Service History 1074

Near Florence, TX 76527
Jonathan
Job Details: 09/11/2018
Hotpoint refrigerator model # HSS25GFPJWW. Intermittently cooling.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 09/11/2018
Model GDF540HGD2BB, Arrived on call for dishwasher will not turn on after closing door, found that power switch on counter was turned off, turned it back on and know dishwasher is powering on, also found that gasket is coming out of channel of outer tub to allow door to seal, will order gasket, will reschedule for 9/14/18 at customers request, no water leaks at time of call.
Near Hutto, TX 78634
Nathaniel B.
Job Details: 09/11/2018
Model GDF540HGD2BB, Arrived on call for dishwasher will not turn on after closing door, found that power switch on counter was turned off, turned it back on and know dishwasher is powering on, also found that gasket is coming out of channel of outer tub to allow door to seal, will order gasket, will reschedule for 9/14/18 at customers request, no water leaks at time of call.
Near Georgetown, TX 78628
Cliff
Job Details: 09/11/2018
Whirlpool refrigerator WRX735SDHZ00. Arrived on site to replace freezer door for refrigerator. Replaced door and sealed cavity with clear food grade silicone. Tested unit and found all is functioning properly at this time. No leaks were found at time of service.
Near Killeen, TX 76541
Arthur B.
Job Details: 09/11/2018
MQF1656TEW02 (Upright Freezer) - Arrived onsite for customer complaint of ice build up in freezer floor. Removed evaporator cover and found drain tube clogged. Used steamer and found water flow well to drain pan. No other issues found. No water connections to unit at time of service.
Near Kyle, TX 78640
Derek S.
Job Details: 09/11/2018
MBF2258DEM00 Arrived on site to repair unit for not cooIing found the compressor is only running for three seconds indicating a faulty start device and capacitor ordering parts to complete the repair no water leak present at the time of service
Near Kyle, TX 78640
Derek S.
Job Details: 09/11/2018
MBF2258DEM00 Arrived on site to repair unit for not cooIing found the compressor is only running for three seconds indicating a faulty start device and capacitor ordering parts to complete the repair no water leak present at the time of service
Near Georgetown, TX 78633
Thomas L.
Job Details: 09/11/2018
Arrived on site or issues with the lower rack operation. Found that the lower rack wheel assemblies were failing. Replaced all four lower rack assembly. Lower rack and upper rack are both not working properly. Water connections were all drive.
Near Georgetown, TX 78633
Tyler B.
Job Details: 09/10/2018
Near Burnet, TX 78611
Thomas L.
Job Details: 09/10/2018
Arrived on site for no cool condition. Found all operations running and freezer temp was a 6 and fresh food was at 40. All water connections were dry.
Near Leander, TX 78641
James
Job Details: 09/10/2018
Arrived on site and tested unit. Found that drain pump is seized and not draining water. Installed new drain pump and tested operation. Unit working properly and all water connections dry at time of service. Job complete.
Near Austin, TX 78703
Robert
Job Details: 09/10/2018
KRFF707ESS01 Arrived on job for complaints of noise and warm temperature. Customer thawed unit already so I removed cover to inspect and found the thermistor in wrong position. Moved thermistor to rear top as Whirlpool wants. Job complete
Near Cedar Park, TX 78613
Lou
Job Details: 09/10/2018
arrived on site to inspect dryer making loud noise. Upon further inspection, I turned the unit on and could hear a loud screeching noise. I removed the front panel and then removed the drum and using my jumper wire, I jumped the door switch and turned the unit on to get a better idea of where the noise was coming from. It sounded as if the noise was coming from the motor so I turned it by hand and could hear the screeching noise. I removed the back of the unit and the air vent to expose the motor wheel and found a bra wire logged in the wheel. I removed the wheel and tested the unit and the noise was gone. Due to the rollers being dirty and making some squeaking noises while testing, I removed and replaced the dryer kit and put t(e unit back together and tested ad the unit operated as designed and very quiet. No lint observed during service, job completed.
Near Austin, TX 78748
Derek S.
Job Details: 09/10/2018
MFI2665XEW6 arrived on site to repair unit for no ice production, I confirmed no ice and found ice maker module not responding electrical failure, replaced the ice maker assembly kit and verified operations, no water leak present at the time of service
Near Austin, TX 78748
Derek S.
Job Details: 09/10/2018
MFI2665XEW6 arrived on site to repair unit for no ice production, I confirmed no ice and found ice maker module not responding electrical failure, replaced the ice maker assembly kit and verified operations, no water leak present at the time of service
Near Meadowlakes, TX 78654
Thomas L.
Job Details: 09/10/2018
Arrived on site for no operation. Tested unit and found open thermostat. Replaced And tested. Unit now works properly. Dryer and house venting are both clean.
Near Austin, TX 78737
Kevin
Job Details: 09/10/2018
Arrived on site and inspected washer and found error code for Long drain, found drain pump catch is blocked by debris and there is no water flowing through it. After clearing drain pump ran a diagnostic cycle and it is now operating properly. No water leaks from connections at time of service, job complete.
Near Georgetown, TX 78633
Tyler B.
Job Details: 09/10/2018
Near Marble Falls, TX 78654
Thomas L.
Job Details: 09/10/2018
Arrived on site for unit not starting. Found start button on control panel failed. Replaced control panel and tested. Operations are all now normal and dry.
Near Austin, TX 78748
Derek S.
Job Details: 09/10/2018
WRS571CIDM02 Arrived on site to repair unit for freezing items in the fresh food section, i did confirm the items were freezing, the fridge temp was set to 35 degrees, I informed Mr Baydu that the recommendation per factory is 37 and may need to raise higher to avoid freezing, temps can go to 45 degrees, unit is working as designed, no water leak present at the time of service
Near Austin, TX 78748
Derek S.
Job Details: 09/10/2018
WRS571CIDM02 Arrived on site to repair unit for freezing items in the fresh food section, i did confirm the items were freezing, the fridge temp was set to 35 degrees, I informed Mr Baydu that the recommendation per factory is 37 and may need to raise higher to avoid freezing, temps can go to 45 degrees, unit is working as designed, no water leak present at the time of service
Near Austin, TX 78736
Kevin
Job Details: 09/10/2018
Arrived on site and found heating element is operating properly, found several upper rack plastic pieces are missing or broken. Will need to order all pieces, no water leaks from connections at time of service, job complete.
Near Austin, TX 78721
Robert
Job Details: 09/10/2018
KRFC300ESS01 Arrived on job to replace door. After replacement of parts test gasket. Operation normal. No leaks detected. Job complete
Near Kingsland, TX 78639
Thomas L.
Job Details: 09/10/2018
Arrived on site for no spin condition. Entered vacation home via garage door and code per builder. Found unit would not spin. Calibrated the control via step 4 of diagnostics. Unit now operates mproperly with no water leaks.
Near Round Rock, TX 78681
Tyler B.
Job Details: 09/10/2018
Near Round Rock, TX 78681
Tyler B.
Job Details: 09/10/2018
Near Austin, TX 78733
Kevin
Job Details: 09/10/2018
Arrived on site and found ice production is good, took 1 picture. Found temperature in freezer is 4-5 degrees. Temperature in fresh food is 40-42 over temp alarm is beeping but after clearing it has stopped. Alarm was likely due to doors being opened for a while when last diagnosis happened. No water leaks from connections at gime of service, job complete.
Near Austin, TX 78748
Derek S.
Job Details: 09/10/2018
WDT710PAHZ1 Arrived on site to check unit for not drying the dishes, I ran service test and all functions checked good, heated is working and unit is working as designed, informed Mrs to use rinse aid to assist with drying and how to adjust, also gave tips for optimal performance, no water leak present at the time of service
Near Austin, TX 78748
Derek S.
Job Details: 09/10/2018
WDT710PAHZ1 Arrived on site to check unit for not drying the dishes, I ran service test and all functions checked good, heated is working and unit is working as designed, informed Mrs to use rinse aid to assist with drying and how to adjust, also gave tips for optimal performance, no water leak present at the time of service
Near Kingsland, TX 78639
Thomas L.
Job Details: 09/10/2018
Arrived on site for no spin condition. Entered vacation home via garage door and code per builder. Found unit would not spin. Calibrated the control via step 4 of diagnostics. Unit now operates mproperly with no water leaks.
Near Cedar Park, TX 78613
James
Job Details: 09/10/2018
Arrived on site and tested unit. Founder lower latch on door has broken off. Removed broken piece of latch from interlock and installed new door. Tested for proper operation and found unit working properly. Job complete
Near Cedar Park, TX 78613
James
Job Details: 09/10/2018
Near Morgan's Point Resort, TX 76513
Arthur B.
Job Details: 09/10/2018
MTB2254MES00 (Top Mount Refrigerator) - Arrived onsite for tenant complaint of top mount refrigerator not cooling in fresh food compartment. Found evaporator not running. Removed evaporator cover and remove faulty fan motor. Installed new replacement. Cleared air channel of any ice. Reassembled. Tested unit. Unit now circulating air as intended. No other issues found. No water source connected to unit at time of service.
Near Georgetown, TX 78626
Dona
Job Details: 09/10/2018
Arrived on site for no operation on unit, found after previous tech replaced door locks unit then no longer had door error. Once door lock error went away unit would then not power on. Replaced main control that was burned on 3421 and 3419 connectors. Once control replaced unit would run for approximately 4-7 seconds and then shut off. Found low voltage on transformer not allowing supply to run control. Also found that customer stated there was major noise before unit stopped working. Will need to bring capacitor diode and magnetron with transformer on next visit to verify unit is heating. Will need authorization ordering one CNOTE- authorization. Unit is unplugged. Office will reschedule once authorization is received.
Near Kingsland, TX 78639
Thomas L.
Job Details: 09/10/2018
Arrived on site for no ice condition. Found freezer temp at -1 and fresh food at 38 degrees. Found emitter / receiver giving double flash failure code.
Near Austin, TX 78729
Wesley
Job Details: 09/10/2018
WFG320M0BS3 Arrived on site to diagnose gas smell. Found unit to be operating leak free. No smell detected during testing. Advised customer on findings and demonstrated diagnostic process. All checks good.
Near Kyle, TX 78640
Derek S.
Job Details: 09/10/2018
WMH1163XVQ0 Arrived on site to repair unit for not heating, found magnetron shorted and caused damage to capacitor and diode, replaced the magnetron, capacitor and diode and verified operations with no issues.
Near Kyle, TX 78640
Derek S.
Job Details: 09/10/2018
WMH1163XVQ0 Arrived on site to repair unit for not heating, found magnetron shorted and caused damage to capacitor and diode, replaced the magnetron, capacitor and diode and verified operations with no issues.
Near Lakeway, TX 78734
Luis
Job Details: 09/10/2018
Ice machine-replaced failed water sensor
Near Little River-Academy, TX 76554
Arthur B.
Job Details: 09/10/2018
WFW92HEFW0 (Front Load Washer) - Arrived onsite to remove and replace tub assembly from my prior visit’s diagnosis. Removed cracked tub and installed new replacement with valve and drain pump. Reassembled. Tested unit. Unit now fills,agitates,drain and heats as intended. Water supply is leaking. Turned supply off. Customer was aware of the leak. No other issues found. No water leaks detected at time of service.
Near Austin, TX 78741
Kevin
Job Details: 09/10/2018
Arrived on site and replaced motor pulley, and repair kit, and handle diagnosed on previous visit. After replacement dryer is working properly, job complete arrived on site and replaced motor pulley, and repair kit, and handle diagnosed on previous visit. After replacement dryer is working properly, job complete
Near Burnet, TX 78611
Thomas L.
Job Details: 09/10/2018
Arrived on site for no operation. Found unit totally dead. Found L1 wire loose in junction box. Corrected and tested unit. Unit now operates properly with no water leaks.
Near Georgetown, TX 78633
Lou
Job Details: 09/08/2018
arrived on site to inspect washer start button not working. Upon further inspection, I placed the unit in diagnostics and checked for error codes. Error codes 9/2, 0/5 appeared. As I attempted to clear the codes, the unit UI would not function correctly and would not clear the codes nor allow me to advance into diagnostics mode 51. I removed and replaced the main control and control panel and placed the unit in diagnostics and calibrated the unit under mode 52. After calibration, I placed the unit in mode 51 and continued with testing. The unit operated as designed with no error codes at the end of testing. No after leaks observed during service, job completed.
Near Georgetown, TX 78633
Lou
Job Details: 09/08/2018
arrived on site to inspect oven temps. Upon arrival, the customer advised that they were baking and the food came out not fully cooked and were concerned that the unit wasn’t heating properly. Using my thermal couple, I placed my lead in the middle of the center rack and turned the unit on at Bake 350 degrees. At the 350 degree notice, I had a reading of 353. I continued with my readings and achieved 328, 366,323, and 374 for an average of 349 degrees. I advised the customer of my findings and there there is no reason to calibrate the unit. No gas leaks detected during service, job completed.
Near Kempner, TX 76539
Arthur B.
Job Details: 09/08/2018
GSS20IEMBWW (SxS Refrigerator) - Arrived onsite for customer complaint of SxS refrigerator making noises. Slid unit out and found noises is coming from evaporator fan in freezer area. Advised that compressor is good and unit is cooling properly. AHS will not replace part due to noise. Unit is working as intended. All water connections were dry at time of service.
Near Harker Heights, TX 76548
Arthur B.
Job Details: 09/08/2018
ED5PVEXWS06 (SxS Refrigerator) - Arrived onsite for SxS refrigerator not cooling properly and shutting on and off. Found defrost filter indicator flashing and not resetting. Removed defrost timer and thermostat. Reassembled. Unit now comes on and cools properly. Unit filter light is now green. No other issues found. Collected 1 Guard SVC fee of $60.00. All water connections were dry at time of service.
Near Belton, TX 76513
Arthur B.
Job Details: 09/08/2018
WED75HEFW0 (Dryer) - Arrived onsite for customer complaint of dryer not heating. Removed dryer bulkhead and found element grounded on base and cutoff with no continuity. Removed and replaced cutoff and element. Reassembled. Tested unit. Unit now heats and tumbles as intended. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Belton, TX 76513
Arthur B.
Job Details: 09/08/2018
MVWC565FW0 (Top Load a Washer) - Arrived onsite for customer complaint of washer not completing cycles and fill issues. Ran diagnostics and found error code F8E3 (Overflow Condition). Found drain hose was too long and sitting on floor. Was able to shorten drain hose and install properly to drain port of house. Calibrated unit. Unit completed successfully. Tested unit. Unit fills,agitates,drain and spins as intended. No other issues found. All water connections were dry at time of service.
Near Temple, TX 76504
Arthur B.
Job Details: 09/08/2018
WTW5000DW1 (Top Load Washer) - Arrived onsite for customer compliant of top load washer not completing cycles. Ran diagnostics and found error code F2E1 (Stuck Key), F8E1 (Long Fill). Cleared error codes and ran calibration. Unit calibrated successfully. Tested water valves. Water valve check ok. Did notice customer has seal off drain. Advised to add an air hole to allow proper air ventilation. No other issues found. All water connections were dry at time of service.
Near Temple, TX 76501
Arthur B.
Job Details: 09/08/2018
MVWC555DW1 (Top Load Washer) - Arrived onsite for customer complaint of top load washer not completing cycles. Tested unit and found lid latch not locking and keeps clicking. Found lid latch faulty. Removed lid latch and installed new replacement. Reassembled. Calibrated unit. Unit calibrated successfully. Unit now locks,fills,agitates,drain and spins with no issues. Charged labor TL330 $59.99 plus taxes. All water connections were dry at time of service.
Near Austin, TX 78741
Chase
Job Details: 09/07/2018
WED5000DW2 Arrived on site to repair unit for not heating, found thermal cut off reading open, found air vent restriction, removed the lint out of unit and duct, replaced thermal cutoff, verified all operations with no isssues, notified Mrs to have the apt air duct professionally cleaned, if the same issue occurs it would not be covered under warranty, dryer and duct free of lint at the time of service.
Near Georgetown, TX 78628
Lou
Job Details: 09/07/2018
arrived on site to inspect oven door glass broken. Upon further inspection, I found that t(e upper oven door inner glass had shattered and needed replacing. Using my vacuum, I cleaned up the remaining glass pieces from the door and installed the new inner door glass. Placed the door back on the unit and cleaned the glass from around the unit and the bottom oven door. Job completed.
Near Killeen, TX 76549
Arthur B.
Job Details: 09/07/2018
WFW8740DC0 (Front Load Washer) - Arrived onsite for customer wanting to clean out drain trap on front load washer. Charged labor FL190 $149.99. Gave customer 10% military discount. Removed front door assembly and removed drain trap. Found coins inside drain trap. Reassembled. Cleared error codes. Tested unit. Unit now washes,agitates,drain and spins as intended. All water connections were dry at time of service.
Near Austin, TX 78741
Chase
Job Details: 09/07/2018
GTW810SPJ1MC Arrived on site repair unit for water leakage, found that a hose was not properly connected to the water valve and causing leak, reinstalled the hose and added a hose clamp to secure hose onto the valve, verified operations unit is no longer leaking.
Near Killeen, TX 76549
Arthur B.
Job Details: 09/07/2018
WED49STBW1 (Dryer) - Arrived onsite for customer complaint of dryer not heating properly. Removed back panel and checked element. Found element has no continuity. Removed and replaced element. Reassembled and tested. Dryer now heats and tumbles as intended. No other issues found. Dryer vent and lint trap as clean of lint at time of service.
Near Liberty Hill, TX 78642
Thomas L.
Job Details: 09/07/2018
Arrived on site for no operation. Found open fuse in control panel. Replaced fuse and unit tested correctly.
Near Liberty Hill, TX 78642
Thomas L.
Job Details: 09/07/2018
Arrived on site for unit that will not dispense water. At this time the water dispenser work properly. Unit will need a right fresh food section door gasket. Will check dispenser again on return visit.
Near Pflugerville, TX 78660
Tyler B.
Job Details: 09/07/2018
Near Buda, TX 78610
Chase
Job Details: 09/07/2018
Near Pflugerville, TX 78660
Tyler B.
Job Details: 09/07/2018
Near Kyle, TX 78640
Chase
Job Details: 09/07/2018
WRX735SDBM03 Arrived on site to repair unit for no ice production. Ice production had stopped for several days. Cycled ice maker and found all functioned but motor has stalled. Replaced ice maker. It cycled and filled. All checks good. Job complete. No water leaks present.
Near Kempner, TX 76539
Arthur B.
Job Details: 09/07/2018
MEDB855DC4 (Dryer) - Arrived onsite for complaint of dryer not heating. Checked incoming voltage and got 240V. Removed drum and check cutoff and element. Found cutoff with no continuity but element checked ok. Removed and replaced cutoff. Reassembled and tested. Dryer now heats as intended. No other issues found. Dryer vent and lint trap was clean of lint at time of service.
Near Cedar Park, TX 78613
Lou
Job Details: 09/07/2018
arrived on site to inspect oven door gasket loose and door glass scratched. Upon further inspection, I found that the door gasket is hardening and falling off and needs to be replaced. Also, the inner door glass is badly scratched. I removed the door and removed and replaced the inner door glass and door gasket and put the door back in place. Job completed.
Near Burnet, TX 78611
Thomas L.
Job Details: 09/07/2018
Arrived on site for Noisey operations. Customer loaded clothes in unit so we could get a good weight in the unit. All operations were normal and no leaks were found. U
Near Pflugerville, TX 78660
Tyler B.
Job Details: 09/07/2018
Near Kyle, TX 78640
Chase
Job Details: 09/07/2018
WRF535SMBM00 Arrived on site to repair unit for no ice production and freezer light not coming on, found that the freezer door switches was iced up and causing the switch to malfunction, found that the ice maker module was defective fill circuit was shorted, replaced the ice maker and verified operations, cleaned out the switch and verified operations and that the freezer door is sealing properly. No water leak present at the time of service
Near Buda, TX 78610
Chase
Job Details: 09/07/2018
WRF757SDEM00 Arrived on site to repair unit for no ice production, ran service diagnosis test for ice maker and found error code motor lost position, also the ice maker failed the harvest test cycle, will need to have ice maker replaced due to mechanical failure, replaced the ice maker and verified unit and ice maker operations with no issues. No water lea
Near Buda, TX 78610
Chase
Job Details: 09/07/2018
Near Kingsland, TX 78639
Thomas L.
Job Details: 09/07/2018
Arrived on site for thin ice condition. Added water manually to the reservoir above the level that the machine itself put in and the unit made thick ice. Contacted manufacturer and he suggested to put the unit in manual fill and make sure that the voltage stays constant to the water valve which it did not. Thus indicating a defective control. This is a vacation home there for customer needs the 19th for service. Andrew SR# 7722894913
Near Kempner, TX 76539
Arthur B.
Job Details: 09/07/2018
TFX28PBDABB (SxS Refrigerator) - Arrived onsite to install new water tubing to SxS refrigerator from prior rediagnosis. Removed dry rotted water line and installed new 5/16th tubing. Connected water supply and turned on. Tested water dispenser and found water now dispenses with no water leaks. No other issues found. All water connections were dry at time of service.
Near Leander, TX 78641
Lou
Job Details: 09/07/2018
arrived on site to inspect noisy dryer. Upon further inspection, I turned the unit on and immediately it began to make a loud rubbing noise. I removed the top and front lower panel to inspect and when I turned the unit on again, I could hear that the noise was coming from the rear rollers area. I removed the door and drum and as I was replacing the rear rollers, I found that the right rear roller was rubbing on the axle causing the friction noise. I removed and replaced the dryer kit and tested. Unit operated as designed with no noise. No lint observed during service, job completed.
Near Georgetown, TX 78626
Tyler B.
Job Details: 09/07/2018
Near Horseshoe Bay, TX 78657
Thomas L.
Job Details: 09/07/2018
Arrived on site for unit leaking water. When I arrived the unit was pulled out of the cabinet approximately halfway. The Mr. requested that I not to do the repair because they were busy. He did inform me that the plumber pulled the unit out the wall to turn the water off and they found that the copper tubing behind the fridge was leaking. I informed the Mr. that that would be house related not product related. The Mr. will have his plumber replace the leaking copper pipe.
Near Georgetown, TX 78626
Tyler B.
Job Details: 09/07/2018
Near Georgetown, TX 78626
Tyler B.
Job Details: 09/07/2018
Near New Braunfels, TX 78130
Kevin
Job Details: 09/07/2018
Arrived on site and Set oven to preheat and found vent and fan are operating properly. Vents location is normal and explain to customer that high temperatures or Long cook times may result in hot air blowing from vent. This is normal operation and can’t be adjusted. Job complete.
Near Round Rock, TX 78665
Jonathan
Job Details: 09/07/2018
Whirlpool washer model# WTW5000DW1. Not spinning and clothes are coming out wet.
Near Austin, TX 78746
Luis
Job Details: 09/07/2018
Built in Subzero-replaced fresh food evaporator
Near Killeen, TX 76542
Arthur B.
Job Details: 09/07/2018
GSS25JFPAWW (SxS Refrigerator) - Arrived onsite to install parts to SxS refrigerator from prior tech’s diagnosis. Removed evaporator cover and defrosted evaporator. Upon defrosting evaporator, found defrost heater element is shorted out. Will need element heater assembly to complete repair. R/S for 9/11. Unit now cooling but will er to complete repair. All water connections were dry at time of service.
Near Austin, TX 78702
Robert
Job Details: 09/07/2018
JVM3162RJ1SS Arrived on job for complaints of noise. Found the heat shield too close to transformer. Moved shield and test . Noise now normal.
Near Cedar Park, TX 78613
James
Job Details: 09/07/2018
Arrived on site and tested unit. Found very little water flow from dispenser and ice cubes are very small. Checked water line and found it to be pinched behind unit. Corrected supply line and tested. Unit working properly and all water connections dry at time of service. Job complete
Near Marble Falls, TX 78654
Thomas L.
Job Details: 09/07/2018
Arrived on site for both oven not heating and multiple burners not igniting. Both oven igniter’s are defective. The left front burner is defective. However all of the burner head screws are corroded and will break into burner heads. All must be removed to do the repair. So that means two igniters will need to be replaced. All five burners need to be replaced. All burn or screws will need to be replaced. This is an approximate $900 repair and the customer wants to look at new units. $90.92 each. Oven igniters $62.22 each burners $289.99 work
Near Belton, TX 76513
Arthur B.
Job Details: 09/07/2018
WRX735SDBM00 (French Door Refrigerator) - Arrived onsite for customer complaint of french door refrigerator not making ice. Removed ice maker assembly and found ice maker stripper motor shorted. Removed ice maker and installed new replacement. Reassembled. Ice maker called for water immediately. No other issues found. All water connections were dry at time of service.
Near Austin, TX 78747
Luis
Job Details: 09/06/2018
Refrigerator-replaced failed ice box fan
Near Liberty Hill, TX 78642
Thomas L.
Job Details: 09/06/2018
Arrived on site or unit leaking water. The Filmin that takes the water into the icemaker has a hole in it it is spraying water out. Water is turned off.
Near Leander, TX 78641
Lou
Job Details: 09/06/2018
arrived on site to inspect refrigerator not dispensing ice and water in the bottom of the freezer. Upon further inspection, I found that the Evap drain tube was clogged and causing the water buildup in the bottom of the freezer. I unclogged the tube and it flowed freely. Also, I found that the ice chute door was broken. I removed and replaced the ice chute door and tested and it operated as designed. No water leaks observed during service, job completed.
Near Liberty Hill, TX 78642
Thomas L.
Job Details: 09/06/2018
Arrived on site for improper operation. Upper oven Would program but not run. Replaced controls and tested unit. Unit now operates correctly.
Near Austin, TX 78758
Wesley
Job Details: 09/06/2018
KDTE254ESS2 Arrived on site and found wires shorted at power block. Corrected wiring. Unit operating as designed. All checks good. No leaks at time of service.
Near Round Rock, TX 78665
Tyler B.
Job Details: 09/06/2018
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 09/06/2018
WRX735SDBM00 (French Door Refrigerator) - Arrived onsite for customer complaint of icemaker not making ice on french door refrigerator. Found icemaker stuck mid harvest. Removed icemaker and installed new updated replacement. Reassembled. Icemaker called for water immediately. No other issues found. All water connections were dry at time of service.
Near Marble Falls, TX 78654
Thomas L.
Job Details: 09/06/2018
Arrived on site for him proper temperatures. I found that the freezer 10° in the fresh food was at 46°. Upon inspecting unit I found a beautiful frost pattern on the evaporator coil. I found that the condenser coil needed vacuuming very badly. I also found that the fresh food air vent hood products in front of it totally blocking it. I suspect these two things were causing the M proper temperature conditions as both fans and the compressor were working properly. All water connections were dry.
Near Copperas Cove, TX 76522
Arthur B.
Job Details: 09/06/2018
MFI2570FEZ05 (French Door Refrigerator) - Arrived onsite for customer complaint of center mullion damaged causing warm air to enter. Found bottom part of mullion hinge damaged. Removed damaged hinge and installed new replacement. Reassembled. Tested unit. Door opens and closes as intended. No other issues found. All water connections were dry at time of service.
Near Austin, TX 78747
Chase
Job Details: 09/06/2018
MHW5500FC0 Arrived on site to repair unit for e1f9 error long drain, found unit was draining water slow, removed the pump filter and found pump clogged with debris, cleared out all the debris from pump and verified unit is draining as designed, all functions Checked good in service test, no water leak present at the time of service.
Near Killeen, TX 76541
Arthur B.
Job Details: 09/06/2018
CAE2745FQ0 (Top Load Washer) - Arrived onsite to install new balance ring and tub ring to top load washed from my prior visit’s diagnosis. Removed top and removed damaged parts. Installed new replacements. Reassembled and calibrate unit. Unit calibrated successfully. No other issues found. OF to charge labor TL230 $189.99 plus taxes. All water connections were dry at time of service.
Near Del Valle, TX 78617
Scott
Job Details: 09/06/2018
Washer whirlpool not draining
Near Georgetown, TX 78633
Jonathan
Job Details: 09/06/2018
KitchenAid dishwasher model# KUDE60FVSS0. Not heating.
Near Austin, TX 78738
Luis
Job Details: 09/06/2018
Built in Kitchenaid-replaced failed icemaker
Near Marble Falls, TX 78654
Thomas L.
Job Details: 09/06/2018
Arrived on site for icemaker spilling in freezer. Found slow turning module causing unit to overfill and leak. Replaced ice maker and all water connections are dry.
Near Killeen, TX 76549
Arthur B.
Job Details: 09/06/2018
KRMF706ESS01 (5 Door French Door Dual Evaporator Refrigerator) - Arrived onsite for customer complaint of 5 door french door refrigerator not cooling intermittently and water not dispensing. Removed back control cover and found control relay clicks on and off. Removed HV control and installed new replacement. Reassembled. Unit came on and began cooling immediately. Water dispenser not works as intended. No other issues found. All water connections were dry at time of service.
Near Kyle, TX 78640
Chase
Job Details: 09/06/2018
WRX735SDHZ00 Arrived on site to repair unit for not dispensing cubed or crushed ice, replaced the motor, washer, and impeller, checked over the ice bucket as well, verified not crushed and cubed operations with no issues, no water leak present at the time of service.