"Arrived on site for customer complaint of of freezer temperature down button not working and frost in freezer compartment. Found UI button not making good contact with push button, I adjusted control within housing, unit tested good. Found freezer door gasket compression not even, I adjusted the tracks/rails, unit tested good."

"Arrived on site to diagnose refrigerator that is not cooling. Checked temps and found FC and RC at room temp. Checked at compressor and found compressor is not running, and cold to the touch. Verified proper AC and DC voltage at inverter, but no power going to compressor. Ordering inverter to resolve. ; ordrng 1 WR55X20817 (Inverter)"

"Arrived on site . Replaced tub seal and hinge pads . Ran diagnostics, no water leaks detected at time of service. Job complete"

Arrived onsite for cooktop that is rusting. Upon inspection I confirmed the multiple rust spots around the edges of the cooktop and op the top near the burners. The cooktop was fairly clean and I did not see any evidence of spills. The customer would like to reach out to the manufacturer to see if they will provide any assistance on the repair. No gas leaks detected during time of service. Office to R/S due to part availability. ; ordrng 1 W11204397 (Cooktop)

"Arrived onsite for disposal breakdown. Unit is now operating as designed. No leaks detected during service. Job Completed"

"Arrived onsite for previously diagnosed parts. Upon arrival replaced door, gasket and leveled unit. Unit is now operating as designed. Job Completed."

"Arrived on site for no cool. Found all leds off,compressor and fans not running,no response deli ui,removed deli ui no damage to harness or control. Removed drawer found broken wire in harness sleeve,unplugged deli control power cycled unit all leds and compressor powered on diagnosed unit will need harness

"Arrived on site for dryer having long dry times. Inspected unit and work area. Disassembled unit to inspected belt driven blower wheel. Found all attached and working. Tested fuses and element. Found element failed, will need to replace element and clean unit with shop vac.Removed failed element and installed new. Cleaned lint buildup from unit. Assembled unit and tested operation. All tested good.

Arrived onsite to install water tank. The customer agreed so I replaced the tank and tested the unit. The unit is working as designed at this time and no leaks were detected during time of service. Job complete.

Arrived on site to test unit for sparking. Test unit and found cap and diode burned out. Replaced both parts test unit and unit test good job complete.

"Arrived on site to diagnose dishwasher that was not starting and running drain pump constantly. On arrival turned on unit and found it running pump and beeping. Found a blinking F8E4 code for float switch. Removed toe kick and found float switch was unplugged. Plugged in switch and retested unit. Found unit filling, pumping and draining properly. No water leaks found. Call complete."

"Arrived onsite for refrigerator with interior lights out. Upon inspection I confirmed the complaint. I replaced the FC LED module and tested the unit. The lights restored but the customer brought to my attention the water is not dispensing. I found the water barely trickling out when engaged I removed the filter and still had the same results. I also found the damper is loud and grinding indicating a failure in the damper control. I will order both valves, filter housing and the damper control for return visit. Office to R/S due to part availability. ; ordrng 1 W10865826 (Inlet valve) and 1 WPW10341329 (Dual valve) and 1 W11194438 (Housing) and 1 WPW10479155 (Damper)"

"Arrived on site to inspect range cooktop burner not working. Upon further inspection, the customer advised that the unit sparked at the back left area of the control panel. I removed the back panel, and found that the back left burner switch had arced/shorted out. I removed and replaced the switch and tested and it is operating as designed. When I tested the other burners, I found the front left burner would not come on. I found where the switch had arced as well (photo). I inspected the right side switches and found they both had arced and the back burner only operated on high. I am ordering the left front burner switch and both right switches and office to schedule return service. ; ordrng 1 WPW10434452 (Left front switch) and 1 WP3149400 (Orange switch) and 1 WP3149404 (Right rear switch)"

Arrived onsite and found clogged cold water valve causing unit to not operate properly. Replaced valve. All checks good. . Replaced valve. Unit is now operating as designed without leaking at time of service.

"Arrived onsite to install previously diagnosed parts. I installed the emitter and receiver boards. The indicator led now has a constant blink and the ice ,asker filled while onsite.

"Arrived on site for dishwasher leaking . Found leak was from sump and motor diverter. Replaced sump and motor. Ran diagnostics, all checked normal. No water leaks detected at time of service."

"Arrived on site to follow up on dishwasher not running. Found the console mostly unresponsive, and also found broken upper rack adjustor.

"Arrived on site and inspected washer and found F6E2 showing on display for communication failure. Control board and control panel would need to be replaced in order to correct issue. Harness between the two should also be prescreened.

"Arrived on site to install previously diagnosed parts. Removed lid and 90 hinges. Opened top cover and removed both left and right hinges. Installed new left and right hinges. Installed new lid and 90 hinges. Powered up unit and placed in diagnostics. Tested lid lock and it is working as designed. Hinges allow door to open and close easily. No rubbing or uneven surfaces when lid is closed. Brought customers into laundry room to have them inspect and see the lid lock latch, unlatch, open, and close without issue. Job completed."

"Arrived on site for a dishwasher that wont fill or run and will flash random lights on the UI. They also stated it did not drain. I put the unit into diagnostics mode and found stored error codes F9E2 for drain motor electrical problem, F8E4 for float switch open, and F10E2 for vent wax motor electrical problem. I cleared the error codes. I then gained access to the bottom of the unit and found the float switch assembly with water in it. I ran a test cycle and found it aggressively leaking from the sump and motor right above the float switch assembly. I manually drained the unit the drain pump worked as designed. This indicates the wax motor and control issue that has been throwing off the drain pump. We will need to order the sump and motor with the drain pump attached, vent wax motor, and return with the control already on order to complete the repair. Office to reschedule. I recommended the customer not use the unit until repaired. ; ordrng 1 W11416460 (Vent Assembly) and 1 W11184028 (Vent Gasket) and 1 W11460946 (Sump and Motor)"

Arrived on job for complaints of not washing properly. Found actuator not in correct position. Replaced actuator and ran test cycle. No leaks detected at time of service

"Arrived on site for Noisy when drying clothes....perhaps a worn drive belt? Found noise coming from inside unit. Found motor was making a winding noise. Connected jumper to lid switch with door, drum, and belt removed. Could hear the noise coming from motor. Had customer confirm the noise. Noise was not as loud because the drum and belt werent attached adding pressure to the motor to make noise louder. Tested rear wheels and they were spinning as designed. Removed motor and blower wheel was seized onto motor threaded stem. Used drill to remove blower and extracted motor. Once new motor was placed I could not get the brackets to seat.Explained situation to customer. . ; ordrng 1 279827 (Motor)"

"Arrived on site for range small oven not igniting. Inspected unit and work area. Gained access to igniter and tested operation. Found sparking igniter not sparking but could hear clicking from control. Gained access to spark module and traced wire harness to igniter and found grounded before igniter. Corrected harness and tested operation. Tested cooktop burners and found flame to high. Found valve were not adjusted after propane conversion, correct burner flame. All tested good."

Arrived on job for complaints of lights out . Confirmed the error and called tech line. Tech line had me check voltage all good and said to replace module.

"Arrived on site for customer complaint of of no ice, found emitter controls did not have any lights, I replaced emitter control boards, unit tested good."

"Arrived on site for a defective filter head,removed built in from enclosure,replaced defective filter head assembly,checked water connections no leaks,installed bypass tested after good flow to icemaker and filled icemaker"

"Arrived on site for customer complaint of no ice, found broken ice maker forks preventing ice maker from rotating, I replaced ice maker, unit tested good."

Arrived onsite for wall oven turning on by its self and the control panel doing weird things. Due to a recent service pointer on this issue I am reaching out to techline to document and get advise on which route to follow for the repair. SR#7731198955 techline recommended cycling power to the unit and if the issues persist then we would need to revisit once a software update is released for this issue. Job complete.

"Arrived on site for cooktop burners not igniting. Inspected unit and work area. Verified failure. Found most screws on burners rusted and to remove most orifice holder, screws and possible burners heads would need to be replaced to replace igniters. Cleaned igniters and made minor adjustment. Tested burners and found lighting.

Arrived on job to replace previously diagnosed parts. After replacement test operation. No leaks detected at time of service.

Arrived on site to test unit for no power. Test unit and found unit giving midwired unit. Advised customer to get unit out and checked the connection. Job complete.

"Arrived on site to diagnose refrigerator that was not cooling. On arrival customer advised me that another company had come out and attempted to fill with Freon, and unit still has not cooled. Diagnosed unit. Found another company had installed a quick access tap on the access line. Checked pressures and found 0 psi equalized pressure. Ran unit with compressor on and found no change in pressures. Compressor sounds incredibly weak and is heating up. ; ordrng 1 W10841139 (Compressor) and 1 W10528578 (Process Tube) and 1 876765 (Tube Kit) and 1 W10890886 (Pan heater) and 1 WPW10205102 (Evaporator) and 1 W1050992 (Heat Exchanger) and 1 212643 (Permagum)"

Arrived on site to install previously diagnosed parts. Inspected unit and work area. Replaced actuator and tested unit. Unit was still having the same problem.

Arrived on site for washing machine making a grinding noise. Upon arrival customer instructed us that it was happening during the spin cycle. Gained access to the motor assembly and found white dust all over the cam and rubbed teeth indicating that the cam and pulley were grinding together. Disassembled cam and installed new cam and belt. Reassembled unit and ran it through a full diagnostics cycle to find everything functioning as intended. Call complete.

"Arrived on site to diagnose downdraft that is no longer moving up and down and stuck in the up position. Opened unit and found the motor arm broken off and laying in the bottom of the unit.

"Arrived on site. Found auger motor not rotating diagnosed a defective auger motor,replaced motor tested motor u it working as designed."

"Arrived on site to diagnose dishwasher that customer reported was not able to get streaks and stains out of. On arrival customer had showed me that the unit seems to be streaking and doesnt maintain the same brightness as when delivered. I cleaned the unit with affresh stainless steel cleaned and was able to remove streaks and stains.unit working as designed. Call complete."

Arrived on job for complaints of door not closing and front not attached. Will need catch for door issue and clip for front issue. ; ordrng 1 279570 (catch door dryer) and 1 W10854425 (clip)

"Arrived on site and replaced drain hose diagnosed on previous visit, ran a diagnostic cycle to ensure washer is no longer leaking, job complete"

"Arrived onsite for washer not completing cycle. Upon arrival put unit in diagnostics. Diagnostics failed on first try. Unplugged unit and tried again. Found error codes for off balance load and lid latch failure. Ran auto test and noticed a small noise in the spin cycle. Tried running individual agitation and spin and did not do either. Ran test again and did not complete spin. Checked for errors again got shifter failure and basket speed fault. Replaced actuator but did not fix issues. Tried spin again and did not complete. Feels like gearcase is slipping. Tried removing washplate but could not remove. Unit seems to have multiple issues. Need to order wash plate, lid latch, motor and belt. Bringing back gearcase, control and cam. Off balance load. Lid lock fault. Will need AUTHO for multiple parts and major repair. Office to reschedule.; ordrng 1 NEEDSAUTHO (NEEDS AUTHO ) and 1 W10752283 (washplate) and 1 W11283592 (motor-drve) and 1 W11307244 (latch) and 1 WPW10006384 (drive belt)"

"Arrived on site for not dispensing ice. Found dispenser door solenoid not engaging dispenser door bracket,removed solenoid removed obstruction in solenoid,reassembled unit tested ice dispenser unit working as designed."

"Arrived on site to inspect range burner issues. Upon further inspection, the tenant advised that the cooktop elements only operate on high settings. I inspected the receptacles and elements and all look good. I pulled the unit out and removed the back panel and found all four burner switches had shorted out. I advised the tenant of my findings. all four (4) burner switches will be needed. I advised the tenant that the unit cooktop is not safe to use until all switches can be replaced. Unit oven is operational. Job completed."

"Arrived on site for water left in the washing machine. We inspected the unit and work area. We found no fault codes in diagnostics and found the unit working as designed at the end of a diagnostics cycle.

"Arrived on site for a dishwasher with lights flashing on the UI and the UI not responding. Upon further inspection I found the start, drying, and delay LEDs all flashing. This indicates either a control or UI failure. I turned power off to the unit and closed the door. The unit did nothing. This built in test on the unit indicates a failed control. I replaced the control and the flashing stopped. The UI was still not responding though. I checked voltage at the block and control. I found both had 120VAC. I checked and found the correct 15VDC going to the console as well. This indicates a failed console too. Will need to return with the console on order to install for repair. Office to reschedule. ; ordrng 1 CNOTE (Needs Autho) and 1 CNOTE (Need To Bring Back Console On Order Already)"

"Arrived on site and replaced lid latch, washer will now run normally, job complete"

Arrived onsite and tested unit for lighting issues. Made some adjustments and instructed maintenance supervisor on findings. Unit had not been plugged in properly for testing prior to arrival. Plugged in and tested. All checks good. Unit is now operating as designed.

Arrived on site for washer not working. Upon arrival found f0e1 error indicating there was a load of clothes in the washer during a Clean Washer cycle. Instructed the customer to run the Clean Washer cycle with nothing in it to completion before resuming normal use. Call complete.

Arrived on site to test unit for fan not working. Test unit and found blower getting power but not Turin on. Replaced blower test unit and unit test good job complete.

Arrived onsite for unit making a noise. Tested the unit and heard a bit of a screeching noise. Looked under the unit and found that the belt was loose and the cam needed to be replaced as it was worn down. Replaced both cam and (Belt from truck stock w11239857). Tested unit. Unit tested good. No leaks at this time. Job complete

Arrived on site to replace inner door glass due to glass shattering during self clean. Found provided door glass was damaged in transit. Reordering door glass. ordrng 1 W10829001 (Door glass Inner)

"Arrived on site and inspected DR error code on a Maytag Bravos washer. Confirmed the complaint and accessed the drain pump and found it to be defective. Removed and replaced it, reassembled and unit tested as designed.

"Arrived on site to inspect range oven temps. Upon further inspection, using my multimeter, I placed my thermal lead in the middle of the center rack and tested temps on Bake at 350 degrees. My five test readings were 388, 311, 381, 309, 382 for an average of 354.2 degrees. Unit is operating as designed. Per manufacturer readings, temps should be within 10 degrees below & 10 degrees above the testing temp. In this case, 350 degrees was the testing temp and average temp is showing to be within range of the testing temp. Oven temps can only be tested by using a multimeter with thermal lead and not a thermometer as stated on page 7 of the owners manual due to the fluctuation in temps. Tested the cooktop burners and all are operating as designed. No gas leaks detected during service, job completed."

Arrived onsite for refrigerator not cooling. Upon inspection I found the FC=8 RC=38 and the ice bin full of ice. Normal sized cubes. The customer stated that they had a brown out for a few hours and the unit since restored function and has been keeping cool and making ice for a week. I tested the RC and FC evap thermistors and both showed within range. Due to the brown out restoring the function I went ahead and replaced the HV control board and asked the customer to continue monitoring the unit to ensure it keeps good temps. No leaks detected during time of service. Job complete.

"Arrived on site and inspected dishwasher not starting. rdering part needed to get the unit back in operating condition. NEEDS MORE WORK ; ordrng 1 W10655806 (HARNS-WIRE) and 1 WPW10348269 (DRAIN PUMP) and 1 W10327250 (REG, WATER INLET) and 1 W10739633 (PUMP & MOTOR) and 1 WPW10545278 (DRAIN HOSE) and 1 W10817282 (CONTROL MODULE)"

Arrived on site for a dryer coming on but not turning. Upon arrival the customer stated the unit is also heating. I gained access to the tub and found the belt intact. I then checked voltage at the wall and found it good. I gained access to the terminal block and found both neutral and ground wires on ground. The unit had not been installed correctly. I adjusted the wires and then tested the unit. The unit is now working as designed. I also found the vent hose on the back completely pinched shut. I advised the customer to replace this as well. Otherwise they will see a lack of performance and possible further damage to the unit. I let them know lack of airflow can also be a fire hazard.

"Arrived on site and inspected washer and found actuator arm is out of cam kit ring. Per service pointer replaced actuator, and also replaced capacitor. ran a diagnostic cycle and confirmed Washer is now operating normally. No water leaks from connections at time of service, took pictures, job complete"

Arrived onsite for cooktop with dented console. Upon arrival I confirmed the complaint. I was going to install the new console but I found a scratch on the front of the new console left side.; ordrng 2 W11444496 (Console)s

"Arrived on site to install previously diagnosed and ordered part. Due to the defrost thermistor shorting out, I removed and replaced the thermostat and tested. Unit is cooling as designed. I recommended that the customer allow the unit to cool for 24 hours before putting their food items back into the freezer section. No water leaks observed during service, job completed."

Arrived onsite for previously diagnosed parts. Upon arrival replaced unit control and UI and unit is now operating as designed. Job Completed.

"Arrived onsite to replace both refrigerator door seals to the unit. Replaced both seals. Checked to see if the gasket was not sealing correctly, gaskets are sealing with no issues. Let customer know that the seal will take a while longer to form better to the cabinet and not to be alarmed by the small ripples near the edges. No issues at this time. Job complete"

"Arrived on site for damaged door. Replaced freezer door and installed nameplate,removed ice build up remolded freezer door gasket. Door sealing correctly to cabinet. ; used 1 W10839793 (Nameplate) from stock"

"Arrived on site to inspect refrigerator ice maker not working. Upon further inspection, I checked the ice bin and found a few cubes in it. Using my jumper wire, I jumped the ice maker motor from points T-H and it failed. I cycled power to the unit and retested and it continued to fail. Using my jumper wire, I attend to get the IM to call for water at points L-V and it failed. I removed the ice maker and found the harness connector to the ice maker has a tab that secures it to the side the motor housing and the tab was broken causing the connection to get loose. Using a harness from my van stock (W10884720 ), I removed and replaced the harness and retested and the ice maker is operating as designed. No water leaks observed during service, job completed."

"Arrived on site to inspect refrigerator no cool. Upon further inspection, I tested temps in the FC=40 degrees & RC=51 degrees. I removed the upper cover and found the compressor extremely hot. Tested amp,draw to the compressor and got 2.95amps. No water connections to the unit; no water leaks observed during service, job completed."

Arrived on site for a washing machine that has all lid lock issue. Inspected unit and work area. Placed unit and service diagnostics and found an F1 E2 (motor over voltage) and F9 E1 (long drain) error codes. Tested the lid lock and found the Luna attempting to Lott. Replace main control due to several issues and tested the unit in a manual lid lock again and found the lid attempting to lock but not registering the lid being closed. Replaced large assembly and tested unit again. The unit began locking and unlocking as designed. Ran the unit through an auto test in the unit ran as designed. Call complete.

"Are on site for refrigerator not cooling. Upon arrival found following temps in both compartments fluctuating (FC: 12?to 18?, Rc: 53? to 55?) exposed both evap. In RC I found no frost, sticky coldness. I did find small liquid build up around cap tube and RC evap but couldnt determine if water or oil. Found FC evap had some frost build up but frost build up was thin and easily removable with fingers. No stickiness to coil when compressor was directed to FC evap. Found no oil signs. Wasnt able to remove refrigerator from rested spot because feet/rollers were removed when installed and I couldnt access compressor but I could here compressor/condenser coil. Unit does appear to have a full no cooling sealed system issue. Will need to return with new sealed system oil less equip as well as compressor, non-uv dryer, etc. need office to reschedule once availability of parts is known. ordrng 1 Cnote (Need oil less gauges/equipment) and 1 Cnote (Need 3 hr repair reschedule) and 1 W10865322 (Rc evap) and 1 W11035643 (FC evap) and 1 W11025999 (Compressor) and 1 W11109499 (Non uv dryer) and 1 W11548259 (Condenser coil) and 1 W11024494 (Condenser fan motor assembly)"

Arrived on site and inspected washer issues. Customer advised the loads arent getting cleaned and her wash beads werent melting. Checked underneath the unit and found the actuator (new style) failed. Used truck stock W10913953 to complete the repair. Unit now operating properly. JOB COMPLETE CUSTOMER SATISFIED

"Arrived on site for refrigerator needing previously diagnosed deli ui, harness, ice door and led module. Upon arrival I reconfirmed prior diagnostics. Disassembled and installed all needed parts. I reasse and tested unit and found all previously failures with unit were nO longer present.

Arrived on site for a dryer that?s not drying clothes. Inspected unit and work area. The customer advised that it?ll take 2 to 3 cycles to dry clothes especially towels. Use the vent tester kit on the unit and found the unit showing for ventilation for all dryers. Took off the vent hose and added a sock to the end of the vent to test the unit again due to lint buildup inside the exhaust hose in the dryer. The unit showed good ventilation for gas dryers but poor ventilation for electric dryers. Disassembled unit and cleaned out all lint buildup inside the dryer. Read connected everything and tested the unit again with the sock. The unit still showed the same result. Took the sock off of the dryer and tested the unit. The unit showed good ventilation for all dryers. Tested the unit again with the vent hose on and found Poor ventilation for all dryers again. I explain to the customer that this would show their issue is with her vent inside the home going out.

Arrived on site for refrigerator freezing everything in RC compartment. Upon arrival I found all items in Rc compartment had frozen over from top shelfs to bottoms and front to back. I also found ui unresponsive to input. I was unable to pull find any accurate schematic sheet for unit specs. Every enters into diagnostics failed. Tried replacing control and got same response. Was unable to test unit further. Dampener motor is also stuck open.

Arrived on site for fridge raider that?s not keeping proper temperatures. Inspected unit and work area. The customer advised that the unit somewhat cycles between single digits in the freezer section and up to 30? in their freezer section and between lower 40s up to 55? in the refrigerator section. The customer is keeping this unit in the garage and I asked approximate temperatures he was getting in his garage during the day. The customer did advise that it?s getting up into the hundred degree area in his garage due to poor ventilation. Remove the evaporator cover and found a good frost pattern on the evaporator with no evidence of any defrost issues. The freezer was reading at 7?F. The refrigerator was sitting at 50?F. Took an amp draw off the compressor and found a good amp draw. I did inform the customer that it seemed to be that their issue was with the ambient temperature around this unit. Went over user care guide and specifications for this unit to be working properly. The unit is working as designed. Call complete.

"Arrived back on site to install previously ordered part. Gave customer the ice container so she could rinse it out. Advise her to simply transfer the ice and install it into the unit.

Arrived on site and inspected French door refrigerator not cooling in the refrigerator compartment. Confirmed the complaint and found the evaporator fan wasnt working. Got authorization and replaced it and unit began cooling. Advised the customer to wait approximately 24 hours for the unit to reach optimal temperatures. JOB COMPLETE

Arrived onsite for poor water flow through water dispenser. Customer bypassed filter and had good flow but when filter was inserted the unit would have low flow. Suspected failing housing W10862460. On arrival unit was functioning properly. Had no issues at dispenser. Customer will monitor

Arrived onsite for unit not wash clothes correctly. Put unit in diagnostics test and unit passed. Found stuck key error code. Ordered a control. Office to reschedule ; ordrng 1 W11417466 (CONTROL )

Arrived on site install previously diagnosed lint clip. Upon arrival disassembled unit and installed new part. Reassembled unit and ran a diagnostics test to find no abnormal sounds and all functions operating as designed. Call complete.

"Arrived on site to test unit for not heating. Found unit operating as designed. Door switches tested good. All fuses tested good. Replace diode and cap as a precautionary. Tested unit, unit works good. Job complete."

"Arrived on site and inspected range and found it is working properly previous technician completed repair. Apartment resident is not home to discuss with. Took multiple pictures of range operating normally

"Arrived on site for customer complaint of unit not heating, found failed heating element, also ordering idler assembly. Heater assembly

Arrived onsite for refrigerator deli control panel not functioning. Was sent with UI panel. Ordering deli control and harness just in case. Will need AUTHO. Office to reschedule; ordrng 1 W11170612 (harns-wire) and 1 WPW10677119 (cntrl-elec)

"Arrived onsite to replace ice maker, ordered by previous tech. Replaced ice maker. Tested in harvest and fill. Ice maker passed. No issues at this time. Job complete"

"Arrived on site to replace previously diagnosed ice maker. Replaced ice maker, tested unit, unit works good. No leaks detected. Job complete."

"Arrived onsite for unit making a noise. Upon further investigation. Found that the connector to the fan was some how loose, causing the compressor to work harder and making more noise. Re connected the the wire to the compressor fan. Unplugged for 5-10min. Unit started back on and fan came back on and noise was no longer there. No issues at this time. Job complete"

"Arrived onsite and tested unit for airflow and condensation issues. Drier itself is functioning as designed, however advised customer that vent should be checked for airflow efficiency and a damper to prevent back flow of outside temperatures."

Arrived on site(RentACenter) to test unit for multiple cycles needed to finish drying

"Arrived on site for no cool. Powered unit on compressor and fans powered on no frost forming on evaporator found traces of oil on evaporator. Replaced evaporator,compressor and installed a uv drier,vacuumed system down unit kept vacuum recharged system to manufacture spec powered unit on checked low side pressure good checked frost pattern good.

Arrived on site to test unit for unit sparking. Test unit and found burned out cap and diode. Will need new cap mag and diode

Arrived on site to test unit for door not staying on. Found left hinge lock broken. Test unit and unit test good job complete.

Arrived on site to replace control board. Replaced board test unit and unit heated to 350 with out turning off. Job complete. Ran for 20 minutes and still working.

"arrived on site for loud noise while dispensing water. Tested dispenser loud noise and weak water flow,installed bypass same issue diagnosed a defective filter head. Replaced filter head checked lines and connections no leaks,tested water dispenser unit working as designed.

"Arrived on site for icemaker issues. Diagnosed icemaker overfilling replaced defective icemaker ran new icemaker through a cycle passed,ran fill test passed.

Arrived onsite for unit not agitating. Looked under the unit and found that the wrong actuator was installed from the factory. Had actuator from truck stock to replace. Replaced Actuator. Tested unit. Unit tested good. No issues at this time. Job complete

"Arrived on site to test unit for tub sitting sideways. Found rear suspension bushings were broken. Replaced suspension and bushings, tested unit, unit works good. Found no signs of damage to tub. No leaks detected. Job complete."

Arrived on site to test unit for not draining. Found drain motor getting power but not spinning. Replaced drain pump test unit and unit test good job complete

"Arrived on site to test unit for little ice production. Found ice bin half full on arrival. Ran diagnostics and found ice maker not always responding. Verified voltage to ice maker. Temps in FC and RC both correct. Ice box fan operating as designed. Fill tube heater good. Replaced ice maker, tested unit, unit works good. No leaks detected. Job complete."

"Arrived on site for cooling complaint. Checked evaporator compartment good frost formation on coil,power cycled unit found compressor not powering on with multiple attempts from start diagnosed a defective starter. Installed a new starter powered unit on compressor powered on. ; used 1 8201786 (Start device) from stock"

Arrived onsite for unit making a ticking noise. Listened to the unit and heard a ticking noise and noise was coming from the back of the unit. Upon further inspection saw that the water hose on the out side of the unit was lightly smacking against the back of the unit. Went ahead and taped the hose going to the filter head in a different position to help with no noises. No noises at this time. Job complete

Arrived on site to test unit for unit leaking heat due to door not closing all the way. Found bad hinges and trims and inner liner. Also found right side panel damaged. Ordering parts office to reschedule. ; ordrng 1 WPW10299224 (Right hinge) and 1 WPW10299227 (Left hinge) and 1 WP9761344 (Liner door) and 1 W10761018 (Trim door) and 1 W10761014 (Trim door) and 1 WPW10162245 (Side panel)

"Arrived on site to replace valve from previous diagnosis. Replaced valve and ice maker is now receiving water. When reinstalling ice maker broken fill tube heater wire fell from fill tube hole. Replace fill tube with heater, tested unit, unit works good. No leaks detected. Job complete."

Arrived onsite for unit not freezing/cooling. Customer had a thermometer in the unit for days on the refrigerator and the refrigerator was only 58 degrees. Nothing in the freezer was frozen only cooling. The ice was good but customer said the it would leak water from time to time where the ice dispenser is. Concluded that it?s a sealed system issue because of un even temperatures. No issues at this time. Job complete