 08/22/2018
RED4516FW0 (Dryer) - Arrived onsite for customer complaint of dryer making noise when tumbling. Removed door front and found rock lodged in drum seal. Removed rock and reassembled. Tested unit. Unit now tumbles quietly. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Austin, TX 78736
Kevin
Job Details: 08/22/2018
Arrived on site and replaced control board diagnosed by previous technician. Found ice production is currently good. Added silicon around freezer liner to remove any air gaps between eight and outer cabinet. No water leaks from connections at time of service, job complete.
Near Austin, TX 78703
Robert
Job Details: 08/22/2018
LA612 washer no spin.
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details: 08/22/2018
Removed and replaced weak inlet water valve. Fill cycle is now working properly. Tested unit and unit now works properly with no water leaks.
Near Liberty Hill, TX 78642
Jonathan
Job Details: 08/22/2018
Whirlpool washer model # WTW5000DW1. Washer not powering on.
Near Killeen, TX 76549
Arthur B.
Job Details: 08/22/2018
NTW4605EW0 (Top Load a Washer) - Arrived onsite for customer complaint of top load washer stuck in “WASH” cycle. When arrived, found unit was drained and emptied. Ran diagnostics and found no error codes. Calibrated unit. Unit calibrated successfully. Tested unit. Unit fills,agitates,drain and spins with no issues. All water connections were dry at time of service.
Near Austin, TX 78733
Luis
Job Details: 08/22/2018
Refrigerator-replaced failed water filter housing
Near Georgetown, TX 78628
Tyler B.
Job Details: 08/22/2018
Near Kingsland, TX 78639
Thomas L.
Job Details: 08/22/2018
Arrived on site for no operation. Unit was totally inoperable. Reset breaker and retested. Unit no came on but with no display operation. Unit then shut off again. Unit needs a control rebuild. Est$600. Due to age of unit customer is looking into new units.
Near Leander, TX 78641
Cliff
Job Details: 08/22/2018
Ikea microwave IBMS1455DS00. Arrived on site to diagnose a microwave that will not start. Found start button has come unmounted from button clip. Remounted button and tested unit. Found all is functioning properly at this time.
Near Liberty Hill, TX 78642
Jonathan
Job Details: 08/22/2018
Whirlpool refrigerator model# WRF736SDAM13. Intermittently cooling issue in fresh food compartment.
Near Georgetown, TX 78628
Tyler B.
Job Details: 08/22/2018
Near Kingsland, TX 78639
Thomas L.
Job Details: 08/22/2018
Arrived on site for no cool in freezer. Freezer temp was 36 and fresh food was 46 degrees. Found loose connection at condenser fan motor causing fan not to run thus high temps. Corrected. Customer to allow approx 24 hours for u it to reach normal temps. No water is hooked up to unit.
Near Killeen, TX 76542
Arthur B.
Job Details: 08/22/2018
DU1100XTPSA (Dishwasher) - Arrived onsite for customer complaint of soap dispenser cover broken on dishwasher. Confirmed door flap tab is broken. Removed and replaced dispenser. Reassembled. Door now opens/closes as intended. No other issues found. All water connections were dry at time of service.
Near Dripping Springs, TX 78620
Brandon
Job Details: 08/22/2018
Arrived on site for part hanger, I replaced bi metal and control board, unit tested good.
Near Georgetown, TX 78628
Tyler B.
Job Details: 08/22/2018
Near Liberty Hill, TX 78642
Jonathan
Job Details: 08/22/2018
Whirlpool refrigerator model# WRX735SDHZ00. Leaking water at top of unit.
Near Leander, TX 78641
Cliff
Job Details: 08/22/2018
Jennair compactor TC707S4. Arrived on site to diagnose a compactor that is starting when the door is closed and foot release is not correctly aligned. Tested unit and found trashbin not latch to front panel and start button not engaging switch. Realign start button and attached trash bin properly. Tested unit found all is functioning properly at this time.
Near Kingsland, TX 78639
Thomas L.
Job Details: 08/22/2018
Arrived on site for thin ice production. All operations tested correct in diagnostics. However thickness was set on medium thickness setting. Change setting to thick. All water connections were dry.
Near Killeen, TX 76542
Arthur B.
Job Details: 08/22/2018
WED8000DW4 (Dryer) - Arrived onsite for customer complaint of UI lettering on dryer had came off after removing packing film. Confirmed the letter peeled off. Removed UI assembly and installed new replacement. Removed film. All lettering intact. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Killeen, TX 76548
Arthur B.
Job Details: 08/22/2018
GS5SHAXNL00 (SxS Refrigerator) - Arrived onsite for customer complaint of SxS refrigerator making loud grinding noise when running. Found evaporator fan is barely moving. Will need new evaporator fan to complete repair. Next available for customer is Monday 8/27. All water connections were dry at time of service.
Near Georgetown, TX 78628
Jonathan
Job Details: 08/21/2018
Whirlpool refrigerator model# WSF26C3EXW01. Has oder inside of unit and in ice.
Near Austin, TX 78728
Cliff
Job Details: 08/21/2018
Whirlpool refrigerator WRT1L1TZYW00. Arrived on site to install heater kit for refrigerator. Tested unit and found drain was clogged and heater kit was not needed. Unclog the drain and removed all ice from the freezer. Tested unit and found all is functioning properly at this time. No leaks found at time of service.
Near Georgetown, TX 78628
Jonathan
Job Details: 08/21/2018
Whirlpool refrigerator model #WRS571CIHZ01. Making intermittently noises.
Near Austin, TX 78724
Scott
Job Details: 08/21/2018
Lid lock op load washer
Near Austin, TX 78744
Robert
Job Details: 08/21/2018
WRS321SDHZ01 Arrived on job for complaints of too cold. Found the diffuser door open and frost in refrigerator. Replaced diffuser and door closed. No leaks detected at time of service. Job complete
Near Killeen, TX 76542
Arthur B.
Job Details: 08/21/2018
WRX735SDBM02 (French Door Refrigerator) - Arrived onsite for customer complaint of icemaker not making ice on French door refrigerator. Removed ice bin and found ice maker stripper keeps rotating. Removed faulty icemaker and installed new replacement. Reassembled. Icemaker called for water immediately. No other issues found. All water connections were dry at time of service.
Near Leander, TX 78641
Thomas L.
Job Details: 08/21/2018
Arrived on site for issues with inside oven floor. Found oven floor pan was not installed properly. Corrected. Unit is good to,go. Open builder home. Left him a voice mail stating oven is fixed.
Near Killeen, TX 76549
Arthur B.
Job Details: 08/21/2018
GFSS6KKYESS (French Door Dual Evaporator Refrigerator) - Arrived onsite for customer complaint of not French door refrigerator not cooling in RC section. Found evaporator fan is not moving air in section. Ordering evaporator cover assembly to complete repair. R/S set for Friday 8/24. Customer will have unit defrosted before return visit date. All water connections were dry at time of service.
Near Leander, TX 78641
Thomas L.
Job Details: 08/21/2018
Arrived on site for frosting in the freezer section. Upon inspection of the frost is actually at the air vent that goes into the icemaker compartment. As I inspected the unit I found that the unit was turning off and on continuously. I also found that the user interface on the inside of the left door is no longer operable. I am ordering both controllers.
Near Cedar Park, TX 78613
Lou
Job Details: 08/21/2018
arrived on site to inspect dryer not working. Upon further inspection, I found the unit unplugged and the cord on the unit was the wrong cord. The cord itself was to a GE dryer. I advised the customer that they needed a Whirlpool approved four prong cord that has the round prong on top, the two straight prongs on the sides and the upside down "L" shaped prong on the bottom. I verified ohms to the components fuse, cutoffs, element. No lint observed during service, job completed.
Near Round Rock, TX 78665
Tyler B.
Job Details: 08/21/2018
Near Austin, TX 78728
Wesley
Job Details: 08/21/2018
WRT518SZFM00 Arrived on site for freezer seal set incorrectly. Used heat gun to re shape. All checks good. Unit is now operating as designed.
Near Temple, TX 76501
James
Job Details: 08/21/2018
Arrived on site and tested unit. Found that unit has fault for lid lock and would not start a cycle. Installed new lid lock and tested operation. Found that gearcase is making a grinding sound. Inspected gearcase and found that it is starting to leak oil. Also found that actuator not reading basket speed. Unit will also need new gear case cam and actuator to complete repair. Will need autho to complete repair. All water connections dry at time of service.
Near Cedar Park, TX 78613
Lou
Job Details: 08/21/2018
arrived on site to inspect dryer not turning on. Upon further inspection, I verified voltage at the outlet, but wasn't getting the correct voltage at the terminal block. I found that the wires were not installed correctly. The red was on black and black on red. I corrected the issue and the unit operates as designed. No lint observed during service, job completed.
Near Killeen, TX 76549
Arthur B.
Job Details: 08/21/2018
HDA3400G00WW (Dishwasher) - Arrived onsite for customer complaint of dishwasher not starting cycle. Removed Baotou toe plate to check incoming voltage. Found 120V to unit. Removed console and found bracket that touches door switch is warn. Was able to adjust bracket to allow,door latch to make contact. Unit now comes on and off as intended. Unit fills,agitates,drain heats as intended. No other issues found. All water connections were dry at time of service.
Near Austin, TX 78748
Kevin
Job Details: 08/21/2018
Arrived on site and set refrigerator into diagnostic cycle and found on Test 56 error E2 motor lost position. Attempted test 57 and icemaker would not cycle. Replaced ice maker Ran test 57 again and it completed properly. Also ran test 45 and valve fill ice maker. Recommended to customer that first batch of ice be discarded. No water leaks from connections at time of service, job complete
Near Lago Vista, TX 78645
Thomas L.
Job Details: 08/21/2018
Arrived on site for Noisey operation. Found idler pulley very Noisey. Installed new dryer repair kit. Cleaned dryer during repairs.
Near Round Rock, TX 78665
Tyler B.
Job Details: 08/21/2018
Near Leander, TX 78641
Lou
Job Details: 08/21/2018
arrived on site to inspect dishwasher leaking water. Upon arrival, the customer advised that the unit is leaking water randomly. He advised that they will sometimes wake up in the morning and find water at the front of the unit and underneath, as well. Upon further inspection, I placed the unit in diagnostics and error codes 6/4 and 8/2 appeared. I cleared the error codes and continued with testing. While testing, I checked underneath the unit for any leaks and found none. Before testing was completed, I checked under the sink counter and found that the customer has a RO system and the line was tapped into the dishwasher drain line going into the disposal. At that point, I recommended that the customer contact a plumber to come and relocate the RO system line somewhere other than at the disposal closer to the pee trap. The unit completed testing and there were no error codes showing. There was a lot of detergent suds in the bottom of the unit, so I recommended that the customer cut bac
Near Jarrell, TX 76537
James
Job Details: 08/21/2018
Arrived on site and tested unit. Found that stirrer and stirrer cover damaged. Also found wave guide cover loose. Unit will need new stirrer assembly and wave guide cover to repair.
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 08/21/2018
HVM1750SP2SS (OTR Microwave) - Arrived onsite for OTR microwave not coming on. Uninstalled microwave and removed control panel. Found fuse blown. Removed fuse. Tested unit. Found work coming from control board. Ordering control board to complete repair. R/S for a Friday 8/24. Customer agreed to keep unit uninstalled until unit is repaired.
Near Leander, TX 78641
Lou
Job Details: 08/21/2018
arrived on site to inspect dryer not drying clothes. Upon arrival, the customer was explaining that it takes several attempts at drying before the clothes actually get dry. She opened the unit to get some clothing out of the unit and I found that the customer is putting too many clothing articles inside the unit. Upon further inspection, I used my dryer vent tester and tested the airflow in the unit and it tested good as the card fell off the hanger two out of two times. I verified ohms to the cutoff, fuse, and element. I pulled the element to inspect the coils and found that one of the connections was broken in two but was touching enough to operate. I removed and replaced the element and tested the unit and it was operating as designed and heating properly. I recommend them the customer only dry small loads to help in drying times. No lint observed during service, job completed.
Near Florence, TX 76527
James
Job Details: 08/21/2018
Arrived on site and tested unit found full of water. Tested pump and pump is making a humming sound and not draining. Removed water and inspected pump found motor has failed and is just humming. Unit will need new drain pump to repair quoted customer $67.58 plus tax for pump and $159.99 plus tax labor(TL210). Installed new pump and tested operation. All functions test good and all water connections dry at time of service. Job complete
Near Austin, TX 78723
Scott
Job Details: 08/21/2018
Fridge whirlpool Keeps tripping the breaker
Near Austin, TX 78735
Kevin
Job Details: 08/21/2018
Arrived on site and found saved error codes for Water level system error, and no water detected entering machine. Ran a diagnostic cycle and found All functions are operating properly confirmed that pressure hose and air trap are clear. If situation happens again will need to bring back air trap, pressure hose and pressure sensor. No water leaks from connections at time of service, job complete.
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 08/21/2018
Near Bastrop, TX 78602
Nathaniel B.
Job Details: 08/21/2018
Near Austin, TX 78726
Wesley
Job Details: 08/21/2018
WDT920SADM0 Arrived on site and replaced sump and motor. Tested unit, all checks good. Unit is operating as designed. Leak free. Charged balance.
Near Leander, TX 78641
Lou
Job Details: 08/21/2018
arrived on site to install previously diagnosed and ordered parts. I arrived with the front panel, door parts and a strike. I removed and replaced the inner and outer door assembly and the strike and tested the door. The door closed and latched as designed. I did not need to replace the front panel as the door was warped which was keeping it from staying closed. No lint observed during service, job completed.
Near Austin, TX 78739
Leonardo
Job Details: 08/21/2018
KitchenAid range oven not coming on model: KSGG700ESS1. Arrived on site to test unit for not igniting. Test unit and found regulator not releasing gas. Replaced regulator test unit and unit test good job complete no leaks present at this time. Oven heating to 350
Near Cedar Park, TX 78613
Thomas L.
Job Details: 08/21/2018
Arrived on site for no operation and F5 E1 failure code. Entered diagnostics to clear failure code and performed self diagnostics test mode. After doing so the oven performed with failure code returning.
Near Georgetown, TX 78633
James
Job Details: 08/21/2018
Arrived on site and tested unit. Found that main control has failed and unit will not start. Quoted customer $349.99 plus tax for control and 209.99 plus tax labor(BI150) to repair. Customer would also like both fresh food door baskets replaced. Quoted customer $150.91 plus tax per gasket(needs 2). And additional $200.00 plus tax labor(BI280). Installed new control kit and tested operation. Unit will still need gaskets to complete repair. Collected for control and labor of control. Customer to pay for gaskets and gasket install labor on return visit. All water connections dry at time of service
Near Leander, TX 78641
Lou
Job Details: 08/21/2018
arrived on site to install previously diagnosed and ordered part. Removed and replaced the diffuser and tested the unit. Unit operated as designed. I had the customer listen to the diffuser open and close and she was good with the operation. No water leaks observed during service, job completed.
Near Austin, TX 78704
Robert
Job Details: 08/21/2018
ED5LHAXWQ00 Arrived on job for complaints of filter stuck. Got filter out of housing. Customer purchased filter. Quote $51.49. No leaks detected at time of service. Job complete
Near Liberty Hill, TX 78642
Jonathan
Job Details: 08/21/2018
GE refrigerator model# GFD28GBLCTS. Not dispensing water.
Near Killeen, TX 76549
Arthur B.
Job Details: 08/21/2018
WRS973CIDM00 (SxS Dual Evaporator Refrigerator) - Arrived onsite for customer complaint of SxS Dual Evaporator Refrigerator condensing on walls of RC section. Tested unit in step 4 and found condenser fan motor not running causing warm air to enter mullion. Ordering new condenser fan to complete repair. R/S for Friday 8/24. All water connections were dry at time of service.
Near Round Rock, TX 78681
Wesley
Job Details: 08/21/2018
WRF767SDHZ arrived on site and found unit fill tube not positioned inside the fill cup. Inserted properly. Now unit produces as designed. All checks good.
Near Leander, TX 78641
Thomas L.
Job Details: 08/21/2018
Arrived on site for unit not finishing cycle. Found unit has a failed latch assembly. Latch $51.47 Work $179.99 Sub $234.46 plus tax
Near Austin, TX 78703
Robert
Job Details: 08/21/2018
110.75132410 Arrived on job for complaints of noise. Pulled vent tube and found stick had fallen into tube and was rubbing on fan. No gas leaks detected. Job complete quote customer $159.99 labor.
Near Harker Heights, TX 76548
Arthur B.
Job Details: 08/21/2018
WMH73521CS6 (OTR Microwave) - Arrived onsite for customer complaint of OTR microwave squeaking when fan is running. Removed trim vent and found flap is squeaking when opening and closing. Used silicone lubricant to flap. Squeaking disappeared. No other issues found.
Near Round Rock, TX 78665
Tyler B.
Job Details: 08/21/2018
Near Austin, TX 78748
Leonardo
Job Details: 08/21/2018
Whirlpool dishwasher no power model: WDF520PADM7. Arrived on site to test unit for no power. Test unit and found wire nut to white wire at junction melted. Replaced wire nut test unit and unit test good no error codes no leaks present at this time job complete.
Near Georgetown, TX 78633
James
Job Details: 08/21/2018
Arrived on site and installed control and bulb. Tested for proper operation. Unit now working properly. Job complete.
Near Nolanville, TX 76559
Arthur B.
Job Details: 08/21/2018
MFI2568AES (French Door Refrigerator) - Arrived onsite to install new hinge assembly to French door refrigerator from tech’s prior diagnosis. Removed RH door and installed new hinge and closer. Reassembled. Door now closes smoothly. No other issues found. All water connections were dry at time of service.
Near Georgetown, TX 78626
Jonathan
Job Details: 08/21/2018
Whirlpool oven model# WFG515S0ES0. Not heating.
Near Buda, TX 78610
Leonardo
Job Details: 08/21/2018
Whirlpool microwave inner light not coming on model: WMH53520CB5. Arrived on site to test unit for inner light not coming on right away. Test unit and found bad 3way switch. Replaced 3 way switch test unit and unit test good inner light coming on right away job complete.
Near Buda, TX 78610
Robert
Job Details: 08/21/2018
WRF993FIFM00 Arrived on job to replace bottom icemaker. After replacement test all good . No leaks detected at time of service. Job complete
Near Georgetown, TX 78628
James
Job Details: 08/21/2018
Arrived on site and tested unit. Found that left rc door liner collapsing and not making contact with door switch. Will need new left door to repair. Instructed customer that door orders take 6-8 weeks to arrive. All water connections dry at time of service.
Near Kyle, TX 78640
Brandon
Job Details: 08/21/2018
Arrived on site for customer complaint of washer not powering on. I found power was getting to main control board, but I did not have proper dc voltage going to UI from main board. I quoted customer for main control board and informed her I could not further diagnose without a functioning UIB. She is going to call Maytag to see if they will pay for the repair.
Near Kyle, TX 78640
Kevin
Job Details: 08/21/2018
Arrived on site and found no ice production, cycled icemaker and motor has failed. Replaced ice maker and it cycled properly and filled, no water leaks from connections at time of service, job complete.
Near Killeen, TX 76549
Arthur B.
Job Details: 08/20/2018
FEF316ASA (Range) - Arrived onsite for tenant complaint of bake element not working. Found bake element shorted near rear of element. Unit will need new element. R/S for Friday 8/42 is her next available. No other issues found.
Near Austin, TX 78726
Cliff
Job Details: 08/20/2018
Whirlpool cooktop SC8720EDB3. Arrived on site to diagnose a cooktop that has two rear burners not igniting. Found burners clogged, due to normal wear and tear, causing no gas to reach igniters. Cleared clog from burners and tested unit. Found all is functioning properly at this time. No gas leaks were found at time of service.
Near Lampasas, TX 76550
Arthur B.
Job Details: 08/20/2018
WOD93EC0AS05 (Wall Oven) - Arrived onsite for customer complaint of wall oven lower oven door shattered. Confirmed lower oven door damage. Inner glass in tact. P&L are as follows; W10577911 (Outer Glass Assembly) $$218.29,SHIPPING $75.00,WO220 $169.99. Total $501.50 with tax. Removed shattered out glass assembly and installed new replacement with existing handle. Reinstalled door to oven. Customer satisfied with new replacement. No other issues found.
Near Austin, TX 78739
Luis
Job Details: 08/20/2018
Refrigerator-replaced start device
Near Austin, TX 78729
Cliff
Job Details: 08/20/2018
Whirlpool washer WFW72HEDW0. Arrived on site to diagnose a washing machine is making abnormal noises when draining. Tested unit found normal debris and washed up catching pump impeller. The debris has damaged impeller. Replaced pump and tested unit. Found all is functioning properly at this time. No leaks were found at the time of service.
Near Hutto, TX 78634
Tyler B.
Job Details: 08/20/2018
Near Leander, TX 78641
Jonathan
Job Details: 08/20/2018
Whirlpool dishwasher model# WDF520PADM5. Not cleaning dishes.
Near Austin, TX 78745
Kevin
Job Details: 08/20/2018
Arrived on site and replaced thermistor recommended by tech line on previous visit, requested that customer monitor refrigerator for correct operation. No water leaks from connections at time of service, job complete