Near New Braunfels, TX 78130
Andrew
Job Details:
12/30/2020
DISHWASHER KITCHENAID KDTM704KPS0
"Arrived on site to test unit for leaking from left side door. When wash cycle started unit leaked immediately. Found drywall screw was between left door gasket and door. Removed screw, checked dispenser and vent tube. Tested unit and leak is no longer present. No leaks at time of service. Job complete."
Near Round Rock, TX 78681
Tommy
Job Details:
12/30/2020
REFRIGERATOR WHIRLPOOL WRF767SDHZ01
Arrived onsite for freezer light going out. Upon arrival found unit switches and lights worked bottom freezer light was dead had moisture in bulb. Spliced new light in. Light is now operating correctly. Job Completed.
Near Cedar Park, TX 78613
Wesley
Job Details:
12/30/2020
WASHER WHIRLPOOL WTW4816FW2
Arrived onsite and found unit unable to be properly installed because valve had been broken during move.
Near New Braunfels, TX 78132
Noah D
Job Details:
12/30/2020
MICROWAVE WHIRLPOOL KOCE500ESS01
"Arrived on site to inspect microwave for not heating and causing sparks. Checked wave guide and found large amounts of silicone, will need new wave guides and clear all silicone, ordering covers. Office to reschedule ; ordrng 2 W10120230 (PLATE)s"
Near Austin, TX 78733
Kevin
Job Details:
12/30/2020
RANGE GE JGP940SEK2SS
"Arrived on site and replaced all parts that showed up. Took one picture of flame heights and sent it to KB/AHS. Right front burner switch is not working now, a new switch harness will be needed to correct issue.; ordrng 1 WB18T10452 (Switch harness)"
Near Austin, TX 78724
Matthew
Job Details:
12/30/2020
REFRIGERATOR WHIRLPOOL WRS588FIHZ00
"Arrived onsite to replace previously diagnosed parts. When replacing upper air duct, had the same result. Called tech line for assistance and stated duct requires air duct clips SR7729622343. Will order clips to complete job. Office to reschedule.; ordrng 7 W10331728 (clip)s"
Near New Braunfels, TX 78132
Noah D
Job Details:
12/30/2020
DISHWASHER MAYTAG MDB4949SDE0
"Arrived on site to inspect dishwasher or not starting up, upon inspection found the motor capacitor had melted
Near Austin, TX 78723
Matthew
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRS588FIHV00
"Arrived onsite for refrigerator doors not aligned. Upon inspection found hinges screws backing out causing cam to not catch properly. Removed door to secure all screws, reset door and doors aligned properly, job complete"
Near Meadowlakes, TX 78654
Cliff
Job Details:
12/29/2020
OVEN WHIRLPOOL RBS305PDB12
Arrived on site to diagnose an oven that is not heating. Found failed thermal fuse. Replaced fuse and tested unit. Found all is working properly at this time.
Near Austin, TX 78753
Luis
Job Details:
12/29/2020
DISPOSAL GAGGENAU MY NAME IS BOB
Near Georgetown, TX 78633
Kayman
Job Details:
12/29/2020
DISHWASHER GE GLD6960N20SS
Arrived onsite for dishwasher making drinking or growling noise. Upon inspection I found the unit would start to rattle or make a loud chattering noise coming from the drain pump when engaged. It sounds like the pump is beginning to fail. I recommended replacing the drain pump and impeller kit.
Near Taylor, TX 76574
Andy
Job Details:
12/29/2020
WASHER KENMORE 110.2235251
Arrived on site for washer not operating properly. Tested and inspected unit and found failed control and failing gearcase. Also found issues with latch. No repairs are to be done at this time. No water leaks present at time of service.
Near Pflugerville, TX 78660
Scott
Job Details:
12/29/2020
DRYER WHIRLPOOL WED4850HW0
Arrived on site for dryer not heating. Found element burned out due to bra wire grounding out heater. Remove wire and replaced element. Heating unit is normal and drying properly no lint buildup at time of service job complete.
Near Horseshoe Bay, TX 78657
Cliff
Job Details:
12/29/2020
DRYER WHIRLPOOL MED6630HC1
Arrived on site to diagnose a dryer that will not always complete cycles. Tested unit and found no errors saved in control or failures to unit at this time. Advised homeowner that small loads may not always contact humidity sensors causing unit to shut off prematurely. No further repairs are needed and all is working properly at this time.
Near Pflugerville, TX 78660
Scott
Job Details:
12/29/2020
RANGE WHIRLPOOL WFC315S0JS0
Arrived on site for broiler draw missing glides . Installed glides . Broiler draw in now installed correctly in range . Job complete
Near Austin, TX 78745
Luis
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRT108FZDM05
Arrived on site for no cool. Compressor running no frost pattern on evaporator diagnosed leak at lokring connection on evaporator ordering evaporator and compressor. ; ordrng 1 W11407409 (Evaporator) and 1 W11209866 (Compressor) and 1 W10897195 (Coupler) and 2 W11401413 (Coupler)s and 2 W11401417 (Coupler)s and 1 2hrs (2hrs)
Near Spring Branch, TX 78070
Andrew
Job Details:
12/29/2020
OVEN GE PT9550SF4SS
"Arrived on site to test unit for probe constantly lit when operating upper oven. Replaced meat probe jack and harness, removed old control board and found new control was damaged. Put unit back together, tested unit, same issue. Needing control board to fix issue.; ordrng 1 Wb27x21657 (board machine contro)"
Near Austin, TX 78750
Justin
Job Details:
12/29/2020
WASHER WHIRLPOOL WTW5000DW3
"Arrived on site for washing machine that was not agitating and would not stop draining unless unplugged. Upon arrival customer had unit unplugged and when I plugged it in it went right into draining and would not stop. I canceled cycle and drain stopped. I put unit into diagnostics mode and found no stored error codes. I put unit into test cycle and manual tests and found unit working as designed. I gained access to control and tested VAC to L1 and Neutral and found 120V. I then tested VDC at J12 connector and found low voltage with pin unconnected indicating malfunctioned control. Replaced control and calibrated unit, unit now working as designed. Call complete."
Near Horseshoe Bay, TX 78657
Cliff
Job Details:
12/29/2020
OVEN JENN-AIR JJW3830WP00
Arrived on site to replace UI for oven. Replaced part and tested unit. Found all is working properly at this time.
Near Austin, TX 78717
Tommy
Job Details:
12/29/2020
RANGE WHIRLPOOL WFE515S0JS0
Arrived onsite for previously diagnosed parts. Upon arrival replaced main harness and block.
Near Temple, TX 76502
James
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRS588FIHZ00
Arrived on site and tested operation. Found damper very loud when opening and closing. Tested in diagnostics and it only recognized position ever 3rd or 4th cycle. Installed new damper and tested. Unit tests good. Job complete
Near Lago Vista, TX 78645
Lou
Job Details:
12/29/2020
WASHER WHIRLPOOL WTW8500DC6
"Arrived on site to inspect washer noises. Upon further inspection, customer advised that the unit is making a metal grinding noise set the beginning of the cycle for approximately 1 minute and then goes away and the unit operates just fine. I placed the unit in diagnostics showing no error codes. Contrived with testing and the unit operated as designed with no unusual noises. I manually tested the agitate and spin cycles and still no noises. Tilted the unit back and all components look good with no signs of gearcase oil leaking. I tested the unit in a normal wash cycle and still no noises. Contacted techline and spoke to Scott and advised of the complaint and my findings. Scott documented complaint and provided file #7729583072. I advised customer to take a video of the noise if it comes back and then call it in for service. No water leaks observed during service, job completed."
Near Austin, TX 78733
Kevin
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDF520PADM7
"Arrived on site and inspected dishwasher and found connection to heating Element is loose, after resetting it confirm it is working properly by running a diagnostic cycle. Customer is already using rinse aid, discussed drawing expectations, job complete"
Near Pflugerville, TX 78660
Scott
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDF330PAHS3
Arrived on site for rack support wheeel broken off . Replaced wheel supports . Upper rack is performing normally. No water leaks detected at time of service. Job complete
Near Round Rock, TX 78681
Kayman
Job Details:
12/29/2020
DRYER WHIRLPOOL LDR3822PQ3
Arrived onsite to install previously diagnosed parts. I installed the motor and blower wheel. After testing the unit I found the wheel rubbing against the housing causing a screeching noise. I found the panels out of alignment due to a missing screw. I added the screw and the unit now only screeches right at the start then sounds normal. The customer stated hat this shouldnÂ’t be an issue. Job complete.
Near Austin, TX 78749
Kevin
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDT970SAHZ0
"Arrived on site and inspected dishwasher and found plastic stop on upper rack is off, plastic retainer on upper rack is also off. Cover is missing from mounting point, corrected both upper rack pieces but will need a new mounting point cover sent directly to homeowner; ordrng 2 W10795980 (D2C tub cap)s"
Near Meadowlakes, TX 78654
Cliff
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRX986SIHZ00
"Arrived on site to install pressure regulator, valve, waterline, ice guide, and mullion for refrigerator. Replaced all parts and tested unit. Found all is functioning properly at this time. No leaks were found after services were performed."
Near Austin, TX 78749
Leonardo
Job Details:
12/29/2020
OVEN LG LRG3193ST00
Arrived on site to replace igniter. Replaced part test unit and unit heating to 350 job complete.
Near Austin, TX 78758
Justin
Job Details:
12/29/2020
DRYER WHIRLPOOL WGD5100HW0
Arrived on site for dryer that would shut off immediately. Location is appliance dealer and the team could not locate unit for service. No service performed. Call complete.
Near Austin, TX 78758
Justin
Job Details:
12/29/2020
WASHER MAYTAG MVW7232HW0
Arrived on site for washing machine that would not spin. Put unit into diagnostics mode and found stored error code F7E4 for shifter error. Ran diagnostics cycle and manual spin speed cycle and found unit not spinning at all. Gained access to shifter and found physically broken off magnetic ring not allowing tub to spin. Installed new shifter and tested unit in diagnostics mode. Unit now working as designed. Call complete.
Near Jarrell, TX 76537
Kayman
Job Details:
12/29/2020
DRYER WHIRLPOOL WED7120HW0
Arrived onsite to install previously diagnosed parts. I installed the UI and tested the unit. The unit is working as designed at this time. Job complete.
Near Austin, TX 78756
Wesley
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRS321SDHW01
Arrived onsite and found unit evap drain frozen over. Ordering steamer to repair by clearing frozen line. Tech to verify drain not foamed through. ; saved tckt
Near Cedar Park, TX 78613
Justin
Job Details:
12/29/2020
WASHER WHIRLPOOL WTW4850HW1
"Arrived on site to install previously diagnosed parts. Installed new motor, control, and cam. Then put unit into diagnostics mode and calibrated unit. Tested unit and found noise still occurring. Called techline and spoke with Bruce and received SR# 7729530957 (same as prior call for unit). Found that control that was sent over to be installed was an older control and the newer control he said was supposed to be coming out by sometime end of December and will no longer have this issue. Stated they will be coming out with service pointer for issue. Bruce also stated unit is safe to use in the mean time. Bruce said to request fresh stock from Plainfield for the control. Office to reschedule.; ordrng 1 RESEARCH (W11498190 FROM NEW STOCK AT PLAINSFIELD)"
Near Georgetown, TX 78633
Kayman
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL ED5KVEXVB00
Arrived onsite for refrigerator loosing cool in both sections but still making ice. Upon inspection I found the evaporator incased in ice. I was able to access and test the bimetal. I found the bi metal showing incorrect resistance which would cause the defrost issue. I engaged a forced defrost and tested amp draw at the heater. It tested good.I replaced the bimetal but could not steam all of the ice.
Near Killeen, TX 76549
Al
Job Details:
12/29/2020
OVEN FRIGIDAIRE FGF326ASD
"Arrived to inspect Frigidaire range oven door hinge issues.Confirmed the unit will require the ordered hinge to complete the repair.Office to reschedule the customer for return service when the part arrives.Needs more work.; ordrng 1 316566207 (hinge,oven door l) and 1 316566208 (hinge,oven door r)"
Near Austin, TX 78751
Wesley
Job Details:
12/29/2020
REFRIGERATOR KITCHENAID KBBL306ESS01
Arrived onsite for stuck filter. Removed filter and verified filter issue and housing is fine and advised customer on filter reset feature. Advised customer on filter replacement.
Near Buda, TX 78610
Kevin
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRS325FDAM04
Arrived on site and inspected refrigerator and found no ice production. Cycles icemaker and Motor is operating properly but there is no water. Sound water filter is not engaged in housing attempted to remove water filter and found it is jammed. Was able to pull it out and water is now working at dispenser and icemaker is able to fill. Will need to bring back a new water filter housing to correct issue I quoted customer for repair. t; ordrng 1 W10862461 (Filter housing)
Near Canyon Lake, TX 78132
Andrew
Job Details:
12/29/2020
RANGE KITCHENAID KFDC558JSS00
Arrived on site to replace parts from previous diagnosis. . Needing right center rear orifice holder. Office to reschedule.; ordrng 1 W11398676 (REPLACED ORF)
Near Round Rock, TX 78665
Cliff
Job Details:
12/29/2020
MICROWAVE WHIRLPOOL WMH31017HS4
Arrived on site to replace interlock for microwave. Replaced part and found no change in operation. Verified all switches as good. Did note error indicators on breakers in breaker box our gym and slightly lit indicating electrical issue in home. Homeowner will need electrician to correct failure.
Near Austin, TX 78738
Brandon
Job Details:
12/29/2020
MICROWAVE GE PEB7226SF2SS
"Arrived on site for customer complaint of unit sparking during use, found mag tube blown and shorted causing internal frame damage.
Near Austin, TX 78725
Jacob
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDF330PAHS3
Near Austin, TX 78749
Kevin
Job Details:
12/29/2020
RANGE WHIRLPOOL WGE745C0FS01
"Arrived on site and found all burners are high, adjusted all to customer requested level. Range is operating properly now, job complete"
Near Hutto, TX 78634
Jimmy J.
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDF330PAHW1
Near Buda, TX 78610
Richard
Job Details:
12/29/2020
WASHER WHIRLPOOL WFW9200SQ02
"Arrived onsite for the washer leaking water. Upon inspection found that the bellow is torn causing the leak. During replacement of bellow found that the screw hold the control panel to the dispenser assembly is stripped and will not come out and its extremely rusty. Will have to break part of control panel to remove the control panel so we can get to the top screws holding the front panel on. Will need to order a control panel , dispenser assembly, screws. ordrng 1 8183228 (Control panel) and 1 W10157886 (Dispenser assembly) and 2 8182214 (Screws)s"
Near Austin, TX 78754
Matthew
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDT970SAHZ0
Arrived onsite for spray arms not working. Put unit in diagnostics and found stored error code F4E3 wash motor not running. Ran test cycle and found unit filling and draining. Wash motor would not energize. Will need to order and replace Pump and motor W11087376. Office to reschedule. ; ordrng 1 W11087376 (pump&motor)
Near Austin, TX 78741
Kevin
Job Details:
12/29/2020
DRYER WHIRLPOOL WED4850HW0
"Arrived on site and found power is the same as the previous visit, took pictures, there has been no correction performed
Near New Braunfels, TX 78132
Andrew
Job Details:
12/29/2020
DRYER WHIRLPOOL WET4024HW0
"Arrived on site to test unit for not heating. Found bad element and thermostat. Replaced element and thermostat. Tested unit, unit works good. Job complete."
Near Temple, TX 76504
Tyler
Job Details:
12/29/2020
REFRIGERATOR GE GSH22UFREWW
Arrived on site for refrigerator not cooling. Upon arrival I found that the unit was plugged in and the lights are on but unit was not getting power or running. Upon further inspection found the main control the back of the unit was receiving 120 V but when I uninstalled the main control and flipped it over I found a nasty burn mark on the back side indicating that the board had shorted out. In order to test further we will need to return with a new main control ; ordrng 1 WR55X10942P (board asm main contr)
Near Georgetown, TX 78633
Kayman
Job Details:
12/29/2020
RANGE WHIRLPOOL WFG550S0HZ1
Arrived onsite to install previously diagnosed parts. I installed the main control and tested the units preheat. I let the oven get up to 350 degrees and I waited for about 10 mins to see if the error would return. The error did not return and the unit is working as designed at this time. No gas leaks were detected during time of service. Job complete.
Near Temple, TX 76502
Al
Job Details:
12/29/2020
REFRIGERATOR FRIGIDAIRE FRS26KF5DS4
Arrived to inspect ice maker not working.Confirmed the complaint and removed and replaced it.Tested as designed.Customer will require a new filter to be purchased by customer.Job completed
Near Killeen, TX 76542
Al
Job Details:
12/29/2020
DRYER GE GFDN240EL0WW
Arrived to inspect dryer noises. Disassembled the unit and discovered the unit is miss both front bearings. Ordering top kit bearing assembly and front bearings will return with the pulley and belt.Office to reschedule the customer for return service service visit.Needs more work.; ordrng 1 WE01X25434 (kit top bearing asse) and 2 WE1M504 (DRYER FRONT BEARING DRUM SLIDE - WHITE)s
Near Bastrop, TX 78602
Andy
Job Details:
12/29/2020
OVEN WHIRLPOOL WFE525S0JZ0
Arrived on site to install previously diagnosed hinges. Removed failed parts and replaced with new. Tested unit and all operations are normal. No other repairs are needed at this time.
Near Andice, TX 78628
Lou
Job Details:
12/29/2020
OVEN WHIRLPOOL WOS51EC0HS01
"Arrived on site to inspect wall oven not working. Upon further inspection, customer advised that while cooking, the display glitches and the unit doesnÂ’t heat correctly. I placed the unit in diagnostics and checked for error codes. I found F6E4. Following the tech sheet for this error code, the main control should be replaced. I advised the customer of my findings. I am ordering the main control and office to schedule return service due to the availability of parts. ; ordrng 1 W11261167 (cntrl-elec)"
Near Temple, TX 76502
Tyler
Job Details:
12/29/2020
DRYER MAYTAG MEDX655DW1
Arrived on site for dryer not heating properly. Upon arrival found after disassembly that the unit was receiving 240 V from the power outlet and the terminal block was still intact and the timer and door switch are functioning as designed. Then found that the heating element and three out of the four thermal fuse is working but the high limit thermal cut off had shorted out due to a significant clog inside the vent hose of the dryer. . I did recommend to the customer that they have someone come out to double check and verify that the rest of the venting inside the house is not clogged but at this point unit is functioning as designed call complete.
Near Pflugerville, TX 78660
Kayman
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRX735SDHZ02
Arrived onsite for refrigerator not making ice. Upon inspection I found the ice maker full of ice but I could not get it to harvest. I replaced the ice maker and HV control. The IM harvested and filled as designed. No leaks were detected during time of service. Job complete.
Near Austin, TX 78738
Jacob
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDT790SAYM1
Arrived onsite for unit not stable inside the cabinet space. Looked at unit saw that the mounting brackets were missing/damaged also on the inner door the top left and right screws are missing. Ordered parts. Office to reschedule ; ordrng 2 WP308685 (screw)s and 2 WP8269145 (brckt-mtg)s and 2 WPW10348408 (screw)s
Near Austin, TX 78753
Matthew
Job Details:
12/29/2020
FREEZER WHIRLPOOL WRF535SMBB00
"Arrived onsite for refrigerator ice maker not producing ice. Upon inspection found ice maker would not respond to any test. Need ice maker replaced. Quoted customer 108.64 for parts and 209.99 for labor totaling 318.63 before taxes. Replaced ice maker, tested unit and is functioning properly. No leaks present at this time. Job complete"
Near Austin, TX 78745
Brandon
Job Details:
12/29/2020
MICROWAVE GE JEB1860SM1SS
"Arrived on site for customer complaint of unit not responding to certain buttons. Found failed UI control part WB56X10794,
Near Georgetown, TX 78626
Lou
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRX986SIHZ00
"Arrived on site to inspect refrigerator noises. Upon further inspection, I could hear the refrigerator making a vibrating be once I walked into the home. I placed the unit in diagnostics and tested the evaporator fans in test #3 and found the FC evaporator fan making the noise. I disassembled the FC door/drawers and removed the FC evap cover and found the evaporator with a good frost pattern. Also found evidence of frost/ice build up on the right side and middle of the evaporator. The evap fins were laid over under the fan and there was still ice on the cap tube. I advised the customer of my findings and advised that this issue is from an air leak. As a precaution, I removed and replaced the evap motor/harness and retested. Unit is operating as designed. While in diagnostics, I changed the defrost time to 8 hours (#2) in test #7. Advised customer of my repairs. No water leaks observed during service, job completed."
Near Georgetown, TX 78628
James
Job Details:
12/29/2020
REFRIGERATOR KITCHENAID KSRS25FTMS01
Arrived on site and tested operation. Found ice maker motor running but is stripped out and not able to turn ejector fork. Office to schedule return services due to part availability.; ordrng 1 2198597 (icemaker assy)
Near Leander, TX 78641
Tommy
Job Details:
12/29/2020
WASHER WHIRLPOOL WTW7500GW3
Arrived onsite for washer lid cracked. Upon arrival found lid right side cracked. Replaced lid and tested. Unit is now operating as designed. Job Completed.
Near Austin, TX 78749
Leonardo
Job Details:
12/29/2020
RANGE WHIRLPOOL WFE505W0HS1
Arrived on site to replace hinges. Replaced hinges test unit and unit test good job complete.
Near Leander, TX 78641
Lou
Job Details:
12/29/2020
REFRIGERATOR AMANA AFD2535DEW
"Arrived on site to inspect refrigerator FC door not closing all the way. Upon further inspection, I found that the right rail was jammed and not able to close. I removed the door and adjusted the rail and rack shaft and re-installed the door and tested. Door is closing and sealing as designed. Using my shop vac, I cleared all of the ice/frost from the FC section. No water leaks observed during service, job completed."
Near Round Rock, TX 78665
Jimmy J.
Job Details:
12/29/2020
DISHWASHER KITCHENAID KDTE204ESS2
"Arrived on site for Dishwasher won't complete a cycle. Sometimes it will fill with water and start a cycle open the detergent dispenser, and then stop. The blue light remains on, but the dishwasher stops working. The drain function works fine. AFTER DROPPING THE SOAP IT GOES SILENT AND JUST STOPS DOESN'T ADVANCEPlaced in diagnostics and got F7E1. Ran full diagnostics and after water fill you only heard clicking. Removed door panel and tested for proper voltage. Pump and motor has failed. Removed pump and motor and installed new pump and motor. Ran diagnostics again. Dishwasher operating as designed. No leaks detected. Job completed."
Near The Hills, TX 78738
Brandon
Job Details:
12/29/2020
WASHER WHIRLPOOL MVW7232HW0
"Arrived on site for customer complaint of error codes, found error codes F0e9 and foe5 in diagnostics mode, found unit was not level, I leveled unit and ran spin test, unit tested good.
Near New Braunfels, TX 78132
Andrew
Job Details:
12/29/2020
ICE MACHINE KITCHENAID KUIX535HPS00
"Arrived on site to test unit for loud noise. Found cap tube was vibrating on condenser. Moved cap tube, tested unit, unit sounds good. Verified with owner noise is gone. No leaks detected. All functions worked good in diagnostics. Job complete."
Near Lakeway, TX 78738
Brandon
Job Details:
12/29/2020
MICROWAVE WHIRLPOOL KOCE500ESS09
"Arrived on site to replace harness with door switches, after replacing, unit tested good."
Near Austin, TX 78723
Matthew
Job Details:
12/29/2020
OVEN WHIRLPOOL WOS92EC0AS02
Arrived onsite to replace previously diagnosed parts. Replaced glass and fuse. Tested unit to 350 degrees and unit is functioning properly. Job complete
Near Canyon Lake, TX 78133
Andrew
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDT920SADM2
"Arrived on site to test unit for not filling with water. Found bad inlet valve. Replaced valve, tested unit, unit works good. No leaks detected at time of service. Job complete."
Near Dripping Springs, TX 78620
Jacob
Job Details:
12/29/2020
WASHER WHIRLPOOL WFW5620HW2
Arrived onsite for unit shaking more than usual. Customer said floor was re done not too long ago. Looked at unit. Found that the unit is resting on the plastic tub. Re leveled unit. Tested unit at maximum speed. No irregular vibrations at this time. Job complete
Near New Braunfels, TX 78132
Noah D
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WSR57R18DM02
"Arrived on site to inspect fridge for not cooling, upon inspection found the installation was done incorrectly and must be fixed, right side evap was covered in frost, heater worked and control sent voltage, ordering thermistor and instructed customer to defrost fridge and get with installers. ; ordrng 1 WPW10383615 (THERMISTOR ) and 1 W10383615 (EVAP THERMISTOR )"
Near New Braunfels, TX 78132
Andrew
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WSR57R18DM02
"Arrived on site to replace evap therm and therm. Replaced parts, tested unit and control box was acting erratically. Needing control box to fix issue. Office to reschedule.; ordrng 1 W10608692 (cover) and 1 W11282569 (contrl-box)"
Near San Marcos, TX 78666
Richard
Job Details:
12/29/2020
DRYER ROPER RED4516FW0
"Arrived onsite for the dryer not spinning. Replaced belt, idler pulley, motor pulley. Dryer tested fine and is heating fine. Complete"
Near Temple, TX 76502
Tyler
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRS571CIHZ01
Arrived on site for refrigerator not allowing water filter to stay in properly. Water pressure to the fridge seemed fine and not too high but the casing around the filter that holds it in place is not latching on properly and the filter head is showing a filter out whenever itÂ’s activated; ordrng 1 WPW10394053 (housing)
Near Canyon Lake, TX 78133
Andrew
Job Details:
12/29/2020
DRYER MAYTAG MEDB765FW0
"Arrived on site to test unit for clean vent light constantly illuminated. Ran air flow test and found unit was not receiving proper ventilation. Customer cleaned venting leading to exterior. Tested unit and air flow was now good but light stayed illuminated. Checked all sensors and all tested good. Checked venting in unit and itÂ’s all clear. Found bad control board. Replaced control, tested unit, unit works good. Job complete."
Near Blanco, TX 78606
Brandon
Job Details:
12/29/2020
ICE MACHINE KITCHENAID KUIX535HPS00
"Arrived on site for customer complaint of no ice production, found unit would not circulate water, fill to proper amount and will not drain the reservoir. Ordering circulating pump and reservoir drain pump. ; ordrng 1 WPW10489125 (Pump)"
Near Austin, TX 78735
Kevin
Job Details:
12/29/2020
WASHER WHIRLPOOL MHW6630HW2
arrived on site and inspected washer and did not find any water trails or signs of leaking. Inspected Bellow, Dispenser drawer, and vent hose on the top of the tub. Spoke with techline and this unit has already been updated and service pointer W11481731 Was already updated at the factory. Requested that customer continue to monitor washer. Took several pictures, Tech line does not have any recommended parts or repairs to address experience 7729598309"
Near Seguin, TX 78155
Noah D
Job Details:
12/29/2020
WASHER MAYTAG MVWB835DW0
"Arrived on site to inspect washer for not starting, replaced console per last visit and washer started immediately, checked for functions and found no issues. . Complete"
Near Manor, TX 78653
David S
Job Details:
12/29/2020
DISHWASHER FRIGIDAIRE FBD2400KB10B
Arrived on site for dishwasher leaking. I inspected the unit and work area. I found the spray arms melted and spraying water directly into the door seals causing them to leak and water to splash out. The spray arm will need to be replaced. ; ordrng 1 5304518927 (SPRAY ARM )
Near Austin, TX 78747
Leonardo
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDF520PADM7
Arrived on site to test unit for unit leaking. Test unit and found unit leaking from vent. Ordering vent office to reschedule. ; ordrng 1 W11227945 (DEFLECTOR ) and 1 WPW10329609 (VENT)
Near Austin, TX 78744
Kevin
Job Details:
12/29/2020
WASHER WHIRLPOOL WFW9200SQ03
"Arrived on site and found washer is stacked, Bellow spring is loose and sitting inside tub. Reattached it and sent a short video to KB/AHS of Bellow now attached properly. Also found one baffle is broken off inside basket, this will need to be ordered, took picture.; ordrng 1 WPW10250572 (Baffle)"
Near Round Rock, TX 78664
Kayman
Job Details:
12/29/2020
OVEN WHIRLPOOL WGE745C0FS01
Arrived onsite for oven not heating properly. Upon inspection I found good voltage to the unit. I accessed the rear panel and found the lower bake element was disconnected. I also found the lower sensor slightly out of range. I replaced the sensor and reassembled the unit. I found the unit now heating properly. The customer brought to my attention a broken door handle and panel. I found the door panel separating and the screw not able to make good contact with the handle I added a piece of plastic in the screw port to get them by unit we can return with a door assembly. Ordering Door assm (W10877562). Office to R/S due to part availability. ; ordrng 1 W10877562 (glass-door)
Near Canyon Lake, TX 78133
Andrew
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDT730PAHZ
Arrived on site to test unit for leak. Found unit had water and food pieces in dishwasher. Found water and food was from not having a high drain loop causing back flow. Installed high drain loop, tested unit, and found no leaks form connections at time of service. Gaskets are sealing good.
Near New Braunfels, TX 78130
Noah D
Job Details:
12/29/2020
REFRIGERATOR JENN-AIR JB36NXFXRE01
"Arrived on site to inspect fridge for a bent door, upon inspection found the inner door was not bent, all the door hardware was loose and causing gapping, tightened down all hardware and checked for gaps, none found. Complete"
Near Temple, TX 76502
Tyler
Job Details:
12/29/2020
WASHER ROPER RTW4516FW2
Arrived on site for washer not running through cycles correctly. Upon arrival I found unit was in flood mode. The Drain pump wire harness had broken from the pump. I repaired the harness an reassembled unit. After repair unit is functioning as designed. Call complete.
Near Cedar Park, TX 78613
Justin
Job Details:
12/29/2020
MICROWAVE WHIRLPOOL WMH53521HZ4
Arrived on site for microwave with the light under unit not turning off. Found that the control panel was not responding and allowing light to turn off. Replaced control. Tested unit and unit now working as designed.
Near Seguin, TX 78155
Richard
Job Details:
12/29/2020
REFRIGERATOR GE GTS18DBMCLWW
Arrived onsite for the refrigerator making a loud noise. Upon arrival customer had unplugged the refrigerator for a whole day and it was unplugged. Plug refrigerator back in and compressor came on and is running good. Evaporator fan is running and a frost pattern was forming. Waited a few to see if the noise would come back and nothing. Advised customer to take a video recording of the noise if it comes back. Refrigerator is cooling and running fine. Complete
Near Pflugerville, TX 78660
David S
Job Details:
12/29/2020
DRYER WHIRLPOOL WED5620HW1
"Arrived on site for dryer making a noise. I inspected the unit and work area. I found the dryer making a screeching noise and a loud thump. I completed service pointer W11378591A, after finding marks under the drive motor plate. I also replaced the tensioner pulley, due to it making a screeching noise. I reassembled the unit. I placed a blanket in the dryer and tested it in front of the customer. The noise is gone and the customers agrees. Job complete."
Near Kyle, TX 78640
Richard
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRS325FDAM02
Arrived onsite for the refrigerator leaking water. During testing found that the leak is coming from the freezer section coming from the drain. Drain is clogged. Removed drain tube and removed the clog that was inside it and removed ice build up on the bottom liner of freezer . Clogged was removed and drain is clean and clear of debris.
Near Seguin, TX 78155
Noah D
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL WRF535SWHZ02
"Arrived on site to inspect fridge for not lightning of closing correctly, upon install of led found the left side slide holder had cracked causing gap in door, was not visible due to ice last time. Ordering holder. Office to reschedule; ordrng 1 W10284684 (HOLDER ) and 1 W10284685 (HOLDER )"
Near New Braunfels, TX 78130
Noah D
Job Details:
12/29/2020
WASHER WHIRLPOOL WTW4850HW1
"Arrived on site to inspect washer for leaking, upon inspection found the leaking originating from back right, could not find any cracks but all hosing did not leak, ordering tub and retuning with drain system. Office to reschedule ; ordrng 1 W10238320 (TUB)"
Near Canyon Lake, TX 78133
Andrew
Job Details:
12/29/2020
RANGE WHIRLPOOL WFE505W0JZ0
Near Georgetown, TX 78628
Kayman
Job Details:
12/29/2020
WASHER MAYTAG MHW5500FW1
Arrived onsite to install previously diagnosed parts. I installed the bellow and tested the unit through diagnostics cycle. The unit is working as designed at this time. No water build up and no leaks were detected during time of service. Job complete.
Near New Braunfels, TX 78132
Noah D
Job Details:
12/29/2020
OVEN WHIRLPOOL KODE500ESS05
"Arrived on site to inspect oven for not heating correctly, upon inspection found the oven working correctly but was too hot, found the oven was calibrated up 20, recalibrated and tested. No issues. Complete"
Near Dripping Springs, TX 78620
Jacob
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL WDF330PAHS3
Arrived onsite for door to unit not staying open or completely closed. Tested door. Door would not hold in position. Looked at unit. Found that pads had both come off. Replaced pads. Tested unit. Unit tested good. No issues at this time. Job complete
Near Briarcliff, TX 78669
Jacob
Job Details:
12/29/2020
DISHWASHER WHIRLPOOL KDTE204KPS0
Arrived onsite for unit making noise when opening the door. Tested door. Found that the kick plate was not screwed on properly but backwards. Re attached kick plate correctly. Tested unit. Unit tested good. No leaks at this time. Job complete
Near Liberty Hill, TX 78642
Tommy
Job Details:
12/29/2020
REFRIGERATOR WHIRLPOOL GZ25FSRXYY2
"Arrived onsite for refrigerator pouring slowly, ice maker auger not turning off and unit having ice on bottom. Upon arrival found auger operating as designed UI needed to be reset. Found reservoir not allowing water to travel through correctly. Replace reservoir and tested unit is now operating correctly. Found drain tube clogged. Used needles to clear. Job Completed."
Near Austin, TX 78750
Justin
Job Details:
12/29/2020
DISHWASHER KITCHENAID KDFE104DSS4
Arrived on site to install previously diagnosed parts. Installed new sump and motor and tested unit. Unit now working as designed. Call complete.
Near Kyle, TX 78640
Richard
Job Details:
12/29/2020
REFRIGERATOR GE Gfe28gskfss
Arrived onsite for the refrigerator having intermittent cooling issues and drain tube is clogged. Replaced main control and drain tube and removed the ice build up and clogged that was in the drain.
Near Killeen, TX 76542
Tyler
Job Details:
12/29/2020
WASHER WHIRLPOOL WTW8040DW4
Arrived on site for washer not working correctly after previously repaired and rebuild. Con further inspection and entering diagnostics I found that there was an F7e9 error code indicating that the rotor was locking up on the unit. Upon further inspection of the rotor I found that there was nothing causing the road to get stuck and it freely spun as designed. After disassembling the rotor and stater from the gear case I was able to determine that the gear case is grinding internally and the gears for agitation mode when the gear case is activated is not aligned correctly we will need to return with new gear case in order to resolve the issue office to reschedule once availability of parts is known; ordrng 1 W10734521 (slider) and 1 W11455453 (GEARCASE)